From: Jagan Teki <jagan@amarulasolutions.com>
To: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>, Icenowy Zheng <icenowy@aosc.io>,
Jernej Skrabec <jernej.skrabec@siol.net>,
Vasily Khoruzhick <anarsoul@gmail.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>,
David Airlie <airlied@linux.ie>,
dri-devel <dri-devel@lists.freedesktop.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
linux-clk <linux-clk@vger.kernel.org>,
Michael Trimarchi <michael@amarulasolutions.com>,
linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
devicetree <devicetree@vger.kernel.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
linux-sunxi@googlegroups.com
Subject: Re: [PATCH v3 12/25] drm/sun4i: sun6i_mipi_dsi: Add DSI hblk packet overhead
Date: Mon, 29 Oct 2018 19:56:27 +0530 [thread overview]
Message-ID: <CAMty3ZBHU5eXRLLJmUroLgSKcF6O9gHOHRM1XBnt9_Lp7B8rEA@mail.gmail.com> (raw)
In-Reply-To: <20181029092227.mdxgvg5aqzh22j72@flea>
On Mon, Oct 29, 2018 at 2:52 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> On Fri, Oct 26, 2018 at 08:13:31PM +0530, Jagan Teki wrote:
> > Add 10 bytes packet overhead for hblk where blank is set using
> > a blanking packet like (4 bytes + 4 bytes + payload + 2 bytes)
> >
> > This is according to BSP code from BPI-M64-bsp
> > (in drivers/video/sunxi/disp2/disp/de/lowlevel_sun50iw1/de_dsi.c)
> > dsi_hblk = (ht-hspw)*dsi_pixel_bits[format]/8-(4+4+2);
> >
> > So, add 10 bytes packet overhead for DSI hblk.
> >
> > Tested on 2-lane, 4-lane MIPI-DSI LCD panels.
> >
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > Tested-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> > Changes for v3:
> > - new patch
> > Changes for v2:
> > - none
> >
> > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 9 +++++++--
> > 1 file changed, 7 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > index 596e560263bf..cf42be1f1ba1 100644
> > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > @@ -461,7 +461,7 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> > {
> > struct mipi_dsi_device *device = dsi->device;
> > unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
> > - u16 hbp, hfp, hsa, hblk, vblk;
> > + u16 hbp, hfp, hsa, hblk_max, hblk, vblk;
> > size_t bytes;
> > u8 *buffer;
> >
> > @@ -494,8 +494,13 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> >
> > /*
> > * hblk seems to be the line + porches length.
> > + * The blank is set using a blanking packet (4 bytes + 4 bytes +
> > + * payload + 2 bytes). So minimal size is 10 bytes
> > */
> > - hblk = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > +#define HBLK_PACKET_OVERHEAD 10
> > + hblk_max = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > + hblk_max -= HBLK_PACKET_OVERHEAD;
> > + hblk = max((unsigned int)HBLK_PACKET_OVERHEAD, hblk_max);
>
> I'd rather use the same convention than the other assignments done
> before in that function.
Yes, old code did use hsa. but it's added 10 bytes packet head instead
of subtracting it.
hblk = mode->htotal * Bpp - hsa;
=> mode->htotal * Bpp - (mode->hsync_end - mode->hsync_start) * Bpp -
HSA_PACKET_OVERHEAD);
=> (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp +
HSA_PACKET_OVERHEAD;
And it should be
(mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp -
HSA_PACKET_OVERHEAD;
This patch is simply doing the same by explicitly adding packet over
ahead macro, which again used in hfp.
