From: Tony Lindgren <tony@atomide.com>
To: "Varadarajan, Charulatha" <charu@ti.com>
Cc: linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
khilman@deeprootsystems.com, paul@pwsan.com, b-cousson@ti.com,
p-basak2@ti.com, Cory Maccarrone <darkstar6262@gmail.com>,
Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Subject: Re: [PATCH v8 00/11] OMAP: GPIO: Implement GPIO as platform device
Date: Tue, 7 Dec 2010 16:54:52 -0800 [thread overview]
Message-ID: <20101208005452.GG17435@atomide.com> (raw)
In-Reply-To: <1290689318-10191-1-git-send-email-charu@ti.com>
* Varadarajan, Charulatha <charu@ti.com> [101125 04:39]:
> Implement OMAP GPIO module in platform device model. OMAP2+ specific GPIO
> module uses hwmod FW.
I'll add the following patch underneath this series as otherwise some
gpio_request calls will fail after this series.
Regards,
Tony
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 7 Dec 2010 16:26:55 -0800
Subject: [PATCH] omap: Fix gpio_request calls to happen as arch_initcall
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 149fdd3..295ab67 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -120,6 +120,15 @@ static struct resource smc91x_resources[] = {
},
};
+static void __init fsample_init_smc91x(void)
+{
+ fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+ fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+ H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+}
+
static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
@@ -285,6 +294,8 @@ static struct omap_board_config_kernel fsample_config[] = {
static void __init omap_fsample_init(void)
{
+ fsample_init_smc91x();
+
if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
@@ -312,21 +323,11 @@ static void __init omap_fsample_init(void)
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init fsample_init_smc91x(void)
-{
- fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
static void __init omap_fsample_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- fsample_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 197adb4..dd35efd 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -375,7 +375,6 @@ static void __init h2_init_irq(void)
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- h2_init_smc91x();
}
static struct omap_usb_config h2_usb_config __initdata = {
@@ -403,6 +402,8 @@ static struct omap_board_config_kernel h2_config[] __initdata = {
static void __init h2_init(void)
{
+ h2_init_smc91x();
+
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled at probe time.
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 9126e3e..7871919 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -264,6 +264,15 @@ static struct platform_device smc91x_device = {
.resource = smc91x_resources,
};
+static void __init h3_init_smc91x(void)
+{
+ omap_cfg_reg(W15_1710_GPIO40);
+ if (gpio_request(40, "SMC91x irq") < 0) {
+ printk("Error requesting gpio 40 for smc91x irq\n");
+ return;
+ }
+}
+
#define GPTIMER_BASE 0xFFFB1400
#define GPTIMER_REGS(x) (0xFFFB1400 + (x * 0x800))
#define GPTIMER_REGS_SIZE 0x46
@@ -376,6 +385,8 @@ static struct i2c_board_info __initdata h3_i2c_board_info[] = {
static void __init h3_init(void)
{
+ h3_init_smc91x();
+
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled at probe time.
