Re: [PATCH v2 1/6] arm64: dts: ls2080a-qds: add mdio mux nodes from on-board FPGA

From: Shawn Guo <shawnguo@kernel.org>
To: Li Yang <leoyang.li@nxp.com>
Cc: devicetree@vger.kernel.org, robh+dt@kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 1/6] arm64: dts: ls2080a-qds: add mdio mux nodes from on-board FPGA
Date: Mon, 22 Aug 2022 11:44:46 +0800	[thread overview]
Message-ID: <20220822034446.GS149610@dragon> (raw)
In-Reply-To: <20220817204357.21753-2-leoyang.li@nxp.com>

On Wed, Aug 17, 2022 at 03:43:52PM -0500, Li Yang wrote:
> Add mmio mdio mux nodes from the on-board FPGA.
> 
> Signed-off-by: Li Yang <leoyang.li@nxp.com>
> ---
>  .../boot/dts/freescale/fsl-ls2080a-qds.dts    | 69 +++++++++++++++++++
>  1 file changed, 69 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> index f6c3ee78ace0..ef79c9a78f89 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-qds.dts
> @@ -23,3 +23,72 @@ chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
>  };
> +
> +/* Update DPMAC connections to external PHYs, under SerDes 0x2a_0x49. */
> +&dpmac9 {
> +	phy-handle = <&mdio0_phy12>;
> +	phy-connection-type = "sgmii";
> +};
> +
> +&dpmac10 {
> +	phy-handle = <&mdio0_phy13>;
> +	phy-connection-type = "sgmii";
> +};
> +
> +&dpmac11 {
> +	phy-handle = <&mdio0_phy14>;
> +	phy-connection-type = "sgmii";
> +};
> +
> +&dpmac12 {
> +	phy-handle = <&mdio0_phy15>;
> +	phy-connection-type = "sgmii";
> +};
> +
> +&ifc {
> +	boardctrl: board-control@3,0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "fsl,tetra-fpga", "fsl,fpga-qixis", "simple-mfd";
> +		reg = <3 0 0x300>;
> +		ranges = <0 3 0 0x300>;
> +
> +		mdio-mux-emi1@54 {
> +			compatible = "mdio-mux-mmioreg", "mdio-mux";
> +			mdio-parent-bus = <&emdio1>;
> +			reg = <0x54 1>;		/* BRDCFG4 */
> +			mux-mask = <0xe0>;	/* EMI1_MDIO */
> +

Unnecessary newline.

> +			#address-cells=<1>;
> +			#size-cells = <0>;
> +
> +			/* Child MDIO buses, one for each riser card:
> +			 * reg = 0x0, 0x20, 0x40, 0x60, 0x80, 0xa0.
> +			 * VSC8234 PHYs on the riser cards.
> +			 */
> +
> +			mdio_mux3: mdio@60 {
> +				reg = <0x60>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				mdio0_phy12: mdio_phy0@1c {

Hyphen is recommended in node name.

Shawn

> +					reg = <0x1c>;
> +				};
> +
> +				mdio0_phy13: mdio_phy1@1d {
> +					reg = <0x1d>;
> +				};
> +
> +				mdio0_phy14: mdio_phy2@1e {
> +					reg = <0x1e>;
> +				};
> +
> +				mdio0_phy15: mdio_phy3@1f {
> +					reg = <0x1f>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> -- 
> 2.37.1
> 