From: Vimal Singh <vimal.newwork@gmail.com> To: Sukumar Ghorai <s-ghorai@ti.com> Cc: linux-omap@vger.kernel.org, linux-mtd@lists.infradead.org, tony@atomide.com, sakoman@gmail.com, mike@compulab.co.il, Artem.Bityutskiy@nokia.com Subject: Re: [PATCH v3 1/3] omap3 gpmc: functionality enhancement Date: Wed, 19 May 2010 20:16:43 +0530 [thread overview] Message-ID: <AANLkTikFxtzDpiJvJjnuonM2urMJR1LDLafx5JtpC_bS@mail.gmail.com> (raw) In-Reply-To: <1274181389-7488-2-git-send-email-s-ghorai@ti.com> On Tue, May 18, 2010 at 4:46 PM, Sukumar Ghorai <s-ghorai@ti.com> wrote: > few functions added in gpmc module and to be used by other drivers like NAND. > E.g.: - ioctl function > - ecc functions > > Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> > --- > arch/arm/mach-omap2/gpmc.c | 246 +++++++++++++++++++++++++++++++- > arch/arm/plat-omap/include/plat/gpmc.h | 35 ++++- > drivers/mtd/nand/omap2.c | 4 +- > 3 files changed, 274 insertions(+), 11 deletions(-) > > diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c > index 5bc3ca0..7e6d821 > --- a/arch/arm/mach-omap2/gpmc.c > +++ b/arch/arm/mach-omap2/gpmc.c > @@ -46,8 +46,9 @@ > #define GPMC_ECC_CONFIG 0x1f4 > #define GPMC_ECC_CONTROL 0x1f8 > #define GPMC_ECC_SIZE_CONFIG 0x1fc > +#define GPMC_ECC1_RESULT 0x200 > > -#define GPMC_CS0 0x60 > +#define GPMC_CS0_BASE 0x60 > #define GPMC_CS_SIZE 0x30 > > #define GPMC_MEM_START 0x00000000 > @@ -92,7 +93,9 @@ struct omap3_gpmc_regs { > static struct resource gpmc_mem_root; > static struct resource gpmc_cs_mem[GPMC_CS_NUM]; > static DEFINE_SPINLOCK(gpmc_mem_lock); > -static unsigned gpmc_cs_map; > +static unsigned int gpmc_cs_map; /* flag for cs which are initialized */ > +static int gpmc_pref_used = -EINVAL; /* cs using prefetch engine */ > +static int gpmc_ecc_used = -EINVAL; /* cs using ecc engine */ > > static void __iomem *gpmc_base; > > @@ -108,11 +111,27 @@ static u32 gpmc_read_reg(int idx) > return __raw_readl(gpmc_base + idx); > } > > +static void gpmc_cs_write_byte(int cs, int idx, u8 val) > +{ > + void __iomem *reg_addr; > + > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > + __raw_writeb(val, reg_addr); > +} > + > +static u8 gpmc_cs_read_byte(int cs, int idx) > +{ > + void __iomem *reg_addr; > + > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > + return __raw_readb(reg_addr); > +} > + > void gpmc_cs_write_reg(int cs, int idx, u32 val) > { > void __iomem *reg_addr; > > - reg_addr = gpmc_base + GPMC_CS0 + (cs * GPMC_CS_SIZE) + idx; > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > __raw_writel(val, reg_addr); > } > > @@ -120,7 +139,7 @@ u32 gpmc_cs_read_reg(int cs, int idx) > { > void __iomem *reg_addr; > > - reg_addr = gpmc_base + GPMC_CS0 + (cs * GPMC_CS_SIZE) + idx; > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > return __raw_readl(reg_addr); > } > > @@ -419,8 +438,100 @@ void gpmc_cs_free(int cs) > EXPORT_SYMBOL(gpmc_cs_free); > > /** > + * gpmc_hwcontrol - hardware specific access (read/ write) control > + * @cs: chip select number > + * @cmd: command type > + * @write: 1 for write; 0 for read > + * @wval: value to write > + * @rval: read pointer > + */ > +int gpmc_hwcontrol(int cs, int cmd, int write, int wval, int *rval) > +{ > + u32 regval = 0; > + > + if (!write && !rval) > + return -EINVAL; > + > + switch (cmd) { > + case GPMC_STATUS_BUFFER: > + regval = gpmc_read_reg(GPMC_STATUS); > + /* 1 : buffer is available to write */ > + *rval = regval & GPMC_STATUS_BUFF_EMPTY; > + break; > + > + case GPMC_GET_SET_IRQ_STATUS: > + if (write) > + gpmc_write_reg(GPMC_IRQSTATUS, wval); > + else > + *rval = gpmc_read_reg(GPMC_IRQSTATUS); > + break; > + > + case GPMC_PREFETCH_FIFO_CNT: > + regval = gpmc_read_reg(GPMC_PREFETCH_STATUS); > + *rval = GPMC_PREFETCH_STATUS_FIFO_CNT(regval); > + break; > + > + case GPMC_PREFETCH_COUNT: > + regval = gpmc_read_reg(GPMC_PREFETCH_STATUS); > + *rval = GPMC_PREFETCH_STATUS_COUNT(regval); > + break; > + > + case GPMC_CONFIG_WP: > + regval = gpmc_read_reg(GPMC_CONFIG); > + if (wval) > + regval &= ~GPMC_CONFIG_WRITEPROTECT; /* WP is ON */ > + else > + regval |= GPMC_CONFIG_WRITEPROTECT; /* WP is OFF */ > + gpmc_write_reg(GPMC_CONFIG, regval); > + break; > + > + case GPMC_CONFIG_RDY_BSY: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= WR_RD_PIN_MONITORING; > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; IIRC, at least in OMAP2/3, ready/busy pin is not in use (not connected). > + > + case GPMC_CONFIG_DEV_SIZE: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= GPMC_CONFIG1_DEVICESIZE(wval); > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; > + > + case GPMC_CONFIG_DEV_TYPE: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= GPMC_CONFIG1_DEVICETYPE(wval); > + if (wval == GPMC_DEVICETYPE_NOR) > + regval |= GPMC_CONFIG1_MUXADDDATA; > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; > + > + case GPMC_NAND_COMMAND: > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_COMMAND, wval); > + break; > + > + case GPMC_NAND_ADDRESS: > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_ADDRESS, wval); > + break; > + > + case GPMC_NAND_DATA: > + if (write) > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_DATA, wval); > + else > + *rval = gpmc_cs_read_byte(cs, GPMC_CS_NAND_DATA); > + break; > + > + default: > + printk(KERN_ERR "gpmc_hwcontrol: Not supported\n"); > + return -EINVAL; > + } > + > + return 0; > +} > +EXPORT_SYMBOL(gpmc_hwcontrol); > + > +/** > * gpmc_prefetch_enable - configures and starts prefetch transfer > - * @cs: nand cs (chip select) number > + * @cs: cs (chip select) number > * @dma_mode: dma mode enable (1) or disable (0) > * @u32_count: number of bytes to be transferred > * @is_write: prefetch read(0) or write post(1) mode > @@ -430,6 +541,11 @@ int gpmc_prefetch_enable(int cs, int dma_mode, > { > uint32_t prefetch_config1; > > + if (gpmc_pref_used == -EINVAL) > + gpmc_pref_used = cs; > + else > + return -EBUSY; This is not required. Prefetch engine has just one instance > + > if (!(gpmc_read_reg(GPMC_PREFETCH_CONTROL))) { and any prefetch request will be done only if above check passes. Which actually checks if 'prefetch' is busy or not. You can see in NAND driver (omap2.c) code, it understands that. > /* Set the amount of bytes to be prefetched */ > gpmc_write_reg(GPMC_PREFETCH_CONFIG2, u32_count); > @@ -456,13 +572,20 @@ EXPORT_SYMBOL(gpmc_prefetch_enable); > /** > * gpmc_prefetch_reset - disables and stops the prefetch engine > */ > -void gpmc_prefetch_reset(void) > +int gpmc_prefetch_reset(int cs) > { > + if (gpmc_pref_used == cs) > + gpmc_pref_used = -EINVAL; > + else > + return -EINVAL; > + This is also not required. As, this function will be called only if prefetch was used. > /* Stop the PFPW engine */ > gpmc_write_reg(GPMC_PREFETCH_CONTROL, 0x0); > > /* Reset/disable the PFPW engine */ > gpmc_write_reg(GPMC_PREFETCH_CONFIG1, 0x0); > + > + return 0; > } > EXPORT_SYMBOL(gpmc_prefetch_reset); > > @@ -615,3 +738,114 @@ void omap3_gpmc_restore_context(void) > } > } > #endif /* CONFIG_ARCH_OMAP3 */ > + > +/** > + * gpmc_ecc_init - initialize hw ecc for device in GPMC controller > + * @cs: chip select number > + * @ecc_size: number of bytes for ecc generation > + */ > + > +int gpmc_ecc_init(int cs, int ecc_size) > +{ > + unsigned int val = 0x0; > + > + /* check if ecc engine already by another cs */ > + if (gpmc_ecc_used == -EINVAL) > + gpmc_ecc_used = cs; > + else > + return -EBUSY; Here few things need be to consider: 1. 'init' is supposed to done once for every instance of driver during probe 2. But ECC engine, too, have only one instance at a time, So 3. As long as all NAND chip are supposed to use same ECC machenism, we can go for only one time 'init' for all drivers, perhaps in gpmc_nand.c. 4. But in case, different instances of driver (or NAND chip) requires different ECC machenism (for ex. Hamming or BCH, or even with different capabilities of error correction), this will no longer vailid. Then rather we should have something like 'gpmc_ecc_config' call to configer ECC engine for everytime a driver needs it (something like as it is done for prefetch engine). > + > + /* read ecc control register */ > + val = gpmc_read_reg(GPMC_ECC_CONTROL); > + > + /* clear ecc and enable bits */ > + val = ((0x00000001<<8) | 0x00000001); > + gpmc_write_reg(GPMC_ECC_CONTROL, val); > + > + /* Read from ECC Size Config Register */ > + val = gpmc_read_reg(GPMC_ECC_SIZE_CONFIG); > + > + /* program ecc and result sizes */ > + val = ((((ecc_size >> 1) - 1) << 22) | (0x0000000F)); > + gpmc_write_reg(GPMC_ECC_SIZE_CONFIG, val); > + > + return 0; > +} > + > +/** > + * gpmc_calculate_ecc - generate non-inverted ecc bytes > + * @cs: chip select number > + * @dat: data pointer over which ecc is computed > + * @ecc_code: ecc code buffer > + * > + * Using non-inverted ECC is considered ugly since writing a blank > + * page (padding) will clear the ECC bytes. This is not a problem as long > + * no one is trying to write data on the seemingly unused page. Reading > + * an erased page will produce an ECC mismatch between generated and read > + * ECC bytes that has to be dealt with separately. > + */ > +int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code) > +{ > + unsigned int val = 0x0; > + > + if (gpmc_ecc_used != cs) > + return -EINVAL; > + > + /* read ecc result */ > + val = gpmc_read_reg(GPMC_ECC1_RESULT); > + *ecc_code++ = val; /* P128e, ..., P1e */ > + *ecc_code++ = val >> 16; /* P128o, ..., P1o */ > + /* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */ > + *ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0); > + > + return 0; > +} > + > +/** > + * gpmc_enable_hwecc - enable hardware ecc functionality > + * @cs: chip select number > + * @mode: read/write mode > + * @dev_width: device bus width(1 for x16, 0 for x8) > + */ > +int gpmc_enable_hwecc(int cs, int mode, int dev_width) > +{ > + unsigned int val; > + > + if (gpmc_ecc_used != cs) > + return -EINVAL; > + > + switch (mode) { > + case GPMC_ECC_READ: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x101); > + break; > + case GPMC_ECC_READSYN: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x100); > + break; > + case GPMC_ECC_WRITE: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x101); > + break; > + default: > + printk(KERN_INFO "Error: Unrecognized Mode[%d]!\n", mode); > + break; > + } > + > + /* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */ > + val = (dev_width << 7) | (cs << 1) | (0x1); > + gpmc_write_reg(GPMC_ECC_CONFIG, val); > + return 0; > +} > + > +/** > + * gmpc_ecc_reset - release the HW ECC in GPMC controller > + * @cs: Chip select number > + */ > +int gpmc_ecc_reset(int cs) > +{ > + if (gpmc_ecc_used == cs) > + gpmc_ecc_used = -EINVAL; > + else > + return -EINVAL; > + > + return 0; > +} > + > diff --git a/arch/arm/plat-omap/include/plat/gpmc.h b/arch/arm/plat-omap/include/plat/gpmc.h > index 145838a..67a3442 > --- a/arch/arm/plat-omap/include/plat/gpmc.h > +++ b/arch/arm/plat-omap/include/plat/gpmc.h > @@ -27,8 +27,24 @@ > > #define GPMC_CONFIG 0x50 > #define GPMC_STATUS 0x54 > -#define GPMC_CS0_BASE 0x60 > -#define GPMC_CS_SIZE 0x30 > + > +/* Control Commands */ > +#define GPMC_CONFIG_WP 0x00000001 > +#define GPMC_CONFIG_RDY_BSY 0x00000002 > +#define GPMC_CONFIG_DEV_SIZE 0x00000003 > +#define GPMC_CONFIG_DEV_TYPE 0x00000004 > +#define GPMC_NAND_COMMAND 0x00000005 > +#define GPMC_NAND_ADDRESS 0x00000006 > +#define GPMC_NAND_DATA 0x00000007 > +#define GPMC_STATUS_BUFFER 0x00000008 /* 1: buffer is available to write */ > +#define GPMC_PREFETCH_FIFO_CNT 0x00000009 /* bytes available in FIFO for r/w */ > +#define GPMC_PREFETCH_COUNT 0x0000000A /* remaining bytes to be read/write*/ > +#define GPMC_GET_SET_IRQ_STATUS 0x0000000B > + > +/* ECC commands */ > +#define GPMC_ECC_READ 0 /* Reset Hardware ECC for read */ > +#define GPMC_ECC_WRITE 1 /* Reset Hardware ECC for write */ > +#define GPMC_ECC_READSYN 2 /* Reset before syndrom is read back */ > > #define GPMC_CONFIG1_WRAPBURST_SUPP (1 << 31) > #define GPMC_CONFIG1_READMULTIPLE_SUPP (1 << 30) > @@ -56,6 +72,14 @@ > #define GPMC_CONFIG1_FCLK_DIV4 (GPMC_CONFIG1_FCLK_DIV(3)) > #define GPMC_CONFIG7_CSVALID (1 << 6) > > +#define GPMC_DEVICETYPE_NOR 0 > +#define GPMC_DEVICETYPE_NAND 2 > +#define GPMC_CONFIG_WRITEPROTECT 0x00000010 > +#define GPMC_STATUS_BUFF_EMPTY 0x00000001 > +#define WR_RD_PIN_MONITORING 0x00600000 > +#define GPMC_PREFETCH_STATUS_FIFO_CNT(val) ((val & 0x7f000000) >> 24) > +#define GPMC_PREFETCH_STATUS_COUNT(val) (val & 0x00003fff) > + > /* > * Note that all values in this struct are in nanoseconds, while > * the register values are in gpmc_fck cycles. > @@ -108,10 +132,15 @@ extern int gpmc_cs_set_reserved(int cs, int reserved); > extern int gpmc_cs_reserved(int cs); > extern int gpmc_prefetch_enable(int cs, int dma_mode, > unsigned int u32_count, int is_write); > -extern void gpmc_prefetch_reset(void); > +extern int gpmc_prefetch_reset(int cs); > extern int gpmc_prefetch_status(void); > extern void omap3_gpmc_save_context(void); > extern void omap3_gpmc_restore_context(void); > extern void gpmc_init(void); > +extern int gpmc_hwcontrol(int cs, int cmd, int write, int wval, int *rval); > > +int gpmc_ecc_init(int cs, int ecc_size); > +int gpmc_enable_hwecc(int cs, int mode, int dev_width); > +int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code); > +int gpmc_ecc_reset(int cs); > #endif > diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c > index 7545568..206406b > --- a/drivers/mtd/nand/omap2.c > +++ b/drivers/mtd/nand/omap2.c > @@ -316,7 +316,7 @@ static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len) > } while (len); > > /* disable and stop the PFPW engine */ > - gpmc_prefetch_reset(); > + gpmc_prefetch_reset(info->gpmc_cs); Not required. see above comments. > } > } > > @@ -360,7 +360,7 @@ static void omap_write_buf_pref(struct mtd_info *mtd, > } > > /* disable and stop the PFPW engine */ > - gpmc_prefetch_reset(); > + gpmc_prefetch_reset(info->gpmc_cs); Not required. see above comments. > } > } > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- Regards, Vimal Singh -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
WARNING: multiple messages have this Message-ID (diff)
