[PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Alim Akhtar]

This patch-set introduces UFS (Universal Flash Storage) host controller support
for Samsung family SoC. Mostly, it consists of UFS PHY and host specific driver.

- Changes since v2:
* fixed build warning by kbuild test robot 
* Added Reported-by tags

- Changes since v1:
* fixed make dt_binding_check error as pointed by Rob
* Addressed Krzysztof's review comments
* Added Reviewed-by tags

 
patch 1/5: define devicetree bindings for UFS PHY
patch 2/5: Adds UFS PHY driver
patch 3/5: define devicetree bindings for UFS HCI 
patch 4/5: Adds Samsung UFS HCI driver
patch 5/5: Enabled UFS on exynos7 platform

Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)


Alim Akhtar (5):
  dt-bindings: phy: Document Samsung UFS PHY bindings
  phy: samsung-ufs: add UFS PHY driver for samsung SoC
  Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
    controller
  scsi: ufs-exynos: add UFS host support for Exynos SoCs
  arm64: dts: Add node for ufs exynos7

 .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
 .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
 .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
 arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
 drivers/phy/samsung/Kconfig                   |    9 +
 drivers/phy/samsung/Makefile                  |    1 +
 drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
 drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
 drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
 drivers/scsi/ufs/Kconfig                      |   12 +
 drivers/scsi/ufs/Makefile                     |    1 +
 drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
 drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
 drivers/scsi/ufs/unipro.h                     |   41 +
 include/linux/phy/phy-samsung-ufs.h           |   70 +
 15 files changed, 2521 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt
 create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
 create mode 100644 drivers/scsi/ufs/ufs-exynos.c
 create mode 100644 drivers/scsi/ufs/ufs-exynos.h
 create mode 100644 include/linux/phy/phy-samsung-ufs.h

-- 
2.17.1

[PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Alim Akhtar]

This patch-set introduces UFS (Universal Flash Storage) host controller support
for Samsung family SoC. Mostly, it consists of UFS PHY and host specific driver.

- Changes since v2:
* fixed build warning by kbuild test robot 
* Added Reported-by tags

- Changes since v1:
* fixed make dt_binding_check error as pointed by Rob
* Addressed Krzysztof's review comments
* Added Reviewed-by tags

 
patch 1/5: define devicetree bindings for UFS PHY
patch 2/5: Adds UFS PHY driver
patch 3/5: define devicetree bindings for UFS HCI 
patch 4/5: Adds Samsung UFS HCI driver
patch 5/5: Enabled UFS on exynos7 platform

Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)


Alim Akhtar (5):
  dt-bindings: phy: Document Samsung UFS PHY bindings
  phy: samsung-ufs: add UFS PHY driver for samsung SoC
  Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
    controller
  scsi: ufs-exynos: add UFS host support for Exynos SoCs
  arm64: dts: Add node for ufs exynos7

 .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
 .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
 .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
 arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
 drivers/phy/samsung/Kconfig                   |    9 +
 drivers/phy/samsung/Makefile                  |    1 +
 drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
 drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
 drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
 drivers/scsi/ufs/Kconfig                      |   12 +
 drivers/scsi/ufs/Makefile                     |    1 +
 drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
 drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
 drivers/scsi/ufs/unipro.h                     |   41 +
 include/linux/phy/phy-samsung-ufs.h           |   70 +
 15 files changed, 2521 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
 create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt
 create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
 create mode 100644 drivers/scsi/ufs/ufs-exynos.c
 create mode 100644 drivers/scsi/ufs/ufs-exynos.h
 create mode 100644 include/linux/phy/phy-samsung-ufs.h

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Alim Akhtar]

This patch documents Samsung UFS PHY device tree bindings

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
 1 file changed, 62 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml

diff --git a/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
new file mode 100644
index 000000000000..df54129004e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,ufs-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung SoC series UFS PHY Device Tree Bindings
+
+maintainers:
+  - Alim Akhtar <alim.akhtar@samsung.com>
+
+properties:
+  "#phy-cells":
+    const: 0
+
+  compatible:
+    enum:
+      - samsung,exynos7-ufs-phy
+
+  reg:
+    maxItems: 1
+    description: PHY base register address
+
+  reg-names:
+    items:
+      - const: phy-pma
+
+  clocks:
+    items:
+      - description: PLL reference clock
+      - description: Referencec clock parrent
+
+  clock-names:
+    items:
+      - const: ref_clk_parent
+      - const: ref_clk
+
+required:
+  - "#phy-cells"
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos7-clk.h>
+
+    ufs_phy: ufs-phy@0x15571800 {
+        compatible = "samsung,exynos7-ufs-phy";
+        reg = <0x15571800 0x240>;
+        reg-names = "phy-pma";
+        samsung,pmu-syscon = <&pmu_system_controller>;
+        #phy-cells = <0>;
+        clocks = <&clock_fsys1 MOUT_FSYS1_PHYCLK_SEL1>,
+                 <&clock_top1 CLK_SCLK_PHY_FSYS1_26M>;
+        clock-names = "ref_clk_parent",
+                      "ref_clk";
+    };
+
+...

base-commit: fb33c6510d5595144d585aa194d377cf74d31911
-- 
2.17.1

[PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Alim Akhtar]

This patch documents Samsung UFS PHY device tree bindings

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
 1 file changed, 62 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml

diff --git a/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
new file mode 100644
index 000000000000..df54129004e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/samsung,ufs-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung SoC series UFS PHY Device Tree Bindings
+
+maintainers:
+  - Alim Akhtar <alim.akhtar@samsung.com>
+
+properties:
+  "#phy-cells":
+    const: 0
+
+  compatible:
+    enum:
+      - samsung,exynos7-ufs-phy
+
+  reg:
+    maxItems: 1
+    description: PHY base register address
+
+  reg-names:
+    items:
+      - const: phy-pma
+
+  clocks:
+    items:
+      - description: PLL reference clock
+      - description: Referencec clock parrent
+
+  clock-names:
+    items:
+      - const: ref_clk_parent
+      - const: ref_clk
+
+required:
+  - "#phy-cells"
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos7-clk.h>
+
+    ufs_phy: ufs-phy@0x15571800 {
+        compatible = "samsung,exynos7-ufs-phy";
+        reg = <0x15571800 0x240>;
+        reg-names = "phy-pma";
+        samsung,pmu-syscon = <&pmu_system_controller>;
+        #phy-cells = <0>;
+        clocks = <&clock_fsys1 MOUT_FSYS1_PHYCLK_SEL1>,
+                 <&clock_top1 CLK_SCLK_PHY_FSYS1_26M>;
+        clock-names = "ref_clk_parent",
+                      "ref_clk";
+    };
+
+...

base-commit: fb33c6510d5595144d585aa194d377cf74d31911
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Alim Akhtar]

This patch introduces Samsung UFS PHY driver. This driver
supports to deal with phy calibration and power control
according to UFS host driver's behavior.

Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
---
 drivers/phy/samsung/Kconfig           |   9 +
 drivers/phy/samsung/Makefile          |   1 +
 drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
 drivers/phy/samsung/phy-samsung-ufs.c | 311 ++++++++++++++++++++++++++
 drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
 include/linux/phy/phy-samsung-ufs.h   |  70 ++++++
 6 files changed, 576 insertions(+)
 create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
 create mode 100644 include/linux/phy/phy-samsung-ufs.h

diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
index 9e483d1fdaf2..fc1e3c17f842 100644
--- a/drivers/phy/samsung/Kconfig
+++ b/drivers/phy/samsung/Kconfig
@@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
 	  Enable PCIe PHY support for Exynos SoC series.
 	  This driver provides PHY interface for Exynos PCIe controller.
 
+config PHY_SAMSUNG_UFS
+	tristate "SAMSUNG SoC series UFS PHY driver"
+	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support the Samsung UFS PHY driver for
+	  Samsung SoCs. This driver provides the interface for UFS
+	  host controller to do PHY related programming.
+
 config PHY_SAMSUNG_USB2
 	tristate "Samsung USB 2.0 PHY driver"
 	depends on HAS_IOMEM
diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
index db9b1aa0de6e..3959100fe8a2 100644
--- a/drivers/phy/samsung/Makefile
+++ b/drivers/phy/samsung/Makefile
@@ -2,6 +2,7 @@
 obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
 obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
 obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
+obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
 phy-exynos-usb2-y			+= phy-samsung-usb2.o
 phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h b/drivers/phy/samsung/phy-exynos7-ufs.h
new file mode 100644
index 000000000000..da981c1ac040
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos7-ufs.h
@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS PHY driver data for Samsung EXYNOS7 SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ */
+#ifndef _PHY_EXYNOS7_UFS_H_
+#define _PHY_EXYNOS7_UFS_H_
+
+#include "phy-samsung-ufs.h"
+
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
+
+/* Calibration for phy initialization */
+static const struct samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
+	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
+	END_UFS_PHY_CFG
+};
+
+static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
+	END_UFS_PHY_CFG
+};
+
+/* Calibration for HS mode series A/B */
+static const struct samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
+	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
+	/* Setting order: 1st(0x16, 2nd(0x15) */
+	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
+	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
+	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
+	END_UFS_PHY_CFG
+};
+
+/* Calibration for HS mode series A/B atfer PMC */
+static const struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
+	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
+	END_UFS_PHY_CFG
+};
+
+static const struct samsung_ufs_phy_cfg *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
+	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
+	[CFG_POST_INIT]		= exynos7_post_init_cfg,
+	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
+	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
+};
+
+static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
+	.cfg = exynos7_ufs_phy_cfgs,
+	.isol = {
+		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
+		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
+		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
+	},
+};
+
+#endif /* _PHY_EXYNOS7_UFS_H_ */
diff --git a/drivers/phy/samsung/phy-samsung-ufs.c b/drivers/phy/samsung/phy-samsung-ufs.c
new file mode 100644
index 000000000000..2d5db24de49b
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-ufs.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UFS PHY driver for Samsung SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-samsung-ufs.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "phy-samsung-ufs.h"
+
+#define for_each_phy_lane(phy, i) \
+	for (i = 0; i < (phy)->lane_cnt; i++)
+#define for_each_phy_cfg(cfg) \
+	for (; (cfg)->id; (cfg)++)
+
+#define PHY_DEF_LANE_CNT	1
+
+static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
+			const struct samsung_ufs_phy_cfg *cfg, u8 lane)
+{
+	enum {LANE_0, LANE_1}; /* lane index */
+
+	switch (lane) {
+	case LANE_0:
+		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
+		break;
+	case LANE_1:
+		if (cfg->id == PHY_TRSV_BLK)
+			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
+		break;
+	}
+}
+
+int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy)
+{
+	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
+	const unsigned int timeout_us = 100000;
+	const unsigned int sleep_us = 10;
+	u32 val;
+	int err;
+
+	err = readl_poll_timeout(
+			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
+			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
+	if (err) {
+		dev_err(ufs_phy->dev,
+			"failed to get phy pll lock acquisition %d\n", err);
+		goto out;
+	}
+
+	err = readl_poll_timeout(
+			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
+			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
+	if (err) {
+		dev_err(ufs_phy->dev,
+			"failed to get phy cdr lock acquisition %d\n", err);
+		goto out;
+	}
+
+out:
+	return err;
+}
+
+int samsung_ufs_phy_calibrate(struct phy *phy)
+{
+	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
+	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
+	const struct samsung_ufs_phy_cfg *cfg;
+	int i;
+	int err = 0;
+
+	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
+		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
+		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
+							ufs_phy->ufs_phy_state);
+		return -EINVAL;
+	}
+
+	if (ufs_phy->is_pre_init)
+		ufs_phy->is_pre_init = false;
+	if (ufs_phy->is_post_init) {
+		ufs_phy->is_post_init = false;
+		ufs_phy->ufs_phy_state = CFG_POST_INIT;
+	}
+	if (ufs_phy->is_pre_pmc) {
+		ufs_phy->is_pre_pmc = false;
+		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
+	}
+	if (ufs_phy->is_post_pmc) {
+		ufs_phy->is_post_pmc = false;
+		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
+	}
+
+	switch (ufs_phy->ufs_phy_state) {
+	case CFG_PRE_INIT:
+		ufs_phy->is_post_init = true;
+		break;
+	case CFG_POST_INIT:
+		ufs_phy->is_pre_pmc = true;
+		break;
+	case CFG_PRE_PWR_HS:
+		ufs_phy->is_post_pmc = true;
+		break;
+	case CFG_POST_PWR_HS:
+		break;
+	default:
+		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
+	}
+
+	cfg = cfgs[ufs_phy->ufs_phy_state];
+	if (!cfg)
+		goto out;
+
+	for_each_phy_cfg(cfg) {
+		for_each_phy_lane(ufs_phy, i) {
+			samsung_ufs_phy_config(ufs_phy, cfg, i);
+		}
+	}
+
+	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
+		err = samsung_ufs_phy_wait_for_lock_acq(phy);
+out:
+	return err;
+}
+
+static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy)
+{
+	struct clk *child, *parent;
+
+	child = devm_clk_get(phy->dev, "ref_clk");
+	if (IS_ERR(child))
+		dev_err(phy->dev, "failed to get ref_clk clock\n");
+	else
+		phy->ref_clk = child;
+
+	parent = devm_clk_get(phy->dev, "ref_clk_parent");
+	if (IS_ERR(parent))
+		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
+	else
+		phy->ref_clk_parent = parent;
+
+	return clk_set_parent(child, parent);
+}
+
+static int samsung_ufs_phy_init(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+
+	_phy->lane_cnt = phy->attrs.bus_width;
+	_phy->ufs_phy_state = CFG_PRE_INIT;
+
+	_phy->is_pre_init = true;
+	_phy->is_post_init = false;
+	_phy->is_pre_pmc = false;
+	_phy->is_post_pmc = false;
+
+	samsung_ufs_phy_clks_init(_phy);
+
+	samsung_ufs_phy_calibrate(phy);
+
+	return 0;
+}
+
+static int samsung_ufs_phy_power_on(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+	int ret;
+
+	ret = clk_prepare_enable(_phy->ref_clk);
+	if (ret) {
+		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
+				__func__, ret);
+		return ret;
+	}
+
+	samsung_ufs_phy_ctrl_isol(_phy, false);
+	return 0;
+}
+
+static int samsung_ufs_phy_power_off(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+
+	samsung_ufs_phy_ctrl_isol(_phy, true);
+	clk_disable_unprepare(_phy->ref_clk);
+	return 0;
+}
+
+static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
+					enum phy_mode mode, int submode)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
+
+	_phy->mode = PHY_MODE_INVALID;
+
+	if (mode > 0)
+		_phy->mode = mode;
+
+	return 0;
+}
+
+static struct phy_ops samsung_ufs_phy_ops = {
+	.init		= samsung_ufs_phy_init,
+	.power_on	= samsung_ufs_phy_power_on,
+	.power_off	= samsung_ufs_phy_power_off,
+	.calibrate	= samsung_ufs_phy_calibrate,
+	.set_mode	= samsung_ufs_phy_set_mode,
+}
+;
+static const struct of_device_id samsung_ufs_phy_match[];
+
+static int samsung_ufs_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	const struct of_device_id *match;
+	struct samsung_ufs_phy *phy;
+	struct phy *gen_phy;
+	struct phy_provider *phy_provider;
+	const struct samsung_ufs_phy_drvdata *drvdata;
+	int err = 0;
+
+	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
+	if (!match) {
+		err = -EINVAL;
+		dev_err(dev, "failed to get match_node\n");
+		goto out;
+	}
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		err = -ENOMEM;
+		goto out;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-pma");
+	phy->reg_pma = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy->reg_pma)) {
+		err = PTR_ERR(phy->reg_pma);
+		goto out;
+	}
+
+	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
+				dev->of_node, "samsung,pmu-syscon");
+	if (IS_ERR(phy->reg_pmu)) {
+		err = PTR_ERR(phy->reg_pmu);
+		dev_err(dev, "failed syscon remap for pmu\n");
+		goto out;
+	}
+
+	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
+	if (IS_ERR(gen_phy)) {
+		err = PTR_ERR(gen_phy);
+		dev_err(dev, "failed to create PHY for ufs-phy\n");
+		goto out;
+	}
+
+	drvdata = match->data;
+	phy->dev = dev;
+	phy->drvdata = drvdata;
+	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
+	phy->isol = &drvdata->isol;
+	phy->lane_cnt = PHY_DEF_LANE_CNT;
+
+	phy_set_drvdata(gen_phy, phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		err = PTR_ERR(phy_provider);
+		dev_err(dev, "failed to register phy-provider\n");
+		goto out;
+	}
+out:
+	return err;
+}
+
+static const struct of_device_id samsung_ufs_phy_match[] = {
+	{
+		.compatible = "samsung,exynos7-ufs-phy",
+		.data = &exynos7_ufs_phy,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
+
+static struct platform_driver samsung_ufs_phy_driver = {
+	.probe  = samsung_ufs_phy_probe,
+	.driver = {
+		.name = "samsung-ufs-phy",
+		.of_match_table = samsung_ufs_phy_match,
+	},
+};
+module_platform_driver(samsung_ufs_phy_driver);
+MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
+MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
+MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/samsung/phy-samsung-ufs.h b/drivers/phy/samsung/phy-samsung-ufs.h
new file mode 100644
index 000000000000..d0ae2b416b2b
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-ufs.h
@@ -0,0 +1,100 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS PHY driver for Samsung EXYNOS SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+#ifndef _PHY_SAMSUNG_UFS_
+#define _PHY_SAMSUNG_UFS_
+
+#define PHY_COMN_BLK	1
+#define PHY_TRSV_BLK	2
+#define END_UFS_PHY_CFG { 0 }
+#define PHY_TRSV_CH_OFFSET	0x30
+#define PHY_APB_ADDR(off)	((off) << 2)
+
+#define PHY_COMN_REG_CFG(o, v, d) {	\
+	.off_0 = PHY_APB_ADDR((o)),	\
+	.off_1 = 0,		\
+	.val = (v),		\
+	.desc = (d),		\
+	.id = PHY_COMN_BLK,	\
+}
+
+#define PHY_TRSV_REG_CFG(o, v, d) {	\
+	.off_0 = PHY_APB_ADDR((o)),	\
+	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
+	.val = (v),		\
+	.desc = (d),		\
+	.id = PHY_TRSV_BLK,	\
+}
+
+/* UFS PHY registers */
+#define PHY_PLL_LOCK_STATUS	0x1e
+#define PHY_CDR_LOCK_STATUS	0x5e
+
+#define PHY_PLL_LOCK_BIT	BIT(5)
+#define PHY_CDR_LOCK_BIT	BIT(4)
+
+/* PHY calibration point/state */
+enum {
+	CFG_PRE_INIT,
+	CFG_POST_INIT,
+	CFG_PRE_PWR_HS,
+	CFG_POST_PWR_HS,
+	CFG_TAG_MAX,
+};
+
+struct samsung_ufs_phy_cfg {
+	u32 off_0;
+	u32 off_1;
+	u32 val;
+	u8 desc;
+	u8 id;
+};
+
+struct samsung_ufs_phy_drvdata {
+	const struct samsung_ufs_phy_cfg **cfg;
+	struct pmu_isol {
+		u32 offset;
+		u32 mask;
+		u32 en;
+	} isol;
+};
+
+struct samsung_ufs_phy {
+	struct device *dev;
+	void __iomem *reg_pma;
+	struct regmap *reg_pmu;
+	struct clk *ref_clk;
+	struct clk *ref_clk_parent;
+	const struct samsung_ufs_phy_drvdata *drvdata;
+	struct samsung_ufs_phy_cfg **cfg;
+	const struct pmu_isol *isol;
+	u8 lane_cnt;
+	int ufs_phy_state;
+	enum phy_mode mode;
+	bool is_pre_init;
+	bool is_post_init;
+	bool is_pre_pmc;
+	bool is_post_pmc;
+};
+
+static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy *phy)
+{
+	return (struct samsung_ufs_phy *)phy_get_drvdata(phy);
+}
+
+static inline void samsung_ufs_phy_ctrl_isol(
+		struct samsung_ufs_phy *phy, u32 isol)
+{
+	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
+			phy->isol->mask, isol ? 0 : phy->isol->en);
+}
+
+#include "phy-exynos7-ufs.h"
+
+#endif /* _PHY_SAMSUNG_UFS_ */
diff --git a/include/linux/phy/phy-samsung-ufs.h b/include/linux/phy/phy-samsung-ufs.h
new file mode 100644
index 000000000000..1def56207f5d
--- /dev/null
+++ b/include/linux/phy/phy-samsung-ufs.h
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+
+#ifndef _PHY_EXYNOS_UFS_H_
+#define _PHY_EXYNOS_UFS_H_
+
+#include "phy.h"
+
+/* description for PHY calibration */
+enum {
+	/* applicable to any */
+	PWR_DESC_ANY	= 0,
+	/* mode */
+	PWR_DESC_PWM	= 1,
+	PWR_DESC_HS	= 2,
+	/* series */
+	PWR_DESC_SER_A	= 1,
+	PWR_DESC_SER_B	= 2,
+	/* gear */
+	PWR_DESC_G1	= 1,
+	PWR_DESC_G2	= 2,
+	PWR_DESC_G3	= 3,
+	PWR_DESC_G4	= 4,
+	PWR_DESC_G5	= 5,
+	PWR_DESC_G6	= 6,
+	PWR_DESC_G7	= 7,
+	/* field mask */
+	MD_MASK		= 0x3,
+	SR_MASK		= 0x3,
+	GR_MASK		= 0x7,
+};
+
+#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
+				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
+#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
+				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
+#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_ANY)
+#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_B)
+#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_ANY)
+#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_B)
+#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_ANY)
+#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_B)
+#define PWR_MODE_HS_ANY		PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_HS)
+#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_PWM)
+#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_ANY)
+#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
+#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) == PWR_DESC_PWM)
+#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
+#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
+#define COMP_PWR_MODE(a, b)		((a) == (b))
+#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
+					 (((b) >> 4) & GR_MASK))
+#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK) == \
+					 (((b) >> 2) & SR_MASK))
+#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) == ((b) & MD_MASK))
+
+#endif /* _PHY_EXYNOS_UFS_H_ */
-- 
2.17.1

[PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Alim Akhtar]

This patch introduces Samsung UFS PHY driver. This driver
supports to deal with phy calibration and power control
according to UFS host driver's behavior.

Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
---
 drivers/phy/samsung/Kconfig           |   9 +
 drivers/phy/samsung/Makefile          |   1 +
 drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
 drivers/phy/samsung/phy-samsung-ufs.c | 311 ++++++++++++++++++++++++++
 drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
 include/linux/phy/phy-samsung-ufs.h   |  70 ++++++
 6 files changed, 576 insertions(+)
 create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
 create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
 create mode 100644 include/linux/phy/phy-samsung-ufs.h

diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
index 9e483d1fdaf2..fc1e3c17f842 100644
--- a/drivers/phy/samsung/Kconfig
+++ b/drivers/phy/samsung/Kconfig
@@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
 	  Enable PCIe PHY support for Exynos SoC series.
 	  This driver provides PHY interface for Exynos PCIe controller.
 
+config PHY_SAMSUNG_UFS
+	tristate "SAMSUNG SoC series UFS PHY driver"
+	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support the Samsung UFS PHY driver for
+	  Samsung SoCs. This driver provides the interface for UFS
+	  host controller to do PHY related programming.
+
 config PHY_SAMSUNG_USB2
 	tristate "Samsung USB 2.0 PHY driver"
 	depends on HAS_IOMEM
diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
index db9b1aa0de6e..3959100fe8a2 100644
--- a/drivers/phy/samsung/Makefile
+++ b/drivers/phy/samsung/Makefile
@@ -2,6 +2,7 @@
 obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
 obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
 obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
+obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
 obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
 phy-exynos-usb2-y			+= phy-samsung-usb2.o
 phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h b/drivers/phy/samsung/phy-exynos7-ufs.h
new file mode 100644
index 000000000000..da981c1ac040
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos7-ufs.h
@@ -0,0 +1,85 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS PHY driver data for Samsung EXYNOS7 SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ */
+#ifndef _PHY_EXYNOS7_UFS_H_
+#define _PHY_EXYNOS7_UFS_H_
+
+#include "phy-samsung-ufs.h"
+
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
+#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
+
+/* Calibration for phy initialization */
+static const struct samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
+	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
+	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
+	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
+	END_UFS_PHY_CFG
+};
+
+static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
+	END_UFS_PHY_CFG
+};
+
+/* Calibration for HS mode series A/B */
+static const struct samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
+	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
+	/* Setting order: 1st(0x16, 2nd(0x15) */
+	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
+	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
+	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
+	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
+	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
+	END_UFS_PHY_CFG
+};
+
+/* Calibration for HS mode series A/B atfer PMC */
+static const struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
+	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
+	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
+	END_UFS_PHY_CFG
+};
+
+static const struct samsung_ufs_phy_cfg *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
+	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
+	[CFG_POST_INIT]		= exynos7_post_init_cfg,
+	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
+	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
+};
+
+static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
+	.cfg = exynos7_ufs_phy_cfgs,
+	.isol = {
+		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
+		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
+		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
+	},
+};
+
+#endif /* _PHY_EXYNOS7_UFS_H_ */
diff --git a/drivers/phy/samsung/phy-samsung-ufs.c b/drivers/phy/samsung/phy-samsung-ufs.c
new file mode 100644
index 000000000000..2d5db24de49b
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-ufs.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UFS PHY driver for Samsung SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-samsung-ufs.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "phy-samsung-ufs.h"
+
+#define for_each_phy_lane(phy, i) \
+	for (i = 0; i < (phy)->lane_cnt; i++)
+#define for_each_phy_cfg(cfg) \
+	for (; (cfg)->id; (cfg)++)
+
+#define PHY_DEF_LANE_CNT	1
+
+static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
+			const struct samsung_ufs_phy_cfg *cfg, u8 lane)
+{
+	enum {LANE_0, LANE_1}; /* lane index */
+
+	switch (lane) {
+	case LANE_0:
+		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
+		break;
+	case LANE_1:
+		if (cfg->id == PHY_TRSV_BLK)
+			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
+		break;
+	}
+}
+
+int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy)
+{
+	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
+	const unsigned int timeout_us = 100000;
+	const unsigned int sleep_us = 10;
+	u32 val;
+	int err;
+
+	err = readl_poll_timeout(
+			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
+			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
+	if (err) {
+		dev_err(ufs_phy->dev,
+			"failed to get phy pll lock acquisition %d\n", err);
+		goto out;
+	}
+
+	err = readl_poll_timeout(
+			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
+			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
+	if (err) {
+		dev_err(ufs_phy->dev,
+			"failed to get phy cdr lock acquisition %d\n", err);
+		goto out;
+	}
+
+out:
+	return err;
+}
+
+int samsung_ufs_phy_calibrate(struct phy *phy)
+{
+	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
+	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
+	const struct samsung_ufs_phy_cfg *cfg;
+	int i;
+	int err = 0;
+
+	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
+		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
+		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
+							ufs_phy->ufs_phy_state);
+		return -EINVAL;
+	}
+
+	if (ufs_phy->is_pre_init)
+		ufs_phy->is_pre_init = false;
+	if (ufs_phy->is_post_init) {
+		ufs_phy->is_post_init = false;
+		ufs_phy->ufs_phy_state = CFG_POST_INIT;
+	}
+	if (ufs_phy->is_pre_pmc) {
+		ufs_phy->is_pre_pmc = false;
+		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
+	}
+	if (ufs_phy->is_post_pmc) {
+		ufs_phy->is_post_pmc = false;
+		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
+	}
+
+	switch (ufs_phy->ufs_phy_state) {
+	case CFG_PRE_INIT:
+		ufs_phy->is_post_init = true;
+		break;
+	case CFG_POST_INIT:
+		ufs_phy->is_pre_pmc = true;
+		break;
+	case CFG_PRE_PWR_HS:
+		ufs_phy->is_post_pmc = true;
+		break;
+	case CFG_POST_PWR_HS:
+		break;
+	default:
+		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
+	}
+
+	cfg = cfgs[ufs_phy->ufs_phy_state];
+	if (!cfg)
+		goto out;
+
+	for_each_phy_cfg(cfg) {
+		for_each_phy_lane(ufs_phy, i) {
+			samsung_ufs_phy_config(ufs_phy, cfg, i);
+		}
+	}
+
+	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
+		err = samsung_ufs_phy_wait_for_lock_acq(phy);
+out:
+	return err;
+}
+
+static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy)
+{
+	struct clk *child, *parent;
+
+	child = devm_clk_get(phy->dev, "ref_clk");
+	if (IS_ERR(child))
+		dev_err(phy->dev, "failed to get ref_clk clock\n");
+	else
+		phy->ref_clk = child;
+
+	parent = devm_clk_get(phy->dev, "ref_clk_parent");
+	if (IS_ERR(parent))
+		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
+	else
+		phy->ref_clk_parent = parent;
+
+	return clk_set_parent(child, parent);
+}
+
+static int samsung_ufs_phy_init(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+
+	_phy->lane_cnt = phy->attrs.bus_width;
+	_phy->ufs_phy_state = CFG_PRE_INIT;
+
+	_phy->is_pre_init = true;
+	_phy->is_post_init = false;
+	_phy->is_pre_pmc = false;
+	_phy->is_post_pmc = false;
+
+	samsung_ufs_phy_clks_init(_phy);
+
+	samsung_ufs_phy_calibrate(phy);
+
+	return 0;
+}
+
+static int samsung_ufs_phy_power_on(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+	int ret;
+
+	ret = clk_prepare_enable(_phy->ref_clk);
+	if (ret) {
+		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
+				__func__, ret);
+		return ret;
+	}
+
+	samsung_ufs_phy_ctrl_isol(_phy, false);
+	return 0;
+}
+
+static int samsung_ufs_phy_power_off(struct phy *phy)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
+
+	samsung_ufs_phy_ctrl_isol(_phy, true);
+	clk_disable_unprepare(_phy->ref_clk);
+	return 0;
+}
+
+static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
+					enum phy_mode mode, int submode)
+{
+	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
+
+	_phy->mode = PHY_MODE_INVALID;
+
+	if (mode > 0)
+		_phy->mode = mode;
+
+	return 0;
+}
+
+static struct phy_ops samsung_ufs_phy_ops = {
+	.init		= samsung_ufs_phy_init,
+	.power_on	= samsung_ufs_phy_power_on,
+	.power_off	= samsung_ufs_phy_power_off,
+	.calibrate	= samsung_ufs_phy_calibrate,
+	.set_mode	= samsung_ufs_phy_set_mode,
+}
+;
+static const struct of_device_id samsung_ufs_phy_match[];
+
+static int samsung_ufs_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	const struct of_device_id *match;
+	struct samsung_ufs_phy *phy;
+	struct phy *gen_phy;
+	struct phy_provider *phy_provider;
+	const struct samsung_ufs_phy_drvdata *drvdata;
+	int err = 0;
+
+	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
+	if (!match) {
+		err = -EINVAL;
+		dev_err(dev, "failed to get match_node\n");
+		goto out;
+	}
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		err = -ENOMEM;
+		goto out;
+	}
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-pma");
+	phy->reg_pma = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy->reg_pma)) {
+		err = PTR_ERR(phy->reg_pma);
+		goto out;
+	}
+
+	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
+				dev->of_node, "samsung,pmu-syscon");
+	if (IS_ERR(phy->reg_pmu)) {
+		err = PTR_ERR(phy->reg_pmu);
+		dev_err(dev, "failed syscon remap for pmu\n");
+		goto out;
+	}
+
+	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
+	if (IS_ERR(gen_phy)) {
+		err = PTR_ERR(gen_phy);
+		dev_err(dev, "failed to create PHY for ufs-phy\n");
+		goto out;
+	}
+
+	drvdata = match->data;
+	phy->dev = dev;
+	phy->drvdata = drvdata;
+	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
+	phy->isol = &drvdata->isol;
+	phy->lane_cnt = PHY_DEF_LANE_CNT;
+
+	phy_set_drvdata(gen_phy, phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		err = PTR_ERR(phy_provider);
+		dev_err(dev, "failed to register phy-provider\n");
+		goto out;
+	}
+out:
+	return err;
+}
+
+static const struct of_device_id samsung_ufs_phy_match[] = {
+	{
+		.compatible = "samsung,exynos7-ufs-phy",
+		.data = &exynos7_ufs_phy,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
+
+static struct platform_driver samsung_ufs_phy_driver = {
+	.probe  = samsung_ufs_phy_probe,
+	.driver = {
+		.name = "samsung-ufs-phy",
+		.of_match_table = samsung_ufs_phy_match,
+	},
+};
+module_platform_driver(samsung_ufs_phy_driver);
+MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
+MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
+MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/samsung/phy-samsung-ufs.h b/drivers/phy/samsung/phy-samsung-ufs.h
new file mode 100644
index 000000000000..d0ae2b416b2b
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-ufs.h
@@ -0,0 +1,100 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS PHY driver for Samsung EXYNOS SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+#ifndef _PHY_SAMSUNG_UFS_
+#define _PHY_SAMSUNG_UFS_
+
+#define PHY_COMN_BLK	1
+#define PHY_TRSV_BLK	2
+#define END_UFS_PHY_CFG { 0 }
+#define PHY_TRSV_CH_OFFSET	0x30
+#define PHY_APB_ADDR(off)	((off) << 2)
+
+#define PHY_COMN_REG_CFG(o, v, d) {	\
+	.off_0 = PHY_APB_ADDR((o)),	\
+	.off_1 = 0,		\
+	.val = (v),		\
+	.desc = (d),		\
+	.id = PHY_COMN_BLK,	\
+}
+
+#define PHY_TRSV_REG_CFG(o, v, d) {	\
+	.off_0 = PHY_APB_ADDR((o)),	\
+	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
+	.val = (v),		\
+	.desc = (d),		\
+	.id = PHY_TRSV_BLK,	\
+}
+
+/* UFS PHY registers */
+#define PHY_PLL_LOCK_STATUS	0x1e
+#define PHY_CDR_LOCK_STATUS	0x5e
+
+#define PHY_PLL_LOCK_BIT	BIT(5)
+#define PHY_CDR_LOCK_BIT	BIT(4)
+
+/* PHY calibration point/state */
+enum {
+	CFG_PRE_INIT,
+	CFG_POST_INIT,
+	CFG_PRE_PWR_HS,
+	CFG_POST_PWR_HS,
+	CFG_TAG_MAX,
+};
+
+struct samsung_ufs_phy_cfg {
+	u32 off_0;
+	u32 off_1;
+	u32 val;
+	u8 desc;
+	u8 id;
+};
+
+struct samsung_ufs_phy_drvdata {
+	const struct samsung_ufs_phy_cfg **cfg;
+	struct pmu_isol {
+		u32 offset;
+		u32 mask;
+		u32 en;
+	} isol;
+};
+
+struct samsung_ufs_phy {
+	struct device *dev;
+	void __iomem *reg_pma;
+	struct regmap *reg_pmu;
+	struct clk *ref_clk;
+	struct clk *ref_clk_parent;
+	const struct samsung_ufs_phy_drvdata *drvdata;
+	struct samsung_ufs_phy_cfg **cfg;
+	const struct pmu_isol *isol;
+	u8 lane_cnt;
+	int ufs_phy_state;
+	enum phy_mode mode;
+	bool is_pre_init;
+	bool is_post_init;
+	bool is_pre_pmc;
+	bool is_post_pmc;
+};
+
+static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy *phy)
+{
+	return (struct samsung_ufs_phy *)phy_get_drvdata(phy);
+}
+
+static inline void samsung_ufs_phy_ctrl_isol(
+		struct samsung_ufs_phy *phy, u32 isol)
+{
+	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
+			phy->isol->mask, isol ? 0 : phy->isol->en);
+}
+
+#include "phy-exynos7-ufs.h"
+
+#endif /* _PHY_SAMSUNG_UFS_ */
diff --git a/include/linux/phy/phy-samsung-ufs.h b/include/linux/phy/phy-samsung-ufs.h
new file mode 100644
index 000000000000..1def56207f5d
--- /dev/null
+++ b/include/linux/phy/phy-samsung-ufs.h
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
+ *
+ * Copyright (C) 2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+
+#ifndef _PHY_EXYNOS_UFS_H_
+#define _PHY_EXYNOS_UFS_H_
+
+#include "phy.h"
+
+/* description for PHY calibration */
+enum {
+	/* applicable to any */
+	PWR_DESC_ANY	= 0,
+	/* mode */
+	PWR_DESC_PWM	= 1,
+	PWR_DESC_HS	= 2,
+	/* series */
+	PWR_DESC_SER_A	= 1,
+	PWR_DESC_SER_B	= 2,
+	/* gear */
+	PWR_DESC_G1	= 1,
+	PWR_DESC_G2	= 2,
+	PWR_DESC_G3	= 3,
+	PWR_DESC_G4	= 4,
+	PWR_DESC_G5	= 5,
+	PWR_DESC_G6	= 6,
+	PWR_DESC_G7	= 7,
+	/* field mask */
+	MD_MASK		= 0x3,
+	SR_MASK		= 0x3,
+	GR_MASK		= 0x7,
+};
+
+#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
+				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
+#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
+				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
+#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_ANY)
+#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_B)
+#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_ANY)
+#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_B)
+#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_ANY)
+#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_A)
+#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_B)
+#define PWR_MODE_HS_ANY		PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_HS)
+#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_PWM)
+#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
+					 PWR_DESC_ANY, PWR_DESC_ANY)
+#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
+#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) == PWR_DESC_PWM)
+#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
+#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
+#define COMP_PWR_MODE(a, b)		((a) == (b))
+#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
+					 (((b) >> 4) & GR_MASK))
+#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK) == \
+					 (((b) >> 2) & SR_MASK))
+#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) == ((b) & MD_MASK))
+
+#endif /* _PHY_EXYNOS_UFS_H_ */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 3/5] Documentation: devicetree: ufs: Add DT bindings for exynos UFS host controller

