From: Geert Uytterhoeven <geert+renesas@glider.be> To: Magnus Damm <magnus.damm@gmail.com> Cc: linux-renesas-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org, Geert Uytterhoeven <geert+renesas@glider.be> Subject: [PATCH v3 2/2] arm64: dts: renesas: r8a779g0: Add remaining HSCIF nodes Date: Fri, 21 Oct 2022 16:13:05 +0200 [thread overview] Message-ID: <64c15b2d13439b2072cde0b588a251cb54f7dc01.1666361314.git.geert+renesas@glider.be> (raw) In-Reply-To: <cover.1666361314.git.geert+renesas@glider.be> Add device nodes for the remaining High Speed Serial Communication Interfaces with FIFO (HSCIF) on the Renesas R-Car V4H (R8A779G0) SoC, including DMA support. Reformat the existing HSCIF0 node for consistency. Based on patches in the BSP by Takeshi Kihara and Vinh Nguyen. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- v3: - No changes, v2: - Replace S0D3_PER by SASYNCPERD1, as per R-Car V4H Hardware User's Manual rev. 0.54. --- arch/arm64/boot/dts/renesas/r8a779g0.dtsi | 56 +++++++++++++++++++++-- 1 file changed, 53 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi index 8023bada93493100..8141ffc38a08301d 100644 --- a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi @@ -355,9 +355,8 @@ i2c5: i2c@e66e0000 { hscif0: serial@e6540000 { compatible = "renesas,hscif-r8a779g0", - "renesas,rcar-gen4-hscif", - "renesas,hscif"; - reg = <0 0xe6540000 0 96>; + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6540000 0 0x60>; interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 514>, <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, @@ -371,6 +370,57 @@ hscif0: serial@e6540000 { status = "disabled"; }; + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6550000 0 0x60>; + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x33>, <&dmac0 0x32>, + <&dmac1 0x33>, <&dmac1 0x32>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 515>; + status = "disabled"; + }; + + hscif2: serial@e6560000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6560000 0 0x60>; + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 516>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x35>, <&dmac0 0x34>, + <&dmac1 0x35>, <&dmac1 0x34>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 516>; + status = "disabled"; + }; + + hscif3: serial@e66a0000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe66a0000 0 0x60>; + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 517>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x37>, <&dmac0 0x36>, + <&dmac1 0x37>, <&dmac1 0x36>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 517>; + status = "disabled"; + }; + avb0: ethernet@e6800000 { compatible = "renesas,etheravb-r8a779g0", "renesas,etheravb-rcar-gen4"; -- 2.25.1
WARNING: multiple messages have this Message-ID (diff)
From: Geert Uytterhoeven <geert+renesas@glider.be> To: Magnus Damm <magnus.damm@gmail.com> Cc: linux-renesas-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org, Geert Uytterhoeven <geert+renesas@glider.be> Subject: [PATCH v3 2/2] arm64: dts: renesas: r8a779g0: Add remaining HSCIF nodes Date: Fri, 21 Oct 2022 16:13:05 +0200 [thread overview] Message-ID: <64c15b2d13439b2072cde0b588a251cb54f7dc01.1666361314.git.geert+renesas@glider.be> (raw) In-Reply-To: <cover.1666361314.git.geert+renesas@glider.be> Add device nodes for the remaining High Speed Serial Communication Interfaces with FIFO (HSCIF) on the Renesas R-Car V4H (R8A779G0) SoC, including DMA support. Reformat the existing HSCIF0 node for consistency. Based on patches in the BSP by Takeshi Kihara and Vinh Nguyen. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- v3: - No changes, v2: - Replace S0D3_PER by SASYNCPERD1, as per R-Car V4H Hardware User's Manual rev. 0.54. --- arch/arm64/boot/dts/renesas/r8a779g0.dtsi | 56 +++++++++++++++++++++-- 1 file changed, 53 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi index 8023bada93493100..8141ffc38a08301d 100644 --- a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi @@ -355,9 +355,8 @@ i2c5: i2c@e66e0000 { hscif0: serial@e6540000 { compatible = "renesas,hscif-r8a779g0", - "renesas,rcar-gen4-hscif", - "renesas,hscif"; - reg = <0 0xe6540000 0 96>; + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6540000 0 0x60>; interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cpg CPG_MOD 514>, <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, @@ -371,6 +370,57 @@ hscif0: serial@e6540000 { status = "disabled"; }; + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6550000 0 0x60>; + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 515>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x33>, <&dmac0 0x32>, + <&dmac1 0x33>, <&dmac1 0x32>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 515>; + status = "disabled"; + }; + + hscif2: serial@e6560000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe6560000 0 0x60>; + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 516>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x35>, <&dmac0 0x34>, + <&dmac1 0x35>, <&dmac1 0x34>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 516>; + status = "disabled"; + }; + + hscif3: serial@e66a0000 { + compatible = "renesas,hscif-r8a779g0", + "renesas,rcar-gen4-hscif", "renesas,hscif"; + reg = <0 0xe66a0000 0 0x60>; + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 517>, + <&cpg CPG_CORE R8A779G0_CLK_SASYNCPERD1>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac0 0x37>, <&dmac0 0x36>, + <&dmac1 0x37>, <&dmac1 0x36>; + dma-names = "tx", "rx", "tx", "rx"; + power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>; + resets = <&cpg 517>; + status = "disabled"; + }; + avb0: ethernet@e6800000 { compatible = "renesas,etheravb-r8a779g0", "renesas,etheravb-rcar-gen4"; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-10-21 14:13 UTC|newest] Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top 2022-10-21 14:13 [PATCH v3 0/2] arm64: dts: renesas: r8a779g0: Add remaining (H)SCIF nodes Geert Uytterhoeven 2022-10-21 14:13 ` Geert Uytterhoeven 2022-10-21 14:13 ` [PATCH v3 1/2] arm64: dts: renesas: r8a779g0: Add SCIF nodes Geert Uytterhoeven 2022-10-21 14:13 ` Geert Uytterhoeven 2022-10-21 22:46 ` Wolfram Sang 2022-10-21 22:46 ` Wolfram Sang 2022-10-21 14:13 ` Geert Uytterhoeven [this message] 2022-10-21 14:13 ` [PATCH v3 2/2] arm64: dts: renesas: r8a779g0: Add remaining HSCIF nodes Geert Uytterhoeven 2022-10-21 22:48 ` Wolfram Sang 2022-10-21 22:48 ` Wolfram Sang
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=64c15b2d13439b2072cde0b588a251cb54f7dc01.1666361314.git.geert+renesas@glider.be \ --to=geert+renesas@glider.be \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-renesas-soc@vger.kernel.org \ --cc=magnus.damm@gmail.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.