From: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
To: Russell King - ARM Linux <linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>
Cc: Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Jason Cooper <jason-NLaQJdtUoK4Be96aLqz0jA@public.gmane.org>,
linux ARM
<linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>
Subject: Re: [PATCH RFC RFT 0/2] ARM: Kirkwood: Synology DT files
Date: Sat, 11 Jan 2014 00:09:11 +1000 [thread overview]
Message-ID: <52CFFF07.5080806@killerwolves.net> (raw)
In-Reply-To: <20140110112846.GG27432-l+eeeJia6m9vn6HldHNs0ANdhmdF6hFW@public.gmane.org>
On 10/01/14 21:28, Russell King - ARM Linux wrote:
> On Fri, Jan 10, 2014 at 11:01:06AM +1000, Ben Peddell wrote:
>> It appears the initrd address in the devicetree structure (which is
>> filled in from what is passed by the bootloader when
>> CONFIG_ARM_ATAG_DTB_COMPAT is set) is processed _after_ the address in
>> the initrd= kernel parameter is processed.
>
> That's wrong. Kernel parameters should always override what's passed by
> boot loaders etc.
In that case, what I saw was a bug - note that this only occurs when
DeviceTree is enabled:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Jul 6 2010 - 19:26:08) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B43C
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 480Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
[4096kB@f8000000] Flash: 4 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 1 is AUDIO
USB 0: host mode
Synology Model: DS211j
Fan Status: Good
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv ipaddr 192.168.200.62
Marvell>> setenv serverip 192.168.200.16
Marvell>> tftp 0x01000000 uImage-3.13-rc7-ds211j-git-fdt
Using egiga0 device
TFTP from server 192.168.200.16; our IP address is 192.168.200.62
Filename 'uImage-3.13-rc7-ds211j-git-fdt'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 1954736 (1dd3b0 hex)
Marvell>> setenv bootargs console=ttyS0,115200 ip=off initrd=0x00800040,0x0013FFC0 root=/dev/md0 rw syno_hw_version=DS211j ihd_num=2 netif_num=1 earlyprintk
Marvell>> bootm 0x01000000 0xf8280000
## Booting image at 01000000 ...
Bad Magic Number
Marvell>> tftp 0x01000000 uImage-3.13-rc7-ds211j-git-fdt
Using egiga0 device
TFTP from server 192.168.200.16; our IP address is 192.168.200.62
Filename 'uImage-3.13-rc7-ds211j-git-fdt'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 1954800 (1dd3f0 hex)
Marvell>> bootm 0x01000000 0xf8280000
## Booting image at 01000000 ...
Image Name: linux-3.13-rc7-ds211j+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1954736 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: altair-boot
Image Type: ARM Linux RAMDisk Image (unknown compression)
Data Size: 1022268 Bytes = 998.3 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.13.0-rc7-ds211j+ (root@lurch) (gcc version 4.8.2 (Gentoo 4.8.2 p1.3, pie-0.5.8) ) #2 Thu Jan 9 08:52:24 EST 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Synology DS210 v10, v20, v30, DS211j
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] INITRD: 0xf8280040+0x000f993c is not a memory region - disabling initrd
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,0x0013FFC0 root=/dev/md0 rw syno_hw_version=DS211j ihd_num=2 netif_num=1 earlyprintk
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 124716K/131072K available (3466K kernel code, 191K rwdata, 1084K rodata, 166K init, 215K bss, 6356K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0479d6c (4552 kB)
[ 0.000000] .init : 0xc047a000 - 0xc04a380c ( 167 kB)
[ 0.000000] .data : 0xc04a4000 - 0xc04d3e80 ( 192 kB)
[ 0.000000] .bss : 0xc04d3e80 - 0xc0509b30 ( 216 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[ 0.000000] Console: colour dummy device 80x30
[ 0.004804] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.092919] pid_max: default: 32768 minimum: 301
[ 0.097708] Mount-cache hash table entries: 512
[ 0.104591] CPU: Testing write buffer coherency: ok
[ 0.109822] Setting up static identity map for 0x348060 - 0x3480b8
[ 0.117170] devtmpfs: initialized
[ 0.121538] xor: measuring software checksum speed
[ 0.220035] arm4regs : 1084.400 MB/sec
[ 0.320030] 8regs : 651.200 MB/sec
[ 0.420029] 32regs : 901.200 MB/sec
[ 0.424280] xor: using function: arm4regs (1084.400 MB/sec)
[ 0.429916] pinctrl core: initialized pinctrl subsystem
[ 0.436009] regulator-dummy: no parameters
[ 0.440606] NET: Registered protocol family 16
[ 0.445560] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.455243] cpuidle: using governor ladder
[ 0.459410] cpuidle: using governor menu
[ 0.463559] Kirkwood: MV88F6281-A1, TCLK=0.