WARNING: multiple messages have this Message-ID (diff)
From: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
To: Maxime Ripard <maxime.ripard-LDxbnhwyfcJBDgjK7y7TUQ@public.gmane.org>
Cc: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>,
Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>,
Jernej Skrabec <jernej.skrabec-gGgVlfcn5nU@public.gmane.org>,
Vasily Khoruzhick
<anarsoul-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>,
Catalin Marinas <catalin.marinas-5wv7dgnIgG8@public.gmane.org>,
Will Deacon <will.deacon-5wv7dgnIgG8@public.gmane.org>,
David Airlie <airlied-cv59FeDIM0c@public.gmane.org>,
dri-devel
<dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW@public.gmane.org>,
Michael Turquette
<mturquette-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>,
Stephen Boyd <sboyd-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
linux-clk <linux-clk-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
Michael Trimarchi
<michael-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>,
linux-arm-kernel
<linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org>,
devicetree <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
linux-kernel
<linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org
Subject: Re: [PATCH v3 12/25] drm/sun4i: sun6i_mipi_dsi: Add DSI hblk packet overhead
Date: Mon, 29 Oct 2018 19:56:27 +0530 [thread overview]
Message-ID: <CAMty3ZBHU5eXRLLJmUroLgSKcF6O9gHOHRM1XBnt9_Lp7B8rEA@mail.gmail.com> (raw)
In-Reply-To: <20181029092227.mdxgvg5aqzh22j72@flea>
On Mon, Oct 29, 2018 at 2:52 PM Maxime Ripard <maxime.ripard-LDxbnhwyfcJBDgjK7y7TUQ@public.gmane.org> wrote:
>
> On Fri, Oct 26, 2018 at 08:13:31PM +0530, Jagan Teki wrote:
> > Add 10 bytes packet overhead for hblk where blank is set using
> > a blanking packet like (4 bytes + 4 bytes + payload + 2 bytes)
> >
> > This is according to BSP code from BPI-M64-bsp
> > (in drivers/video/sunxi/disp2/disp/de/lowlevel_sun50iw1/de_dsi.c)
> > dsi_hblk = (ht-hspw)*dsi_pixel_bits[format]/8-(4+4+2);
> >
> > So, add 10 bytes packet overhead for DSI hblk.
> >
> > Tested on 2-lane, 4-lane MIPI-DSI LCD panels.
> >
> > Signed-off-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
> > Tested-by: Jagan Teki <jagan-dyjBcgdgk7Pe9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
> > ---
> > Changes for v3:
> > - new patch
> > Changes for v2:
> > - none
> >
> > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 9 +++++++--
> > 1 file changed, 7 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > index 596e560263bf..cf42be1f1ba1 100644
> > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > @@ -461,7 +461,7 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> > {
> > struct mipi_dsi_device *device = dsi->device;
> > unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
> > - u16 hbp, hfp, hsa, hblk, vblk;
> > + u16 hbp, hfp, hsa, hblk_max, hblk, vblk;
> > size_t bytes;
> > u8 *buffer;
> >
> > @@ -494,8 +494,13 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> >
> > /*
> > * hblk seems to be the line + porches length.
> > + * The blank is set using a blanking packet (4 bytes + 4 bytes +
> > + * payload + 2 bytes). So minimal size is 10 bytes
> > */
> > - hblk = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > +#define HBLK_PACKET_OVERHEAD 10
> > + hblk_max = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > + hblk_max -= HBLK_PACKET_OVERHEAD;
> > + hblk = max((unsigned int)HBLK_PACKET_OVERHEAD, hblk_max);
>
> I'd rather use the same convention than the other assignments done
> before in that function.
Yes, old code did use hsa. but it's added 10 bytes packet head instead
of subtracting it.
hblk = mode->htotal * Bpp - hsa;
=> mode->htotal * Bpp - (mode->hsync_end - mode->hsync_start) * Bpp -
HSA_PACKET_OVERHEAD);
=> (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp +
HSA_PACKET_OVERHEAD;
And it should be
(mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp -
HSA_PACKET_OVERHEAD;
This patch is simply doing the same by explicitly adding packet over
ahead macro, which again used in hfp.
