From: greearb@candelatech.com
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org, Ben Greear <greearb@candelatech.com>
Subject: [PATCH v2 16/21] ath10k: Support 32+ stations.
Date: Wed, 11 May 2016 10:02:28 -0700 [thread overview]
Message-ID: <1462986153-16318-17-git-send-email-greearb@candelatech.com> (raw)
In-Reply-To: <1462986153-16318-1-git-send-email-greearb@candelatech.com>
From: Ben Greear <greearb@candelatech.com>
Support up to 32 stations when using CT firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
---
drivers/net/wireless/ath/ath10k/core.c | 14 +++++++++++
drivers/net/wireless/ath/ath10k/hw.h | 6 +++++
drivers/net/wireless/ath/ath10k/mac.c | 43 ++++++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 16 ++++++++++---
4 files changed, 76 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 49c85c3..3869edd 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -1567,6 +1567,20 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
break;
case ATH10K_FW_WMI_OP_VERSION_10_1:
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ fw_file->fw_features)) {
+ ar->max_num_peers = TARGET_10X_NUM_PEERS_CT;
+ ar->max_num_stations = TARGET_10X_NUM_STATIONS;
+ ar->max_num_vdevs = TARGET_10X_NUM_VDEVS_CT;
+ } else {
+ ar->max_num_peers = TARGET_10X_NUM_PEERS;
+ ar->max_num_stations = TARGET_10X_NUM_STATIONS;
+ ar->max_num_vdevs = TARGET_10X_NUM_VDEVS;
+ }
+ ar->htt.max_num_pending_tx = TARGET_10X_NUM_MSDU_DESC;
+ ar->fw_stats_req_mask = WMI_STAT_PEER;
+ ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
+ break;
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
if (ath10k_peer_stats_enabled(ar)) {
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 7b80e29..d3f37d5 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -370,6 +370,12 @@ enum ath10k_hw_4addr_pad {
(TARGET_10X_NUM_VDEVS))
#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \
(TARGET_10X_NUM_VDEVS))
+
+/* Over-rides for Candela Technologies firmware */
+#define TARGET_10X_NUM_VDEVS_CT 32
+#define TARGET_10X_NUM_PEERS_CT (32 + (TARGET_10X_NUM_VDEVS_CT))
+#define TARGET_10X_AST_SKID_LIMIT_CT (TARGET_10X_NUM_PEERS_CT * TARGET_10X_NUM_PEER_AST)
+
#define TARGET_10X_NUM_OFFLOAD_PEERS 0
#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0
#define TARGET_10X_NUM_PEER_KEYS 2
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 42cac32..2169337 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -7451,6 +7451,22 @@ static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = {
},
};
+static const struct ieee80211_iface_limit ath10k_10x_ct_if_limits[] = {
+ {
+ .max = TARGET_10X_NUM_VDEVS_CT,
+ .types = BIT(NL80211_IFTYPE_STATION)
+ | BIT(NL80211_IFTYPE_P2P_CLIENT)
+ },
+ {
+ .max = 3,
+ .types = BIT(NL80211_IFTYPE_P2P_GO)
+ },
+ {
+ .max = 7,
+ .types = BIT(NL80211_IFTYPE_AP)
+ },
+};
+
static const struct ieee80211_iface_combination ath10k_if_comb[] = {
{
.limits = ath10k_if_limits,
@@ -7531,6 +7547,22 @@ static const struct ieee80211_iface_limit ath10k_tlv_if_limit_ibss[] = {
},
};
+static const struct ieee80211_iface_combination ath10k_10x_ct_if_comb[] = {
+ {
+ .limits = ath10k_10x_ct_if_limits,
+ .n_limits = ARRAY_SIZE(ath10k_10x_ct_if_limits),
+ .max_interfaces = TARGET_10X_NUM_VDEVS_CT,
+ .num_different_channels = 1,
+ .beacon_int_infra_match = true,
+#ifdef CONFIG_ATH10K_DFS_CERTIFIED
+ .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
+ BIT(NL80211_CHAN_WIDTH_20) |
+ BIT(NL80211_CHAN_WIDTH_40) |
+ BIT(NL80211_CHAN_WIDTH_80),
+#endif
+ },
+};
+
/* FIXME: This is not thouroughly tested. These combinations may over- or
* underestimate hw/fw capabilities.
