From: Varshini Rajendran <varshini.rajendran@microchip.com>
To: <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<conor+dt@kernel.org>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>, <claudiu.beznea@microchip.com>,
<mturquette@baylibre.com>, <sboyd@kernel.org>,
<herbert@gondor.apana.org.au>, <davem@davemloft.net>,
<vkoul@kernel.org>, <tglx@linutronix.de>, <maz@kernel.org>,
<lee@kernel.org>, <ulf.hansson@linaro.org>,
<tudor.ambarus@linaro.org>, <miquel.raynal@bootlin.com>,
<richard@nod.at>, <vigneshr@ti.com>, <edumazet@google.com>,
<kuba@kernel.org>, <pabeni@redhat.com>,
<linus.walleij@linaro.org>, <p.zabel@pengutronix.de>,
<olivia@selenic.com>, <a.zummo@towertech.it>,
<radu_nicolae.pirea@upb.ro>, <richard.genoud@gmail.com>,
<gregkh@linuxfoundation.org>, <lgirdwood@gmail.com>,
<broonie@kernel.org>, <wim@linux-watchdog.org>,
<linux@roeck-us.net>, <arnd@arndb.de>, <olof@lixom.net>,
<soc@kernel.org>, <linux@armlinux.org.uk>, <sre@kernel.org>,
<jerry.ray@microchip.com>, <horatiu.vultur@microchip.com>,
<durai.manickamkr@microchip.com>,
<varshini.rajendran@microchip.com>, <andrew@lunn.ch>,
<alain.volmat@foss.st.com>, <neil.armstrong@linaro.org>,
<mihai.sain@microchip.com>, <eugen.hristev@collabora.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-clk@vger.kernel.org>,
<linux-crypto@vger.kernel.org>, <dmaengine@vger.kernel.org>,
<linux-i2c@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
<linux-mtd@lists.infradead.org>, <netdev@vger.kernel.org>,
<linux-gpio@vger.kernel.org>, <linux-rtc@vger.kernel.org>,
<linux-spi@vger.kernel.org>, <linux-serial@vger.kernel.org>,
<alsa-devel@alsa-project.org>, <linux-usb@vger.kernel.org>,
<linux-watchdog@vger.kernel.org>, <linux-pm@vger.kernel.org>
Cc: <Hari.PrasathGE@microchip.com>, <cristian.birsan@microchip.com>,
<balamanikandan.gunasundar@microchip.com>,
<manikandan.m@microchip.com>, <dharma.b@microchip.com>,
<nayabbasha.sayed@microchip.com>, <balakrishnan.s@microchip.com>
Subject: [PATCH v2 43/45] ARM: dts: at91: sam9x7: add device tree for SoC
Date: Sat, 24 Jun 2023 02:00:54 +0530 [thread overview]
Message-ID: <20230623203056.689705-44-varshini.rajendran@microchip.com> (raw)
In-Reply-To: <20230623203056.689705-1-varshini.rajendran@microchip.com>
Add device tree file for SAM9X7 SoC family.
Co-developed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
---
arch/arm/boot/dts/sam9x7.dtsi | 1237 +++++++++++++++++++++++++++++++++
1 file changed, 1237 insertions(+)
create mode 100644 arch/arm/boot/dts/sam9x7.dtsi
diff --git a/arch/arm/boot/dts/sam9x7.dtsi b/arch/arm/boot/dts/sam9x7.dtsi
new file mode 100644
index 000000000000..535a55f13dd0
--- /dev/null
+++ b/arch/arm/boot/dts/sam9x7.dtsi
@@ -0,0 +1,1237 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Microchip SAM9X7 SoC";
+ compatible = "microchip,sam9x7";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ reg = <0>;
+ };
+ };
+
+ clocks {
+ slow_xtal: clock-slowxtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ main_xtal: clock-mainxtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+ };
+
+ sram: sram@300000 {
+ compatible = "mmio-sram";
+ reg = <0x300000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x300000 0x10000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usb0: gadget@500000 {
+ compatible = "microchip,sam9x7-udc", "microchip,sam9x60-udc";
+ reg = <0x500000 0x100000>,
+ <0xf803c000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ clock-names = "pclk", "hclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ assigned-clock-rates = <480000000>;
+ status = "disabled";
+ };
+
+ ohci0: usb@600000 {
+ compatible = "microchip,sam9x7-ohci", "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x600000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+
+ ehci0: usb@700000 {
+ compatible = "microchip,sam9x7-ehci", "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x700000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
+ clock-names = "usb_clk", "ehci_clk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ assigned-clock-rates = <480000000>;
+ status = "disabled";
+ };
+
+ sdmmc0: sdio-host@80000000 {
+ compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+ reg = <0x80000000 0x300>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+ clock-names = "hclock", "multclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+ assigned-clock-rates = <100000000>;
+ status = "disabled";
+ };
+
+ sdmmc1: sdio-host@90000000 {
+ compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+ reg = <0x90000000 0x300>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+ clock-names = "hclock", "multclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+ assigned-clock-rates = <100000000>;
+ status = "disabled";
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ flx4: flexcom@f0000000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0000000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0000000 0x800>;
+ status = "disabled";
+
+ uart4: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi4: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx5: flexcom@f0004000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0004000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0004000 0x800>;
+ status = "disabled";
+
+ uart5: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi5: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ dma0: dma-controller@f0008000 {
+ compatible = "microchip,sam9x7-dma", "microchip,sam9x60-dma", "atmel,sama5d4-dma";
+ reg = <0xf0008000 0x1000>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <1>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+ clock-names = "dma_clk";
+ status = "disabled";
+ };
+
+ ssc: ssc@f0010000 {
