From: Lee Jones <lee.jones@linaro.org>
To: Icenowy Zheng <icenowy@aosc.io>
Cc: Rob Herring <robh+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
Maxime Ripard <maxime.ripard@free-electrons.com>,
Liam Girdwood <lgirdwood@gmail.com>,
devicetree@vger.kernel.org, linux-sunxi@googlegroups.com,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v2 04/11] mfd: axp20x: support AXP803 variant
Date: Tue, 11 Apr 2017 15:04:12 +0100 [thread overview]
Message-ID: <20170411140412.b2ncflm2iluuuai5@dell> (raw)
In-Reply-To: <20170407183441.58750-5-icenowy@aosc.io>
On Sat, 08 Apr 2017, Icenowy Zheng wrote:
> AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
> via RSB bus. The PMIC itself is like AXP288, but with RSB support and
> dedicated VBUS and ACIN.
>
> Add support for it in the axp20x mfd driver.
>
> Currently only power key function is supported.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v2:
> - Share regmap configs with AXP288.
> - Place AXP803 bits before AXP806/809.
>
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 79 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 40 ++++++++++++++++++++++-
> 3 files changed, 119 insertions(+), 1 deletion(-)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a732cb50bcff..fd5c7267b136 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
> { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 5ba3b04cc9b1..2268a6a9aa2c 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -41,6 +41,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP803",
> "AXP806",
> "AXP809",
> };
> @@ -117,6 +118,7 @@ static const struct regmap_access_table axp22x_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp22x_volatile_ranges),
> };
>
> +/* AXP288 ranges are shared with the AXP803, as they cover the same range */
> static const struct regmap_range axp288_writeable_ranges[] = {
> regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ6_STATE),
> regmap_reg_range(AXP20X_DCDC_MODE, AXP288_FG_TUNE5),
> @@ -264,6 +266,20 @@ static struct resource axp288_fuel_gauge_resources[] = {
> },
> };
>
> +static struct resource axp803_pek_resources[] = {
> + {
> + .name = "PEK_DBR",
> + .start = AXP803_IRQ_PEK_RIS_EDGE,
> + .end = AXP803_IRQ_PEK_RIS_EDGE,
> + .flags = IORESOURCE_IRQ,
> + }, {
> + .name = "PEK_DBF",
> + .start = AXP803_IRQ_PEK_FAL_EDGE,
> + .end = AXP803_IRQ_PEK_FAL_EDGE,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> static struct resource axp809_pek_resources[] = {
> {
> .name = "PEK_DBR",
> @@ -457,6 +473,43 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp803_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP803, ACIN_OVER_V, 0, 7),
> + INIT_REGMAP_IRQ(AXP803, ACIN_PLUGIN, 0, 6),
> + INIT_REGMAP_IRQ(AXP803, ACIN_REMOVAL, 0, 5),
> + INIT_REGMAP_IRQ(AXP803, VBUS_OVER_V, 0, 4),
> + INIT_REGMAP_IRQ(AXP803, VBUS_PLUGIN, 0, 3),
> + INIT_REGMAP_IRQ(AXP803, VBUS_REMOVAL, 0, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_PLUGIN, 1, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_REMOVAL, 1, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_ENT_ACT_MODE, 1, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_EXIT_ACT_MODE, 1, 4),
> + INIT_REGMAP_IRQ(AXP803, CHARG, 1, 3),
