[PATCH v5 3/3] regulator: mcp16502: add regulator driver for MCP16502

From: <Andrei.Stefanescu@microchip.com>
To: <broonie@kernel.org>, <robh+dt@kernel.org>, <lgirdwood@gmail.com>,
	<mark.rutland@arm.com>, <gregkh@linuxfoundation.org>
Cc: <Cristian.Birsan@microchip.com>, <Nicolas.Ferre@microchip.com>,
	<Claudiu.Beznea@microchip.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<andr3i.stefanescu@gmail.com>, <Andrei.Stefanescu@microchip.com>
Subject: [PATCH v5 3/3] regulator: mcp16502: add regulator driver for MCP16502
Date: Wed, 12 Dec 2018 18:31:18 +0000	[thread overview]
Message-ID: <1544639447-17392-4-git-send-email-andrei.stefanescu@microchip.com> (raw)
In-Reply-To: <1544639447-17392-1-git-send-email-andrei.stefanescu@microchip.com>

This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status

Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
---
 drivers/regulator/Kconfig    |   9 +
 drivers/regulator/Makefile   |   1 +
 drivers/regulator/mcp16502.c | 520 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 530 insertions(+)
 create mode 100644 drivers/regulator/mcp16502.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 926cee0..719d9d6 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -567,6 +567,15 @@ config REGULATOR_MC13892
 	  Say y here to support the regulators found on the Freescale MC13892
 	  PMIC.
 
+config REGULATOR_MCP16502
+	tristate "Microchip MCP16502 PMIC"
+	depends on I2C && OF
+	help
+	  Say y here to support the MCP16502 PMIC. This driver supports
+	  basic operations (get/set voltage, get/set operating mode)
+	  through the regulator interface. In addition it enables
+	  suspend-to-ram/standby transition.
+
 config REGULATOR_MT6311
 	tristate "MediaTek MT6311 PMIC"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 72488ef..b12e1c9 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -74,6 +74,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802-regulator.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
 obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
 obj-$(CONFIG_REGULATOR_MC13XXX_CORE) +=  mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
 obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
 obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
 obj-$(CONFIG_REGULATOR_MT6380)	+= mt6380-regulator.o
diff --git a/drivers/regulator/mcp16502.c b/drivers/regulator/mcp16502.c
new file mode 100644
index 0000000..7cbc96f
--- /dev/null
+++ b/drivers/regulator/mcp16502.c
@@ -0,0 +1,520 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// MCP16502 PMIC driver
+//
+// Copyright (C) 2018 Microchip Technology Inc. and its subsidiaries
+//
+// Author: Andrei Stefanescu <andrei.stefanescu@microchip.com>
+//
+// Inspired from tps65086-regulator.c
+
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/suspend.h>
+
+#define VDD_LOW_SEL 0x0D
+#define VDD_HIGH_SEL 0x3F
+
+#define MCP16502_FLT BIT(7)
+#define MCP16502_ENS BIT(0)
+
+/*
+ * The PMIC has four sets of registers corresponding to four power modes:
+ * Performance, Active, Low-power, Hibernate.
+ *
+ * Registers:
+ * Each regulator has a register for each power mode. To access a register
+ * for a specific regulator and mode BASE_* and OFFSET_* need to be added.
+ *
+ * Operating modes:
+ * In order for the PMIC to transition to operating modes it has to be
+ * controlled via GPIO lines called LPM and HPM.
+ *
+ * The registers are fully configurable such that you can put all regulators in
+ * a low-power state while the PMIC is in Active mode. They are supposed to be
+ * configured at startup and then simply transition to/from a global low-power
+ * state by setting the GPIO lpm pin high/low.
+ *
+ * This driver keeps the PMIC in Active mode, Low-power state is set for the
+ * regulators by enabling/disabling operating mode (FPWM or Auto PFM).
+ *
+ * The PMIC's Low-power and Hibernate modes are used during standby/suspend.
+ * To enter standby/suspend the PMIC will go to Low-power mode. From there, it
+ * will transition to Hibernate when the PWRHLD line is set to low by the MPU.
