* [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
@ 2019-02-18 13:03 Vinod Koul
2019-02-18 13:33 ` Andrew Lunn
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Vinod Koul @ 2019-02-18 13:03 UTC (permalink / raw)
To: David S Miller
Cc: linux-arm-msm, Bjorn Andersson, Vinod Koul, netdev,
Niklas Cassel, Andrew Lunn, Florian Fainelli,
Michal Vokáč
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
drivers/net/dsa/qca8k.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index a4b6cda38016..aa1f7f1b20d3 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -443,6 +443,18 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
val = QCA8K_PORT_PAD_RGMII_EN;
qca8k_write(priv, reg, val);
break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ /* RGMII_ID needs internal delay. This is enabled through
+ * PORT5_PAD_CTRL for all ports, rather than individual port
+ * registers
+ */
+ qca8k_write(priv, reg,
+ QCA8K_PORT_PAD_RGMII_EN |
+ QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
+ break;
case PHY_INTERFACE_MODE_SGMII:
qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
break;
--
2.20.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
2019-02-18 13:03 [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode Vinod Koul
@ 2019-02-18 13:33 ` Andrew Lunn
2019-02-19 4:59 ` Vinod Koul
2019-02-18 13:35 ` Michal Vokáč
2019-02-18 13:36 ` Andrew Lunn
2 siblings, 1 reply; 6+ messages in thread
From: Andrew Lunn @ 2019-02-18 13:33 UTC (permalink / raw)
To: Vinod Koul
Cc: David S Miller, linux-arm-msm, Bjorn Andersson, netdev,
Niklas Cassel, Florian Fainelli, Michal Vokáč
On Mon, Feb 18, 2019 at 06:33:51PM +0530, Vinod Koul wrote:
> RGMII_ID specifies that we should have internal delay, so resurrect the
> delay addition routine but under the RGMII_ID mode.
>
> Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> drivers/net/dsa/qca8k.c | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> index a4b6cda38016..aa1f7f1b20d3 100644
> --- a/drivers/net/dsa/qca8k.c
> +++ b/drivers/net/dsa/qca8k.c
> @@ -443,6 +443,18 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
> val = QCA8K_PORT_PAD_RGMII_EN;
> qca8k_write(priv, reg, val);
> break;
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + /* RGMII_ID needs internal delay. This is enabled through
> + * PORT5_PAD_CTRL for all ports, rather than individual port
> + * registers
> + */
> + qca8k_write(priv, reg,
> + QCA8K_PORT_PAD_RGMII_EN |
> + QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
> + QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
> + qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
> + QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
> + break;
Hi Vinod
So i'm still confused if this is global, or per-port. The first
register written looks to be per-port, although only for ports 0 and
6. The second write seems to be global.
Is there a danger that port 0 has PHY_INTERFACE_MODE_RGMII_ID and port
6 has PHY_INTERFACE_MODE_RGMII, and we end up with delays disabled?
Maybe we should try to detect this, and return an error?
> case PHY_INTERFACE_MODE_SGMII:
> qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
> break;
I think it would be good to add the other two PHY_INTERFACE_MODE_RGMII
modes to the default clause so we get an error reported that they are
not implemented.
Andrew
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
2019-02-18 13:03 [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode Vinod Koul
2019-02-18 13:33 ` Andrew Lunn
@ 2019-02-18 13:35 ` Michal Vokáč
2019-02-18 13:36 ` Andrew Lunn
2 siblings, 0 replies; 6+ messages in thread
From: Michal Vokáč @ 2019-02-18 13:35 UTC (permalink / raw)
To: Vinod Koul, David S Miller
Cc: linux-arm-msm, Bjorn Andersson, netdev, Niklas Cassel,
Andrew Lunn, Florian Fainelli
On 18. 02. 19 14:03, Vinod Koul wrote:
> RGMII_ID specifies that we should have internal delay, so resurrect the
> delay addition routine but under the RGMII_ID mode.
>
> Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes the problem on my imx6dl platform with QCA8334 switch.
Thank you!
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> drivers/net/dsa/qca8k.c | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> index a4b6cda38016..aa1f7f1b20d3 100644
> --- a/drivers/net/dsa/qca8k.c
> +++ b/drivers/net/dsa/qca8k.c
> @@ -443,6 +443,18 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
> val = QCA8K_PORT_PAD_RGMII_EN;
> qca8k_write(priv, reg, val);
> break;
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + /* RGMII_ID needs internal delay. This is enabled through
> + * PORT5_PAD_CTRL for all ports, rather than individual port
> + * registers
> + */
> + qca8k_write(priv, reg,
> + QCA8K_PORT_PAD_RGMII_EN |
> + QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
> + QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
> + qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
> + QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
> + break;
> case PHY_INTERFACE_MODE_SGMII:
> qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
> break;
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
2019-02-18 13:03 [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode Vinod Koul
2019-02-18 13:33 ` Andrew Lunn
2019-02-18 13:35 ` Michal Vokáč
@ 2019-02-18 13:36 ` Andrew Lunn
2019-02-19 5:00 ` Vinod Koul
2 siblings, 1 reply; 6+ messages in thread
From: Andrew Lunn @ 2019-02-18 13:36 UTC (permalink / raw)
To: Vinod Koul
Cc: David S Miller, linux-arm-msm, Bjorn Andersson, netdev,
Niklas Cassel, Florian Fainelli, Michal Vokáč
On Mon, Feb 18, 2019 at 06:33:51PM +0530, Vinod Koul wrote:
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + /* RGMII_ID needs internal delay. This is enabled through
> + * PORT5_PAD_CTRL for all ports, rather than individual port
> + * registers
> + */
> + qca8k_write(priv, reg,
> + QCA8K_PORT_PAD_RGMII_EN |
> + QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
> + QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
Hi Vinod
Could you add some #defines for the delay values?
