From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
To: linux-renesas-soc@vger.kernel.org
Cc: linux-sh@vger.kernel.org, linux-serial@vger.kernel.org,
Geert Uytterhoeven <geert+renesas@glider.be>
Subject: [PATCH 07/19] sh: Don't set sh-sci port_reg
Date: Tue, 03 Jan 2017 23:06:27 +0000 [thread overview]
Message-ID: <20170103230639.19660-8-laurent.pinchart+renesas@ideasonboard.com> (raw)
In-Reply-To: <20170103230639.19660-1-laurent.pinchart+renesas@ideasonboard.com>
The driver considers all negative or zero values of the port_reg field
as invalid. The four platforms that set the field to a register address
all use an address higher than 0x7fffffff, which is thus considered by
the driver as invalid. The feature is thus never used, remove it.
The feature could be implemented properly in the future using the
pinctrl and GPIO APIs if desired.
While at it, don't set the field to SCIx_NOT_SUPPORTED (-1) either,
leaving it unset leads to the same result. This will allow removing the
SCIx_NOT_SUPPORTED macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
arch/sh/kernel/cpu/sh3/setup-sh770x.c | 2 --
arch/sh/kernel/cpu/sh4/setup-sh7750.c | 1 -
arch/sh/kernel/cpu/sh4a/setup-sh7366.c | 1 -
arch/sh/kernel/cpu/sh4a/setup-sh7723.c | 6 ------
arch/sh/kernel/cpu/sh4a/setup-sh7724.c | 6 ------
5 files changed, 16 deletions(-)
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh770x.c b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
index e64fe24d860c..e1e54258b822 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh770x.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
@@ -109,7 +109,6 @@ static struct platform_device rtc_device = {
};
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa4000136,
.type = PORT_SCI,
.ops = &sh770x_sci_port_ops,
.regshift = 1,
@@ -156,7 +155,6 @@ static struct platform_device scif1_device = {
#if defined(CONFIG_CPU_SUBTYPE_SH7707) || \
defined(CONFIG_CPU_SUBTYPE_SH7709)
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.type = PORT_IRDA,
.ops = &sh770x_sci_port_ops,
.regshift = 1,
diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7750.c b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
index f693f122a286..d98a55416306 100644
--- a/arch/sh/kernel/cpu/sh4/setup-sh7750.c
+++ b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
@@ -38,7 +38,6 @@ static struct platform_device rtc_device = {
};
static struct plat_sci_port sci_platform_data = {
- .port_reg = 0xffe0001C,
.type = PORT_SCI,
.regshift = 2,
};
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
index 3fc1a3ab634e..646918713d9a 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
@@ -20,7 +20,6 @@
#include <asm/clock.h>
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa405013e,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
};
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
index 9f47ec950af8..6c5cb234aa33 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
@@ -23,7 +23,6 @@
/* Serial */
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa4050160,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -45,7 +44,6 @@ static struct platform_device scif0_device = {
};
static struct plat_sci_port scif1_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -67,7 +65,6 @@ static struct platform_device scif1_device = {
};
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -89,7 +86,6 @@ static struct platform_device scif2_device = {
};
static struct plat_sci_port scif3_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
@@ -111,7 +107,6 @@ static struct platform_device scif3_device = {
};
static struct plat_sci_port scif4_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
@@ -133,7 +128,6 @@ static struct platform_device scif4_device = {
};
static struct plat_sci_port scif5_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
index 3ce55884c787..c20258b18775 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
@@ -290,7 +290,6 @@ static struct platform_device dma1_device = {
/* Serial */
static struct plat_sci_port scif0_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -312,7 +311,6 @@ static struct platform_device scif0_device = {
};
static struct plat_sci_port scif1_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -334,7 +332,6 @@ static struct platform_device scif1_device = {
};
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -356,7 +353,6 @@ static struct platform_device scif2_device = {
};
static struct plat_sci_port scif3_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
@@ -377,7 +373,6 @@ static struct platform_device scif3_device = {
};
static struct plat_sci_port scif4_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
@@ -398,7 +393,6 @@ static struct platform_device scif4_device = {
};
static struct plat_sci_port scif5_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
--
Regards,
Laurent Pinchart
WARNING: multiple messages have this Message-ID (diff)
From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
To: linux-renesas-soc@vger.kernel.org
Cc: linux-sh@vger.kernel.org, linux-serial@vger.kernel.org,
Geert Uytterhoeven <geert+renesas@glider.be>
Subject: [PATCH 07/19] sh: Don't set sh-sci port_reg
Date: Wed, 4 Jan 2017 01:06:27 +0200 [thread overview]
Message-ID: <20170103230639.19660-8-laurent.pinchart+renesas@ideasonboard.com> (raw)
In-Reply-To: <20170103230639.19660-1-laurent.pinchart+renesas@ideasonboard.com>
The driver considers all negative or zero values of the port_reg field
as invalid. The four platforms that set the field to a register address
all use an address higher than 0x7fffffff, which is thus considered by
the driver as invalid. The feature is thus never used, remove it.