+ */
+
+/*
+ * This function is useful for iterating over all regulators and accessing their
+ * registers in a generic way or accessing a regulator device by its id.
+ */
+#define MCP16502_BASE(i) (((i) + 1) << 4)
+#define MCP16502_STAT_BASE(i) ((i) + 5)
+
+#define MCP16502_OFFSET_MODE_A 0
+#define MCP16502_OFFSET_MODE_LPM 1
+#define MCP16502_OFFSET_MODE_HIB 2
+
+#define MCP16502_OPMODE_ACTIVE REGULATOR_MODE_NORMAL
+#define MCP16502_OPMODE_LPM REGULATOR_MODE_IDLE
+#define MCP16502_OPMODE_HIB REGULATOR_MODE_STANDBY
+
+#define MCP16502_MODE_AUTO_PFM 0
+#define MCP16502_MODE_FPWM BIT(6)
+
+#define MCP16502_VSEL 0x3F
+#define MCP16502_EN BIT(7)
+#define MCP16502_MODE BIT(6)
+
+#define MCP16502_MIN_REG 0x0
+#define MCP16502_MAX_REG 0x65
+
+static unsigned int mcp16502_of_map_mode(unsigned int mode)
+{
+	if (mode == REGULATOR_MODE_NORMAL || mode == REGULATOR_MODE_IDLE)
+		return mode;
+
+	return REGULATOR_MODE_INVALID;
+}
+
+#define MCP16502_REGULATOR(_name, _id, _ranges, _ops)			\
+	[_id] = {							\
+		.name			= _name,			\
+		.regulators_node	= of_match_ptr("regulators"),	\
+		.id			= _id,				\
+		.ops			= &(_ops),			\
+		.type			= REGULATOR_VOLTAGE,		\
+		.owner			= THIS_MODULE,			\
+		.linear_ranges		= _ranges,			\
+		.n_linear_ranges	= ARRAY_SIZE(_ranges),		\
+		.of_match		= of_match_ptr(_name),		\
+		.of_map_mode		= mcp16502_of_map_mode,		\
+		.vsel_reg		= (((_id) + 1) << 4),		\
+		.vsel_mask		= MCP16502_VSEL,		\
+		.enable_reg		= (((_id) + 1) << 4),		\
+		.enable_mask		= MCP16502_EN,			\
+	}
+
+enum {
+	BUCK1 = 0,
+	BUCK2,
+	BUCK3,
+	BUCK4,
+	LDO1,
+	LDO2,
+	NUM_REGULATORS
+};
+
+/*
+ * struct mcp16502 - PMIC representation
+ * @rdev: the regulators belonging to this chip
+ * @rmap: regmap to be used for I2C communication
+ * @lpm: LPM GPIO descriptor
+ */
+struct mcp16502 {
+	struct regulator_dev *rdev[NUM_REGULATORS];
+	struct regmap *rmap;
+	struct gpio_desc *lpm;
+};
+
+/*
+ * mcp16502_gpio_set_mode() - set the GPIO corresponding value
+ *
+ * Used to prepare transitioning into hibernate or resuming from it.
+ */
+static void mcp16502_gpio_set_mode(struct mcp16502 *mcp, int mode)
+{
+	switch (mode) {
+	case MCP16502_OPMODE_ACTIVE:
+		gpiod_set_value(mcp->lpm, 0);
+		break;
+	case MCP16502_OPMODE_LPM:
+	case MCP16502_OPMODE_HIB:
+		gpiod_set_value(mcp->lpm, 1);
+		break;
+	default:
+		pr_err("%s: %d invalid\n", __func__, mode);
+	}
+}
+
+/*
+ * mcp16502_get_reg() - get the PMIC's configuration register for opmode
+ *
+ * @rdev: the regulator whose register we are searching
+ * @opmode: the PMIC's operating mode ACTIVE, Low-power, Hibernate
+ */
+static int mcp16502_get_reg(struct regulator_dev *rdev, int opmode)
+{
+	int reg = MCP16502_BASE(rdev_get_id(rdev));
+
+	switch (opmode) {
+	case MCP16502_OPMODE_ACTIVE:
+		return reg + MCP16502_OFFSET_MODE_A;
+	case MCP16502_OPMODE_LPM:
+		return reg + MCP16502_OFFSET_MODE_LPM;
+	case MCP16502_OPMODE_HIB:
+		return reg + MCP16502_OFFSET_MODE_HIB;
+	default:
+		return -EINVAL;
+	}
+}
+
+/*
+ * mcp16502_get_mode() - return the current operating mode of a regulator
+ *
+ * Note: all functions that are not part of entering/exiting standby/suspend
+ *	 use the Active mode registers.
