From: Vladimir Oltean <olteanv@gmail.com>
To: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: Jonathan McDowell <noodles@earth.li>,
Andrew Lunn <andrew@lunn.ch>,
Vivien Didelot <vivien.didelot@gmail.com>,
Florian Fainelli <f.fainelli@gmail.com>,
"David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>, netdev <netdev@vger.kernel.org>,
lkml <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/2] net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB
Date: Thu, 11 Jun 2020 12:01:25 +0300 [thread overview]
Message-ID: <CA+h21hqyAKucPENVANwuNo-UuCY0W3z8QF1FZ-nhd0uQ8tyC+w@mail.gmail.com> (raw)
In-Reply-To: <20200611085523.GV1551@shell.armlinux.org.uk>
Hi Russell,
On Thu, 11 Jun 2020 at 11:57, Russell King - ARM Linux admin
<linux@armlinux.org.uk> wrote:
>
>
> Alternatively, phylink supports polling mode, but due to the layered
> way DSA is written, DSA drivers don't have access to that as that is
> in the DSA upper levels in net/dsa/slave.c (dsa_slave_phy_setup(),
> it would be dp->pl_config.pcs_poll).
>
They do, see https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/tree/drivers/net/dsa/ocelot/felix.c#n606
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC for 0.8m (est. 1762m) line in suburbia: sync at 13.1Mbps down 503kbps up
Thanks,
-Vladimir
next prev parent reply other threads:[~2020-06-11 9:01 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-05 18:08 [PATCH 0/2] net: dsa: qca8k: Add SGMII configuration options Jonathan McDowell
2020-06-05 18:10 ` [PATCH 1/2] dt-bindings: net: dsa: qca8k: document SGMII properties Jonathan McDowell
2020-06-15 17:45 ` Rob Herring
2020-06-15 18:15 ` Jonathan McDowell
2020-06-05 18:10 ` [PATCH 2/2] net: dsa: qca8k: introduce SGMII configuration options Jonathan McDowell
2020-06-05 18:28 ` Marek Behun
2020-06-05 18:38 ` Andrew Lunn
2020-06-06 7:49 ` Jonathan McDowell
2020-06-06 8:37 ` Russell King - ARM Linux admin
2020-06-06 10:59 ` Jonathan McDowell
2020-06-06 13:43 ` Russell King - ARM Linux admin
2020-06-06 18:02 ` Jonathan McDowell
2020-06-06 14:03 ` Andrew Lunn
2020-06-08 18:39 ` [RFC PATCH v2] net: dsa: qca8k: Improve SGMII interface handling Jonathan McDowell
2020-06-08 19:10 ` Russell King - ARM Linux admin
2020-06-10 19:13 ` [RFC PATCH v3 0/2] " Jonathan McDowell
2020-06-10 19:14 ` [PATCH 1/2] net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB Jonathan McDowell
2020-06-11 3:15 ` Florian Fainelli
2020-06-11 8:55 ` Russell King - ARM Linux admin
2020-06-11 9:01 ` Vladimir Oltean [this message]
2020-06-12 11:53 ` Jonathan McDowell
2020-06-11 8:58 ` Vladimir Oltean
2020-06-11 11:04 ` Jonathan McDowell
2020-06-10 19:15 ` [PATCH 2/2] net: dsa: qca8k: Improve SGMII interface handling Jonathan McDowell
2020-06-11 3:31 ` Florian Fainelli
2020-06-11 17:47 ` Jonathan McDowell
2020-06-11 8:58 ` Russell King - ARM Linux admin
2020-06-10 23:29 ` [RFC PATCH v3 0/2] " David Miller
2020-06-13 11:31 ` [RFC PATCH v4 " Jonathan McDowell
2020-06-13 11:31 ` [RFC PATCH v4 1/2] net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB Jonathan McDowell
2020-06-13 19:30 ` Vladimir Oltean
2020-06-13 11:32 ` [RFC PATCH v4 2/2] net: dsa: qca8k: Improve SGMII interface handling Jonathan McDowell
2020-06-13 20:10 ` Vladimir Oltean
2020-06-14 17:20 ` Jonathan McDowell
2020-06-20 10:30 ` [PATCH net-next v5 0/3] " Jonathan McDowell
2020-06-20 10:30 ` [PATCH net-next v5 1/3] net: dsa: qca8k: Switch to PHYLINK instead of PHYLIB Jonathan McDowell
2020-06-20 10:31 ` [PATCH net-next v5 2/3] net: dsa: qca8k: Improve SGMII interface handling Jonathan McDowell
2020-06-20 10:31 ` [PATCH net-next v5 3/3] net: dsa: qca8k: Minor comment spelling fix Jonathan McDowell
2020-06-22 22:54 ` [PATCH net-next v5 0/3] net: dsa: qca8k: Improve SGMII interface handling David Miller
2020-06-19 8:12 ` [PATCH 2/2] net: dsa: qca8k: introduce SGMII configuration options Dan Carpenter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CA+h21hqyAKucPENVANwuNo-UuCY0W3z8QF1FZ-nhd0uQ8tyC+w@mail.gmail.com \
--to=olteanv@gmail.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=f.fainelli@gmail.com \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=netdev@vger.kernel.org \
--cc=noodles@earth.li \
--cc=vivien.didelot@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).