Thanks
Andrew
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
2019-02-18 13:33 ` Andrew Lunn
@ 2019-02-19 4:59 ` Vinod Koul
0 siblings, 0 replies; 6+ messages in thread
From: Vinod Koul @ 2019-02-19 4:59 UTC (permalink / raw)
To: Andrew Lunn
Cc: David S Miller, linux-arm-msm, Bjorn Andersson, netdev,
Niklas Cassel, Florian Fainelli, Michal Vokáč
Hi Andrew,
On 18-02-19, 14:33, Andrew Lunn wrote:
> On Mon, Feb 18, 2019 at 06:33:51PM +0530, Vinod Koul wrote:
> > RGMII_ID specifies that we should have internal delay, so resurrect the
> > delay addition routine but under the RGMII_ID mode.
> >
> > Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
> > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > drivers/net/dsa/qca8k.c | 12 ++++++++++++
> > 1 file changed, 12 insertions(+)
> >
> > diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> > index a4b6cda38016..aa1f7f1b20d3 100644
> > --- a/drivers/net/dsa/qca8k.c
> > +++ b/drivers/net/dsa/qca8k.c
> > @@ -443,6 +443,18 @@ qca8k_set_pad_ctrl(struct qca8k_priv *priv, int port, int mode)
> > val = QCA8K_PORT_PAD_RGMII_EN;
> > qca8k_write(priv, reg, val);
> > break;
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + /* RGMII_ID needs internal delay. This is enabled through
> > + * PORT5_PAD_CTRL for all ports, rather than individual port
> > + * registers
> > + */
> > + qca8k_write(priv, reg,
> > + QCA8K_PORT_PAD_RGMII_EN |
> > + QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
> > + QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
> > + qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
> > + QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
> > + break;
>
> Hi Vinod
>
> So i'm still confused if this is global, or per-port. The first
> register written looks to be per-port, although only for ports 0 and
> 6. The second write seems to be global.
This is still a global write which enables the delay in all the ports
(as was the case previously)
> Is there a danger that port 0 has PHY_INTERFACE_MODE_RGMII_ID and port
> 6 has PHY_INTERFACE_MODE_RGMII, and we end up with delays disabled?
> Maybe we should try to detect this, and return an error?
If that was the case, I would presume people would have reported an
issue that it doesn't work for them..?
> > case PHY_INTERFACE_MODE_SGMII:
> > qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
> > break;
>
> I think it would be good to add the other two PHY_INTERFACE_MODE_RGMII
> modes to the default clause so we get an error reported that they are
> not implemented.
That is still the case:
default:
pr_err("xMII mode %d not supported\n", mode);
return -EINVAL;
--
~Vinod
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode
2019-02-18 13:36 ` Andrew Lunn
@ 2019-02-19 5:00 ` Vinod Koul
0 siblings, 0 replies; 6+ messages in thread
From: Vinod Koul @ 2019-02-19 5:00 UTC (permalink / raw)
To: Andrew Lunn
Cc: David S Miller, linux-arm-msm, Bjorn Andersson, netdev,
Niklas Cassel, Florian Fainelli, Michal Vokáč
On 18-02-19, 14:36, Andrew Lunn wrote:
> On Mon, Feb 18, 2019 at 06:33:51PM +0530, Vinod Koul wrote:
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + /* RGMII_ID needs internal delay. This is enabled through
> > + * PORT5_PAD_CTRL for all ports, rather than individual port
> > + * registers
> > + */
> > + qca8k_write(priv, reg,
> > + QCA8K_PORT_PAD_RGMII_EN |
> > + QCA8K_PORT_PAD_RGMII_TX_DELAY(3) |
> > + QCA8K_PORT_PAD_RGMII_RX_DELAY(3));
>
> Hi Vinod
>
> Could you add some #defines for the delay values?
Sure will update the patch
--
~Vinod
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2019-02-19 5:00 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-02-18 13:03 [PATCH] net: dsa: qca8k: Enable delay for RGMII_ID mode Vinod Koul
2019-02-18 13:33 ` Andrew Lunn
2019-02-19 4:59 ` Vinod Koul
2019-02-18 13:35 ` Michal Vokáč
2019-02-18 13:36 ` Andrew Lunn
2019-02-19 5:00 ` Vinod Koul
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).