From: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org, Lei Wang <leiwa@codeaurora.org>,
Sebastian Gottschall <s.gottschall@dd-wrt.com>,
Rick Wu <rwu@codeaurora.org>,
Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Subject: [PATCH] ath10k: enable VHT160 and VHT80+80 modes
Date: Wed, 25 Mar 2020 20:26:09 +0530 [thread overview]
Message-ID: <1585148169-2320-1-git-send-email-ssreeela@codeaurora.org> (raw)
From: Lei Wang <leiwa@codeaurora.org>
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.com
https://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
---
drivers/net/wireless/ath/ath10k/mac.c | 84 +++++++++++++++++++++++++----------
drivers/net/wireless/ath/ath10k/wmi.c | 23 ++++++----
drivers/net/wireless/ath/ath10k/wmi.h | 5 ++-
3 files changed, 80 insertions(+), 32 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 81e148e..7c2e396 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2505,6 +2505,30 @@ static int ath10k_peer_assoc_qos_ap(struct ath10k *ar,
return tx_mcs_set;
}
+static u32 get_160mhz_nss_from_maxrate(int rate)
+{
+ u32 nss;
+
+ switch (rate) {
+ case 780:
+ nss = 1;
+ break;
+ case 1560:
+ nss = 2;
+ break;
+ case 2106:
+ nss = 3; /* not support MCS9 from spec*/
+ break;
+ case 3120:
+ nss = 4;
+ break;
+ default:
+ nss = 0;
+ }
+
+ return nss;
+}
+
static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
struct ieee80211_vif *vif,
struct ieee80211_sta *sta,
@@ -2512,6 +2536,7 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
{
const struct ieee80211_sta_vht_cap *vht_cap = &sta->vht_cap;
struct ath10k_vif *arvif = (void *)vif->drv_priv;
+ struct ath10k_hw_params *hw = &ar->hw_params;
struct cfg80211_chan_def def;
enum nl80211_band band;
const u16 *vht_mcs_mask;
@@ -2578,22 +2603,38 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
arg->peer_vht_rates.tx_mcs_set = ath10k_peer_assoc_h_vht_limit(
__le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map), vht_mcs_mask);
- ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
- sta->addr, arg->peer_max_mpdu, arg->peer_flags);
+ /* Configure bandwidth-NSS mapping to FW
+ * for the chip's tx chains setting on 160Mhz bw
+ */
+ if (arg->peer_phymode == MODE_11AC_VHT160 ||
+ arg->peer_phymode == MODE_11AC_VHT80_80) {
+ u32 rx_nss;
+ u32 max_rate;
- if (arg->peer_vht_rates.rx_max_rate &&
- (sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK)) {
- switch (arg->peer_vht_rates.rx_max_rate) {
- case 1560:
- /* Must be 2x2 at 160Mhz is all it can do. */
- arg->peer_bw_rxnss_override = 2;
- break;
- case 780:
- /* Can only do 1x1 at 160Mhz (Long Guard Interval) */
- arg->peer_bw_rxnss_override = 1;
- break;
+ max_rate = arg->peer_vht_rates.rx_max_rate;
+ rx_nss = get_160mhz_nss_from_maxrate(max_rate);
+
+ if (rx_nss == 0)
+ rx_nss = arg->peer_num_spatial_streams;
+ else
+ rx_nss = min(arg->peer_num_spatial_streams, rx_nss);
+
+ max_rate = hw->vht160_mcs_tx_highest;
+ rx_nss = min(rx_nss, get_160mhz_nss_from_maxrate(max_rate));
+
+ arg->peer_bw_rxnss_override =
+ FIELD_PREP(WMI_PEER_NSS_MAP_ENABLE, 1) |
+ FIELD_PREP(WMI_PEER_NSS_160MHZ_MASK, (rx_nss - 1));
+
+ if (arg->peer_phymode == MODE_11AC_VHT80_80) {
+ arg->peer_bw_rxnss_override |=
+ FIELD_PREP(WMI_PEER_NSS_80_80MHZ_MASK, (rx_nss - 1));
}
}
+ ath10k_dbg(ar, ATH10K_DBG_MAC,
+ "mac vht peer %pM max_mpdu %d flags 0x%x peer_rx_nss_override 0x%x\n",
+ sta->addr, arg->peer_max_mpdu,
+ arg->peer_flags, arg->peer_bw_rxnss_override);
}
static void ath10k_peer_assoc_h_qos(struct ath10k *ar,
@@ -2745,9 +2786,9 @@ static int ath10k_peer_assoc_prepare(struct ath10k *ar,
ath10k_peer_assoc_h_crypto(ar, vif, sta, arg);
ath10k_peer_assoc_h_rates(ar, vif, sta, arg);
ath10k_peer_assoc_h_ht(ar, vif, sta, arg);
+ ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
ath10k_peer_assoc_h_vht(ar, vif, sta, arg);
ath10k_peer_assoc_h_qos(ar, vif, sta, arg);
- ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
return 0;
}
@@ -4561,13 +4602,6 @@ static struct ieee80211_sta_vht_cap ath10k_create_vht_cap(struct ath10k *ar)
vht_cap.cap |= val;
}
- /* Currently the firmware seems to be buggy, don't enable 80+80
- * mode until that's resolved.