@@ -422,21 +433,11 @@ static void __init h3_init(void)
h3_mmc_init();
}
-static void __init h3_init_smc91x(void)
-{
- omap_cfg_reg(W15_1710_GPIO40);
- if (gpio_request(40, "SMC91x irq") < 0) {
- printk("Error requesting gpio 40 for smc91x irq\n");
- return;
- }
-}
-
static void __init h3_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- h3_init_smc91x();
}
static void __init h3_map_io(void)
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index dc2b86f..0feaa67 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -296,7 +296,6 @@ static void __init innovator_init_irq(void)
omap1510_fpga_init_irq();
}
#endif
- innovator_init_smc91x();
}
#ifdef CONFIG_ARCH_OMAP15XX
@@ -387,6 +386,8 @@ static struct omap_board_config_kernel innovator_config[] = {
static void __init innovator_init(void)
{
+ innovator_init_smc91x();
+
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
unsigned char reg;
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index e9dd791..30bdbdb 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -284,8 +284,6 @@ static void __init osk_init_irq(void)
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- osk_init_smc91x();
- osk_init_cf();
}
static struct omap_usb_config osk_usb_config __initdata = {
@@ -541,6 +539,9 @@ static void __init osk_init(void)
{
u32 l;
+ osk_init_smc91x();
+ osk_init_cf();
+
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index a8d16a2..07660be 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -251,8 +251,19 @@ static struct omap_board_config_kernel perseus2_config[] __initdata = {
{ OMAP_TAG_LCD, &perseus2_lcd_config },
};
+static void __init perseus2_init_smc91x(void)
+{
+ fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+ fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+ H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+}
+
static void __init omap_perseus2_init(void)
{
+ perseus2_init_smc91x();
+
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
@@ -280,21 +291,11 @@ static void __init omap_perseus2_init(void)
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init perseus2_init_smc91x(void)
-{
- fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
static void __init omap_perseus2_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- perseus2_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 2c6db1a..6ae777e 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -281,7 +281,6 @@ static void __init omap_apollon_init_irq(void)
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
- apollon_init_smc91x();
}
static void __init apollon_led_init(void)
@@ -324,6 +323,7 @@ static void __init omap_apollon_init(void)
omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
+ apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index 001fd97..3dab44e 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -295,7 +295,6 @@ static void __init omap_ldp_init_irq(void)
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
- ldp_init_smsc911x();
}
static struct twl4030_usb_data ldp_usb_data = {
@@ -426,6 +425,7 @@ static struct mtd_partition ldp_nand_partitions[] = {
static void __init omap_ldp_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+ ldp_init_smsc911x();
omap_i2c_init();
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
ts_gpio = 54;
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v8 00/11] OMAP: GPIO: Implement GPIO as platform device
Date: Tue, 7 Dec 2010 16:54:52 -0800 [thread overview]
Message-ID: <20101208005452.GG17435@atomide.com> (raw)
In-Reply-To: <1290689318-10191-1-git-send-email-charu@ti.com>
* Varadarajan, Charulatha <charu@ti.com> [101125 04:39]:
> Implement OMAP GPIO module in platform device model. OMAP2+ specific GPIO
> module uses hwmod FW.
I'll add the following patch underneath this series as otherwise some
gpio_request calls will fail after this series.
Regards,
Tony
From: Tony Lindgren <tony@atomide.com>
Date: Tue, 7 Dec 2010 16:26:55 -0800
Subject: [PATCH] omap: Fix gpio_request calls to happen as arch_initcall
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 149fdd3..295ab67 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -120,6 +120,15 @@ static struct resource smc91x_resources[] = {
},
};
+static void __init fsample_init_smc91x(void)
+{
+ fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+ fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+ H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+}
+
static struct mtd_partition nor_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
@@ -285,6 +294,8 @@ static struct omap_board_config_kernel fsample_config[] = {
static void __init omap_fsample_init(void)
{
+ fsample_init_smc91x();
+
if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
@@ -312,21 +323,11 @@ static void __init omap_fsample_init(void)
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init fsample_init_smc91x(void)
-{
- fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
static void __init omap_fsample_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- fsample_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 197adb4..dd35efd 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -375,7 +375,6 @@ static void __init h2_init_irq(void)
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- h2_init_smc91x();
}
static struct omap_usb_config h2_usb_config __initdata = {
@@ -403,6 +402,8 @@ static struct omap_board_config_kernel h2_config[] __initdata = {
static void __init h2_init(void)
{
+ h2_init_smc91x();
+
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled at probe time.
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 9126e3e..7871919 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -264,6 +264,15 @@ static struct platform_device smc91x_device = {
.resource = smc91x_resources,
};
+static void __init h3_init_smc91x(void)
+{
+ omap_cfg_reg(W15_1710_GPIO40);
+ if (gpio_request(40, "SMC91x irq") < 0) {
+ printk("Error requesting gpio 40 for smc91x irq\n");
+ return;
+ }
+}
+
#define GPTIMER_BASE 0xFFFB1400
#define GPTIMER_REGS(x) (0xFFFB1400 + (x * 0x800))
#define GPTIMER_REGS_SIZE 0x46
@@ -376,6 +385,8 @@ static struct i2c_board_info __initdata h3_i2c_board_info[] = {
static void __init h3_init(void)
{
+ h3_init_smc91x();
+
/* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
* to address 0 by a dip switch), NAND on CS2B. The NAND driver will
* notice whether a NAND chip is enabled@probe time.
