From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> To: ulf.hansson@linaro.org, afaerber@suse.de, robh+dt@kernel.org, sboyd@kernel.org Cc: linux-arm-kernel@lists.infradead.org, linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org, devicetree@vger.kernel.org, thomas.liau@actions-semi.com, linux-actions@lists.infradead.org, linus.walleij@linaro.org, linux-clk@vger.kernel.org, Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Subject: [PATCH v2 4/7] arm64: dts: actions: Add uSD and eMMC support for Bubblegum96 Date: Wed, 21 Aug 2019 08:10:11 +0530 [thread overview] Message-ID: <20190821024014.14070-5-manivannan.sadhasivam@linaro.org> (raw) In-Reply-To: <20190821024014.14070-1-manivannan.sadhasivam@linaro.org> Add uSD and eMMC support for Bubblegum96 board based on Actions Semi Owl SoC. SD0 is connected to uSD slot and SD2 is connected to eMMC. Since there is no PMIC support added yet, fixed regulator has been used as a regulator node. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../boot/dts/actions/s900-bubblegum-96.dts | 60 +++++++++++++++++++ 1 file changed, 60 insertions(+) diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts index 732daaa6e9d3..92376b71cb8f 100644 --- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts +++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts @@ -12,6 +12,9 @@ model = "Bubblegum-96"; aliases { + mmc0 = &mmc0; + mmc1 = &mmc1; + mmc2 = &mmc2; serial5 = &uart5; }; @@ -23,6 +26,22 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + vcc_3v1: vcc-3v1 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; + + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; }; &i2c0 { @@ -241,6 +260,47 @@ bias-pull-up; }; }; + + mmc0_default: mmc0_default { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + }; + + mmc2_default: mmc2_default { + pinmux { + groups = "nand0_d0_ceb3_mfp"; + function = "sd2"; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_default>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; +}; + +/* eMMC */ +&mmc2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_default>; + no-sdio; + no-sd; + non-removable; + bus-width = <8>; + vmmc-supply = <&vcc_3v1>; }; &timer { -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> To: ulf.hansson@linaro.org, afaerber@suse.de, robh+dt@kernel.org, sboyd@kernel.org Cc: devicetree@vger.kernel.org, linux-mmc@vger.kernel.org, linus.walleij@linaro.org, linux-actions@lists.infradead.org, linux-kernel@vger.kernel.org, thomas.liau@actions-semi.com, Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>, linux-clk@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 4/7] arm64: dts: actions: Add uSD and eMMC support for Bubblegum96 Date: Wed, 21 Aug 2019 08:10:11 +0530 [thread overview] Message-ID: <20190821024014.14070-5-manivannan.sadhasivam@linaro.org> (raw) In-Reply-To: <20190821024014.14070-1-manivannan.sadhasivam@linaro.org> Add uSD and eMMC support for Bubblegum96 board based on Actions Semi Owl SoC. SD0 is connected to uSD slot and SD2 is connected to eMMC. Since there is no PMIC support added yet, fixed regulator has been used as a regulator node. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../boot/dts/actions/s900-bubblegum-96.dts | 60 +++++++++++++++++++ 1 file changed, 60 insertions(+) diff --git a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts index 732daaa6e9d3..92376b71cb8f 100644 --- a/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts +++ b/arch/arm64/boot/dts/actions/s900-bubblegum-96.dts @@ -12,6 +12,9 @@ model = "Bubblegum-96"; aliases { + mmc0 = &mmc0; + mmc1 = &mmc1; + mmc2 = &mmc2; serial5 = &uart5; }; @@ -23,6 +26,22 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + vcc_3v1: vcc-3v1 { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; + + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; }; &i2c0 { @@ -241,6 +260,47 @@ bias-pull-up; }; }; + + mmc0_default: mmc0_default { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + }; + + mmc2_default: mmc2_default { + pinmux { + groups = "nand0_d0_ceb3_mfp"; + function = "sd2"; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_default>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; +}; + +/* eMMC */ +&mmc2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_default>; + no-sdio; + no-sd; + non-removable; + bus-width = <8>; + vmmc-supply = <&vcc_3v1>; }; &timer { -- 2.17.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-21 2:41 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-08-21 2:40 [PATCH v2 0/7] Add SD/MMC driver for Actions Semi S900 SoC Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 1/7] clk: actions: Fix factor clk struct member access Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 2/7] dt-bindings: mmc: Add Actions Semi SD/MMC/SDIO controller binding Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 3/7] arm64: dts: actions: Add MMC controller support for S900 Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam [this message] 2019-08-21 2:40 ` [PATCH v2 4/7] arm64: dts: actions: Add uSD and eMMC support for Bubblegum96 Manivannan Sadhasivam 2019-08-21 2:46 ` Manivannan Sadhasivam 2019-08-21 2:46 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 5/7] mmc: Add Actions Semi Owl SoCs SD/MMC driver Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 6/7] MAINTAINERS: Add entry for Actions Semi SD/MMC driver and binding Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam 2019-08-21 2:40 ` [PATCH v2 7/7] arm64: configs: Enable Actions Semi platform in defconfig Manivannan Sadhasivam 2019-08-21 2:40 ` Manivannan Sadhasivam
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190821024014.14070-5-manivannan.sadhasivam@linaro.org \ --to=manivannan.sadhasivam@linaro.org \ --cc=afaerber@suse.de \ --cc=devicetree@vger.kernel.org \ --cc=linus.walleij@linaro.org \ --cc=linux-actions@lists.infradead.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-clk@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-mmc@vger.kernel.org \ --cc=robh+dt@kernel.org \ --cc=sboyd@kernel.org \ --cc=thomas.liau@actions-semi.com \ --cc=ulf.hansson@linaro.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.