From: Dillon Min <dillon.minfei@gmail.com>
To: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>,
Stefan Riedmueller <s.riedmueller@phytec.de>,
Matthias Schiffer <matthias.schiffer@ew.tq-group.com>,
leoyang.li@nxp.com, Arnd Bergmann <arnd@arndb.de>,
Olof Johansson <olof@lixom.net>,
Sascha Hauer <s.hauer@pengutronix.de>,
Sascha Hauer <kernel@pengutronix.de>,
"Lad, Prabhakar" <prabhakar.csengg@gmail.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
mchehab+huawei@kernel.org,
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>,
Krzysztof Kozlowski <krzk@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Oleksij Rempel <linux@rempel-privat.de>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>,
NXP Linux Team <linux-imx@nxp.com>,
linux-media <linux-media@vger.kernel.org>
Subject: Re: [PATCH v5 3/4] arm: dts: imx: Add i.mx6q DaSheng COM-9XX SBC board support
Date: Sun, 23 May 2021 10:34:48 +0800 [thread overview]
Message-ID: <CAL9mu0JDowhMqOQuWor6y7dMqbWhY1i9fgjn-xWNkwXLf3Mhig@mail.gmail.com> (raw)
In-Reply-To: <20210523022534.GJ8194@dragon>
Hi Shawn,
Thanks for the reply.
On Sun, May 23, 2021 at 10:25 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Tue, May 04, 2021 at 01:09:52PM +0800, dillon.minfei@gmail.com wrote:
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > The DaSheng Com-9xx is and ARM based signle board computer (SBC)
> > featuring:
> > - i.MX6Q
> > - 2GiB LPDDR3 DRAM
> > - 8GiB eMMC 5.0 FLASH
> > - 4MiB SPI Flash
> > - USB 2.0 Host/Device
> > - Multiple multi-protocol RS232/RS485 Serial ports
> > - microSD socket
> > - 5V DC power input
> > - HDMI1.4a,1080p@60
> > - RGMIIx1 Gigabit Ethernet
> > - CSI0x1, connect with ov2659
> >
> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
>
> Idiomatically we use 'ARM: dts: ...' for arch/arm DTS patch prefix.
Okay, i will follow this rule in my next submission. thanks.
>
> > ---
> >
> > v5:
> > - no code change, just change my git author name from lower case to higher case
> >
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6q-ds.dts | 17 ++
> > arch/arm/boot/dts/imx6qdl-ds.dtsi | 460 ++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 478 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6q-ds.dts
> > create mode 100644 arch/arm/boot/dts/imx6qdl-ds.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index a19c5ab9df84..425fe17ef7c1 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -510,6 +510,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6q-display5-tianma-tm070-1280x768.dtb \
> > imx6q-dmo-edmqmx6.dtb \
> > imx6q-dms-ba16.dtb \
> > + imx6q-ds.dtb \
> > imx6q-emcon-avari.dtb \
> > imx6q-evi.dtb \
> > imx6q-gk802.dtb \
> > diff --git a/arch/arm/boot/dts/imx6q-ds.dts b/arch/arm/boot/dts/imx6q-ds.dts
> > new file mode 100644
> > index 000000000000..b0a63a133977
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-ds.dts
> > @@ -0,0 +1,17 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +//
> > +// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
> > +//
> > +// Based on imx6qdl-sabresd.dtsi which is:
> > +// Copyright 2012 Freescale Semiconductor, Inc.
> > +// Copyright 2011 Linaro Ltd.
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q.dtsi"
> > +#include "imx6qdl-ds.dtsi"
> > +
> > +/ {
> > + model = "DaSheng i.MX6 Quad Com-9xx Board";
> > + compatible = "ds,imx6q-sbc", "fsl,imx6q";
> > +};
> > diff --git a/arch/arm/boot/dts/imx6qdl-ds.dtsi b/arch/arm/boot/dts/imx6qdl-ds.dtsi
> > new file mode 100644
> > index 000000000000..a2069caf4ea7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-ds.dtsi
> > @@ -0,0 +1,460 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +//
> > +// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
> > +//
> > +// Based on imx6qdl-sabresd.dtsi which is:
> > +// Copyright 2012 Freescale Semiconductor, Inc.
> > +// Copyright 2011 Linaro Ltd.
> > +
> > +#include <dt-bindings/clock/imx6qdl-clock.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > + chosen {
> > + stdout-path = &uart4;
> > + };
> > +
> > + memory@10000000 {
> > + device_type = "memory";
> > + reg = <0x10000000 0x80000000>;
> > + };
> > +
> > + reg_usb_otg_vbus: regulator-usb-otg-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_h1_vbus: regulator-usb-h1-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_h1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
>
> always-on is meaningless for fixed regulators that do not have on/off
> control.
Thanks for point it.
>
> I fixed them up and applied the patch.