- */
- if ((ar->vht_cap_info & IEEE80211_VHT_CAP_SHORT_GI_160) &&
- (ar->vht_cap_info & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK) == 0)
- vht_cap.cap |= IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ;
-
mcs_map = 0;
for (i = 0; i < 8; i++) {
if ((i < ar->num_rf_chains) && (ar->cfg_tx_chainmask & BIT(i)))
@@ -8623,7 +8657,9 @@ void ath10k_mac_destroy(struct ath10k *ar)
.radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
BIT(NL80211_CHAN_WIDTH_20) |
BIT(NL80211_CHAN_WIDTH_40) |
- BIT(NL80211_CHAN_WIDTH_80),
+ BIT(NL80211_CHAN_WIDTH_80) |
+ BIT(NL80211_CHAN_WIDTH_80P80) |
+ BIT(NL80211_CHAN_WIDTH_160),
#endif
},
};
@@ -8641,7 +8677,9 @@ void ath10k_mac_destroy(struct ath10k *ar)
.radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
BIT(NL80211_CHAN_WIDTH_20) |
BIT(NL80211_CHAN_WIDTH_40) |
- BIT(NL80211_CHAN_WIDTH_80),
+ BIT(NL80211_CHAN_WIDTH_80) |
+ BIT(NL80211_CHAN_WIDTH_80P80) |
+ BIT(NL80211_CHAN_WIDTH_160),
#endif
},
};
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 2ea77bb..db6f4c7 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -1714,12 +1714,23 @@ void ath10k_wmi_put_wmi_channel(struct wmi_channel *ch,
if (arg->chan_radar)
flags |= WMI_CHAN_FLAG_DFS;
+ ch->band_center_freq2 = 0;
ch->mhz = __cpu_to_le32(arg->freq);
ch->band_center_freq1 = __cpu_to_le32(arg->band_center_freq1);
if (arg->mode == MODE_11AC_VHT80_80)
ch->band_center_freq2 = __cpu_to_le32(arg->band_center_freq2);
- else
- ch->band_center_freq2 = 0;
+
+ if (arg->mode == MODE_11AC_VHT160) {
+ if (arg->freq > arg->band_center_freq1)
+ ch->band_center_freq1 =
+ __cpu_to_le32(arg->band_center_freq1 + 40);
+ else
+ ch->band_center_freq1 =
+ __cpu_to_le32(arg->band_center_freq1 - 40);
+
+ ch->band_center_freq2 = __cpu_to_le32(arg->band_center_freq1);
+ }
+
ch->min_power = arg->min_power;
ch->max_power = arg->max_power;
ch->reg_power = arg->max_reg_power;
@@ -7628,12 +7639,8 @@ void ath10k_wmi_start_scan_init(struct ath10k *ar,
struct wmi_10_4_peer_assoc_complete_cmd *cmd = buf;
ath10k_wmi_peer_assoc_fill_10_2(ar, buf, arg);
- if (arg->peer_bw_rxnss_override)
- cmd->peer_bw_rxnss_override =
- __cpu_to_le32((arg->peer_bw_rxnss_override - 1) |
- BIT(PEER_BW_RXNSS_OVERRIDE_OFFSET));
- else
- cmd->peer_bw_rxnss_override = 0;
+ cmd->peer_bw_rxnss_override =
+ __cpu_to_le32(arg->peer_bw_rxnss_override);
}
static int
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 972d53d..f722eef3 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -6501,7 +6501,10 @@ struct wmi_10_2_peer_assoc_complete_cmd {
__le32 info0; /* WMI_PEER_ASSOC_INFO0_ */
} __packed;
-#define PEER_BW_RXNSS_OVERRIDE_OFFSET 31
