[PATCH v5 0/4] Add samsung-matisselte and common matisse dtsi

[PATCH v5 0/4] Add samsung-matisselte and common matisse dtsi

[Stefan Hansson]

This series adds a common samsung-matisse dtsi and reworks
samsung-matisse-wifi to use it, and introduces samsung-matisselte. I
choose matisselte over matisse-lte as this is how most other devices
(klte, s3ve3g) do it and it is the codename that Samsung gave the
device. See individual commits for more information.

---
Changes since v1:

 - Rebased on latest linux-next
 - Added qcom,msm8226 compatible to matisselte inspired by recent Lumia
   830 patch. This is done as in v1, the patch was rejected because I
   included the msm8226 dtsi despite not marking matisselte as
   compatible with msm8226, and I was not sure how to resolve that. As
   such, I'm copying what was done in the Lumia 830 (microsoft-tesla)
   patch given that it was accepted.

Changes since v2:

 - Updated commit message for UART patch to explain why it was added.
 - Gave more flags to git to provide a hopefully more readable patch.

Changes since v3:

 - Collect tags.
 - Remove spurious copyright notice.
 - Miscellaneous fixes following review feedback.

Changes since v4:

 - Collect tags.
 - Enable SD card support on matisselte.

Stefan Hansson (4):
  ARM: dts: qcom: samsung-matisse-common: Add initial common device tree
  dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE
  ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 LTE
    (SM-T535)
  ARM: dts: qcom: samsung-matisse-common: Add UART

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm/boot/dts/qcom/Makefile               |   1 +
 .../qcom-apq8026-samsung-matisse-wifi.dts     | 603 +++---------------
 ... qcom-msm8226-samsung-matisse-common.dtsi} |  68 +-
 .../qcom/qcom-msm8926-samsung-matisselte.dts  |  37 ++
 5 files changed, 126 insertions(+), 584 deletions(-)
 rewrite arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts (85%)
 copy arch/arm/boot/dts/qcom/{qcom-apq8026-samsung-matisse-wifi.dts => qcom-msm8226-samsung-matisse-common.dtsi} (86%)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts

-- 
2.41.0

[PATCH v5 1/4] ARM: dts: qcom: samsung-matisse-common: Add initial common device tree

[Stefan Hansson]

According to the dts from the kernel source code released by Samsung,
matissewifi and matisselte only have minor differences in hardware, so
use a shared dtsi to reduce duplicated code. Additionally, this should
make adding support for matisse3g easier should someone want to do that
at a later point.

As such, add a common device tree for all matisse devices by Samsung
based on the matissewifi dts. Support for matisselte will be introduced
in a later patch in this series and will use the common dtsi as well.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../qcom-apq8026-samsung-matisse-wifi.dts     | 595 +++---------------
 ... qcom-msm8226-samsung-matisse-common.dtsi} |  66 --
 2 files changed, 76 insertions(+), 585 deletions(-)
 rewrite arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts (85%)
 copy arch/arm/boot/dts/qcom/{qcom-apq8026-samsung-matisse-wifi.dts => qcom-msm8226-samsung-matisse-common.dtsi} (86%)