@@ -422,21 +433,11 @@ static void __init h3_init(void)
h3_mmc_init();
}
-static void __init h3_init_smc91x(void)
-{
- omap_cfg_reg(W15_1710_GPIO40);
- if (gpio_request(40, "SMC91x irq") < 0) {
- printk("Error requesting gpio 40 for smc91x irq\n");
- return;
- }
-}
-
static void __init h3_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- h3_init_smc91x();
}
static void __init h3_map_io(void)
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index dc2b86f..0feaa67 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -296,7 +296,6 @@ static void __init innovator_init_irq(void)
omap1510_fpga_init_irq();
}
#endif
- innovator_init_smc91x();
}
#ifdef CONFIG_ARCH_OMAP15XX
@@ -387,6 +386,8 @@ static struct omap_board_config_kernel innovator_config[] = {
static void __init innovator_init(void)
{
+ innovator_init_smc91x();
+
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
unsigned char reg;
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index e9dd791..30bdbdb 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -284,8 +284,6 @@ static void __init osk_init_irq(void)
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- osk_init_smc91x();
- osk_init_cf();
}
static struct omap_usb_config osk_usb_config __initdata = {
@@ -541,6 +539,9 @@ static void __init osk_init(void)
{
u32 l;
+ osk_init_smc91x();
+ osk_init_cf();
+
/* Workaround for wrong CS3 (NOR flash) timing
* There are some U-Boot versions out there which configure
* wrong CS3 memory timings. This mainly leads to CRC
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index a8d16a2..07660be 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -251,8 +251,19 @@ static struct omap_board_config_kernel perseus2_config[] __initdata = {
{ OMAP_TAG_LCD, &perseus2_lcd_config },
};
+static void __init perseus2_init_smc91x(void)
+{
+ fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+ fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
+ H2P2_DBG_FPGA_LAN_RESET);
+ mdelay(50);
+}
+
static void __init omap_perseus2_init(void)
{
+ perseus2_init_smc91x();
+
if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
BUG();
gpio_direction_input(P2_NAND_RB_GPIO_PIN);
@@ -280,21 +291,11 @@ static void __init omap_perseus2_init(void)
omap_register_i2c_bus(1, 100, NULL, 0);
}
-static void __init perseus2_init_smc91x(void)
-{
- fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
- fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
- H2P2_DBG_FPGA_LAN_RESET);
- mdelay(50);
-}
-
static void __init omap_perseus2_init_irq(void)
{
omap1_init_common_hw();
omap_init_irq();
omap_gpio_init();
- perseus2_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 2c6db1a..6ae777e 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -281,7 +281,6 @@ static void __init omap_apollon_init_irq(void)
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
- apollon_init_smc91x();
}
static void __init apollon_led_init(void)
@@ -324,6 +323,7 @@ static void __init omap_apollon_init(void)
omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
+ apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
apollon_usb_init();
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index 001fd97..3dab44e 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -295,7 +295,6 @@ static void __init omap_ldp_init_irq(void)
omap2_init_common_hw(NULL, NULL);
omap_init_irq();
omap_gpio_init();
- ldp_init_smsc911x();
}
static struct twl4030_usb_data ldp_usb_data = {
@@ -426,6 +425,7 @@ static struct mtd_partition ldp_nand_partitions[] = {
static void __init omap_ldp_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+ ldp_init_smsc911x();
omap_i2c_init();
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
ts_gpio = 54;
next prev parent reply other threads:[~2010-12-08 0:55 UTC|newest]
