From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-phy@lists.infradead.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Eddie Hung <eddie.hung@mediatek.com>
Subject: [PATCH v4 2/3] phy: phy-mtk-tphy: support new hardware version
Date: Fri, 23 Jul 2021 16:22:41 +0800 [thread overview]
Message-ID: <1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com> (raw)
In-Reply-To: <1627028562-23584-1-git-send-email-chunfeng.yun@mediatek.com>
The PHYA arch is updated, and doesn't support slew rate calibrate
anymore on 7nm or advanced process, add a new version number to
support it.
Note: the FreqMeter bank is not used but reserved.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~4: no changes
---
drivers/phy/mediatek/phy-mtk-tphy.c | 40 +++++++++++++++++++++--------
1 file changed, 29 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 731c483a04de..42a1174da6cc 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -27,7 +27,8 @@
#define SSUSB_SIFSLV_V1_U3PHYD 0x000
#define SSUSB_SIFSLV_V1_U3PHYA 0x200
-/* version V2 sub-banks offset base address */
+/* version V2/V3 sub-banks offset base address */
+/* V3: U2FREQ is not used anymore, but reserved */
/* u2 phy banks */
#define SSUSB_SIFSLV_V2_MISC 0x000
#define SSUSB_SIFSLV_V2_U2FREQ 0x100
@@ -270,6 +271,7 @@
enum mtk_phy_version {
MTK_PHY_V1 = 1,
MTK_PHY_V2,
+ MTK_PHY_V3,
};
struct mtk_phy_pdata {
@@ -330,6 +332,10 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
int fm_out;
u32 tmp;
+ /* HW V3 doesn't support slew rate cal anymore */
+ if (tphy->pdata->version == MTK_PHY_V3)
+ return;
+
/* use force value */
if (instance->eye_src)
return;
@@ -878,7 +884,7 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
writel(tmp, com + U3P_U2PHYBC12C);
}
- if (instance->eye_src) {
+ if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) {
tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
@@ -1042,11 +1048,15 @@ static struct phy *mtk_phy_xlate(struct device *dev,
return ERR_PTR(-EINVAL);
}
- if (tphy->pdata->version == MTK_PHY_V1) {
+ switch (tphy->pdata->version) {
+ case MTK_PHY_V1:
phy_v1_banks_init(tphy, instance);
- } else if (tphy->pdata->version == MTK_PHY_V2) {
+ break;
+ case MTK_PHY_V2:
+ case MTK_PHY_V3:
phy_v2_banks_init(tphy, instance);
- } else {
+ break;
+ default:
dev_err(dev, "phy version is not supported\n");
return ERR_PTR(-EINVAL);
}
@@ -1075,6 +1085,10 @@ static const struct mtk_phy_pdata tphy_v2_pdata = {
.version = MTK_PHY_V2,
};
+static const struct mtk_phy_pdata tphy_v3_pdata = {
+ .version = MTK_PHY_V3,
+};
+
static const struct mtk_phy_pdata mt8173_pdata = {
.avoid_rx_sen_degradation = true,
.version = MTK_PHY_V1,
@@ -1086,6 +1100,7 @@ static const struct of_device_id mtk_tphy_id_table[] = {
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
+ { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
{ },
};
MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
@@ -1129,12 +1144,15 @@ static int mtk_tphy_probe(struct platform_device *pdev)
}
}
- tphy->src_ref_clk = U3P_REF_CLK;
- tphy->src_coef = U3P_SLEW_RATE_COEF;
- /* update parameters of slew rate calibrate if exist */
- device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
- &tphy->src_ref_clk);
- device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
+ if (tphy->pdata->version < MTK_PHY_V3) {
+ tphy->src_ref_clk = U3P_REF_CLK;
+ tphy->src_coef = U3P_SLEW_RATE_COEF;
+ /* update parameters of slew rate calibrate if exist */
+ device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
+ &tphy->src_ref_clk);
+ device_property_read_u32(dev, "mediatek,src-coef",
+ &tphy->src_coef);
+ }
port = 0;
for_each_child_of_node(np, child_np) {
--
2.18.0
WARNING: multiple messages have this Message-ID (diff)
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-phy@lists.infradead.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Eddie Hung <eddie.hung@mediatek.com>
Subject: [PATCH v4 2/3] phy: phy-mtk-tphy: support new hardware version
Date: Fri, 23 Jul 2021 16:22:41 +0800 [thread overview]
Message-ID: <1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com> (raw)
In-Reply-To: <1627028562-23584-1-git-send-email-chunfeng.yun@mediatek.com>
The PHYA arch is updated, and doesn't support slew rate calibrate
anymore on 7nm or advanced process, add a new version number to
support it.