Thanks.
>
> Shawn
>
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpio_leds>;
> > +
> > + led-0 {
> > + gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +};
> > +
> > +&ipu1_csi0_from_ipu1_csi0_mux {
> > + bus-width = <8>;
> > + data-shift = <12>; /* Lines 19:12 used */
> > + hsync-active = <1>;
> > + vsync-active = <1>;
> > +};
> > +
> > +&ipu1_csi0_mux_from_parallel_sensor {
> > + remote-endpoint = <&ov2659_to_ipu1_csi0_mux>;
> > +};
> > +
> > +&ipu1_csi0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi1 {
> > + cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_gpio>;
> > + status = "okay";
> > +
> > + m25p80: flash@0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "st,m25p80", "jedec,spi-nor";
> > + spi-max-frequency = <20000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <&phy>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + phy: ethernet-phy@1 {
> > + reg = <1>;
> > + qca,clk-out-frequency = <125000000>;
> > + reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + };
> > + };
> > +};
> > +
> > +&hdmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hdmi_cec>;
> > + ddc-i2c-bus = <&i2c3>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + pfuze100: pmic@8 {
> > + compatible = "fsl,pfuze100";
> > + reg = <0x08>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw3a_reg: sw3a {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3b_reg: sw3b {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + ov2659: camera@30 {
> > + compatible = "ovti,ov2659";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ov2659>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + clock-names = "xvclk";
> > + reg = <0x30>;
> > + powerdown-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +
> > + port {
> > + ov2659_to_ipu1_csi0_mux: endpoint {
> > + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> > + link-frequencies = /bits/ 64 <70000000>;
> > + bus-width = <8>;
> > + hsync-active = <1>;
> > + vsync-active = <1>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> > + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi1_gpio: ecspi1grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
> > + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
> > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
> > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_hdmi_cec: hdmicecgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_ipu1_csi0: ipu1csi0grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> > + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
> > + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_ov2659: ov2659grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x1b0b0
> > + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
> > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usbotg: usbotggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
> > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
> > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
> > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
> > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
> > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_gpio: usdhc1grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
> > + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_wdog: wdoggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_gpio_leds: gpioledsgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0
> > + >;
> > + };
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usb_h1_vbus>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> > + wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> > + status = "disabled";
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + bus-width = <8>;
> > + non-removable;
> > + no-1-8-v;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + status = "disabled";
> > +};
> > +
> > +&wdog2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wdog>;
> > + fsl,ext-reset-output;
> > + status = "okay";
> > +};
> > --
> > 1.9.1
> >
WARNING: multiple messages have this Message-ID (diff)
From: Dillon Min <dillon.minfei@gmail.com>
To: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>,
Stefan Riedmueller <s.riedmueller@phytec.de>,
Matthias Schiffer <matthias.schiffer@ew.tq-group.com>,
leoyang.li@nxp.com, Arnd Bergmann <arnd@arndb.de>,
Olof Johansson <olof@lixom.net>,
Sascha Hauer <s.hauer@pengutronix.de>,
Sascha Hauer <kernel@pengutronix.de>,
"Lad, Prabhakar" <prabhakar.csengg@gmail.com>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
mchehab+huawei@kernel.org,
Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>,
Krzysztof Kozlowski <krzk@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Oleksij Rempel <linux@rempel-privat.de>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Linux ARM <linux-arm-kernel@lists.infradead.org>,
NXP Linux Team <linux-imx@nxp.com>,
linux-media <linux-media@vger.kernel.org>
Subject: Re: [PATCH v5 3/4] arm: dts: imx: Add i.mx6q DaSheng COM-9XX SBC board support
Date: Sun, 23 May 2021 10:34:48 +0800 [thread overview]
Message-ID: <CAL9mu0JDowhMqOQuWor6y7dMqbWhY1i9fgjn-xWNkwXLf3Mhig@mail.gmail.com> (raw)
In-Reply-To: <20210523022534.GJ8194@dragon>
Hi Shawn,
Thanks for the reply.
On Sun, May 23, 2021 at 10:25 AM Shawn Guo <shawnguo@kernel.org> wrote:
>
> On Tue, May 04, 2021 at 01:09:52PM +0800, dillon.minfei@gmail.com wrote:
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > The DaSheng Com-9xx is and ARM based signle board computer (SBC)
> > featuring:
> > - i.MX6Q
> > - 2GiB LPDDR3 DRAM
> > - 8GiB eMMC 5.0 FLASH
> > - 4MiB SPI Flash
> > - USB 2.0 Host/Device
> > - Multiple multi-protocol RS232/RS485 Serial ports
> > - microSD socket
> > - 5V DC power input
> > - HDMI1.4a,1080p@60
> > - RGMIIx1 Gigabit Ethernet
> > - CSI0x1, connect with ov2659
> >
> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
>
> Idiomatically we use 'ARM: dts: ...' for arch/arm DTS patch prefix.
