[PATCH v4 6/7] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node

From: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
To: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
	linux-media@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	Samuel Holland <samuel@sholland.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	Frank Rowand <frowand.list@gmail.com>,
	Maxime Ripard <mripard@kernel.org>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
	Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Subject: [PATCH v4 6/7] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node
Date: Wed, 25 May 2022 20:58:52 +0200	[thread overview]
Message-ID: <20220525185853.695931-7-paul.kocialkowski@bootlin.com> (raw)
In-Reply-To: <20220525185853.695931-1-paul.kocialkowski@bootlin.com>

MIPI CSI-2 is supported on the A83T with a dedicated controller that
covers both the protocol and D-PHY. It can be connected to the CSI
interface as a V4L2 subdev through the fwnode graph.

This is not done by default since connecting the bridge without a
subdev attached to it will cause a failure on the CSI driver.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
 arch/arm/boot/dts/sun8i-a83t.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index 82fdb04122ca..ecf9f3b2c0c0 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -1064,6 +1064,32 @@ csi: camera@1cb0000 {
 			status = "disabled";
 		};
 
+		mipi_csi2: csi@1cb1000 {
+			compatible = "allwinner,sun8i-a83t-mipi-csi2";
+			reg = <0x01cb1000 0x1000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI_SCLK>,
+				 <&ccu CLK_MIPI_CSI>,
+				 <&ccu CLK_CSI_MISC>;
+			clock-names = "bus", "mod", "mipi", "misc";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi_csi2_in: port@0 {
+					reg = <0>;
+				};
+
+				mipi_csi2_out: port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
 		hdmi: hdmi@1ee0000 {
 			compatible = "allwinner,sun8i-a83t-dw-hdmi";
 			reg = <0x01ee0000 0x10000>;
-- 
2.36.1