+ *
+ * Note: this is different from the PMIC's operatig mode, it is the
+ *	 MODE bit from the regulator's register.
+ */
+static unsigned int mcp16502_get_mode(struct regulator_dev *rdev)
+{
+	unsigned int val;
+	int ret, reg;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	reg = mcp16502_get_reg(rdev, MCP16502_OPMODE_ACTIVE);
+	if (reg < 0)
+		return reg;
+
+	ret = regmap_read(mcp->rmap, reg, &val);
+	if (ret)
+		return ret;
+
+	switch (val & MCP16502_MODE) {
+	case MCP16502_MODE_FPWM:
+		return REGULATOR_MODE_NORMAL;
+	case MCP16502_MODE_AUTO_PFM:
+		return REGULATOR_MODE_IDLE;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+/*
+ * _mcp16502_set_mode() - helper for set_mode and set_suspend_mode
+ *
+ * @rdev: the regulator for which we are setting the mode
+ * @mode: the regulator's mode (the one from MODE bit)
+ * @opmode: the PMIC's operating mode: Active/Low-power/Hibernate
+ */
+static int _mcp16502_set_mode(struct regulator_dev *rdev, unsigned int mode,
+			      unsigned int op_mode)
+{
+	int val;
+	int reg;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	reg = mcp16502_get_reg(rdev, op_mode);
+	if (reg < 0)
+		return reg;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		val = MCP16502_MODE_FPWM;
+		break;
+	case REGULATOR_MODE_IDLE:
+		val = MCP16502_MODE_AUTO_PFM;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	reg = regmap_update_bits(mcp->rmap, reg, MCP16502_MODE, val);
+	return reg;
+}
+
+/*
+ * mcp16502_set_mode() - regulator_ops set_mode
+ */
+static int mcp16502_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_ACTIVE);
+}
+
+/*
+ * mcp16502_get_status() - regulator_ops get_status
+ */
+static int mcp16502_get_status(struct regulator_dev *rdev)
+{
+	int ret;
+	unsigned int val;
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+
+	ret = regmap_read(mcp->rmap, MCP16502_STAT_BASE(rdev_get_id(rdev)),
+			  &val);
+	if (ret)
+		return ret;
+
+	if (val & MCP16502_FLT)
+		return REGULATOR_STATUS_ERROR;
+	else if (val & MCP16502_ENS)
+		return REGULATOR_STATUS_ON;
+	else if (!(val & MCP16502_ENS))
+		return REGULATOR_STATUS_OFF;
+
+	return REGULATOR_STATUS_UNDEFINED;
+}
+
+#ifdef CONFIG_SUSPEND
+/*
+ * mcp16502_suspend_get_target_reg() - get the reg of the target suspend PMIC
+ *				       mode
+ */
+static int mcp16502_suspend_get_target_reg(struct regulator_dev *rdev)
+{
+	switch (pm_suspend_target_state) {
+	case PM_SUSPEND_STANDBY:
+		return mcp16502_get_reg(rdev, MCP16502_OPMODE_LPM);
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_MEM:
+		return mcp16502_get_reg(rdev, MCP16502_OPMODE_HIB);
+	default:
+		dev_err(&rdev->dev, "invalid suspend target: %d\n",
+			pm_suspend_target_state);
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * mcp16502_set_suspend_voltage() - regulator_ops set_suspend_voltage
+ */
+static int mcp16502_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int sel = regulator_map_voltage_linear_range(rdev, uV, uV);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (sel < 0)
+		return sel;
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_VSEL, sel);
+}
+
+/*