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
dissimilarity index 85%
index f516e0426bb9..b0da51f67539 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -1,519 +1,76 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
- */
-
-/dts-v1/;
-
-#include <dt-bindings/input/input.h>
-#include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
-
-/delete-node/ &adsp_region;
-/delete-node/ &smem_region;
-
-/ {
-	model = "Samsung Galaxy Tab 4 10.1";
-	compatible = "samsung,matisse-wifi", "qcom,apq8026";
-	chassis-type = "tablet";
-
-	aliases {
-		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
-		mmc1 = &sdhc_2; /* SDC2 SD card slot */
-		display0 = &framebuffer0;
-	};
-
-	chosen {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		stdout-path = "display0";
-
-		framebuffer0: framebuffer@3200000 {
-			compatible = "simple-framebuffer";
-			reg = <0x03200000 0x800000>;
-			width = <1280>;
-			height = <800>;
-			stride = <(1280 * 3)>;
-			format = "r8g8b8";
-		};
-	};
-
-	gpio-hall-sensor {
-		compatible = "gpio-keys";
-
-		event-hall-sensor {
-			label = "Hall Effect Sensor";
-			gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_LID>;
-			debounce-interval = <15>;
-			linux,can-disable;
-			wakeup-source;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		key-home {
-			label = "Home";
-			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOMEPAGE>;
-			debounce-interval = <15>;
-		};
-
-		key-volume-down {
-			label = "Volume Down";
-			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <15>;
-		};
-
-		key-volume-up {
-			label = "Volume Up";
-			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <15>;
-		};
-	};
-
-	i2c-backlight {
-		compatible = "i2c-gpio";
-		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-
-		pinctrl-0 = <&backlight_i2c_default_state>;
-		pinctrl-names = "default";
-
-		i2c-gpio,delay-us = <4>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		backlight@2c {
-			compatible = "ti,lp8556";
-			reg = <0x2c>;
-
-			dev-ctrl = /bits/ 8 <0x80>;
-			init-brt = /bits/ 8 <0x3f>;
-
-			pwms = <&backlight_pwm 0 100000>;
-			pwm-names = "lp8556";
-
-			rom-a0h {
-				rom-addr = /bits/ 8 <0xa0>;
-				rom-val = /bits/ 8 <0x44>;
-			};
-
-			rom-a1h {
-				rom-addr = /bits/ 8 <0xa1>;
-				rom-val = /bits/ 8 <0x6c>;
-			};
-
-			rom-a5h {
-				rom-addr = /bits/ 8 <0xa5>;
-				rom-val = /bits/ 8 <0x24>;
-			};
-		};
-	};
-
-	backlight_pwm: pwm {
-		compatible = "clk-pwm";
-		#pwm-cells = <2>;
-		clocks = <&mmcc CAMSS_GP0_CLK>;
-		pinctrl-0 = <&backlight_pwm_default_state>;
-		pinctrl-names = "default";
-	};
-
-	reg_tsp_1p8v: regulator-tsp-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "tsp_1p8v";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_en_default_state>;
-	};
-
-	reg_tsp_3p3v: regulator-tsp-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "tsp_3p3v";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_en1_default_state>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		framebuffer@3200000 {
-			reg = <0x03200000 0x800000>;
-			no-map;
-		};
-
-		mpss@8400000 {
-			reg = <0x08400000 0x1f00000>;
-			no-map;
-		};
-
-		mba@a300000 {
-			reg = <0x0a300000 0x100000>;
-			no-map;
-		};
-
-		reserved@cb00000 {
-			reg = <0x0cb00000 0x700000>;
-			no-map;
-		};
-
-		wcnss@d200000 {
-			reg = <0x0d200000 0x700000>;
-			no-map;
-		};
-
-		adsp_region: adsp@d900000 {
-			reg = <0x0d900000 0x1800000>;
-			no-map;
-		};
-
-		venus@f100000 {
-			reg = <0x0f100000 0x500000>;
-			no-map;
-		};
-
-		smem_region: smem@fa00000 {
-			reg = <0x0fa00000 0x100000>;
-			no-map;
-		};
-
-		reserved@fb00000 {
-			reg = <0x0fb00000 0x260000>;
-			no-map;
-		};
-
-		rfsa@fd60000 {
-			reg = <0x0fd60000 0x20000>;
-			no-map;
-		};
-
-		rmtfs@fd80000 {
-			compatible = "qcom,rmtfs-mem";
-			reg = <0x0fd80000 0x180000>;
-			no-map;
-
-			qcom,client-id = <1>;
-		};
-	};
-};
-
-&adsp {
-	status = "okay";
-};
-
-&blsp1_i2c2 {
-	status = "okay";
-
-	accelerometer@1d {
-		compatible = "st,lis2hh12";
-		reg = <0x1d>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&accel_int_default_state>;
-
-		st,drdy-int-pin = <1>;
-
-		vdd-supply = <&pm8226_l19>;
-		vddio-supply = <&pm8226_lvs1>;
-	};
-};
-
-&blsp1_i2c4 {
-	status = "okay";
-
-	muic: usb-switch@25 {
-		compatible = "siliconmitus,sm5502-muic";
-		reg = <0x25>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&muic_int_default_state>;
-	};
-};
-
-&blsp1_i2c5 {
-	status = "okay";
-
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_int_rst_default_state>;
-
-		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
-
-		vdd-supply = <&reg_tsp_1p8v>;
-		vdda-supply = <&reg_tsp_3p3v>;
-	};
-};
-
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-pm8226-regulators";
-
-		pm8226_s3: s3 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		pm8226_s4: s4 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_s5: s5 {
-			regulator-min-microvolt = <1150000>;
-			regulator-max-microvolt = <1150000>;
-		};
-
-		pm8226_l1: l1 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1225000>;
-		};
-
-		pm8226_l2: l2 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l3: l3 {
-			regulator-min-microvolt = <750000>;
-			regulator-max-microvolt = <1337500>;
-			regulator-always-on;
-		};
-
-		pm8226_l4: l4 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l5: l5 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l6: l6 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		pm8226_l7: l7 {
-			regulator-min-microvolt = <1850000>;
-			regulator-max-microvolt = <1850000>;
-		};
-
-		pm8226_l8: l8 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		pm8226_l9: l9 {
-			regulator-min-microvolt = <2050000>;
-			regulator-max-microvolt = <2050000>;
-		};
-
-		pm8226_l10: l10 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l12: l12 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l14: l14 {
-			regulator-min-microvolt = <2750000>;
-			regulator-max-microvolt = <2750000>;
-		};
-
-		pm8226_l15: l15 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		pm8226_l16: l16 {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3350000>;
-		};
-
-		pm8226_l17: l17 {
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-
-			regulator-system-load = <200000>;
-			regulator-allow-set-load;
-			regulator-always-on;
-		};
-
-		pm8226_l18: l18 {
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_l19: l19 {
-			regulator-min-microvolt = <2850000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		pm8226_l20: l20 {
-			regulator-min-microvolt = <3075000>;
-			regulator-max-microvolt = <3075000>;
-		};
-
-		pm8226_l21: l21 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_l22: l22 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		pm8226_l23: l23 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		pm8226_l24: l24 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1350000>;
-		};
-
-		pm8226_l25: l25 {
-			regulator-min-microvolt = <1775000>;
-			regulator-max-microvolt = <2125000>;
-		};
-
-		pm8226_l26: l26 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		pm8226_l27: l27 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l28: l28 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_lvs1: lvs1 {};
-	};
-};
-
-&sdhc_1 {
-	vmmc-supply = <&pm8226_l17>;
-	vqmmc-supply = <&pm8226_l6>;
-
-	bus-width = <8>;
-	non-removable;
-
-	status = "okay";
-};
-
-&sdhc_2 {
-	vmmc-supply = <&pm8226_l18>;
-	vqmmc-supply = <&pm8226_l21>;
-
-	bus-width = <4>;
-	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
-
-	status = "okay";
-};
-
-&tlmm {
-	accel_int_default_state: accel-int-default-state {
-		pins = "gpio54";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	backlight_i2c_default_state: backlight-i2c-default-state {
-		pins = "gpio20", "gpio21";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	backlight_pwm_default_state: backlight-pwm-default-state {
-		pins = "gpio33";
-		function = "gp0_clk";
-	};
-
-	muic_int_default_state: muic-int-default-state {
-		pins = "gpio67";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_en_default_state: tsp-en-default-state {
-		pins = "gpio31";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_en1_default_state: tsp-en1-default-state {
-		pins = "gpio73";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_int_rst_default_state: tsp-int-rst-default-state {
-		pins = "gpio17";
-		function = "gpio";
-		drive-strength = <10>;
-		bias-pull-up;
-	};
-};
-
-&usb {
-	extcon = <&muic>, <&muic>;
-	status = "okay";
-};
-
-&usb_hs_phy {
-	extcon = <&muic>;
-	v1p8-supply = <&pm8226_l10>;
-	v3p3-supply = <&pm8226_l20>;
-};
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1";
+	compatible = "samsung,matisse-wifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default_state>;
+
+		st,drdy-int-pin = <1>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+
+		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&reg_tsp_1p8v>;
+		vdda-supply = <&reg_tsp_3p3v>;
+	};
+};
+
+&tlmm {
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio73";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
similarity index 86%
copy from arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
copy to arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
index f516e0426bb9..ef98d88927ca 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -3,8 +3,6 @@
  * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
  */
 