+ compatible = "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(38))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(39))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ i2s: i2s@f001c000 {
+ compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
+ reg = <0xf001c000 0x100>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+ clock-names = "pclk", "gclk";
+ status = "disabled";
+ };
+
+ flx11: flexcom@f0020000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0020000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0020000 0x800>;
+ status = "disabled";
+
+ uart11: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx12: flexcom@f0024000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0024000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0024000 0x800>;
+ status = "disabled";
+
+ uart12: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ pit64b0: timer@f0028000 {
+ compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+ reg = <0xf0028000 0x100>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+ clock-names = "pclk", "gclk";
+ };
+
+ sha: crypto@f002c000 {
+ compatible = "microchip,sam9x7-sha", "atmel,at91sam9g46-sha";
+ reg = <0xf002c000 0x100>;
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(34))>;
+ dma-names = "tx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+ clock-names = "sha_clk";
+ };
+
+ trng: rng@f0030000 {
+ compatible = "microchip,sam9x7-trng", "microchip,sam9x60-trng";
+ reg = <0xf0030000 0x100>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+ status = "disabled";
+ };
+
+ aes: crypto@f0034000 {
+ compatible = "microchip,sam9x7-aes", "atmel,at91sam9g46-aes";
+ reg = <0xf0034000 0x100>;
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(32))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(33))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+ clock-names = "aes_clk";
+ };
+
+ tdes: crypto@f0038000 {
+ compatible = "microchip,sam9x7-tdes", "atmel,at91sam9g46-tdes";
+ reg = <0xf0038000 0x100>;
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(31))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(30))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+ clock-names = "tdes_clk";
+ };
+
+ classd: classd@f003c000 {
+ compatible = "microchip,sam9x7-classd", "atmel,sama5d2-classd";
+ reg = <0xf003c000 0x100>;
+ interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(35))>;
+ dma-names = "tx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+ clock-names = "pclk", "gclk";
+ status = "disabled";
+ };
+
+ pit64b1: timer@f0040000 {
+ compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+ reg = <0xf0040000 0x100>;
+ interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+ clock-names = "pclk", "gclk";
+ };
+
+ can0: can@f8000000 {
+ compatible = "bosch,m_can";
+ reg = <0xf8000000 0x100>, <0x300000 0x7800>;
+ reg-names = "m_can", "message_ram";
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0
+ 68 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "int0", "int1";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
+ clock-names = "hclk", "cclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
+ assigned-clock-rates = <480000000>, <40000000>;
+ assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+ status = "disabled";
+ };
+
+ can1: can@f8004000 {
+ compatible = "bosch,m_can";
+ reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
+ reg-names = "m_can", "message_ram";
+ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0
+ 69 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "int0", "int1";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
+ clock-names = "hclk", "cclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
+ assigned-clock-rates = <480000000>, <40000000>;
+ assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+ status = "disabled";
+ };
+
+ tcb: timer@f8008000 {
+ compatible = "microchip,sam9x7-tcb","microchip,sam9x60-tcb", "simple-mfd", "syscon";
+ reg = <0xf8008000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
+ clock-names = "t0_clk", "slow_clk";
+ status = "disabled";
+ };
+
+ flx6: flexcom@f8010000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8010000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8010000 0x800>;
+ status = "disabled";
+
+ uart6: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx7: flexcom@f8014000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8014000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8014000 0x800>;
+ status = "disabled";
+
+ uart7: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx8: flexcom@f8018000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8018000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8018000 0x800>;
+ status = "disabled";
+
+ uart8: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx0: flexcom@f801c000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf801c000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf801c000 0x800>;
+ status = "disabled";
+
+ uart0: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi0: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx1: flexcom@f8020000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8020000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8020000 0x800>;
+ status = "disabled";
+
+ uart1: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi1: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx2: flexcom@f8024000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8024000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8024000 0x800>;
+ status = "disabled";
+
+ uart2: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi2: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx3: flexcom@f8028000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8028000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8028000 0x800>;