[ 0.467921] Feroceon L2: Enabling L2
[ 0.471615] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.478793] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.494565] No ATAGs?
[ 0.507801] bio: create slab <bio-0> at 0
[ 0.680061] raid6: int32x1 100 MB/s
[ 0.850266] raid6: int32x2 131 MB/s
[ 1.020409] raid6: int32x4 123 MB/s
[ 1.190124] raid6: int32x8 130 MB/s
[ 1.193936] raid6: using algorithm int32x2 (131 MB/s)
[ 1.199042] raid6: using intx1 recovery algorithm
[ 1.204120] hdd2power: Failed to request enable GPIO31: -517
[ 1.209988] reg-fixed-voltage 1.regulator: Failed to register regulator: -517
[ 1.217197] platform 1.regulator: Driver reg-fixed-voltage requests probe deferral
[ 1.225708] SCSI subsystem initialized
[ 1.231520] Switched to clocksource orion_clocksource
[ 1.249315] NET: Registered protocol family 2
[ 1.254161] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.261187] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.267625] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.274087] TCP: reno registered
[ 1.277385] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.283303] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.289768] NET: Registered protocol family 1
[ 1.294402] RPC: Registered named UNIX socket transport module.
[ 1.300373] RPC: Registered udp transport module.
[ 1.305150] RPC: Registered tcp transport module.
[ 1.309911] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.316588] Trying to unpack rootfs image as initramfs...
[ 1.322063] Unable to handle kernel paging request at virtual address b8280040
[ 1.329334] pgd = c0004000
[ 1.332118] [b8280040] *pgd=00000000
[ 1.335766] Internal error: Oops: 5 [#1] ARM
[ 1.340098] Modules linked in:
[ 1.343232] CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc7-ds211j+ #2
[ 1.350072] task: c7839bc0 ti: c783a000 task.ti: c783a000
[ 1.355529] PC is at unpack_to_rootfs+0xa8/0x2b0
[ 1.360206] LR is at unpack_to_rootfs+0x44/0x2b0
[ 1.364883] pc : [<c047c998>] lr : [<c047c934>] psr: 20000053
[ 1.364883] sp : c783be40 ip : 000008d8 fp : 00000000
[ 1.376474] r10: 00000000 r9 : 00000068 r8 : c047d020
[ 1.381755] r7 : c049d068 r6 : b8280040 r5 : 000f993c r4 : c049d068
[ 1.388329] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : c7924000
[ 1.394905] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 1.402343] Control: 0005397f Table: 00004000 DAC: 00000017
[ 1.408140] Process swapper (pid: 1, stack limit = 0xc783a1c0)
[ 1.414024] Stack: (0xc783be40 to 0xc783c000)
[ 1.418446] be40: 00000000 c04a34fc c04d3f00 c047d020 00000000 00000000 c04d3f4c c0343368
[ 1.426671] be60: c03f85f6 c04d3f50 00000000 c04a34fc c04d3f00 c047d020 00000068 c04d3f50
[ 1.434897] be80: c04d3f4c c047d074 ffffffff 00000000 c04c1b5c c04fffc4 c04c1b5c c049023c
[ 1.443121] bea0: 00000068 00000000 c783a038 c0343368 c041909f c783becc 00000020 c783becc
[ 1.451346] bec0: 00000000 c049031c c041909f 00000000 00000020 00000005 c049bbc8 c04a34fc
[ 1.459572] bee0: c04d3f00 c047d020 00000068 00000000 c783a038 c000869c c782b6a0 c00d89c0
[ 1.467797] bf00: c782b700 c782b6a0 00000000 c782b6a0 c034c50c c04f7914 00000000 c00d8c5c
[ 1.476023] bf20: 00000068 c060edf7 00000000 c0031dc8 60000053 c0457d84 c0457704 00000068
[ 1.484247] bf40: 00000005 00000005 00000001 00000005 c049bbc8 c04a34fc c04d3f00 c04d3f00