> + INIT_REGMAP_IRQ(AXP803, CHARG_DONE, 1, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH, 2, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH_END, 2, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW, 2, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW_END, 2, 4),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH, 2, 3),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH_END, 2, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW, 2, 1),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW_END, 2, 0),
> + INIT_REGMAP_IRQ(AXP803, DIE_TEMP_HIGH, 3, 7),
> + INIT_REGMAP_IRQ(AXP803, GPADC, 3, 2),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL1, 3, 1),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL2, 3, 0),
> + INIT_REGMAP_IRQ(AXP803, TIMER, 4, 7),
> + INIT_REGMAP_IRQ(AXP803, PEK_RIS_EDGE, 4, 6),
> + INIT_REGMAP_IRQ(AXP803, PEK_FAL_EDGE, 4, 5),
> + INIT_REGMAP_IRQ(AXP803, PEK_SHORT, 4, 4),
> + INIT_REGMAP_IRQ(AXP803, PEK_LONG, 4, 3),
> + INIT_REGMAP_IRQ(AXP803, PEK_OVER_OFF, 4, 2),
> + INIT_REGMAP_IRQ(AXP803, GPIO1_INPUT, 4, 1),
> + INIT_REGMAP_IRQ(AXP803, GPIO0_INPUT, 4, 0),
> + INIT_REGMAP_IRQ(AXP803, BC_USB_CHNG, 5, 1),
> + INIT_REGMAP_IRQ(AXP803, MV_CHNG, 5, 0),
> +};
> +
> static const struct regmap_irq axp806_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> @@ -557,6 +610,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp803_regmap_irq_chip = {
> + .name = "axp803",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp803_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp803_regmap_irqs),
> + .num_regs = 6,
> +};
> +
> static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> .name = "axp806",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -769,6 +834,14 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp803_cells[] = {
> + {
> + .name = "axp20x-pek",
> + .num_resources = ARRAY_SIZE(axp803_pek_resources),
> + .resources = axp803_pek_resources,
> + }
> +};
> +
> static struct mfd_cell axp806_cells[] = {
> {
> .id = 2,
> @@ -855,6 +928,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> axp20x->irq_flags = IRQF_TRIGGER_LOW;
> break;
> + case AXP803_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp803_cells);
> + axp20x->cells = axp803_cells;
> + axp20x->regmap_cfg = &axp288_regmap_config;
> + axp20x->regmap_irq_chip = &axp803_regmap_irq_chip;
> + break;
> case AXP806_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> axp20x->cells = axp806_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index dc8798cf2a24..cde56cfe8446 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum axp20x_variants {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP803_ID,
> AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> @@ -234,7 +235,7 @@ enum axp20x_variants {
> #define AXP22X_TS_ADC_L 0x59
> #define AXP22X_BATLOW_THRES1 0xe6
>
> -/* AXP288 specific registers */
> +/* AXP288/AXP803 specific registers */
> #define AXP288_POWER_REASON 0x02
> #define AXP288_BC_GLOBAL 0x2c
> #define AXP288_BC_VBUS_CNTL 0x2d
> @@ -475,6 +476,43 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp803_irqs {
> + AXP803_IRQ_ACIN_OVER_V = 1,
> + AXP803_IRQ_ACIN_PLUGIN,
> + AXP803_IRQ_ACIN_REMOVAL,
> + AXP803_IRQ_VBUS_OVER_V,
> + AXP803_IRQ_VBUS_PLUGIN,
> + AXP803_IRQ_VBUS_REMOVAL,
> + AXP803_IRQ_BATT_PLUGIN,
