From: Richard Acayan <mailingradian@gmail.com>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org
Cc: Odelu Kukatla <quic_okukatla@quicinc.com>,
Luca Weiss <luca@z3ntu.xyz>,
Richard Acayan <mailingradian@gmail.com>
Subject: [PATCH v4 2/2] arm64: dts: qcom: sdm670: add opps for peripherals
Date: Tue, 31 Jan 2023 20:00:20 -0500 [thread overview]
Message-ID: <20230201010020.84586-3-mailingradian@gmail.com> (raw)
In-Reply-To: <20230201010020.84586-1-mailingradian@gmail.com>
The interconnects are now in place. Add Operating Performance Points for
them to allow the kernel to properly manage them.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
---
arch/arm64/boot/dts/qcom/sdm670.dtsi | 109 +++++++++++++++++++++++++++
1 file changed, 109 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm670.dtsi b/arch/arm64/boot/dts/qcom/sdm670.dtsi
index 02f14692dd9d..c5f839dd1c6e 100644
--- a/arch/arm64/boot/dts/qcom/sdm670.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm670.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,sdm670-rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/phy/phy-qcom-qusb2.h>
#include <dt-bindings/power/qcom-rpmpd.h>
@@ -430,6 +431,10 @@ sdhc_1: mmc@7c4000 {
<&gcc GCC_SDCC1_ICE_CORE_CLK>,
<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>;
clock-names = "iface", "core", "xo", "ice", "bus";
+ interconnects = <&aggre1_noc MASTER_EMMC 0 &aggre1_noc SLAVE_A1NOC_SNOC 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_EMMC_CFG 0>;
+ interconnect-names = "sdhc-ddr", "cpu-sdhc";
+ operating-points-v2 = <&sdhc1_opp_table>;
iommus = <&apps_smmu 0x140 0xf>;
@@ -442,6 +447,38 @@ sdhc_1: mmc@7c4000 {
non-removable;
status = "disabled";
+
+ sdhc1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-20000000 {
+ opp-hz = /bits/ 64 <20000000>;
+ required-opps = <&rpmhpd_opp_min_svs>;
+ opp-peak-kBps = <80000 80000>;
+ opp-avg-kBps = <52286 80000>;
+ };
+
+ opp-50000000 {
+ opp-hz = /bits/ 64 <50000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ opp-peak-kBps = <200000 100000>;
+ opp-avg-kBps = <130718 100000>;
+ };
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ opp-peak-kBps = <200000 130000>;
+ opp-avg-kBps = <130718 130000>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ opp-peak-kBps = <4096000 4096000>;
+ opp-avg-kBps = <1338562 1338562>;
+ };
+ };
};
gpi_dma0: dma-controller@800000 {
@@ -477,6 +514,8 @@ qupv3_id_0: geniqup@8c0000 {
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>;
+ interconnect-names = "qup-core";
status = "disabled";
i2c0: i2c@880000 {
@@ -490,6 +529,10 @@ i2c0: i2c@880000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
<&gpi_dma0 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -507,6 +550,10 @@ i2c1: i2c@884000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
<&gpi_dma0 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -524,6 +571,10 @@ i2c2: i2c@888000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
<&gpi_dma0 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -541,6 +592,10 @@ i2c3: i2c@88c000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
<&gpi_dma0 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -558,6 +613,10 @@ i2c4: i2c@890000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
<&gpi_dma0 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -575,6 +634,10 @@ i2c5: i2c@894000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
<&gpi_dma0 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -592,6 +655,10 @@ i2c6: i2c@898000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
<&gpi_dma0 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -609,6 +676,10 @@ i2c7: i2c@89c000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre1_noc MASTER_BLSP_1 0 &config_noc SLAVE_BLSP_1 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_1 0>,
+ <&aggre1_noc MASTER_BLSP_1 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
<&gpi_dma0 1 7 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -649,6 +720,8 @@ qupv3_id_1: geniqup@ac0000 {
#address-cells = <2>;
#size-cells = <2>;
ranges;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>;
+ interconnect-names = "qup-core";
status = "disabled";
i2c8: i2c@a80000 {
@@ -662,6 +735,10 @@ i2c8: i2c@a80000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
<&gpi_dma1 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -679,6 +756,10 @@ i2c9: i2c@a84000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
<&gpi_dma1 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -696,6 +777,10 @@ i2c10: i2c@a88000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
<&gpi_dma1 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -713,6 +798,10 @@ i2c11: i2c@a8c000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
<&gpi_dma1 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -730,6 +819,10 @@ i2c12: i2c@a90000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
<&gpi_dma1 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -747,6 +840,10 @@ i2c13: i2c@a94000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
<&gpi_dma1 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -764,6 +861,10 @@ i2c14: i2c@a98000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
<&gpi_dma1 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -781,6 +882,10 @@ i2c15: i2c@a9c000 {
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&rpmhpd SDM670_CX>;
+ interconnects = <&aggre2_noc MASTER_BLSP_2 0 &config_noc SLAVE_BLSP_2 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_BLSP_2 0>,
+ <&aggre2_noc MASTER_BLSP_2 0 &mem_noc SLAVE_EBI_CH0 0>;
+ interconnect-names = "qup-core", "qup-config", "qup-memory";
dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
<&gpi_dma1 1 7 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
@@ -1028,6 +1133,10 @@ usb_1: usb@a6f8800 {
resets = <&gcc GCC_USB30_PRIM_BCR>;
+ interconnects = <&aggre2_noc MASTER_USB3 0 &mem_noc SLAVE_EBI_CH0 0>,
+ <&gladiator_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3 0>;
+ interconnect-names = "usb-ddr", "apps-usb";
+
status = "disabled";
usb_1_dwc3: usb@a600000 {
--
2.39.1
next prev parent reply other threads:[~2023-02-01 1:00 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-01 1:00 [PATCH v4 0/2] SDM670 Interconnects (now with dts patches only) Richard Acayan
2023-02-01 1:00 ` [PATCH v4 1/2] arm64: dts: qcom: sdm670: add interconnects Richard Acayan
2023-02-01 1:00 ` Richard Acayan [this message]
2023-02-01 18:51 ` [PATCH v4 2/2] arm64: dts: qcom: sdm670: add opps for peripherals Konrad Dybcio
2023-02-09 4:23 ` [PATCH v4 0/2] SDM670 Interconnects (now with dts patches only) Bjorn Andersson
2023-03-15 23:35 ` (subset) " Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230201010020.84586-3-mailingradian@gmail.com \
--to=mailingradian@gmail.com \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=luca@z3ntu.xyz \
--cc=quic_okukatla@quicinc.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.