[ 1.492473] bf60: 00000068 c049bbd8 00000000 c047ab14 00000005 00000005 c047a478 c002f124
[ 1.500697] bf80: 00000000 00000000 00000000 c0340fb4 00000000 00000000 00000000 00000000
[ 1.508923] bfa0: 00000000 c0340fbc 00000000 c000e050 00000000 00000000 00000000 00000000
[ 1.517147] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.525373] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 1.533606] [<c047c998>] (unpack_to_rootfs+0xa8/0x2b0) from [<c047d074>] (populate_rootfs+0x54/0x224)
[ 1.542873] [<c047d074>] (populate_rootfs+0x54/0x224) from [<c000869c>] (do_one_initcall+0x94/0x13c)
[ 1.552055] [<c000869c>] (do_one_initcall+0x94/0x13c) from [<c047ab14>] (kernel_init_freeable+0xf8/0x1b8)
[ 1.561671] [<c047ab14>] (kernel_init_freeable+0xf8/0x1b8) from [<c0340fbc>] (kernel_init+0x8/0x100)
[ 1.570852] [<c0340fbc>] (kernel_init+0x8/0x100) from [<c000e050>] (ret_from_fork+0x14/0x24)
[ 1.579339] Code: 1a000056 e3550000 0a000054 e1c7a1d0 (e5d63000)
[ 1.585525] ---[ end trace 4e31448959d8cde7 ]---
[ 1.590212] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 1.590212]
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: klightspeed@killerwolves.net (Ben Peddell)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH RFC RFT 0/2] ARM: Kirkwood: Synology DT files
Date: Sat, 11 Jan 2014 00:09:11 +1000 [thread overview]
Message-ID: <52CFFF07.5080806@killerwolves.net> (raw)
In-Reply-To: <20140110112846.GG27432@n2100.arm.linux.org.uk>
On 10/01/14 21:28, Russell King - ARM Linux wrote:
> On Fri, Jan 10, 2014 at 11:01:06AM +1000, Ben Peddell wrote:
>> It appears the initrd address in the devicetree structure (which is
>> filled in from what is passed by the bootloader when
>> CONFIG_ARM_ATAG_DTB_COMPAT is set) is processed _after_ the address in
>> the initrd= kernel parameter is processed.
>
> That's wrong. Kernel parameters should always override what's passed by
> boot loaders etc.
In that case, what I saw was a bug - note that this only occurs when
DeviceTree is enabled:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: Synology Disk Station LE
U-Boot 1.1.4 (Jul 6 2010 - 19:26:08) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B43C
Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 480Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 6 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
[4096kB at f8000000] Flash: 4 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Using default environment
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 1 is AUDIO
USB 0: host mode
Synology Model: DS211j
Fan Status: Good
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> setenv ipaddr 192.168.200.62
Marvell>> setenv serverip 192.168.200.16
Marvell>> tftp 0x01000000 uImage-3.13-rc7-ds211j-git-fdt
Using egiga0 device
TFTP from server 192.168.200.16; our IP address is 192.168.200.62
Filename 'uImage-3.13-rc7-ds211j-git-fdt'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 1954736 (1dd3b0 hex)
Marvell>> setenv bootargs console=ttyS0,115200 ip=off initrd=0x00800040,0x0013FFC0 root=/dev/md0 rw syno_hw_version=DS211j ihd_num=2 netif_num=1 earlyprintk
Marvell>> bootm 0x01000000 0xf8280000
## Booting image at 01000000 ...
Bad Magic Number
Marvell>> tftp 0x01000000 uImage-3.13-rc7-ds211j-git-fdt
Using egiga0 device
TFTP from server 192.168.200.16; our IP address is 192.168.200.62
Filename 'uImage-3.13-rc7-ds211j-git-fdt'.