*/
@@ -7808,6 +7840,17 @@ int ath10k_mac_register(struct ath10k *ar)
ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC);
break;
case ATH10K_FW_WMI_OP_VERSION_10_1:
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ ar->normal_mode_fw.fw_file.fw_features)) {
+ ar->hw->wiphy->iface_combinations = ath10k_10x_ct_if_comb;
+ ar->hw->wiphy->n_iface_combinations =
+ ARRAY_SIZE(ath10k_10x_ct_if_comb);
+ } else {
+ ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb;
+ ar->hw->wiphy->n_iface_combinations =
+ ARRAY_SIZE(ath10k_10x_if_comb);
+ }
+ break;
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb;
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 6cfba41..9ee2648 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -5497,12 +5497,22 @@ static struct sk_buff *ath10k_wmi_10_1_op_gen_init(struct ath10k *ar)
struct sk_buff *buf;
struct wmi_resource_config_10x config = {};
u32 len, val;
+ u32 skid_limit;
+
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ ar->running_fw->fw_file.fw_features)) {
+ config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS_CT);
+ config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS_CT);
+ skid_limit = TARGET_10X_AST_SKID_LIMIT_CT;
+ } else {
+ config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS);
+ config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS);
+ skid_limit = TARGET_10X_AST_SKID_LIMIT;
+ }
+ config.ast_skid_limit = __cpu_to_le32(skid_limit);
- config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS);
- config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS);
config.num_peer_keys = __cpu_to_le32(TARGET_10X_NUM_PEER_KEYS);
config.num_tids = __cpu_to_le32(TARGET_10X_NUM_TIDS);
- config.ast_skid_limit = __cpu_to_le32(TARGET_10X_AST_SKID_LIMIT);
config.tx_chain_mask = __cpu_to_le32(TARGET_10X_TX_CHAIN_MASK);
config.rx_chain_mask = __cpu_to_le32(TARGET_10X_RX_CHAIN_MASK);
config.rx_timeout_pri_vo = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
--
2.4.3
WARNING: multiple messages have this Message-ID (diff)
From: greearb@candelatech.com
To: ath10k@lists.infradead.org
Cc: Ben Greear <greearb@candelatech.com>, linux-wireless@vger.kernel.org
Subject: [PATCH v2 16/21] ath10k: Support 32+ stations.
Date: Wed, 11 May 2016 10:02:28 -0700 [thread overview]
Message-ID: <1462986153-16318-17-git-send-email-greearb@candelatech.com> (raw)
In-Reply-To: <1462986153-16318-1-git-send-email-greearb@candelatech.com>
From: Ben Greear <greearb@candelatech.com>
Support up to 32 stations when using CT firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
---
drivers/net/wireless/ath/ath10k/core.c | 14 +++++++++++
drivers/net/wireless/ath/ath10k/hw.h | 6 +++++
drivers/net/wireless/ath/ath10k/mac.c | 43 ++++++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath10k/wmi.c | 16 ++++++++++---
