From: Steen Hegelund <steen.hegelund@microchip.com>
To: "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Device Tree List <devicetree@vger.kernel.org>
Cc: Steen Hegelund <steen.hegelund@microchip.com>,
Andrew Lunn <andrew@lunn.ch>,
Russell King <linux@armlinux.org.uk>,
"Microchip Linux Driver Support" <UNGLinuxDriver@microchip.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Madalin Bucur <madalin.bucur@oss.nxp.com>,
Mark Einon <mark.einon@gmail.com>,
Masahiro Yamada <masahiroy@kernel.org>,
Arnd Bergmann <arnd@arndb.de>,
Philipp Zabel <p.zabel@pengutronix.de>,
"Simon Horman" <simon.horman@netronome.com>,
<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
"Lars Povlsen" <lars.povlsen@microchip.com>,
Bjarni Jonasson <bjarni.jonasson@microchip.com>
Subject: [PATCH net-next v4 10/10] arm64: dts: sparx5: Add the Sparx5 switch node
Date: Tue, 15 Jun 2021 10:50:34 +0200 [thread overview]
Message-ID: <20210615085034.1262457-11-steen.hegelund@microchip.com> (raw)
In-Reply-To: <20210615085034.1262457-1-steen.hegelund@microchip.com>
This provides the configuration for the currently available evaluation
boards PCB134 and PCB135.
The series depends on the following series currently on its way
into the kernel:
- Sparx5 Reset Driver
Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 94 ++-
.../dts/microchip/sparx5_pcb134_board.dtsi | 481 ++++++++++++--
.../dts/microchip/sparx5_pcb135_board.dtsi | 621 +++++++++++++++++-
3 files changed, 1112 insertions(+), 84 deletions(-)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index d64621d1213b..ad07fff40544 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -135,9 +135,12 @@ mux: mux-controller {
};
};
- reset@611010008 {
- compatible = "microchip,sparx5-chip-reset";
+ reset: reset-controller@611010008 {
+ compatible = "microchip,sparx5-switch-reset";
reg = <0x6 0x11010008 0x4>;
+ reg-names = "gcb";
+ #reset-cells = <1>;
+ cpu-syscon = <&cpu_ctrl>;
};
uart0: serial@600100000 {
@@ -275,6 +278,21 @@ emmc_pins: emmc-pins {
"GPIO_46", "GPIO_47";
function = "emmc";
};
+
+ miim1_pins: miim1-pins {
+ pins = "GPIO_56", "GPIO_57";
+ function = "miim";
+ };
+
+ miim2_pins: miim2-pins {
+ pins = "GPIO_58", "GPIO_59";
+ function = "miim";
+ };
+
+ miim3_pins: miim3-pins {
+ pins = "GPIO_52", "GPIO_53";
+ function = "miim";
+ };
};
sgpio0: gpio@61101036c {
@@ -285,6 +303,8 @@ sgpio0: gpio@61101036c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio0_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101036c 0x100>;
sgpio_in0: gpio@0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -292,6 +312,9 @@ sgpio_in0: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out0: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -310,6 +333,8 @@ sgpio1: gpio@611010484 {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio1_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x11010484 0x100>;
sgpio_in1: gpio@0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -317,6 +342,9 @@ sgpio_in1: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out1: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -335,6 +363,8 @@ sgpio2: gpio@61101059c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio2_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101059c 0x100>;
sgpio_in2: gpio@0 {
reg = <0>;
@@ -342,6 +372,9 @@ sgpio_in2: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out2: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -386,5 +419,62 @@ tmon0: tmon@610508110 {
#thermal-sensor-cells = <0>;
clocks = <&ahb_clk>;
};
+
+ mdio0: mdio@6110102b0 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102b0 0x24>;
+ };
+
+ mdio1: mdio@6110102d4 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim1_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio2: mdio@6110102f8 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim2_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio3: mdio@61101031c {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim3_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x1101031c 0x24>;
+ };
+
+ serdes: serdes@10808000 {
+ compatible = "microchip,sparx5-serdes";
+ #phy-cells = <1>;
+ clocks = <&sys_clk>;
+ reg = <0x6 0x10808000 0x5d0000>;
+ };
+
+ switch: switch@0x600000000 {
+ compatible = "microchip,sparx5-switch";
+ reg = <0x6 0 0x401000>,
+ <0x6 0x10004000 0x7fc000>,
+ <0x6 0x11010000 0xaf0000>;
+ reg-names = "cpu", "dev", "gcb";
+ interrupt-names = "xtr";
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&reset 0>;
+ reset-names = "switch";
+ };
};
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f0c915160990..33faf1f3264f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,30 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c100 = &i2c100;
- i2c101 = &i2c101;
- i2c102 = &i2c102;
- i2c103 = &i2c103;
- i2c104 = &i2c104;
- i2c105 = &i2c105;
- i2c106 = &i2c106;
- i2c107 = &i2c107;
- i2c108 = &i2c108;
- i2c109 = &i2c109;
- i2c110 = &i2c110;
- i2c111 = &i2c111;
- i2c112 = &i2c112;
- i2c113 = &i2c113;
- i2c114 = &i2c114;
- i2c115 = &i2c115;
- i2c116 = &i2c116;
- i2c117 = &i2c117;
- i2c118 = &i2c118;
- i2c119 = &i2c119;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -298,17 +274,10 @@ gpio@1 {
&spi0 {
status = "okay";
- spi@0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash@9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -328,6 +297,33 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <8 15>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <11 31>;
+};
+
&gpio {
i2cmux_pins_i: i2cmux-pins-i {
pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
@@ -415,9 +411,9 @@ i2c0_emux: i2c0-emux@0 {
&i2c0_imux {
pinctrl-names =
- "i2c100", "i2c101", "i2c102", "i2c103",
- "i2c104", "i2c105", "i2c106", "i2c107",
- "i2c108", "i2c109", "i2c110", "i2c111", "idle";
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
+ "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8",
+ "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle";
pinctrl-0 = <&i2cmux_0>;
pinctrl-1 = <&i2cmux_1>;
pinctrl-2 = <&i2cmux_2>;
@@ -431,62 +427,62 @@ &i2c0_imux {
pinctrl-10 = <&i2cmux_10>;
pinctrl-11 = <&i2cmux_11>;
pinctrl-12 = <&i2cmux_pins_i>;
- i2c100: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c101: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c102: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c103: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c104: i2c_sfp5 {