Load address: 0x1000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#########################################################
done
Bytes transferred = 1954800 (1dd3f0 hex)
Marvell>> bootm 0x01000000 0xf8280000
## Booting image at 01000000 ...
Image Name: linux-3.13-rc7-ds211j+
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1954736 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at f8280000 ...
Image Name: altair-boot
Image Type: ARM Linux RAMDisk Image (unknown compression)
Data Size: 1022268 Bytes = 998.3 kB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.13.0-rc7-ds211j+ (root at lurch) (gcc version 4.8.2 (Gentoo 4.8.2 p1.3, pie-0.5.8) ) #2 Thu Jan 9 08:52:24 EST 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Synology DS210 v10, v20, v30, DS211j
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] INITRD: 0xf8280040+0x000f993c is not a memory region - disabling initrd
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,0x0013FFC0 root=/dev/md0 rw syno_hw_version=DS211j ihd_num=2 netif_num=1 earlyprintk
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 124716K/131072K available (3466K kernel code, 191K rwdata, 1084K rodata, 166K init, 215K bss, 6356K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0479d6c (4552 kB)
[ 0.000000] .init : 0xc047a000 - 0xc04a380c ( 167 kB)
[ 0.000000] .data : 0xc04a4000 - 0xc04d3e80 ( 192 kB)
[ 0.000000] .bss : 0xc04d3e80 - 0xc0509b30 ( 216 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[ 0.000000] Console: colour dummy device 80x30
[ 0.004804] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.092919] pid_max: default: 32768 minimum: 301
[ 0.097708] Mount-cache hash table entries: 512
[ 0.104591] CPU: Testing write buffer coherency: ok
[ 0.109822] Setting up static identity map for 0x348060 - 0x3480b8
[ 0.117170] devtmpfs: initialized
[ 0.121538] xor: measuring software checksum speed
[ 0.220035] arm4regs : 1084.400 MB/sec
[ 0.320030] 8regs : 651.200 MB/sec
[ 0.420029] 32regs : 901.200 MB/sec
[ 0.424280] xor: using function: arm4regs (1084.400 MB/sec)
[ 0.429916] pinctrl core: initialized pinctrl subsystem
[ 0.436009] regulator-dummy: no parameters
[ 0.440606] NET: Registered protocol family 16
[ 0.445560] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.455243] cpuidle: using governor ladder
[ 0.459410] cpuidle: using governor menu
[ 0.463559] Kirkwood: MV88F6281-A1, TCLK=0.
[ 0.467921] Feroceon L2: Enabling L2
[ 0.471615] Feroceon L2: Cache support initialised, in WT override mode.
[ 0.478793] [Firmware Info]: /ocp at f1000000/ethernet-controller at 72000/ethernet0-port at 0: local-mac-address is not set
[ 0.494565] No ATAGs?
[ 0.507801] bio: create slab <bio-0> at 0
[ 0.680061] raid6: int32x1 100 MB/s
[ 0.850266] raid6: int32x2 131 MB/s
[ 1.020409] raid6: int32x4 123 MB/s
[ 1.190124] raid6: int32x8 130 MB/s
[ 1.193936] raid6: using algorithm int32x2 (131 MB/s)
[ 1.199042] raid6: using intx1 recovery algorithm
[ 1.204120] hdd2power: Failed to request enable GPIO31: -517
[ 1.209988] reg-fixed-voltage 1.regulator: Failed to register regulator: -517
[ 1.217197] platform 1.regulator: Driver reg-fixed-voltage requests probe deferral
[ 1.225708] SCSI subsystem initialized
[ 1.231520] Switched to clocksource orion_clocksource
[ 1.249315] NET: Registered protocol family 2
[ 1.254161] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.261187] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 1.267625] TCP: Hash tables configured (established 1024 bind 1024)
[ 1.274087] TCP: reno registered
[ 1.277385] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.283303] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.289768] NET: Registered protocol family 1
[ 1.294402] RPC: Registered named UNIX socket transport module.
