* [PATCH 1/1] Staging: comedi: s626: fix comment issue
@ 2016-06-08 9:48 Ravishankar Karkala Mallikarjunayya
2016-06-08 10:00 ` Ian Abbott
0 siblings, 1 reply; 2+ messages in thread
From: Ravishankar Karkala Mallikarjunayya @ 2016-06-08 9:48 UTC (permalink / raw)
To: abbotti, hsweeten, gregkh; +Cc: devel, linux-kernel, ravishankarkm32
This fixes up a WARNING: 'Block comments use a trailing */ on a
separate line'found by the checkpatch.pl tool.
Signed-off-by: Ravishankar Karkala Mallikarjunayya <ravishankarkm32@gmail.com>
---
drivers/staging/comedi/drivers/s626.h | 356 ++++++++++++++++++++++------------
1 file changed, 237 insertions(+), 119 deletions(-)
diff --git a/drivers/staging/comedi/drivers/s626.h b/drivers/staging/comedi/drivers/s626.h
index b83424e..6a00a64 100644
--- a/drivers/staging/comedi/drivers/s626.h
+++ b/drivers/staging/comedi/drivers/s626.h
@@ -29,8 +29,10 @@
#define S626_ENCODER_CHANNELS 6
#define S626_DIO_CHANNELS 48
#define S626_DIO_BANKS 3 /* Number of DIO groups. */
-#define S626_DIO_EXTCHANS 40 /* Number of extended-capability
- * DIO channels. */
+#define S626_DIO_EXTCHANS 40 /*
+ * Number of extended-capability
+ * DIO channels.
+ */
#define S626_NUM_TRIMDACS 12 /* Number of valid TrimDAC channels. */
@@ -48,21 +50,29 @@
#define S626_GSEL_BIPOLAR10V 0x00A0 /* S626_LP_GSEL setting 10V bipolar. */
/* Error codes that must be visible to this base class. */
-#define S626_ERR_ILLEGAL_PARM 0x00010000 /* Illegal function parameter
- * value was specified. */
+#define S626_ERR_ILLEGAL_PARM 0x00010000 /*
+ * Illegal function parameter
+ * value was specified.
+ */
#define S626_ERR_I2C 0x00020000 /* I2C error. */
-#define S626_ERR_COUNTERSETUP 0x00200000 /* Illegal setup specified for
- * counter channel. */
+#define S626_ERR_COUNTERSETUP 0x00200000 /*
+ * Illegal setup specified for
+ * counter channel.
+ */
#define S626_ERR_DEBI_TIMEOUT 0x00400000 /* DEBI transfer timed out. */
/*
* Organization (physical order) and size (in DWORDs) of logical DMA buffers
* contained by ANA_DMABUF.
*/
-#define S626_ADC_DMABUF_DWORDS 40 /* ADC DMA buffer must hold 16 samples,
- * plus pre/post garbage samples. */
-#define S626_DAC_WDMABUF_DWORDS 1 /* DAC output DMA buffer holds a single
- * sample. */
+#define S626_ADC_DMABUF_DWORDS 40 /*
+ * ADC DMA buffer must hold 16 samples,
+ * plus pre/post garbage samples.
+ */
+#define S626_DAC_WDMABUF_DWORDS 1 /*
+ * DAC output DMA buffer holds a single
+ * sample.
+ */
/* All remaining space in 4KB DMA buffer is available for the RPS1 program. */
@@ -95,60 +105,90 @@
#define S626_RPS_IRQ 0x60000000 /* IRQ */
#define S626_RPS_LOGICAL_OR 0x08000000 /* Logical OR conditionals. */
-#define S626_RPS_INVERT 0x04000000 /* Test for negated
- * semaphores. */
+#define S626_RPS_INVERT 0x04000000 /*
+ * Test for negated
+ * semaphores.
+ */
#define S626_RPS_DEBI 0x00000002 /* DEBI done */
-#define S626_RPS_SIG0 0x00200000 /* RPS semaphore 0
- * (used by ADC). */
-#define S626_RPS_SIG1 0x00400000 /* RPS semaphore 1
- * (used by DAC). */
-#define S626_RPS_SIG2 0x00800000 /* RPS semaphore 2
- * (not used). */
+#define S626_RPS_SIG0 0x00200000 /*
+ * RPS semaphore 0
+ * (used by ADC).
+ */
+#define S626_RPS_SIG1 0x00400000 /*
+ * RPS semaphore 1
+ * (used by DAC).