> + AXP803_IRQ_BATT_REMOVAL,
> + AXP803_IRQ_BATT_ENT_ACT_MODE,
> + AXP803_IRQ_BATT_EXIT_ACT_MODE,
> + AXP803_IRQ_CHARG,
> + AXP803_IRQ_CHARG_DONE,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW_END,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW_END,
> + AXP803_IRQ_DIE_TEMP_HIGH,
> + AXP803_IRQ_GPADC,
> + AXP803_IRQ_LOW_PWR_LVL1,
> + AXP803_IRQ_LOW_PWR_LVL2,
> + AXP803_IRQ_TIMER,
> + AXP803_IRQ_PEK_RIS_EDGE,
> + AXP803_IRQ_PEK_FAL_EDGE,
> + AXP803_IRQ_PEK_SHORT,
> + AXP803_IRQ_PEK_LONG,
> + AXP803_IRQ_PEK_OVER_OFF,
> + AXP803_IRQ_GPIO1_INPUT,
> + AXP803_IRQ_GPIO0_INPUT,
> + AXP803_IRQ_BC_USB_CHNG,
> + AXP803_IRQ_MV_CHNG,
> +};
> +
> enum axp806_irqs {
> AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> AXP806_IRQ_DIE_TEMP_HIGH_LV2,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
WARNING: multiple messages have this Message-ID (diff)
From: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
To: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
Cc: Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>,
Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>,
Liam Girdwood <lgirdwood-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: Re: [PATCH v2 04/11] mfd: axp20x: support AXP803 variant
Date: Tue, 11 Apr 2017 15:04:12 +0100 [thread overview]
Message-ID: <20170411140412.b2ncflm2iluuuai5@dell> (raw)
In-Reply-To: <20170407183441.58750-5-icenowy-h8G6r0blFSE@public.gmane.org>
On Sat, 08 Apr 2017, Icenowy Zheng wrote:
> AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
> via RSB bus. The PMIC itself is like AXP288, but with RSB support and
> dedicated VBUS and ACIN.
>
> Add support for it in the axp20x mfd driver.
>
> Currently only power key function is supported.
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> ---
> Changes in v2:
> - Share regmap configs with AXP288.
> - Place AXP803 bits before AXP806/809.
>
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 79 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 40 ++++++++++++++++++++++-
> 3 files changed, 119 insertions(+), 1 deletion(-)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a732cb50bcff..fd5c7267b136 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
> { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 5ba3b04cc9b1..2268a6a9aa2c 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -41,6 +41,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP803",
> "AXP806",
> "AXP809",
> };
> @@ -117,6 +118,7 @@ static const struct regmap_access_table axp22x_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp22x_volatile_ranges),
> };
>
> +/* AXP288 ranges are shared with the AXP803, as they cover the same range */
> static const struct regmap_range axp288_writeable_ranges[] = {
> regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ6_STATE),
> regmap_reg_range(AXP20X_DCDC_MODE, AXP288_FG_TUNE5),
> @@ -264,6 +266,20 @@ static struct resource axp288_fuel_gauge_resources[] = {
> },
> };
>
> +static struct resource axp803_pek_resources[] = {
> + {
> + .name = "PEK_DBR",
> + .start = AXP803_IRQ_PEK_RIS_EDGE,
> + .end = AXP803_IRQ_PEK_RIS_EDGE,
> + .flags = IORESOURCE_IRQ,
> + }, {
> + .name = "PEK_DBF",
> + .start = AXP803_IRQ_PEK_FAL_EDGE,