+ i2c_sfp5: i2c_sfp5 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c105: i2c_sfp6 {
+ i2c_sfp6: i2c_sfp6 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c106: i2c_sfp7 {
+ i2c_sfp7: i2c_sfp7 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c107: i2c_sfp8 {
+ i2c_sfp8: i2c_sfp8 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c108: i2c_sfp9 {
+ i2c_sfp9: i2c_sfp9 {
reg = <0x8>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c109: i2c_sfp10 {
+ i2c_sfp10: i2c_sfp10 {
reg = <0x9>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c110: i2c_sfp11 {
+ i2c_sfp11: i2c_sfp11 {
reg = <0xa>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c111: i2c_sfp12 {
+ i2c_sfp12: i2c_sfp12 {
reg = <0xb>;
#address-cells = <1>;
#size-cells = <0>;
@@ -499,44 +495,413 @@ &gpio 60 GPIO_ACTIVE_HIGH
&gpio 61 GPIO_ACTIVE_HIGH
&gpio 54 GPIO_ACTIVE_HIGH>;
idle-state = <0x8>;
- i2c112: i2c_sfp13 {
+ i2c_sfp13: i2c_sfp13 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c113: i2c_sfp14 {
+ i2c_sfp14: i2c_sfp14 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c114: i2c_sfp15 {
+ i2c_sfp15: i2c_sfp15 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c115: i2c_sfp16 {
+ i2c_sfp16: i2c_sfp16 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c116: i2c_sfp17 {
+ i2c_sfp17: i2c_sfp17 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c117: i2c_sfp18 {
+ i2c_sfp18: i2c_sfp18 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c118: i2c_sfp19 {
+ i2c_sfp19: i2c_sfp19 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c119: i2c_sfp20 {
+ i2c_sfp20: i2c_sfp20 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy@64 {
+ reg = <28>;
+ };
+};
+
+&axi {
+ sfp_eth12: sfp-eth12 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth13: sfp-eth13 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth14: sfp-eth14 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth15: sfp-eth15 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth48: sfp-eth48 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp5>;
+ tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth49: sfp-eth49 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp6>;
+ tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth50: sfp-eth50 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp7>;
+ tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth51: sfp-eth51 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp8>;
+ tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth52: sfp-eth52 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp9>;
+ tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth53: sfp-eth53 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp10>;
+ tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth54: sfp-eth54 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp11>;
+ tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth55: sfp-eth55 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp12>;
+ tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth56: sfp-eth56 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp13>;
+ tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth57: sfp-eth57 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp14>;
+ tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth58: sfp-eth58 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp15>;
+ tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth59: sfp-eth59 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp16>;
+ tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp17>;
+ tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp18>;
+ tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp19>;
+ tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp20>;
+ tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 10G SFPs */
+ port12: port@12 {
+ reg = <12>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 13>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth12>;
+ microchip,sd-sgpio = <301>;
+ managed = "in-band-status";
+ };
+ port13: port@13 {
+ reg = <13>;
+ /* Example: CU SFP, 1G speed */
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 14>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth13>;
+ microchip,sd-sgpio = <305>;
+ managed = "in-band-status";
+ };
+ port14: port@14 {
+ reg = <14>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 15>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth14>;
+ microchip,sd-sgpio = <309>;
+ managed = "in-band-status";
+ };
+ port15: port@15 {
+ reg = <15>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 16>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth15>;
+ microchip,sd-sgpio = <313>;
+ managed = "in-band-status";
+ };
+ port48: port@48 {
+ reg = <48>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 17>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth48>;
+ microchip,sd-sgpio = <317>;
+ managed = "in-band-status";
+ };
+ port49: port@49 {
+ reg = <49>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 18>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth49>;
+ microchip,sd-sgpio = <321>;
+ managed = "in-band-status";
+ };
+ port50: port@50 {
+ reg = <50>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 19>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth50>;
+ microchip,sd-sgpio = <325>;
+ managed = "in-band-status";
+ };
+ port51: port@51 {
+ reg = <51>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 20>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth51>;
+ microchip,sd-sgpio = <329>;
+ managed = "in-band-status";
+ };
+ port52: port@52 {
+ reg = <52>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 21>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth52>;
+ microchip,sd-sgpio = <333>;
+ managed = "in-band-status";
+ };
+ port53: port@53 {
+ reg = <53>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 22>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth53>;
+ microchip,sd-sgpio = <337>;
+ managed = "in-band-status";
+ };
+ port54: port@54 {
+ reg = <54>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 23>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth54>;
+ microchip,sd-sgpio = <341>;
+ managed = "in-band-status";