+ */
+#define S626_RPS_SIG2 0x00800000 /*
+ * RPS semaphore 2
+ * (not used).
+ */
#define S626_RPS_GPIO2 0x00080000 /* RPS GPIO2 */
#define S626_RPS_GPIO3 0x00100000 /* RPS GPIO3 */
-#define S626_RPS_SIGADC S626_RPS_SIG0 /* Trigger/status for
- * ADC's RPS program. */
-#define S626_RPS_SIGDAC S626_RPS_SIG1 /* Trigger/status for
- * DAC's RPS program. */
+#define S626_RPS_SIGADC S626_RPS_SIG0 /*
+ * Trigger/status for
+ * ADC's RPS program.
+ */
+#define S626_RPS_SIGDAC S626_RPS_SIG1 /*
+ * Trigger/status for
+ * DAC's RPS program.
+ */
/* RPS clock parameters. */
-#define S626_RPSCLK_SCALAR 8 /* This is apparent ratio of
- * PCI/RPS clks (undocumented!!). */
+#define S626_RPSCLK_SCALAR 8 /*
+ * This is apparent ratio of
+ * PCI/RPS clks (undocumented!!).
+ */
#define S626_RPSCLK_PER_US (33 / S626_RPSCLK_SCALAR)
- /* Number of RPS clocks in one
- * microsecond. */
+ /*
+ * Number of RPS clocks in one
+ * microsecond.
+ */
/* Event counter source addresses. */
#define S626_SBA_RPS_A0 0x27 /* Time of RPS0 busy, in PCI clocks. */
/* GPIO constants. */
-#define S626_GPIO_BASE 0x10004000 /* GPIO 0,2,3 = inputs,
- * GPIO3 = IRQ; GPIO1 = out. */
+#define S626_GPIO_BASE 0x10004000 /*
+ * GPIO 0,2,3 = inputs,
+ * GPIO3 = IRQ; GPIO1 = out.
+ */
#define S626_GPIO1_LO 0x00000000 /* GPIO1 set to LOW. */
#define S626_GPIO1_HI 0x00001000 /* GPIO1 set to HIGH. */
/* Primary Status Register (PSR) constants. */
#define S626_PSR_DEBI_E 0x00040000 /* DEBI event flag. */
#define S626_PSR_DEBI_S 0x00080000 /* DEBI status flag. */
-#define S626_PSR_A2_IN 0x00008000 /* Audio output DMA2 protection
- * address reached. */
-#define S626_PSR_AFOU 0x00000800 /* Audio FIFO under/overflow
- * detected. */
-#define S626_PSR_GPIO2 0x00000020 /* GPIO2 input pin: 0=AdcBusy,
- * 1=AdcIdle. */
-#define S626_PSR_EC0S 0x00000001 /* Event counter 0 threshold
- * reached. */
+#define S626_PSR_A2_IN 0x00008000 /*
+ * Audio output DMA2 protection
+ * address reached.
+ */
+#define S626_PSR_AFOU 0x00000800 /*
+ * Audio FIFO under/overflow
+ * detected.
+ */
+#define S626_PSR_GPIO2 0x00000020 /*
+ * GPIO2 input pin: 0=AdcBusy,
+ * 1=AdcIdle.
+ */
+#define S626_PSR_EC0S 0x00000001 /*
+ * Event counter 0 threshold
+ * reached.
+ */
/* Secondary Status Register (SSR) constants. */
-#define S626_SSR_AF2_OUT 0x00000200 /* Audio 2 output FIFO
- * under/overflow detected. */
+#define S626_SSR_AF2_OUT 0x00000200 /*
+ * Audio 2 output FIFO
+ * under/overflow detected.
+ */
/* Master Control Register 1 (MC1) constants. */
#define S626_MC1_SOFT_RESET 0x80000000 /* Invoke 7146 soft reset. */
-#define S626_MC1_SHUTDOWN 0x3FFF0000 /* Shut down all MC1-controlled
- * enables. */
+#define S626_MC1_SHUTDOWN 0x3FFF0000 /*
+ * Shut down all MC1-controlled
+ * enables.