+ status = "disabled";
+
+ uart3: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi3: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ gmac: ethernet@f802c000 {
+ compatible = "microchip,sam9x7-gem", "microchip,sama7g5-gem" ;
+ reg = <0xf802c000 0x1000>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 0 */
+ 60 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 1 */
+ 61 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 2 */
+ 62 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 3 */
+ 63 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 4 */
+ 64 IRQ_TYPE_LEVEL_HIGH 3>; /* Queue 5 */
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_GCK 67>;
+ clock-names = "hclk", "pclk", "tsu_clk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 67>;
+ status = "disabled";
+ };
+
+ flx9: flexcom@f8040000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8040000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8040000 0x800>;
+ status = "disabled";
+
+ uart9: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx10: flexcom@f8044000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8044000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8044000 0x800>;
+ status = "disabled";
+
+ uart10: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ sfr: sfr@f8050000 {
+ compatible = "microchip,sam9x7-sfr, microchip,sam9x60-sfr", "syscon";
+ reg = <0xf8050000 0x100>;
+ };
+
+ matrix: matrix@ffffde00 {
+ compatible = "microchip,sam9x7-matrix", "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
+ reg = <0xffffde00 0x200>;
+ };
+
+ pmecc: ecc-engine@ffffe000 {
+ compatible = "microchip,sam9x7-pmecc", "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
+ reg = <0xffffe000 0x300>,
+ <0xffffe600 0x100>;
+ };
+
+ mpddrc: mpddrc@ffffe800 {
+ compatible = "microchip,sam9x7-ddramc", "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
+ reg = <0xffffe800 0x200>;
+ clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+ clock-names = "ddrck", "mpddr";
+ };
+
+ smc: smc@ffffea00 {
+ compatible = "microchip,sam9x7-smc", "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
+ reg = <0xffffea00 0x100>;
+ };
+
+ aic: interrupt-controller@fffff100 {
+ compatible = "microchip,sam9x7-aic";
+ reg = <0xfffff100 0x100>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ atmel,external-irqs = <31>;
+ };
+
+ dbgu: serial@fffff200 {
+ compatible = "microchip,sam9x7-dbgu", "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfffff200 0x200>;
+ interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(28))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(29))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl@fffff400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-mfd";
+ ranges = <0xfffff400 0xfffff400 0x800>;
+
+ /* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
+ atmel,mux-mask = <
+ /* A B C D */
+ 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000 /* pioA */
+ 0x07ffffff 0x0805fe7f 0x01ff9f80 0x06078000 /* pioB */
+ 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000 /* pioC */
+ 0x00003fff 0x00003fe0 0x0000003f 0x00000000 /* pioD */
+ >;
+
+ pioA: gpio@fffff400 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <26>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+ };
+
+ pioD: gpio@fffffa00 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <22>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ compatible = "microchip,sam9x7-pmc", "syscon";
+ reg = <0xfffffc00 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ #clock-cells = <2>;
+ clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+ clock-names = "td_slck", "md_slck", "main_xtal";
+ };
+
+ reset_controller: rstc@fffffe00 {
+ compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
+ reg = <0xfffffe00 0x10>;
+ clocks = <&clk32k 0>;
+ };
+
+ shutdown_controller: shdwc@fffffe10 {
+ compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
+ reg = <0xfffffe10 0x10>;
+ clocks = <&clk32k 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ atmel,wakeup-rtc-timer;
+ atmel,wakeup-rtt-timer;
+ status = "disabled";
+ };
+
+ rtt: rtc@fffffe20 {
+ compatible = "microchip,sam9x7-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+ reg = <0xfffffe20 0x20>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ };
+
+ clk32k: sckc@fffffe50 {
+ compatible = "microchip,sam9x7-sckc", "microchip,sam9x60-sckc";
+ reg = <0xfffffe50 0x4>;
+ clocks = <&slow_xtal>;
+ #clock-cells = <1>;
+ };
+
+ gpbr: syscon@fffffe60 {
+ compatible = "microchip,sam9x7-gbpr", "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+ reg = <0xfffffe60 0x10>;
+ };
+
+ rtc: rtc@fffffea8 {
+ compatible = "microchip,sam9x7-rtc", "microchip,sam9x60-rtc";
+ reg = <0xfffffea8 0x100>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ };
+
+ watchdog: watchdog@ffffff80 {
+ compatible = "microchip,sam9x7-wdt", "microchip,sam9x60-wdt";
+ reg = <0xffffff80 0x24>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Varshini Rajendran <varshini.rajendran@microchip.com>
To: <robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<conor+dt@kernel.org>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>, <claudiu.beznea@microchip.com>,
<mturquette@baylibre.com>, <sboyd@kernel.org>,
<herbert@gondor.apana.org.au>, <davem@davemloft.net>,
<vkoul@kernel.org>, <tglx@linutronix.de>, <maz@kernel.org>,
<lee@kernel.org>, <ulf.hansson@linaro.org>,
<tudor.ambarus@linaro.org>, <miquel.raynal@bootlin.com>,
<richard@nod.at>, <vigneshr@ti.com>, <edumazet@google.com>,
<kuba@kernel.org>, <pabeni@redhat.com>,
<linus.walleij@linaro.org>, <p.zabel@pengutronix.de>,
<olivia@selenic.com>, <a.zummo@towertech.it>,
<radu_nicolae.pirea@upb.ro>, <richard.genoud@gmail.com>,