From: Vimal Singh <vimal.newwork@gmail.com> To: Sukumar Ghorai <s-ghorai@ti.com> Cc: Artem.Bityutskiy@nokia.com, tony@atomide.com, sakoman@gmail.com, linux-mtd@lists.infradead.org, linux-omap@vger.kernel.org Subject: Re: [PATCH v3 1/3] omap3 gpmc: functionality enhancement Date: Wed, 19 May 2010 20:16:43 +0530 [thread overview] Message-ID: <AANLkTikFxtzDpiJvJjnuonM2urMJR1LDLafx5JtpC_bS@mail.gmail.com> (raw) In-Reply-To: <1274181389-7488-2-git-send-email-s-ghorai@ti.com> On Tue, May 18, 2010 at 4:46 PM, Sukumar Ghorai <s-ghorai@ti.com> wrote: > few functions added in gpmc module and to be used by other drivers like NAND. > E.g.: - ioctl function > - ecc functions > > Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> > --- > arch/arm/mach-omap2/gpmc.c | 246 +++++++++++++++++++++++++++++++- > arch/arm/plat-omap/include/plat/gpmc.h | 35 ++++- > drivers/mtd/nand/omap2.c | 4 +- > 3 files changed, 274 insertions(+), 11 deletions(-) > > diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c > index 5bc3ca0..7e6d821 > --- a/arch/arm/mach-omap2/gpmc.c > +++ b/arch/arm/mach-omap2/gpmc.c > @@ -46,8 +46,9 @@ > #define GPMC_ECC_CONFIG 0x1f4 > #define GPMC_ECC_CONTROL 0x1f8 > #define GPMC_ECC_SIZE_CONFIG 0x1fc > +#define GPMC_ECC1_RESULT 0x200 > > -#define GPMC_CS0 0x60 > +#define GPMC_CS0_BASE 0x60 > #define GPMC_CS_SIZE 0x30 > > #define GPMC_MEM_START 0x00000000 > @@ -92,7 +93,9 @@ struct omap3_gpmc_regs { > static struct resource gpmc_mem_root; > static struct resource gpmc_cs_mem[GPMC_CS_NUM]; > static DEFINE_SPINLOCK(gpmc_mem_lock); > -static unsigned gpmc_cs_map; > +static unsigned int gpmc_cs_map; /* flag for cs which are initialized */ > +static int gpmc_pref_used = -EINVAL; /* cs using prefetch engine */ > +static int gpmc_ecc_used = -EINVAL; /* cs using ecc engine */ > > static void __iomem *gpmc_base; > > @@ -108,11 +111,27 @@ static u32 gpmc_read_reg(int idx) > return __raw_readl(gpmc_base + idx); > } > > +static void gpmc_cs_write_byte(int cs, int idx, u8 val) > +{ > + void __iomem *reg_addr; > + > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > + __raw_writeb(val, reg_addr); > +} > + > +static u8 gpmc_cs_read_byte(int cs, int idx) > +{ > + void __iomem *reg_addr; > + > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > + return __raw_readb(reg_addr); > +} > + > void gpmc_cs_write_reg(int cs, int idx, u32 val) > { > void __iomem *reg_addr; > > - reg_addr = gpmc_base + GPMC_CS0 + (cs * GPMC_CS_SIZE) + idx; > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > __raw_writel(val, reg_addr); > } > > @@ -120,7 +139,7 @@ u32 gpmc_cs_read_reg(int cs, int idx) > { > void __iomem *reg_addr; > > - reg_addr = gpmc_base + GPMC_CS0 + (cs * GPMC_CS_SIZE) + idx; > + reg_addr = gpmc_base + GPMC_CS0_BASE + (cs * GPMC_CS_SIZE) + idx; > return __raw_readl(reg_addr); > } > > @@ -419,8 +438,100 @@ void gpmc_cs_free(int cs) > EXPORT_SYMBOL(gpmc_cs_free); > > /** > + * gpmc_hwcontrol - hardware specific access (read/ write) control > + * @cs: chip select number > + * @cmd: command type > + * @write: 1 for write; 0 for read > + * @wval: value to write > + * @rval: read pointer > + */ > +int gpmc_hwcontrol(int cs, int cmd, int write, int wval, int *rval) > +{ > + u32 regval = 0; > + > + if (!write && !rval) > + return -EINVAL; > + > + switch (cmd) { > + case GPMC_STATUS_BUFFER: > + regval = gpmc_read_reg(GPMC_STATUS); > + /* 1 : buffer is available to write */ > + *rval = regval & GPMC_STATUS_BUFF_EMPTY; > + break; > + > + case GPMC_GET_SET_IRQ_STATUS: > + if (write) > + gpmc_write_reg(GPMC_IRQSTATUS, wval); > + else > + *rval = gpmc_read_reg(GPMC_IRQSTATUS); > + break; > + > + case GPMC_PREFETCH_FIFO_CNT: > + regval = gpmc_read_reg(GPMC_PREFETCH_STATUS); > + *rval = GPMC_PREFETCH_STATUS_FIFO_CNT(regval); > + break; > + > + case GPMC_PREFETCH_COUNT: > + regval = gpmc_read_reg(GPMC_PREFETCH_STATUS); > + *rval = GPMC_PREFETCH_STATUS_COUNT(regval); > + break; > + > + case GPMC_CONFIG_WP: > + regval = gpmc_read_reg(GPMC_CONFIG); > + if (wval) > + regval &= ~GPMC_CONFIG_WRITEPROTECT; /* WP is ON */ > + else > + regval |= GPMC_CONFIG_WRITEPROTECT; /* WP is OFF */ > + gpmc_write_reg(GPMC_CONFIG, regval); > + break; > + > + case GPMC_CONFIG_RDY_BSY: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= WR_RD_PIN_MONITORING; > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; IIRC, at least in OMAP2/3, ready/busy pin is not in use (not connected). > + > + case GPMC_CONFIG_DEV_SIZE: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= GPMC_CONFIG1_DEVICESIZE(wval); > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; > + > + case GPMC_CONFIG_DEV_TYPE: > + regval = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1); > + regval |= GPMC_CONFIG1_DEVICETYPE(wval); > + if (wval == GPMC_DEVICETYPE_NOR) > + regval |= GPMC_CONFIG1_MUXADDDATA; > + gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, regval); > + break; > + > + case