The feature could be implemented properly in the future using the
pinctrl and GPIO APIs if desired.
While at it, don't set the field to SCIx_NOT_SUPPORTED (-1) either,
leaving it unset leads to the same result. This will allow removing the
SCIx_NOT_SUPPORTED macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
arch/sh/kernel/cpu/sh3/setup-sh770x.c | 2 --
arch/sh/kernel/cpu/sh4/setup-sh7750.c | 1 -
arch/sh/kernel/cpu/sh4a/setup-sh7366.c | 1 -
arch/sh/kernel/cpu/sh4a/setup-sh7723.c | 6 ------
arch/sh/kernel/cpu/sh4a/setup-sh7724.c | 6 ------
5 files changed, 16 deletions(-)
diff --git a/arch/sh/kernel/cpu/sh3/setup-sh770x.c b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
index e64fe24d860c..e1e54258b822 100644
--- a/arch/sh/kernel/cpu/sh3/setup-sh770x.c
+++ b/arch/sh/kernel/cpu/sh3/setup-sh770x.c
@@ -109,7 +109,6 @@ static struct platform_device rtc_device = {
};
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa4000136,
.type = PORT_SCI,
.ops = &sh770x_sci_port_ops,
.regshift = 1,
@@ -156,7 +155,6 @@ static struct platform_device scif1_device = {
#if defined(CONFIG_CPU_SUBTYPE_SH7707) || \
defined(CONFIG_CPU_SUBTYPE_SH7709)
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.type = PORT_IRDA,
.ops = &sh770x_sci_port_ops,
.regshift = 1,
diff --git a/arch/sh/kernel/cpu/sh4/setup-sh7750.c b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
index f693f122a286..d98a55416306 100644
--- a/arch/sh/kernel/cpu/sh4/setup-sh7750.c
+++ b/arch/sh/kernel/cpu/sh4/setup-sh7750.c
@@ -38,7 +38,6 @@ static struct platform_device rtc_device = {
};
static struct plat_sci_port sci_platform_data = {
- .port_reg = 0xffe0001C,
.type = PORT_SCI,
.regshift = 2,
};
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
index 3fc1a3ab634e..646918713d9a 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7366.c
@@ -20,7 +20,6 @@
#include <asm/clock.h>
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa405013e,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
};
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
index 9f47ec950af8..6c5cb234aa33 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7723.c
@@ -23,7 +23,6 @@
/* Serial */
static struct plat_sci_port scif0_platform_data = {
- .port_reg = 0xa4050160,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -45,7 +44,6 @@ static struct platform_device scif0_device = {
};
static struct plat_sci_port scif1_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -67,7 +65,6 @@ static struct platform_device scif1_device = {
};
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -89,7 +86,6 @@ static struct platform_device scif2_device = {
};
static struct plat_sci_port scif3_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
@@ -111,7 +107,6 @@ static struct platform_device scif3_device = {
};
static struct plat_sci_port scif4_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
@@ -133,7 +128,6 @@ static struct platform_device scif4_device = {
};
static struct plat_sci_port scif5_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.sampling_rate = 8,
.type = PORT_SCIFA,
diff --git a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
index 3ce55884c787..c20258b18775 100644
--- a/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
+++ b/arch/sh/kernel/cpu/sh4a/setup-sh7724.c
@@ -290,7 +290,6 @@ static struct platform_device dma1_device = {
/* Serial */
static struct plat_sci_port scif0_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -312,7 +311,6 @@ static struct platform_device scif0_device = {
};
static struct plat_sci_port scif1_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -334,7 +332,6 @@ static struct platform_device scif1_device = {
};
static struct plat_sci_port scif2_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.scscr = SCSCR_REIE,
.type = PORT_SCIF,
.regtype = SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE,
@@ -356,7 +353,6 @@ static struct platform_device scif2_device = {
};
static struct plat_sci_port scif3_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
@@ -377,7 +373,6 @@ static struct platform_device scif3_device = {
};
static struct plat_sci_port scif4_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
@@ -398,7 +393,6 @@ static struct platform_device scif4_device = {
};
static struct plat_sci_port scif5_platform_data = {
- .port_reg = SCIx_NOT_SUPPORTED,
.sampling_rate = 8,
.type = PORT_SCIFA,
};
--
Regards,
Laurent Pinchart
next prev parent reply other threads:[~2017-01-03 23:06 UTC|newest]