+ */
#define S626_MC1_ERPS1 0x2000 /* Enab/disable RPS task 1. */
#define S626_MC1_ERPS0 0x1000 /* Enab/disable RPS task 0. */
@@ -177,15 +217,23 @@
#define S626_P_DEBIAD 0x0088 /* DEBI target address. */
#define S626_P_I2CCTRL 0x008C /* I2C control. */
#define S626_P_I2CSTAT 0x0090 /* I2C status. */
-#define S626_P_BASEA2_IN 0x00AC /* Audio input 2 base physical DMAbuf
- * address. */
-#define S626_P_PROTA2_IN 0x00B0 /* Audio input 2 physical DMAbuf
- * protection address. */
+#define S626_P_BASEA2_IN 0x00AC /*
+ * Audio input 2 base physical DMAbuf
+ * address.
+ */
+#define S626_P_PROTA2_IN 0x00B0 /*
+ * Audio input 2 physical DMAbuf
+ * protection address.
+ */
#define S626_P_PAGEA2_IN 0x00B4 /* Audio input 2 paging attributes. */
-#define S626_P_BASEA2_OUT 0x00B8 /* Audio output 2 base physical DMAbuf
- * address. */
-#define S626_P_PROTA2_OUT 0x00BC /* Audio output 2 physical DMAbuf
- * protection address. */
+#define S626_P_BASEA2_OUT 0x00B8 /*
+ * Audio output 2 base physical DMAbuf
+ * address.
+ */
+#define S626_P_PROTA2_OUT 0x00BC /*
+ * Audio output 2 physical DMAbuf
+ * protection address.
+ */
#define S626_P_PAGEA2_OUT 0x00C0 /* Audio output 2 paging attributes. */
#define S626_P_RPSPAGE0 0x00C4 /* RPS0 page. */
#define S626_P_RPSPAGE1 0x00C8 /* RPS1 page. */
@@ -205,8 +253,10 @@
#define S626_P_PSR 0x0110 /* Primary status. */
#define S626_P_SSR 0x0114 /* Secondary status. */
#define S626_P_EC1R 0x0118 /* Event counter set 1. */
-#define S626_P_ADP4 0x0138 /* Logical audio DMA pointer of audio
- * input FIFO A2_IN. */
+#define S626_P_ADP4 0x0138 /*
+ * Logical audio DMA pointer of audio
+ * input FIFO A2_IN.
+ */
#define S626_P_FB_BUFFER1 0x0144 /* Audio feedback buffer 1. */
#define S626_P_FB_BUFFER2 0x0148 /* Audio feedback buffer 2. */
#define S626_P_TSL1 0x0180 /* Audio time slot list 1. */
@@ -243,13 +293,19 @@
#define S626_LP_RDMISC2 0x0082 /* Read Misc2. */
/* Bit masks for MISC1 register that are the same for reads and writes. */
-#define S626_MISC1_WENABLE 0x8000 /* enab writes to MISC2 (except Clear
- * Watchdog bit). */
+#define S626_MISC1_WENABLE 0x8000 /*
+ * enab writes to MISC2 (except Clear
+ * Watchdog bit).
+ */
#define S626_MISC1_WDISABLE 0x0000 /* Disable writes to MISC2. */
-#define S626_MISC1_EDCAP 0x1000 /* Enable edge capture on DIO chans
- * specified by S626_LP_WRCAPSELx. */
-#define S626_MISC1_NOEDCAP 0x0000 /* Disable edge capture on specified
- * DIO chans. */
+#define S626_MISC1_EDCAP 0x1000 /*
+ * Enable edge capture on DIO chans
+ * specified by S626_LP_WRCAPSELx.
+ */
+#define S626_MISC1_NOEDCAP 0x0000 /*
+ * Disable edge capture on specified
+ * DIO chans.
+ */
/* Bit masks for MISC1 register reads. */
#define S626_RDMISC1_WDTIMEOUT 0x4000 /* Watchdog timer timed out. */
@@ -268,35 +324,49 @@
#define S626_A1_RUN 0x20000000 /* Run A1 based on TSL1. */
#define S626_A1_SWAP 0x00200000 /* Use big-endian for A1. */
#define S626_A2_SWAP 0x00100000 /* Use big-endian for A2. */
-#define S626_WS_MODES 0x00019999 /* WS0 = TSL1 trigger input,
- * WS1-WS4 = CS* outputs. */
-
-#if S626_PLATFORM == S626_INTEL /* Base ACON1 config: always run
- * A1 based on TSL1. */
+#define S626_WS_MODES 0x00019999 /*
+ * WS0 = TSL1 trigger input,
+ * WS1-WS4 = CS* outputs.
+ */
+
+#if S626_PLATFORM == S626_INTEL /*
+ * Base ACON1 config: always run
+ * A1 based on TSL1.