[Alim Akhtar]

This adds Exynos Universal Flash Storage (UFS) Host Controller DT bindings.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../devicetree/bindings/ufs/ufs-exynos.txt    | 104 ++++++++++++++++++
 1 file changed, 104 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt

diff --git a/Documentation/devicetree/bindings/ufs/ufs-exynos.txt b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
new file mode 100644
index 000000000000..08e2d1497b1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
@@ -0,0 +1,104 @@
+* Exynos Universal Flash Storage (UFS) Host Controller
+
+UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible        : compatible name, contains "samsung,exynos7-ufs"
+- interrupts        : <interrupt mapping for UFS host controller IRQ>
+- reg               : Should contain HCI, vendor specific, UNIPRO and
+		      UFS protector address space
+- reg-names	    : "hci", "vs_hci", "unipro", "ufsp";
+
+Optional properties:
+- vdd-hba-supply        : phandle to UFS host controller supply regulator node
+- vcc-supply            : phandle to VCC supply regulator node
+- vccq-supply           : phandle to VCCQ supply regulator node
+- vccq2-supply          : phandle to VCCQ2 supply regulator node
+- vcc-supply-1p8        : For embedded UFS devices, valid VCC range is 1.7-1.95V
+                          or 2.7-3.6V. This boolean property when set, specifies
+			  to use low voltage range of 1.7-1.95V. Note for external
+			  UFS cards this property is invalid and valid VCC range is
+			  always 2.7-3.6V.
+- vcc-max-microamp      : specifies max. load that can be drawn from vcc supply
+- vccq-max-microamp     : specifies max. load that can be drawn from vccq supply
+- vccq2-max-microamp    : specifies max. load that can be drawn from vccq2 supply
+- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator
+
+- clocks                : List of phandle and clock specifier pairs
+- clock-names           : List of clock input name strings sorted in the same
+                          order as the clocks property.
+			  "core", "sclk_unipro_main", "ref" and ref_parent
+
+- freq-table-hz		: Array of <min max> operating frequencies stored in the same
+			  order as the clocks property. If this property is not
+			  defined or a value in the array is "0" then it is assumed
+			  that the frequency is set by the parent clock or a
+			  fixed rate clock source.
+- pclk-freq-avail-range : specifies available frequency range(min/max) for APB clock
+- ufs,pwr-attr-mode : specifies mode value for power mode change, possible values are
+			"FAST", "SLOW", "FAST_auto" and "SLOW_auto"
+- ufs,pwr-attr-lane : specifies lane count value for power mode change
+		      allowed values are 1 or 2
+- ufs,pwr-attr-gear : specifies gear count value for power mode change
+		      allowed values are 1 or 2
+- ufs,pwr-attr-hs-series : specifies HS rate series for power mode change
+			   can be one of "HS_rate_b" or "HS_rate_a"
+- ufs,pwr-local-l2-timer : specifies array of local UNIPRO L2 timer values
+			   3 timers supported
+			   <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs,pwr-remote-l2-timer : specifies array of remote UNIPRO L2 timer values
+			   3 timers supported
+			   <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs-rx-adv-fine-gran-sup_en : specifies support of fine granularity of MPHY,
+			      this is a boolean property.
+- ufs-rx-adv-fine-gran-step : specifies granularity steps of MPHY,
+			      allowed step size is 0 to 3
+- ufs-rx-adv-min-activate-time-cap : specifies rx advanced minimum activate time of MPHY
+				     range is 1 to 9
+- ufs-pa-granularity : specifies Granularity for PA_TActivate and PA_Hibern8Time
+- ufs-pa-tacctivate : specifies time to wake-up remote M-RX
+- ufs-pa-hibern8time : specifies minimum time to wait in HIBERN8 state
+
+Note: If above properties are not defined it can be assumed that the supply
+regulators or clocks are always on.
+
+Example:
+	ufshc@0x15570000 {
+		compatible = "samsung,exynos7-ufs";
+		reg = <0x15570000 0x100>,
+		      <0x15570100 0x100>,
+		      <0x15571000 0x200>,
+		      <0x15572000 0x300>;
+		reg-names = "hci", "vs_hci", "unipro", "ufsp";
+		interrupts = <0 200 0>;
+
+		vdd-hba-supply = <&xxx_reg0>;
+		vdd-hba-fixed-regulator;
+		vcc-supply = <&xxx_reg1>;
+		vcc-supply-1p8;
+		vccq-supply = <&xxx_reg2>;
+		vccq2-supply = <&xxx_reg3>;
+		vcc-max-microamp = 500000;
+		vccq-max-microamp = 200000;
+		vccq2-max-microamp = 200000;
+
+		clocks = <&core 0>, <&ref 0>, <&iface 0>;
+		clock-names = "core", "sclk_unipro_main", "ref", "ref_parent";
+		freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
+
+		pclk-freq-avail-range = <70000000 133000000>;
+
+		ufs,pwr-attr-mode = "FAST";
+		ufs,pwr-attr-lane = <2>;
+		ufs,pwr-attr-gear = <2>;
+		ufs,pwr-attr-hs-series = "HS_rate_b";
+		ufs,pwr-local-l2-timer = <8000 28000 20000>;
+		ufs,pwr-remote-l2-timer = <12000 32000 16000>;
+		ufs-rx-adv-fine-gran-sup_en = <1>;
+		ufs-rx-adv-fine-gran-step = <3>;
+		ufs-rx-adv-min-activate-time-cap = <9>;
+		ufs-pa-granularity = <6>;
+		ufs-pa-tacctivate = <6>;
+		ufs-pa-hibern8time = <20>;
+	};
-- 
2.17.1

[PATCH v3 3/5] Documentation: devicetree: ufs: Add DT bindings for exynos UFS host controller

[Alim Akhtar]

This adds Exynos Universal Flash Storage (UFS) Host Controller DT bindings.

Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../devicetree/bindings/ufs/ufs-exynos.txt    | 104 ++++++++++++++++++
 1 file changed, 104 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt

diff --git a/Documentation/devicetree/bindings/ufs/ufs-exynos.txt b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
new file mode 100644
index 000000000000..08e2d1497b1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
@@ -0,0 +1,104 @@
+* Exynos Universal Flash Storage (UFS) Host Controller
+
+UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible        : compatible name, contains "samsung,exynos7-ufs"
+- interrupts        : <interrupt mapping for UFS host controller IRQ>
+- reg               : Should contain HCI, vendor specific, UNIPRO and
+		      UFS protector address space
+- reg-names	    : "hci", "vs_hci", "unipro", "ufsp";
+
+Optional properties:
+- vdd-hba-supply        : phandle to UFS host controller supply regulator node
+- vcc-supply            : phandle to VCC supply regulator node
+- vccq-supply           : phandle to VCCQ supply regulator node
+- vccq2-supply          : phandle to VCCQ2 supply regulator node
+- vcc-supply-1p8        : For embedded UFS devices, valid VCC range is 1.7-1.95V
+                          or 2.7-3.6V. This boolean property when set, specifies
+			  to use low voltage range of 1.7-1.95V. Note for external
+			  UFS cards this property is invalid and valid VCC range is
+			  always 2.7-3.6V.
+- vcc-max-microamp      : specifies max. load that can be drawn from vcc supply
+- vccq-max-microamp     : specifies max. load that can be drawn from vccq supply
+- vccq2-max-microamp    : specifies max. load that can be drawn from vccq2 supply
+- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator
+
+- clocks                : List of phandle and clock specifier pairs
+- clock-names           : List of clock input name strings sorted in the same
+                          order as the clocks property.
+			  "core", "sclk_unipro_main", "ref" and ref_parent
+
+- freq-table-hz		: Array of <min max> operating frequencies stored in the same
+			  order as the clocks property. If this property is not
+			  defined or a value in the array is "0" then it is assumed
+			  that the frequency is set by the parent clock or a
+			  fixed rate clock source.
+- pclk-freq-avail-range : specifies available frequency range(min/max) for APB clock
+- ufs,pwr-attr-mode : specifies mode value for power mode change, possible values are
+			"FAST", "SLOW", "FAST_auto" and "SLOW_auto"
+- ufs,pwr-attr-lane : specifies lane count value for power mode change
+		      allowed values are 1 or 2
+- ufs,pwr-attr-gear : specifies gear count value for power mode change
+		      allowed values are 1 or 2
+- ufs,pwr-attr-hs-series : specifies HS rate series for power mode change
+			   can be one of "HS_rate_b" or "HS_rate_a"
+- ufs,pwr-local-l2-timer : specifies array of local UNIPRO L2 timer values
+			   3 timers supported
+			   <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs,pwr-remote-l2-timer : specifies array of remote UNIPRO L2 timer values
+			   3 timers supported
+			   <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs-rx-adv-fine-gran-sup_en : specifies support of fine granularity of MPHY,
+			      this is a boolean property.
+- ufs-rx-adv-fine-gran-step : specifies granularity steps of MPHY,
+			      allowed step size is 0 to 3
+- ufs-rx-adv-min-activate-time-cap : specifies rx advanced minimum activate time of MPHY
+				     range is 1 to 9
+- ufs-pa-granularity : specifies Granularity for PA_TActivate and PA_Hibern8Time
+- ufs-pa-tacctivate : specifies time to wake-up remote M-RX
+- ufs-pa-hibern8time : specifies minimum time to wait in HIBERN8 state
+
+Note: If above properties are not defined it can be assumed that the supply
+regulators or clocks are always on.
+
+Example:
+	ufshc@0x15570000 {
+		compatible = "samsung,exynos7-ufs";
+		reg = <0x15570000 0x100>,
+		      <0x15570100 0x100>,
+		      <0x15571000 0x200>,
+		      <0x15572000 0x300>;
+		reg-names = "hci", "vs_hci", "unipro", "ufsp";
+		interrupts = <0 200 0>;
+
+		vdd-hba-supply = <&xxx_reg0>;
+		vdd-hba-fixed-regulator;
+		vcc-supply = <&xxx_reg1>;
+		vcc-supply-1p8;
+		vccq-supply = <&xxx_reg2>;
+		vccq2-supply = <&xxx_reg3>;
+		vcc-max-microamp = 500000;
+		vccq-max-microamp = 200000;
+		vccq2-max-microamp = 200000;
+
+		clocks = <&core 0>, <&ref 0>, <&iface 0>;
+		clock-names = "core", "sclk_unipro_main", "ref", "ref_parent";
+		freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>;
+
+		pclk-freq-avail-range = <70000000 133000000>;
+
+		ufs,pwr-attr-mode = "FAST";
+		ufs,pwr-attr-lane = <2>;
+		ufs,pwr-attr-gear = <2>;
+		ufs,pwr-attr-hs-series = "HS_rate_b";
+		ufs,pwr-local-l2-timer = <8000 28000 20000>;
+		ufs,pwr-remote-l2-timer = <12000 32000 16000>;
+		ufs-rx-adv-fine-gran-sup_en = <1>;
+		ufs-rx-adv-fine-gran-step = <3>;
+		ufs-rx-adv-min-activate-time-cap = <9>;
+		ufs-pa-granularity = <6>;
+		ufs-pa-tacctivate = <6>;
+		ufs-pa-hibern8time = <20>;
+	};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Alim Akhtar]

This patch introduces Exynos UFS host controller driver,
which mainly handles vendor-specific operations including
link startup, power mode change and hibernation/unhibernation.

Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
[robot: drivers/scsi/ufs/ufs-exynos.c:931:8-10:
 WARNING: possible condition with no effect (if == else)
]
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/Kconfig      |   12 +
 drivers/scsi/ufs/Makefile     |    1 +
 drivers/scsi/ufs/ufs-exynos.c | 1399 +++++++++++++++++++++++++++++++++
 drivers/scsi/ufs/ufs-exynos.h |  268 +++++++
 drivers/scsi/ufs/unipro.h     |   41 +
 5 files changed, 1721 insertions(+)
 create mode 100644 drivers/scsi/ufs/ufs-exynos.c
 create mode 100644 drivers/scsi/ufs/ufs-exynos.h

diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig
index d14c2243e02a..8fda908bce5b 100644
--- a/drivers/scsi/ufs/Kconfig
+++ b/drivers/scsi/ufs/Kconfig
@@ -160,3 +160,15 @@ config SCSI_UFS_BSG
 