[ 1.300373] RPC: Registered udp transport module.
[ 1.305150] RPC: Registered tcp transport module.
[ 1.309911] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.316588] Trying to unpack rootfs image as initramfs...
[ 1.322063] Unable to handle kernel paging request at virtual address b8280040
[ 1.329334] pgd = c0004000
[ 1.332118] [b8280040] *pgd=00000000
[ 1.335766] Internal error: Oops: 5 [#1] ARM
[ 1.340098] Modules linked in:
[ 1.343232] CPU: 0 PID: 1 Comm: swapper Not tainted 3.13.0-rc7-ds211j+ #2
[ 1.350072] task: c7839bc0 ti: c783a000 task.ti: c783a000
[ 1.355529] PC is at unpack_to_rootfs+0xa8/0x2b0
[ 1.360206] LR is at unpack_to_rootfs+0x44/0x2b0
[ 1.364883] pc : [<c047c998>] lr : [<c047c934>] psr: 20000053
[ 1.364883] sp : c783be40 ip : 000008d8 fp : 00000000
[ 1.376474] r10: 00000000 r9 : 00000068 r8 : c047d020
[ 1.381755] r7 : c049d068 r6 : b8280040 r5 : 000f993c r4 : c049d068
[ 1.388329] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : c7924000
[ 1.394905] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 1.402343] Control: 0005397f Table: 00004000 DAC: 00000017
[ 1.408140] Process swapper (pid: 1, stack limit = 0xc783a1c0)
[ 1.414024] Stack: (0xc783be40 to 0xc783c000)
[ 1.418446] be40: 00000000 c04a34fc c04d3f00 c047d020 00000000 00000000 c04d3f4c c0343368
[ 1.426671] be60: c03f85f6 c04d3f50 00000000 c04a34fc c04d3f00 c047d020 00000068 c04d3f50
[ 1.434897] be80: c04d3f4c c047d074 ffffffff 00000000 c04c1b5c c04fffc4 c04c1b5c c049023c
[ 1.443121] bea0: 00000068 00000000 c783a038 c0343368 c041909f c783becc 00000020 c783becc
[ 1.451346] bec0: 00000000 c049031c c041909f 00000000 00000020 00000005 c049bbc8 c04a34fc
[ 1.459572] bee0: c04d3f00 c047d020 00000068 00000000 c783a038 c000869c c782b6a0 c00d89c0
[ 1.467797] bf00: c782b700 c782b6a0 00000000 c782b6a0 c034c50c c04f7914 00000000 c00d8c5c
[ 1.476023] bf20: 00000068 c060edf7 00000000 c0031dc8 60000053 c0457d84 c0457704 00000068
[ 1.484247] bf40: 00000005 00000005 00000001 00000005 c049bbc8 c04a34fc c04d3f00 c04d3f00
[ 1.492473] bf60: 00000068 c049bbd8 00000000 c047ab14 00000005 00000005 c047a478 c002f124
[ 1.500697] bf80: 00000000 00000000 00000000 c0340fb4 00000000 00000000 00000000 00000000
[ 1.508923] bfa0: 00000000 c0340fbc 00000000 c000e050 00000000 00000000 00000000 00000000
[ 1.517147] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.525373] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 1.533606] [<c047c998>] (unpack_to_rootfs+0xa8/0x2b0) from [<c047d074>] (populate_rootfs+0x54/0x224)
[ 1.542873] [<c047d074>] (populate_rootfs+0x54/0x224) from [<c000869c>] (do_one_initcall+0x94/0x13c)
[ 1.552055] [<c000869c>] (do_one_initcall+0x94/0x13c) from [<c047ab14>] (kernel_init_freeable+0xf8/0x1b8)
[ 1.561671] [<c047ab14>] (kernel_init_freeable+0xf8/0x1b8) from [<c0340fbc>] (kernel_init+0x8/0x100)