+ };
+ port55: port@55 {
+ reg = <55>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 24>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth55>;
+ microchip,sd-sgpio = <345>;
+ managed = "in-band-status";
+ };
+ /* 25G SFPs */
+ port56: port@56 {
+ reg = <56>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 25>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth56>;
+ microchip,sd-sgpio = <349>;
+ managed = "in-band-status";
+ };
+ port57: port@57 {
+ reg = <57>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 26>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth57>;
+ microchip,sd-sgpio = <353>;
+ managed = "in-band-status";
+ };
+ port58: port@58 {
+ reg = <58>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 27>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth58>;
+ microchip,sd-sgpio = <357>;
+ managed = "in-band-status";
+ };
+ port59: port@59 {
+ reg = <59>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 28>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth59>;
+ microchip,sd-sgpio = <361>;
+ managed = "in-band-status";
+ };
+ port60: port@60 {
+ reg = <60>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ microchip,sd-sgpio = <365>;
+ managed = "in-band-status";
+ };
+ port61: port@61 {
+ reg = <61>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ microchip,sd-sgpio = <369>;
+ managed = "in-band-status";
+ };
+ port62: port@62 {
+ reg = <62>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ microchip,sd-sgpio = <373>;
+ managed = "in-band-status";
+ };
+ port63: port@63 {
+ reg = <63>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ microchip,sd-sgpio = <377>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port@64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index e28c6dd16377..ef96e6d8c6b3 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,14 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c152 = &i2c152;
- i2c153 = &i2c153;
- i2c154 = &i2c154;
- i2c155 = &i2c155;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -97,17 +89,10 @@ i2cmux_s32: i2cmux-3 {
&spi0 {
status = "okay";
- spi@0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash@9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -138,6 +123,11 @@ gpio@1 {
};
};
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+};
+
&axi {
i2c0_imux: i2c0-imux@0 {
compatible = "i2c-mux-pinctrl";
@@ -149,31 +139,614 @@ i2c0_imux: i2c0-imux@0 {
&i2c0_imux {
pinctrl-names =
- "i2c152", "i2c153", "i2c154", "i2c155",
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
"idle";
pinctrl-0 = <&i2cmux_s29>;
pinctrl-1 = <&i2cmux_s30>;
pinctrl-2 = <&i2cmux_s31>;
pinctrl-3 = <&i2cmux_s32>;
pinctrl-4 = <&i2cmux_pins_i>;
- i2c152: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c153: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c154: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c155: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&axi {
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mdio0 {
+ status = "ok";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ phy6: ethernet-phy@6 {
+ reg = <6>;
+ };
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ };
+ phy8: ethernet-phy@8 {
+ reg = <8>;
+ };
+ phy9: ethernet-phy@9 {
+ reg = <9>;
+ };
+ phy10: ethernet-phy@10 {
+ reg = <10>;
+ };
+ phy11: ethernet-phy@11 {
+ reg = <11>;
+ };
+ phy12: ethernet-phy@12 {
+ reg = <12>;
+ };
+ phy13: ethernet-phy@13 {
+ reg = <13>;
+ };
+ phy14: ethernet-phy@14 {
+ reg = <14>;
+ };
+ phy15: ethernet-phy@15 {
+ reg = <15>;
+ };
+ phy16: ethernet-phy@16 {
+ reg = <16>;
+ };
+ phy17: ethernet-phy@17 {
+ reg = <17>;
+ };
+ phy18: ethernet-phy@18 {
+ reg = <18>;
+ };
+ phy19: ethernet-phy@19 {
+ reg = <19>;
+ };
+ phy20: ethernet-phy@20 {
+ reg = <20>;
+ };
+ phy21: ethernet-phy@21 {
+ reg = <21>;
+ };
+ phy22: ethernet-phy@22 {
+ reg = <22>;
+ };
+ phy23: ethernet-phy@23 {
+ reg = <23>;
+ };
+};
+
+&mdio1 {
+ status = "ok";
+ phy24: ethernet-phy@24 {
+ reg = <0>;
+ };
+ phy25: ethernet-phy@25 {
+ reg = <1>;
+ };
+ phy26: ethernet-phy@26 {
+ reg = <2>;
+ };
+ phy27: ethernet-phy@27 {
+ reg = <3>;
+ };
+ phy28: ethernet-phy@28 {
+ reg = <4>;
+ };
+ phy29: ethernet-phy@29 {
+ reg = <5>;
+ };
+ phy30: ethernet-phy@30 {
+ reg = <6>;
+ };
+ phy31: ethernet-phy@31 {
+ reg = <7>;
+ };
+ phy32: ethernet-phy@32 {
+ reg = <8>;
+ };
+ phy33: ethernet-phy@33 {
+ reg = <9>;
+ };
+ phy34: ethernet-phy@34 {
+ reg = <10>;
+ };
+ phy35: ethernet-phy@35 {
+ reg = <11>;
+ };
+ phy36: ethernet-phy@36 {
+ reg = <12>;
+ };
+ phy37: ethernet-phy@37 {
+ reg = <13>;
+ };
+ phy38: ethernet-phy@38 {
+ reg = <14>;
+ };
+ phy39: ethernet-phy@39 {
+ reg = <15>;
+ };
+ phy40: ethernet-phy@40 {
+ reg = <16>;
+ };
+ phy41: ethernet-phy@41 {
+ reg = <17>;
+ };
+ phy42: ethernet-phy@42 {
+ reg = <18>;
+ };
+ phy43: ethernet-phy@43 {
+ reg = <19>;
+ };
+ phy44: ethernet-phy@44 {
+ reg = <20>;
+ };
+ phy45: ethernet-phy@45 {
+ reg = <21>;
+ };
+ phy46: ethernet-phy@46 {
+ reg = <22>;
+ };
+ phy47: ethernet-phy@47 {
+ reg = <23>;
+ };
+};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy@64 {
+ reg = <28>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy0>;
+ phy-mode = "qsgmii";
+ };
+ port1: port@1 {
+ reg = <1>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy1>;
+ phy-mode = "qsgmii";
+ };
+ port2: port@2 {
+ reg = <2>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy2>;
+ phy-mode = "qsgmii";
+ };
+ port3: port@3 {
+ reg = <3>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy3>;
+ phy-mode = "qsgmii";
+ };
+ port4: port@4 {
+ reg = <4>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy4>;
+ phy-mode = "qsgmii";
+ };
+ port5: port@5 {
+ reg = <5>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy5>;
+ phy-mode = "qsgmii";
+ };
+ port6: port@6 {
+ reg = <6>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy6>;
+ phy-mode = "qsgmii";
+ };
+ port7: port@7 {
+ reg = <7>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy7>;
+ phy-mode = "qsgmii";
+ };
+ port8: port@8 {
+ reg = <8>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy8>;
+ phy-mode = "qsgmii";
+ };
+ port9: port@9 {
+ reg = <9>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy9>;
+ phy-mode = "qsgmii";
+ };
+ port10: port@10 {