+/* NSS Mapping to FW */
+#define WMI_PEER_NSS_MAP_ENABLE BIT(31)
+#define WMI_PEER_NSS_160MHZ_MASK GENMASK(2, 0)
+#define WMI_PEER_NSS_80_80MHZ_MASK GENMASK(5, 3)
struct wmi_10_4_peer_assoc_complete_cmd {
struct wmi_10_2_peer_assoc_complete_cmd cmd;
--
1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
To: ath10k@lists.infradead.org
Cc: Lei Wang <leiwa@codeaurora.org>,
Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>,
Rick Wu <rwu@codeaurora.org>,
linux-wireless@vger.kernel.org,
Sebastian Gottschall <s.gottschall@dd-wrt.com>
Subject: [PATCH] ath10k: enable VHT160 and VHT80+80 modes
Date: Wed, 25 Mar 2020 20:26:09 +0530 [thread overview]
Message-ID: <1585148169-2320-1-git-send-email-ssreeela@codeaurora.org> (raw)
From: Lei Wang <leiwa@codeaurora.org>
Set right channel frequencies in VHT160 mode according to the VHT160
interoperability workaround added as part of IEEE Std 802.11™-2016 in
"Table 9-252—VHT Operation Information subfields", band_center_freq2
corresponds to CCFS1 in Table 9-253. Previous implementation
(band_center_freq2 = 0 for VHT160) is only deprecated.
Enable VHT80+80 mode and set the proper peer RX nss value for VHT160 and
VHT80+80 mode.
Based on patches by Sebastian Gottschall:
https://lkml.kernel.org/r/20180704095444.662-1-s.gottschall@dd-wrt.com
https://lkml.kernel.org/r/20180704120519.6479-1-s.gottschall@dd-wrt.com
Tested: qca9984 with firmware ver 10.4-3.10-00047
Co-developed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Co-developed-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Rick Wu <rwu@codeaurora.org>
Signed-off-by: Lei Wang <leiwa@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
---
drivers/net/wireless/ath/ath10k/mac.c | 84 +++++++++++++++++++++++++----------
drivers/net/wireless/ath/ath10k/wmi.c | 23 ++++++----
drivers/net/wireless/ath/ath10k/wmi.h | 5 ++-
3 files changed, 80 insertions(+), 32 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index 81e148e..7c2e396 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -2505,6 +2505,30 @@ static int ath10k_peer_assoc_qos_ap(struct ath10k *ar,
return tx_mcs_set;
}
+static u32 get_160mhz_nss_from_maxrate(int rate)
+{
+ u32 nss;
+
+ switch (rate) {
+ case 780:
+ nss = 1;
+ break;
+ case 1560:
+ nss = 2;
+ break;
+ case 2106:
+ nss = 3; /* not support MCS9 from spec*/
+ break;
+ case 3120:
+ nss = 4;
+ break;
+ default:
+ nss = 0;
+ }
+
+ return nss;
+}
+
static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
struct ieee80211_vif *vif,
struct ieee80211_sta *sta,
@@ -2512,6 +2536,7 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
{
