All of lore.kernel.org
 help / color / mirror / Atom feed
From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
	Kevin Hilman <khilman@baylibre.com>,
	linux-amlogic@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 3/3] arm64: meson: update SDIO in dts for JetHub D1
Date: Fri, 25 Mar 2022 19:55:01 +0300	[thread overview]
Message-ID: <20220325165501.81551-4-adeep@lexina.in> (raw)
In-Reply-To: <20220325165501.81551-1-adeep@lexina.in>

Fix the dts to match board's reference design:
- update vddio_boot regulator to 3.3v (Wi-Fi SDIO module)
- add vccq_1v8 regulator with 1.8v for eMMC SDIO

In the first revision of JetHub D1 the vccq_1v8 regulator was 3.3v.
All installed eMMC modules were tested to work in HS200 mode at 3.3v
supply voltage. In the next revisions of the board eMMC will be
powered with 1.8v according to the standard.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 .../dts/amlogic/meson-axg-jethome-jethub-j100.dts | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index 66c1eeba8f48..bc00d672a357 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -81,12 +81,22 @@ vddio_ao18: regulator-vddio_ao18 {
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vccq_1v8: regulator-vccq_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCQ_1V8";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		vin-supply = <&vddao_3v3>;
 		regulator-always-on;
 	};
 
+
 	usb_pwr: regulator-usb_pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "USB_PWR";
@@ -248,8 +258,7 @@ &sd_emmc_b {
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr104;
-	max-frequency = <200000000>;
+	max-frequency = <50000000>;
 	non-removable;
 	disable-wp;
 
@@ -282,7 +291,7 @@ &sd_emmc_c {
 	mmc-pwrseq = <&emmc_pwrseq>;
 
 	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&vddio_boot>;
+	vqmmc-supply = <&vccq_1v8>;
 };
 
 /* UART Bluetooth */
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

WARNING: multiple messages have this Message-ID (diff)
From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
	Kevin Hilman <khilman@baylibre.com>,
	linux-amlogic@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 3/3] arm64: meson: update SDIO in dts for JetHub D1
Date: Fri, 25 Mar 2022 19:55:01 +0300	[thread overview]
Message-ID: <20220325165501.81551-4-adeep@lexina.in> (raw)
In-Reply-To: <20220325165501.81551-1-adeep@lexina.in>

Fix the dts to match board's reference design:
- update vddio_boot regulator to 3.3v (Wi-Fi SDIO module)
- add vccq_1v8 regulator with 1.8v for eMMC SDIO

In the first revision of JetHub D1 the vccq_1v8 regulator was 3.3v.
All installed eMMC modules were tested to work in HS200 mode at 3.3v
supply voltage. In the next revisions of the board eMMC will be
powered with 1.8v according to the standard.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 .../dts/amlogic/meson-axg-jethome-jethub-j100.dts | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index 66c1eeba8f48..bc00d672a357 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -81,12 +81,22 @@ vddio_ao18: regulator-vddio_ao18 {
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vccq_1v8: regulator-vccq_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCQ_1V8";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		vin-supply = <&vddao_3v3>;
 		regulator-always-on;
 	};
 
+
 	usb_pwr: regulator-usb_pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "USB_PWR";
@@ -248,8 +258,7 @@ &sd_emmc_b {
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr104;
-	max-frequency = <200000000>;
+	max-frequency = <50000000>;
 	non-removable;
 	disable-wp;
 
@@ -282,7 +291,7 @@ &sd_emmc_c {
 	mmc-pwrseq = <&emmc_pwrseq>;
 
 	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&vddio_boot>;
+	vqmmc-supply = <&vccq_1v8>;
 };
 