+ reg = <10>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy10>;
+ phy-mode = "qsgmii";
+ };
+ port11: port@11 {
+ reg = <11>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy11>;
+ phy-mode = "qsgmii";
+ };
+ port12: port@12 {
+ reg = <12>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy12>;
+ phy-mode = "qsgmii";
+ };
+ port13: port@13 {
+ reg = <13>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy13>;
+ phy-mode = "qsgmii";
+ };
+ port14: port@14 {
+ reg = <14>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy14>;
+ phy-mode = "qsgmii";
+ };
+ port15: port@15 {
+ reg = <15>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy15>;
+ phy-mode = "qsgmii";
+ };
+ port16: port@16 {
+ reg = <16>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy16>;
+ phy-mode = "qsgmii";
+ };
+ port17: port@17 {
+ reg = <17>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy17>;
+ phy-mode = "qsgmii";
+ };
+ port18: port@18 {
+ reg = <18>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy18>;
+ phy-mode = "qsgmii";
+ };
+ port19: port@19 {
+ reg = <19>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy19>;
+ phy-mode = "qsgmii";
+ };
+ port20: port@20 {
+ reg = <20>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy20>;
+ phy-mode = "qsgmii";
+ };
+ port21: port@21 {
+ reg = <21>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy21>;
+ phy-mode = "qsgmii";
+ };
+ port22: port@22 {
+ reg = <22>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy22>;
+ phy-mode = "qsgmii";
+ };
+ port23: port@23 {
+ reg = <23>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy23>;
+ phy-mode = "qsgmii";
+ };
+ port24: port@24 {
+ reg = <24>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy24>;
+ phy-mode = "qsgmii";
+ };
+ port25: port@25 {
+ reg = <25>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy25>;
+ phy-mode = "qsgmii";
+ };
+ port26: port@26 {
+ reg = <26>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy26>;
+ phy-mode = "qsgmii";
+ };
+ port27: port@27 {
+ reg = <27>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy27>;
+ phy-mode = "qsgmii";
+ };
+ port28: port@28 {
+ reg = <28>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy28>;
+ phy-mode = "qsgmii";
+ };
+ port29: port@29 {
+ reg = <29>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy29>;
+ phy-mode = "qsgmii";
+ };
+ port30: port@30 {
+ reg = <30>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy30>;
+ phy-mode = "qsgmii";
+ };
+ port31: port@31 {
+ reg = <31>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy31>;
+ phy-mode = "qsgmii";
+ };
+ port32: port@32 {
+ reg = <32>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy32>;
+ phy-mode = "qsgmii";
+ };
+ port33: port@33 {
+ reg = <33>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy33>;
+ phy-mode = "qsgmii";
+ };
+ port34: port@34 {
+ reg = <34>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy34>;
+ phy-mode = "qsgmii";
+ };
+ port35: port@35 {
+ reg = <35>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy35>;
+ phy-mode = "qsgmii";
+ };
+ port36: port@36 {
+ reg = <36>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy36>;
+ phy-mode = "qsgmii";
+ };
+ port37: port@37 {
+ reg = <37>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy37>;
+ phy-mode = "qsgmii";
+ };
+ port38: port@38 {
+ reg = <38>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy38>;
+ phy-mode = "qsgmii";
+ };
+ port39: port@39 {
+ reg = <39>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy39>;
+ phy-mode = "qsgmii";
+ };
+ port40: port@40 {
+ reg = <40>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy40>;
+ phy-mode = "qsgmii";
+ };
+ port41: port@41 {
+ reg = <41>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy41>;
+ phy-mode = "qsgmii";
+ };
+ port42: port@42 {
+ reg = <42>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy42>;
+ phy-mode = "qsgmii";
+ };
+ port43: port@43 {
+ reg = <43>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy43>;
+ phy-mode = "qsgmii";
+ };
+ port44: port@44 {
+ reg = <44>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy44>;
+ phy-mode = "qsgmii";
+ };
+ port45: port@45 {
+ reg = <45>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy45>;
+ phy-mode = "qsgmii";
+ };
+ port46: port@46 {
+ reg = <46>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy46>;
+ phy-mode = "qsgmii";
+ };
+ port47: port@47 {
+ reg = <47>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy47>;
+ phy-mode = "qsgmii";
+ };
+ /* Then the 25G interfaces */
+ port60: port@60 {
+ reg = <60>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ managed = "in-band-status";
+ };
+ port61: port@61 {
+ reg = <61>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ managed = "in-band-status";
+ };
+ port62: port@62 {
+ reg = <62>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ managed = "in-band-status";
+ };
+ port63: port@63 {
+ reg = <63>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port@64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
--
2.32.0
WARNING: multiple messages have this Message-ID (diff)
From: Steen Hegelund <steen.hegelund@microchip.com>
To: "David S. Miller" <davem@davemloft.net>,
Jakub Kicinski <kuba@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Device Tree List <devicetree@vger.kernel.org>
Cc: Steen Hegelund <steen.hegelund@microchip.com>,
Andrew Lunn <andrew@lunn.ch>,
Russell King <linux@armlinux.org.uk>,
"Microchip Linux Driver Support" <UNGLinuxDriver@microchip.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Madalin Bucur <madalin.bucur@oss.nxp.com>,
Mark Einon <mark.einon@gmail.com>,
Masahiro Yamada <masahiroy@kernel.org>,
Arnd Bergmann <arnd@arndb.de>,
Philipp Zabel <p.zabel@pengutronix.de>,
"Simon Horman" <simon.horman@netronome.com>,
<netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
"Lars Povlsen" <lars.povlsen@microchip.com>,
Bjarni Jonasson <bjarni.jonasson@microchip.com>
Subject: [PATCH net-next v4 10/10] arm64: dts: sparx5: Add the Sparx5 switch node
Date: Tue, 15 Jun 2021 10:50:34 +0200 [thread overview]
Message-ID: <20210615085034.1262457-11-steen.hegelund@microchip.com> (raw)
In-Reply-To: <20210615085034.1262457-1-steen.hegelund@microchip.com>
This provides the configuration for the currently available evaluation
boards PCB134 and PCB135.
