From: Rahul Sharma <rahul.sharma@samsung.com> To: Arun Kumar K <arun.kk@samsung.com> Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>, "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>, linux-samsung-soc <linux-samsung-soc@vger.kernel.org>, Kukjin Kim <kgene.kim@samsung.com>, Inki Dae <inki.dae@samsung.com>, Tomasz Figa <tomasz.figa@gmail.com>, sunil joshi <joshi@samsung.com> Subject: Re: [PATCH v3 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board Date: Mon, 12 May 2014 16:23:42 +0530 [thread overview] Message-ID: <CAPdUM4PPQbbtDSZ6_qu-Ld9ku4iNz-zanRVODTvMrLknPStZWA@mail.gmail.com> (raw) In-Reply-To: <5370A7D0.5030409@samsung.com> On 12 May 2014 16:22, Arun Kumar K <arun.kk@samsung.com> wrote: > Hi Rahul, > > On 05/12/14 15:54, Rahul Sharma wrote: >> From: Rahul Sharma <Rahul.Sharma@samsung.com> >> >> Enable hdmi for peach-pi board. >> >> Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com> >> --- >> arch/arm/boot/dts/exynos5800-peach-pi.dts | 26 ++++++++++++++++++++++++++ >> 1 file changed, 26 insertions(+) >> >> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> index 742655b..bbb445a 100644 >> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts >> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> @@ -72,6 +72,13 @@ >> samsung,pin-pud = <0>; >> samsung,pin-drv = <0>; >> }; >> + >> + hdmi_hpd_irq: hdmi-hpd-irq { >> + samsung,pins = "gpx3-7"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <0>; >> + }; > > This node is already added in 5420-pinctrl.dtsi in patch 3/5. > You can drop it from here. > yea correct. I will remove this pin. Regards, Rahul Sharma. > Regards > Arun > >> }; >> >> &rtc { >> @@ -134,6 +141,25 @@ >> }; >> }; >> >> +&i2c_2 { >> + status = "okay"; >> + samsung,i2c-sda-delay = <100>; >> + samsung,i2c-max-bus-freq = <66000>; >> + samsung,i2c-slave-addr = <0x50>; >> + >> + hdmiddc@50 { >> + reg = <0x50>; >> + }; >> +}; >> + >> +&hdmi { >> + status = "okay"; >> + hpd-gpio = <&gpx3 7 2>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&hdmi_hpd_irq>; >> + ddc = <&i2c_2>; >> +}; >> + >> /* >> * Use longest HW watchdog in SoC (32 seconds) since the hardware >> * watchdog provides no debugging information (compared to soft/hard >>
WARNING: multiple messages have this Message-ID (diff)
From: rahul.sharma@samsung.com (Rahul Sharma) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v3 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board Date: Mon, 12 May 2014 16:23:42 +0530 [thread overview] Message-ID: <CAPdUM4PPQbbtDSZ6_qu-Ld9ku4iNz-zanRVODTvMrLknPStZWA@mail.gmail.com> (raw) In-Reply-To: <5370A7D0.5030409@samsung.com> On 12 May 2014 16:22, Arun Kumar K <arun.kk@samsung.com> wrote: > Hi Rahul, > > On 05/12/14 15:54, Rahul Sharma wrote: >> From: Rahul Sharma <Rahul.Sharma@samsung.com> >> >> Enable hdmi for peach-pi board. >> >> Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com> >> --- >> arch/arm/boot/dts/exynos5800-peach-pi.dts | 26 ++++++++++++++++++++++++++ >> 1 file changed, 26 insertions(+) >> >> diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> index 742655b..bbb445a 100644 >> --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts >> +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts >> @@ -72,6 +72,13 @@ >> samsung,pin-pud = <0>; >> samsung,pin-drv = <0>; >> }; >> + >> + hdmi_hpd_irq: hdmi-hpd-irq { >> + samsung,pins = "gpx3-7"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <0>; >> + }; > > This node is already added in 5420-pinctrl.dtsi in patch 3/5. > You can drop it from here. > yea correct. I will remove this pin. Regards, Rahul Sharma. > Regards > Arun > >> }; >> >> &rtc { >> @@ -134,6 +141,25 @@ >> }; >> }; >> >> +&i2c_2 { >> + status = "okay"; >> + samsung,i2c-sda-delay = <100>; >> + samsung,i2c-max-bus-freq = <66000>; >> + samsung,i2c-slave-addr = <0x50>; >> + >> + hdmiddc at 50 { >> + reg = <0x50>; >> + }; >> +}; >> + >> +&hdmi { >> + status = "okay"; >> + hpd-gpio = <&gpx3 7 2>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&hdmi_hpd_irq>; >> + ddc = <&i2c_2>; >> +}; >> + >> /* >> * Use longest HW watchdog in SoC (32 seconds) since the hardware >> * watchdog provides no debugging information (compared to soft/hard >>
next prev parent reply other threads:[~2014-05-12 10:53 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2014-05-12 10:24 [PATCH v3 0/5] ARM: dts: enable hdmi for exynos5 based peach and snow boards Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:24 ` [PATCH v3 1/5] ARM: dts: enable hdmi for exynos5250 based snow board Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:24 ` [PATCH v3 2/5] ARM: dts: change to correct compatible string for exynos5420 hdmi Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:24 ` [PATCH v3 3/5] ARM: dts: enable hdmi for exynos5420 based peach-pit board Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:24 ` [PATCH v3 4/5] ARM: dts: remove chip specific hdmi hpd pin from board Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:24 ` [PATCH v3 5/5] ARM: dts: enable hdmi for exynos5800 based peach-pi board Rahul Sharma 2014-05-12 10:24 ` Rahul Sharma 2014-05-12 10:52 ` Arun Kumar K 2014-05-12 10:52 ` Arun Kumar K 2014-05-12 10:53 ` Rahul Sharma [this message] 2014-05-12 10:53 ` Rahul Sharma 2014-05-12 10:58 ` [PATCH v3 0/5] ARM: dts: enable hdmi for exynos5 based peach and snow boards Rahul Sharma 2014-05-12 10:58 ` Rahul Sharma
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=CAPdUM4PPQbbtDSZ6_qu-Ld9ku4iNz-zanRVODTvMrLknPStZWA@mail.gmail.com \ --to=rahul.sharma@samsung.com \ --cc=arun.kk@samsung.com \ --cc=devicetree@vger.kernel.org \ --cc=inki.dae@samsung.com \ --cc=joshi@samsung.com \ --cc=kgene.kim@samsung.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-samsung-soc@vger.kernel.org \ --cc=tomasz.figa@gmail.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.