 	  Select this if you need a bsg device node for your UFS controller.
 	  If unsure, say N.
+
+config SCSI_UFS_EXYNOS
+	bool "EXYNOS specific hooks to UFS controller platform driver"
+	depends on SCSI_UFSHCD_PLATFORM && ARCH_EXYNOS || COMPILE_TEST
+	select PHY_EXYNOS_UFS
+	help
+	  This selects the EXYNOS specific additions to UFSHCD platform driver.
+	  UFS host on EXYNOS includes HCI and UNIPRO layer, and associates with
+	  UFS-PHY driver.
+
+	  Select this if you have UFS host controller on EXYNOS chipset.
+	  If unsure, say N.
diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile
index 94c6c5d7334b..f0c5b95ec9cc 100644
--- a/drivers/scsi/ufs/Makefile
+++ b/drivers/scsi/ufs/Makefile
@@ -4,6 +4,7 @@ obj-$(CONFIG_SCSI_UFS_DWC_TC_PCI) += tc-dwc-g210-pci.o ufshcd-dwc.o tc-dwc-g210.
 obj-$(CONFIG_SCSI_UFS_DWC_TC_PLATFORM) += tc-dwc-g210-pltfrm.o ufshcd-dwc.o tc-dwc-g210.o
 obj-$(CONFIG_SCSI_UFS_CDNS_PLATFORM) += cdns-pltfrm.o
 obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
+obj-$(CONFIG_SCSI_UFS_EXYNOS) += ufs-exynos.o
 obj-$(CONFIG_SCSI_UFSHCD) += ufshcd-core.o
 ufshcd-core-y				+= ufshcd.o ufs-sysfs.o
 ufshcd-core-$(CONFIG_SCSI_UFS_BSG)	+= ufs_bsg.o
diff --git a/drivers/scsi/ufs/ufs-exynos.c b/drivers/scsi/ufs/ufs-exynos.c
new file mode 100644
index 000000000000..fe8f67220768
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-exynos.c
@@ -0,0 +1,1399 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UFS Host Controller driver for Exynos specific extensions
+ *
+ * Copyright (C) 2014-2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon  <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy-samsung-ufs.h>
+#include <linux/platform_device.h>
+
+#include "ufshcd.h"
+#include "ufshcd-pltfrm.h"
+#include "ufshci.h"
+#include "unipro.h"
+
+#include "ufs-exynos.h"
+
+/*
+ * Exynos's Vendor specific registers for UFSHCI
+ */
+#define HCI_TXPRDT_ENTRY_SIZE	0x00
+#define PRDT_PREFECT_EN		BIT(31)
+#define PRDT_SET_SIZE(x)	((x) & 0x1F)
+#define HCI_RXPRDT_ENTRY_SIZE	0x04
+#define HCI_1US_TO_CNT_VAL	0x0C
+#define CNT_VAL_1US_MASK	0x3FF
+#define HCI_UTRL_NEXUS_TYPE	0x40
+#define HCI_UTMRL_NEXUS_TYPE	0x44
+#define HCI_SW_RST		0x50
+#define UFS_LINK_SW_RST		BIT(0)
+#define UFS_UNIPRO_SW_RST	BIT(1)
+#define UFS_SW_RST_MASK		(UFS_UNIPRO_SW_RST | UFS_LINK_SW_RST)
+#define HCI_DATA_REORDER	0x60
+#define HCI_UNIPRO_APB_CLK_CTRL	0x68
+#define UNIPRO_APB_CLK(v, x)	(((v) & ~0xF) | ((x) & 0xF))
+#define HCI_AXIDMA_RWDATA_BURST_LEN	0x6C
+#define HCI_GPIO_OUT		0x70
+#define HCI_ERR_EN_PA_LAYER	0x78
+#define HCI_ERR_EN_DL_LAYER	0x7C
+#define HCI_ERR_EN_N_LAYER	0x80
+#define HCI_ERR_EN_T_LAYER	0x84
+#define HCI_ERR_EN_DME_LAYER	0x88
+#define HCI_CLKSTOP_CTRL	0xB0
+#define REFCLK_STOP		BIT(2)
+#define UNIPRO_MCLK_STOP	BIT(1)
+#define UNIPRO_PCLK_STOP	BIT(0)
+#define CLK_STOP_MASK		(REFCLK_STOP |\
+				 UNIPRO_MCLK_STOP |\
+				 UNIPRO_PCLK_STOP)
+#define HCI_MISC		0xB4
+#define REFCLK_CTRL_EN		BIT(7)
+#define UNIPRO_PCLK_CTRL_EN	BIT(6)
+#define UNIPRO_MCLK_CTRL_EN	BIT(5)
+#define HCI_CORECLK_CTRL_EN	BIT(4)
+#define CLK_CTRL_EN_MASK	(REFCLK_CTRL_EN |\
+				 UNIPRO_PCLK_CTRL_EN |\
+				 UNIPRO_MCLK_CTRL_EN)
+/* Device fatal error */
+#define DFES_ERR_EN		BIT(31)
+#define DFES_DEF_L2_ERRS	(UIC_DATA_LINK_LAYER_ERROR_RX_BUF_OF |\
+				 UIC_DATA_LINK_LAYER_ERROR_PA_INIT)
+#define DFES_DEF_L3_ERRS	(UIC_NETWORK_UNSUPPORTED_HEADER_TYPE |\
+				 UIC_NETWORK_BAD_DEVICEID_ENC |\
+				 UIC_NETWORK_LHDR_TRAP_PACKET_DROPPING)
+#define DFES_DEF_L4_ERRS	(UIC_TRANSPORT_UNSUPPORTED_HEADER_TYPE |\
+				 UIC_TRANSPORT_UNKNOWN_CPORTID |\
+				 UIC_TRANSPORT_NO_CONNECTION_RX |\
+				 UIC_TRANSPORT_BAD_TC)
+
+enum {
+	UNIPRO_L1_5 = 0,/* PHY Adapter */
+	UNIPRO_L2,	/* Data Link */
+	UNIPRO_L3,	/* Network */
+	UNIPRO_L4,	/* Transport */
+	UNIPRO_DME,	/* DME */
+};
+
+/*
+ * UNIPRO registers
+ */
+#define UNIPRO_COMP_VERSION			0x000
+#define UNIPRO_DME_PWR_REQ			0x090
+#define UNIPRO_DME_PWR_REQ_POWERMODE		0x094
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER0	0x098
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER1	0x09C
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER2	0x0A0
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER0	0x0A4
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER1	0x0A8
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER2	0x0AC
+
+/*
+ * UFS Protector registers
+ */
+#define UFSPRSECURITY	0x010
+#define NSSMU		BIT(14)
+#define UFSPSBEGIN0	0x200
+#define UFSPSEND0	0x204
+#define UFSPSLUN0	0x208
+#define UFSPSCTRL0	0x20C
+
+static void exynos_ufs_auto_ctrl_hcc(struct exynos_ufs *ufs, bool en);
+static void exynos_ufs_ctrl_clkstop(struct exynos_ufs *ufs, bool en);
+
+static inline void exynos_ufs_enable_auto_ctrl_hcc(struct exynos_ufs *ufs)
+{
+	exynos_ufs_auto_ctrl_hcc(ufs, true);
+}
+
+static inline void exynos_ufs_disable_auto_ctrl_hcc(struct exynos_ufs *ufs)
+{
+	exynos_ufs_auto_ctrl_hcc(ufs, false);
+}
+
+static inline void exynos_ufs_disable_auto_ctrl_hcc_save(
+					struct exynos_ufs *ufs, u32 *val)
+{
+	*val = hci_readl(ufs, HCI_MISC);
+	exynos_ufs_auto_ctrl_hcc(ufs, false);
+}
+
+static inline void exynos_ufs_auto_ctrl_hcc_restore(
+					struct exynos_ufs *ufs, u32 *val)
+{
+	hci_writel(ufs, *val, HCI_MISC);
+}
+
+static inline void exynos_ufs_gate_clks(struct exynos_ufs *ufs)
+{
+	exynos_ufs_ctrl_clkstop(ufs, true);
+}
+
+static inline void exynos_ufs_ungate_clks(struct exynos_ufs *ufs)
+{
+	exynos_ufs_ctrl_clkstop(ufs, false);
+}
+
+static int exynos7_ufs_drv_init(struct device *dev, struct exynos_ufs *ufs)
+{
+	return 0;
+}
+
+static int exynos7_ufs_pre_link(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+	for_each_ufs_tx_lane(ufs, i)
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x297, i), 0x17);
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x362, i), 0xff);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x363, i), 0x00);
+	}
+	exynos_ufs_disable_ov_tm(hba);
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN), 0xf);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN), 0xf);
+	for_each_ufs_tx_lane(ufs, i)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB_SEL(TX_HIBERN8_CONTROL, i), 0x0);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_TXPHY_CFGUPDT), 0x1);
+	udelay(1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE), val | (1 << 12));
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_SKIP_RESET_PHY), 0x1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_SKIP_LINE_RESET), 0x1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_LINE_RESET_REQ), 0x1);
+	udelay(1600);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE), val);
+
+	return 0;
+}
+
+static int exynos7_ufs_post_link(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+	for_each_ufs_tx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x28b, i), 0x83);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x29a, i), 0x07);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x277, i),
+			TX_LINERESET_N(exynos_ufs_calc_time_cntr(ufs, 200000)));
+	}
+	exynos_ufs_disable_ov_tm(hba);
+
+	exynos_ufs_enable_dbg_mode(hba);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_SAVECONFIGTIME), 0xbb8);
+	exynos_ufs_disable_dbg_mode(hba);
+
+	return 0;
+}
+
+static int exynos7_ufs_pre_pwr_change(struct exynos_ufs *ufs,
+						struct uic_pwr_mode *pwr)
+{
+	unipro_writel(ufs, 0x22, UNIPRO_DBG_FORCE_DME_CTRL_STATE);
+
+	return 0;
+}
+
+static int exynos7_ufs_post_pwr_change(struct exynos_ufs *ufs,
+						struct uic_pwr_mode *pwr)
+{
+	struct ufs_hba *hba = ufs->hba;
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_RXPHY_CFGUPDT), 0x1);
+
+	if (pwr->lane == 1) {
+		exynos_ufs_enable_dbg_mode(hba);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_CONNECTEDTXDATALANES), 0x1);
+		exynos_ufs_disable_dbg_mode(hba);
+	}
+
+	return 0;
+}
+
+/**
+ * exynos_ufs_auto_ctrl_hcc - HCI core clock control by h/w
+ * Control should be disabled in the below cases
+ * - Before host controller S/W reset
+ * - Access to UFS protector's register
+ */
+static void exynos_ufs_auto_ctrl_hcc(struct exynos_ufs *ufs, bool en)
+{
+	u32 misc = hci_readl(ufs, HCI_MISC);
+
+	if (en)
+		hci_writel(ufs, misc | HCI_CORECLK_CTRL_EN, HCI_MISC);
+	else
+		hci_writel(ufs, misc & ~HCI_CORECLK_CTRL_EN, HCI_MISC);
+}
+
+static void exynos_ufs_ctrl_clkstop(struct exynos_ufs *ufs, bool en)
+{
+	u32 ctrl = hci_readl(ufs, HCI_CLKSTOP_CTRL);
+	u32 misc = hci_readl(ufs, HCI_MISC);
+
+	if (en) {
+		hci_writel(ufs, misc | CLK_CTRL_EN_MASK, HCI_MISC);
+		hci_writel(ufs, ctrl | CLK_STOP_MASK, HCI_CLKSTOP_CTRL);
+	} else {
+		hci_writel(ufs, ctrl & ~CLK_STOP_MASK, HCI_CLKSTOP_CTRL);
+		hci_writel(ufs, misc & ~CLK_CTRL_EN_MASK, HCI_MISC);
+	}
+}
+
+static int exynos_ufs_get_clk_info(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct list_head *head = &hba->clk_list_head;
+	struct ufs_clk_info *clki;
+	u32 pclk_rate;
+	u32 f_min, f_max;
+	u8 div = 0;
+	int ret = 0;
+
+	if (!head || list_empty(head))
+		goto out;
+
+	list_for_each_entry(clki, head, list) {
+		if (!IS_ERR(clki->clk)) {
+			if (!strcmp(clki->name, "core_clk"))
+				ufs->clk_hci_core = clki->clk;
+			else if (!strcmp(clki->name, "sclk_unipro_main"))
+				ufs->clk_unipro_main = clki->clk;
+		}
+	}
+
+	if (!ufs->clk_hci_core || !ufs->clk_unipro_main) {
+		dev_err(hba->dev, "failed to get clk info\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ufs->mclk_rate = clk_get_rate(ufs->clk_unipro_main);
+	pclk_rate = clk_get_rate(ufs->clk_hci_core);
+	f_min = ufs->pclk_avail_min;
+	f_max = ufs->pclk_avail_max;
+
+	if (ufs->opts & EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL) {
+		do {
+			pclk_rate /= (div + 1);
+
+			if (pclk_rate <= f_max)
+				break;
+			div++;
+		} while (pclk_rate >= f_min);
+	}
+
+	if (unlikely(pclk_rate < f_min || pclk_rate > f_max)) {
+		dev_err(hba->dev, "not available pclk range %d\n", pclk_rate);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ufs->pclk_rate = pclk_rate;
+	ufs->pclk_div = div;
+
+out:
+	return ret;
+}
+
+static void exynos_ufs_set_unipro_pclk_div(struct exynos_ufs *ufs)
+{
+	if (ufs->opts & EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL) {
+		u32 val;
+
+		val = hci_readl(ufs, HCI_UNIPRO_APB_CLK_CTRL);
+		hci_writel(ufs, UNIPRO_APB_CLK(val, ufs->pclk_div),
+			   HCI_UNIPRO_APB_CLK_CTRL);
+	}
+}
+
+static void exynos_ufs_set_pwm_clk_div(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(CMN_PWM_CLK_CTRL), attr->cmn_pwm_clk_ctrl);
+}
+
+static void exynos_ufs_calc_pwm_clk_div(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	const unsigned int div = 30, mult = 20;
+	const unsigned long pwm_min = 3 * 1000 * 1000;
+	const unsigned long pwm_max = 9 * 1000 * 1000;
+	const int divs[] = {32, 16, 8, 4};
+	unsigned long clk = 0, _clk, clk_period;
+	int i = 0, clk_idx = -1;
+
+	clk_period = UNIPRO_PCLK_PERIOD(ufs);
+	for (i = 0; i < ARRAY_SIZE(divs); i++) {
+		_clk = NSEC_PER_SEC * mult / (clk_period * divs[i] * div);
+		if (_clk >= pwm_min && _clk <= pwm_max) {
+			if (_clk > clk) {
+				clk_idx = i;
+				clk = _clk;
+			}
+		}
+	}
+
+	if (clk_idx == -1) {
+		ufshcd_dme_get(hba, UIC_ARG_MIB(CMN_PWM_CLK_CTRL), &clk_idx);
+		dev_err(hba->dev,
+			"failed to decide pwm clock divider, will not change\n");
+	}
+
+	attr->cmn_pwm_clk_ctrl = clk_idx & PWM_CLK_CTRL_MASK;
+}
+
+long exynos_ufs_calc_time_cntr(struct exynos_ufs *ufs, long period)
+{
+	const int precise = 10;
+	long pclk_rate = ufs->pclk_rate;
+	long clk_period, fraction;
+
+	clk_period = UNIPRO_PCLK_PERIOD(ufs);
+	fraction = ((NSEC_PER_SEC % pclk_rate) * precise) / pclk_rate;
+
+	return (period * precise) / ((clk_period * precise) + fraction);
+}
+
+static void exynos_ufs_specify_phy_time_attr(struct exynos_ufs *ufs)
+{
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	struct ufs_phy_time_cfg *t_cfg = &ufs->t_cfg;
+
+	t_cfg->tx_linereset_p =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_dif_p_nsec);
+	t_cfg->tx_linereset_n =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_dif_n_nsec);
+	t_cfg->tx_high_z_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_high_z_cnt_nsec);
+	t_cfg->tx_base_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_base_unit_nsec);
+	t_cfg->tx_gran_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_gran_unit_nsec);
+	t_cfg->tx_sleep_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_sleep_cnt);
+
+	t_cfg->rx_linereset =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_dif_p_nsec);
+	t_cfg->rx_hibern8_wait =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_hibern8_wait_nsec);
+	t_cfg->rx_base_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_base_unit_nsec);
+	t_cfg->rx_gran_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_gran_unit_nsec);
+	t_cfg->rx_sleep_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_sleep_cnt);
+	t_cfg->rx_stall_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_stall_cnt);
+}
+
+static void exynos_ufs_config_phy_time_attr(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct ufs_phy_time_cfg *t_cfg = &ufs->t_cfg;
+	int i;
+
+	exynos_ufs_set_pwm_clk_div(ufs);
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_FILLER_ENABLE, i),
+				ufs->drv_data->uic_attr->rx_filler_enable);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_LINERESET_VAL, i),
+				RX_LINERESET(t_cfg->rx_linereset));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_BASE_NVAL_07_00, i),
+				RX_BASE_NVAL_L(t_cfg->rx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_BASE_NVAL_15_08, i),
+				RX_BASE_NVAL_H(t_cfg->rx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_GRAN_NVAL_07_00, i),
+				RX_GRAN_NVAL_L(t_cfg->rx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_GRAN_NVAL_10_08, i),
+				RX_GRAN_NVAL_H(t_cfg->rx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_OV_SLEEP_CNT_TIMER, i),
+				RX_OV_SLEEP_CNT(t_cfg->rx_sleep_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_OV_STALL_CNT_TIMER, i),
+				RX_OV_STALL_CNT(t_cfg->rx_stall_cnt));
+	}
+
+	for_each_ufs_tx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_LINERESET_P_VAL, i),
+				TX_LINERESET_P(t_cfg->tx_linereset_p));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_HIGH_Z_CNT_07_00, i),
+				TX_HIGH_Z_CNT_L(t_cfg->tx_high_z_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_HIGH_Z_CNT_11_08, i),
+				TX_HIGH_Z_CNT_H(t_cfg->tx_high_z_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_BASE_NVAL_07_00, i),
+				TX_BASE_NVAL_L(t_cfg->tx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_BASE_NVAL_15_08, i),
+				TX_BASE_NVAL_H(t_cfg->tx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_GRAN_NVAL_07_00, i),
+				TX_GRAN_NVAL_L(t_cfg->tx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_GRAN_NVAL_10_08, i),
+				TX_GRAN_NVAL_H(t_cfg->tx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_OV_SLEEP_CNT_TIMER, i),
+				TX_OV_H8_ENTER_EN |
+				TX_OV_SLEEP_CNT(t_cfg->tx_sleep_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_MIN_ACTIVATETIME, i),
+				ufs->drv_data->uic_attr->tx_min_activatetime);
+	}
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static void exynos_ufs_config_phy_cap_attr(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G1_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g1_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G2_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g2_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G3_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g3_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G1_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g1_prep_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G2_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g2_prep_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G3_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g3_prep_sync_len_cap);
+	}
+
+	if (attr->rx_adv_fine_gran_sup_en == 0) {
+		for_each_ufs_rx_lane(ufs, i) {
+			ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_ADV_GRANULARITY_CAP, i), 0);
+
+			if (attr->rx_min_actv_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_MIN_ACTIVATETIME_CAP,
+						i), attr->rx_min_actv_time_cap);
+
+			if (attr->rx_hibern8_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_HIBERN8TIME_CAP, i),
+						attr->rx_hibern8_time_cap);
+		}
+	} else if (attr->rx_adv_fine_gran_sup_en == 1) {
+		for_each_ufs_rx_lane(ufs, i) {
+			if (attr->rx_adv_fine_gran_step)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_ADV_GRANULARITY_CAP,
+						i), RX_ADV_FINE_GRAN_STEP(
+						attr->rx_adv_fine_gran_step));
+
+			if (attr->rx_adv_min_actv_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(