The series depends on the following series currently on its way
into the kernel:
- Sparx5 Reset Driver
Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
---
arch/arm64/boot/dts/microchip/sparx5.dtsi | 94 ++-
.../dts/microchip/sparx5_pcb134_board.dtsi | 481 ++++++++++++--
.../dts/microchip/sparx5_pcb135_board.dtsi | 621 +++++++++++++++++-
3 files changed, 1112 insertions(+), 84 deletions(-)
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index d64621d1213b..ad07fff40544 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -135,9 +135,12 @@ mux: mux-controller {
};
};
- reset@611010008 {
- compatible = "microchip,sparx5-chip-reset";
+ reset: reset-controller@611010008 {
+ compatible = "microchip,sparx5-switch-reset";
reg = <0x6 0x11010008 0x4>;
+ reg-names = "gcb";
+ #reset-cells = <1>;
+ cpu-syscon = <&cpu_ctrl>;
};
uart0: serial@600100000 {
@@ -275,6 +278,21 @@ emmc_pins: emmc-pins {
"GPIO_46", "GPIO_47";
function = "emmc";
};
+
+ miim1_pins: miim1-pins {
+ pins = "GPIO_56", "GPIO_57";
+ function = "miim";
+ };
+
+ miim2_pins: miim2-pins {
+ pins = "GPIO_58", "GPIO_59";
+ function = "miim";
+ };
+
+ miim3_pins: miim3-pins {
+ pins = "GPIO_52", "GPIO_53";
+ function = "miim";
+ };
};
sgpio0: gpio@61101036c {
@@ -285,6 +303,8 @@ sgpio0: gpio@61101036c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio0_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101036c 0x100>;
sgpio_in0: gpio@0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -292,6 +312,9 @@ sgpio_in0: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out0: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -310,6 +333,8 @@ sgpio1: gpio@611010484 {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio1_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x11010484 0x100>;
sgpio_in1: gpio@0 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -317,6 +342,9 @@ sgpio_in1: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out1: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -335,6 +363,8 @@ sgpio2: gpio@61101059c {
clocks = <&sys_clk>;
pinctrl-0 = <&sgpio2_pins>;
pinctrl-names = "default";
+ resets = <&reset 0>;
+ reset-names = "switch";
reg = <0x6 0x1101059c 0x100>;
sgpio_in2: gpio@0 {
reg = <0>;
@@ -342,6 +372,9 @@ sgpio_in2: gpio@0 {
gpio-controller;
#gpio-cells = <3>;
ngpios = <96>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
};
sgpio_out2: gpio@1 {
compatible = "microchip,sparx5-sgpio-bank";
@@ -386,5 +419,62 @@ tmon0: tmon@610508110 {
#thermal-sensor-cells = <0>;
clocks = <&ahb_clk>;
};
+
+ mdio0: mdio@6110102b0 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102b0 0x24>;
+ };
+
+ mdio1: mdio@6110102d4 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim1_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio2: mdio@6110102f8 {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim2_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x110102d4 0x24>;
+ };
+
+ mdio3: mdio@61101031c {
+ compatible = "mscc,ocelot-miim";
+ status = "disabled";
+ pinctrl-0 = <&miim3_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x6 0x1101031c 0x24>;
+ };
+
+ serdes: serdes@10808000 {
+ compatible = "microchip,sparx5-serdes";
+ #phy-cells = <1>;
+ clocks = <&sys_clk>;
+ reg = <0x6 0x10808000 0x5d0000>;
+ };
+
+ switch: switch@0x600000000 {
+ compatible = "microchip,sparx5-switch";
+ reg = <0x6 0 0x401000>,
+ <0x6 0x10004000 0x7fc000>,
+ <0x6 0x11010000 0xaf0000>;
+ reg-names = "cpu", "dev", "gcb";
+ interrupt-names = "xtr";
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&reset 0>;
+ reset-names = "switch";
+ };
};
};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f0c915160990..33faf1f3264f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,30 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c100 = &i2c100;
- i2c101 = &i2c101;
- i2c102 = &i2c102;
- i2c103 = &i2c103;
- i2c104 = &i2c104;
- i2c105 = &i2c105;
- i2c106 = &i2c106;
- i2c107 = &i2c107;
- i2c108 = &i2c108;
- i2c109 = &i2c109;
- i2c110 = &i2c110;
- i2c111 = &i2c111;
- i2c112 = &i2c112;
- i2c113 = &i2c113;
- i2c114 = &i2c114;
- i2c115 = &i2c115;
- i2c116 = &i2c116;
- i2c117 = &i2c117;
- i2c118 = &i2c118;
- i2c119 = &i2c119;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -298,17 +274,10 @@ gpio@1 {
&spi0 {
status = "okay";
- spi@0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash@9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -328,6 +297,33 @@ spi-flash@9 {
};
};
+&sgpio0 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <8 15>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio1 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <24 31>;
+ gpio@0 {
+ ngpios = <64>;
+ };
+ gpio@1 {
+ ngpios = <64>;
+ };
+};
+
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <11 31>;
+};
+
&gpio {
i2cmux_pins_i: i2cmux-pins-i {
pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
@@ -415,9 +411,9 @@ i2c0_emux: i2c0-emux@0 {
&i2c0_imux {
pinctrl-names =
- "i2c100", "i2c101", "i2c102", "i2c103",
- "i2c104", "i2c105", "i2c106", "i2c107",
- "i2c108", "i2c109", "i2c110", "i2c111", "idle";
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
+ "i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8",
+ "i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle";
pinctrl-0 = <&i2cmux_0>;
pinctrl-1 = <&i2cmux_1>;
pinctrl-2 = <&i2cmux_2>;
@@ -431,62 +427,62 @@ &i2c0_imux {
pinctrl-10 = <&i2cmux_10>;
pinctrl-11 = <&i2cmux_11>;
pinctrl-12 = <&i2cmux_pins_i>;
- i2c100: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c101: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c102: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c103: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c104: i2c_sfp5 {
+ i2c_sfp5: i2c_sfp5 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c105: i2c_sfp6 {
+ i2c_sfp6: i2c_sfp6 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c106: i2c_sfp7 {
+ i2c_sfp7: i2c_sfp7 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c107: i2c_sfp8 {
+ i2c_sfp8: i2c_sfp8 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c108: i2c_sfp9 {
+ i2c_sfp9: i2c_sfp9 {
reg = <0x8>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c109: i2c_sfp10 {
+ i2c_sfp10: i2c_sfp10 {
reg = <0x9>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c110: i2c_sfp11 {
+ i2c_sfp11: i2c_sfp11 {
reg = <0xa>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c111: i2c_sfp12 {
+ i2c_sfp12: i2c_sfp12 {
reg = <0xb>;
#address-cells = <1>;
#size-cells = <0>;
@@ -499,44 +495,413 @@ &gpio 60 GPIO_ACTIVE_HIGH
&gpio 61 GPIO_ACTIVE_HIGH
&gpio 54 GPIO_ACTIVE_HIGH>;
idle-state = <0x8>;
- i2c112: i2c_sfp13 {
+ i2c_sfp13: i2c_sfp13 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c113: i2c_sfp14 {
+ i2c_sfp14: i2c_sfp14 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c114: i2c_sfp15 {
+ i2c_sfp15: i2c_sfp15 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c115: i2c_sfp16 {
+ i2c_sfp16: i2c_sfp16 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c116: i2c_sfp17 {