> + .end = AXP803_IRQ_PEK_FAL_EDGE,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> static struct resource axp809_pek_resources[] = {
> {
> .name = "PEK_DBR",
> @@ -457,6 +473,43 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp803_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP803, ACIN_OVER_V, 0, 7),
> + INIT_REGMAP_IRQ(AXP803, ACIN_PLUGIN, 0, 6),
> + INIT_REGMAP_IRQ(AXP803, ACIN_REMOVAL, 0, 5),
> + INIT_REGMAP_IRQ(AXP803, VBUS_OVER_V, 0, 4),
> + INIT_REGMAP_IRQ(AXP803, VBUS_PLUGIN, 0, 3),
> + INIT_REGMAP_IRQ(AXP803, VBUS_REMOVAL, 0, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_PLUGIN, 1, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_REMOVAL, 1, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_ENT_ACT_MODE, 1, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_EXIT_ACT_MODE, 1, 4),
> + INIT_REGMAP_IRQ(AXP803, CHARG, 1, 3),
> + INIT_REGMAP_IRQ(AXP803, CHARG_DONE, 1, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH, 2, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH_END, 2, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW, 2, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW_END, 2, 4),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH, 2, 3),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH_END, 2, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW, 2, 1),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW_END, 2, 0),
> + INIT_REGMAP_IRQ(AXP803, DIE_TEMP_HIGH, 3, 7),
> + INIT_REGMAP_IRQ(AXP803, GPADC, 3, 2),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL1, 3, 1),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL2, 3, 0),
> + INIT_REGMAP_IRQ(AXP803, TIMER, 4, 7),
> + INIT_REGMAP_IRQ(AXP803, PEK_RIS_EDGE, 4, 6),
> + INIT_REGMAP_IRQ(AXP803, PEK_FAL_EDGE, 4, 5),
> + INIT_REGMAP_IRQ(AXP803, PEK_SHORT, 4, 4),
> + INIT_REGMAP_IRQ(AXP803, PEK_LONG, 4, 3),
> + INIT_REGMAP_IRQ(AXP803, PEK_OVER_OFF, 4, 2),
> + INIT_REGMAP_IRQ(AXP803, GPIO1_INPUT, 4, 1),
> + INIT_REGMAP_IRQ(AXP803, GPIO0_INPUT, 4, 0),
> + INIT_REGMAP_IRQ(AXP803, BC_USB_CHNG, 5, 1),
> + INIT_REGMAP_IRQ(AXP803, MV_CHNG, 5, 0),
> +};
> +
> static const struct regmap_irq axp806_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> @@ -557,6 +610,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp803_regmap_irq_chip = {
> + .name = "axp803",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp803_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp803_regmap_irqs),
> + .num_regs = 6,
> +};
> +
> static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> .name = "axp806",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -769,6 +834,14 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp803_cells[] = {
> + {
> + .name = "axp20x-pek",
> + .num_resources = ARRAY_SIZE(axp803_pek_resources),
> + .resources = axp803_pek_resources,
> + }
> +};
> +
> static struct mfd_cell axp806_cells[] = {
> {
> .id = 2,
> @@ -855,6 +928,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> axp20x->irq_flags = IRQF_TRIGGER_LOW;
> break;
> + case AXP803_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp803_cells);
> + axp20x->cells = axp803_cells;
> + axp20x->regmap_cfg = &axp288_regmap_config;
> + axp20x->regmap_irq_chip = &axp803_regmap_irq_chip;
> + break;