WARNING: multiple messages have this Message-ID (diff)
From: jagan@amarulasolutions.com (Jagan Teki)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 12/25] drm/sun4i: sun6i_mipi_dsi: Add DSI hblk packet overhead
Date: Mon, 29 Oct 2018 19:56:27 +0530 [thread overview]
Message-ID: <CAMty3ZBHU5eXRLLJmUroLgSKcF6O9gHOHRM1XBnt9_Lp7B8rEA@mail.gmail.com> (raw)
In-Reply-To: <20181029092227.mdxgvg5aqzh22j72@flea>
On Mon, Oct 29, 2018 at 2:52 PM Maxime Ripard <maxime.ripard@bootlin.com> wrote:
>
> On Fri, Oct 26, 2018 at 08:13:31PM +0530, Jagan Teki wrote:
> > Add 10 bytes packet overhead for hblk where blank is set using
> > a blanking packet like (4 bytes + 4 bytes + payload + 2 bytes)
> >
> > This is according to BSP code from BPI-M64-bsp
> > (in drivers/video/sunxi/disp2/disp/de/lowlevel_sun50iw1/de_dsi.c)
> > dsi_hblk = (ht-hspw)*dsi_pixel_bits[format]/8-(4+4+2);
> >
> > So, add 10 bytes packet overhead for DSI hblk.
> >
> > Tested on 2-lane, 4-lane MIPI-DSI LCD panels.
> >
> > Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> > Tested-by: Jagan Teki <jagan@amarulasolutions.com>
> > ---
> > Changes for v3:
> > - new patch
> > Changes for v2:
> > - none
> >
> > drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c | 9 +++++++--
> > 1 file changed, 7 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > index 596e560263bf..cf42be1f1ba1 100644
> > --- a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > +++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
> > @@ -461,7 +461,7 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> > {
> > struct mipi_dsi_device *device = dsi->device;
> > unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
> > - u16 hbp, hfp, hsa, hblk, vblk;
> > + u16 hbp, hfp, hsa, hblk_max, hblk, vblk;
> > size_t bytes;
> > u8 *buffer;
> >
> > @@ -494,8 +494,13 @@ static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
> >
> > /*
> > * hblk seems to be the line + porches length.
> > + * The blank is set using a blanking packet (4 bytes + 4 bytes +
> > + * payload + 2 bytes). So minimal size is 10 bytes
> > */
> > - hblk = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > +#define HBLK_PACKET_OVERHEAD 10
> > + hblk_max = (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp;
> > + hblk_max -= HBLK_PACKET_OVERHEAD;
> > + hblk = max((unsigned int)HBLK_PACKET_OVERHEAD, hblk_max);
>
> I'd rather use the same convention than the other assignments done
> before in that function.
Yes, old code did use hsa. but it's added 10 bytes packet head instead
of subtracting it.
hblk = mode->htotal * Bpp - hsa;
=> mode->htotal * Bpp - (mode->hsync_end - mode->hsync_start) * Bpp -
HSA_PACKET_OVERHEAD);
=> (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp +
HSA_PACKET_OVERHEAD;
And it should be
(mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp -
HSA_PACKET_OVERHEAD;
This patch is simply doing the same by explicitly adding packet over
ahead macro, which again used in hfp.