<gregkh@linuxfoundation.org>, <lgirdwood@gmail.com>,
<broonie@kernel.org>, <wim@linux-watchdog.org>,
<linux@roeck-us.net>, <arnd@arndb.de>, <olof@lixom.net>,
<soc@kernel.org>, <linux@armlinux.org.uk>, <sre@kernel.org>,
<jerry.ray@microchip.com>, <horatiu.vultur@microchip.com>,
<durai.manickamkr@microchip.com>,
<varshini.rajendran@microchip.com>, <andrew@lunn.ch>,
<alain.volmat@foss.st.com>, <neil.armstrong@linaro.org>,
<mihai.sain@microchip.com>, <eugen.hristev@collabora.com>,
<devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-clk@vger.kernel.org>,
<linux-crypto@vger.kernel.org>, <dmaengine@vger.kernel.org>,
<linux-i2c@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
<linux-mtd@lists.infradead.org>, <netdev@vger.kernel.org>,
<linux-gpio@vger.kernel.org>, <linux-rtc@vger.kernel.org>,
<linux-spi@vger.kernel.org>, <linux-serial@vger.kernel.org>,
<alsa-devel@alsa-project.org>, <linux-usb@vger.kernel.org>,
<linux-watchdog@vger.kernel.org>, <linux-pm@vger.kernel.org>
Cc: <Hari.PrasathGE@microchip.com>, <cristian.birsan@microchip.com>,
<balamanikandan.gunasundar@microchip.com>,
<manikandan.m@microchip.com>, <dharma.b@microchip.com>,
<nayabbasha.sayed@microchip.com>, <balakrishnan.s@microchip.com>
Subject: [PATCH v2 43/45] ARM: dts: at91: sam9x7: add device tree for SoC
Date: Sat, 24 Jun 2023 02:00:54 +0530 [thread overview]
Message-ID: <20230623203056.689705-44-varshini.rajendran@microchip.com> (raw)
In-Reply-To: <20230623203056.689705-1-varshini.rajendran@microchip.com>
Add device tree file for SAM9X7 SoC family.
Co-developed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
---
arch/arm/boot/dts/sam9x7.dtsi | 1237 +++++++++++++++++++++++++++++++++
1 file changed, 1237 insertions(+)
create mode 100644 arch/arm/boot/dts/sam9x7.dtsi
diff --git a/arch/arm/boot/dts/sam9x7.dtsi b/arch/arm/boot/dts/sam9x7.dtsi
new file mode 100644
index 000000000000..535a55f13dd0
--- /dev/null
+++ b/arch/arm/boot/dts/sam9x7.dtsi
@@ -0,0 +1,1237 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "Microchip SAM9X7 SoC";
+ compatible = "microchip,sam9x7";
+ interrupt-parent = <&aic>;
+
+ aliases {
+ serial0 = &dbgu;
+ gpio0 = &pioA;
+ gpio1 = &pioB;
+ gpio2 = &pioC;
+ gpio3 = &pioD;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,arm926ej-s";
+ device_type = "cpu";
+ reg = <0>;
+ };
+ };
+
+ clocks {
+ slow_xtal: clock-slowxtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ main_xtal: clock-mainxtal {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+ };
+
+ sram: sram@300000 {
+ compatible = "mmio-sram";
+ reg = <0x300000 0x10000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x300000 0x10000>;
+ };
+
+ ahb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usb0: gadget@500000 {
+ compatible = "microchip,sam9x7-udc", "microchip,sam9x60-udc";
+ reg = <0x500000 0x100000>,
+ <0xf803c000 0x400>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ clock-names = "pclk", "hclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ assigned-clock-rates = <480000000>;
+ status = "disabled";
+ };
+
+ ohci0: usb@600000 {
+ compatible = "microchip,sam9x7-ohci", "atmel,at91rm9200-ohci", "usb-ohci";
+ reg = <0x600000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
+ status = "disabled";
+ };
+
+ ehci0: usb@700000 {
+ compatible = "microchip,sam9x7-ehci", "atmel,at91sam9g45-ehci", "usb-ehci";
+ reg = <0x700000 0x100000>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+ clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
+ clock-names = "usb_clk", "ehci_clk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ assigned-clock-rates = <480000000>;
+ status = "disabled";
+ };
+
+ sdmmc0: sdio-host@80000000 {
+ compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+ reg = <0x80000000 0x300>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+ clock-names = "hclock", "multclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+ assigned-clock-rates = <100000000>;
+ status = "disabled";
+ };
+
+ sdmmc1: sdio-host@90000000 {
+ compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+ reg = <0x90000000 0x300>;
+ interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+ clock-names = "hclock", "multclk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+ assigned-clock-rates = <100000000>;
+ status = "disabled";
+ };
+
+ apb {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ flx4: flexcom@f0000000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0000000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0000000 0x800>;
+ status = "disabled";
+
+ uart4: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi4: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(8))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(9))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx5: flexcom@f0004000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0004000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0004000 0x800>;
+ status = "disabled";
+
+ uart5: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi5: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(10))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(11))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ dma0: dma-controller@f0008000 {
+ compatible = "microchip,sam9x7-dma", "microchip,sam9x60-dma", "atmel,sama5d4-dma";
+ reg = <0xf0008000 0x1000>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+ #dma-cells = <1>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+ clock-names = "dma_clk";
+ status = "disabled";
+ };
+
+ ssc: ssc@f0010000 {
+ compatible = "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(38))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(39))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+ clock-names = "pclk";