Note: the FreqMeter bank is not used but reserved.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~4: no changes
---
drivers/phy/mediatek/phy-mtk-tphy.c | 40 +++++++++++++++++++++--------
1 file changed, 29 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 731c483a04de..42a1174da6cc 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -27,7 +27,8 @@
#define SSUSB_SIFSLV_V1_U3PHYD 0x000
#define SSUSB_SIFSLV_V1_U3PHYA 0x200
-/* version V2 sub-banks offset base address */
+/* version V2/V3 sub-banks offset base address */
+/* V3: U2FREQ is not used anymore, but reserved */
/* u2 phy banks */
#define SSUSB_SIFSLV_V2_MISC 0x000
#define SSUSB_SIFSLV_V2_U2FREQ 0x100
@@ -270,6 +271,7 @@
enum mtk_phy_version {
MTK_PHY_V1 = 1,
MTK_PHY_V2,
+ MTK_PHY_V3,
};
struct mtk_phy_pdata {
@@ -330,6 +332,10 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
int fm_out;
u32 tmp;
+ /* HW V3 doesn't support slew rate cal anymore */
+ if (tphy->pdata->version == MTK_PHY_V3)
+ return;
+
/* use force value */
if (instance->eye_src)
return;
@@ -878,7 +884,7 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
writel(tmp, com + U3P_U2PHYBC12C);
}
- if (instance->eye_src) {
+ if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) {
tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
@@ -1042,11 +1048,15 @@ static struct phy *mtk_phy_xlate(struct device *dev,
return ERR_PTR(-EINVAL);
}
- if (tphy->pdata->version == MTK_PHY_V1) {
+ switch (tphy->pdata->version) {
+ case MTK_PHY_V1:
phy_v1_banks_init(tphy, instance);
- } else if (tphy->pdata->version == MTK_PHY_V2) {
+ break;
+ case MTK_PHY_V2:
+ case MTK_PHY_V3:
phy_v2_banks_init(tphy, instance);
- } else {
+ break;
+ default:
dev_err(dev, "phy version is not supported\n");
return ERR_PTR(-EINVAL);
}
@@ -1075,6 +1085,10 @@ static const struct mtk_phy_pdata tphy_v2_pdata = {
.version = MTK_PHY_V2,
};
+static const struct mtk_phy_pdata tphy_v3_pdata = {
+ .version = MTK_PHY_V3,
+};
+
static const struct mtk_phy_pdata mt8173_pdata = {
.avoid_rx_sen_degradation = true,
.version = MTK_PHY_V1,
@@ -1086,6 +1100,7 @@ static const struct of_device_id mtk_tphy_id_table[] = {
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
+ { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
{ },
};
MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
@@ -1129,12 +1144,15 @@ static int mtk_tphy_probe(struct platform_device *pdev)
}
}
- tphy->src_ref_clk = U3P_REF_CLK;
- tphy->src_coef = U3P_SLEW_RATE_COEF;
- /* update parameters of slew rate calibrate if exist */
- device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
- &tphy->src_ref_clk);
- device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
+ if (tphy->pdata->version < MTK_PHY_V3) {
+ tphy->src_ref_clk = U3P_REF_CLK;
+ tphy->src_coef = U3P_SLEW_RATE_COEF;
+ /* update parameters of slew rate calibrate if exist */
+ device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
+ &tphy->src_ref_clk);
+ device_property_read_u32(dev, "mediatek,src-coef",
+ &tphy->src_coef);
+ }
port = 0;
for_each_child_of_node(np, child_np) {
--
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek
WARNING: multiple messages have this Message-ID (diff)
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-phy@lists.infradead.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Eddie Hung <eddie.hung@mediatek.com>
Subject: [PATCH v4 2/3] phy: phy-mtk-tphy: support new hardware version
Date: Fri, 23 Jul 2021 16:22:41 +0800 [thread overview]
Message-ID: <1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com> (raw)
In-Reply-To: <1627028562-23584-1-git-send-email-chunfeng.yun@mediatek.com>
The PHYA arch is updated, and doesn't support slew rate calibrate
anymore on 7nm or advanced process, add a new version number to
support it.