+ */
#define S626_ACON1_BASE (S626_WS_MODES | S626_A1_RUN)
#elif S626_PLATFORM == S626_MOTOROLA
#define S626_ACON1_BASE \
(S626_WS_MODES | S626_A1_RUN | S626_A1_SWAP | S626_A2_SWAP)
#endif
-#define S626_ACON1_ADCSTART S626_ACON1_BASE /* Start ADC: run A1
- * based on TSL1. */
+#define S626_ACON1_ADCSTART S626_ACON1_BASE /*
+ * Start ADC: run A1
+ * based on TSL1.
+ */
#define S626_ACON1_DACSTART (S626_ACON1_BASE | S626_A2_RUN)
/* Start transmit to DAC: run A2 based on TSL2. */
#define S626_ACON1_DACSTOP S626_ACON1_BASE /* Halt A2. */
/* Bit masks for ACON2 register. */
#define S626_A1_CLKSRC_BCLK1 0x00000000 /* A1 bit rate = BCLK1 (ADC). */
-#define S626_A2_CLKSRC_X1 0x00800000 /* A2 bit rate = ACLK/1
- * (DACs). */
-#define S626_A2_CLKSRC_X2 0x00C00000 /* A2 bit rate = ACLK/2
- * (DACs). */
-#define S626_A2_CLKSRC_X4 0x01400000 /* A2 bit rate = ACLK/4
- * (DACs). */
+#define S626_A2_CLKSRC_X1 0x00800000 /*
+ * A2 bit rate = ACLK/1
+ * (DACs).
+ */
+#define S626_A2_CLKSRC_X2 0x00C00000 /*
+ * A2 bit rate = ACLK/2
+ * (DACs).
+ */
+#define S626_A2_CLKSRC_X4 0x01400000 /*
+ * A2 bit rate = ACLK/4
+ * (DACs).
+ */
#define S626_INVERT_BCLK2 0x00100000 /* Invert BCLK2 (DACs). */
#define S626_BCLK2_OE 0x00040000 /* Enable BCLK2 (DACs). */
-#define S626_ACON2_XORMASK 0x000C0000 /* XOR mask for ACON2
- * active-low bits. */
+#define S626_ACON2_XORMASK 0x000C0000 /*
+ * XOR mask for ACON2
+ * active-low bits.
+ */
#define S626_ACON2_INIT (S626_ACON2_XORMASK ^ \
(S626_A1_CLKSRC_BCLK1 | S626_A2_CLKSRC_X2 | \
@@ -308,12 +378,18 @@
#define S626_WS3 0x10000000
#define S626_WS4 0x08000000
#define S626_RSD1 0x01000000 /* Shift A1 data in on SD1. */
-#define S626_SDW_A1 0x00800000 /* Store rcv'd char at next char
- * slot of DWORD1 buffer. */
-#define S626_SIB_A1 0x00400000 /* Store rcv'd char at next
- * char slot of FB1 buffer. */
-#define S626_SF_A1 0x00200000 /* Write unsigned long
- * buffer to input FIFO. */
+#define S626_SDW_A1 0x00800000 /*
+ * Store rcv'd char at next char
+ * slot of DWORD1 buffer.
+ */
+#define S626_SIB_A1 0x00400000 /*
+ * Store rcv'd char at next
+ * char slot of FB1 buffer.
+ */
+#define S626_SF_A1 0x00200000 /*
+ * Write unsigned long
+ * buffer to input FIFO.
+ */
/* Select parallel-to-serial converter's data source: */
#define S626_XFIFO_0 0x00000000 /* Data fifo byte 0. */
@@ -324,31 +400,45 @@
#define S626_XFB1 0x00000050 /* FB_BUFFER byte 1. */
#define S626_XFB2 0x00000060 /* FB_BUFFER byte 2. */
#define S626_XFB3 0x00000070 /* FB_BUFFER byte 3. */
-#define S626_SIB_A2 0x00000200 /* Store next dword from A2's
+#define S626_SIB_A2 0x00000200 /*
+ * Store next dword from A2's
* input shifter to FB2
- * buffer. */
-#define S626_SF_A2 0x00000100 /* Store next dword from A2's
+ * buffer.
+ */
+#define S626_SF_A2 0x00000100 /*
+ * Store next dword from A2's
* input shifter to its input
- * fifo. */
-#define S626_LF_A2 0x00000080 /* Load next dword from A2's
+ * fifo.
+ */
+#define S626_LF_A2 0x00000080 /*
+ * Load next dword from A2's
* output fifo into its
- * output dword buffer. */
+ * output dword buffer.
