From: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: linux-arm-kernel@lists.infradead.org
Cc: "Nicolas Ferre" <nicolas.ferre@microchip.com>,
"Karl Rudbæk Olsen" <karl@micro-technic.com>,
linux-kernel@vger.kernel.org,
"Alexandre Belloni" <alexandre.belloni@bootlin.com>
Subject: [PATCH 1/2] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates
Date: Fri, 10 Jan 2020 18:20:06 +0100 [thread overview]
Message-ID: <20200110172007.1253659-1-alexandre.belloni@bootlin.com> (raw)
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
arch/arm/boot/dts/sama5d3.dtsi | 28 ++++++++++++++--------------
arch/arm/boot/dts/sama5d3_can.dtsi | 4 ++--
arch/arm/boot/dts/sama5d3_uart.dtsi | 4 ++--
3 files changed, 18 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index f770aace0efd..203d40be70a5 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -1188,49 +1188,49 @@ pioE_clk: pioE_clk {
usart0_clk: usart0_clk {
#clock-cells = <0>;
reg = <12>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart1_clk: usart1_clk {
#clock-cells = <0>;
reg = <13>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart2_clk: usart2_clk {
#clock-cells = <0>;
reg = <14>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart3_clk: usart3_clk {
#clock-cells = <0>;
reg = <15>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
twi0_clk: twi0_clk {
reg = <18>;
#clock-cells = <0>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi1_clk: twi1_clk {
#clock-cells = <0>;
reg = <19>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi2_clk: twi2_clk {
#clock-cells = <0>;
reg = <20>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
mci0_clk: mci0_clk {
@@ -1246,19 +1246,19 @@ mci1_clk: mci1_clk {
spi0_clk: spi0_clk {
#clock-cells = <0>;
reg = <24>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
spi1_clk: spi1_clk {
#clock-cells = <0>;
reg = <25>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
tcb0_clk: tcb0_clk {
#clock-cells = <0>;
reg = <26>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
pwm_clk: pwm_clk {
@@ -1269,7 +1269,7 @@ pwm_clk: pwm_clk {
adc_clk: adc_clk {
#clock-cells = <0>;
reg = <29>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
dma0_clk: dma0_clk {
@@ -1300,13 +1300,13 @@ isi_clk: isi_clk {
ssc0_clk: ssc0_clk {
#clock-cells = <0>;
reg = <38>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
ssc1_clk: ssc1_clk {
#clock-cells = <0>;
reg = <39>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
sha_clk: sha_clk {
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi
index cf06a018ed0f..2470dd3fff25 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/sama5d3_can.dtsi
@@ -36,13 +36,13 @@ periphck {
can0_clk: can0_clk {
#clock-cells = <0>;
reg = <40>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
can1_clk: can1_clk {
#clock-cells = <0>;
reg = <41>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index 4316bdbdc25d..cb62adbd28ed 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -41,13 +41,13 @@ periphck {
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart1_clk: uart1_clk {
#clock-cells = <0>;
reg = <17>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
--
2.24.1
WARNING: multiple messages have this Message-ID (diff)
From: Alexandre Belloni <alexandre.belloni@bootlin.com>
To: linux-arm-kernel@lists.infradead.org
Cc: "Alexandre Belloni" <alexandre.belloni@bootlin.com>,
"Karl Rudbæk Olsen" <karl@micro-technic.com>,
linux-kernel@vger.kernel.org
Subject: [PATCH 1/2] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates
Date: Fri, 10 Jan 2020 18:20:06 +0100 [thread overview]
Message-ID: <20200110172007.1253659-1-alexandre.belloni@bootlin.com> (raw)
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
arch/arm/boot/dts/sama5d3.dtsi | 28 ++++++++++++++--------------
arch/arm/boot/dts/sama5d3_can.dtsi | 4 ++--
arch/arm/boot/dts/sama5d3_uart.dtsi | 4 ++--
3 files changed, 18 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index f770aace0efd..203d40be70a5 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -1188,49 +1188,49 @@ pioE_clk: pioE_clk {
usart0_clk: usart0_clk {
#clock-cells = <0>;
reg = <12>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart1_clk: usart1_clk {
#clock-cells = <0>;
reg = <13>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart2_clk: usart2_clk {
#clock-cells = <0>;
reg = <14>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart3_clk: usart3_clk {
#clock-cells = <0>;
reg = <15>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
twi0_clk: twi0_clk {
reg = <18>;
#clock-cells = <0>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi1_clk: twi1_clk {
#clock-cells = <0>;
reg = <19>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi2_clk: twi2_clk {
#clock-cells = <0>;
reg = <20>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
mci0_clk: mci0_clk {
@@ -1246,19 +1246,19 @@ mci1_clk: mci1_clk {
spi0_clk: spi0_clk {
#clock-cells = <0>;
reg = <24>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
spi1_clk: spi1_clk {
#clock-cells = <0>;
reg = <25>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
tcb0_clk: tcb0_clk {
#clock-cells = <0>;
reg = <26>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
pwm_clk: pwm_clk {
@@ -1269,7 +1269,7 @@ pwm_clk: pwm_clk {
adc_clk: adc_clk {
#clock-cells = <0>;
reg = <29>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
dma0_clk: dma0_clk {
@@ -1300,13 +1300,13 @@ isi_clk: isi_clk {
ssc0_clk: ssc0_clk {
#clock-cells = <0>;
reg = <38>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
ssc1_clk: ssc1_clk {
#clock-cells = <0>;
reg = <39>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
sha_clk: sha_clk {
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi
index cf06a018ed0f..2470dd3fff25 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/sama5d3_can.dtsi
@@ -36,13 +36,13 @@ periphck {
can0_clk: can0_clk {
#clock-cells = <0>;
reg = <40>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
can1_clk: can1_clk {
#clock-cells = <0>;
reg = <41>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index 4316bdbdc25d..cb62adbd28ed 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -41,13 +41,13 @@ periphck {
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart1_clk: uart1_clk {
#clock-cells = <0>;
reg = <17>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
--
2.24.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next reply other threads:[~2020-01-10 17:20 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-10 17:20 Alexandre Belloni [this message]
2020-01-10 17:20 ` [PATCH 1/2] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates Alexandre Belloni
2020-01-10 17:20 ` [PATCH 2/2] ARM: dts: at91: sama5d3: define clock rate range for tcb1 Alexandre Belloni
2020-01-10 17:20 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200110172007.1253659-1-alexandre.belloni@bootlin.com \
--to=alexandre.belloni@bootlin.com \
--cc=karl@micro-technic.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.