Thread overview: 104+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-03 23:06 [PATCH 00/19] sh-sci: Platform data simplification Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-03 23:06 ` [PATCH 01/19] serial: sh-sci: Set the SCSCR TE and RE bits in the driver Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 02/19] serial: sh-sci: Don't rely on platform data flags when not needed Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 03/19] sh: Don't set sh-sci pdata scscr TE and RE bits Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 04/19] sh: Don't set sh-sci pdata scscr TIE and RIE bits Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-06 10:11 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 05/19] sh: sh726[49]: Don't set sh-sci pdata scscr TOIE bit Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:13 ` Geert Uytterhoeven
2017-01-06 10:13 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 06/19] sh: Don't set the sh-sci pdata UPF_BOOT_AUTOCONF flags Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:13 ` Geert Uytterhoeven
2017-01-06 10:13 ` Geert Uytterhoeven
2017-01-03 23:06 ` Laurent Pinchart [this message]
2017-01-03 23:06 ` [PATCH 07/19] sh: Don't set sh-sci port_reg Laurent Pinchart
2017-01-06 10:17 ` Geert Uytterhoeven
2017-01-06 10:17 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 08/19] sh: sh3: sh770x: Fix platform data for the IRDA serial port Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:18 ` Geert Uytterhoeven
2017-01-06 10:18 ` Geert Uytterhoeven
2017-01-06 10:25 ` Laurent Pinchart
2017-01-06 10:25 ` Laurent Pinchart
2017-01-06 11:52 ` [PATCH v1.1 08/19] serial: sh-sci: Fix register offsets " Laurent Pinchart
2017-01-06 11:52 ` Laurent Pinchart
2017-01-11 12:31 ` Geert Uytterhoeven
2017-01-11 12:31 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 09/19] sh: Don't set the sh-sci platform data regshift field Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:18 ` Geert Uytterhoeven
2017-01-06 10:18 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 10/19] sh: Don't set the sh-sci platform data scscr CKE0 bit Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:23 ` Geert Uytterhoeven
2017-01-06 10:23 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 11/19] sh: Don't set the sh-sci platform data REIE bit when not implemented Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:27 ` Geert Uytterhoeven
2017-01-06 10:27 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 12/19] serial: sh-sci: Remove initialization of zero fields in sci_port_params Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:29 ` Geert Uytterhoeven
2017-01-06 10:29 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 13/19] serial: sh-sci: Replace regmap array with port parameters Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:36 ` Geert Uytterhoeven
2017-01-06 10:36 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 14/19] serial: sh-sci: Constify platform data Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:36 ` Geert Uytterhoeven
2017-01-06 10:36 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 15/19] serial: sh-sci: Extend sci_port_params with more port parameters Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:51 ` Geert Uytterhoeven
2017-01-06 10:51 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 16/19] serial: sh-sci: Remove the platform data dma slave rx/tx channel IDs Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:53 ` Geert Uytterhoeven
2017-01-06 10:53 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 17/19] serial: sh-sci: Remove manual break debouncing Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:57 ` Geert Uytterhoeven
2017-01-06 10:57 ` Geert Uytterhoeven
2017-01-03 23:06 ` [PATCH 18/19] serial: sh-sci: Remove unused platform data capabilities field Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 10:59 ` Geert Uytterhoeven
2017-01-06 10:59 ` Geert Uytterhoeven
2017-01-06 11:05 ` Laurent Pinchart
2017-01-06 11:05 ` Laurent Pinchart
2017-01-03 23:06 ` [PATCH 19/19] serial: sh-sci: Compute the regshift value for SCI ports Laurent Pinchart
2017-01-03 23:06 ` Laurent Pinchart
2017-01-06 11:00 ` Geert Uytterhoeven
2017-01-06 11:00 ` Geert Uytterhoeven
2017-01-06 12:21 ` [PATCH v1.1 " Laurent Pinchart
2017-01-06 12:21 ` Laurent Pinchart
2017-01-11 12:37 ` Geert Uytterhoeven
2017-01-11 12:37 ` Geert Uytterhoeven
2017-01-06 11:01 ` [PATCH 00/19] sh-sci: Platform data simplification Geert Uytterhoeven
2017-01-06 11:01 ` Geert Uytterhoeven
2017-01-11 8:04 ` Greg KH
2017-01-11 8:04 ` Greg KH
2017-01-11 10:38 ` Geert Uytterhoeven
2017-01-11 10:38 ` Geert Uytterhoeven
2017-01-11 10:43 ` Greg KH
2017-01-11 10:43 ` Greg KH
2017-01-11 11:06 ` Laurent Pinchart
2017-01-11 11:06 ` Laurent Pinchart
2017-01-11 20:31 ` Greg KH
2017-01-11 20:31 ` Greg KH
2017-01-11 11:03 ` Laurent Pinchart
2017-01-11 11:03 ` Laurent Pinchart
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170103230639.19660-8-laurent.pinchart+renesas@ideasonboard.com \
--to=laurent.pinchart+renesas@ideasonboard.com \
--cc=geert+renesas@glider.be \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.