* [U-Boot-Users] Probelm with 8266ADS board.
@ 2003-07-11 2:56 =?unknown-8bit?b?77+977+977+9TO+/ve+/ve+/vUXvv73vv73vv73vv73vv73vv70=?=
0 siblings, 0 replies; 2+ messages in thread
From: =?unknown-8bit?b?77+977+977+9TO+/ve+/ve+/vUXvv73vv73vv73vv73vv73vv70=?= @ 2003-07-11 2:56 UTC (permalink / raw)
To: u-boot
Hi All:
I am using MPC8266ADS-PCI board, my board seems crash at
"relocate_code:"
and reboot again and again. So I can see the boot messages repeatly printed
on my
console. Any good ideas ? Thanks a lot.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> MESSAGES DRUING BOOTING, REPEATED
U-Boot 0.4.0 (Jul 10 2003 - 17:37:18)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x0a, busdf 5, cpmdf 1, plldf 0, pllmf 2
- vco_out 396000000, scc_clk 99000000, brg_clk 99000000
- cpu_clk 264000000, cpm_clk 198000000, bus_clk 66000000
CPU: MPC8260 (Rev 14, Mask A.0(A) 2K25A) at 264 MHz
Board: Motorola MPC8266ADS
I2C: ready
DRAM: SDRAM configuration read from SPD
Size per side = 16MB
Organization: 1 sides, 2 banks, 9 Columns, 11 Rows, Data width = 64
bits
Refresh rate = 33, CAS latency = 3
Total size: 16 MB
Top of RAM usable for U-Boot at: 01000000
haha
Reserving 190k for U-Boot at: 00fd0000
Reserving 384k for malloc() at: 00f70000
Reserving 76 Bytes for Board Info at: 00f6ffb4
Reserving 68 Bytes for Global Data at: 00f6ff70
Stack Pointer at: 00f6ff58
New Stack Pointer is: 00f6ff58
before memcpy 16187248, -268419200, 68
after memcpy
U-Boot 0.4.0 (Jul 10 2003 - 17:37:18)
MPC8260 Reset Status: Check Stop, External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core Freq 100-300
- dfbrg 0, corecnf 0x0a, busdf 5, cpmdf 1, plldf 0, pllmf 2
- vco_out 396000000, scc_clk 99000000, brg_clk 99000000
- cpu_clk 264000000, cpm_clk 198000000, bus_clk 66000000
^ permalink raw reply [flat|nested] 2+ messages in thread
* [U-Boot-Users] Probelm with 8266ADS board.
@ 2003-07-11 14:11 Rune Torgersen
0 siblings, 0 replies; 2+ messages in thread
From: Rune Torgersen @ 2003-07-11 14:11 UTC (permalink / raw)
To: u-boot
This is of course a problem with the SDRAM.
Check that CONFIG_PBI is set to 0 (set in top of mpc8266ads.c)
This stets the controller in Bank Based interleave.
I have seen this excact problem when running Page Based access to the
standard 16MB devices.
Page Based is supposed to be faster, and is necessary to use more than 128MB
per chip select.
> -----Original Message-----
> From: *L/E<a [mailto:houcheng@turbonetworks.com.tw]
> Sent: Thursday, July 10, 2003 21:56
> To: U-Boot Users (E-mail)
> Subject: [U-Boot-Users] Probelm with 8266ADS board.
>
>
> Hi All:
> I am using MPC8266ADS-PCI board, my board seems crash at
> "relocate_code:" and reboot again and again. So I can see the
> boot messages repeatly printed on my console. Any good ideas
> ? Thanks a lot.
>
> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> MESSAGES DRUING BOOTING, REPEATED
> U-Boot 0.4.0 (Jul 10 2003 - 17:37:18)
>
> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>
> MPC8260 Clock Configuration
> - Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core
> Freq 100-300
> - dfbrg 0, corecnf 0x0a, busdf 5, cpmdf 1, plldf 0, pllmf 2
> - vco_out 396000000, scc_clk 99000000, brg_clk 99000000
> - cpu_clk 264000000, cpm_clk 198000000, bus_clk 66000000
>
> CPU: MPC8260 (Rev 14, Mask A.0(A) 2K25A) at 264 MHz
> Board: Motorola MPC8266ADS
> I2C: ready
> DRAM: SDRAM configuration read from SPD
> Size per side = 16MB
> Organization: 1 sides, 2 banks, 9 Columns, 11 Rows,
> Data width = 64 bits
> Refresh rate = 33, CAS latency = 3
> Total size: 16 MB
> Top of RAM usable for U-Boot at: 01000000
> haha
> Reserving 190k for U-Boot at: 00fd0000
> Reserving 384k for malloc() at: 00f70000
> Reserving 76 Bytes for Board Info at: 00f6ffb4
> Reserving 68 Bytes for Global Data at: 00f6ff70
> Stack Pointer at: 00f6ff58
> New Stack Pointer is: 00f6ff58
> before memcpy 16187248, -268419200, 68
> after memcpy
>
> U-Boot 0.4.0 (Jul 10 2003 - 17:37:18)
>
> MPC8260 Reset Status: Check Stop, External Soft, External Hard
>
> MPC8260 Clock Configuration
> - Bus-to-Core Mult 4x, VCO Div 2, 60x Bus Freq 25-75 , Core
> Freq 100-300
> - dfbrg 0, corecnf 0x0a, busdf 5, cpmdf 1, plldf 0, pllmf 2
> - vco_out 396000000, scc_clk 99000000, brg_clk 99000000
> - cpu_clk 264000000, cpm_clk 198000000, bus_clk 66000000
>
>
>
>
>
>
> -------------------------------------------------------
> This SF.Net email sponsored by: Parasoft
> Error proof Web apps, automate testing & more.
> Download & eval WebKing and get a free book.
> www.parasoft.com/bulletproofapps1
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2003-07-11 14:11 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2003-07-11 2:56 [U-Boot-Users] Probelm with 8266ADS board =?unknown-8bit?b?77+977+977+9TO+/ve+/ve+/vUXvv73vv73vv73vv73vv73vv70=?=
2003-07-11 14:11 Rune Torgersen
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.