+ status = "disabled";
+ };
+
+ i2s: i2s@f001c000 {
+ compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
+ reg = <0xf001c000 0x100>;
+ interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(36))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(37))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+ clock-names = "pclk", "gclk";
+ status = "disabled";
+ };
+
+ flx11: flexcom@f0020000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0020000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0020000 0x800>;
+ status = "disabled";
+
+ uart11: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(22))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(23))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx12: flexcom@f0024000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf0024000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf0024000 0x800>;
+ status = "disabled";
+
+ uart12: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(24))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(25))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ pit64b0: timer@f0028000 {
+ compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+ reg = <0xf0028000 0x100>;
+ interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+ clock-names = "pclk", "gclk";
+ };
+
+ sha: crypto@f002c000 {
+ compatible = "microchip,sam9x7-sha", "atmel,at91sam9g46-sha";
+ reg = <0xf002c000 0x100>;
+ interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(34))>;
+ dma-names = "tx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+ clock-names = "sha_clk";
+ };
+
+ trng: rng@f0030000 {
+ compatible = "microchip,sam9x7-trng", "microchip,sam9x60-trng";
+ reg = <0xf0030000 0x100>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+ status = "disabled";
+ };
+
+ aes: crypto@f0034000 {
+ compatible = "microchip,sam9x7-aes", "atmel,at91sam9g46-aes";
+ reg = <0xf0034000 0x100>;
+ interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(32))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(33))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+ clock-names = "aes_clk";
+ };
+
+ tdes: crypto@f0038000 {
+ compatible = "microchip,sam9x7-tdes", "atmel,at91sam9g46-tdes";
+ reg = <0xf0038000 0x100>;
+ interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(31))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(30))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+ clock-names = "tdes_clk";
+ };
+
+ classd: classd@f003c000 {
+ compatible = "microchip,sam9x7-classd", "atmel,sama5d2-classd";
+ reg = <0xf003c000 0x100>;
+ interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(35))>;
+ dma-names = "tx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+ clock-names = "pclk", "gclk";
+ status = "disabled";
+ };
+
+ pit64b1: timer@f0040000 {
+ compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+ reg = <0xf0040000 0x100>;
+ interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+ clock-names = "pclk", "gclk";
+ };
+
+ can0: can@f8000000 {
+ compatible = "bosch,m_can";
+ reg = <0xf8000000 0x100>, <0x300000 0x7800>;
+ reg-names = "m_can", "message_ram";
+ interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0
+ 68 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "int0", "int1";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
+ clock-names = "hclk", "cclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
+ assigned-clock-rates = <480000000>, <40000000>;
+ assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+ status = "disabled";
+ };
+
+ can1: can@f8004000 {
+ compatible = "bosch,m_can";
+ reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
+ reg-names = "m_can", "message_ram";
+ interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0
+ 69 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "int0", "int1";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
+ clock-names = "hclk", "cclk";
+ assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
+ assigned-clock-rates = <480000000>, <40000000>;
+ assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+ bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+ status = "disabled";
+ };
+
+ tcb: timer@f8008000 {
+ compatible = "microchip,sam9x7-tcb","microchip,sam9x60-tcb", "simple-mfd", "syscon";
+ reg = <0xf8008000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
+ clock-names = "t0_clk", "slow_clk";
+ status = "disabled";
+ };
+
+ flx6: flexcom@f8010000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8010000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8010000 0x800>;
+ status = "disabled";
+
+ uart6: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(12))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(13))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx7: flexcom@f8014000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8014000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8014000 0x800>;
+ status = "disabled";
+
+ uart7: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(14))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(15))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx8: flexcom@f8018000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8018000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8018000 0x800>;
+ status = "disabled";
+
+ uart8: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c8: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(16))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(17))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx0: flexcom@f801c000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf801c000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf801c000 0x800>;
+ status = "disabled";
+