> case AXP806_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> axp20x->cells = axp806_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index dc8798cf2a24..cde56cfe8446 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum axp20x_variants {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP803_ID,
> AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> @@ -234,7 +235,7 @@ enum axp20x_variants {
> #define AXP22X_TS_ADC_L 0x59
> #define AXP22X_BATLOW_THRES1 0xe6
>
> -/* AXP288 specific registers */
> +/* AXP288/AXP803 specific registers */
> #define AXP288_POWER_REASON 0x02
> #define AXP288_BC_GLOBAL 0x2c
> #define AXP288_BC_VBUS_CNTL 0x2d
> @@ -475,6 +476,43 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp803_irqs {
> + AXP803_IRQ_ACIN_OVER_V = 1,
> + AXP803_IRQ_ACIN_PLUGIN,
> + AXP803_IRQ_ACIN_REMOVAL,
> + AXP803_IRQ_VBUS_OVER_V,
> + AXP803_IRQ_VBUS_PLUGIN,
> + AXP803_IRQ_VBUS_REMOVAL,
> + AXP803_IRQ_BATT_PLUGIN,
> + AXP803_IRQ_BATT_REMOVAL,
> + AXP803_IRQ_BATT_ENT_ACT_MODE,
> + AXP803_IRQ_BATT_EXIT_ACT_MODE,
> + AXP803_IRQ_CHARG,
> + AXP803_IRQ_CHARG_DONE,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW_END,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW_END,
> + AXP803_IRQ_DIE_TEMP_HIGH,
> + AXP803_IRQ_GPADC,
> + AXP803_IRQ_LOW_PWR_LVL1,
> + AXP803_IRQ_LOW_PWR_LVL2,
> + AXP803_IRQ_TIMER,
> + AXP803_IRQ_PEK_RIS_EDGE,
> + AXP803_IRQ_PEK_FAL_EDGE,
> + AXP803_IRQ_PEK_SHORT,
> + AXP803_IRQ_PEK_LONG,
> + AXP803_IRQ_PEK_OVER_OFF,
> + AXP803_IRQ_GPIO1_INPUT,
> + AXP803_IRQ_GPIO0_INPUT,
> + AXP803_IRQ_BC_USB_CHNG,
> + AXP803_IRQ_MV_CHNG,
> +};
> +
> enum axp806_irqs {
> AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> AXP806_IRQ_DIE_TEMP_HIGH_LV2,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
WARNING: multiple messages have this Message-ID (diff)
From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 04/11] mfd: axp20x: support AXP803 variant
Date: Tue, 11 Apr 2017 15:04:12 +0100 [thread overview]
Message-ID: <20170411140412.b2ncflm2iluuuai5@dell> (raw)
In-Reply-To: <20170407183441.58750-5-icenowy@aosc.io>
On Sat, 08 Apr 2017, Icenowy Zheng wrote:
> AXP803 is a new PMIC chip produced by X-Powers, usually paired with A64
> via RSB bus. The PMIC itself is like AXP288, but with RSB support and
> dedicated VBUS and ACIN.
>
> Add support for it in the axp20x mfd driver.
>
> Currently only power key function is supported.
>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
> ---
> Changes in v2:
> - Share regmap configs with AXP288.
> - Place AXP803 bits before AXP806/809.
>
> drivers/mfd/axp20x-rsb.c | 1 +
> drivers/mfd/axp20x.c | 79 ++++++++++++++++++++++++++++++++++++++++++++++
> include/linux/mfd/axp20x.h | 40 ++++++++++++++++++++++-
> 3 files changed, 119 insertions(+), 1 deletion(-)
Applied, thanks.
> diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
> index a732cb50bcff..fd5c7267b136 100644
> --- a/drivers/mfd/axp20x-rsb.c
> +++ b/drivers/mfd/axp20x-rsb.c
> @@ -61,6 +61,7 @@ static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
>
> static const struct of_device_id axp20x_rsb_of_match[] = {
> { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
> + { .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
> { .compatible = "x-powers,axp806", .data = (void *)AXP806_ID },