+ i2c_sfp17: i2c_sfp17 {
reg = <0x4>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c117: i2c_sfp18 {
+ i2c_sfp18: i2c_sfp18 {
reg = <0x5>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c118: i2c_sfp19 {
+ i2c_sfp19: i2c_sfp19 {
reg = <0x6>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c119: i2c_sfp20 {
+ i2c_sfp20: i2c_sfp20 {
reg = <0x7>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy@64 {
+ reg = <28>;
+ };
+};
+
+&axi {
+ sfp_eth12: sfp-eth12 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth13: sfp-eth13 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth14: sfp-eth14 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth15: sfp-eth15 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth48: sfp-eth48 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp5>;
+ tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth49: sfp-eth49 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp6>;
+ tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth50: sfp-eth50 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp7>;
+ tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth51: sfp-eth51 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp8>;
+ tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth52: sfp-eth52 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp9>;
+ tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth53: sfp-eth53 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp10>;
+ tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth54: sfp-eth54 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp11>;
+ tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth55: sfp-eth55 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp12>;
+ tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth56: sfp-eth56 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp13>;
+ tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth57: sfp-eth57 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp14>;
+ tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth58: sfp-eth58 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp15>;
+ tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth59: sfp-eth59 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp16>;
+ tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp17>;
+ tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp18>;
+ tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp19>;
+ tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp20>;
+ tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
+ los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 10G SFPs */
+ port12: port@12 {
+ reg = <12>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 13>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth12>;
+ microchip,sd-sgpio = <301>;
+ managed = "in-band-status";
+ };
+ port13: port@13 {
+ reg = <13>;
+ /* Example: CU SFP, 1G speed */
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 14>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth13>;
+ microchip,sd-sgpio = <305>;
+ managed = "in-band-status";
+ };
+ port14: port@14 {
+ reg = <14>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 15>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth14>;
+ microchip,sd-sgpio = <309>;
+ managed = "in-band-status";
+ };
+ port15: port@15 {
+ reg = <15>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 16>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth15>;
+ microchip,sd-sgpio = <313>;
+ managed = "in-band-status";
+ };
+ port48: port@48 {
+ reg = <48>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 17>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth48>;
+ microchip,sd-sgpio = <317>;
+ managed = "in-band-status";
+ };
+ port49: port@49 {
+ reg = <49>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 18>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth49>;
+ microchip,sd-sgpio = <321>;
+ managed = "in-band-status";
+ };
+ port50: port@50 {
+ reg = <50>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 19>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth50>;
+ microchip,sd-sgpio = <325>;
+ managed = "in-band-status";
+ };
+ port51: port@51 {
+ reg = <51>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 20>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth51>;
+ microchip,sd-sgpio = <329>;
+ managed = "in-band-status";
+ };
+ port52: port@52 {
+ reg = <52>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 21>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth52>;
+ microchip,sd-sgpio = <333>;
+ managed = "in-band-status";
+ };
+ port53: port@53 {
+ reg = <53>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 22>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth53>;
+ microchip,sd-sgpio = <337>;
+ managed = "in-band-status";
+ };
+ port54: port@54 {
+ reg = <54>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 23>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth54>;
+ microchip,sd-sgpio = <341>;
+ managed = "in-band-status";
+ };
+ port55: port@55 {
+ reg = <55>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 24>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth55>;
+ microchip,sd-sgpio = <345>;
+ managed = "in-band-status";
+ };
+ /* 25G SFPs */
+ port56: port@56 {
+ reg = <56>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 25>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth56>;
+ microchip,sd-sgpio = <349>;
+ managed = "in-band-status";
+ };
+ port57: port@57 {
+ reg = <57>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 26>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth57>;
+ microchip,sd-sgpio = <353>;
+ managed = "in-band-status";
+ };
+ port58: port@58 {
+ reg = <58>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 27>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth58>;
+ microchip,sd-sgpio = <357>;
+ managed = "in-band-status";
+ };
+ port59: port@59 {
+ reg = <59>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 28>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth59>;
+ microchip,sd-sgpio = <361>;
+ managed = "in-band-status";
+ };
+ port60: port@60 {
+ reg = <60>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ microchip,sd-sgpio = <365>;
+ managed = "in-band-status";
+ };
+ port61: port@61 {
+ reg = <61>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ microchip,sd-sgpio = <369>;
+ managed = "in-band-status";
+ };
+ port62: port@62 {
+ reg = <62>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ microchip,sd-sgpio = <373>;
+ managed = "in-band-status";
+ };
+ port63: port@63 {
+ reg = <63>;
+ microchip,bandwidth = <10000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ microchip,sd-sgpio = <377>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port@64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index e28c6dd16377..ef96e6d8c6b3 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,14 +7,6 @@