GPMC_NAND_COMMAND: > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_COMMAND, wval); > + break; > + > + case GPMC_NAND_ADDRESS: > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_ADDRESS, wval); > + break; > + > + case GPMC_NAND_DATA: > + if (write) > + gpmc_cs_write_byte(cs, GPMC_CS_NAND_DATA, wval); > + else > + *rval = gpmc_cs_read_byte(cs, GPMC_CS_NAND_DATA); > + break; > + > + default: > + printk(KERN_ERR "gpmc_hwcontrol: Not supported\n"); > + return -EINVAL; > + } > + > + return 0; > +} > +EXPORT_SYMBOL(gpmc_hwcontrol); > + > +/** > * gpmc_prefetch_enable - configures and starts prefetch transfer > - * @cs: nand cs (chip select) number > + * @cs: cs (chip select) number > * @dma_mode: dma mode enable (1) or disable (0) > * @u32_count: number of bytes to be transferred > * @is_write: prefetch read(0) or write post(1) mode > @@ -430,6 +541,11 @@ int gpmc_prefetch_enable(int cs, int dma_mode, > { > uint32_t prefetch_config1; > > + if (gpmc_pref_used == -EINVAL) > + gpmc_pref_used = cs; > + else > + return -EBUSY; This is not required. Prefetch engine has just one instance > + > if (!(gpmc_read_reg(GPMC_PREFETCH_CONTROL))) { and any prefetch request will be done only if above check passes. Which actually checks if 'prefetch' is busy or not. You can see in NAND driver (omap2.c) code, it understands that. > /* Set the amount of bytes to be prefetched */ > gpmc_write_reg(GPMC_PREFETCH_CONFIG2, u32_count); > @@ -456,13 +572,20 @@ EXPORT_SYMBOL(gpmc_prefetch_enable); > /** > * gpmc_prefetch_reset - disables and stops the prefetch engine > */ > -void gpmc_prefetch_reset(void) > +int gpmc_prefetch_reset(int cs) > { > + if (gpmc_pref_used == cs) > + gpmc_pref_used = -EINVAL; > + else > + return -EINVAL; > + This is also not required. As, this function will be called only if prefetch was used. > /* Stop the PFPW engine */ > gpmc_write_reg(GPMC_PREFETCH_CONTROL, 0x0); > > /* Reset/disable the PFPW engine */ > gpmc_write_reg(GPMC_PREFETCH_CONFIG1, 0x0); > + > + return 0; > } > EXPORT_SYMBOL(gpmc_prefetch_reset); > > @@ -615,3 +738,114 @@ void omap3_gpmc_restore_context(void) > } > } > #endif /* CONFIG_ARCH_OMAP3 */ > + > +/** > + * gpmc_ecc_init - initialize hw ecc for device in GPMC controller > + * @cs: chip select number > + * @ecc_size: number of bytes for ecc generation > + */ > + > +int gpmc_ecc_init(int cs, int ecc_size) > +{ > + unsigned int val = 0x0; > + > + /* check if ecc engine already by another cs */ > + if (gpmc_ecc_used == -EINVAL) > + gpmc_ecc_used = cs; > + else > + return -EBUSY; Here few things need be to consider: 1. 'init' is supposed to done once for every instance of driver during probe 2. But ECC engine, too, have only one instance at a time, So 3. As long as all NAND chip are supposed to use same ECC machenism, we can go for only one time 'init' for all drivers, perhaps in gpmc_nand.c. 4. But in case, different instances of driver (or NAND chip) requires different ECC machenism (for ex. Hamming or BCH, or even with different capabilities of error correction), this will no longer vailid. Then rather we should have something like 'gpmc_ecc_config' call to configer ECC engine for everytime a driver needs it (something like as it is done for prefetch engine). > + > + /* read ecc control register */ > + val = gpmc_read_reg(GPMC_ECC_CONTROL); > + > + /* clear ecc and enable bits */ > + val = ((0x00000001<<8) | 0x00000001); > + gpmc_write_reg(GPMC_ECC_CONTROL, val); > + > + /* Read from ECC Size Config Register */ > + val = gpmc_read_reg(GPMC_ECC_SIZE_CONFIG); > + > + /* program ecc and result sizes */ > + val = ((((ecc_size >> 1) - 1) << 22) | (0x0000000F)); > + gpmc_write_reg(GPMC_ECC_SIZE_CONFIG, val); > + > + return 0; > +} > + > +/** > + * gpmc_calculate_ecc - generate non-inverted ecc bytes > + * @cs: chip select number > + * @dat: data pointer over which ecc is computed > + * @ecc_code: ecc code buffer > + * > + * Using non-inverted ECC is considered ugly since writing a blank > + * page (padding) will clear the ECC bytes. This is not a problem as long > + * no one is trying to write data on the seemingly unused page. Reading > + * an erased page will produce an ECC mismatch between generated and read > + * ECC bytes that has to be dealt with separately. > + */ > +int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code) > +{ > + unsigned int val = 0x0; > + > + if (gpmc_ecc_used != cs) > + return -EINVAL; > + > + /* read ecc result */ > + val = gpmc_read_reg(GPMC_ECC1_RESULT); > + *ecc_code++ = val; /* P128e, ..., P1e */ > + *ecc_code++ = val >> 16; /* P128o, ..., P1o */ > + /* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */ > + *ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0); > + > + return 0; > +} > + > +/** > + * gpmc_enable_hwecc - enable hardware ecc functionality > + * @cs: chip select number > + * @mode: read/write mode > + * @dev_width: device bus width(1 for x16, 0 for x8) > + */ > +int gpmc_enable_hwecc(int cs, int mode, int dev_width) > +{ > + unsigned int val; > + > + if (gpmc_ecc_used != cs) > + return -EINVAL; > + > + switch (mode) { > + case GPMC_ECC_READ: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x101); > + break; > + case GPMC_ECC_READSYN: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x100); > + break; > + case GPMC_ECC_WRITE: > + gpmc_write_reg(GPMC_ECC_CONTROL, 0x101); > + break; > + default: > + printk(KERN_INFO "Error: Unrecognized Mode[%d]!