4 files changed, 76 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index 49c85c3..3869edd 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -1567,6 +1567,20 @@ static int ath10k_core_init_firmware_features(struct ath10k *ar)
ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
break;
case ATH10K_FW_WMI_OP_VERSION_10_1:
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ fw_file->fw_features)) {
+ ar->max_num_peers = TARGET_10X_NUM_PEERS_CT;
+ ar->max_num_stations = TARGET_10X_NUM_STATIONS;
+ ar->max_num_vdevs = TARGET_10X_NUM_VDEVS_CT;
+ } else {
+ ar->max_num_peers = TARGET_10X_NUM_PEERS;
+ ar->max_num_stations = TARGET_10X_NUM_STATIONS;
+ ar->max_num_vdevs = TARGET_10X_NUM_VDEVS;
+ }
+ ar->htt.max_num_pending_tx = TARGET_10X_NUM_MSDU_DESC;
+ ar->fw_stats_req_mask = WMI_STAT_PEER;
+ ar->max_spatial_stream = WMI_MAX_SPATIAL_STREAM;
+ break;
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
if (ath10k_peer_stats_enabled(ar)) {
diff --git a/drivers/net/wireless/ath/ath10k/hw.h b/drivers/net/wireless/ath/ath10k/hw.h
index 7b80e29..d3f37d5 100644
--- a/drivers/net/wireless/ath/ath10k/hw.h
+++ b/drivers/net/wireless/ath/ath10k/hw.h
@@ -370,6 +370,12 @@ enum ath10k_hw_4addr_pad {
(TARGET_10X_NUM_VDEVS))
#define TARGET_10X_TX_STATS_NUM_PEERS ((TARGET_10X_TX_STATS_NUM_STATIONS) + \
(TARGET_10X_NUM_VDEVS))
+
+/* Over-rides for Candela Technologies firmware */
+#define TARGET_10X_NUM_VDEVS_CT 32
+#define TARGET_10X_NUM_PEERS_CT (32 + (TARGET_10X_NUM_VDEVS_CT))
+#define TARGET_10X_AST_SKID_LIMIT_CT (TARGET_10X_NUM_PEERS_CT * TARGET_10X_NUM_PEER_AST)
+
#define TARGET_10X_NUM_OFFLOAD_PEERS 0
#define TARGET_10X_NUM_OFFLOAD_REORDER_BUFS 0
#define TARGET_10X_NUM_PEER_KEYS 2
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 42cac32..2169337 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -7451,6 +7451,22 @@ static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = {
},
};
+static const struct ieee80211_iface_limit ath10k_10x_ct_if_limits[] = {
+ {
+ .max = TARGET_10X_NUM_VDEVS_CT,
+ .types = BIT(NL80211_IFTYPE_STATION)
+ | BIT(NL80211_IFTYPE_P2P_CLIENT)
+ },
+ {
+ .max = 3,
+ .types = BIT(NL80211_IFTYPE_P2P_GO)
+ },
+ {
+ .max = 7,
+ .types = BIT(NL80211_IFTYPE_AP)
+ },
+};
+
static const struct ieee80211_iface_combination ath10k_if_comb[] = {
{
.limits = ath10k_if_limits,
@@ -7531,6 +7547,22 @@ static const struct ieee80211_iface_limit ath10k_tlv_if_limit_ibss[] = {
},
};
+static const struct ieee80211_iface_combination ath10k_10x_ct_if_comb[] = {
+ {
+ .limits = ath10k_10x_ct_if_limits,
+ .n_limits = ARRAY_SIZE(ath10k_10x_ct_if_limits),
+ .max_interfaces = TARGET_10X_NUM_VDEVS_CT,
+ .num_different_channels = 1,
+ .beacon_int_infra_match = true,
+#ifdef CONFIG_ATH10K_DFS_CERTIFIED
+ .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
+ BIT(NL80211_CHAN_WIDTH_20) |
+ BIT(NL80211_CHAN_WIDTH_40) |
+ BIT(NL80211_CHAN_WIDTH_80),
+#endif
+ },
+};
+
/* FIXME: This is not thouroughly tested. These combinations may over- or
* underestimate hw/fw capabilities.