+						RX_ADV_MIN_ACTIVATETIME_CAP, i),
+						attr->rx_adv_min_actv_time_cap);
+
+			if (attr->rx_adv_hibern8_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_ADV_HIBERN8TIME_CAP,
+						i),
+						attr->rx_adv_hibern8_time_cap);
+		}
+	}
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static void exynos_ufs_establish_connt(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	enum {
+		DEV_ID		= 0x00,
+		PEER_DEV_ID	= 0x01,
+		PEER_CPORT_ID	= 0x00,
+		TRAFFIC_CLASS	= 0x00,
+	};
+
+	/* allow cport attributes to be set */
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), CPORT_IDLE);
+
+	/* local unipro attributes */
+	ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID), DEV_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID_VALID), TRUE);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERDEVICEID), PEER_DEV_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERCPORTID), PEER_CPORT_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CPORTFLAGS), CPORT_DEF_FLAGS);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_TRAFFICCLASS), TRAFFIC_CLASS);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), CPORT_CONNECTED);
+}
+
+static void exynos_ufs_config_smu(struct exynos_ufs *ufs)
+{
+	u32 reg, val;
+
+	exynos_ufs_disable_auto_ctrl_hcc_save(ufs, &val);
+
+	/* make encryption disabled by default */
+	reg = ufsp_readl(ufs, UFSPRSECURITY);
+	ufsp_writel(ufs, reg | NSSMU, UFSPRSECURITY);
+	ufsp_writel(ufs, 0x0, UFSPSBEGIN0);
+	ufsp_writel(ufs, 0xffffffff, UFSPSEND0);
+	ufsp_writel(ufs, 0xff, UFSPSLUN0);
+	ufsp_writel(ufs, 0xf1, UFSPSCTRL0);
+
+	exynos_ufs_auto_ctrl_hcc_restore(ufs, &val);
+}
+
+static void exynos_ufs_config_sync_pattern_mask(struct exynos_ufs *ufs,
+					struct uic_pwr_mode *pwr)
+{
+	struct ufs_hba *hba = ufs->hba;
+	u8 g = pwr->gear;
+	u32 mask, sync_len;
+	enum {
+		SYNC_LEN_G1 = 80 * 1000, /* 80us */
+		SYNC_LEN_G2 = 40 * 1000, /* 44us */
+		SYNC_LEN_G3 = 20 * 1000, /* 20us */
+	};
+	int i;
+
+	if (g == 1)
+		sync_len = SYNC_LEN_G1;
+	else if (g == 2)
+		sync_len = SYNC_LEN_G2;
+	else if (g == 3)
+		sync_len = SYNC_LEN_G3;
+	else
+		return;
+
+	mask = exynos_ufs_calc_time_cntr(ufs, sync_len);
+	mask = (mask >> 8) & 0xff;
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB_SEL(RX_SYNC_MASK_LENGTH, i), mask);
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static int exynos_ufs_pre_pwr_mode(struct ufs_hba *hba,
+				struct ufs_pa_layer_attr *pwr_max,
+				struct ufs_pa_layer_attr *final)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct uic_pwr_mode *pwr_req = &ufs->pwr_req;
+	struct uic_pwr_mode *pwr_act = &ufs->pwr_act;
+
+	final->gear_rx
+		= pwr_act->gear = min_t(u32, pwr_max->gear_rx, pwr_req->gear);
+	final->gear_tx
+		= pwr_act->gear = min_t(u32, pwr_max->gear_tx, pwr_req->gear);
+	final->lane_rx
+		= pwr_act->lane = min_t(u32, pwr_max->lane_rx, pwr_req->lane);
+	final->lane_tx
+		= pwr_act->lane = min_t(u32, pwr_max->lane_tx, pwr_req->lane);
+	final->pwr_rx = pwr_act->mode = pwr_req->mode;
+	final->pwr_tx = pwr_act->mode = pwr_req->mode;
+	final->hs_rate = pwr_act->hs_series = pwr_req->hs_series;
+
+	/* save and configure l2 timer */
+	pwr_act->l_l2_timer[0] = pwr_req->l_l2_timer[0];
+	pwr_act->l_l2_timer[1] = pwr_req->l_l2_timer[1];
+	pwr_act->l_l2_timer[2] = pwr_req->l_l2_timer[2];
+	pwr_act->r_l2_timer[0] = pwr_req->r_l2_timer[0];
+	pwr_act->r_l2_timer[1] = pwr_req->r_l2_timer[1];
+	pwr_act->r_l2_timer[2] = pwr_req->r_l2_timer[2];
+
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_FC0PROTTIMEOUTVAL), pwr_act->l_l2_timer[0]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_TC0REPLAYTIMEOUTVAL), pwr_act->l_l2_timer[1]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_AFC0REQTIMEOUTVAL), pwr_act->l_l2_timer[2]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA0), pwr_act->r_l2_timer[0]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA1), pwr_act->r_l2_timer[1]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA2), pwr_act->r_l2_timer[2]);
+
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[0], UNIPRO_DME_PWR_REQ_LOCALL2TIMER0);
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[1], UNIPRO_DME_PWR_REQ_LOCALL2TIMER1);
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[2], UNIPRO_DME_PWR_REQ_LOCALL2TIMER2);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[0], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER0);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[1], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER1);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[2], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER2);
+
+	if (ufs->drv_data->pre_pwr_change)
+		ufs->drv_data->pre_pwr_change(ufs, pwr_act);
+
+	if (IS_UFS_PWR_MODE_HS(pwr_act->mode)) {
+		exynos_ufs_config_sync_pattern_mask(ufs, pwr_act);
+
+		switch (pwr_act->hs_series) {
+		case PA_HS_MODE_A:
+		case PA_HS_MODE_B:
+			phy_calibrate(generic_phy);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+#define PWR_MODE_STR_LEN	64
+static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
+				struct ufs_pa_layer_attr *pwr_max,
+				struct ufs_pa_layer_attr *pwr_req)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct uic_pwr_mode *pwr = &ufs->pwr_act;
+	char pwr_str[PWR_MODE_STR_LEN] = "";
+	int ret = 0;
+
+	if (ufs->drv_data->post_pwr_change)
+		ufs->drv_data->post_pwr_change(ufs, pwr);
+
+	if (IS_UFS_PWR_MODE_HS(pwr->mode)) {
+		switch (pwr->hs_series) {
+		case PA_HS_MODE_A:
+		case PA_HS_MODE_B:
+			phy_calibrate(generic_phy);
+			break;
+		}
+
+		snprintf(pwr_str, sizeof(pwr_str), "Fast%s series_%s G_%d L_%d",
+			pwr->mode == FASTAUTO_MODE ? "_Auto" : "",
+			pwr->hs_series == PA_HS_MODE_A ? "A" : "B",
+			pwr->gear, pwr->lane);
+	} else if (IS_UFS_PWR_MODE_PWM(pwr->mode)) {
+		snprintf(pwr_str, sizeof(pwr_str), "Slow%s G_%d L_%d",
+			pwr->mode == SLOWAUTO_MODE ? "_Auto" : "",
+			pwr->gear, pwr->lane);
+	}
+
+	dev_info(hba->dev, "Power mode change %d : %s\n", ret, pwr_str);
+	return ret;
+}
+
+static void exynos_ufs_specify_nexus_t_xfer_req(struct ufs_hba *hba,
+						int tag, bool op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	u32 type;
+
+	type =  hci_readl(ufs, HCI_UTRL_NEXUS_TYPE);
+
+	if (op)
+		hci_writel(ufs, type | (1 << tag), HCI_UTRL_NEXUS_TYPE);
+	else
+		hci_writel(ufs, type & ~(1 << tag), HCI_UTRL_NEXUS_TYPE);
+}
+
+static void exynos_ufs_specify_nexus_t_tm_req(struct ufs_hba *hba,
+						int tag, u8 func)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	u32 type;
+
+	type =  hci_readl(ufs, HCI_UTMRL_NEXUS_TYPE);
+
+	switch (func) {
+	case UFS_ABORT_TASK:
+	case UFS_QUERY_TASK:
+		hci_writel(ufs, type | (1 << tag), HCI_UTMRL_NEXUS_TYPE);
+		break;
+	case UFS_ABORT_TASK_SET:
+	case UFS_CLEAR_TASK_SET:
+	case UFS_LOGICAL_RESET:
+	case UFS_QUERY_TASK_SET:
+		hci_writel(ufs, type & ~(1 << tag), HCI_UTMRL_NEXUS_TYPE);
+		break;
+	}
+}
+
+static void exynos_ufs_phy_init(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct phy *generic_phy = ufs->phy;
+
+	if (ufs->avail_ln_rx == 0 || ufs->avail_ln_tx == 0) {
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_AVAILRXDATALANES),
+			&ufs->avail_ln_rx);
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_AVAILTXDATALANES),
+			&ufs->avail_ln_tx);
+		WARN(ufs->avail_ln_rx != ufs->avail_ln_tx,
+			"available data lane is not equal(rx:%d, tx:%d)\n",
+			ufs->avail_ln_rx, ufs->avail_ln_tx);
+	}
+
+	phy_set_bus_width(generic_phy, ufs->avail_ln_rx);
+	phy_init(generic_phy);
+}
+
+static void exynos_ufs_config_unipro(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_CLK_PERIOD),
+		DIV_ROUND_UP(NSEC_PER_SEC, ufs->mclk_rate));
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TXTRAILINGCLOCKS),
+			ufs->drv_data->uic_attr->tx_trailingclks);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE),
+			ufs->drv_data->uic_attr->pa_dbg_option_suite);
+}
+
+static void exynos_ufs_config_intr(struct exynos_ufs *ufs, u32 errs, u8 index)
+{
+	switch (index) {
+	case UNIPRO_L1_5:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_PA_LAYER);
+		break;
+	case UNIPRO_L2:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_DL_LAYER);
+		break;
+	case UNIPRO_L3:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_N_LAYER);
+		break;
+	case UNIPRO_L4:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_T_LAYER);
+		break;
+	case UNIPRO_DME:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_DME_LAYER);
+		break;
+	}
+}
+
+static int exynos_ufs_pre_link(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	/* hci */
+	exynos_ufs_config_intr(ufs, DFES_DEF_L2_ERRS, UNIPRO_L2);
+	exynos_ufs_config_intr(ufs, DFES_DEF_L3_ERRS, UNIPRO_L3);
+	exynos_ufs_config_intr(ufs, DFES_DEF_L4_ERRS, UNIPRO_L4);
+	exynos_ufs_set_unipro_pclk_div(ufs);
+
+	/* unipro */
+	exynos_ufs_config_unipro(ufs);
+
+	/* m-phy */
+	exynos_ufs_phy_init(ufs);
+	exynos_ufs_config_phy_time_attr(ufs);
+	exynos_ufs_config_phy_cap_attr(ufs);
+
+	if (ufs->drv_data->pre_link)
+		ufs->drv_data->pre_link(ufs);
+
+	return 0;
+}
+
+static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs)
+{
+	const u8 cntr_div = 40;
+	u32 val;
+
+	val = exynos_ufs_calc_time_cntr(ufs, IATOVAL_NSEC / cntr_div);
+	hci_writel(ufs, val & CNT_VAL_1US_MASK, HCI_1US_TO_CNT_VAL);
+}
+
+static int exynos_ufs_post_link(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	exynos_ufs_establish_connt(ufs);
+	exynos_ufs_fit_aggr_timeout(ufs);
+
+	hci_writel(ufs, 0xa, HCI_DATA_REORDER);
+	hci_writel(ufs, PRDT_PREFECT_EN | PRDT_SET_SIZE(12),
+			HCI_TXPRDT_ENTRY_SIZE);
+	hci_writel(ufs, PRDT_SET_SIZE(12), HCI_RXPRDT_ENTRY_SIZE);
+	hci_writel(ufs, (1 << hba->nutrs) - 1, HCI_UTRL_NEXUS_TYPE);
+	hci_writel(ufs, (1 << hba->nutmrs) - 1, HCI_UTMRL_NEXUS_TYPE);
+	hci_writel(ufs, 0xf, HCI_AXIDMA_RWDATA_BURST_LEN);
+
+	if (ufs->opts & EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB(T_DBG_SKIP_INIT_HIBERN8_EXIT), TRUE);
+
+	if (attr->pa_granularity) {
+		exynos_ufs_enable_dbg_mode(hba);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_GRANULARITY),
+				attr->pa_granularity);
+		exynos_ufs_disable_dbg_mode(hba);
+
+		if (attr->pa_tactivate)
+			ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TACTIVATE),
+					attr->pa_tactivate);
+		if (attr->pa_hibern8time &&
+		    !(ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER))
+			ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HIBERN8TIME),
+					attr->pa_hibern8time);
+	}
+
+	if (ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER) {
+		if (!attr->pa_granularity)
+			ufshcd_dme_get(hba, UIC_ARG_MIB(PA_GRANULARITY),
+					&attr->pa_granularity);
+		if (!attr->pa_hibern8time)
+			ufshcd_dme_get(hba, UIC_ARG_MIB(PA_HIBERN8TIME),
+					&attr->pa_hibern8time);
+		/*
+		 * not wait for HIBERN8 time to exit hibernation
+		 */
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HIBERN8TIME), 0);
+
+		if (attr->pa_granularity < 1 || attr->pa_granularity > 6) {
+			/* Valid range for granularity: 1 ~ 6 */
+			dev_warn(hba->dev,
+				"%s: pa_granularty %d is invalid, assuming backwards compatibility\n",
+				__func__,
+				attr->pa_granularity);
+			attr->pa_granularity = 6;
+		}
+	}
+
+	phy_calibrate(generic_phy);
+
+	if (ufs->drv_data->post_link)
+		ufs->drv_data->post_link(ufs);
+
+	return 0;
+}
+
+static void exynos_ufs_specify_pwr_mode(struct device_node *np,
+				struct exynos_ufs *ufs)
+{
+	struct uic_pwr_mode *pwr = &ufs->pwr_req;
+	const char *str = NULL;
+
+	if (!of_property_read_string(np, "ufs,pwr-attr-mode", &str)) {
+		if (!strncmp(str, "FAST", sizeof("FAST")))
+			pwr->mode = FAST_MODE;
+		else if (!strncmp(str, "SLOW", sizeof("SLOW")))
+			pwr->mode = SLOW_MODE;
+		else if (!strncmp(str, "FAST_auto", sizeof("FAST_auto")))
+			pwr->mode = FASTAUTO_MODE;
+		else if (!strncmp(str, "SLOW_auto", sizeof("SLOW_auto")))
+			pwr->mode = SLOWAUTO_MODE;
+		else
+			pwr->mode = FAST_MODE;
+	} else {
+		pwr->mode = FAST_MODE;
+	}
+
+	if (of_property_read_u32(np, "ufs,pwr-attr-lane", &pwr->lane))
+		pwr->lane = 1;
+
+	if (of_property_read_u32(np, "ufs,pwr-attr-gear", &pwr->gear))
+		pwr->gear = 1;
+
+	if (IS_UFS_PWR_MODE_HS(pwr->mode)) {
+		if (!of_property_read_string(np,
+					"ufs,pwr-attr-hs-series", &str)) {
+			if (!strncmp(str, "HS_rate_a", sizeof("HS_rate_a")))
+				pwr->hs_series = PA_HS_MODE_A;
+			else if (!strncmp(str, "HS_rate_b",
+				    sizeof("HS_rate_b")))
+				pwr->hs_series = PA_HS_MODE_B;
+			else
+				pwr->hs_series = PA_HS_MODE_A;
+		} else {
+			pwr->hs_series = PA_HS_MODE_A;
+		}
+	}
+
+	if (of_property_read_u32_array(
+		np, "ufs,pwr-local-l2-timer", pwr->l_l2_timer, 3)) {
+		pwr->l_l2_timer[0] = FC0PROTTIMEOUTVAL;
+		pwr->l_l2_timer[1] = TC0REPLAYTIMEOUTVAL;
+		pwr->l_l2_timer[2] = AFC0REQTIMEOUTVAL;
+	}
+
+	if (of_property_read_u32_array(
+		np, "ufs,pwr-remote-l2-timer", pwr->r_l2_timer, 3)) {
+		pwr->r_l2_timer[0] = FC0PROTTIMEOUTVAL;
+		pwr->r_l2_timer[1] = TC0REPLAYTIMEOUTVAL;
+		pwr->r_l2_timer[2] = AFC0REQTIMEOUTVAL;
+	}
+}
+
+static int exynos_ufs_parse_dt(struct device *dev, struct exynos_ufs *ufs)
+{
+	struct device_node *np = dev->of_node;
+	struct exynos_ufs_drv_data *drv_data = &exynos_ufs_drvs;
+	struct exynos_ufs_uic_attr *attr;
+	u32 freq[2];
+	int ret;
+
+	while (drv_data->compatible) {
+		if (of_device_is_compatible(np, drv_data->compatible)) {
+			ufs->drv_data = drv_data;
+			break;
+		}
+		drv_data++;
+	}
+
+	if (ufs->drv_data && ufs->drv_data->uic_attr) {
+		attr = ufs->drv_data->uic_attr;
+	} else {
+		dev_err(dev, "failed to get uic attributes\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = of_property_read_u32_array(np,
+			"pclk-freq-avail-range", freq, ARRAY_SIZE(freq));
+	if (!ret) {
+		ufs->pclk_avail_min = freq[0];
+		ufs->pclk_avail_max = freq[1];
+	} else {
+		dev_err(dev, "failed to get available pclk range\n");
+		goto out;
+	}
+
+	exynos_ufs_specify_pwr_mode(np, ufs);
+
+	if (!of_property_read_u32(np, "ufs-rx-adv-fine-gran-sup_en",
+				&attr->rx_adv_fine_gran_sup_en)) {
+		if (attr->rx_adv_fine_gran_sup_en == 0) {
+			/* 100us step */
+			if (of_property_read_u32(np,
+					"ufs-rx-min-activate-time-cap",
+					&attr->rx_min_actv_time_cap))
+				dev_warn(dev,
+					"ufs-rx-min-activate-time-cap is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-hibern8-time-cap",
+					&attr->rx_hibern8_time_cap))
+				dev_warn(dev,
+					"ufs-rx-hibern8-time-cap is empty\n");
+		} else if (attr->rx_adv_fine_gran_sup_en == 1) {
+			/* fine granularity step */
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-fine-gran-step",
+					&attr->rx_adv_fine_gran_step))
+				dev_warn(dev,
+					"ufs-rx-adv-fine-gran-step is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-min-activate-time-cap",
+					&attr->rx_adv_min_actv_time_cap))
+				dev_warn(dev,
+					"ufs-rx-adv-min-activate-time-cap is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-hibern8-time-cap",
+					&attr->rx_adv_hibern8_time_cap))
+				dev_warn(dev,
+					"ufs-rx-adv-hibern8-time-cap is empty\n");
+		} else {
+			dev_warn(dev,
+				"not supported val for ufs-rx-adv-fine-gran-sup_en %d\n",
+				attr->rx_adv_fine_gran_sup_en);
+		}
+	} else {
+		attr->rx_adv_fine_gran_sup_en = 0xf;
+	}
+
+	if (!of_property_read_u32(np,
+				"ufs-pa-granularity", &attr->pa_granularity)) {
+		if (of_property_read_u32(np,
+				"ufs-pa-tacctivate", &attr->pa_tactivate))
+			dev_warn(dev, "ufs-pa-tacctivate is empty\n");
+
+		if (of_property_read_u32(np,
+				"ufs-pa-hibern8time", &attr->pa_hibern8time))
+			dev_warn(dev, "ufs-pa-hibern8time is empty\n");
+	}
+
+out:
+	return ret;
+}
+
+static int exynos_ufs_init(struct ufs_hba *hba)
+{
+	struct device *dev = hba->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct exynos_ufs *ufs;
+	struct resource *res;
+	int ret;
+
+	ufs = devm_kzalloc(dev, sizeof(*ufs), GFP_KERNEL);
+	if (!ufs)
+		return -ENOMEM;
+
+	/* exynos-specific hci */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "vs_hci");
+	ufs->reg_hci = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_hci) {
+		dev_err(dev, "cannot ioremap for hci vendor register\n");
+		return -ENOMEM;
+	}
+
+	/* unipro */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "unipro");
+	ufs->reg_unipro = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_unipro) {
+		dev_err(dev, "cannot ioremap for unipro register\n");
+		return -ENOMEM;
+	}
+
+	/* ufs protector */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ufsp");
+	ufs->reg_ufsp = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_ufsp) {
+		dev_err(dev, "cannot ioremap for ufs protector register\n");
+		return -ENOMEM;
+	}
+
+	ret = exynos_ufs_parse_dt(dev, ufs);
+	if (ret) {
+		dev_err(dev, "failed to get dt info.\n");
