From: Philippe Schenker <dev@pschenker.ch>
To: jic23@kernel.org, marcel.ziswiler@toradex.com, stefan@agner.ch
Cc: thierry.reding@gmail.com, Philippe Schenker <dev@pschenker.ch>,
Philippe Schenker <philippe.schenker@toradex.com>,
devicetree@vger.kernel.org,
Max Krummenacher <max.krummenacher@toradex.com>,
Alexandre Torgue <alexandre.torgue@st.com>,
linux-input@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Lee Jones <lee.jones@linaro.org>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Mark Rutland <mark.rutland@arm.com>,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH v4 1/8] dt-bindings: stmpe: reformatting parameter list and use tabs only
Date: Wed, 12 Dec 2018 14:06:42 +0100 [thread overview]
Message-ID: <20181212130649.15146-1-dev@pschenker.ch> (raw)
This patch reformats the parameter list for stmpe device in a
table-style so it is more clear to read.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---
Changes in v4:
- New separate precursor patch for holding reformatting
Changes in v3: None
Changes in v2: None
.../bindings/input/touchscreen/stmpe.txt | 52 ++++++++++++-------
.../devicetree/bindings/mfd/stmpe.txt | 14 ++---
2 files changed, 41 insertions(+), 25 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
index 127baa31a77a..1d3f84308142 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
@@ -5,24 +5,40 @@ Required properties:
- compatible: "st,stmpe-ts"
Optional properties:
-- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 ->
- 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6
- -> 144 clocks), recommended is 4.
-- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
-- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
- reference)
-- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
-- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4
- samples, 3 -> 8 samples)
-- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 ->
- 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended
- is 3
-- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3
- -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2
-- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of
- the fractional part) recommended is 7
-- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35
- mA max, 1 -> 50 mA typical 80 mA max)
+- st,sample-time : ADC conversion time in number of clock.
+ 0 -> 36 clocks 4 -> 80 clocks (recommended)
+ 1 -> 44 clocks 5 -> 96 clocks
+ 2 -> 56 clocks 6 -> 144 clocks
+ 3 -> 64 clocks
+- st,mod-12b : ADC Bit mode
+ 0 -> 10bit ADC 1 -> 12bit ADC
+- st,ref-sel : ADC reference source
+ 0 -> internal 1 -> external
+- st,adc-freq : ADC Clock speed
+ 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz
+ 1 -> 3.25 MHz
+- st,ave-ctrl : Sample average control
+ 0 -> 1 sample
+ 1 -> 2 samples
+ 2 -> 4 samples
+ 3 -> 8 samples
+- st,touch-det-delay : Touch detect interrupt delay (recommended is 3)
+ 0 -> 10 us 5 -> 5 ms
+ 1 -> 50 us 6 -> 10 ms
+ 2 -> 100 us 7 -> 50 ms
+ 3 -> 500 us
+ 4 -> 1 ms
+- st,settling : Panel driver settling time (recommended is 2)
+ 0 -> 10 us 5 -> 10 ms
+ 1 -> 100 us 6 for 50 ms
+ 2 -> 500 us 7 -> 100 ms
+ 3 -> 1 ms
+ 4 -> 5 ms
+- st,fraction-z : Length of the fractional part in z (recommended is 7)
+ (fraction-z ([0..7]) = Count of the fractional part)
+- st,i-drive : current limit value of the touchscreen drivers
+ 0 -> 20 mA (typical 35mA max)
+ 1 -> 50 mA (typical 80 mA max)
Node name must be stmpe_touchscreen and should be child node of stmpe node to
which it belongs.
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
index c797c05cd3c2..a46e7177195d 100644
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -4,15 +4,15 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio,
keypad, touchscreen, adc, pwm, rotator.