const struct ieee80211_sta_vht_cap *vht_cap = &sta->vht_cap;
struct ath10k_vif *arvif = (void *)vif->drv_priv;
+ struct ath10k_hw_params *hw = &ar->hw_params;
struct cfg80211_chan_def def;
enum nl80211_band band;
const u16 *vht_mcs_mask;
@@ -2578,22 +2603,38 @@ static void ath10k_peer_assoc_h_vht(struct ath10k *ar,
arg->peer_vht_rates.tx_mcs_set = ath10k_peer_assoc_h_vht_limit(
__le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map), vht_mcs_mask);
- ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
- sta->addr, arg->peer_max_mpdu, arg->peer_flags);
+ /* Configure bandwidth-NSS mapping to FW
+ * for the chip's tx chains setting on 160Mhz bw
+ */
+ if (arg->peer_phymode == MODE_11AC_VHT160 ||
+ arg->peer_phymode == MODE_11AC_VHT80_80) {
+ u32 rx_nss;
+ u32 max_rate;
- if (arg->peer_vht_rates.rx_max_rate &&
- (sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK)) {
- switch (arg->peer_vht_rates.rx_max_rate) {
- case 1560:
- /* Must be 2x2 at 160Mhz is all it can do. */
- arg->peer_bw_rxnss_override = 2;
- break;
- case 780:
- /* Can only do 1x1 at 160Mhz (Long Guard Interval) */
- arg->peer_bw_rxnss_override = 1;
- break;
+ max_rate = arg->peer_vht_rates.rx_max_rate;
+ rx_nss = get_160mhz_nss_from_maxrate(max_rate);
+
+ if (rx_nss == 0)
+ rx_nss = arg->peer_num_spatial_streams;
+ else
+ rx_nss = min(arg->peer_num_spatial_streams, rx_nss);
+
+ max_rate = hw->vht160_mcs_tx_highest;
+ rx_nss = min(rx_nss, get_160mhz_nss_from_maxrate(max_rate));
+
+ arg->peer_bw_rxnss_override =
+ FIELD_PREP(WMI_PEER_NSS_MAP_ENABLE, 1) |
+ FIELD_PREP(WMI_PEER_NSS_160MHZ_MASK, (rx_nss - 1));
+
+ if (arg->peer_phymode == MODE_11AC_VHT80_80) {
+ arg->peer_bw_rxnss_override |=
+ FIELD_PREP(WMI_PEER_NSS_80_80MHZ_MASK, (rx_nss - 1));
}
}
+ ath10k_dbg(ar, ATH10K_DBG_MAC,
+ "mac vht peer %pM max_mpdu %d flags 0x%x peer_rx_nss_override 0x%x\n",
+ sta->addr, arg->peer_max_mpdu,
+ arg->peer_flags, arg->peer_bw_rxnss_override);
}
static void ath10k_peer_assoc_h_qos(struct ath10k *ar,
@@ -2745,9 +2786,9 @@ static int ath10k_peer_assoc_prepare(struct ath10k *ar,
ath10k_peer_assoc_h_crypto(ar, vif, sta, arg);
ath10k_peer_assoc_h_rates(ar, vif, sta, arg);
ath10k_peer_assoc_h_ht(ar, vif, sta, arg);
+ ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
ath10k_peer_assoc_h_vht(ar, vif, sta, arg);
ath10k_peer_assoc_h_qos(ar, vif, sta, arg);
- ath10k_peer_assoc_h_phymode(ar, vif, sta, arg);
return 0;
}
@@ -4561,13 +4602,6 @@ static struct ieee80211_sta_vht_cap ath10k_create_vht_cap(struct ath10k *ar)
vht_cap.cap |= val;
}
- /* Currently the firmware seems to be buggy, don't enable 80+80
- * mode until that's resolved.