+ uart0: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi0: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(0))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(1))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx1: flexcom@f8020000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8020000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8020000 0x800>;
+ status = "disabled";
+
+ uart1: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi1: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(2))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(3))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx2: flexcom@f8024000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8024000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8024000 0x800>;
+ status = "disabled";
+
+ uart2: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi2: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(4))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(5))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx3: flexcom@f8028000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8028000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8028000 0x800>;
+ status = "disabled";
+
+ uart3: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ spi3: spi@400 {
+ compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ clock-names = "spi_clk";
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(6))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(7))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ gmac: ethernet@f802c000 {
+ compatible = "microchip,sam9x7-gem", "microchip,sama7g5-gem" ;
+ reg = <0xf802c000 0x1000>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 0 */
+ 60 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 1 */
+ 61 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 2 */
+ 62 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 3 */
+ 63 IRQ_TYPE_LEVEL_HIGH 3 /* Queue 4 */
+ 64 IRQ_TYPE_LEVEL_HIGH 3>; /* Queue 5 */
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_GCK 67>;
+ clock-names = "hclk", "pclk", "tsu_clk";
+ assigned-clocks = <&pmc PMC_TYPE_GCK 67>;
+ status = "disabled";
+ };
+
+ flx9: flexcom@f8040000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8040000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8040000 0x800>;
+ status = "disabled";
+
+ uart9: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(18))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(19))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx10: flexcom@f8044000 {
+ compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+ reg = <0xf8044000 0x200>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0xf8044000 0x800>;
+ status = "disabled";
+
+ uart10: serial@200 {
+ compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ clock-names = "usart";
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@600 {
+ compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(20))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) |
+ AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(21))>;
+ dma-names = "tx", "rx";
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ sfr: sfr@f8050000 {
+ compatible = "microchip,sam9x7-sfr, microchip,sam9x60-sfr", "syscon";
+ reg = <0xf8050000 0x100>;
+ };
+
+ matrix: matrix@ffffde00 {
+ compatible = "microchip,sam9x7-matrix", "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
+ reg = <0xffffde00 0x200>;
+ };
+
+ pmecc: ecc-engine@ffffe000 {
+ compatible = "microchip,sam9x7-pmecc", "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
+ reg = <0xffffe000 0x300>,
+ <0xffffe600 0x100>;
+ };
+
+ mpddrc: mpddrc@ffffe800 {
+ compatible = "microchip,sam9x7-ddramc", "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
+ reg = <0xffffe800 0x200>;
+ clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+ clock-names = "ddrck", "mpddr";
+ };
+
+ smc: smc@ffffea00 {
+ compatible = "microchip,sam9x7-smc", "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
+ reg = <0xffffea00 0x100>;
+ };
+
+ aic: interrupt-controller@fffff100 {
+ compatible = "microchip,sam9x7-aic";
+ reg = <0xfffff100 0x100>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ atmel,external-irqs = <31>;
+ };
+
+ dbgu: serial@fffff200 {
+ compatible = "microchip,sam9x7-dbgu", "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ reg = <0xfffff200 0x200>;
+ interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(28))>,
+ <&dma0
+ (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+ AT91_XDMAC_DT_PERID(29))>;
+ dma-names = "tx", "rx";
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl@fffff400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-mfd";
+ ranges = <0xfffff400 0xfffff400 0x800>;
+
+ /* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
+ atmel,mux-mask = <
+ /* A B C D */
+ 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000 /* pioA */
+ 0x07ffffff 0x0805fe7f 0x01ff9f80 0x06078000 /* pioB */
+ 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000 /* pioC */
+ 0x00003fff 0x00003fe0 0x0000003f 0x00000000 /* pioD */
+ >;
+
+ pioA: gpio@fffff400 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff400 0x200>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+ };
+
+ pioB: gpio@fffff600 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff600 0x200>;
+ interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <26>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+ };
+
+ pioC: gpio@fffff800 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffff800 0x200>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+ };
+
+ pioD: gpio@fffffa00 {
+ compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+ reg = <0xfffffa00 0x200>;
+ interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #gpio-lines = <22>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ compatible = "microchip,sam9x7-pmc", "syscon";
+ reg = <0xfffffc00 0x200>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ #clock-cells = <2>;
+ clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+ clock-names = "td_slck", "md_slck", "main_xtal";
+ };
+
+ reset_controller: rstc@fffffe00 {
+ compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
+ reg = <0xfffffe00 0x10>;
+ clocks = <&clk32k 0>;
+ };
+
+ shutdown_controller: shdwc@fffffe10 {
+ compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
+ reg = <0xfffffe10 0x10>;
+ clocks = <&clk32k 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ atmel,wakeup-rtc-timer;
+ atmel,wakeup-rtt-timer;
+ status = "disabled";
+ };
+
+ rtt: rtc@fffffe20 {
+ compatible = "microchip,sam9x7-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+ reg = <0xfffffe20 0x20>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ };
+
+ clk32k: sckc@fffffe50 {
+ compatible = "microchip,sam9x7-sckc", "microchip,sam9x60-sckc";
+ reg = <0xfffffe50 0x4>;
+ clocks = <&slow_xtal>;
+ #clock-cells = <1>;
+ };
+
+ gpbr: syscon@fffffe60 {
+ compatible = "microchip,sam9x7-gbpr", "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+ reg = <0xfffffe60 0x10>;
+ };
+
+ rtc: rtc@fffffea8 {
+ compatible = "microchip,sam9x7-rtc", "microchip,sam9x60-rtc";
+ reg = <0xfffffea8 0x100>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ };
+
+ watchdog: watchdog@ffffff80 {
+ compatible = "microchip,sam9x7-wdt", "microchip,sam9x60-wdt";
+ reg = <0xffffff80 0x24>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&clk32k 0>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.25.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2023-06-23 21:08 UTC|newest]
Thread overview: 167+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-23 20:30 [PATCH v2 00/45] Add support for sam9x7 SoC family Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 01/45] dt-bindings: microchip: atmel,at91rm9200-tcb: add sam9x60, sam9x7 compatible Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:53 ` Krzysztof Kozlowski
2023-06-24 7:53 ` Krzysztof Kozlowski
2023-06-24 9:19 ` Krzysztof Kozlowski
2023-06-24 9:19 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 02/45] dt-bindings: usb: ehci: Add atmel at91sam9g45-ehci compatible Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:53 ` Krzysztof Kozlowski
2023-06-24 7:53 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 03/45] dt-bindings: usb: generic-ehci: Document clock-names property Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:54 ` Krzysztof Kozlowski
2023-06-24 7:54 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 04/45] dt-bindings: net: cdns,macb: add documentation for sam9x7 ethernet interface Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:54 ` Krzysztof Kozlowski
2023-06-24 7:54 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 05/45] ARM: at91: pm: add support for sam9x7 SoC family Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 06/45] ARM: at91: pm: add sam9x7 SoC init config Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 07/45] ARM: at91: add support in SoC driver for new sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 08/45] clk: at91: clk-sam9x60-pll: re-factor to support individual core freq outputs Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 09/45] clk: at91: sam9x7: add support for HW PLL freq dividers Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 10/45] clk: at91: sama7g5: move mux table macros to header file Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 11/45] dt-bindings: clk: at91: add bindings for SAM9X7's clock controller Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 12/45] dt-bindings: reset: atmel,at91sam9260-reset: add sam9x7 binding Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:57 ` Krzysztof Kozlowski
2023-06-24 7:57 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 13/45] dt-bindings: atmel-sysreg: add bindings for sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:00 ` Krzysztof Kozlowski
2023-06-24 8:00 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 14/45] dt-bindings: crypto: add bindings for sam9x7 in Atmel AES Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:58 ` Krzysztof Kozlowski
2023-06-24 7:58 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 15/45] dt-bindings: crypto: add bindings for sam9x7 in Atmel SHA Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:59 ` Krzysztof Kozlowski
2023-06-24 7:59 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 16/45] dt-bindings: crypto: add bindings for sam9x7 in Atmel TDES Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 7:59 ` Krzysztof Kozlowski
2023-06-24 7:59 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 17/45] dt-bindings: dmaengine: at_xdmac: add compatible with microchip,sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:27 ` Krzysztof Kozlowski
2023-06-24 8:27 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 18/45] dt-bindings: i2c: at91: Add SAM9X7 compatible string Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:00 ` Krzysztof Kozlowski