+ * mcp16502_set_suspend_mode() - regulator_ops set_suspend_mode
+ */
+static int mcp16502_set_suspend_mode(struct regulator_dev *rdev,
+				     unsigned int mode)
+{
+	switch (pm_suspend_target_state) {
+	case PM_SUSPEND_STANDBY:
+		return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_LPM);
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_MEM:
+		return _mcp16502_set_mode(rdev, mode, MCP16502_OPMODE_HIB);
+	default:
+		dev_err(&rdev->dev, "invalid suspend target: %d\n",
+			pm_suspend_target_state);
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * mcp16502_set_suspend_enable() - regulator_ops set_suspend_enable
+ */
+static int mcp16502_set_suspend_enable(struct regulator_dev *rdev)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_EN, MCP16502_EN);
+}
+
+/*
+ * mcp16502_set_suspend_disable() - regulator_ops set_suspend_disable
+ */
+static int mcp16502_set_suspend_disable(struct regulator_dev *rdev)
+{
+	struct mcp16502 *mcp = rdev_get_drvdata(rdev);
+	int reg = mcp16502_suspend_get_target_reg(rdev);
+
+	if (reg < 0)
+		return reg;
+
+	return regmap_update_bits(mcp->rmap, reg, MCP16502_EN, 0);
+}
+#endif /* CONFIG_SUSPEND */
+
+static const struct regulator_ops mcp16502_buck_ops = {
+	.list_voltage			= regulator_list_voltage_linear_range,
+	.map_voltage			= regulator_map_voltage_linear_range,
+	.get_voltage_sel		= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel		= regulator_set_voltage_sel_regmap,
+	.enable				= regulator_enable_regmap,
+	.disable			= regulator_disable_regmap,
+	.is_enabled			= regulator_is_enabled_regmap,
+	.get_status			= mcp16502_get_status,
+
+	.set_mode			= mcp16502_set_mode,
+	.get_mode			= mcp16502_get_mode,
+
+#ifdef CONFIG_SUSPEND
+	.set_suspend_voltage		= mcp16502_set_suspend_voltage,
+	.set_suspend_mode		= mcp16502_set_suspend_mode,
+	.set_suspend_enable		= mcp16502_set_suspend_enable,
+	.set_suspend_disable		= mcp16502_set_suspend_disable,
+#endif /* CONFIG_SUSPEND */
+};
+
+/*
+ * LDOs cannot change operating modes.
+ */
+static const struct regulator_ops mcp16502_ldo_ops = {
+	.list_voltage			= regulator_list_voltage_linear_range,
+	.map_voltage			= regulator_map_voltage_linear_range,
+	.get_voltage_sel		= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel		= regulator_set_voltage_sel_regmap,
+	.enable				= regulator_enable_regmap,
+	.disable			= regulator_disable_regmap,
+	.is_enabled			= regulator_is_enabled_regmap,
+	.get_status			= mcp16502_get_status,
+
+#ifdef CONFIG_SUSPEND
+	.set_suspend_voltage		= mcp16502_set_suspend_voltage,
+	.set_suspend_enable		= mcp16502_set_suspend_enable,
+	.set_suspend_disable		= mcp16502_set_suspend_disable,
+#endif /* CONFIG_SUSPEND */
+};
+
+static const struct of_device_id mcp16502_ids[] = {
+	{ .compatible = "microchip,mcp16502", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, mcp16502_ids);
+
+static const struct regulator_linear_range b1l12_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1200000, VDD_LOW_SEL, VDD_HIGH_SEL, 50000),
+};
+
+static const struct regulator_linear_range b234_ranges[] = {
+	REGULATOR_LINEAR_RANGE(600000, VDD_LOW_SEL, VDD_HIGH_SEL, 25000),
+};
+