\n", mode); > + break; > + } > + > + /* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */ > + val = (dev_width << 7) | (cs << 1) | (0x1); > + gpmc_write_reg(GPMC_ECC_CONFIG, val); > + return 0; > +} > + > +/** > + * gmpc_ecc_reset - release the HW ECC in GPMC controller > + * @cs: Chip select number > + */ > +int gpmc_ecc_reset(int cs) > +{ > + if (gpmc_ecc_used == cs) > + gpmc_ecc_used = -EINVAL; > + else > + return -EINVAL; > + > + return 0; > +} > + > diff --git a/arch/arm/plat-omap/include/plat/gpmc.h b/arch/arm/plat-omap/include/plat/gpmc.h > index 145838a..67a3442 > --- a/arch/arm/plat-omap/include/plat/gpmc.h > +++ b/arch/arm/plat-omap/include/plat/gpmc.h > @@ -27,8 +27,24 @@ > > #define GPMC_CONFIG 0x50 > #define GPMC_STATUS 0x54 > -#define GPMC_CS0_BASE 0x60 > -#define GPMC_CS_SIZE 0x30 > + > +/* Control Commands */ > +#define GPMC_CONFIG_WP 0x00000001 > +#define GPMC_CONFIG_RDY_BSY 0x00000002 > +#define GPMC_CONFIG_DEV_SIZE 0x00000003 > +#define GPMC_CONFIG_DEV_TYPE 0x00000004 > +#define GPMC_NAND_COMMAND 0x00000005 > +#define GPMC_NAND_ADDRESS 0x00000006 > +#define GPMC_NAND_DATA 0x00000007 > +#define GPMC_STATUS_BUFFER 0x00000008 /* 1: buffer is available to write */ > +#define GPMC_PREFETCH_FIFO_CNT 0x00000009 /* bytes available in FIFO for r/w */ > +#define GPMC_PREFETCH_COUNT 0x0000000A /* remaining bytes to be read/write*/ > +#define GPMC_GET_SET_IRQ_STATUS 0x0000000B > + > +/* ECC commands */ > +#define GPMC_ECC_READ 0 /* Reset Hardware ECC for read */ > +#define GPMC_ECC_WRITE 1 /* Reset Hardware ECC for write */ > +#define GPMC_ECC_READSYN 2 /* Reset before syndrom is read back */ > > #define GPMC_CONFIG1_WRAPBURST_SUPP (1 << 31) > #define GPMC_CONFIG1_READMULTIPLE_SUPP (1 << 30) > @@ -56,6 +72,14 @@ > #define GPMC_CONFIG1_FCLK_DIV4 (GPMC_CONFIG1_FCLK_DIV(3)) > #define GPMC_CONFIG7_CSVALID (1 << 6) > > +#define GPMC_DEVICETYPE_NOR 0 > +#define GPMC_DEVICETYPE_NAND 2 > +#define GPMC_CONFIG_WRITEPROTECT 0x00000010 > +#define GPMC_STATUS_BUFF_EMPTY 0x00000001 > +#define WR_RD_PIN_MONITORING 0x00600000 > +#define GPMC_PREFETCH_STATUS_FIFO_CNT(val) ((val & 0x7f000000) >> 24) > +#define GPMC_PREFETCH_STATUS_COUNT(val) (val & 0x00003fff) > + > /* > * Note that all values in this struct are in nanoseconds, while > * the register values are in gpmc_fck cycles. > @@ -108,10 +132,15 @@ extern int gpmc_cs_set_reserved(int cs, int reserved); > extern int gpmc_cs_reserved(int cs); > extern int gpmc_prefetch_enable(int cs, int dma_mode, > unsigned int u32_count, int is_write); > -extern void gpmc_prefetch_reset(void); > +extern int gpmc_prefetch_reset(int cs); > extern int gpmc_prefetch_status(void); > extern void omap3_gpmc_save_context(void); > extern void omap3_gpmc_restore_context(void); > extern void gpmc_init(void); > +extern int gpmc_hwcontrol(int cs, int cmd, int write, int wval, int *rval); > > +int gpmc_ecc_init(int cs, int ecc_size); > +int gpmc_enable_hwecc(int cs, int mode, int dev_width); > +int gpmc_calculate_ecc(int cs, const u_char *dat, u_char *ecc_code); > +int gpmc_ecc_reset(int cs); > #endif > diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c > index 7545568..206406b > --- a/drivers/mtd/nand/omap2.c > +++ b/drivers/mtd/nand/omap2.c > @@ -316,7 +316,7 @@ static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len) > } while (len); > > /* disable and stop the PFPW engine */ > - gpmc_prefetch_reset(); > + gpmc_prefetch_reset(info->gpmc_cs); Not required. see above comments. > } > } > > @@ -360,7 +360,7 @@ static void omap_write_buf_pref(struct mtd_info *mtd, > } > > /* disable and stop the PFPW engine */ > - gpmc_prefetch_reset(); > + gpmc_prefetch_reset(info->gpmc_cs); Not required. see above comments. > } > } > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- Regards, Vimal Singh
