From: Andrew Lunn <andrew@lunn.ch>
To: Shannon Nelson <snelson@pensando.io>
Cc: netdev@vger.kernel.org
Subject: Re: [PATCH v3 net-next 13/19] ionic: Add initial ethtool support
Date: Fri, 19 Jul 2019 21:07:15 +0200 [thread overview]
Message-ID: <20190719190715.GO25635@lunn.ch> (raw)
In-Reply-To: <15796ade-68dd-4350-e481-3a3a1e7ce3d5@pensando.io>
On Fri, Jul 19, 2019 at 11:41:28AM -0700, Shannon Nelson wrote:
> On 7/18/19 7:40 PM, Andrew Lunn wrote:
> >On Thu, Jul 18, 2019 at 05:12:07PM -0700, Shannon Nelson wrote:
> >>On 7/17/19 8:28 PM, Andrew Lunn wrote:
> >>>On Fri, Jul 12, 2019 at 10:16:31PM -0700, Shannon Nelson wrote:
> >>>>On 7/8/19 7:14 PM, Andrew Lunn wrote:
> >>>>>>+static int ionic_set_pauseparam(struct net_device *netdev,
> >>>>>>+ struct ethtool_pauseparam *pause)
> >>>>>>+{
> >>>>>>+ struct lif *lif = netdev_priv(netdev);
> >>>>>>+ struct ionic *ionic = lif->ionic;
> >>>>>>+ struct ionic_dev *idev = &lif->ionic->idev;
> >>>>>>+
> >>>>>>+ u32 requested_pause;
> >>>>>>+ u32 cur_autoneg;
> >>>>>>+ int err;
> >>>>>>+
> >>>>>>+ cur_autoneg = idev->port_info->config.an_enable ? AUTONEG_ENABLE :
> >>>>>>+ AUTONEG_DISABLE;
> >>>>>>+ if (pause->autoneg != cur_autoneg) {
> >>>>>>+ netdev_info(netdev, "Please use 'ethtool -s ...' to change autoneg\n");
> >>>>>>+ return -EOPNOTSUPP;
> >>>>>>+ }
> >>>>>>+
> >>>>>>+ /* change both at the same time */
> >>>>>>+ requested_pause = PORT_PAUSE_TYPE_LINK;
> >>>>>>+ if (pause->rx_pause)
> >>>>>>+ requested_pause |= IONIC_PAUSE_F_RX;
> >>>>>>+ if (pause->tx_pause)
> >>>>>>+ requested_pause |= IONIC_PAUSE_F_TX;
> >>>>>>+
> >>>>>>+ if (requested_pause == idev->port_info->config.pause_type)
> >>>>>>+ return 0;
> >>>>>>+
> >>>>>>+ idev->port_info->config.pause_type = requested_pause;
> >>>>>>+
> >>>>>>+ mutex_lock(&ionic->dev_cmd_lock);
> >>>>>>+ ionic_dev_cmd_port_pause(idev, requested_pause);
> >>>>>>+ err = ionic_dev_cmd_wait(ionic, devcmd_timeout);
> >>>>>>+ mutex_unlock(&ionic->dev_cmd_lock);
> >>>>>>+ if (err)
> >>>>>>+ return err;
> >>>>>Hi Shannon
> >>>>>
> >>>>>I've no idea what the firmware black box is doing, but this looks
> >>>>>wrong.
> >>>>>
> >>>>>pause->autoneg is about if the results of auto-neg should be used or
> >>>>>not. If false, just configure the MAC with the pause settings and you
> >>>>>are done. If the interface is being forced, so autoneg in general is
> >>>>>disabled, just configure the MAC and you are done.
> >>>>>
> >>>>>If pause->autoneg is true and the interface is using auto-neg as a
> >>>>>whole, you pass the pause values to the PHY for it to advertise and
> >>>>>trigger an auto-neg. Once autoneg has completed, and the resolved
> >>>>>settings are available, the MAC is configured with the resolved
> >>>>>values.
> >>>>>
> >>>>>Looking at this code, i don't see any difference between configuring
> >>>>>the MAC or configuring the PHY. I would expect pause->autoneg to be
> >>>>>part of requested_pause somehow, so the firmware knows what is should
> >>>>>do.
> >>>>>
> >>>>> Andrew
> >>>>In this device there's actually very little the driver can do to directly
> >>>>configure the mac or phy besides passing through to the firmware what the
> >>>>user has requested - that happens here for the pause values, and in
> >>>>ionic_set_link_ksettings() for autoneg. The firmware is managing the port
> >>>>based on these requests with the help of internally configured rules defined
> >>>>in a customer setting.
> >>>I get that. But the firmware needs to conform to what Linux
> >>>expects. And what i see here does not conform. That is why i gave a
> >>>bit of detail in my reply.