#include "sparx5_pcb_common.dtsi"
/{
- aliases {
- i2c0 = &i2c0;
- i2c152 = &i2c152;
- i2c153 = &i2c153;
- i2c154 = &i2c154;
- i2c155 = &i2c155;
- };
-
gpio-restart {
compatible = "gpio-restart";
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -97,17 +89,10 @@ i2cmux_s32: i2cmux-3 {
&spi0 {
status = "okay";
- spi@0 {
- compatible = "spi-mux";
- mux-controls = <&mux>;
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>; /* CS0 */
- spi-flash@9 {
- compatible = "jedec,spi-nor";
- spi-max-frequency = <8000000>;
- reg = <0x9>; /* SPI */
- };
+ spi-flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <8000000>;
+ reg = <0>;
};
};
@@ -138,6 +123,11 @@ gpio@1 {
};
};
+&sgpio2 {
+ status = "okay";
+ microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+};
+
&axi {
i2c0_imux: i2c0-imux@0 {
compatible = "i2c-mux-pinctrl";
@@ -149,31 +139,614 @@ i2c0_imux: i2c0-imux@0 {
&i2c0_imux {
pinctrl-names =
- "i2c152", "i2c153", "i2c154", "i2c155",
+ "i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
"idle";
pinctrl-0 = <&i2cmux_s29>;
pinctrl-1 = <&i2cmux_s30>;
pinctrl-2 = <&i2cmux_s31>;
pinctrl-3 = <&i2cmux_s32>;
pinctrl-4 = <&i2cmux_pins_i>;
- i2c152: i2c_sfp1 {
+ i2c_sfp1: i2c_sfp1 {
reg = <0x0>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c153: i2c_sfp2 {
+ i2c_sfp2: i2c_sfp2 {
reg = <0x1>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c154: i2c_sfp3 {
+ i2c_sfp3: i2c_sfp3 {
reg = <0x2>;
#address-cells = <1>;
#size-cells = <0>;
};
- i2c155: i2c_sfp4 {
+ i2c_sfp4: i2c_sfp4 {
reg = <0x3>;
#address-cells = <1>;
#size-cells = <0>;
};
};
+
+&axi {
+ sfp_eth60: sfp-eth60 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp1>;
+ tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth61: sfp-eth61 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp2>;
+ tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth62: sfp-eth62 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp3>;
+ tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+ };
+ sfp_eth63: sfp-eth63 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c_sfp4>;
+ tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+ rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+ los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+ tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mdio0 {
+ status = "ok";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+ phy5: ethernet-phy@5 {
+ reg = <5>;
+ };
+ phy6: ethernet-phy@6 {
+ reg = <6>;
+ };
+ phy7: ethernet-phy@7 {
+ reg = <7>;
+ };
+ phy8: ethernet-phy@8 {
+ reg = <8>;
+ };
+ phy9: ethernet-phy@9 {
+ reg = <9>;
+ };
+ phy10: ethernet-phy@10 {
+ reg = <10>;
+ };
+ phy11: ethernet-phy@11 {
+ reg = <11>;
+ };
+ phy12: ethernet-phy@12 {
+ reg = <12>;
+ };
+ phy13: ethernet-phy@13 {
+ reg = <13>;
+ };
+ phy14: ethernet-phy@14 {
+ reg = <14>;
+ };
+ phy15: ethernet-phy@15 {
+ reg = <15>;
+ };
+ phy16: ethernet-phy@16 {
+ reg = <16>;
+ };
+ phy17: ethernet-phy@17 {
+ reg = <17>;
+ };
+ phy18: ethernet-phy@18 {
+ reg = <18>;
+ };
+ phy19: ethernet-phy@19 {
+ reg = <19>;
+ };
+ phy20: ethernet-phy@20 {
+ reg = <20>;
+ };
+ phy21: ethernet-phy@21 {
+ reg = <21>;
+ };
+ phy22: ethernet-phy@22 {
+ reg = <22>;
+ };
+ phy23: ethernet-phy@23 {
+ reg = <23>;
+ };
+};
+
+&mdio1 {
+ status = "ok";
+ phy24: ethernet-phy@24 {
+ reg = <0>;
+ };
+ phy25: ethernet-phy@25 {
+ reg = <1>;
+ };
+ phy26: ethernet-phy@26 {
+ reg = <2>;
+ };
+ phy27: ethernet-phy@27 {
+ reg = <3>;
+ };
+ phy28: ethernet-phy@28 {
+ reg = <4>;
+ };
+ phy29: ethernet-phy@29 {
+ reg = <5>;
+ };
+ phy30: ethernet-phy@30 {
+ reg = <6>;
+ };
+ phy31: ethernet-phy@31 {
+ reg = <7>;
+ };
+ phy32: ethernet-phy@32 {
+ reg = <8>;
+ };
+ phy33: ethernet-phy@33 {
+ reg = <9>;
+ };
+ phy34: ethernet-phy@34 {
+ reg = <10>;
+ };
+ phy35: ethernet-phy@35 {
+ reg = <11>;
+ };
+ phy36: ethernet-phy@36 {
+ reg = <12>;
+ };
+ phy37: ethernet-phy@37 {
+ reg = <13>;
+ };
+ phy38: ethernet-phy@38 {
+ reg = <14>;
+ };
+ phy39: ethernet-phy@39 {
+ reg = <15>;
+ };
+ phy40: ethernet-phy@40 {
+ reg = <16>;
+ };
+ phy41: ethernet-phy@41 {
+ reg = <17>;
+ };
+ phy42: ethernet-phy@42 {
+ reg = <18>;
+ };
+ phy43: ethernet-phy@43 {
+ reg = <19>;
+ };
+ phy44: ethernet-phy@44 {
+ reg = <20>;
+ };
+ phy45: ethernet-phy@45 {
+ reg = <21>;
+ };
+ phy46: ethernet-phy@46 {
+ reg = <22>;
+ };
+ phy47: ethernet-phy@47 {
+ reg = <23>;
+ };
+};
+
+&mdio3 {
+ status = "ok";
+ phy64: ethernet-phy@64 {
+ reg = <28>;
+ };
+};
+
+&switch {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy0>;
+ phy-mode = "qsgmii";
+ };
+ port1: port@1 {
+ reg = <1>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy1>;
+ phy-mode = "qsgmii";
+ };
+ port2: port@2 {
+ reg = <2>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy2>;
+ phy-mode = "qsgmii";
+ };
+ port3: port@3 {
+ reg = <3>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 13>;
+ phy-handle = <&phy3>;
+ phy-mode = "qsgmii";
+ };
+ port4: port@4 {
+ reg = <4>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy4>;
+ phy-mode = "qsgmii";
+ };
+ port5: port@5 {
+ reg = <5>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy5>;
+ phy-mode = "qsgmii";
+ };
+ port6: port@6 {
+ reg = <6>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy6>;
+ phy-mode = "qsgmii";
+ };
+ port7: port@7 {
+ reg = <7>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 14>;
+ phy-handle = <&phy7>;
+ phy-mode = "qsgmii";
+ };
+ port8: port@8 {
+ reg = <8>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy8>;
+ phy-mode = "qsgmii";
+ };
+ port9: port@9 {
+ reg = <9>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy9>;
+ phy-mode = "qsgmii";
+ };
+ port10: port@10 {
+ reg = <10>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy10>;
+ phy-mode = "qsgmii";
+ };
+ port11: port@11 {
+ reg = <11>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 15>;
+ phy-handle = <&phy11>;
+ phy-mode = "qsgmii";
+ };
+ port12: port@12 {
+ reg = <12>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy12>;
+ phy-mode = "qsgmii";
+ };
+ port13: port@13 {
+ reg = <13>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy13>;
+ phy-mode = "qsgmii";
+ };
+ port14: port@14 {
+ reg = <14>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy14>;
+ phy-mode = "qsgmii";
+ };
+ port15: port@15 {
+ reg = <15>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 16>;
+ phy-handle = <&phy15>;
+ phy-mode = "qsgmii";
+ };
+ port16: port@16 {
+ reg = <16>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy16>;
+ phy-mode = "qsgmii";
+ };
+ port17: port@17 {
+ reg = <17>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy17>;
+ phy-mode = "qsgmii";
+ };
+ port18: port@18 {
+ reg = <18>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy18>;
+ phy-mode = "qsgmii";
+ };
+ port19: port@19 {
+ reg = <19>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 17>;
+ phy-handle = <&phy19>;
+ phy-mode = "qsgmii";
+ };
+ port20: port@20 {