-/dts-v1/;
-
 #include <dt-bindings/input/input.h>
 #include "qcom-msm8226.dtsi"
 #include "qcom-pm8226.dtsi"
@@ -13,10 +11,6 @@
 /delete-node/ &smem_region;
 
 / {
-	model = "Samsung Galaxy Tab 4 10.1";
-	compatible = "samsung,matisse-wifi", "qcom,apq8026";
-	chassis-type = "tablet";
-
 	aliases {
 		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
 		mmc1 = &sdhc_2; /* SDC2 SD card slot */
@@ -141,19 +135,6 @@ reg_tsp_1p8v: regulator-tsp-1p8v {
 		pinctrl-0 = <&tsp_en_default_state>;
 	};
 
-	reg_tsp_3p3v: regulator-tsp-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "tsp_3p3v";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_en1_default_state>;
-	};
-
 	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -223,26 +204,6 @@ &adsp {
 	status = "okay";
 };
 
-&blsp1_i2c2 {
-	status = "okay";
-
-	accelerometer@1d {
-		compatible = "st,lis2hh12";
-		reg = <0x1d>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&accel_int_default_state>;
-
-		st,drdy-int-pin = <1>;
-
-		vdd-supply = <&pm8226_l19>;
-		vddio-supply = <&pm8226_lvs1>;
-	};
-};
-
 &blsp1_i2c4 {
 	status = "okay";
 
@@ -258,26 +219,6 @@ muic: usb-switch@25 {
 	};
 };
 
-&blsp1_i2c5 {
-	status = "okay";
-
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_int_rst_default_state>;
-
-		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
-
-		vdd-supply = <&reg_tsp_1p8v>;
-		vdda-supply = <&reg_tsp_3p3v>;
-	};
-};
-
 &rpm_requests {
 	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
@@ -492,13 +433,6 @@ tsp_en_default_state: tsp-en-default-state {
 		bias-disable;
 	};
 