> >>>
> >>>What exactly does the firmware do? Once we know that, we can figure
> >>>out when the driver should return -EOPNOTSUPP because of firmware
> >>>limitations, and what it can configure and should return 0.
> >>Because this is fairly smart FW, it handles this as expected. I can add
> >>this as another comment in the code.
> >Hi Shannon
> >
> >Looking at the code, i don't see how it can handle this
> >correctly. Please look at my comments, particularly the meaning of
> >pause->autoneg and describe how the firmware does the right thing,
> >given what information it is passed.
> >
>
> I guess I'm not sure how much better I can answer your question. Like
> several other devices, we don't support selecting pause->autoneg. The
> firmware manages the PHY itself, the driver doesn't have direct access to
> the PHY. The driver passes the tx and rx pause info down to the firmware in
> a command request. The NIC firmware does an autoneg if autoneg is enabled
> on the port.
Hi Shannon
Thanks. That was the information i was looking for.
Please return -EOPNOTSUPP if pause->autoneg indicates autoneg results
should not be used. Your firmware does not support it, so the driver
should error out. Also the get function should use a hard coded value
for pause->autoneg.
If you ever fix your firmware, you can add full support for pause
configuration.
Thanks
Andrew
next prev parent reply other threads:[~2019-07-19 19:07 UTC|newest]
Thread overview: 56+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-08 19:25 [PATCH v3 net-next 00/19] Add ionic driver Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 01/19] ionic: Add basic framework for IONIC Network device driver Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 02/19] ionic: Add hardware init and device commands Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 03/19] ionic: Add port management commands Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 04/19] ionic: Add basic lif support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 05/19] ionic: Add interrupts and doorbells Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 06/19] ionic: Add basic adminq support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 07/19] ionic: Add adminq action Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 08/19] ionic: Add notifyq support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 09/19] ionic: Add the basic NDO callbacks for netdev support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 10/19] ionic: Add management of rx filters Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 11/19] ionic: Add Rx filter and rx_mode ndo support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 12/19] ionic: Add async link status check and basic stats Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 13/19] ionic: Add initial ethtool support Shannon Nelson
2019-07-08 22:04 ` Andrew Lunn
2019-07-09 5:15 ` Michal Kubecek
2019-07-09 22:35 ` Shannon Nelson
2019-07-11 19:10 ` Shannon Nelson
2019-07-09 2:14 ` Andrew Lunn
2019-07-13 5:16 ` Shannon Nelson
2019-07-18 3:28 ` Andrew Lunn
2019-07-19 0:12 ` Shannon Nelson
2019-07-19 2:40 ` Andrew Lunn
2019-07-19 18:41 ` Shannon Nelson
2019-07-19 19:07 ` Andrew Lunn [this message]
2019-07-19 20:20 ` Shannon Nelson
2019-07-09 2:27 ` Andrew Lunn
2019-07-09 22:42 ` Shannon Nelson
2019-07-18 3:21 ` Andrew Lunn
2019-07-18 17:05 ` Shannon Nelson
2019-07-18 17:28 ` Andrew Lunn
2019-07-18 17:54 ` Shannon Nelson
2019-07-09 2:30 ` Andrew Lunn
2019-07-13 5:32 ` Shannon Nelson
2019-07-18 3:31 ` Andrew Lunn
2019-07-18 17:14 ` Shannon Nelson
2019-07-09 5:25 ` Michal Kubecek
2019-07-09 22:34 ` Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 14/19] ionic: Add Tx and Rx handling Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 15/19] ionic: Add netdev-event handling Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 16/19] ionic: Add driver stats Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 17/19] ionic: Add RSS support Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 18/19] ionic: Add coalesce and other features Shannon Nelson
2019-07-08 19:25 ` [PATCH v3 net-next 19/19] ionic: Add basic devlink interface Shannon Nelson
2019-07-08 19:34 ` Jiri Pirko
2019-07-08 19:58 ` Shannon Nelson
2019-07-08 20:03 ` Jiri Pirko
2019-07-08 22:58 ` Shannon Nelson
2019-07-09 6:56 ` Jiri Pirko
2019-07-09 19:13 ` Shannon Nelson
2019-07-10 6:48 ` Jiri Pirko
2019-07-10 17:06 ` Shannon Nelson
2019-07-09 1:26 ` Jakub Kicinski
2019-07-09 19:06 ` Shannon Nelson
2019-07-09 2:58 ` [PATCH v3 net-next 00/19] Add ionic driver David Miller
2019-07-09 3:01 ` Shannon Nelson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190719190715.GO25635@lunn.ch \
--to=andrew@lunn.ch \
--cc=netdev@vger.kernel.org \
--cc=snelson@pensando.io \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).