2023-06-24 8:00 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 19/45] dt-bindings: mfd: " Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 20/45] dt-bindings: atmel-gpbr: add microchip,sam9x7-gpbr Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 21/45] dt-bindings: atmel-matrix: add microchip,sam9x7-matrix Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 22/45] dt-bindings: atmel-smc: add microchip,sam9x7-smc Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 23/45] dt-bindings: atmel-ssc: add microchip,sam9x7-ssc Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 24/45] dt-bindings: sdhci-of-at91: add microchip,sam9x7-sdhci Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 25/45] dt-bindings: atmel-nand: add microchip,sam9x7-pmecc Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 26/45] dt-bindings: pinctrl: at91: add bindings for SAM9X7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-24 8:24 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 27/45] dt-bindings: rng: atmel,at91-trng: document sam9x7 TRNG Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:01 ` Krzysztof Kozlowski
2023-06-24 8:01 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 28/45] dt-bindings: rtc: at91rm9200: add sam9x7 compatible Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:01 ` Krzysztof Kozlowski
2023-06-24 8:01 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 29/45] dt-bindings: rtt: at91rm9260: " Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 30/45] dt-bindings: serial: atmel,at91-usart: add compatible for sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 31/45] dt-bindings: atmel-classd: add sam9x7 compatible Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 23:43 ` Rob Herring
2023-06-23 23:43 ` Rob Herring
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 32/45] spi: dt-bindings: atmel,at91rm9200-spi: " Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-24 8:02 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 33/45] dt-bindings: usb: atmel: Update DT bindings documentation for sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 34/45] dt-bindings: watchdog: sama5d4-wdt: add compatible for sam9x7-wdt Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:03 ` Krzysztof Kozlowski
2023-06-24 8:03 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 35/45] dt-bindings: irqchip/atmel-aic5: Add support for sam9x7 aic Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-24 8:23 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 36/45] clk: at91: sam9x7: add sam9x7 pmc driver Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 37/45] irqchip/atmel-aic5: Add support for sam9x7 aic Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 38/45] power: reset: at91-poweroff: lookup for proper pmc dt node for sam9x7 Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 39/45] power: reset: at91-reset: add reset support for sam9x7 SoC Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 40/45] power: reset: at91-reset: add sdhwc " Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 41/45] ARM: at91: Kconfig: add config flag for SAM9X7 SoC Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` [PATCH v2 42/45] ARM: configs: at91: enable config flags for sam9x7 SoC family Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran [this message]
2023-06-23 20:30 ` [PATCH v2 43/45] ARM: dts: at91: sam9x7: add device tree for SoC Varshini Rajendran
2023-06-24 8:09 ` Krzysztof Kozlowski
2023-06-24 8:09 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 44/45] dt-bindings: arm: add sam9x75 curiosity board Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:03 ` Krzysztof Kozlowski
2023-06-24 8:03 ` Krzysztof Kozlowski
2023-06-23 20:30 ` [PATCH v2 45/45] ARM: dts: at91: sam9x75_curiosity: add device tree for " Varshini Rajendran
2023-06-23 20:30 ` Varshini Rajendran
2023-06-24 8:12 ` Krzysztof Kozlowski
2023-06-24 8:12 ` Krzysztof Kozlowski
2023-06-24 0:52 ` (subset) [PATCH v2 00/45] Add support for sam9x7 SoC family Mark Brown
2023-06-24 0:52 ` Mark Brown
2023-06-24 8:13 ` Krzysztof Kozlowski
2023-06-24 8:13 ` Krzysztof Kozlowski
2023-06-24 7:56 ` Krzysztof Kozlowski
2023-06-24 7:56 ` Krzysztof Kozlowski
2023-06-24 8:28 ` Krzysztof Kozlowski
2023-06-24 8:28 ` Krzysztof Kozlowski
2023-07-05 20:42 ` patchwork-bot+linux-soc
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230623203056.689705-44-varshini.rajendran@microchip.com \
--to=varshini.rajendran@microchip.com \
--cc=Hari.PrasathGE@microchip.com \
--cc=a.zummo@towertech.it \
--cc=alain.volmat@foss.st.com \
--cc=alexandre.belloni@bootlin.com \
--cc=alsa-devel@alsa-project.org \
--cc=andrew@lunn.ch \
--cc=arnd@arndb.de \
--cc=balakrishnan.s@microchip.com \
--cc=balamanikandan.gunasundar@microchip.com \
--cc=broonie@kernel.org \
--cc=claudiu.beznea@microchip.com \
--cc=conor+dt@kernel.org \
--cc=cristian.birsan@microchip.com \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=dharma.b@microchip.com \
--cc=dmaengine@vger.kernel.org \
--cc=durai.manickamkr@microchip.com \
--cc=edumazet@google.com \
--cc=eugen.hristev@collabora.com \
--cc=gregkh@linuxfoundation.org \
--cc=herbert@gondor.apana.org.au \
--cc=horatiu.vultur@microchip.com \
--cc=jerry.ray@microchip.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kuba@kernel.org \
--cc=lee@kernel.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-crypto@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-rtc@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=linux@roeck-us.net \
--cc=manikandan.m@microchip.com \
--cc=maz@kernel.org \
--cc=mihai.sain@microchip.com \
--cc=miquel.raynal@bootlin.com \
--cc=mturquette@baylibre.com \
--cc=nayabbasha.sayed@microchip.com \
--cc=neil.armstrong@linaro.org \
--cc=netdev@vger.kernel.org \
--cc=nicolas.ferre@microchip.com \
--cc=olivia@selenic.com \
--cc=olof@lixom.net \
--cc=p.zabel@pengutronix.de \
--cc=pabeni@redhat.com \
--cc=radu_nicolae.pirea@upb.ro \
--cc=richard.genoud@gmail.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=soc@kernel.org \
--cc=sre@kernel.org \
--cc=tglx@linutronix.de \
--cc=tudor.ambarus@linaro.org \
--cc=ulf.hansson@linaro.org \
--cc=vigneshr@ti.com \
--cc=vkoul@kernel.org \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.