-	tsp_en1_default_state: tsp-en1-default-state {
-		pins = "gpio73";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
 	tsp_int_rst_default_state: tsp-int-rst-default-state {
 		pins = "gpio17";
 		function = "gpio";
-- 
2.41.0

[PATCH v5 2/4] dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE

[Stefan Hansson]

This documents Samsung Galaxy Tab 4 10.1 LTE (samsung,matisselte)
which is a tablet by Samsung based on the MSM8926 SoC.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 88b84035e7b1..242ffe89c6c6 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -196,6 +196,7 @@ properties:
           - enum:
               - microsoft,superman-lte
               - microsoft,tesla
+              - samsung,matisselte
           - const: qcom,msm8926
           - const: qcom,msm8226
 
-- 
2.41.0

[PATCH v5 3/4] ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 LTE (SM-T535)

[Stefan Hansson]

Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T535) LTE tablet
based on the MSM8926 platform.

The common dtsi is also modified to describe the widest constraints,
which required modifications to the matisse-wifi dts.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm/boot/dts/qcom/Makefile               |  1 +
 .../qcom-apq8026-samsung-matisse-wifi.dts     |  8 ++++
 .../qcom-msm8226-samsung-matisse-common.dtsi  |  4 +-
 .../qcom/qcom-msm8926-samsung-matisselte.dts  | 37 +++++++++++++++++++
 4 files changed, 48 insertions(+), 2 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts

diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
index a3d293e40820..cab35eeb30f6 100644
--- a/arch/arm/boot/dts/qcom/Makefile
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8916-samsung-serranove.dtb \
 	qcom-msm8926-microsoft-superman-lte.dtb \
 	qcom-msm8926-microsoft-tesla.dtb \
+	qcom-msm8926-samsung-matisselte.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8960-samsung-expressatt.dtb \
 	qcom-msm8974-lge-nexus5-hammerhead.dtb \
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
index b0da51f67539..3be02bdbb919 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -66,6 +66,14 @@ touchscreen@4a {
 	};
 };
 
+&pm8226_l3 {
+	regulator-max-microvolt = <1337500>;
+};
+
+&pm8226_s4 {
+	regulator-max-microvolt = <1800000>;
+};
+
 &tlmm {
 	tsp_en1_default_state: tsp-en1-default-state {
 		pins = "gpio73";
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
index ef98d88927ca..28317ce79e97 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -230,7 +230,7 @@ pm8226_s3: s3 {
 
 		pm8226_s4: s4 {
 			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
 		};
 
 		pm8226_s5: s5 {
@@ -250,7 +250,7 @@ pm8226_l2: l2 {
 
 		pm8226_l3: l3 {
 			regulator-min-microvolt = <750000>;
-			regulator-max-microvolt = <1337500>;
+			regulator-max-microvolt = <1350000>;
 			regulator-always-on;
 		};
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
new file mode 100644
index 000000000000..d0e1bc39f8ef
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ * Copyright (c) 2023, Stefan Hansson <newbyte@postmarketos.org>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1 LTE";
+	compatible = "samsung,matisselte", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "tablet";
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+};
+
+&tlmm {
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
-- 
2.41.0

[PATCH v5 4/4] ARM: dts: qcom: samsung-matisse-common: Add UART

[Stefan Hansson]

This was not enabled in the matisse-wifi tree. Without this, it is not
possible to use the USB port for serial debugging via a "Carkit debug
cable".

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi    | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
index 28317ce79e97..dc63b91f94bc 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -219,6 +219,10 @@ muic: usb-switch@25 {
 	};
 };
 
+&blsp1_uart3 {
+	status = "okay";
+};
+
 &rpm_requests {
 	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
-- 
2.41.0

Re: [PATCH v5 0/4] Add samsung-matisselte and common matisse dtsi

[Bjorn Andersson]

On Tue, 31 Oct 2023 15:00:54 +0100, Stefan Hansson wrote:
> This series adds a common samsung-matisse dtsi and reworks
> samsung-matisse-wifi to use it, and introduces samsung-matisselte. I
> choose matisselte over matisse-lte as this is how most other devices
> (klte, s3ve3g) do it and it is the codename that Samsung gave the
> device. See individual commits for more information.
> 

Applied, thanks!

[1/4] ARM: dts: qcom: samsung-matisse-common: Add initial common device tree
      (no commit info)
[2/4] dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE
      commit: 2a478a521876d9daea016be3e9513a67871169b5
[3/4] ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 LTE (SM-T535)
      (no commit info)
[4/4] ARM: dts: qcom: samsung-matisse-common: Add UART
      (no commit info)

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>