Note: the FreqMeter bank is not used but reserved.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~4: no changes
---
drivers/phy/mediatek/phy-mtk-tphy.c | 40 +++++++++++++++++++++--------
1 file changed, 29 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 731c483a04de..42a1174da6cc 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -27,7 +27,8 @@
#define SSUSB_SIFSLV_V1_U3PHYD 0x000
#define SSUSB_SIFSLV_V1_U3PHYA 0x200
-/* version V2 sub-banks offset base address */
+/* version V2/V3 sub-banks offset base address */
+/* V3: U2FREQ is not used anymore, but reserved */
/* u2 phy banks */
#define SSUSB_SIFSLV_V2_MISC 0x000
#define SSUSB_SIFSLV_V2_U2FREQ 0x100
@@ -270,6 +271,7 @@
enum mtk_phy_version {
MTK_PHY_V1 = 1,
MTK_PHY_V2,
+ MTK_PHY_V3,
};
struct mtk_phy_pdata {
@@ -330,6 +332,10 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
int fm_out;
u32 tmp;
+ /* HW V3 doesn't support slew rate cal anymore */
+ if (tphy->pdata->version == MTK_PHY_V3)
+ return;
+
/* use force value */
if (instance->eye_src)
return;
@@ -878,7 +884,7 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
writel(tmp, com + U3P_U2PHYBC12C);
}
- if (instance->eye_src) {
+ if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) {
tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
@@ -1042,11 +1048,15 @@ static struct phy *mtk_phy_xlate(struct device *dev,
return ERR_PTR(-EINVAL);
}
- if (tphy->pdata->version == MTK_PHY_V1) {
+ switch (tphy->pdata->version) {
+ case MTK_PHY_V1:
phy_v1_banks_init(tphy, instance);
- } else if (tphy->pdata->version == MTK_PHY_V2) {
+ break;
+ case MTK_PHY_V2:
+ case MTK_PHY_V3:
phy_v2_banks_init(tphy, instance);
- } else {
+ break;
+ default:
dev_err(dev, "phy version is not supported\n");
return ERR_PTR(-EINVAL);
}
@@ -1075,6 +1085,10 @@ static const struct mtk_phy_pdata tphy_v2_pdata = {
.version = MTK_PHY_V2,
};
+static const struct mtk_phy_pdata tphy_v3_pdata = {
+ .version = MTK_PHY_V3,
+};
+
static const struct mtk_phy_pdata mt8173_pdata = {
.avoid_rx_sen_degradation = true,
.version = MTK_PHY_V1,
@@ -1086,6 +1100,7 @@ static const struct of_device_id mtk_tphy_id_table[] = {
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
+ { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
{ },
};
MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
@@ -1129,12 +1144,15 @@ static int mtk_tphy_probe(struct platform_device *pdev)
}
}
- tphy->src_ref_clk = U3P_REF_CLK;
- tphy->src_coef = U3P_SLEW_RATE_COEF;
- /* update parameters of slew rate calibrate if exist */
- device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
- &tphy->src_ref_clk);
- device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
+ if (tphy->pdata->version < MTK_PHY_V3) {
+ tphy->src_ref_clk = U3P_REF_CLK;
+ tphy->src_coef = U3P_SLEW_RATE_COEF;
+ /* update parameters of slew rate calibrate if exist */
+ device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
+ &tphy->src_ref_clk);
+ device_property_read_u32(dev, "mediatek,src-coef",
+ &tphy->src_coef);
+ }
port = 0;
for_each_child_of_node(np, child_np) {
--
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Rob Herring <robh+dt@kernel.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
<linux-phy@lists.infradead.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
Eddie Hung <eddie.hung@mediatek.com>
Subject: [PATCH v4 2/3] phy: phy-mtk-tphy: support new hardware version
Date: Fri, 23 Jul 2021 16:22:41 +0800 [thread overview]
Message-ID: <1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com> (raw)
In-Reply-To: <1627028562-23584-1-git-send-email-chunfeng.yun@mediatek.com>
The PHYA arch is updated, and doesn't support slew rate calibrate
anymore on 7nm or advanced process, add a new version number to
support it.