 /* UART Bluetooth */
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Vyacheslav Bocharov <adeep@lexina.in>
To: Neil Armstrong <narmstrong@baylibre.com>,
	Kevin Hilman <khilman@baylibre.com>,
	linux-amlogic@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 3/3] arm64: meson: update SDIO in dts for JetHub D1
Date: Fri, 25 Mar 2022 19:55:01 +0300	[thread overview]
Message-ID: <20220325165501.81551-4-adeep@lexina.in> (raw)
In-Reply-To: <20220325165501.81551-1-adeep@lexina.in>

Fix the dts to match board's reference design:
- update vddio_boot regulator to 3.3v (Wi-Fi SDIO module)
- add vccq_1v8 regulator with 1.8v for eMMC SDIO

In the first revision of JetHub D1 the vccq_1v8 regulator was 3.3v.
All installed eMMC modules were tested to work in HS200 mode at 3.3v
supply voltage. In the next revisions of the board eMMC will be
powered with 1.8v according to the standard.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 .../dts/amlogic/meson-axg-jethome-jethub-j100.dts | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index 66c1eeba8f48..bc00d672a357 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -81,12 +81,22 @@ vddio_ao18: regulator-vddio_ao18 {
 	vddio_boot: regulator-vddio_boot {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vccq_1v8: regulator-vccq_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCQ_1V8";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		vin-supply = <&vddao_3v3>;
 		regulator-always-on;
 	};
 
+
 	usb_pwr: regulator-usb_pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "USB_PWR";
@@ -248,8 +258,7 @@ &sd_emmc_b {
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr104;
-	max-frequency = <200000000>;
+	max-frequency = <50000000>;
 	non-removable;
 	disable-wp;
 
@@ -282,7 +291,7 @@ &sd_emmc_c {
 	mmc-pwrseq = <&emmc_pwrseq>;
 
 	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&vddio_boot>;
+	vqmmc-supply = <&vccq_1v8>;
 };
 
 /* UART Bluetooth */
-- 
2.30.2


  parent reply	other threads:[~2022-03-25 16:55 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-03-25 16:54 [PATCH 0/3] arm64: meson: update dts for JetHub devices Vyacheslav Bocharov
2022-03-25 16:54 ` Vyacheslav Bocharov
2022-03-25 16:54 ` Vyacheslav Bocharov
2022-03-25 16:54 ` [PATCH 1/3] arm64: meson: add dts bluetooth node for JetHub H1 Vyacheslav Bocharov
2022-03-25 16:54   ` Vyacheslav Bocharov
2022-03-25 16:54   ` Vyacheslav Bocharov
2022-03-25 17:32   ` Neil Armstrong
2022-03-25 17:32     ` Neil Armstrong
2022-03-25 17:32     ` Neil Armstrong
2022-03-25 16:55 ` [PATCH 2/3] arm64: meson: dts: update serial alias in dts for JetHub D1 Vyacheslav Bocharov
2022-03-25 16:55   ` Vyacheslav Bocharov
2022-03-25 16:55   ` Vyacheslav Bocharov
2022-03-25 16:55 ` Vyacheslav Bocharov [this message]
2022-03-25 16:55   ` [PATCH 3/3] arm64: meson: update SDIO " Vyacheslav Bocharov
2022-03-25 16:55   ` Vyacheslav Bocharov
2022-03-25 17:33   ` Neil Armstrong
2022-03-25 17:33     ` Neil Armstrong
2022-03-25 17:33     ` Neil Armstrong
2022-03-25 17:34 ` [PATCH 0/3] arm64: meson: update dts for JetHub devices Neil Armstrong
2022-03-25 17:34   ` Neil Armstrong
2022-03-25 17:34   ` Neil Armstrong
2022-03-26  7:42   ` Vyacheslav
2022-03-26  7:42     ` Vyacheslav
2022-03-26  7:42     ` Vyacheslav

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220325165501.81551-4-adeep@lexina.in \
    --to=adeep@lexina.in \
    --cc=devicetree@vger.kernel.org \
    --cc=khilman@baylibre.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=narmstrong@baylibre.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.