> { .compatible = "x-powers,axp809", .data = (void *)AXP809_ID },
> { },
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index 5ba3b04cc9b1..2268a6a9aa2c 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -41,6 +41,7 @@ static const char * const axp20x_model_names[] = {
> "AXP221",
> "AXP223",
> "AXP288",
> + "AXP803",
> "AXP806",
> "AXP809",
> };
> @@ -117,6 +118,7 @@ static const struct regmap_access_table axp22x_volatile_table = {
> .n_yes_ranges = ARRAY_SIZE(axp22x_volatile_ranges),
> };
>
> +/* AXP288 ranges are shared with the AXP803, as they cover the same range */
> static const struct regmap_range axp288_writeable_ranges[] = {
> regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ6_STATE),
> regmap_reg_range(AXP20X_DCDC_MODE, AXP288_FG_TUNE5),
> @@ -264,6 +266,20 @@ static struct resource axp288_fuel_gauge_resources[] = {
> },
> };
>
> +static struct resource axp803_pek_resources[] = {
> + {
> + .name = "PEK_DBR",
> + .start = AXP803_IRQ_PEK_RIS_EDGE,
> + .end = AXP803_IRQ_PEK_RIS_EDGE,
> + .flags = IORESOURCE_IRQ,
> + }, {
> + .name = "PEK_DBF",
> + .start = AXP803_IRQ_PEK_FAL_EDGE,
> + .end = AXP803_IRQ_PEK_FAL_EDGE,
> + .flags = IORESOURCE_IRQ,
> + },
> +};
> +
> static struct resource axp809_pek_resources[] = {
> {
> .name = "PEK_DBR",
> @@ -457,6 +473,43 @@ static const struct regmap_irq axp288_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
> };
>
> +static const struct regmap_irq axp803_regmap_irqs[] = {
> + INIT_REGMAP_IRQ(AXP803, ACIN_OVER_V, 0, 7),
> + INIT_REGMAP_IRQ(AXP803, ACIN_PLUGIN, 0, 6),
> + INIT_REGMAP_IRQ(AXP803, ACIN_REMOVAL, 0, 5),
> + INIT_REGMAP_IRQ(AXP803, VBUS_OVER_V, 0, 4),
> + INIT_REGMAP_IRQ(AXP803, VBUS_PLUGIN, 0, 3),
> + INIT_REGMAP_IRQ(AXP803, VBUS_REMOVAL, 0, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_PLUGIN, 1, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_REMOVAL, 1, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_ENT_ACT_MODE, 1, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_EXIT_ACT_MODE, 1, 4),
> + INIT_REGMAP_IRQ(AXP803, CHARG, 1, 3),
> + INIT_REGMAP_IRQ(AXP803, CHARG_DONE, 1, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH, 2, 7),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_HIGH_END, 2, 6),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW, 2, 5),
> + INIT_REGMAP_IRQ(AXP803, BATT_CHG_TEMP_LOW_END, 2, 4),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH, 2, 3),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_HIGH_END, 2, 2),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW, 2, 1),
> + INIT_REGMAP_IRQ(AXP803, BATT_ACT_TEMP_LOW_END, 2, 0),
> + INIT_REGMAP_IRQ(AXP803, DIE_TEMP_HIGH, 3, 7),
> + INIT_REGMAP_IRQ(AXP803, GPADC, 3, 2),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL1, 3, 1),
> + INIT_REGMAP_IRQ(AXP803, LOW_PWR_LVL2, 3, 0),
> + INIT_REGMAP_IRQ(AXP803, TIMER, 4, 7),
> + INIT_REGMAP_IRQ(AXP803, PEK_RIS_EDGE, 4, 6),
> + INIT_REGMAP_IRQ(AXP803, PEK_FAL_EDGE, 4, 5),
> + INIT_REGMAP_IRQ(AXP803, PEK_SHORT, 4, 4),
> + INIT_REGMAP_IRQ(AXP803, PEK_LONG, 4, 3),
> + INIT_REGMAP_IRQ(AXP803, PEK_OVER_OFF, 4, 2),
> + INIT_REGMAP_IRQ(AXP803, GPIO1_INPUT, 4, 1),
> + INIT_REGMAP_IRQ(AXP803, GPIO0_INPUT, 4, 0),
> + INIT_REGMAP_IRQ(AXP803, BC_USB_CHNG, 5, 1),