+ */
#define S626_XSD2 0x00000008 /* Shift data out on SD2. */
#define S626_RSD3 0x00001800 /* Shift data in on SD3. */
#define S626_RSD2 0x00001000 /* Shift data in on SD2. */
-#define S626_LOW_A2 0x00000002 /* Drive last SD low for 7 clks,
- * then tri-state. */
+#define S626_LOW_A2 0x00000002 /*
+ * Drive last SD low for 7 clks,
+ * then tri-state.
+ */
#define S626_EOS 0x00000001 /* End of superframe. */
/* I2C configuration constants. */
-#define S626_I2C_CLKSEL 0x0400 /* I2C bit rate =
- * PCIclk/480 = 68.75 KHz. */
-#define S626_I2C_BITRATE 68.75 /* I2C bus data bit rate
+#define S626_I2C_CLKSEL 0x0400 /*
+ * I2C bit rate =
+ * PCIclk/480 = 68.75 KHz.
+ */
+#define S626_I2C_BITRATE 68.75 /*
+ * I2C bus data bit rate
* (determined by
- * S626_I2C_CLKSEL) in KHz. */
-#define S626_I2C_WRTIME 15.0 /* Worst case time, in msec,
+ * S626_I2C_CLKSEL) in KHz.
+ */
+#define S626_I2C_WRTIME 15.0 /*
+ * Worst case time, in msec,
* for EEPROM internal write
- * op. */
+ * op.
+ */
/* I2C manifest constants. */
@@ -368,8 +458,10 @@
#define S626_I2C_B0(ATTR, VAL) (((ATTR) << 2) | ((VAL) << 8))
/* DEBI command constants. */
-#define S626_DEBI_CMD_SIZE16 (2 << 17) /* Transfer size is always
- * 2 bytes. */
+#define S626_DEBI_CMD_SIZE16 (2 << 17) /*
+ * Transfer size is always
+ * 2 bytes.
+ */
#define S626_DEBI_CMD_READ 0x00010000 /* Read operation. */
#define S626_DEBI_CMD_WRITE 0x00000000 /* Write operation. */
@@ -380,42 +472,58 @@
#define S626_DEBI_CMD_WRWORD (S626_DEBI_CMD_WRITE | S626_DEBI_CMD_SIZE16)
/* DEBI configuration constants. */
-#define S626_DEBI_CFG_XIRQ_EN 0x80000000 /* Enable external interrupt
- * on GPIO3. */
+#define S626_DEBI_CFG_XIRQ_EN 0x80000000 /*
+ * Enable external interrupt
+ * on GPIO3.
+ */
#define S626_DEBI_CFG_XRESUME 0x40000000 /* Resume block */
- /* Transfer when XIRQ
- * deasserted. */
+ /*
+ * Transfer when XIRQ
+ * deasserted.
+ */
#define S626_DEBI_CFG_TOQ 0x03C00000 /* Timeout (15 PCI cycles). */
#define S626_DEBI_CFG_FAST 0x10000000 /* Fast mode enable. */
/* 4-bit field that specifies DEBI timeout value in PCI clock cycles: */
-#define S626_DEBI_CFG_TOUT_BIT 22 /* Finish DEBI cycle after this many
- * clocks. */
+#define S626_DEBI_CFG_TOUT_BIT 22 /*
+ * Finish DEBI cycle after this many
+ * clocks.
+ */
/* 2-bit field that specifies Endian byte lane steering: */
-#define S626_DEBI_CFG_SWAP_NONE 0x00000000 /* Straight - don't swap any
- * bytes (Intel). */
+#define S626_DEBI_CFG_SWAP_NONE 0x00000000 /*
+ * Straight - don't swap any
+ * bytes (Intel).
+ */
#define S626_DEBI_CFG_SWAP_2 0x00100000 /* 2-byte swap (Motorola). */
#define S626_DEBI_CFG_SWAP_4 0x00200000 /* 4-byte swap. */
-#define S626_DEBI_CFG_SLAVE16 0x00080000 /* Slave is able to serve
- * 16-bit cycles. */
-#define S626_DEBI_CFG_INC 0x00040000 /* Enable address increment
- * for block transfers. */
+#define S626_DEBI_CFG_SLAVE16 0x00080000 /*
+ * Slave is able to serve
+ * 16-bit cycles.
+ */
+#define S626_DEBI_CFG_INC 0x00040000 /*
+ * Enable address increment
+ * for block transfers.
