Re: [PATCH v3 00/10] AM642-EVM: Add USB support

From: Aswath Govindraju <a-govindraju@ti.com>
To: Praneeth Bajjuri <praneeth@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>,
	Lokesh Vutla <lokeshvutla@ti.com>,
	 Dave Gerlach <d-gerlach@ti.com>, Nishanth Menon <nm@ti.com>,
	Vignesh Raghavendra <vigneshr@ti.com>, Suman Anna <s-anna@ti.com>,
	Keerthy <j-keerthy@ti.com>, <u-boot@lists.denx.de>
Subject: Re: [PATCH v3 00/10] AM642-EVM: Add USB support
Date: Fri, 4 Jun 2021 22:19:31 +0530	[thread overview]
Message-ID: <6c6264e0-ab5e-0246-4949-61249a350e1c@ti.com> (raw)
In-Reply-To: <ec8ea665-16bf-d6b8-c84d-e727e556367b@ti.com>

Hi Praneeth,

On 04/06/21 10:18 pm, Praneeth Bajjuri wrote:
> 
> 
> On 6/4/21 11:30 AM, Aswath Govindraju wrote:
>> The following series of patches add support for the following
>> - Kconfig symbol for giving the load address for ATF
>> - USB Mass storage boot mode in AM642-EVM
>> - DFU boot mode in AM642-EVM
>> - Host and peripheral modes for AM642-EVM in U-Boot
>> - Set the USB PHY core voltage to 0.85V
>>
>> changes since v2,
>> - Increased the max size of ATF in patch 9
> 
> Please confirm if this is tested on ATF 2.5 too.
> 

Sorry, for not mentioning it.

Yes, this series was tested using ATF 2.5.

Thanks,
Aswath

> 
>> - Added reviewed-by from Suman Anna in patch 1
>> - Reworded the subject of patch 8
>>
>> changes since v1,
>> - Corrected the default load address of ATF to
>>    0x70000000
>>
>> Aswath Govindraju (10):
>>    tools: k3_fit_atf: Add support for providing ATF load address using a
>>      Kconfig symbol
>>    arm: mach-k3: am642_init: Add support for USB boot mode
>>    arm: mach-k3: am642_init: Do USB fixups to facilitate host and device
>>      boot modes
>>    board: ti: am64x: Set the core voltage of USB PHY to 0.85V
>>    arm: dts: k3-am64-main: Add USB DT nodes
>>    arm: dts: k3-am642-*-evm: Add USB support
>>    arm: dts: k3-am642-evm-u-boot: Add U-Boot tags and fix the dr_mode to
>>      peripheral for USB subsystem
>>    configs: am64x_evm_*_defconfig: Rearrange the components in SRAM to
>>      satisfy the limitations for USB DFU boot mode
>>    arm: dts: k3-am64-main: Update the location of ATF in SRAM and
>>      increase its max size
>>    configs: am64: Enable configs to support USB host and device modes
>>
>>   arch/arm/dts/k3-am64-main.dtsi                | 32 ++++++++++++-
>>   arch/arm/dts/k3-am642-evm-u-boot.dtsi         | 13 ++++++
>>   arch/arm/dts/k3-am642-evm.dts                 | 18 ++++++++
>>   arch/arm/dts/k3-am642-r5-evm.dts              | 18 ++++++++
>>   arch/arm/mach-k3/Kconfig                      |  7 +++
>>   arch/arm/mach-k3/am642_init.c                 | 46 ++++++++++++++++++-
>>   arch/arm/mach-k3/config.mk                    |  1 +
>>   arch/arm/mach-k3/include/mach/am64_hardware.h | 11 +++--
>>   arch/arm/mach-k3/include/mach/am64_spl.h      |  6 ++-
>>   board/ti/am64x/evm.c                          | 14 ++++++
>>   configs/am64x_evm_a53_defconfig               | 40 ++++++++++++++++
>>   configs/am64x_evm_r5_defconfig                | 38 +++++++++++++--
>>   include/configs/am64x_evm.h                   | 15 +++++-
>>   tools/k3_fit_atf.sh                           |  9 ++--
>>   14 files changed, 251 insertions(+), 17 deletions(-)
>>