From: Anand Moon <linux.amoon@gmail.com>
To: linux-phy@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: Anand Moon <linux.amoon@gmail.com>,
Matt Corallo <oc2udbzfd@mattcorallo.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Rob Herring <robh+dt@kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Emiliano Ingrassia <ingrassia@epigenesys.com>,
devicetree@vger.kernel.org
Subject: [PATCHv1 1/3] ARM: dts: meson8b: odroidc1: Add usb phy power node
Date: Tue, 13 Jul 2021 05:52:13 +0000 [thread overview]
Message-ID: <20210713055227.1142-2-linux.amoon@gmail.com> (raw)
In-Reply-To: <20210713055227.1142-1-linux.amoon@gmail.com>
Add missing usb phy power node for phy mode fix below warning.
[ 1.253149] phy phy-c1108820.phy.0: Looking up phy-supply from device tree
[ 1.253166] phy phy-c1108820.phy.0: Looking up phy-supply property
in node /soc/cbus@c1100000/phy@8820 failed
Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host
controller on Odroid-C1/C1+ board)
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
previous version
[0] https://patchwork.kernel.org/project/linux-amlogic/patch/20190113181808.5768-1-linux.amoon@gmail.com
changes fix the vbus-suppy to phy-supply, drop enable usb0
# sudo cat /sys/kernel/debug/regulator/regulator_summary
USB_PWR 2 1 0 unknown 5000mV 0mA 5000mV 5000mV
phy-c1108820.phy.0-phy 2 0mA 0mV 0mV
---
arch/arm/boot/dts/meson8b-odroidc1.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index c440ef94e082..ced1ec1c4878 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -32,6 +32,25 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+ usb_pwr_en: regulator-usb-pwr-en {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
+
+ /*
+ * signal name from schematics: PWREN
+ */
+ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
leds {
compatible = "gpio-leds";
blue {
@@ -378,6 +397,7 @@ &uart_AO {
&usb1_phy {
status = "okay";
+ phy-supply = <&usb_pwr_en>;
};
&usb1 {
--
2.32.0
WARNING: multiple messages have this Message-ID (diff)
From: Anand Moon <linux.amoon@gmail.com>
To: linux-phy@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: Anand Moon <linux.amoon@gmail.com>,
Matt Corallo <oc2udbzfd@mattcorallo.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Rob Herring <robh+dt@kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Emiliano Ingrassia <ingrassia@epigenesys.com>,
devicetree@vger.kernel.org
Subject: [PATCHv1 1/3] ARM: dts: meson8b: odroidc1: Add usb phy power node
Date: Tue, 13 Jul 2021 05:52:13 +0000 [thread overview]
Message-ID: <20210713055227.1142-2-linux.amoon@gmail.com> (raw)
In-Reply-To: <20210713055227.1142-1-linux.amoon@gmail.com>
Add missing usb phy power node for phy mode fix below warning.
[ 1.253149] phy phy-c1108820.phy.0: Looking up phy-supply from device tree
[ 1.253166] phy phy-c1108820.phy.0: Looking up phy-supply property
in node /soc/cbus@c1100000/phy@8820 failed
Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host
controller on Odroid-C1/C1+ board)
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
previous version
[0] https://patchwork.kernel.org/project/linux-amlogic/patch/20190113181808.5768-1-linux.amoon@gmail.com
changes fix the vbus-suppy to phy-supply, drop enable usb0
# sudo cat /sys/kernel/debug/regulator/regulator_summary
USB_PWR 2 1 0 unknown 5000mV 0mA 5000mV 5000mV
phy-c1108820.phy.0-phy 2 0mA 0mV 0mV
---
arch/arm/boot/dts/meson8b-odroidc1.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index c440ef94e082..ced1ec1c4878 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -32,6 +32,25 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+ usb_pwr_en: regulator-usb-pwr-en {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
+
+ /*
+ * signal name from schematics: PWREN
+ */
+ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
leds {
compatible = "gpio-leds";
blue {
@@ -378,6 +397,7 @@ &uart_AO {
&usb1_phy {
status = "okay";
+ phy-supply = <&usb_pwr_en>;
};
&usb1 {
--
2.32.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Anand Moon <linux.amoon@gmail.com>
To: linux-phy@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: Anand Moon <linux.amoon@gmail.com>,
Matt Corallo <oc2udbzfd@mattcorallo.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Rob Herring <robh+dt@kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Emiliano Ingrassia <ingrassia@epigenesys.com>,
devicetree@vger.kernel.org
Subject: [PATCHv1 1/3] ARM: dts: meson8b: odroidc1: Add usb phy power node
Date: Tue, 13 Jul 2021 05:52:13 +0000 [thread overview]
Message-ID: <20210713055227.1142-2-linux.amoon@gmail.com> (raw)
In-Reply-To: <20210713055227.1142-1-linux.amoon@gmail.com>
Add missing usb phy power node for phy mode fix below warning.