Thread overview: 74+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-11-25 12:48 [PATCH v8 00/11] OMAP: GPIO: Implement GPIO as platform device Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 01/11] OMAP: GPIO: prepare for platform driver Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-12-01 18:34 ` [PATCH v8 01-b/11] OMAP: GPIO: Make omap_gpio_show_rev bank specific Tony Lindgren
2010-12-01 18:34 ` Tony Lindgren
2010-12-09 19:18 ` [PATCH v8 01/11] OMAP: GPIO: prepare for platform driver Kevin Hilman
2010-12-09 19:18 ` Kevin Hilman
2010-12-09 21:33 ` Cousson, Benoit
2010-12-09 21:33 ` Cousson, Benoit
2010-12-09 22:19 ` Kevin Hilman
2010-12-09 22:19 ` Kevin Hilman
2010-12-09 22:29 ` Cousson, Benoit
2010-12-09 22:29 ` Cousson, Benoit
2010-12-09 23:19 ` Kevin Hilman
2010-12-09 23:19 ` Kevin Hilman
2010-11-25 12:48 ` [PATCH v8 02/11] OMAP15xx: GPIO: Introduce support for GPIO init Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 03/11] OMAP16xx: " Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 04/11] OMAP7xx: " Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-12-07 5:20 ` Cory Maccarrone
2010-12-07 5:20 ` Cory Maccarrone
2010-12-07 5:43 ` Varadarajan, Charulatha
2010-12-07 5:43 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 05/11] OMAP2420: hwmod data: Add GPIO Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 06/11] OMAP2430: " Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 07/11] OMAP3: " Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 08/11] OMAP4: " Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 09/11] OMAP2+: GPIO: device registration Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-11-25 12:48 ` [PATCH v8 10/11] OMAP: GPIO: Implement GPIO as a platform device Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-12-07 5:19 ` Cory Maccarrone
2010-12-07 5:19 ` Cory Maccarrone
2010-12-07 5:35 ` Varadarajan, Charulatha
2010-12-07 5:35 ` Varadarajan, Charulatha
2010-12-07 7:08 ` Varadarajan, Charulatha
2010-12-07 7:08 ` Varadarajan, Charulatha
2010-12-07 22:07 ` Tony Lindgren
2010-12-07 22:07 ` Tony Lindgren
2010-11-25 12:48 ` [PATCH v8 11/11] OMAP: GPIO: Remove omap_gpio_init() Varadarajan, Charulatha
2010-11-25 12:48 ` Varadarajan, Charulatha
2010-12-01 18:33 ` [PATCH v8 00/11] OMAP: GPIO: Implement GPIO as platform device Tony Lindgren
2010-12-01 18:33 ` Tony Lindgren
2010-12-02 9:58 ` Kevin Hilman
2010-12-02 9:58 ` Kevin Hilman
2010-12-02 14:18 ` Varadarajan, Charulatha
2010-12-02 14:18 ` Varadarajan, Charulatha
2010-12-04 21:25 ` Tony Lindgren
2010-12-04 21:25 ` Tony Lindgren
2010-12-07 23:23 ` [PATCH 12/11] omap1: Fix gpio mpuio bank to work for multi-omap for 7xx/15xx/16xx Tony Lindgren
2010-12-07 23:23 ` Tony Lindgren
2010-12-08 1:04 ` Tony Lindgren
2010-12-08 1:04 ` Tony Lindgren
2010-12-08 4:22 ` Varadarajan, Charulatha
2010-12-08 4:22 ` Varadarajan, Charulatha
2010-12-10 16:04 ` Janusz Krzysztofik
2010-12-10 16:04 ` Janusz Krzysztofik
2010-12-10 17:41 ` Tony Lindgren
2010-12-10 17:41 ` Tony Lindgren
2010-12-08 0:54 ` Tony Lindgren [this message]
2010-12-08 0:54 ` [PATCH v8 00/11] OMAP: GPIO: Implement GPIO as platform device Tony Lindgren
2010-12-09 19:33 ` [PATCH 13/11] OMAP2+: GPIO: ensure bank wakeups are enabled by default Kevin Hilman
2010-12-09 19:33 ` Kevin Hilman
2010-12-10 0:07 ` Tony Lindgren
2010-12-10 0:07 ` Tony Lindgren
2010-12-10 0:14 ` Kevin Hilman
2010-12-10 0:14 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20101208005452.GG17435@atomide.com \
--to=tony@atomide.com \
--cc=b-cousson@ti.com \
--cc=charu@ti.com \
--cc=darkstar6262@gmail.com \
--cc=jkrzyszt@tis.icnet.pl \
--cc=khilman@deeprootsystems.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=p-basak2@ti.com \
--cc=paul@pwsan.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.