- */
- if ((ar->vht_cap_info & IEEE80211_VHT_CAP_SHORT_GI_160) &&
- (ar->vht_cap_info & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK) == 0)
- vht_cap.cap |= IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ;
-
mcs_map = 0;
for (i = 0; i < 8; i++) {
if ((i < ar->num_rf_chains) && (ar->cfg_tx_chainmask & BIT(i)))
@@ -8623,7 +8657,9 @@ void ath10k_mac_destroy(struct ath10k *ar)
.radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
BIT(NL80211_CHAN_WIDTH_20) |
BIT(NL80211_CHAN_WIDTH_40) |
- BIT(NL80211_CHAN_WIDTH_80),
+ BIT(NL80211_CHAN_WIDTH_80) |
+ BIT(NL80211_CHAN_WIDTH_80P80) |
+ BIT(NL80211_CHAN_WIDTH_160),
#endif
},
};
@@ -8641,7 +8677,9 @@ void ath10k_mac_destroy(struct ath10k *ar)
.radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
BIT(NL80211_CHAN_WIDTH_20) |
BIT(NL80211_CHAN_WIDTH_40) |
- BIT(NL80211_CHAN_WIDTH_80),
+ BIT(NL80211_CHAN_WIDTH_80) |
+ BIT(NL80211_CHAN_WIDTH_80P80) |
+ BIT(NL80211_CHAN_WIDTH_160),
#endif
},
};
diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index 2ea77bb..db6f4c7 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -1714,12 +1714,23 @@ void ath10k_wmi_put_wmi_channel(struct wmi_channel *ch,
if (arg->chan_radar)
flags |= WMI_CHAN_FLAG_DFS;
+ ch->band_center_freq2 = 0;
ch->mhz = __cpu_to_le32(arg->freq);
ch->band_center_freq1 = __cpu_to_le32(arg->band_center_freq1);
if (arg->mode == MODE_11AC_VHT80_80)
ch->band_center_freq2 = __cpu_to_le32(arg->band_center_freq2);
- else
- ch->band_center_freq2 = 0;
+
+ if (arg->mode == MODE_11AC_VHT160) {
+ if (arg->freq > arg->band_center_freq1)
+ ch->band_center_freq1 =
+ __cpu_to_le32(arg->band_center_freq1 + 40);
+ else
+ ch->band_center_freq1 =
+ __cpu_to_le32(arg->band_center_freq1 - 40);
+
+ ch->band_center_freq2 = __cpu_to_le32(arg->band_center_freq1);
+ }
+
ch->min_power = arg->min_power;
ch->max_power = arg->max_power;
ch->reg_power = arg->max_reg_power;
@@ -7628,12 +7639,8 @@ void ath10k_wmi_start_scan_init(struct ath10k *ar,
struct wmi_10_4_peer_assoc_complete_cmd *cmd = buf;
ath10k_wmi_peer_assoc_fill_10_2(ar, buf, arg);
- if (arg->peer_bw_rxnss_override)
- cmd->peer_bw_rxnss_override =
- __cpu_to_le32((arg->peer_bw_rxnss_override - 1) |
- BIT(PEER_BW_RXNSS_OVERRIDE_OFFSET));
- else
- cmd->peer_bw_rxnss_override = 0;
+ cmd->peer_bw_rxnss_override =
+ __cpu_to_le32(arg->peer_bw_rxnss_override);
}
static int
diff --git a/drivers/net/wireless/ath/ath10k/wmi.h b/drivers/net/wireless/ath/ath10k/wmi.h
index 972d53d..f722eef3 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.h
+++ b/drivers/net/wireless/ath/ath10k/wmi.h
@@ -6501,7 +6501,10 @@ struct wmi_10_2_peer_assoc_complete_cmd {
__le32 info0; /* WMI_PEER_ASSOC_INFO0_ */
} __packed;
-#define PEER_BW_RXNSS_OVERRIDE_OFFSET 31
+/* NSS Mapping to FW */
+#define WMI_PEER_NSS_MAP_ENABLE BIT(31)
+#define WMI_PEER_NSS_160MHZ_MASK GENMASK(2, 0)
+#define WMI_PEER_NSS_80_80MHZ_MASK GENMASK(5, 3)
struct wmi_10_4_peer_assoc_complete_cmd {
struct wmi_10_2_peer_assoc_complete_cmd cmd;
--
1.9.1
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next reply other threads:[~2020-03-25 14:58 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-25 14:56 Sowmiya Sree Elavalagan [this message]
2020-03-25 14:56 ` [PATCH] ath10k: enable VHT160 and VHT80+80 modes Sowmiya Sree Elavalagan
2020-03-26 9:59 ` Kalle Valo
2020-03-26 9:59 ` Kalle Valo
[not found] ` <20200326095907.5326BC433BA@smtp.codeaurora.org>
2020-03-26 13:15 ` ssreeela
2020-03-26 13:15 ` ssreeela
2020-03-27 11:25 ` Kalle Valo
2020-03-27 11:25 ` Kalle Valo
2020-03-30 9:22 ` ssreeela
2020-03-30 9:22 ` ssreeela
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1585148169-2320-1-git-send-email-ssreeela@codeaurora.org \
--to=ssreeela@codeaurora.org \
--cc=ath10k@lists.infradead.org \
--cc=leiwa@codeaurora.org \
--cc=linux-wireless@vger.kernel.org \
--cc=rwu@codeaurora.org \
--cc=s.gottschall@dd-wrt.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.