+ */
#define S626_DEBI_CFG_INTEL 0x00020000 /* Intel style local bus. */
#define S626_DEBI_CFG_TIMEROFF 0x00010000 /* Disable timer. */
#if S626_PLATFORM == S626_INTEL
-#define S626_DEBI_TOUT 7 /* Wait 7 PCI clocks (212 ns) before
- * polling RDY. */
+#define S626_DEBI_TOUT 7 /*
+ * Wait 7 PCI clocks (212 ns) before
+ * polling RDY.
+ */
/* Intel byte lane steering (pass through all byte lanes). */
#define S626_DEBI_SWAP S626_DEBI_CFG_SWAP_NONE
#elif S626_PLATFORM == S626_MOTOROLA
-#define S626_DEBI_TOUT 15 /* Wait 15 PCI clocks (454 ns) maximum
- * before timing out. */
+#define S626_DEBI_TOUT 15 /*
+ * Wait 15 PCI clocks (454 ns) maximum
+ * before timing out.
+ */
/* Motorola byte lane steering. */
#define S626_DEBI_SWAP S626_DEBI_CFG_SWAP_2
@@ -429,10 +537,14 @@
/* LoadSrc values: */
#define S626_LOADSRC_INDX 0 /* Preload core in response to Index. */
-#define S626_LOADSRC_OVER 1 /* Preload core in response to
- * Overflow. */
-#define S626_LOADSRCB_OVERA 2 /* Preload B core in response to
- * A Overflow. */
+#define S626_LOADSRC_OVER 1 /*
+ * Preload core in response to
+ * Overflow.
+ */
+#define S626_LOADSRCB_OVERA 2 /*
+ * Preload B core in response to
+ * A Overflow.
+ */
#define S626_LOADSRC_NONE 3 /* Never preload core. */
/* IntSrc values: */
@@ -469,10 +581,14 @@
#define S626_CNTSRC_SYSCLK_DOWN 3 /* System clock down */
/* ClkPol values: */
-#define S626_CLKPOL_POS 0 /* Counter/Extender clock is
- * active high. */
-#define S626_CLKPOL_NEG 1 /* Counter/Extender clock is
- * active low. */
+#define S626_CLKPOL_POS 0 /*
+ * Counter/Extender clock is
+ * active high.
+ */
+#define S626_CLKPOL_NEG 1 /*
+ * Counter/Extender clock is
+ * active low.
+ */
#define S626_CNTDIR_UP 0 /* Timer counts up. */
#define S626_CNTDIR_DOWN 1 /* Timer counts down. */
@@ -488,8 +604,10 @@
/* Sanity-check limits for parameters. */
-#define S626_NUM_COUNTERS 6 /* Maximum valid counter
- * logical channel number. */
+#define S626_NUM_COUNTERS 6 /*
+ * Maximum valid counter
+ * logical channel number.
+ */
#define S626_NUM_INTSOURCES 4
#define S626_NUM_LATCHSOURCES 4
#define S626_NUM_CLKMULTS 4
--
1.9.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH 1/1] Staging: comedi: s626: fix comment issue
2016-06-08 9:48 [PATCH 1/1] Staging: comedi: s626: fix comment issue Ravishankar Karkala Mallikarjunayya
@ 2016-06-08 10:00 ` Ian Abbott
0 siblings, 0 replies; 2+ messages in thread
From: Ian Abbott @ 2016-06-08 10:00 UTC (permalink / raw)
To: Ravishankar Karkala Mallikarjunayya, hsweeten, gregkh; +Cc: devel, linux-kernel
On 08/06/16 10:48, Ravishankar Karkala Mallikarjunayya wrote:
> This fixes up a WARNING: 'Block comments use a trailing */ on a
> separate line'found by the checkpatch.pl tool.
>
> Signed-off-by: Ravishankar Karkala Mallikarjunayya <ravishankarkm32@gmail.com>
> ---
> drivers/staging/comedi/drivers/s626.h | 356 ++++++++++++++++++++++------------
> 1 file changed, 237 insertions(+), 119 deletions(-)
Thanks!
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
--
-=( Ian Abbott @ MEV Ltd. E-mail: <abbotti@mev.co.uk> )=-
-=( Web: http://www.mev.co.uk/ )=-
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2016-06-08 10:00 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-08 9:48 [PATCH 1/1] Staging: comedi: s626: fix comment issue Ravishankar Karkala Mallikarjunayya
2016-06-08 10:00 ` Ian Abbott
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).