From: Sricharan R <sricharan@codeaurora.org>
To: robh+dt@kernel.org, robh@kernel.org, mark.rutland@arm.com,
linux@armlinux.org.uk, andy.gross@linaro.org,
david.brown@linaro.org, catalin.marinas@arm.com,
will.deacon@arm.com, sboyd@codeaurora.org,
bjorn.andersson@linaro.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
absahu@codeaurora.org, marc.zyngier@arm.com,
richardcochran@gmail.com, sricharan@codeaurora.org
Subject: [PATCH v8 10/12] ARM: dts: ipq8074: Add peripheral nodes
Date: Fri, 25 May 2018 11:41:20 +0530 [thread overview]
Message-ID: <1527228682-12285-11-git-send-email-sricharan@codeaurora.org> (raw)
In-Reply-To: <1527228682-12285-1-git-send-email-sricharan@codeaurora.org>
Add serial, i2c, bam, spi, qpic peripheral nodes.
While here, fix the PMU node's irq trigger to avoid
the boot warnings from GIC.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 12 ---
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 156 +++++++++++++++++++++++++++++-
2 files changed, 155 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index 6a838b5..72c5b4a3 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -33,19 +33,7 @@
};
soc {
- pinctrl@1000000 {
- serial_4_pins: serial4_pinmux {
- mux {
- pins = "gpio23", "gpio24";
- function = "blsp4_uart1";
- bias-disable;
- };
- };
- };
-
serial@78b3000 {
- pinctrl-0 = <&serial_4_pins>;
- pinctrl-names = "default";
status = "ok";
};
};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2bc5dec..bd58ab4 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -32,6 +32,45 @@
#gpio-cells = <0x2>;
interrupt-controller;
#interrupt-cells = <0x2>;
+
+ serial_4_pins: serial4-pinmux {
+ pins = "gpio23", "gpio24";
+ function = "blsp4_uart1";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ i2c_0_pins: i2c-0-pinmux {
+ pins = "gpio42", "gpio43";
+ function = "blsp1_i2c";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ spi_0_pins: spi-0-pins {
+ pins = "gpio38", "gpio39", "gpio40", "gpio41";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ hsuart_pins: hsuart-pins {
+ pins = "gpio46", "gpio47", "gpio48", "gpio49";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ qpic_pins: qpic-pins {
+ pins = "gpio1", "gpio3", "gpio4",
+ "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio10", "gpio11",
+ "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17";
+ function = "qpic";
+ drive-strength = <8>;
+ bias-disable;
+ };
};
intc: interrupt-controller@b000000 {
@@ -122,6 +161,121 @@
clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
+ pinctrl-0 = <&serial_4_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp_dma: dma@7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x7884000 0x2b000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ blsp1_uart1: serial@78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x78af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_uart3: serial@78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x78b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>,
+ <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-0 = <&hsuart_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_spi1: spi@78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ spi-max-frequency = <50000000>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c@78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ clock-frequency = <400000>;
+ dmas = <&blsp_dma 15>, <&blsp_dma 14>;
+ dma-names = "rx", "tx";
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_i2c3: i2c@78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ clock-frequency = <100000>;
+ dmas = <&blsp_dma 17>, <&blsp_dma 16>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ qpic_bam: dma@7984000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x7984000 0x1a000>;
+ interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ qpic_nand: nand@79b0000 {
+ compatible = "qcom,ipq8074-nand";
+ reg = <0x79b0000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&gcc GCC_QPIC_CLK>,
+ <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&qpic_bam 0>,
+ <&qpic_bam 1>,
+ <&qpic_bam 2>;
+ dma-names = "tx", "rx", "cmd";
+ pinctrl-0 = <&qpic_pins>;
+ pinctrl-names = "default";
status = "disabled";
};
};
@@ -175,7 +329,7 @@
pmu {
compatible = "arm,armv8-pmuv3";
- interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
clocks {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
WARNING: multiple messages have this Message-ID (diff)
From: sricharan@codeaurora.org (Sricharan R)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v8 10/12] ARM: dts: ipq8074: Add peripheral nodes
Date: Fri, 25 May 2018 11:41:20 +0530 [thread overview]
Message-ID: <1527228682-12285-11-git-send-email-sricharan@codeaurora.org> (raw)
In-Reply-To: <1527228682-12285-1-git-send-email-sricharan@codeaurora.org>
Add serial, i2c, bam, spi, qpic peripheral nodes.