*/
@@ -7808,6 +7840,17 @@ int ath10k_mac_register(struct ath10k *ar)
ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC);
break;
case ATH10K_FW_WMI_OP_VERSION_10_1:
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ ar->normal_mode_fw.fw_file.fw_features)) {
+ ar->hw->wiphy->iface_combinations = ath10k_10x_ct_if_comb;
+ ar->hw->wiphy->n_iface_combinations =
+ ARRAY_SIZE(ath10k_10x_ct_if_comb);
+ } else {
+ ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb;
+ ar->hw->wiphy->n_iface_combinations =
+ ARRAY_SIZE(ath10k_10x_if_comb);
+ }
+ break;
case ATH10K_FW_WMI_OP_VERSION_10_2:
case ATH10K_FW_WMI_OP_VERSION_10_2_4:
ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb;
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 6cfba41..9ee2648 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -5497,12 +5497,22 @@ static struct sk_buff *ath10k_wmi_10_1_op_gen_init(struct ath10k *ar)
struct sk_buff *buf;
struct wmi_resource_config_10x config = {};
u32 len, val;
+ u32 skid_limit;
+
+ if (test_bit(ATH10K_FW_FEATURE_WMI_10X_CT,
+ ar->running_fw->fw_file.fw_features)) {
+ config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS_CT);
+ config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS_CT);
+ skid_limit = TARGET_10X_AST_SKID_LIMIT_CT;
+ } else {
+ config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS);
+ config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS);
+ skid_limit = TARGET_10X_AST_SKID_LIMIT;
+ }
+ config.ast_skid_limit = __cpu_to_le32(skid_limit);
- config.num_vdevs = __cpu_to_le32(TARGET_10X_NUM_VDEVS);
- config.num_peers = __cpu_to_le32(TARGET_10X_NUM_PEERS);
config.num_peer_keys = __cpu_to_le32(TARGET_10X_NUM_PEER_KEYS);
config.num_tids = __cpu_to_le32(TARGET_10X_NUM_TIDS);
- config.ast_skid_limit = __cpu_to_le32(TARGET_10X_AST_SKID_LIMIT);
config.tx_chain_mask = __cpu_to_le32(TARGET_10X_TX_CHAIN_MASK);
config.rx_chain_mask = __cpu_to_le32(TARGET_10X_RX_CHAIN_MASK);
config.rx_timeout_pri_vo = __cpu_to_le32(TARGET_10X_RX_TIMEOUT_LO_PRI);
--
2.4.3
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next prev parent reply other threads:[~2016-05-11 17:02 UTC|newest]
Thread overview: 118+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-11 17:02 [PATCH v2 00/21] ath10k patches, generic and CT firmware related greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 01/21] ath10k: Fix crash related to printing features greearb
2016-05-11 17:02 ` greearb
2016-06-07 11:38 ` [v2,01/21] " Kalle Valo
2016-06-07 11:38 ` Kalle Valo
2016-06-20 20:49 ` [PATCH v2 01/21] " Ben Greear
2016-06-20 20:49 ` Ben Greear
2016-06-20 21:56 ` Valo, Kalle
2016-06-20 21:56 ` Valo, Kalle
2016-05-11 17:02 ` [PATCH v2 02/21] ath10k: fix typo in logging message greearb
2016-05-11 17:02 ` greearb
2016-09-27 12:19 ` [v2,02/21] " Kalle Valo
2016-09-27 12:19 ` Kalle Valo
2016-05-11 17:02 ` [PATCH v2 03/21] ath10k: Allow changing ath10k debug mask at runtime greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:06 ` Valo, Kalle
2016-09-14 14:06 ` Valo, Kalle
2016-09-14 15:33 ` Ben Greear
2016-09-14 15:33 ` Ben Greear
2016-09-15 14:19 ` Valo, Kalle
2016-09-15 14:19 ` Valo, Kalle
2016-09-15 15:07 ` Ben Greear
2016-09-15 15:07 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 04/21] ath10k: rate-limit packet tx errors greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:07 ` Valo, Kalle
2016-09-14 14:07 ` Valo, Kalle
2016-09-14 15:02 ` Ben Greear
2016-09-14 15:02 ` Ben Greear
2016-09-15 13:59 ` Valo, Kalle
2016-09-15 13:59 ` Valo, Kalle
2016-09-15 15:22 ` Ben Greear