[ 1.253149] phy phy-c1108820.phy.0: Looking up phy-supply from device tree
[ 1.253166] phy phy-c1108820.phy.0: Looking up phy-supply property
in node /soc/cbus@c1100000/phy@8820 failed
Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host
controller on Odroid-C1/C1+ board)
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
previous version
[0] https://patchwork.kernel.org/project/linux-amlogic/patch/20190113181808.5768-1-linux.amoon@gmail.com
changes fix the vbus-suppy to phy-supply, drop enable usb0
# sudo cat /sys/kernel/debug/regulator/regulator_summary
USB_PWR 2 1 0 unknown 5000mV 0mA 5000mV 5000mV
phy-c1108820.phy.0-phy 2 0mA 0mV 0mV
---
arch/arm/boot/dts/meson8b-odroidc1.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index c440ef94e082..ced1ec1c4878 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -32,6 +32,25 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+ usb_pwr_en: regulator-usb-pwr-en {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
+
+ /*
+ * signal name from schematics: PWREN
+ */
+ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
leds {
compatible = "gpio-leds";
blue {
@@ -378,6 +397,7 @@ &uart_AO {
&usb1_phy {
status = "okay";
+ phy-supply = <&usb_pwr_en>;
};
&usb1 {
--
2.32.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
WARNING: multiple messages have this Message-ID (diff)
From: Anand Moon <linux.amoon@gmail.com>
To: linux-phy@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: Anand Moon <linux.amoon@gmail.com>,
Matt Corallo <oc2udbzfd@mattcorallo.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Rob Herring <robh+dt@kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>,
Jerome Brunet <jbrunet@baylibre.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Emiliano Ingrassia <ingrassia@epigenesys.com>,
devicetree@vger.kernel.org
Subject: [PATCHv1 1/3] ARM: dts: meson8b: odroidc1: Add usb phy power node
Date: Tue, 13 Jul 2021 05:52:13 +0000 [thread overview]
Message-ID: <20210713055227.1142-2-linux.amoon@gmail.com> (raw)
In-Reply-To: <20210713055227.1142-1-linux.amoon@gmail.com>
Add missing usb phy power node for phy mode fix below warning.
[ 1.253149] phy phy-c1108820.phy.0: Looking up phy-supply from device tree
[ 1.253166] phy phy-c1108820.phy.0: Looking up phy-supply property
in node /soc/cbus@c1100000/phy@8820 failed
Fixes: 2eb79a4d15ff (ARM: dts: meson: enabling the USB Host
controller on Odroid-C1/C1+ board)
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
previous version
[0] https://patchwork.kernel.org/project/linux-amlogic/patch/20190113181808.5768-1-linux.amoon@gmail.com
changes fix the vbus-suppy to phy-supply, drop enable usb0
# sudo cat /sys/kernel/debug/regulator/regulator_summary
USB_PWR 2 1 0 unknown 5000mV 0mA 5000mV 5000mV
phy-c1108820.phy.0-phy 2 0mA 0mV 0mV
---
arch/arm/boot/dts/meson8b-odroidc1.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index c440ef94e082..ced1ec1c4878 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -32,6 +32,25 @@ emmc_pwrseq: emmc-pwrseq {
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+ usb_pwr_en: regulator-usb-pwr-en {
+ compatible = "regulator-fixed";
+
+ regulator-name = "USB_PWR";
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ /*
+ * signal name from schematics: USB_POWER
+ */
+ vin-supply = <&p5v0>;
+
+ /*
+ * signal name from schematics: PWREN
+ */
+ gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
leds {
compatible = "gpio-leds";
blue {
@@ -378,6 +397,7 @@ &uart_AO {
&usb1_phy {
status = "okay";
+ phy-supply = <&usb_pwr_en>;
};
&usb1 {
--
2.32.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
next prev parent reply other threads:[~2021-07-13 5:53 UTC|newest]
Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-07-13 5:52 [PATCHv1 0/3] Meson-8b and Meson-gxbb Fix some missing code Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon [this message]
2021-07-13 5:52 ` [PATCHv1 1/3] ARM: dts: meson8b: odroidc1: Add usb phy power node Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 15:05 ` Martin Blumenstingl
2021-07-13 15:05 ` Martin Blumenstingl
2021-07-13 15:05 ` Martin Blumenstingl
2021-07-13 15:05 ` Martin Blumenstingl
2021-07-13 18:44 ` Anand Moon
2021-07-13 18:44 ` Anand Moon
2021-07-13 18:44 ` Anand Moon
2021-07-13 18:44 ` Anand Moon
2021-07-13 20:35 ` Martin Blumenstingl
2021-07-13 20:35 ` Martin Blumenstingl
2021-07-13 20:35 ` Martin Blumenstingl
2021-07-13 20:35 ` Martin Blumenstingl
2021-07-14 11:59 ` Anand Moon
2021-07-14 11:59 ` Anand Moon
2021-07-14 11:59 ` Anand Moon
2021-07-14 11:59 ` Anand Moon
2021-07-14 17:25 ` Anand Moon
2021-07-14 17:25 ` Anand Moon
2021-07-14 17:25 ` Anand Moon
2021-07-14 17:25 ` Anand Moon
2021-07-14 23:30 ` Martin Blumenstingl
2021-07-14 23:30 ` Martin Blumenstingl
2021-07-14 23:30 ` Martin Blumenstingl
2021-07-14 23:30 ` Martin Blumenstingl
2021-07-15 10:24 ` Anand Moon
2021-07-15 10:24 ` Anand Moon
2021-07-15 10:24 ` Anand Moon
2021-07-15 10:24 ` Anand Moon
2021-07-13 5:52 ` [PATCHv1 2/3] phy: amlogic: meson8b-usb2: Power off the PHY by putting it into reset mode Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 15:10 ` Martin Blumenstingl
2021-07-13 15:10 ` Martin Blumenstingl
2021-07-13 15:10 ` Martin Blumenstingl
2021-07-13 15:10 ` Martin Blumenstingl
2021-07-13 5:52 ` [PATCHv1 3/3] phy: amlogic: meson8b-usb2: don't log an error on -EPROBE_DEFER Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
2021-07-13 5:52 ` Anand Moon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210713055227.1142-2-linux.amoon@gmail.com \
--to=linux.amoon@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=ingrassia@epigenesys.com \
--cc=jbrunet@baylibre.com \
--cc=khilman@baylibre.com \
--cc=kishon@ti.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=narmstrong@baylibre.com \
--cc=oc2udbzfd@mattcorallo.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.