+ reg = <20>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy20>;
+ phy-mode = "qsgmii";
+ };
+ port21: port@21 {
+ reg = <21>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy21>;
+ phy-mode = "qsgmii";
+ };
+ port22: port@22 {
+ reg = <22>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy22>;
+ phy-mode = "qsgmii";
+ };
+ port23: port@23 {
+ reg = <23>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 18>;
+ phy-handle = <&phy23>;
+ phy-mode = "qsgmii";
+ };
+ port24: port@24 {
+ reg = <24>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy24>;
+ phy-mode = "qsgmii";
+ };
+ port25: port@25 {
+ reg = <25>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy25>;
+ phy-mode = "qsgmii";
+ };
+ port26: port@26 {
+ reg = <26>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy26>;
+ phy-mode = "qsgmii";
+ };
+ port27: port@27 {
+ reg = <27>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 19>;
+ phy-handle = <&phy27>;
+ phy-mode = "qsgmii";
+ };
+ port28: port@28 {
+ reg = <28>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy28>;
+ phy-mode = "qsgmii";
+ };
+ port29: port@29 {
+ reg = <29>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy29>;
+ phy-mode = "qsgmii";
+ };
+ port30: port@30 {
+ reg = <30>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy30>;
+ phy-mode = "qsgmii";
+ };
+ port31: port@31 {
+ reg = <31>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 20>;
+ phy-handle = <&phy31>;
+ phy-mode = "qsgmii";
+ };
+ port32: port@32 {
+ reg = <32>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy32>;
+ phy-mode = "qsgmii";
+ };
+ port33: port@33 {
+ reg = <33>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy33>;
+ phy-mode = "qsgmii";
+ };
+ port34: port@34 {
+ reg = <34>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy34>;
+ phy-mode = "qsgmii";
+ };
+ port35: port@35 {
+ reg = <35>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 21>;
+ phy-handle = <&phy35>;
+ phy-mode = "qsgmii";
+ };
+ port36: port@36 {
+ reg = <36>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy36>;
+ phy-mode = "qsgmii";
+ };
+ port37: port@37 {
+ reg = <37>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy37>;
+ phy-mode = "qsgmii";
+ };
+ port38: port@38 {
+ reg = <38>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy38>;
+ phy-mode = "qsgmii";
+ };
+ port39: port@39 {
+ reg = <39>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 22>;
+ phy-handle = <&phy39>;
+ phy-mode = "qsgmii";
+ };
+ port40: port@40 {
+ reg = <40>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy40>;
+ phy-mode = "qsgmii";
+ };
+ port41: port@41 {
+ reg = <41>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy41>;
+ phy-mode = "qsgmii";
+ };
+ port42: port@42 {
+ reg = <42>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy42>;
+ phy-mode = "qsgmii";
+ };
+ port43: port@43 {
+ reg = <43>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 23>;
+ phy-handle = <&phy43>;
+ phy-mode = "qsgmii";
+ };
+ port44: port@44 {
+ reg = <44>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy44>;
+ phy-mode = "qsgmii";
+ };
+ port45: port@45 {
+ reg = <45>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy45>;
+ phy-mode = "qsgmii";
+ };
+ port46: port@46 {
+ reg = <46>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy46>;
+ phy-mode = "qsgmii";
+ };
+ port47: port@47 {
+ reg = <47>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 24>;
+ phy-handle = <&phy47>;
+ phy-mode = "qsgmii";
+ };
+ /* Then the 25G interfaces */
+ port60: port@60 {
+ reg = <60>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 29>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth60>;
+ managed = "in-band-status";
+ };
+ port61: port@61 {
+ reg = <61>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 30>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth61>;
+ managed = "in-band-status";
+ };
+ port62: port@62 {
+ reg = <62>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 31>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth62>;
+ managed = "in-band-status";
+ };
+ port63: port@63 {
+ reg = <63>;
+ microchip,bandwidth = <25000>;
+ phys = <&serdes 32>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp_eth63>;
+ managed = "in-band-status";
+ };
+ /* Finally the Management interface */
+ port64: port@64 {
+ reg = <64>;
+ microchip,bandwidth = <1000>;
+ phys = <&serdes 0>;
+ phy-handle = <&phy64>;
+ phy-mode = "sgmii";
+ };
+ };
+};
--
2.32.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-06-15 8:52 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-15 8:50 [PATCH net-next v4 00/10] Adding the Sparx5 Switch Driver Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 01/10] dt-bindings: net: sparx5: Add sparx5-switch bindings Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 02/10] net: sparx5: add the basic sparx5 driver Steen Hegelund
2021-06-15 13:22 ` Philipp Zabel
2021-06-15 13:22 ` Philipp Zabel
2021-06-16 6:20 ` Steen Hegelund
2021-06-16 6:20 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 03/10] net: sparx5: add hostmode with phylink support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-21 14:26 ` Russell King (Oracle)
2021-06-21 14:26 ` Russell King (Oracle)
2021-06-23 13:04 ` Steen Hegelund
2021-06-23 13:04 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 04/10] net: sparx5: add port module support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-21 14:33 ` Russell King (Oracle)
2021-06-21 14:33 ` Russell King (Oracle)
2021-06-23 13:05 ` Steen Hegelund
2021-06-23 13:05 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 05/10] net: sparx5: add mactable support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 06/10] net: sparx5: add vlan support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 07/10] net: sparx5: add switching support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 08/10] net: sparx5: add calendar bandwidth allocation support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` [PATCH net-next v4 09/10] net: sparx5: add ethtool configuration and statistics support Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund
2021-06-15 8:50 ` Steen Hegelund [this message]
2021-06-15 8:50 ` [PATCH net-next v4 10/10] arm64: dts: sparx5: Add the Sparx5 switch node Steen Hegelund
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210615085034.1262457-11-steen.hegelund@microchip.com \
--to=steen.hegelund@microchip.com \
--cc=UNGLinuxDriver@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=andrew@lunn.ch \
--cc=arnd@arndb.de \
--cc=bjarni.jonasson@microchip.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=kuba@kernel.org \
--cc=lars.povlsen@microchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=madalin.bucur@oss.nxp.com \
--cc=mark.einon@gmail.com \
--cc=masahiroy@kernel.org \
--cc=netdev@vger.kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=simon.horman@netronome.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.