next prev parent reply other threads:[~2010-05-19 14:47 UTC|newest] Thread overview: 159+ messages / expand[flat|nested] mbox.gz Atom feed top [not found] <Sukumar Ghorai <s-ghorai@ti.com> 2010-04-06 12:29 ` [PATCH 0/2] OMAP: Flash device support 3630 sdp board Sukumar Ghorai 2010-04-06 12:29 ` [PATCH 1/2] OMAP3630SDP: Add support for Flash Sukumar Ghorai 2010-04-06 12:29 ` [PATCH 2/2] OMAP3630SDP: enable Flash device support Sukumar Ghorai 2010-04-06 13:02 ` [PATCH 1/2] OMAP3630SDP: Add support for Flash Vimal Singh 2010-04-13 17:37 ` [PATCH] nand support on omap3 boards Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v3 1/8] omap3: zoom: Introducing 'board-zoom-flash.c' Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v3 2/8] omap3: add support for NAND on zoom2 board Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v3 3/8] omap3: add support for NAND on zoom3 board Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v2 4/8] omap-3630-sdp : Add support for Flash Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v2 5/8] omap-3630-sdp: enable Flash device support Sukumar Ghorai 2010-04-13 17:37 ` [PATCH v2 6/8] omap3: add support for NAND on LDP board Sukumar Ghorai 2010-04-13 17:37 ` [PATCH 7/8] zoom2: enable NAND support Sukumar Ghorai 2010-04-13 17:37 ` [PATCH 8/8] zoom3: " Sukumar Ghorai 2010-04-13 17:37 ` [PATCH] nand support on omap3 boards Sukumar Ghorai 2010-04-13 17:37 ` [PATCH 8/8] omap3: GPMC register definition at common location Sukumar Ghorai 2010-04-13 17:37 ` [PATCH] omap3: NAND Prefetch in IRQ mode support Sukumar Ghorai 2010-04-13 17:37 ` [PATCH] omap-3630 NAND: enable NAND io in prefetch-irq mode Sukumar Ghorai 2010-04-13 17:37 ` [PATCH] omap: NAND: ecc layout select from board file Sukumar Ghorai 2010-04-13 17:37 ` [PATCH] omap: NAND: Making ecc layout as compatible with romcode ecc Sukumar Ghorai 2010-04-14 4:35 ` [PATCH] nand support on omap3 boards Vimal Singh 2010-04-14 4:37 ` Vimal Singh 2010-04-14 4:38 ` Ghorai, Sukumar 2010-05-04 6:00 ` Ghorai, Sukumar 2010-05-04 6:01 ` Ghorai, Sukumar 2010-05-28 13:48 ` Ghorai, Sukumar 2010-04-13 17:44 ` Sukumar Ghorai 2010-04-16 11:32 ` [PATCH 0/6] nand prefetch-irq support and ecc layout chanage Sukumar Ghorai 2010-04-16 11:32 ` Sukumar Ghorai 2010-04-16 11:34 ` [PATCH 1/6] omap3: GPMC register definition at common location Sukumar Ghorai 2010-04-16 11:34 ` Sukumar Ghorai 2010-04-16 11:35 ` [PATCH 2/6] omap3: NAND Prefetch in IRQ mode support Sukumar Ghorai 2010-04-16 11:35 ` Sukumar Ghorai 2010-04-16 11:35 ` [PATCH 3/6] OMAP NAND: configurable fifo threshold to gain the throughput Sukumar Ghorai 2010-04-16 11:35 ` Sukumar Ghorai 2010-04-16 12:45 ` Vimal Singh 2010-04-16 12:45 ` Vimal Singh 2010-04-16 11:35 ` [PATCH 4/6] omap-3630 NAND: enable NAND io in prefetch-irq mode Sukumar Ghorai 2010-04-16 11:35 ` Sukumar Ghorai 2010-04-16 11:35 ` [PATCH 5/6] omap: NAND: ecc layout select from board file Sukumar Ghorai 2010-04-16 11:35 ` Sukumar Ghorai 2010-04-16 11:35 ` [PATCH 6/6] omap: NAND: Making ecc layout as compatible with romcode ecc Sukumar Ghorai 2010-04-16 11:35 ` Sukumar Ghorai 2010-05-12 9:48 ` [PATCH 0/3] omap3 nand: cleanup exiting platform related code Sukumar Ghorai 2010-05-12 9:48 ` Sukumar Ghorai 2010-05-12 9:48 ` [PATCH 1/3] omap3: GPMC register definition at common location Sukumar Ghorai 2010-05-12 9:48 ` Sukumar Ghorai 2010-05-12 9:48 ` [PATCH 2/3] omap3 nand: cleanup for not to use GPMC virtual address Sukumar Ghorai 2010-05-12 9:48 ` Sukumar Ghorai 2010-05-12 9:48 ` [PATCH 3/3] omap3 nand: fix issue in board file to detect the nand Sukumar Ghorai 2010-05-12 9:48 ` Sukumar Ghorai 2010-05-13 15:41 ` [PATCH 2/3] omap3 nand: cleanup for not to use GPMC virtual address Tony Lindgren 2010-05-13 15:41 ` Tony Lindgren 2010-05-13 18:48 ` Ghorai, Sukumar 2010-05-13 18:48 ` Ghorai, Sukumar 2010-05-13 6:15 ` [PATCH 1/3] omap3: GPMC register definition at common location Mike Rapoport 2010-05-13 6:15 ` Mike Rapoport 2010-05-13 15:41 ` Tony Lindgren 2010-05-13 15:41 ` Tony Lindgren 2010-05-13 15:44 ` [PATCH 0/3] omap3 nand: cleanup exiting platform related code Tony Lindgren 2010-05-13 15:44 ` Tony Lindgren 2010-05-14 15:23 ` [PATCH v2 0/2] " Sukumar Ghorai 2010-05-14 15:23 ` Sukumar Ghorai 2010-05-14 15:23 ` [PATCH v2 1/2] omap3 nand: cleanup for not to use GPMC virtual address Sukumar Ghorai 2010-05-14 15:23 ` Sukumar Ghorai 2010-05-14 15:23 ` [PATCH v2 2/2] omap3 nand: fix issue in board file to detect the nand Sukumar Ghorai 2010-05-14 15:23 ` Sukumar Ghorai 2010-05-14 15:28 ` [PATCH v2 1/2] omap3 nand: cleanup for not to use GPMC virtual address Tony Lindgren 2010-05-14 15:28 ` Tony Lindgren 2010-05-14 18:02 ` Vimal Singh 2010-05-14 18:02 ` Vimal Singh 2010-05-17 4:22 ` Ghorai, Sukumar 2010-05-17 4:22 ` Ghorai, Sukumar 2010-05-17 14:26 ` Vimal Singh 2010-05-17 14:26 ` Vimal Singh 2010-05-17 14:34 ` Ghorai, Sukumar 2010-05-17 14:34 ` Ghorai, Sukumar 2010-05-14 23:58 ` Tony Lindgren 2010-05-14 23:58 ` Tony Lindgren 2010-05-17 5:48 ` Ghorai, Sukumar 2010-05-17 5:48 ` Ghorai, Sukumar 