next prev parent reply other threads:[~2018-10-29 14:26 UTC|newest]
Thread overview: 171+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-26 14:43 [PATCH v3 00/25] drm/sun4i: Allwinner A64 MIPI-DSI support Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 01/25] clk: sunxi-ng: a64: Fix gate bit of DSI DPHY Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 02/25] clk: sunxi-ng: Add check for minimal rate to NKM PLLs Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 03/25] clk: sunxi-ng: Add check for maximum " Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 04/25] drm/sun4i: sun6i_mipi_dsi: Add Allwinner A64 MIPI DSI support Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 05/25] dt-bindings: sun6i-dsi: Add compatible for A64 MIPI DSI Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 06/25] drm/sun4i: sun6i_mipi_dsi: Add DSI Generic short write 2 param transfer Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:17 ` Maxime Ripard
2018-10-29 9:17 ` Maxime Ripard
2018-10-29 9:17 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 07/25] drm/sun4i: sun6i_mipi_dsi: Fix VBP size calculation Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 08/25] drm/sun4i: sun6i_mipi_dsi: Fix TCON DRQ set bits Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 09/25] drm/sun4i: sun6i_mipi_dsi: Refactor vertical video start delay Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 10/25] drm/sun4i: sun6i_mipi_dsi: Fix DSI hbp timing value Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 11/25] drm/sun4i: sun6i_mipi_dsi: Fix DSI hblk timing calculation Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 12/25] drm/sun4i: sun6i_mipi_dsi: Add DSI hblk packet overhead Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:22 ` Maxime Ripard
2018-10-29 9:22 ` Maxime Ripard
2018-10-29 9:22 ` Maxime Ripard
2018-10-29 14:26 ` Jagan Teki [this message]
2018-10-29 14:26 ` Jagan Teki
2018-10-29 14:26 ` Jagan Teki
2018-11-05 8:31 ` Maxime Ripard
2018-11-05 8:31 ` Maxime Ripard
2018-11-05 8:31 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 13/25] drm/sun4i: sun6i_mipi_dsi: Fix DSI hfp timing value Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 14/25] drm/sun4i: sun6i_mipi_dsi: Increase hfp packet overhead Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:27 ` Maxime Ripard
2018-10-29 9:27 ` Maxime Ripard
2018-10-29 9:27 ` Maxime Ripard
2018-10-29 14:27 ` Jagan Teki
2018-10-29 14:27 ` Jagan Teki
2018-11-05 8:33 ` Maxime Ripard
2018-11-05 8:33 ` Maxime Ripard
2018-11-05 8:33 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 15/25] drm/sun4i: sun6i_mipi_dsi: Set proper vblk timing calculation Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:30 ` Maxime Ripard
2018-10-29 9:30 ` Maxime Ripard
2018-10-29 9:30 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 16/25] drm/sun4i: sun6i_mipi_dsi: Add support for VCC-DSI voltage regulator Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:31 ` Maxime Ripard
2018-10-29 9:31 ` Maxime Ripard
2018-10-29 9:31 ` Maxime Ripard
2018-10-29 14:48 ` Jagan Teki
2018-10-29 14:48 ` Jagan Teki
2018-11-05 8:34 ` Maxime Ripard
2018-11-05 8:34 ` Maxime Ripard
2018-11-05 8:34 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 17/25] dt-bindings: panel: Add Bananapi S070WV20-CT16 ICN6211 MIPI-DSI to RGB bridge Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-30 20:23 ` Rob Herring
2018-10-30 20:23 ` Rob Herring
2018-10-30 20:23 ` Rob Herring
2018-10-31 8:53 ` Andrzej Hajda
2018-10-31 8:53 ` Andrzej Hajda
2018-10-31 8:53 ` Andrzej Hajda