Required properties:
- - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
- - reg : I2C/SPI address of the device
+ - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
+ - reg : I2C/SPI address of the device
Optional properties:
- - interrupts : The interrupt outputs from the controller
- - interrupt-controller : Marks the device node as an interrupt controller
- - wakeup-source : Marks the input device as wakable
- - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
- - irq-gpio : If present, which GPIO to use for event IRQ
+ - interrupts : The interrupt outputs from the controller
+ - interrupt-controller : Marks the device node as an interrupt controller
+ - wakeup-source : Marks the input device as wakable
+ - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
+ - irq-gpio : If present, which GPIO to use for event IRQ
Example:
--
2.19.2
WARNING: multiple messages have this Message-ID (diff)
From: Philippe Schenker <dev@pschenker.ch>
To: jic23@kernel.org, marcel.ziswiler@toradex.com, stefan@agner.ch
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org,
Alexandre Torgue <alexandre.torgue@st.com>,
Dmitry Torokhov <dmitry.torokhov@gmail.com>,
linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
linux-stm32@st-md-mailman.stormreply.com,
Philippe Schenker <philippe.schenker@toradex.com>,
thierry.reding@gmail.com, linux-arm-kernel@lists.infradead.org,
Max Krummenacher <max.krummenacher@toradex.com>,
linux-input@vger.kernel.org, Lee Jones <lee.jones@linaro.org>,
Philippe Schenker <dev@pschenker.ch>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>
Subject: [PATCH v4 1/8] dt-bindings: stmpe: reformatting parameter list and use tabs only
Date: Wed, 12 Dec 2018 14:06:42 +0100 [thread overview]
Message-ID: <20181212130649.15146-1-dev@pschenker.ch> (raw)
This patch reformats the parameter list for stmpe device in a
table-style so it is more clear to read.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---
Changes in v4:
- New separate precursor patch for holding reformatting
Changes in v3: None
Changes in v2: None
.../bindings/input/touchscreen/stmpe.txt | 52 ++++++++++++-------
.../devicetree/bindings/mfd/stmpe.txt | 14 ++---
2 files changed, 41 insertions(+), 25 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
index 127baa31a77a..1d3f84308142 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
@@ -5,24 +5,40 @@ Required properties:
- compatible: "st,stmpe-ts"
Optional properties:
-- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 ->
- 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6
- -> 144 clocks), recommended is 4.
-- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
-- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
- reference)
-- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
-- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4
- samples, 3 -> 8 samples)
-- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 ->
- 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended
- is 3
-- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3
- -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2
-- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of
- the fractional part) recommended is 7
-- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35
- mA max, 1 -> 50 mA typical 80 mA max)
+- st,sample-time : ADC conversion time in number of clock.
+ 0 -> 36 clocks 4 -> 80 clocks (recommended)
+ 1 -> 44 clocks 5 -> 96 clocks
+ 2 -> 56 clocks 6 -> 144 clocks
+ 3 -> 64 clocks
+- st,mod-12b : ADC Bit mode
+ 0 -> 10bit ADC 1 -> 12bit ADC
+- st,ref-sel : ADC reference source
+ 0 -> internal 1 -> external
+- st,adc-freq : ADC Clock speed
+ 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz
+ 1 -> 3.25 MHz
+- st,ave-ctrl : Sample average control
+ 0 -> 1 sample
+ 1 -> 2 samples
+ 2 -> 4 samples
+ 3 -> 8 samples
+- st,touch-det-delay : Touch detect interrupt delay (recommended is 3)
+ 0 -> 10 us 5 -> 5 ms
+ 1 -> 50 us 6 -> 10 ms
+ 2 -> 100 us 7 -> 50 ms
+ 3 -> 500 us
+ 4 -> 1 ms
+- st,settling : Panel driver settling time (recommended is 2)
+ 0 -> 10 us 5 -> 10 ms
+ 1 -> 100 us 6 for 50 ms
+ 2 -> 500 us 7 -> 100 ms
+ 3 -> 1 ms
+ 4 -> 5 ms
+- st,fraction-z : Length of the fractional part in z (recommended is 7)
+ (fraction-z ([0..7]) = Count of the fractional part)
+- st,i-drive : current limit value of the touchscreen drivers
+ 0 -> 20 mA (typical 35mA max)
+ 1 -> 50 mA (typical 80 mA max)
Node name must be stmpe_touchscreen and should be child node of stmpe node to
which it belongs.