+static const struct regulator_desc mcp16502_desc[] = {
+	/* MCP16502_REGULATOR(_name, _id, ranges, regulator_ops) */
+	MCP16502_REGULATOR("VDD_IO", BUCK1, b1l12_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_DDR", BUCK2, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_CORE", BUCK3, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("VDD_OTHER", BUCK4, b234_ranges, mcp16502_buck_ops),
+	MCP16502_REGULATOR("LDO1", LDO1, b1l12_ranges, mcp16502_ldo_ops),
+	MCP16502_REGULATOR("LDO2", LDO2, b1l12_ranges, mcp16502_ldo_ops)
+};
+
+static const struct regmap_range mcp16502_ranges[] = {
+	regmap_reg_range(MCP16502_MIN_REG, MCP16502_MAX_REG)
+};
+
+static const struct regmap_access_table mcp16502_yes_reg_table = {
+	.yes_ranges = mcp16502_ranges,
+	.n_yes_ranges = ARRAY_SIZE(mcp16502_ranges),
+};
+
+static const struct regmap_config mcp16502_regmap_config = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+	.max_register	= MCP16502_MAX_REG,
+	.cache_type	= REGCACHE_NONE,
+	.rd_table	= &mcp16502_yes_reg_table,
+	.wr_table	= &mcp16502_yes_reg_table,
+};
+
+/*
+ * set_up_regulators() - initialize all regulators
+ */
+static int setup_regulators(struct mcp16502 *mcp, struct device *dev,
+			    struct regulator_config config)
+{
+	int i;
+
+	for (i = 0; i < NUM_REGULATORS; i++) {
+		mcp->rdev[i] = devm_regulator_register(dev,
+						       &mcp16502_desc[i],
+						       &config);
+		if (IS_ERR(mcp->rdev[i])) {
+			dev_err(dev,
+				"failed to register %s regulator %ld\n",
+				mcp16502_desc[i].name, PTR_ERR(mcp->rdev[i]));
+			return PTR_ERR(mcp->rdev[i]);
+		}
+	}
+
+	return 0;
+}
+
+static int mcp16502_probe(struct i2c_client *client,
+			  const struct i2c_device_id *id)
+{
+	struct regulator_config config = { };
+	struct device *dev;
+	struct mcp16502 *mcp;
+	int ret = 0;
+
+	dev = &client->dev;
+	config.dev = dev;
+
+	mcp = devm_kzalloc(dev, sizeof(*mcp), GFP_KERNEL);
+	if (!mcp)
+		return -ENOMEM;
+
+	mcp->rmap = devm_regmap_init_i2c(client, &mcp16502_regmap_config);
+	if (IS_ERR(mcp->rmap)) {
+		ret = PTR_ERR(mcp->rmap);
+		dev_err(dev, "regmap init failed: %d\n", ret);
+		return ret;
+	}
+
+	i2c_set_clientdata(client, mcp);
+	config.regmap = mcp->rmap;
+	config.driver_data = mcp;
+
+	mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW);
+	if (IS_ERR(mcp->lpm)) {
+		dev_err(dev, "failed to get lpm pin: %ld\n", PTR_ERR(mcp->lpm));
+		return PTR_ERR(mcp->lpm);
+	}
+
+	ret = setup_regulators(mcp, dev, config);
+	if (ret != 0)
+		return ret;
+
+	mcp16502_gpio_set_mode(mcp, MCP16502_OPMODE_ACTIVE);
+
+	return 0;
+}
+
+static const struct i2c_device_id mcp16502_i2c_id[] = {
+	{ "mcp16502", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id);
+
+static struct i2c_driver mcp16502_drv = {
+	.probe		= mcp16502_probe,
+	.driver		= {
+		.name	= "mcp16502-regulator",
+		.of_match_table	= of_match_ptr(mcp16502_ids),
+	},
+	.id_table	= mcp16502_i2c_id,
+};
+
+module_i2c_driver(mcp16502_drv);
+
+MODULE_VERSION("1.0");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MCP16502 PMIC driver");
+MODULE_AUTHOR("Andrei Stefanescu andrei.stefanescu@microchip.com");
-- 
2.7.4