2016-09-15 15:22 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 05/21] ath10k: save firmware debug log messages greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 06/21] ath10k: save firmware stacks upon firmware crash greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 07/21] ath10k: save firmware RAM and ROM BSS sections on crash greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 08/21] ath10k: make firmware text debug messages more verbose greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:12 ` Valo, Kalle
2016-09-14 14:12 ` Valo, Kalle
2016-09-14 15:06 ` Ben Greear
2016-09-14 15:06 ` Ben Greear
2016-09-15 14:02 ` Valo, Kalle
2016-09-15 14:02 ` Valo, Kalle
2016-09-15 15:17 ` Ben Greear
2016-09-15 15:17 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 09/21] ath10k: print fw debug messages in hex greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:18 ` Valo, Kalle
2016-09-14 14:18 ` Valo, Kalle
2016-09-14 15:13 ` Ben Greear
2016-09-14 15:13 ` Ben Greear
2016-09-15 14:06 ` Valo, Kalle
2016-09-15 14:06 ` Valo, Kalle
2016-09-15 15:14 ` Ben Greear
2016-09-15 15:14 ` Ben Greear
2016-09-15 17:34 ` Grumbach, Emmanuel
2016-09-15 17:34 ` Grumbach, Emmanuel
2016-09-15 17:59 ` Ben Greear
2016-09-15 17:59 ` Ben Greear
2016-09-15 18:08 ` Ben Greear
2016-09-15 18:08 ` Ben Greear
2016-09-15 20:22 ` Grumbach, Emmanuel
2016-09-15 20:22 ` Grumbach, Emmanuel
2016-05-11 17:02 ` [PATCH v2 10/21] ath10k: support logging ath10k_info as KERN_DEBUG greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:19 ` Valo, Kalle
2016-09-14 14:19 ` Valo, Kalle
2016-09-14 15:14 ` Ben Greear
2016-09-14 15:14 ` Ben Greear
2016-09-15 14:12 ` Valo, Kalle
2016-09-15 14:12 ` Valo, Kalle
2016-09-15 15:11 ` Ben Greear
2016-09-15 15:11 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 11/21] ath10k: add fw-powerup-fail to ethtool stats greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:25 ` Valo, Kalle
2016-09-14 14:25 ` Valo, Kalle
2016-09-14 15:19 ` Ben Greear
2016-09-14 15:19 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 12/21] ath10k: Support up to 64 vdevs greearb
2016-05-11 17:02 ` greearb
2016-09-14 15:01 ` Valo, Kalle
2016-09-14 15:01 ` Valo, Kalle
2016-05-11 17:02 ` [PATCH v2 13/21] ath10k: Document cycle count related counters greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 14/21] ath10k: Add tx/rx bytes, cycle counters to ethtool stats greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 15/21] ath10k: support CT firmware flag greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:30 ` Valo, Kalle
2016-09-14 14:30 ` Valo, Kalle
2016-09-14 15:24 ` Ben Greear
2016-09-14 15:24 ` Ben Greear
2016-09-15 14:15 ` Valo, Kalle
2016-09-15 14:15 ` Valo, Kalle
2016-09-15 14:43 ` Ben Greear
2016-09-15 14:43 ` Ben Greear
2016-05-11 17:02 ` greearb [this message]
2016-05-11 17:02 ` [PATCH v2 16/21] ath10k: Support 32+ stations greearb
2016-05-11 17:02 ` [PATCH v2 17/21] ath10k: Enable detecting failure to install key in firmware (CT) greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 18/21] ath10k: Note limitation on beaconing vdevs greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 19/21] ath10k: Enable adhoc mode for CT firmware greearb
2016-05-11 17:02 ` greearb
2016-09-14 14:37 ` Valo, Kalle
2016-09-14 14:37 ` Valo, Kalle
2016-09-14 15:28 ` Ben Greear
2016-09-14 15:28 ` Ben Greear
2016-05-11 17:02 ` [PATCH v2 20/21] ath10k: read firmware crash over ioread32 if CE fails greearb
2016-05-11 17:02 ` greearb
2016-05-11 17:02 ` [PATCH v2 21/21] ath10k: Read dbglog buffers over register ping-pong greearb
2016-05-11 17:02 ` greearb
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1462986153-16318-17-git-send-email-greearb@candelatech.com \
--to=greearb@candelatech.com \
--cc=ath10k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.