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
index c797c05cd3c2..a46e7177195d 100644
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -4,15 +4,15 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio,
keypad, touchscreen, adc, pwm, rotator.
Required properties:
- - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
- - reg : I2C/SPI address of the device
+ - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
+ - reg : I2C/SPI address of the device
Optional properties:
- - interrupts : The interrupt outputs from the controller
- - interrupt-controller : Marks the device node as an interrupt controller
- - wakeup-source : Marks the input device as wakable
- - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
- - irq-gpio : If present, which GPIO to use for event IRQ
+ - interrupts : The interrupt outputs from the controller
+ - interrupt-controller : Marks the device node as an interrupt controller
+ - wakeup-source : Marks the input device as wakable
+ - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
+ - irq-gpio : If present, which GPIO to use for event IRQ
Example:
--
2.19.2
WARNING: multiple messages have this Message-ID (diff)
From: Philippe Schenker <dev@pschenker.ch>
To: jic23@kernel.org, marcel.ziswiler@toradex.com, stefan@agner.ch
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org,
Alexandre Torgue <alexandre.torgue@st.com>,
Dmitry Torokhov <dmitry.torokhov@gmail.com>,
linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
linux-stm32@st-md-mailman.stormreply.com,
Philippe Schenker <philippe.schenker@toradex.com>,
thierry.reding@gmail.com, linux-arm-kernel@lists.infradead.org,
Max Krummenacher <max.krummenacher@toradex.com>,
linux-input@vger.kernel.org, Lee Jones <lee.jones@linaro.org>,
Philippe Schenker <dev@pschenker.ch>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>
Subject: [PATCH v4 1/8] dt-bindings: stmpe: reformatting parameter list and use tabs only
Date: Wed, 12 Dec 2018 14:06:42 +0100 [thread overview]
Message-ID: <20181212130649.15146-1-dev@pschenker.ch> (raw)
This patch reformats the parameter list for stmpe device in a
table-style so it is more clear to read.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
---
Changes in v4:
- New separate precursor patch for holding reformatting
Changes in v3: None
Changes in v2: None
.../bindings/input/touchscreen/stmpe.txt | 52 ++++++++++++-------
.../devicetree/bindings/mfd/stmpe.txt | 14 ++---
2 files changed, 41 insertions(+), 25 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
index 127baa31a77a..1d3f84308142 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
@@ -5,24 +5,40 @@ Required properties:
- compatible: "st,stmpe-ts"
Optional properties:
-- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 ->
- 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6
- -> 144 clocks), recommended is 4.
-- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
-- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external
- reference)
-- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
-- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4
- samples, 3 -> 8 samples)
-- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 ->
- 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended
- is 3
-- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3
- -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2
-- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of
- the fractional part) recommended is 7
-- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35
- mA max, 1 -> 50 mA typical 80 mA max)
+- st,sample-time : ADC conversion time in number of clock.
+ 0 -> 36 clocks 4 -> 80 clocks (recommended)
+ 1 -> 44 clocks 5 -> 96 clocks
+ 2 -> 56 clocks 6 -> 144 clocks
+ 3 -> 64 clocks
+- st,mod-12b : ADC Bit mode
+ 0 -> 10bit ADC 1 -> 12bit ADC
+- st,ref-sel : ADC reference source
+ 0 -> internal 1 -> external
+- st,adc-freq : ADC Clock speed
+ 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz
+ 1 -> 3.25 MHz
+- st,ave-ctrl : Sample average control
+ 0 -> 1 sample
+ 1 -> 2 samples
+ 2 -> 4 samples
+ 3 -> 8 samples
+- st,touch-det-delay : Touch detect interrupt delay (recommended is 3)
+ 0 -> 10 us 5 -> 5 ms
+ 1 -> 50 us 6 -> 10 ms
+ 2 -> 100 us 7 -> 50 ms
+ 3 -> 500 us
+ 4 -> 1 ms
+- st,settling : Panel driver settling time (recommended is 2)
+ 0 -> 10 us 5 -> 10 ms
+ 1 -> 100 us 6 for 50 ms
+ 2 -> 500 us 7 -> 100 ms
+ 3 -> 1 ms
+ 4 -> 5 ms
+- st,fraction-z : Length of the fractional part in z (recommended is 7)
+ (fraction-z ([0..7]) = Count of the fractional part)
+- st,i-drive : current limit value of the touchscreen drivers
+ 0 -> 20 mA (typical 35mA max)
+ 1 -> 50 mA (typical 80 mA max)
Node name must be stmpe_touchscreen and should be child node of stmpe node to
which it belongs.
diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt
index c797c05cd3c2..a46e7177195d 100644
--- a/Documentation/devicetree/bindings/mfd/stmpe.txt
+++ b/Documentation/devicetree/bindings/mfd/stmpe.txt
@@ -4,15 +4,15 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio,
keypad, touchscreen, adc, pwm, rotator.
Required properties:
- - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
- - reg : I2C/SPI address of the device
+ - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]"
+ - reg : I2C/SPI address of the device
Optional properties:
- - interrupts : The interrupt outputs from the controller
- - interrupt-controller : Marks the device node as an interrupt controller
- - wakeup-source : Marks the input device as wakable
- - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
- - irq-gpio : If present, which GPIO to use for event IRQ
+ - interrupts : The interrupt outputs from the controller
+ - interrupt-controller : Marks the device node as an interrupt controller
+ - wakeup-source : Marks the input device as wakable
+ - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024
+ - irq-gpio : If present, which GPIO to use for event IRQ
Example:
--
2.19.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2018-12-12 13:07 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-12 13:06 Philippe Schenker [this message]
2018-12-12 13:06 ` [PATCH v4 1/8] dt-bindings: stmpe: reformatting parameter list and use tabs only Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-12 13:06 ` [PATCH v4 2/8] mfd: stmpe: Move ADC related defines to header of mfd Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-12 13:06 ` [PATCH v4 3/8] mfd: stmpe: preparations for STMPE ADC driver Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-21 10:42 ` Lee Jones
2018-12-21 10:42 ` Lee Jones
2018-12-12 13:06 ` [PATCH v4 4/8] Input: stmpe-ts: " Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-12 13:06 ` [PATCH v4 5/8] iio: adc: add STMPE ADC driver using IIO framework Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-16 12:24 ` Jonathan Cameron
2018-12-16 12:24 ` Jonathan Cameron
2018-12-12 13:06 ` [PATCH v4 6/8] iio: adc: add STMPE ADC devicetree bindings Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-16 12:28 ` Jonathan Cameron
2018-12-16 12:28 ` Jonathan Cameron
2018-12-17 22:15 ` Rob Herring
2018-12-17 22:15 ` Rob Herring
2018-12-12 13:06 ` [PATCH v4 7/8] ARM: dts: Add stmpe-adc DT node to Toradex iMX6 modules Philippe Schenker
2018-12-12 13:06 ` Philippe Schenker
2018-12-12 13:06 ` [PATCH v4 8/8] ARM: dts: Add stmpe-adc DT node to Toradex T30 modules Philippe Schenker
2018-12-20 12:34 ` Dmitry Osipenko
2018-12-17 22:06 ` [PATCH v4 1/8] dt-bindings: stmpe: reformatting parameter list and use tabs only Rob Herring
2018-12-17 22:06 ` Rob Herring
2018-12-21 10:42 ` Lee Jones
2018-12-21 10:42 ` Lee Jones
2018-12-21 10:44 ` Lee Jones
2018-12-21 10:44 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181212130649.15146-1-dev@pschenker.ch \
--to=dev@pschenker.ch \
--cc=alexandre.torgue@st.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=jic23@kernel.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=marcel.ziswiler@toradex.com \
--cc=mark.rutland@arm.com \
--cc=max.krummenacher@toradex.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=philippe.schenker@toradex.com \
--cc=robh+dt@kernel.org \
--cc=stefan@agner.ch \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.