Note: the FreqMeter bank is not used but reserved.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2~4: no changes
---
drivers/phy/mediatek/phy-mtk-tphy.c | 40 +++++++++++++++++++++--------
1 file changed, 29 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 731c483a04de..42a1174da6cc 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -27,7 +27,8 @@
#define SSUSB_SIFSLV_V1_U3PHYD 0x000
#define SSUSB_SIFSLV_V1_U3PHYA 0x200
-/* version V2 sub-banks offset base address */
+/* version V2/V3 sub-banks offset base address */
+/* V3: U2FREQ is not used anymore, but reserved */
/* u2 phy banks */
#define SSUSB_SIFSLV_V2_MISC 0x000
#define SSUSB_SIFSLV_V2_U2FREQ 0x100
@@ -270,6 +271,7 @@
enum mtk_phy_version {
MTK_PHY_V1 = 1,
MTK_PHY_V2,
+ MTK_PHY_V3,
};
struct mtk_phy_pdata {
@@ -330,6 +332,10 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
int fm_out;
u32 tmp;
+ /* HW V3 doesn't support slew rate cal anymore */
+ if (tphy->pdata->version == MTK_PHY_V3)
+ return;
+
/* use force value */
if (instance->eye_src)
return;
@@ -878,7 +884,7 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
writel(tmp, com + U3P_U2PHYBC12C);
}
- if (instance->eye_src) {
+ if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) {
tmp = readl(com + U3P_USBPHYACR5);
tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
@@ -1042,11 +1048,15 @@ static struct phy *mtk_phy_xlate(struct device *dev,
return ERR_PTR(-EINVAL);
}
- if (tphy->pdata->version == MTK_PHY_V1) {
+ switch (tphy->pdata->version) {
+ case MTK_PHY_V1:
phy_v1_banks_init(tphy, instance);
- } else if (tphy->pdata->version == MTK_PHY_V2) {
+ break;
+ case MTK_PHY_V2:
+ case MTK_PHY_V3:
phy_v2_banks_init(tphy, instance);
- } else {
+ break;
+ default:
dev_err(dev, "phy version is not supported\n");
return ERR_PTR(-EINVAL);
}
@@ -1075,6 +1085,10 @@ static const struct mtk_phy_pdata tphy_v2_pdata = {
.version = MTK_PHY_V2,
};
+static const struct mtk_phy_pdata tphy_v3_pdata = {
+ .version = MTK_PHY_V3,
+};
+
static const struct mtk_phy_pdata mt8173_pdata = {
.avoid_rx_sen_degradation = true,
.version = MTK_PHY_V1,
@@ -1086,6 +1100,7 @@ static const struct of_device_id mtk_tphy_id_table[] = {
{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
+ { .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
{ },
};
MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
@@ -1129,12 +1144,15 @@ static int mtk_tphy_probe(struct platform_device *pdev)
}
}
- tphy->src_ref_clk = U3P_REF_CLK;
- tphy->src_coef = U3P_SLEW_RATE_COEF;
- /* update parameters of slew rate calibrate if exist */
- device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
- &tphy->src_ref_clk);
- device_property_read_u32(dev, "mediatek,src-coef", &tphy->src_coef);
+ if (tphy->pdata->version < MTK_PHY_V3) {
+ tphy->src_ref_clk = U3P_REF_CLK;
+ tphy->src_coef = U3P_SLEW_RATE_COEF;
+ /* update parameters of slew rate calibrate if exist */
+ device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
+ &tphy->src_ref_clk);
+ device_property_read_u32(dev, "mediatek,src-coef",
+ &tphy->src_coef);
+ }
port = 0;
for_each_child_of_node(np, child_np) {
--
2.18.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
next prev parent reply other threads:[~2021-07-23 8:23 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-23 8:22 [PATCH v4 1/3] dt-bindings: phy: mediatek: tphy: add support hardware version 3 Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun [this message]
2021-07-23 8:22 ` [PATCH v4 2/3] phy: phy-mtk-tphy: support new hardware version Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` [PATCH v4 3/3] phy: phy-mtk-tphy: add support mt8195 Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-07-23 8:22 ` Chunfeng Yun
2021-08-06 11:59 ` [PATCH v4 1/3] dt-bindings: phy: mediatek: tphy: add support hardware version 3 Vinod Koul
2021-08-06 11:59 ` Vinod Koul
2021-08-06 11:59 ` Vinod Koul
2021-08-06 11:59 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1627028562-23584-2-git-send-email-chunfeng.yun@mediatek.com \
--to=chunfeng.yun@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=eddie.hung@mediatek.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-phy@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.