While here, fix the PMU node's irq trigger to avoid
the boot warnings from GIC.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
---
arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 12 ---
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 156 +++++++++++++++++++++++++++++-
2 files changed, 155 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index 6a838b5..72c5b4a3 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -33,19 +33,7 @@
};
soc {
- pinctrl at 1000000 {
- serial_4_pins: serial4_pinmux {
- mux {
- pins = "gpio23", "gpio24";
- function = "blsp4_uart1";
- bias-disable;
- };
- };
- };
-
serial at 78b3000 {
- pinctrl-0 = <&serial_4_pins>;
- pinctrl-names = "default";
status = "ok";
};
};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 2bc5dec..bd58ab4 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -32,6 +32,45 @@
#gpio-cells = <0x2>;
interrupt-controller;
#interrupt-cells = <0x2>;
+
+ serial_4_pins: serial4-pinmux {
+ pins = "gpio23", "gpio24";
+ function = "blsp4_uart1";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ i2c_0_pins: i2c-0-pinmux {
+ pins = "gpio42", "gpio43";
+ function = "blsp1_i2c";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ spi_0_pins: spi-0-pins {
+ pins = "gpio38", "gpio39", "gpio40", "gpio41";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ hsuart_pins: hsuart-pins {
+ pins = "gpio46", "gpio47", "gpio48", "gpio49";
+ function = "blsp2_uart";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ qpic_pins: qpic-pins {
+ pins = "gpio1", "gpio3", "gpio4",
+ "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio10", "gpio11",
+ "gpio12", "gpio13", "gpio14",
+ "gpio15", "gpio16", "gpio17";
+ function = "qpic";
+ drive-strength = <8>;
+ bias-disable;
+ };
};
intc: interrupt-controller at b000000 {
@@ -122,6 +161,121 @@
clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
+ pinctrl-0 = <&serial_4_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp_dma: dma at 7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x7884000 0x2b000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+ blsp1_uart1: serial at 78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x78af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+
+ blsp1_uart3: serial at 78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x78b1000 0x200>;
+ interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>,
+ <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-0 = <&hsuart_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_spi1: spi at 78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ spi-max-frequency = <50000000>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c at 78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ clock-frequency = <400000>;
+ dmas = <&blsp_dma 15>, <&blsp_dma 14>;
+ dma-names = "rx", "tx";
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ };
+
+ blsp1_i2c3: i2c at 78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x78b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ clock-frequency = <100000>;
+ dmas = <&blsp_dma 17>, <&blsp_dma 16>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ qpic_bam: dma at 7984000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x7984000 0x1a000>;
+ interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ qpic_nand: nand at 79b0000 {
+ compatible = "qcom,ipq8074-nand";
+ reg = <0x79b0000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&gcc GCC_QPIC_CLK>,
+ <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&qpic_bam 0>,
+ <&qpic_bam 1>,
+ <&qpic_bam 2>;
+ dma-names = "tx", "rx", "cmd";
+ pinctrl-0 = <&qpic_pins>;
+ pinctrl-names = "default";
status = "disabled";
};
};
@@ -175,7 +329,7 @@
pmu {
compatible = "arm,armv8-pmuv3";
- interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
clocks {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2018-05-25 6:11 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-25 6:11 [PATCH v8 00/12] ARM: dts: ipq: updates to enable a few peripherals Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 01/12] ARM: dts: ipq4019: Add a default chosen node Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 02/12] ARM: dts: ipq4019: Add a few peripheral nodes Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 03/12] ARM: dts: ipq4019: Change the max opp frequency Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 04/12] ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 05/12] ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 06/12] ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 " Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 07/12] ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 08/12] ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 09/12] ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 " Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` Sricharan R [this message]
2018-05-25 6:11 ` [PATCH v8 10/12] ARM: dts: ipq8074: Add peripheral nodes Sricharan R
2018-05-25 6:11 ` [PATCH v8 11/12] ARM: dts: ipq8074: Add pcie nodes Sricharan R
2018-05-25 6:11 ` Sricharan R
2018-05-25 6:11 ` [PATCH v8 12/12] ARM: dts: ipq8074: Enable few peripherals for hk01 board Sricharan R
2018-05-25 6:11 ` Sricharan R
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1527228682-12285-11-git-send-email-sricharan@codeaurora.org \
--to=sricharan@codeaurora.org \
--cc=absahu@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=catalin.marinas@arm.com \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=marc.zyngier@arm.com \
--cc=mark.rutland@arm.com \
--cc=richardcochran@gmail.com \
--cc=robh+dt@kernel.org \
--cc=robh@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.