> + INIT_REGMAP_IRQ(AXP803, MV_CHNG, 5, 0),
> +};
> +
> static const struct regmap_irq axp806_regmap_irqs[] = {
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV1, 0, 0),
> INIT_REGMAP_IRQ(AXP806, DIE_TEMP_HIGH_LV2, 0, 1),
> @@ -557,6 +610,18 @@ static const struct regmap_irq_chip axp288_regmap_irq_chip = {
>
> };
>
> +static const struct regmap_irq_chip axp803_regmap_irq_chip = {
> + .name = "axp803",
> + .status_base = AXP20X_IRQ1_STATE,
> + .ack_base = AXP20X_IRQ1_STATE,
> + .mask_base = AXP20X_IRQ1_EN,
> + .mask_invert = true,
> + .init_ack_masked = true,
> + .irqs = axp803_regmap_irqs,
> + .num_irqs = ARRAY_SIZE(axp803_regmap_irqs),
> + .num_regs = 6,
> +};
> +
> static const struct regmap_irq_chip axp806_regmap_irq_chip = {
> .name = "axp806",
> .status_base = AXP20X_IRQ1_STATE,
> @@ -769,6 +834,14 @@ static struct mfd_cell axp288_cells[] = {
> },
> };
>
> +static struct mfd_cell axp803_cells[] = {
> + {
> + .name = "axp20x-pek",
> + .num_resources = ARRAY_SIZE(axp803_pek_resources),
> + .resources = axp803_pek_resources,
> + }
> +};
> +
> static struct mfd_cell axp806_cells[] = {
> {
> .id = 2,
> @@ -855,6 +928,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
> axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
> axp20x->irq_flags = IRQF_TRIGGER_LOW;
> break;
> + case AXP803_ID:
> + axp20x->nr_cells = ARRAY_SIZE(axp803_cells);
> + axp20x->cells = axp803_cells;
> + axp20x->regmap_cfg = &axp288_regmap_config;
> + axp20x->regmap_irq_chip = &axp803_regmap_irq_chip;
> + break;
> case AXP806_ID:
> axp20x->nr_cells = ARRAY_SIZE(axp806_cells);
> axp20x->cells = axp806_cells;
> diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
> index dc8798cf2a24..cde56cfe8446 100644
> --- a/include/linux/mfd/axp20x.h
> +++ b/include/linux/mfd/axp20x.h
> @@ -20,6 +20,7 @@ enum axp20x_variants {
> AXP221_ID,
> AXP223_ID,
> AXP288_ID,
> + AXP803_ID,
> AXP806_ID,
> AXP809_ID,
> NR_AXP20X_VARIANTS,
> @@ -234,7 +235,7 @@ enum axp20x_variants {
> #define AXP22X_TS_ADC_L 0x59
> #define AXP22X_BATLOW_THRES1 0xe6
>
> -/* AXP288 specific registers */
> +/* AXP288/AXP803 specific registers */
> #define AXP288_POWER_REASON 0x02
> #define AXP288_BC_GLOBAL 0x2c
> #define AXP288_BC_VBUS_CNTL 0x2d
> @@ -475,6 +476,43 @@ enum axp288_irqs {
> AXP288_IRQ_BC_USB_CHNG,
> };
>
> +enum axp803_irqs {
> + AXP803_IRQ_ACIN_OVER_V = 1,
> + AXP803_IRQ_ACIN_PLUGIN,
> + AXP803_IRQ_ACIN_REMOVAL,
> + AXP803_IRQ_VBUS_OVER_V,
> + AXP803_IRQ_VBUS_PLUGIN,
> + AXP803_IRQ_VBUS_REMOVAL,
> + AXP803_IRQ_BATT_PLUGIN,
> + AXP803_IRQ_BATT_REMOVAL,
> + AXP803_IRQ_BATT_ENT_ACT_MODE,
> + AXP803_IRQ_BATT_EXIT_ACT_MODE,
> + AXP803_IRQ_CHARG,
> + AXP803_IRQ_CHARG_DONE,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH,
> + AXP803_IRQ_BATT_CHG_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW,
> + AXP803_IRQ_BATT_CHG_TEMP_LOW_END,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH,
> + AXP803_IRQ_BATT_ACT_TEMP_HIGH_END,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW,
> + AXP803_IRQ_BATT_ACT_TEMP_LOW_END,
> + AXP803_IRQ_DIE_TEMP_HIGH,
> + AXP803_IRQ_GPADC,
> + AXP803_IRQ_LOW_PWR_LVL1,
> + AXP803_IRQ_LOW_PWR_LVL2,
> + AXP803_IRQ_TIMER,
> + AXP803_IRQ_PEK_RIS_EDGE,
> + AXP803_IRQ_PEK_FAL_EDGE,
> + AXP803_IRQ_PEK_SHORT,
> + AXP803_IRQ_PEK_LONG,