2018-10-31 8:58 ` Chen-Yu Tsai
2018-10-31 8:58 ` Chen-Yu Tsai
2018-10-31 8:58 ` Chen-Yu Tsai
2018-10-31 9:15 ` Andrzej Hajda
2018-10-31 9:15 ` Andrzej Hajda
2018-10-31 9:15 ` Andrzej Hajda
2018-11-06 18:08 ` Jagan Teki
2018-11-06 18:08 ` Jagan Teki
2018-11-06 18:08 ` Jagan Teki
2018-11-07 9:11 ` Andrzej Hajda
2018-11-07 9:11 ` Andrzej Hajda
2018-11-07 9:11 ` Andrzej Hajda
2018-11-10 7:32 ` Jagan Teki
2018-11-10 7:32 ` Jagan Teki
2018-11-10 7:32 ` Jagan Teki
2018-11-13 7:56 ` Andrzej Hajda
2018-11-13 7:56 ` Andrzej Hajda
2018-11-13 7:56 ` Andrzej Hajda
2018-11-18 18:20 ` Jagan Teki
2018-11-18 18:20 ` Jagan Teki
2018-11-18 18:20 ` Jagan Teki
2018-11-19 9:49 ` Andrzej Hajda
2018-11-19 9:49 ` Andrzej Hajda
2018-11-19 9:49 ` Andrzej Hajda
2018-10-31 9:15 ` [linux-sunxi] " Julian Calaby
2018-10-31 9:15 ` Julian Calaby
2018-10-31 9:15 ` Julian Calaby
2018-11-06 18:13 ` [linux-sunxi] " Jagan Teki
2018-11-06 18:13 ` Jagan Teki
2018-11-06 18:13 ` Jagan Teki
2018-11-07 10:20 ` Julian Calaby
2018-11-07 10:20 ` Julian Calaby
2018-11-07 10:20 ` Julian Calaby
2018-10-26 14:43 ` [PATCH v3 18/25] drm/panel: " Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:33 ` Maxime Ripard
2018-10-29 9:33 ` Maxime Ripard
2018-10-29 9:33 ` Maxime Ripard
2018-10-26 14:43 ` [PATCH v3 19/25] dt-bindings: panel: Add Techstar TS8550B MIPI DSI panel Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-30 20:27 ` Rob Herring
2018-10-30 20:27 ` Rob Herring
2018-10-30 20:27 ` Rob Herring
2018-10-26 14:43 ` [PATCH v3 20/25] drm/panel: Add Techstar TS8550B MIPI-DSI LCD panel Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 16:13 ` [linux-sunxi] " Priit Laes
2018-10-26 16:13 ` Priit Laes
2018-10-26 16:13 ` Priit Laes
2018-10-27 9:55 ` [linux-sunxi] " Jagan Teki
2018-10-27 9:55 ` Jagan Teki
2018-10-27 9:55 ` Jagan Teki
2018-10-27 16:27 ` [linux-sunxi] " Priit Laes
2018-10-27 16:27 ` Priit Laes
2018-10-27 16:27 ` Priit Laes
2018-10-26 14:43 ` [PATCH v3 21/25] clk: sunxi-ng: a64: Add min and max rate for PLL_MIPI Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 22/25] dt-bindings: sun6i-dsi: Add compatible for A64 DPHY Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-30 20:28 ` Rob Herring
2018-10-30 20:28 ` Rob Herring
2018-10-30 20:28 ` Rob Herring
2018-10-31 2:24 ` Chen-Yu Tsai
2018-10-31 2:24 ` Chen-Yu Tsai
2018-10-31 2:24 ` Chen-Yu Tsai
2018-10-26 14:43 ` [PATCH v3 23/25] arm64: dts: allwinner: a64: Add DSI pipeline Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 24/25] [DO NOT MERGE] arm64: dts: allwinner: bananapi-m64: Bananapi S070WV20-CT16 DSI panel Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` [PATCH v3 25/25] arm64: dts: allwinner: a64-amarula-relic: Enable Techstar TS8550B MIPI-DSI panel Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-26 14:43 ` Jagan Teki
2018-10-29 9:15 ` [PATCH v3 00/25] drm/sun4i: Allwinner A64 MIPI-DSI support Maxime Ripard
2018-10-29 9:15 ` Maxime Ripard
2018-10-29 9:15 ` Maxime Ripard
2018-10-29 12:34 ` Jagan Teki
2018-10-29 12:34 ` Jagan Teki
2018-10-29 12:34 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAMty3ZBHU5eXRLLJmUroLgSKcF6O9gHOHRM1XBnt9_Lp7B8rEA@mail.gmail.com \
--to=jagan@amarulasolutions.com \
--cc=airlied@linux.ie \
--cc=anarsoul@gmail.com \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=icenowy@aosc.io \
--cc=jernej.skrabec@siol.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=michael@amarulasolutions.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=wens@csie.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.