From: Suman Anna <s-anna@ti.com> To: Tony Lindgren <tony@atomide.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com>, Kishon Vijay Abraham I <kishon@ti.com>, Lokesh Vutla <lokeshvutla@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, <linux-omap@vger.kernel.org>, <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, Suman Anna <s-anna@ti.com> Subject: [PATCH 11/11] ARM: dts: am57xx: Add PRUSS MDIO controller nodes Date: Thu, 29 Jul 2021 17:46:21 -0500 [thread overview] Message-ID: <20210729224621.2295-12-s-anna@ti.com> (raw) In-Reply-To: <20210729224621.2295-1-s-anna@ti.com> The PRUSSs on AM57xx SoCs contain an MDIO controller that can be used to control external PHYs associated with the Industrial Ethernet peripherals within each PRUSS. The MDIO module used within the PRU-ICSS is an instance of the MDIO Controller used in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as the regular MDIO node. The nodes are added in the common am57-pruss.dtsi file and enabled by default, but are disabled in all the existing AM57xx board dts files. These nodes need pinctrl lines, and so should be enabled only on boards where they are actually wired and pinned out for PRUSS Ethernet. Any new board dts file should disable these if they are not sure. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> --- arch/arm/boot/dts/am57-pruss.dtsi | 20 +++++++++++++++++++ arch/arm/boot/dts/am571x-idk.dts | 8 ++++++++ arch/arm/boot/dts/am572x-idk.dts | 8 ++++++++ arch/arm/boot/dts/am574x-idk.dts | 8 ++++++++ .../boot/dts/am57xx-beagle-x15-common.dtsi | 8 ++++++++ arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 8 ++++++++ 6 files changed, 60 insertions(+) diff --git a/arch/arm/boot/dts/am57-pruss.dtsi b/arch/arm/boot/dts/am57-pruss.dtsi index 494d56830b34..46c5383f0eee 100644 --- a/arch/arm/boot/dts/am57-pruss.dtsi +++ b/arch/arm/boot/dts/am57-pruss.dtsi @@ -102,6 +102,16 @@ pru1_1: pru@38000 { reg-names = "iram", "control", "debug"; firmware-name = "am57xx-pru1_1-fw"; }; + + pruss1_mdio: mdio@32400 { + compatible = "ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&dpll_gmac_h13x2_ck>; + clock-names = "fck"; + bus_freq = <1000000>; + reg = <0x32400 0x90>; + }; }; }; @@ -201,6 +211,16 @@ pru2_1: pru@38000 { reg-names = "iram", "control", "debug"; firmware-name = "am57xx-pru2_1-fw"; }; + + pruss2_mdio: mdio@32400 { + compatible = "ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&dpll_gmac_h13x2_ck>; + clock-names = "fck"; + bus_freq = <1000000>; + reg = <0x32400 0x90>; + }; }; }; }; diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index e81078c2d00d..48425020281a 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -208,3 +208,11 @@ &mmc2 { pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 6504265f3f7e..94a738cb0a4d 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -27,3 +27,11 @@ &mmc2 { pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index 1b8f3a28af05..c4bf9cb2c9dc 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -43,3 +43,11 @@ &m_can0 { &emif1 { status = "okay"; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 6b82ecf803c5..994e69ab38d7 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -637,3 +637,11 @@ &dsp2 { status = "okay"; memory-region = <&dsp2_memory_region>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index aed81568a297..2e94f32d9dfc 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -618,3 +618,11 @@ &gpio2_target { status = "okay"; ti,no-reset-on-init; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; -- 2.32.0
WARNING: multiple messages have this Message-ID (diff)
From: Suman Anna <s-anna@ti.com> To: Tony Lindgren <tony@atomide.com> Cc: devicetree@vger.kernel.org, Grygorii Strashko <grygorii.strashko@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, Lokesh Vutla <lokeshvutla@ti.com>, Kishon Vijay Abraham I <kishon@ti.com>, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org Subject: [PATCH 11/11] ARM: dts: am57xx: Add PRUSS MDIO controller nodes Date: Thu, 29 Jul 2021 17:46:21 -0500 [thread overview] Message-ID: <20210729224621.2295-12-s-anna@ti.com> (raw) In-Reply-To: <20210729224621.2295-1-s-anna@ti.com> The PRUSSs on AM57xx SoCs contain an MDIO controller that can be used to control external PHYs associated with the Industrial Ethernet peripherals within each PRUSS. The MDIO module used within the PRU-ICSS is an instance of the MDIO Controller used in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as the regular MDIO node. The nodes are added in the common am57-pruss.dtsi file and enabled by default, but are disabled in all the existing AM57xx board dts files. These nodes need pinctrl lines, and so should be enabled only on boards where they are actually wired and pinned out for PRUSS Ethernet. Any new board dts file should disable these if they are not sure. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> --- arch/arm/boot/dts/am57-pruss.dtsi | 20 +++++++++++++++++++ arch/arm/boot/dts/am571x-idk.dts | 8 ++++++++ arch/arm/boot/dts/am572x-idk.dts | 8 ++++++++ arch/arm/boot/dts/am574x-idk.dts | 8 ++++++++ .../boot/dts/am57xx-beagle-x15-common.dtsi | 8 ++++++++ arch/arm/boot/dts/am57xx-cl-som-am57x.dts | 8 ++++++++ 6 files changed, 60 insertions(+) diff --git a/arch/arm/boot/dts/am57-pruss.dtsi b/arch/arm/boot/dts/am57-pruss.dtsi index 494d56830b34..46c5383f0eee 100644 --- a/arch/arm/boot/dts/am57-pruss.dtsi +++ b/arch/arm/boot/dts/am57-pruss.dtsi @@ -102,6 +102,16 @@ pru1_1: pru@38000 { reg-names = "iram", "control", "debug"; firmware-name = "am57xx-pru1_1-fw"; }; + + pruss1_mdio: mdio@32400 { + compatible = "ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&dpll_gmac_h13x2_ck>; + clock-names = "fck"; + bus_freq = <1000000>; + reg = <0x32400 0x90>; + }; }; }; @@ -201,6 +211,16 @@ pru2_1: pru@38000 { reg-names = "iram", "control", "debug"; firmware-name = "am57xx-pru2_1-fw"; }; + + pruss2_mdio: mdio@32400 { + compatible = "ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&dpll_gmac_h13x2_ck>; + clock-names = "fck"; + bus_freq = <1000000>; + reg = <0x32400 0x90>; + }; }; }; }; diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts index e81078c2d00d..48425020281a 100644 --- a/arch/arm/boot/dts/am571x-idk.dts +++ b/arch/arm/boot/dts/am571x-idk.dts @@ -208,3 +208,11 @@ &mmc2 { pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts index 6504265f3f7e..94a738cb0a4d 100644 --- a/arch/arm/boot/dts/am572x-idk.dts +++ b/arch/arm/boot/dts/am572x-idk.dts @@ -27,3 +27,11 @@ &mmc2 { pinctrl-1 = <&mmc2_pins_hs>; pinctrl-2 = <&mmc2_pins_ddr_rev20>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index 1b8f3a28af05..c4bf9cb2c9dc 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -43,3 +43,11 @@ &m_can0 { &emif1 { status = "okay"; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi index 6b82ecf803c5..994e69ab38d7 100644 --- a/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi +++ b/arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi @@ -637,3 +637,11 @@ &dsp2 { status = "okay"; memory-region = <&dsp2_memory_region>; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts index aed81568a297..2e94f32d9dfc 100644 --- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts +++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts @@ -618,3 +618,11 @@ &gpio2_target { status = "okay"; ti,no-reset-on-init; }; + +&pruss1_mdio { + status = "disabled"; +}; + +&pruss2_mdio { + status = "disabled"; +}; -- 2.32.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-07-29 22:46 UTC|newest] Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-07-29 22:46 [PATCH 00/11] Add PRU-ICSS nodes on AM335x, AM437x & AM57xx SoCs Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 01/11] ARM: dts: am33xx-l4: Add PRUSS node Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 02/11] ARM: dts: am33xx-l4: Add PRUSS MDIO controller node Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 03/11] ARM: dts: am335x-bone-common: Enable PRU-ICSS node Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 04/11] ARM: dts: am335x-evm: Enable PRU-ICSS module Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 05/11] ARM: dts: am335x-evmsk: " Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 06/11] ARM: dts: am335x-icev2: " Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 07/11] ARM: dts: am4372: Add the PRU-ICSS1 DT node Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 08/11] ARM: dts: am4372: Add the PRU-ICSS0 " Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 09/11] ARM: dts: am4372: Add PRUSS MDIO controller node Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` [PATCH 10/11] ARM: dts: am57xx: Add PRU-ICSS nodes Suman Anna 2021-07-29 22:46 ` Suman Anna 2021-07-29 22:46 ` Suman Anna [this message] 2021-07-29 22:46 ` [PATCH 11/11] ARM: dts: am57xx: Add PRUSS MDIO controller nodes Suman Anna 2021-08-03 12:53 ` [PATCH 00/11] Add PRU-ICSS nodes on AM335x, AM437x & AM57xx SoCs Tony Lindgren 2021-08-03 12:53 ` Tony Lindgren
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210729224621.2295-12-s-anna@ti.com \ --to=s-anna@ti.com \ --cc=devicetree@vger.kernel.org \ --cc=grygorii.strashko@ti.com \ --cc=kishon@ti.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-omap@vger.kernel.org \ --cc=lokeshvutla@ti.com \ --cc=tony@atomide.com \ --cc=vigneshr@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.