Okay, i will follow this rule in my next submission. thanks.
>
> > ---
> >
> > v5:
> > - no code change, just change my git author name from lower case to higher case
> >
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/imx6q-ds.dts | 17 ++
> > arch/arm/boot/dts/imx6qdl-ds.dtsi | 460 ++++++++++++++++++++++++++++++++++++++
> > 3 files changed, 478 insertions(+)
> > create mode 100644 arch/arm/boot/dts/imx6q-ds.dts
> > create mode 100644 arch/arm/boot/dts/imx6qdl-ds.dtsi
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index a19c5ab9df84..425fe17ef7c1 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -510,6 +510,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> > imx6q-display5-tianma-tm070-1280x768.dtb \
> > imx6q-dmo-edmqmx6.dtb \
> > imx6q-dms-ba16.dtb \
> > + imx6q-ds.dtb \
> > imx6q-emcon-avari.dtb \
> > imx6q-evi.dtb \
> > imx6q-gk802.dtb \
> > diff --git a/arch/arm/boot/dts/imx6q-ds.dts b/arch/arm/boot/dts/imx6q-ds.dts
> > new file mode 100644
> > index 000000000000..b0a63a133977
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6q-ds.dts
> > @@ -0,0 +1,17 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +//
> > +// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
> > +//
> > +// Based on imx6qdl-sabresd.dtsi which is:
> > +// Copyright 2012 Freescale Semiconductor, Inc.
> > +// Copyright 2011 Linaro Ltd.
> > +
> > +/dts-v1/;
> > +
> > +#include "imx6q.dtsi"
> > +#include "imx6qdl-ds.dtsi"
> > +
> > +/ {
> > + model = "DaSheng i.MX6 Quad Com-9xx Board";
> > + compatible = "ds,imx6q-sbc", "fsl,imx6q";
> > +};
> > diff --git a/arch/arm/boot/dts/imx6qdl-ds.dtsi b/arch/arm/boot/dts/imx6qdl-ds.dtsi
> > new file mode 100644
> > index 000000000000..a2069caf4ea7
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx6qdl-ds.dtsi
> > @@ -0,0 +1,460 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +//
> > +// Copyright 2021 Dillon Min <dillon.minfei@gmail.com>
> > +//
> > +// Based on imx6qdl-sabresd.dtsi which is:
> > +// Copyright 2012 Freescale Semiconductor, Inc.
> > +// Copyright 2011 Linaro Ltd.
> > +
> > +#include <dt-bindings/clock/imx6qdl-clock.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > + chosen {
> > + stdout-path = &uart4;
> > + };
> > +
> > + memory@10000000 {
> > + device_type = "memory";
> > + reg = <0x10000000 0x80000000>;
> > + };
> > +
> > + reg_usb_otg_vbus: regulator-usb-otg-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_otg_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_h1_vbus: regulator-usb-h1-vbus {
> > + compatible = "regulator-fixed";
> > + regulator-name = "usb_h1_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
>
> always-on is meaningless for fixed regulators that do not have on/off
> control.
Thanks for point it.
>
> I fixed them up and applied the patch.
Thanks.
>
> Shawn
>
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_gpio_leds>;
> > +
> > + led-0 {
> > + gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
> > + default-state = "on";
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +};
> > +
> > +&ipu1_csi0_from_ipu1_csi0_mux {
> > + bus-width = <8>;
> > + data-shift = <12>; /* Lines 19:12 used */
> > + hsync-active = <1>;
> > + vsync-active = <1>;
> > +};
> > +
> > +&ipu1_csi0_mux_from_parallel_sensor {
> > + remote-endpoint = <&ov2659_to_ipu1_csi0_mux>;
> > +};
> > +
> > +&ipu1_csi0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ipu1_csi0>;
> > + status = "okay";
> > +};
> > +
> > +&ecspi1 {
> > + cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_gpio>;
> > + status = "okay";
> > +
> > + m25p80: flash@0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "st,m25p80", "jedec,spi-nor";
> > + spi-max-frequency = <20000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +&fec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_enet>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <&phy>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + phy: ethernet-phy@1 {
> > + reg = <1>;
> > + qca,clk-out-frequency = <125000000>;
> > + reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
> > + reset-assert-us = <10000>;
> > + };
> > + };
> > +};
> > +
> > +&hdmi {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_hdmi_cec>;
> > + ddc-i2c-bus = <&i2c3>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + pfuze100: pmic@8 {
> > + compatible = "fsl,pfuze100";
> > + reg = <0x08>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <6250>;
> > + };
> > +
> > + sw3a_reg: sw3a {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw3b_reg: sw3b {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + ov2659: camera@30 {
> > + compatible = "ovti,ov2659";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ov2659>;
> > + clocks = <&clks IMX6QDL_CLK_CKO>;
> > + clock-names = "xvclk";
> > + reg = <0x30>;
> > + powerdown-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +
> > + port {
> > + ov2659_to_ipu1_csi0_mux: endpoint {
> > + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
> > + link-frequencies = /bits/ 64 <70000000>;
> > + bus-width = <8>;
> > + hsync-active = <1>;
> > + vsync-active = <1>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&iomuxc {
> > + pinctrl_ecspi1: ecspi1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> > + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> > + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> > + >;
> > + };
> > +
> > + pinctrl_ecspi1_gpio: ecspi1grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
> > + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_enet: enetgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> > + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> > + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
> > + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
> > + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
> > + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
> > + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
> > + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
> > + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> > + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> > + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> > + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> > + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> > + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> > + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> > + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_hdmi_cec: hdmicecgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
> > + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> > + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> > + >;
> > + };
> > +
> > + pinctrl_ipu1_csi0: ipu1csi0grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> > + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> > + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> > + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
> > + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_ov2659: ov2659grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x1b0b0
> > + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
> > + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
> > + >;
> > + };
> > +
> > + pinctrl_uart4: uart4grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> > + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> > + >;
> > + };
> > +
> > + pinctrl_usbotg: usbotggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
> > + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
> > + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
> > + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
> > + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
> > + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_gpio: usdhc1grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> > + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> > + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> > + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> > + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> > + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
> > + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> > + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> > + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> > + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> > + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> > + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> > + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> > + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> > + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> > + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> > + >;
> > + };
> > +
> > + pinctrl_wdog: wdoggrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
> > + >;
> > + };
> > +
> > + pinctrl_gpio_leds: gpioledsgrp {
> > + fsl,pins = <
> > + MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0
> > + >;
> > + };
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart4>;
> > + status = "okay";
> > +};
> > +
> > +&usbh1 {
> > + vbus-supply = <®_usb_h1_vbus>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + vbus-supply = <®_usb_otg_vbus>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usbotg>;
> > + disable-over-current;
> > + status = "okay";
> > +};
> > +
> > +&usdhc1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> > + bus-width = <4>;
> > + cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> > + wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> > + status = "disabled";
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + bus-width = <8>;
> > + non-removable;
> > + no-1-8-v;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + status = "disabled";
> > +};
> > +
> > +&wdog2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wdog>;
> > + fsl,ext-reset-output;
> > + status = "okay";
> > +};
> > --
> > 1.9.1
> >
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-05-23 2:35 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-04 5:09 [PATCH v5 0/4] arm: imx: Add i.mx6q DaSheng COM-9XX SBC board support dillon.minfei
2021-05-04 5:09 ` dillon.minfei
2021-05-04 5:09 ` [PATCH v5 1/4] dt-bindings: add dasheng vendor prefix dillon.minfei
2021-05-04 5:09 ` dillon.minfei
2021-05-23 2:20 ` Shawn Guo
2021-05-23 2:20 ` Shawn Guo
2021-05-04 5:09 ` [PATCH v5 2/4] dt-bindings: arm: imx: Add i.mx6q DaSheng COM-9XX SBC dillon.minfei
2021-05-04 5:09 ` dillon.minfei
2021-05-23 2:21 ` Shawn Guo
2021-05-23 2:21 ` Shawn Guo
2021-05-04 5:09 ` [PATCH v5 3/4] arm: dts: imx: Add i.mx6q DaSheng COM-9XX SBC board support dillon.minfei
2021-05-04 5:09 ` dillon.minfei
2021-05-11 15:18 ` Dillon Min
2021-05-11 15:18 ` Dillon Min
2021-05-23 2:25 ` Shawn Guo
2021-05-23 2:25 ` Shawn Guo
2021-05-23 2:34 ` Dillon Min [this message]
2021-05-23 2:34 ` Dillon Min
2021-05-04 5:09 ` [PATCH v5 4/4] media: i2c: ov2659: Use clk_{prepare_enable,disable_unprepare}() to set xvclk on/off dillon.minfei
2021-05-04 5:09 ` [PATCH v5 4/4] media: i2c: ov2659: Use clk_{prepare_enable, disable_unprepare}() " dillon.minfei
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAL9mu0JDowhMqOQuWor6y7dMqbWhY1i9fgjn-xWNkwXLf3Mhig@mail.gmail.com \
--to=dillon.minfei@gmail.com \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=krzk@kernel.org \
--cc=krzysztof.kozlowski@canonical.com \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux@rempel-privat.de \
--cc=matthias.schiffer@ew.tq-group.com \
--cc=mchehab+huawei@kernel.org \
--cc=mchehab@kernel.org \
--cc=olof@lixom.net \
--cc=prabhakar.csengg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=s.riedmueller@phytec.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.