[ 1.570852] [<c0340fbc>] (kernel_init+0x8/0x100) from [<c000e050>] (ret_from_fork+0x14/0x24)
[ 1.579339] Code: 1a000056 e3550000 0a000054 e1c7a1d0 (e5d63000)
[ 1.585525] ---[ end trace 4e31448959d8cde7 ]---
[ 1.590212] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 1.590212]
next prev parent reply other threads:[~2014-01-10 14:09 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-06 23:47 [PATCH RFC RFT 0/2] ARM: Kirkwood: Synology DT files Andrew Lunn
2014-01-06 23:47 ` Andrew Lunn
[not found] ` <1389052027-16819-1-git-send-email-andrew-g2DYL2Zd6BY@public.gmane.org>
2014-01-06 23:47 ` [PATCH RFC RFT 1/2] Power: Reset: Generalize qnap-poweroff to with on Synology devices Andrew Lunn
2014-01-06 23:47 ` Andrew Lunn
2014-01-06 23:47 ` [PATCH RFC RFT 2/2] ARM: Kirkwood: Add support for many Synology NAS devices Andrew Lunn
2014-01-06 23:47 ` Andrew Lunn
2014-01-09 2:05 ` Ben Peddell
2014-01-09 2:05 ` Ben Peddell
2014-01-09 5:18 ` [PATCH RFC RFT 0/2] ARM: Kirkwood: Synology DT files Ben Peddell
2014-01-09 5:18 ` Ben Peddell
[not found] ` <52CE312B.3060108-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-01-09 16:55 ` Andrew Lunn
2014-01-09 16:55 ` Andrew Lunn
[not found] ` <20140109165557.GB9681-g2DYL2Zd6BY@public.gmane.org>
2014-01-10 1:01 ` Ben Peddell
2014-01-10 1:01 ` Ben Peddell
[not found] ` <52CF4652.3030207-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-01-10 11:28 ` Russell King - ARM Linux
2014-01-10 11:28 ` Russell King - ARM Linux
[not found] ` <20140110112846.GG27432-l+eeeJia6m9vn6HldHNs0ANdhmdF6hFW@public.gmane.org>
2014-01-10 14:09 ` Ben Peddell [this message]
2014-01-10 14:09 ` Ben Peddell
[not found] ` <52CFFF07.5080806-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-01-10 14:25 ` Andrew Lunn
2014-01-10 14:25 ` Andrew Lunn
[not found] ` <20140110142548.GG9681-g2DYL2Zd6BY@public.gmane.org>
2014-01-10 14:37 ` Sebastian Hesselbarth
2014-01-10 14:37 ` Sebastian Hesselbarth
2014-01-10 14:38 ` Ben Peddell
2014-01-10 14:38 ` Ben Peddell
2014-01-10 14:43 ` Andrew Lunn
2014-01-10 14:43 ` Andrew Lunn
[not found] ` <20140110144346.GH9681-g2DYL2Zd6BY@public.gmane.org>
2014-01-10 15:10 ` Ben Peddell
2014-01-10 15:10 ` Ben Peddell
2014-01-10 14:58 ` Russell King - ARM Linux
2014-01-10 14:58 ` Russell King - ARM Linux
[not found] ` <20140110145841.GF15937-l+eeeJia6m9vn6HldHNs0ANdhmdF6hFW@public.gmane.org>
2014-01-10 15:48 ` Ben Peddell
2014-01-10 15:48 ` Ben Peddell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52CFFF07.5080806@killerwolves.net \
--to=klightspeed-aslsrjg9ejhwx4hkxwhrhw@public.gmane.org \
--cc=andrew-g2DYL2Zd6BY@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=jason-NLaQJdtUoK4Be96aLqz0jA@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.