> + AXP803_IRQ_PEK_OVER_OFF,
> + AXP803_IRQ_GPIO1_INPUT,
> + AXP803_IRQ_GPIO0_INPUT,
> + AXP803_IRQ_BC_USB_CHNG,
> + AXP803_IRQ_MV_CHNG,
> +};
> +
> enum axp806_irqs {
> AXP806_IRQ_DIE_TEMP_HIGH_LV1,
> AXP806_IRQ_DIE_TEMP_HIGH_LV2,
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2017-04-11 14:04 UTC|newest]
Thread overview: 71+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-04-07 18:34 [PATCH v2 00/11] AXP803 PMIC support for Pine64 Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 01/11] arm64: allwinner: a64: enable RSB on A64 Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 02/11] arm64: allwinner: a64: add NMI controller " Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 03/11] dt-bindings: add device tree binding for X-Powers AXP803 PMIC Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-11 14:04 ` Lee Jones
2017-04-11 14:04 ` Lee Jones
2017-04-11 14:04 ` Lee Jones
2017-04-11 15:00 ` Icenowy Zheng
2017-04-11 15:00 ` Icenowy Zheng
2017-04-11 15:00 ` Icenowy Zheng
2017-04-11 15:02 ` [linux-sunxi] " Chen-Yu Tsai
2017-04-11 15:02 ` Chen-Yu Tsai
2017-04-11 15:02 ` Chen-Yu Tsai
2017-04-11 16:29 ` [linux-sunxi] " Lee Jones
2017-04-11 16:29 ` Lee Jones
2017-04-11 16:29 ` Lee Jones
2017-04-13 19:56 ` Rob Herring
2017-04-13 19:56 ` Rob Herring
2017-04-13 19:56 ` Rob Herring
2017-04-07 18:34 ` [PATCH v2 04/11] mfd: axp20x: support AXP803 variant Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-11 14:04 ` Lee Jones [this message]
2017-04-11 14:04 ` Lee Jones
2017-04-11 14:04 ` Lee Jones
2017-04-07 18:34 ` [PATCH v2 05/11] arm64: allwinner: a64: add AXP803 node to Pine64 device tree Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 06/11] dt-bindings: add AXP803's regulator info Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-11 14:03 ` Lee Jones
2017-04-11 14:03 ` Lee Jones
2017-04-11 14:03 ` Lee Jones
2017-04-13 19:57 ` Rob Herring
2017-04-13 19:57 ` Rob Herring
2017-04-13 19:57 ` Rob Herring
2017-04-07 18:34 ` [PATCH v2 07/11] regulator: axp20x-regulator: add support for AXP803 Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-11 14:03 ` Lee Jones
2017-04-11 14:03 ` Lee Jones
2017-04-11 14:03 ` Lee Jones
2017-04-07 18:34 ` [PATCH v2 08/11] mfd: axp20x: add axp20x-regulator cell " Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-11 14:03 ` Lee Jones
2017-04-11 14:03 ` Lee Jones
2017-04-07 18:34 ` [PATCH v2 09/11] arm64: allwinner: a64: add DTSI file for AXP803 PMIC Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 10/11] arm64: allwinner: a64: enable AXP803 regulators for Pine64 Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` [PATCH v2 11/11] arm64: allwinner: a64: enable Wi-Fi " Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-07 18:34 ` Icenowy Zheng
2017-04-14 16:56 ` Andreas Färber
2017-04-14 16:56 ` Andreas Färber
2017-04-14 16:56 ` Andreas Färber
2017-04-17 7:59 ` Maxime Ripard
2017-04-17 7:59 ` Maxime Ripard
2017-04-17 7:59 ` Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170411140412.b2ncflm2iluuuai5@dell \
--to=lee.jones@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=icenowy@aosc.io \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=maxime.ripard@free-electrons.com \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.