2010-05-18 11:16 ` [PATCH v3 0/3] omap3 nand: cleanup exiting platform related code Sukumar Ghorai 2010-05-18 11:16 ` Sukumar Ghorai 2010-05-18 11:16 ` [PATCH v3 1/3] omap3 gpmc: functionality enhancement Sukumar Ghorai 2010-05-18 11:16 ` Sukumar Ghorai 2010-05-18 11:16 ` [PATCH v3 2/3] omap3 nand: cleanup virtual address usages Sukumar Ghorai 2010-05-18 11:16 ` Sukumar Ghorai 2010-05-18 11:16 ` [PATCH v3 3/3] omap3 nand: fix issue in board file to detect nand Sukumar Ghorai 2010-05-18 11:16 ` Sukumar Ghorai 2010-05-19 15:30 ` [PATCH v3 2/3] omap3 nand: cleanup virtual address usages Vimal Singh 2010-05-19 15:30 ` Vimal Singh 2010-05-19 17:24 ` Ghorai, Sukumar 2010-05-19 17:24 ` Ghorai, Sukumar 2010-05-19 18:07 ` Vimal Singh 2010-05-19 18:07 ` Vimal Singh 2010-05-19 18:19 ` Tony Lindgren 2010-05-19 18:19 ` Tony Lindgren 2010-05-19 14:46 ` Vimal Singh [this message] 2010-05-19 14:46 ` [PATCH v3 1/3] omap3 gpmc: functionality enhancement Vimal Singh 2010-05-19 15:14 ` Peter Barada 2010-05-19 15:14 ` Peter Barada 2010-05-19 15:48 ` Peter Barada 2010-05-19 15:48 ` Peter Barada 2010-05-19 18:04 ` Ghorai, Sukumar 2010-05-19 18:04 ` Ghorai, Sukumar 2010-05-19 18:30 ` Vimal Singh 2010-05-19 18:30 ` Vimal Singh 2010-05-20 5:38 ` Ghorai, Sukumar 2010-05-20 5:38 ` Ghorai, Sukumar 2010-05-20 14:34 ` Vimal Singh 2010-05-20 14:34 ` Vimal Singh 2010-05-25 14:37 ` Ghorai, Sukumar 2010-05-25 14:37 ` Ghorai, Sukumar 2010-05-25 15:34 ` Vimal Singh 2010-05-25 15:34 ` Vimal Singh 2010-05-27 13:24 ` [PATCH v4 0/3] omap3 nand: cleanup exiting platform related code Sukumar Ghorai 2010-05-27 13:24 ` [PATCH v4 1/3] omap3 gpmc: functionality enhancement Sukumar Ghorai 2010-05-27 13:24 ` [PATCH v4 2/3] omap3 nand: cleanup virtual address usages Sukumar Ghorai 2010-05-27 13:24 ` [PATCH v4 3/3] omap3 nand: fix issue in board file to detect nand Sukumar Ghorai 2010-05-27 18:26 ` [PATCH v4 1/3] omap3 gpmc: functionality enhancement Vimal Singh 2010-06-04 7:40 ` [PATCH v5 0/3] omap3 nand: cleanup exiting platform related code Sukumar Ghorai 2010-06-04 7:40 ` Sukumar Ghorai 2010-06-04 7:40 ` [PATCH v5 1/3] omap3 gpmc: functionality enhancement Sukumar Ghorai 2010-06-04 7:40 ` Sukumar Ghorai 2010-06-04 7:40 ` [PATCH v5 2/3] omap3 nand: cleanup virtual address usages Sukumar Ghorai 2010-06-04 7:40 ` Sukumar Ghorai 2010-06-04 7:40 ` [PATCH v5 3/3] omap3 nand: fix issue in board file to detect nand Sukumar Ghorai 2010-06-04 7:40 ` Sukumar Ghorai 2010-07-07 10:21 ` [PATCH v5 2/3] omap3 nand: cleanup virtual address usages Tony Lindgren 2010-07-07 10:21 ` Tony Lindgren 2010-07-07 12:22 ` Ghorai, Sukumar 2010-07-07 12:22 ` Ghorai, Sukumar 2010-07-07 10:18 ` [PATCH v5 1/3] omap3 gpmc: functionality enhancement Tony Lindgren 2010-07-07 10:18 ` Tony Lindgren 2010-07-07 12:32 ` Ghorai, Sukumar 2010-07-07 12:32 ` Ghorai, Sukumar 2010-07-07 13:01 ` Tony Lindgren 2010-07-07 13:01 ` Tony Lindgren 2010-07-08 3:54 ` Ghorai, Sukumar 2010-07-08 3:54 ` Ghorai, Sukumar 2010-06-08 17:12 ` [PATCH v5 0/3] omap3 nand: cleanup exiting platform related code Vimal Singh 2010-06-08 17:12 ` Vimal Singh 2010-06-15 13:26 ` Ghorai, Sukumar 2010-06-15 13:26 ` Ghorai, Sukumar 2010-06-30 14:42 ` Ghorai, Sukumar 2010-06-30 14:42 ` Ghorai, Sukumar 2010-06-16 11:39 ` [PATCH v3 0/8] nand support on omap3 boards Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 1/8] omap3 flash: rename board-sdp-flash.c to be use by other boards Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 2/8] omap3: add support for NAND on zoom2 board Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 3/8] omap3: add support for NAND on zoom3 board Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 4/8] omap-3630-sdp : Add support for Flash Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 5/8] omap3: add support for NAND on LDP board Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 6/8] omap-3630-sdp: enable Flash device support Sukumar Ghorai 2010-06-16 11:39 ` [PATCH v3 7/8] zoom2: enable NAND support Sukumar Ghorai 2010-06-16 11:40 ` [PATCH v3 8/8] zoom3: " Sukumar Ghorai 2010-07-05 12:27 ` [PATCH v3 6/8] omap-3630-sdp: enable Flash device support Tony Lindgren 2010-07-06 5:23 ` Ghorai, Sukumar 2010-07-05 12:23 ` [PATCH v3 1/8] omap3 flash: rename board-sdp-flash.c to be use by other boards Tony Lindgren 2010-07-06 6:05 ` Shilimkar, Santosh 2010-07-06 6:27 ` Ghorai, Sukumar
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=AANLkTikFxtzDpiJvJjnuonM2urMJR1LDLafx5JtpC_bS@mail.gmail.com \ --to=vimal.newwork@gmail.com \ --cc=Artem.Bityutskiy@nokia.com \ --cc=linux-mtd@lists.infradead.org \ --cc=linux-omap@vger.kernel.org \ --cc=mike@compulab.co.il \ --cc=s-ghorai@ti.com \ --cc=sakoman@gmail.com \ --cc=tony@atomide.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.