+		goto out;
+	}
+
+	ufs->phy = devm_phy_get(dev, "ufs-phy");
+	if (IS_ERR(ufs->phy)) {
+		ret = PTR_ERR(ufs->phy);
+		dev_err(dev, "failed to get ufs-phy\n");
+		goto out;
+	}
+
+	ret = phy_power_on(ufs->phy);
+	if (ret)
+		goto phy_exit;
+
+	ufs->hba = hba;
+	ufs->opts = ufs->drv_data->opts |
+		EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB |
+		EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER;
+	ufs->rx_sel_idx = PA_MAXDATALANES;
+	if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX)
+		ufs->rx_sel_idx = 0;
+	hba->priv = (void *)ufs;
+	hba->quirks = ufs->drv_data->quirks;
+	if (ufs->drv_data->drv_init) {
+		ret = ufs->drv_data->drv_init(dev, ufs);
+		if (ret) {
+			dev_err(dev, "failed to init drv-data\n");
+			goto phy_off;
+		}
+	}
+
+	ret = exynos_ufs_get_clk_info(ufs);
+	if (ret)
+		goto phy_off;
+	exynos_ufs_specify_phy_time_attr(ufs);
+	exynos_ufs_config_smu(ufs);
+	return 0;
+
+phy_off:
+	phy_power_off(ufs->phy);
+phy_exit:
+	phy_exit(ufs->phy);
+	hba->priv = NULL;
+out:
+	return ret;
+}
+
+static int exynos_ufs_host_reset(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	unsigned long timeout = jiffies + msecs_to_jiffies(1);
+	u32 val;
+	int ret = 0;
+
+	exynos_ufs_disable_auto_ctrl_hcc_save(ufs, &val);
+
+	hci_writel(ufs, UFS_SW_RST_MASK, HCI_SW_RST);
+
+	do {
+		if (!(hci_readl(ufs, HCI_SW_RST) & UFS_SW_RST_MASK))
+			goto out;
+	} while (time_before(jiffies, timeout));
+
+	dev_err(hba->dev, "timeout host sw-reset\n");
+	ret = -ETIMEDOUT;
+
+out:
+	exynos_ufs_auto_ctrl_hcc_restore(ufs, &val);
+	return ret;
+}
+
+static void exynos_ufs_dev_hw_reset(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	hci_writel(ufs, 0 << 0, HCI_GPIO_OUT);
+	udelay(5);
+	hci_writel(ufs, 1 << 0, HCI_GPIO_OUT);
+}
+
+static void exynos_ufs_pre_hibern8(struct ufs_hba *hba, u8 enter)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	if (!enter) {
+		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
+			exynos_ufs_disable_auto_ctrl_hcc(ufs);
+		exynos_ufs_ungate_clks(ufs);
+
+		if (ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER) {
+			const unsigned int granularity_tbl[] = {
+				1, 4, 8, 16, 32, 100
+			};
+			int h8_time = attr->pa_hibern8time *
+				granularity_tbl[attr->pa_granularity - 1];
+			unsigned long us;
+			s64 delta;
+
+			do {
+				delta = h8_time - ktime_us_delta(ktime_get(),
+							ufs->entry_hibern8_t);
+				if (delta <= 0)
+					break;
+
+				us = min_t(s64, delta, USEC_PER_MSEC);
+				if (us >= 10)
+					usleep_range(us, us + 10);
+			} while (1);
+		}
+	}
+}
+
+static void exynos_ufs_post_hibern8(struct ufs_hba *hba, u8 enter)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!enter) {
+		struct uic_pwr_mode *pwr = &ufs->pwr_act;
+		u32 mode = 0;
+
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_PWRMODE), &mode);
+		if (mode != (pwr->mode << 4 | pwr->mode)) {
+			dev_warn(hba->dev, "%s: power mode change\n", __func__);
+			hba->pwr_info.pwr_rx = (mode >> 4) & 0xf;
+			hba->pwr_info.pwr_tx = mode & 0xf;
+			ufshcd_config_pwr_mode(hba, &hba->max_pwr_info.info);
+		}
+
+		if (!(ufs->opts & EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB))
+			exynos_ufs_establish_connt(ufs);
+	} else {
+		ufs->entry_hibern8_t = ktime_get();
+		exynos_ufs_gate_clks(ufs);
+		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
+			exynos_ufs_enable_auto_ctrl_hcc(ufs);
+	}
+}
+
+static int exynos_ufs_hce_enable_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_host_reset(hba);
+		if (ret)
+			return ret;
+		exynos_ufs_dev_hw_reset(hba);
+		break;
+	case POST_CHANGE:
+		exynos_ufs_calc_pwm_clk_div(ufs);
+		if (!(ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL))
+			exynos_ufs_enable_auto_ctrl_hcc(ufs);
+		break;
+	}
+
+	return ret;
+}
+
+static int exynos_ufs_link_startup_notify(struct ufs_hba *hba,
+					  enum ufs_notify_change_status status)
+{
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_pre_link(hba);
+		break;
+	case POST_CHANGE:
+		ret = exynos_ufs_post_link(hba);
+		break;
+	}
+
+	return ret;
+}
+
+static int exynos_ufs_pwr_change_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status,
+					struct ufs_pa_layer_attr *pwr_max,
+					struct ufs_pa_layer_attr *pwr_req)
+{
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_pre_pwr_mode(hba, pwr_max, pwr_req);
+		break;
+	case POST_CHANGE:
+		ret = exynos_ufs_post_pwr_mode(hba, NULL, pwr_req);
+		break;
+	}
+
+	return ret;
+}
+
+static void exynos_ufs_hibern8_notify(struct ufs_hba *hba,
+				     enum uic_cmd_dme enter,
+				     enum ufs_notify_change_status notify)
+{
+	switch ((u8)notify) {
+	case PRE_CHANGE:
+		exynos_ufs_pre_hibern8(hba, enter);
+		break;
+	case POST_CHANGE:
+		exynos_ufs_post_hibern8(hba, enter);
+		break;
+	}
+}
+
+static int exynos_ufs_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!ufshcd_is_link_active(hba))
+		phy_power_off(ufs->phy);
+
+	return 0;
+}
+
+static int exynos_ufs_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!ufshcd_is_link_active(hba))
+		phy_power_on(ufs->phy);
+
+	exynos_ufs_config_smu(ufs);
+
+	return 0;
+}
+
+static struct ufs_hba_variant_ops ufs_hba_exynos_ops = {
+	.name				= "exynos_ufs",
+	.init				= exynos_ufs_init,
+	.hce_enable_notify		= exynos_ufs_hce_enable_notify,
+	.link_startup_notify		= exynos_ufs_link_startup_notify,
+	.pwr_change_notify		= exynos_ufs_pwr_change_notify,
+	.setup_xfer_req			= exynos_ufs_specify_nexus_t_xfer_req,
+	.setup_task_mgmt		= exynos_ufs_specify_nexus_t_tm_req,
+	.hibern8_notify			= exynos_ufs_hibern8_notify,
+	.suspend			= exynos_ufs_suspend,
+	.resume				= exynos_ufs_resume,
+};
+
+static int exynos_ufs_probe(struct platform_device *pdev)
+{
+	int err;
+	struct device *dev = &pdev->dev;
+
+	err = ufshcd_pltfrm_init(pdev, &ufs_hba_exynos_ops);
+	if (err)
+		dev_err(dev, "ufshcd_pltfrm_init() failed %d\n", err);
+
+	return err;
+}
+
+static int exynos_ufs_remove(struct platform_device *pdev)
+{
+	struct ufs_hba *hba =  platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&(pdev)->dev);
+	ufshcd_remove(hba);
+	return 0;
+}
+
+struct exynos_ufs_drv_data exynos_ufs_drvs = {
+
+	.compatible		= "samsung,exynos7-ufs",
+	.uic_attr		= &exynos7_uic_attr,
+	.quirks			= UFSHCD_QUIRK_PRDT_BYTE_GRAN |
+				  UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
+				  UFSHCI_QUIRK_BROKEN_HCE |
+				  UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
+	.opts			= EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
+				  EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
+				  EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
+	.drv_init		= exynos7_ufs_drv_init,
+	.pre_link		= exynos7_ufs_pre_link,
+	.post_link		= exynos7_ufs_post_link,
+	.pre_pwr_change		= exynos7_ufs_pre_pwr_change,
+	.post_pwr_change	= exynos7_ufs_post_pwr_change,
+};
+
+static const struct of_device_id exynos_ufs_of_match[] = {
+	{ .compatible = "samsung,exynos7-ufs",
+	  .data	      = &exynos_ufs_drvs },
+	{},
+};
+
+static const struct dev_pm_ops exynos_ufs_pm_ops = {
+	.suspend	= ufshcd_pltfrm_suspend,
+	.resume		= ufshcd_pltfrm_resume,
+	.runtime_suspend = ufshcd_pltfrm_runtime_suspend,
+	.runtime_resume  = ufshcd_pltfrm_runtime_resume,
+	.runtime_idle    = ufshcd_pltfrm_runtime_idle,
+};
+
+static struct platform_driver exynos_ufs_pltform = {
+	.probe	= exynos_ufs_probe,
+	.remove	= exynos_ufs_remove,
+	.shutdown = ufshcd_pltfrm_shutdown,
+	.driver	= {
+		.name	= "exynos-ufshc",
+		.pm	= &exynos_ufs_pm_ops,
+		.of_match_table = of_match_ptr(exynos_ufs_of_match),
+	},
+};
+module_platform_driver(exynos_ufs_pltform);
diff --git a/drivers/scsi/ufs/ufs-exynos.h b/drivers/scsi/ufs/ufs-exynos.h
new file mode 100644
index 000000000000..98efffc2c19a
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-exynos.h
@@ -0,0 +1,268 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS Host Controller driver for Exynos specific extensions
+ *
+ * Copyright (C) 2014-2015 Samsung Electronics Co., Ltd.
+ *
+ */
+
+#ifndef _UFS_EXYNOS_H_
+#define _UFS_EXYNOS_H_
+
+/*
+ * UNIPRO registers
+ */
+#define UNIPRO_DBG_FORCE_DME_CTRL_STATE		0x150
+
+/*
+ * MIBs for PA debug registers
+ */
+#define PA_DBG_CLK_PERIOD	0x9514
+#define PA_DBG_TXPHY_CFGUPDT	0x9518
+#define PA_DBG_RXPHY_CFGUPDT	0x9519
+#define PA_DBG_MODE		0x9529
+#define PA_DBG_SKIP_RESET_PHY	0x9539
+#define PA_DBG_OV_TM		0x9540
+#define PA_DBG_SKIP_LINE_RESET	0x9541
+#define PA_DBG_LINE_RESET_REQ	0x9543
+#define PA_DBG_OPTION_SUITE	0x9564
+#define PA_DBG_OPTION_SUITE_DYN	0x9565
+
+/*
+ * MIBs for Transport Layer debug registers
+ */
+#define T_DBG_SKIP_INIT_HIBERN8_EXIT	0xc001
+
+/*
+ * Exynos MPHY attributes
+ */
+#define TX_LINERESET_N_VAL	0x0277
+#define TX_LINERESET_N(v)	(((v) >> 10) & 0xFF)
+#define TX_LINERESET_P_VAL	0x027D
+#define TX_LINERESET_P(v)	(((v) >> 12) & 0xFF)
+#define TX_OV_SLEEP_CNT_TIMER	0x028E
+#define TX_OV_H8_ENTER_EN	(1 << 7)
+#define TX_OV_SLEEP_CNT(v)	(((v) >> 5) & 0x7F)
+#define TX_HIGH_Z_CNT_11_08	0x028C
+#define TX_HIGH_Z_CNT_H(v)	(((v) >> 8) & 0xF)
+#define TX_HIGH_Z_CNT_07_00	0x028D
+#define TX_HIGH_Z_CNT_L(v)	((v) & 0xFF)
+#define TX_BASE_NVAL_07_00	0x0293
+#define TX_BASE_NVAL_L(v)	((v) & 0xFF)
+#define TX_BASE_NVAL_15_08	0x0294
+#define TX_BASE_NVAL_H(v)	(((v) >> 8) & 0xFF)
+#define TX_GRAN_NVAL_07_00	0x0295
+#define TX_GRAN_NVAL_L(v)	((v) & 0xFF)
+#define TX_GRAN_NVAL_10_08	0x0296
+#define TX_GRAN_NVAL_H(v)	(((v) >> 8) & 0x3)
+
+#define RX_FILLER_ENABLE	0x0316
+#define RX_FILLER_EN		(1 << 1)
+#define RX_LINERESET_VAL	0x0317
+#define RX_LINERESET(v)	(((v) >> 12) & 0xFF)
+#define RX_LCC_IGNORE		0x0318
+#define RX_SYNC_MASK_LENGTH	0x0321
+#define RX_HIBERN8_WAIT_VAL_BIT_20_16	0x0331
+#define RX_HIBERN8_WAIT_VAL_BIT_15_08	0x0332
+#define RX_HIBERN8_WAIT_VAL_BIT_07_00	0x0333
+#define RX_OV_SLEEP_CNT_TIMER	0x0340
+#define RX_OV_SLEEP_CNT(v)	(((v) >> 6) & 0x1F)
+#define RX_OV_STALL_CNT_TIMER	0x0341
+#define RX_OV_STALL_CNT(v)	(((v) >> 4) & 0xFF)
+#define RX_BASE_NVAL_07_00	0x0355
+#define RX_BASE_NVAL_L(v)	((v) & 0xFF)
+#define RX_BASE_NVAL_15_08	0x0354
+#define RX_BASE_NVAL_H(v)	(((v) >> 8) & 0xFF)
+#define RX_GRAN_NVAL_07_00	0x0353
+#define RX_GRAN_NVAL_L(v)	((v) & 0xFF)
+#define RX_GRAN_NVAL_10_08	0x0352
+#define RX_GRAN_NVAL_H(v)	(((v) >> 8) & 0x3)
+
+#define CMN_PWM_CLK_CTRL	0x0402
+#define PWM_CLK_CTRL_MASK	0x3
+
+#define IATOVAL_NSEC		20000	/* unit: ns */
+#define UNIPRO_PCLK_PERIOD(ufs) (NSEC_PER_SEC / ufs->pclk_rate)
+
+struct exynos_ufs;
+
+struct uic_pwr_mode {
+	u32 lane;
+	u32 gear;
+	u8 mode;
+	u8 hs_series;
+	u32 l_l2_timer[3];	/* local */
+	u32 r_l2_timer[3];	/* remote */
+};
+
+struct exynos_ufs_uic_attr {
+	/* TX Attributes */
+	unsigned int tx_trailingclks;
+	unsigned int tx_dif_p_nsec;
+	unsigned int tx_dif_n_nsec;
+	unsigned int tx_high_z_cnt_nsec;
+	unsigned int tx_base_unit_nsec;
+	unsigned int tx_gran_unit_nsec;
+	unsigned int tx_sleep_cnt;
+	unsigned int tx_min_activatetime;
+	/* RX Attributes */
+	unsigned int rx_filler_enable;
+	unsigned int rx_dif_p_nsec;
+	unsigned int rx_hibern8_wait_nsec;
+	unsigned int rx_base_unit_nsec;
+	unsigned int rx_gran_unit_nsec;
+	unsigned int rx_sleep_cnt;
+	unsigned int rx_stall_cnt;
+	unsigned int rx_hs_g1_sync_len_cap;
+	unsigned int rx_hs_g2_sync_len_cap;
+	unsigned int rx_hs_g3_sync_len_cap;
+	unsigned int rx_hs_g1_prep_sync_len_cap;
+	unsigned int rx_hs_g2_prep_sync_len_cap;
+	unsigned int rx_hs_g3_prep_sync_len_cap;
+	/* Common Attributes */
+	unsigned int cmn_pwm_clk_ctrl;
+	/* Internal Attributes */
+	unsigned int pa_dbg_option_suite;
+	/* Changeable Attributes */
+	unsigned int rx_adv_fine_gran_sup_en;
+	unsigned int rx_adv_fine_gran_step;
+	unsigned int rx_min_actv_time_cap;
+	unsigned int rx_hibern8_time_cap;
+	unsigned int rx_adv_min_actv_time_cap;
+	unsigned int rx_adv_hibern8_time_cap;
+	unsigned int pa_granularity;
+	unsigned int pa_tactivate;
+	unsigned int pa_hibern8time;
+};
+
+struct exynos_ufs_drv_data {
+	char *compatible;
+	struct exynos_ufs_uic_attr *uic_attr;
+	unsigned int quirks;
+	unsigned int opts;
+	/* SoC's specific operations */
+	int (*drv_init)(struct device *dev, struct exynos_ufs *ufs);
+	int (*pre_link)(struct exynos_ufs *ufs);
+	int (*post_link)(struct exynos_ufs *ufs);
+	int (*pre_pwr_change)(struct exynos_ufs *ufs, struct uic_pwr_mode *pwr);
+	int (*post_pwr_change)(struct exynos_ufs *ufs,
+				struct uic_pwr_mode *pwr);
+};
+
+struct ufs_phy_time_cfg {
+	u32 tx_linereset_p;
+	u32 tx_linereset_n;
+	u32 tx_high_z_cnt;
+	u32 tx_base_n_val;
+	u32 tx_gran_n_val;
+	u32 tx_sleep_cnt;
+	u32 rx_linereset;
+	u32 rx_hibern8_wait;
+	u32 rx_base_n_val;
+	u32 rx_gran_n_val;
+	u32 rx_sleep_cnt;
+	u32 rx_stall_cnt;
+};
+
+struct exynos_ufs {
+	struct ufs_hba *hba;
+	struct phy *phy;
+	void __iomem *reg_hci;
+	void __iomem *reg_unipro;
+	void __iomem *reg_ufsp;
+	struct clk *clk_hci_core;
+	struct clk *clk_unipro_main;
+	struct clk *clk_apb;
+	u32 pclk_rate;
+	u32 pclk_div;
+	u32 pclk_avail_min;
+	u32 pclk_avail_max;
+	u32 mclk_rate;
+	int avail_ln_rx;
+	int avail_ln_tx;
+	int rx_sel_idx;
+	struct uic_pwr_mode pwr_req;	/* requested power mode */
+	struct uic_pwr_mode pwr_act;	/* actual power mode */
+	struct ufs_phy_time_cfg t_cfg;
+	ktime_t entry_hibern8_t;
+	struct exynos_ufs_drv_data *drv_data;
+
+	u32 opts;
+#define EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL		BIT(0)
+#define EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB	BIT(1)
+#define EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL	BIT(2)
+#define EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX	BIT(3)
+#define EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER	BIT(4)
+};
+
+#define for_each_ufs_rx_lane(ufs, i) \
+	for (i = (ufs)->rx_sel_idx; \
+		i < (ufs)->rx_sel_idx + (ufs)->avail_ln_rx; i++)
+#define for_each_ufs_tx_lane(ufs, i) \
+	for (i = 0; i < (ufs)->avail_ln_tx; i++)
+
+#define EXYNOS_UFS_MMIO_FUNC(name)					  \
+static inline void name##_writel(struct exynos_ufs *ufs, u32 val, u32 reg)\
+{									  \
+	writel(val, ufs->reg_##name + reg);				  \
+}									  \
+									  \
+static inline u32 name##_readl(struct exynos_ufs *ufs, u32 reg)		  \
+{									  \
+	return readl(ufs->reg_##name + reg);				  \
+}
+
+EXYNOS_UFS_MMIO_FUNC(hci);
+EXYNOS_UFS_MMIO_FUNC(unipro);
+EXYNOS_UFS_MMIO_FUNC(ufsp);
+#undef EXYNOS_UFS_MMIO_FUNC
+
+extern long exynos_ufs_calc_time_cntr(struct exynos_ufs *, long);
+
+static inline void exynos_ufs_enable_ov_tm(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OV_TM), TRUE);
+}
+
+static inline void exynos_ufs_disable_ov_tm(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OV_TM), FALSE);
+}
+
+static inline void exynos_ufs_enable_dbg_mode(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_MODE), TRUE);
+}
+
+static inline void exynos_ufs_disable_dbg_mode(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_MODE), FALSE);
+}
+
+struct exynos_ufs_drv_data exynos_ufs_drvs;
+
+struct exynos_ufs_uic_attr exynos7_uic_attr = {
+	.tx_trailingclks		= 0x10,
+	.tx_dif_p_nsec			= 3000000,	/* unit: ns */
+	.tx_dif_n_nsec			= 1000000,	/* unit: ns */
+	.tx_high_z_cnt_nsec		= 20000,	/* unit: ns */
+	.tx_base_unit_nsec		= 100000,	/* unit: ns */
+	.tx_gran_unit_nsec		= 4000,		/* unit: ns */
+	.tx_sleep_cnt			= 1000,		/* unit: ns */
+	.tx_min_activatetime		= 0xa,
+	.rx_filler_enable		= 0x2,
+	.rx_dif_p_nsec			= 1000000,	/* unit: ns */
+	.rx_hibern8_wait_nsec		= 4000000,	/* unit: ns */
+	.rx_base_unit_nsec		= 100000,	/* unit: ns */
+	.rx_gran_unit_nsec		= 4000,		/* unit: ns */
+	.rx_sleep_cnt			= 1280,		/* unit: ns */
+	.rx_stall_cnt			= 320,		/* unit: ns */
+	.rx_hs_g1_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g2_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g3_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g1_prep_sync_len_cap	= PREP_LEN(0xf),
+	.rx_hs_g2_prep_sync_len_cap	= PREP_LEN(0xf),
+	.rx_hs_g3_prep_sync_len_cap	= PREP_LEN(0xf),
+	.pa_dbg_option_suite		= 0x30103,
+};
+#endif /* _UFS_EXYNOS_H_ */
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
index 3dc4d8b76509..f441ab54829c 100644
--- a/drivers/scsi/ufs/unipro.h
+++ b/drivers/scsi/ufs/unipro.h
@@ -64,8 +64,25 @@
 #define CFGRXOVR4				0x00E9
 #define RXSQCTRL				0x00B5
 #define CFGRXOVR6				0x00BF
+#define RX_HS_G1_SYNC_LENGTH_CAP		0x008B
+#define RX_HS_G1_PREP_LENGTH_CAP		0x008C
+#define RX_HS_G2_SYNC_LENGTH_CAP		0x0094
+#define RX_HS_G3_SYNC_LENGTH_CAP		0x0095
+#define RX_HS_G2_PREP_LENGTH_CAP		0x0096
+#define RX_HS_G3_PREP_LENGTH_CAP		0x0097
+#define RX_ADV_GRANULARITY_CAP			0x0098
+#define RX_MIN_ACTIVATETIME_CAP			0x008F
+#define RX_HIBERN8TIME_CAP			0x0092
+#define RX_ADV_HIBERN8TIME_CAP			0x0099
+#define RX_ADV_MIN_ACTIVATETIME_CAP		0x009A
+
 
 #define is_mphy_tx_attr(attr)			(attr < RX_MODE)
+#define RX_ADV_FINE_GRAN_STEP(x)		((((x) & 0x3) << 1) | 0x1)
+#define SYNC_LEN_FINE(x)			((x) & 0x3F)
+#define SYNC_LEN_COARSE(x)			((1 << 6) | ((x) & 0x3F))
+#define PREP_LEN(x)				((x) & 0xF)
+
 #define RX_MIN_ACTIVATETIME_UNIT_US		100
 #define HIBERN8TIME_UNIT_US			100
 
@@ -124,6 +141,7 @@
 #define PA_PACPREQEOBTIMEOUT	0x1591
 #define PA_HIBERN8TIME		0x15A7
 #define PA_LOCALVERINFO		0x15A9
+#define PA_GRANULARITY		0x15AA
 #define PA_TACTIVATE		0x15A8
 #define PA_PACPFRAMECOUNT	0x15C0
 #define PA_PACPERRORCOUNT	0x15C1
@@ -181,6 +199,9 @@ enum {
 	UNCHANGED	= 7,
 };
 
+#define IS_UFS_PWR_MODE_HS(m)	(((m) == FAST_MODE) || ((m) == FASTAUTO_MODE))
+#define IS_UFS_PWR_MODE_PWM(m)	(((m) == SLOW_MODE) || ((m) == SLOWAUTO_MODE))
+
 /* PA TX/RX Frequency Series */
 enum {
 	PA_HS_MODE_A	= 1,
@@ -242,6 +263,11 @@ enum ufs_unipro_ver {
 #define DL_PEERTC1PRESENT	0x2066
 #define DL_PEERTC1RXINITCREVAL	0x2067
 
+/* Default value of L2 Timer */
+#define FC0PROTTIMEOUTVAL	8191
+#define TC0REPLAYTIMEOUTVAL	65535
+#define AFC0REQTIMEOUTVAL	32767
+
 /*
  * Network Layer Attributes
  */
@@ -284,4 +310,19 @@ enum {
 	TRUE,
 };
 
+/* CPort setting */
+#define E2EFC_ON	(1 << 0)
+#define E2EFC_OFF	(0 << 0)
+#define CSD_N_ON	(0 << 1)
+#define CSD_N_OFF	(1 << 1)
+#define CSV_N_ON	(0 << 2)
+#define CSV_N_OFF	(1 << 2)
+#define CPORT_DEF_FLAGS	(CSV_N_OFF | CSD_N_OFF | E2EFC_OFF)
+
+/* CPort connection state */
+enum {
+	CPORT_IDLE = 0,
+	CPORT_CONNECTED,
+};
+
 #endif /* _UNIPRO_H_ */
-- 
2.17.1

[PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Alim Akhtar]

This patch introduces Exynos UFS host controller driver,
which mainly handles vendor-specific operations including
link startup, power mode change and hibernation/unhibernation.

Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
[robot: drivers/scsi/ufs/ufs-exynos.c:931:8-10:
 WARNING: possible condition with no effect (if == else)
]
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 drivers/scsi/ufs/Kconfig      |   12 +
 drivers/scsi/ufs/Makefile     |    1 +
 drivers/scsi/ufs/ufs-exynos.c | 1399 +++++++++++++++++++++++++++++++++
 drivers/scsi/ufs/ufs-exynos.h |  268 +++++++
 drivers/scsi/ufs/unipro.h     |   41 +
 5 files changed, 1721 insertions(+)
 create mode 100644 drivers/scsi/ufs/ufs-exynos.c
 create mode 100644 drivers/scsi/ufs/ufs-exynos.h

diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig
index d14c2243e02a..8fda908bce5b 100644
--- a/drivers/scsi/ufs/Kconfig
+++ b/drivers/scsi/ufs/Kconfig
@@ -160,3 +160,15 @@ config SCSI_UFS_BSG
 
 	  Select this if you need a bsg device node for your UFS controller.
 	  If unsure, say N.
+
+config SCSI_UFS_EXYNOS
+	bool "EXYNOS specific hooks to UFS controller platform driver"
+	depends on SCSI_UFSHCD_PLATFORM && ARCH_EXYNOS || COMPILE_TEST
+	select PHY_EXYNOS_UFS
+	help
+	  This selects the EXYNOS specific additions to UFSHCD platform driver.
+	  UFS host on EXYNOS includes HCI and UNIPRO layer, and associates with
+	  UFS-PHY driver.
+
+	  Select this if you have UFS host controller on EXYNOS chipset.
+	  If unsure, say N.
diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile
index 94c6c5d7334b..f0c5b95ec9cc 100644
--- a/drivers/scsi/ufs/Makefile
+++ b/drivers/scsi/ufs/Makefile
@@ -4,6 +4,7 @@ obj-$(CONFIG_SCSI_UFS_DWC_TC_PCI) += tc-dwc-g210-pci.o ufshcd-dwc.o tc-dwc-g210.
 obj-$(CONFIG_SCSI_UFS_DWC_TC_PLATFORM) += tc-dwc-g210-pltfrm.o ufshcd-dwc.o tc-dwc-g210.o
 obj-$(CONFIG_SCSI_UFS_CDNS_PLATFORM) += cdns-pltfrm.o
 obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o
+obj-$(CONFIG_SCSI_UFS_EXYNOS) += ufs-exynos.o
 obj-$(CONFIG_SCSI_UFSHCD) += ufshcd-core.o
 ufshcd-core-y				+= ufshcd.o ufs-sysfs.o
 ufshcd-core-$(CONFIG_SCSI_UFS_BSG)	+= ufs_bsg.o
diff --git a/drivers/scsi/ufs/ufs-exynos.c b/drivers/scsi/ufs/ufs-exynos.c
new file mode 100644
index 000000000000..fe8f67220768
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-exynos.c
@@ -0,0 +1,1399 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * UFS Host Controller driver for Exynos specific extensions
+ *
+ * Copyright (C) 2014-2015 Samsung Electronics Co., Ltd.
+ * Author: Seungwon Jeon  <essuuj@gmail.com>
+ * Author: Alim Akhtar <alim.akhtar@samsung.com>
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy-samsung-ufs.h>
+#include <linux/platform_device.h>
+
+#include "ufshcd.h"
+#include "ufshcd-pltfrm.h"
+#include "ufshci.h"
+#include "unipro.h"
+
+#include "ufs-exynos.h"
+
+/*
+ * Exynos's Vendor specific registers for UFSHCI
+ */
+#define HCI_TXPRDT_ENTRY_SIZE	0x00
+#define PRDT_PREFECT_EN		BIT(31)
+#define PRDT_SET_SIZE(x)	((x) & 0x1F)
+#define HCI_RXPRDT_ENTRY_SIZE	0x04
+#define HCI_1US_TO_CNT_VAL	0x0C
+#define CNT_VAL_1US_MASK	0x3FF
+#define HCI_UTRL_NEXUS_TYPE	0x40
+#define HCI_UTMRL_NEXUS_TYPE	0x44
+#define HCI_SW_RST		0x50
+#define UFS_LINK_SW_RST		BIT(0)
+#define UFS_UNIPRO_SW_RST	BIT(1)
+#define UFS_SW_RST_MASK		(UFS_UNIPRO_SW_RST | UFS_LINK_SW_RST)
+#define HCI_DATA_REORDER	0x60
+#define HCI_UNIPRO_APB_CLK_CTRL	0x68
+#define UNIPRO_APB_CLK(v, x)	(((v) & ~0xF) | ((x) & 0xF))
+#define HCI_AXIDMA_RWDATA_BURST_LEN	0x6C
+#define HCI_GPIO_OUT		0x70
+#define HCI_ERR_EN_PA_LAYER	0x78
+#define HCI_ERR_EN_DL_LAYER	0x7C
+#define HCI_ERR_EN_N_LAYER	0x80
+#define HCI_ERR_EN_T_LAYER	0x84
+#define HCI_ERR_EN_DME_LAYER	0x88
+#define HCI_CLKSTOP_CTRL	0xB0
+#define REFCLK_STOP		BIT(2)
+#define UNIPRO_MCLK_STOP	BIT(1)
+#define UNIPRO_PCLK_STOP	BIT(0)
+#define CLK_STOP_MASK		(REFCLK_STOP |\
+				 UNIPRO_MCLK_STOP |\
+				 UNIPRO_PCLK_STOP)
+#define HCI_MISC		0xB4
+#define REFCLK_CTRL_EN		BIT(7)
+#define UNIPRO_PCLK_CTRL_EN	BIT(6)
+#define UNIPRO_MCLK_CTRL_EN	BIT(5)
+#define HCI_CORECLK_CTRL_EN	BIT(4)
+#define CLK_CTRL_EN_MASK	(REFCLK_CTRL_EN |\
+				 UNIPRO_PCLK_CTRL_EN |\
+				 UNIPRO_MCLK_CTRL_EN)
+/* Device fatal error */
+#define DFES_ERR_EN		BIT(31)
+#define DFES_DEF_L2_ERRS	(UIC_DATA_LINK_LAYER_ERROR_RX_BUF_OF |\
+				 UIC_DATA_LINK_LAYER_ERROR_PA_INIT)
+#define DFES_DEF_L3_ERRS	(UIC_NETWORK_UNSUPPORTED_HEADER_TYPE |\
+				 UIC_NETWORK_BAD_DEVICEID_ENC |\
+				 UIC_NETWORK_LHDR_TRAP_PACKET_DROPPING)
+#define DFES_DEF_L4_ERRS	(UIC_TRANSPORT_UNSUPPORTED_HEADER_TYPE |\
+				 UIC_TRANSPORT_UNKNOWN_CPORTID |\
+				 UIC_TRANSPORT_NO_CONNECTION_RX |\
+				 UIC_TRANSPORT_BAD_TC)
+
+enum {
+	UNIPRO_L1_5 = 0,/* PHY Adapter */
+	UNIPRO_L2,	/* Data Link */
+	UNIPRO_L3,	/* Network */
+	UNIPRO_L4,	/* Transport */
+	UNIPRO_DME,	/* DME */
+};
+
+/*
+ * UNIPRO registers
+ */
+#define UNIPRO_COMP_VERSION			0x000
+#define UNIPRO_DME_PWR_REQ			0x090
+#define UNIPRO_DME_PWR_REQ_POWERMODE		0x094
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER0	0x098
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER1	0x09C
+#define UNIPRO_DME_PWR_REQ_LOCALL2TIMER2	0x0A0
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER0	0x0A4
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER1	0x0A8
+#define UNIPRO_DME_PWR_REQ_REMOTEL2TIMER2	0x0AC
+
+/*
+ * UFS Protector registers
+ */
+#define UFSPRSECURITY	0x010
+#define NSSMU		BIT(14)
+#define UFSPSBEGIN0	0x200
+#define UFSPSEND0	0x204
+#define UFSPSLUN0	0x208
+#define UFSPSCTRL0	0x20C
+
+static void exynos_ufs_auto_ctrl_hcc(struct exynos_ufs *ufs, bool en);
+static void exynos_ufs_ctrl_clkstop(struct exynos_ufs *ufs, bool en);
+
+static inline void exynos_ufs_enable_auto_ctrl_hcc(struct exynos_ufs *ufs)
+{
+	exynos_ufs_auto_ctrl_hcc(ufs, true);
+}
+
+static inline void exynos_ufs_disable_auto_ctrl_hcc(struct exynos_ufs *ufs)
+{
+	exynos_ufs_auto_ctrl_hcc(ufs, false);
+}
+
+static inline void exynos_ufs_disable_auto_ctrl_hcc_save(
+					struct exynos_ufs *ufs, u32 *val)
+{
+	*val = hci_readl(ufs, HCI_MISC);
+	exynos_ufs_auto_ctrl_hcc(ufs, false);
+}
+
+static inline void exynos_ufs_auto_ctrl_hcc_restore(
+					struct exynos_ufs *ufs, u32 *val)
+{
+	hci_writel(ufs, *val, HCI_MISC);
+}
+
+static inline void exynos_ufs_gate_clks(struct exynos_ufs *ufs)
+{
+	exynos_ufs_ctrl_clkstop(ufs, true);
+}
+
+static inline void exynos_ufs_ungate_clks(struct exynos_ufs *ufs)
+{
+	exynos_ufs_ctrl_clkstop(ufs, false);
+}
+
+static int exynos7_ufs_drv_init(struct device *dev, struct exynos_ufs *ufs)
+{
+	return 0;
+}
+
+static int exynos7_ufs_pre_link(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+	for_each_ufs_tx_lane(ufs, i)
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x297, i), 0x17);
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x362, i), 0xff);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x363, i), 0x00);
+	}
+	exynos_ufs_disable_ov_tm(hba);
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN), 0xf);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN), 0xf);
+	for_each_ufs_tx_lane(ufs, i)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB_SEL(TX_HIBERN8_CONTROL, i), 0x0);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_TXPHY_CFGUPDT), 0x1);
+	udelay(1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE), val | (1 << 12));
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_SKIP_RESET_PHY), 0x1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_SKIP_LINE_RESET), 0x1);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_LINE_RESET_REQ), 0x1);
+	udelay(1600);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE), val);
+
+	return 0;
+}
+
+static int exynos7_ufs_post_link(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+	for_each_ufs_tx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x28b, i), 0x83);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x29a, i), 0x07);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(0x277, i),
+			TX_LINERESET_N(exynos_ufs_calc_time_cntr(ufs, 200000)));
+	}
+	exynos_ufs_disable_ov_tm(hba);
+
+	exynos_ufs_enable_dbg_mode(hba);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_SAVECONFIGTIME), 0xbb8);
+	exynos_ufs_disable_dbg_mode(hba);
+
+	return 0;
+}
+
+static int exynos7_ufs_pre_pwr_change(struct exynos_ufs *ufs,
+						struct uic_pwr_mode *pwr)
+{
+	unipro_writel(ufs, 0x22, UNIPRO_DBG_FORCE_DME_CTRL_STATE);
+
+	return 0;
+}
+
+static int exynos7_ufs_post_pwr_change(struct exynos_ufs *ufs,
+						struct uic_pwr_mode *pwr)
+{
+	struct ufs_hba *hba = ufs->hba;
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_RXPHY_CFGUPDT), 0x1);
+
+	if (pwr->lane == 1) {
+		exynos_ufs_enable_dbg_mode(hba);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_CONNECTEDTXDATALANES), 0x1);
+		exynos_ufs_disable_dbg_mode(hba);
+	}
+
+	return 0;
+}
+
+/**
+ * exynos_ufs_auto_ctrl_hcc - HCI core clock control by h/w
+ * Control should be disabled in the below cases
+ * - Before host controller S/W reset
+ * - Access to UFS protector's register
+ */
+static void exynos_ufs_auto_ctrl_hcc(struct exynos_ufs *ufs, bool en)
+{
+	u32 misc = hci_readl(ufs, HCI_MISC);
+
+	if (en)
+		hci_writel(ufs, misc | HCI_CORECLK_CTRL_EN, HCI_MISC);
+	else
+		hci_writel(ufs, misc & ~HCI_CORECLK_CTRL_EN, HCI_MISC);
+}
+
+static void exynos_ufs_ctrl_clkstop(struct exynos_ufs *ufs, bool en)
+{
+	u32 ctrl = hci_readl(ufs, HCI_CLKSTOP_CTRL);
+	u32 misc = hci_readl(ufs, HCI_MISC);
+
+	if (en) {
+		hci_writel(ufs, misc | CLK_CTRL_EN_MASK, HCI_MISC);
+		hci_writel(ufs, ctrl | CLK_STOP_MASK, HCI_CLKSTOP_CTRL);
+	} else {
+		hci_writel(ufs, ctrl & ~CLK_STOP_MASK, HCI_CLKSTOP_CTRL);
+		hci_writel(ufs, misc & ~CLK_CTRL_EN_MASK, HCI_MISC);
+	}
+}
+
+static int exynos_ufs_get_clk_info(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct list_head *head = &hba->clk_list_head;
+	struct ufs_clk_info *clki;
+	u32 pclk_rate;
+	u32 f_min, f_max;
+	u8 div = 0;
+	int ret = 0;
+
+	if (!head || list_empty(head))
+		goto out;
+
+	list_for_each_entry(clki, head, list) {
+		if (!IS_ERR(clki->clk)) {
+			if (!strcmp(clki->name, "core_clk"))
+				ufs->clk_hci_core = clki->clk;
+			else if (!strcmp(clki->name, "sclk_unipro_main"))
+				ufs->clk_unipro_main = clki->clk;
+		}
+	}
+
+	if (!ufs->clk_hci_core || !ufs->clk_unipro_main) {
+		dev_err(hba->dev, "failed to get clk info\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ufs->mclk_rate = clk_get_rate(ufs->clk_unipro_main);
+	pclk_rate = clk_get_rate(ufs->clk_hci_core);
+	f_min = ufs->pclk_avail_min;
+	f_max = ufs->pclk_avail_max;
+
+	if (ufs->opts & EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL) {
+		do {
+			pclk_rate /= (div + 1);
+
+			if (pclk_rate <= f_max)
+				break;
+			div++;
+		} while (pclk_rate >= f_min);
+	}
+
+	if (unlikely(pclk_rate < f_min || pclk_rate > f_max)) {
+		dev_err(hba->dev, "not available pclk range %d\n", pclk_rate);
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ufs->pclk_rate = pclk_rate;
+	ufs->pclk_div = div;
+
+out:
+	return ret;
+}
+
+static void exynos_ufs_set_unipro_pclk_div(struct exynos_ufs *ufs)
+{
+	if (ufs->opts & EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL) {
+		u32 val;
+
+		val = hci_readl(ufs, HCI_UNIPRO_APB_CLK_CTRL);
+		hci_writel(ufs, UNIPRO_APB_CLK(val, ufs->pclk_div),
+			   HCI_UNIPRO_APB_CLK_CTRL);
+	}
+}
+
+static void exynos_ufs_set_pwm_clk_div(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(CMN_PWM_CLK_CTRL), attr->cmn_pwm_clk_ctrl);
+}
+
+static void exynos_ufs_calc_pwm_clk_div(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	const unsigned int div = 30, mult = 20;
+	const unsigned long pwm_min = 3 * 1000 * 1000;
+	const unsigned long pwm_max = 9 * 1000 * 1000;
+	const int divs[] = {32, 16, 8, 4};
+	unsigned long clk = 0, _clk, clk_period;
+	int i = 0, clk_idx = -1;
+
+	clk_period = UNIPRO_PCLK_PERIOD(ufs);
+	for (i = 0; i < ARRAY_SIZE(divs); i++) {
+		_clk = NSEC_PER_SEC * mult / (clk_period * divs[i] * div);
+		if (_clk >= pwm_min && _clk <= pwm_max) {
+			if (_clk > clk) {
+				clk_idx = i;
+				clk = _clk;
+			}
+		}
+	}
+
+	if (clk_idx == -1) {
+		ufshcd_dme_get(hba, UIC_ARG_MIB(CMN_PWM_CLK_CTRL), &clk_idx);
+		dev_err(hba->dev,
+			"failed to decide pwm clock divider, will not change\n");
+	}
+
+	attr->cmn_pwm_clk_ctrl = clk_idx & PWM_CLK_CTRL_MASK;
+}
+
+long exynos_ufs_calc_time_cntr(struct exynos_ufs *ufs, long period)
+{
+	const int precise = 10;
+	long pclk_rate = ufs->pclk_rate;
+	long clk_period, fraction;
+
+	clk_period = UNIPRO_PCLK_PERIOD(ufs);
+	fraction = ((NSEC_PER_SEC % pclk_rate) * precise) / pclk_rate;
+
+	return (period * precise) / ((clk_period * precise) + fraction);
+}
+
+static void exynos_ufs_specify_phy_time_attr(struct exynos_ufs *ufs)
+{
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	struct ufs_phy_time_cfg *t_cfg = &ufs->t_cfg;
+
+	t_cfg->tx_linereset_p =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_dif_p_nsec);
+	t_cfg->tx_linereset_n =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_dif_n_nsec);
+	t_cfg->tx_high_z_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_high_z_cnt_nsec);
+	t_cfg->tx_base_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_base_unit_nsec);
+	t_cfg->tx_gran_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_gran_unit_nsec);
+	t_cfg->tx_sleep_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->tx_sleep_cnt);
+
+	t_cfg->rx_linereset =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_dif_p_nsec);
+	t_cfg->rx_hibern8_wait =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_hibern8_wait_nsec);
+	t_cfg->rx_base_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_base_unit_nsec);
+	t_cfg->rx_gran_n_val =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_gran_unit_nsec);
+	t_cfg->rx_sleep_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_sleep_cnt);
+	t_cfg->rx_stall_cnt =
+		exynos_ufs_calc_time_cntr(ufs, attr->rx_stall_cnt);
+}
+
+static void exynos_ufs_config_phy_time_attr(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct ufs_phy_time_cfg *t_cfg = &ufs->t_cfg;
+	int i;
+
+	exynos_ufs_set_pwm_clk_div(ufs);
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_FILLER_ENABLE, i),
+				ufs->drv_data->uic_attr->rx_filler_enable);
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_LINERESET_VAL, i),
+				RX_LINERESET(t_cfg->rx_linereset));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_BASE_NVAL_07_00, i),
+				RX_BASE_NVAL_L(t_cfg->rx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_BASE_NVAL_15_08, i),
+				RX_BASE_NVAL_H(t_cfg->rx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_GRAN_NVAL_07_00, i),
+				RX_GRAN_NVAL_L(t_cfg->rx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_GRAN_NVAL_10_08, i),
+				RX_GRAN_NVAL_H(t_cfg->rx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_OV_SLEEP_CNT_TIMER, i),
+				RX_OV_SLEEP_CNT(t_cfg->rx_sleep_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(RX_OV_STALL_CNT_TIMER, i),
+				RX_OV_STALL_CNT(t_cfg->rx_stall_cnt));
+	}
+
+	for_each_ufs_tx_lane(ufs, i) {
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_LINERESET_P_VAL, i),
+				TX_LINERESET_P(t_cfg->tx_linereset_p));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_HIGH_Z_CNT_07_00, i),
+				TX_HIGH_Z_CNT_L(t_cfg->tx_high_z_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_HIGH_Z_CNT_11_08, i),
+				TX_HIGH_Z_CNT_H(t_cfg->tx_high_z_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_BASE_NVAL_07_00, i),
+				TX_BASE_NVAL_L(t_cfg->tx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_BASE_NVAL_15_08, i),
+				TX_BASE_NVAL_H(t_cfg->tx_base_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_GRAN_NVAL_07_00, i),
+				TX_GRAN_NVAL_L(t_cfg->tx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_GRAN_NVAL_10_08, i),
+				TX_GRAN_NVAL_H(t_cfg->tx_gran_n_val));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_OV_SLEEP_CNT_TIMER, i),
+				TX_OV_H8_ENTER_EN |
+				TX_OV_SLEEP_CNT(t_cfg->tx_sleep_cnt));
+		ufshcd_dme_set(hba, UIC_ARG_MIB_SEL(TX_MIN_ACTIVATETIME, i),
+				ufs->drv_data->uic_attr->tx_min_activatetime);
+	}
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static void exynos_ufs_config_phy_cap_attr(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+	int i;
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i) {
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G1_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g1_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G2_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g2_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G3_SYNC_LENGTH_CAP, i),
+				attr->rx_hs_g3_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G1_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g1_prep_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G2_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g2_prep_sync_len_cap);
+		ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_HS_G3_PREP_LENGTH_CAP, i),
+				attr->rx_hs_g3_prep_sync_len_cap);
+	}
+
+	if (attr->rx_adv_fine_gran_sup_en == 0) {
+		for_each_ufs_rx_lane(ufs, i) {
+			ufshcd_dme_set(hba,
+				UIC_ARG_MIB_SEL(RX_ADV_GRANULARITY_CAP, i), 0);
+
+			if (attr->rx_min_actv_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_MIN_ACTIVATETIME_CAP,
+						i), attr->rx_min_actv_time_cap);
+
+			if (attr->rx_hibern8_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_HIBERN8TIME_CAP, i),
+						attr->rx_hibern8_time_cap);
+		}
+	} else if (attr->rx_adv_fine_gran_sup_en == 1) {
+		for_each_ufs_rx_lane(ufs, i) {
+			if (attr->rx_adv_fine_gran_step)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_ADV_GRANULARITY_CAP,
+						i), RX_ADV_FINE_GRAN_STEP(
+						attr->rx_adv_fine_gran_step));
+
+			if (attr->rx_adv_min_actv_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(
+						RX_ADV_MIN_ACTIVATETIME_CAP, i),
+						attr->rx_adv_min_actv_time_cap);
+
+			if (attr->rx_adv_hibern8_time_cap)
+				ufshcd_dme_set(hba,
+					UIC_ARG_MIB_SEL(RX_ADV_HIBERN8TIME_CAP,
+						i),
+						attr->rx_adv_hibern8_time_cap);
+		}
+	}
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static void exynos_ufs_establish_connt(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	enum {
+		DEV_ID		= 0x00,
+		PEER_DEV_ID	= 0x01,
+		PEER_CPORT_ID	= 0x00,
+		TRAFFIC_CLASS	= 0x00,
+	};
+
+	/* allow cport attributes to be set */
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), CPORT_IDLE);
+
+	/* local unipro attributes */
+	ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID), DEV_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(N_DEVICEID_VALID), TRUE);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERDEVICEID), PEER_DEV_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_PEERCPORTID), PEER_CPORT_ID);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CPORTFLAGS), CPORT_DEF_FLAGS);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_TRAFFICCLASS), TRAFFIC_CLASS);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(T_CONNECTIONSTATE), CPORT_CONNECTED);
+}
+
+static void exynos_ufs_config_smu(struct exynos_ufs *ufs)
+{
+	u32 reg, val;
+
+	exynos_ufs_disable_auto_ctrl_hcc_save(ufs, &val);
+
+	/* make encryption disabled by default */
+	reg = ufsp_readl(ufs, UFSPRSECURITY);
+	ufsp_writel(ufs, reg | NSSMU, UFSPRSECURITY);
+	ufsp_writel(ufs, 0x0, UFSPSBEGIN0);
+	ufsp_writel(ufs, 0xffffffff, UFSPSEND0);
+	ufsp_writel(ufs, 0xff, UFSPSLUN0);
+	ufsp_writel(ufs, 0xf1, UFSPSCTRL0);
+
+	exynos_ufs_auto_ctrl_hcc_restore(ufs, &val);
+}
+
+static void exynos_ufs_config_sync_pattern_mask(struct exynos_ufs *ufs,
+					struct uic_pwr_mode *pwr)
+{
+	struct ufs_hba *hba = ufs->hba;
+	u8 g = pwr->gear;
+	u32 mask, sync_len;
+	enum {
+		SYNC_LEN_G1 = 80 * 1000, /* 80us */
+		SYNC_LEN_G2 = 40 * 1000, /* 44us */
+		SYNC_LEN_G3 = 20 * 1000, /* 20us */
+	};
+	int i;
+
+	if (g == 1)
+		sync_len = SYNC_LEN_G1;
+	else if (g == 2)
+		sync_len = SYNC_LEN_G2;
+	else if (g == 3)
+		sync_len = SYNC_LEN_G3;
+	else
+		return;
+
+	mask = exynos_ufs_calc_time_cntr(ufs, sync_len);
+	mask = (mask >> 8) & 0xff;
+
+	exynos_ufs_enable_ov_tm(hba);
+
+	for_each_ufs_rx_lane(ufs, i)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB_SEL(RX_SYNC_MASK_LENGTH, i), mask);
+
+	exynos_ufs_disable_ov_tm(hba);
+}
+
+static int exynos_ufs_pre_pwr_mode(struct ufs_hba *hba,
+				struct ufs_pa_layer_attr *pwr_max,
+				struct ufs_pa_layer_attr *final)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct uic_pwr_mode *pwr_req = &ufs->pwr_req;
+	struct uic_pwr_mode *pwr_act = &ufs->pwr_act;
+
+	final->gear_rx
+		= pwr_act->gear = min_t(u32, pwr_max->gear_rx, pwr_req->gear);
+	final->gear_tx
+		= pwr_act->gear = min_t(u32, pwr_max->gear_tx, pwr_req->gear);
+	final->lane_rx
+		= pwr_act->lane = min_t(u32, pwr_max->lane_rx, pwr_req->lane);
+	final->lane_tx
+		= pwr_act->lane = min_t(u32, pwr_max->lane_tx, pwr_req->lane);
+	final->pwr_rx = pwr_act->mode = pwr_req->mode;
+	final->pwr_tx = pwr_act->mode = pwr_req->mode;
+	final->hs_rate = pwr_act->hs_series = pwr_req->hs_series;
+
+	/* save and configure l2 timer */
+	pwr_act->l_l2_timer[0] = pwr_req->l_l2_timer[0];
+	pwr_act->l_l2_timer[1] = pwr_req->l_l2_timer[1];
+	pwr_act->l_l2_timer[2] = pwr_req->l_l2_timer[2];
+	pwr_act->r_l2_timer[0] = pwr_req->r_l2_timer[0];
+	pwr_act->r_l2_timer[1] = pwr_req->r_l2_timer[1];
+	pwr_act->r_l2_timer[2] = pwr_req->r_l2_timer[2];
+
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_FC0PROTTIMEOUTVAL), pwr_act->l_l2_timer[0]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_TC0REPLAYTIMEOUTVAL), pwr_act->l_l2_timer[1]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(DL_AFC0REQTIMEOUTVAL), pwr_act->l_l2_timer[2]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA0), pwr_act->r_l2_timer[0]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA1), pwr_act->r_l2_timer[1]);
+	ufshcd_dme_set(hba,
+		UIC_ARG_MIB(PA_PWRMODEUSERDATA2), pwr_act->r_l2_timer[2]);
+
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[0], UNIPRO_DME_PWR_REQ_LOCALL2TIMER0);
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[1], UNIPRO_DME_PWR_REQ_LOCALL2TIMER1);
+	unipro_writel(ufs,
+		pwr_act->l_l2_timer[2], UNIPRO_DME_PWR_REQ_LOCALL2TIMER2);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[0], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER0);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[1], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER1);
+	unipro_writel(ufs,
+		pwr_act->r_l2_timer[2], UNIPRO_DME_PWR_REQ_REMOTEL2TIMER2);
+
+	if (ufs->drv_data->pre_pwr_change)
+		ufs->drv_data->pre_pwr_change(ufs, pwr_act);
+
+	if (IS_UFS_PWR_MODE_HS(pwr_act->mode)) {
+		exynos_ufs_config_sync_pattern_mask(ufs, pwr_act);
+
+		switch (pwr_act->hs_series) {
+		case PA_HS_MODE_A:
+		case PA_HS_MODE_B:
+			phy_calibrate(generic_phy);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+#define PWR_MODE_STR_LEN	64
+static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
+				struct ufs_pa_layer_attr *pwr_max,
+				struct ufs_pa_layer_attr *pwr_req)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct uic_pwr_mode *pwr = &ufs->pwr_act;
+	char pwr_str[PWR_MODE_STR_LEN] = "";
+	int ret = 0;
+
+	if (ufs->drv_data->post_pwr_change)
+		ufs->drv_data->post_pwr_change(ufs, pwr);
+
+	if (IS_UFS_PWR_MODE_HS(pwr->mode)) {
+		switch (pwr->hs_series) {
+		case PA_HS_MODE_A:
+		case PA_HS_MODE_B:
+			phy_calibrate(generic_phy);
+			break;
+		}
+
+		snprintf(pwr_str, sizeof(pwr_str), "Fast%s series_%s G_%d L_%d",
+			pwr->mode == FASTAUTO_MODE ? "_Auto" : "",
+			pwr->hs_series == PA_HS_MODE_A ? "A" : "B",
+			pwr->gear, pwr->lane);
+	} else if (IS_UFS_PWR_MODE_PWM(pwr->mode)) {
+		snprintf(pwr_str, sizeof(pwr_str), "Slow%s G_%d L_%d",
+			pwr->mode == SLOWAUTO_MODE ? "_Auto" : "",
+			pwr->gear, pwr->lane);
+	}
+
+	dev_info(hba->dev, "Power mode change %d : %s\n", ret, pwr_str);
+	return ret;
+}
+
+static void exynos_ufs_specify_nexus_t_xfer_req(struct ufs_hba *hba,
+						int tag, bool op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	u32 type;
+
+	type =  hci_readl(ufs, HCI_UTRL_NEXUS_TYPE);
+
+	if (op)
+		hci_writel(ufs, type | (1 << tag), HCI_UTRL_NEXUS_TYPE);
+	else
+		hci_writel(ufs, type & ~(1 << tag), HCI_UTRL_NEXUS_TYPE);
+}
+
+static void exynos_ufs_specify_nexus_t_tm_req(struct ufs_hba *hba,
+						int tag, u8 func)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	u32 type;
+
+	type =  hci_readl(ufs, HCI_UTMRL_NEXUS_TYPE);
+
+	switch (func) {
+	case UFS_ABORT_TASK:
+	case UFS_QUERY_TASK:
+		hci_writel(ufs, type | (1 << tag), HCI_UTMRL_NEXUS_TYPE);
+		break;
+	case UFS_ABORT_TASK_SET:
+	case UFS_CLEAR_TASK_SET:
+	case UFS_LOGICAL_RESET:
+	case UFS_QUERY_TASK_SET:
+		hci_writel(ufs, type & ~(1 << tag), HCI_UTMRL_NEXUS_TYPE);
+		break;
+	}
+}
+
+static void exynos_ufs_phy_init(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+	struct phy *generic_phy = ufs->phy;
+
+	if (ufs->avail_ln_rx == 0 || ufs->avail_ln_tx == 0) {
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_AVAILRXDATALANES),
+			&ufs->avail_ln_rx);
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_AVAILTXDATALANES),
+			&ufs->avail_ln_tx);
+		WARN(ufs->avail_ln_rx != ufs->avail_ln_tx,
+			"available data lane is not equal(rx:%d, tx:%d)\n",
+			ufs->avail_ln_rx, ufs->avail_ln_tx);
+	}
+
+	phy_set_bus_width(generic_phy, ufs->avail_ln_rx);
+	phy_init(generic_phy);
+}
+
+static void exynos_ufs_config_unipro(struct exynos_ufs *ufs)
+{
+	struct ufs_hba *hba = ufs->hba;
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_CLK_PERIOD),
+		DIV_ROUND_UP(NSEC_PER_SEC, ufs->mclk_rate));
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TXTRAILINGCLOCKS),
+			ufs->drv_data->uic_attr->tx_trailingclks);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE),
+			ufs->drv_data->uic_attr->pa_dbg_option_suite);
+}
+
+static void exynos_ufs_config_intr(struct exynos_ufs *ufs, u32 errs, u8 index)
+{
+	switch (index) {
+	case UNIPRO_L1_5:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_PA_LAYER);
+		break;
+	case UNIPRO_L2:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_DL_LAYER);
+		break;
+	case UNIPRO_L3:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_N_LAYER);
+		break;
+	case UNIPRO_L4:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_T_LAYER);
+		break;
+	case UNIPRO_DME:
+		hci_writel(ufs, DFES_ERR_EN | errs, HCI_ERR_EN_DME_LAYER);
+		break;
+	}
+}
+
+static int exynos_ufs_pre_link(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	/* hci */
+	exynos_ufs_config_intr(ufs, DFES_DEF_L2_ERRS, UNIPRO_L2);
+	exynos_ufs_config_intr(ufs, DFES_DEF_L3_ERRS, UNIPRO_L3);
+	exynos_ufs_config_intr(ufs, DFES_DEF_L4_ERRS, UNIPRO_L4);
+	exynos_ufs_set_unipro_pclk_div(ufs);
+
+	/* unipro */
+	exynos_ufs_config_unipro(ufs);
+
+	/* m-phy */
+	exynos_ufs_phy_init(ufs);
+	exynos_ufs_config_phy_time_attr(ufs);
+	exynos_ufs_config_phy_cap_attr(ufs);
+
+	if (ufs->drv_data->pre_link)
+		ufs->drv_data->pre_link(ufs);
+
+	return 0;
+}
+
+static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs)
+{
+	const u8 cntr_div = 40;
+	u32 val;
+
+	val = exynos_ufs_calc_time_cntr(ufs, IATOVAL_NSEC / cntr_div);
+	hci_writel(ufs, val & CNT_VAL_1US_MASK, HCI_1US_TO_CNT_VAL);
+}
+
+static int exynos_ufs_post_link(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct phy *generic_phy = ufs->phy;
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	exynos_ufs_establish_connt(ufs);
+	exynos_ufs_fit_aggr_timeout(ufs);
+
+	hci_writel(ufs, 0xa, HCI_DATA_REORDER);
+	hci_writel(ufs, PRDT_PREFECT_EN | PRDT_SET_SIZE(12),
+			HCI_TXPRDT_ENTRY_SIZE);
+	hci_writel(ufs, PRDT_SET_SIZE(12), HCI_RXPRDT_ENTRY_SIZE);
+	hci_writel(ufs, (1 << hba->nutrs) - 1, HCI_UTRL_NEXUS_TYPE);
+	hci_writel(ufs, (1 << hba->nutmrs) - 1, HCI_UTMRL_NEXUS_TYPE);
+	hci_writel(ufs, 0xf, HCI_AXIDMA_RWDATA_BURST_LEN);
+
+	if (ufs->opts & EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB)
+		ufshcd_dme_set(hba,
+			UIC_ARG_MIB(T_DBG_SKIP_INIT_HIBERN8_EXIT), TRUE);
+
+	if (attr->pa_granularity) {
+		exynos_ufs_enable_dbg_mode(hba);
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_GRANULARITY),
+				attr->pa_granularity);
+		exynos_ufs_disable_dbg_mode(hba);
+
+		if (attr->pa_tactivate)
+			ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TACTIVATE),
+					attr->pa_tactivate);
+		if (attr->pa_hibern8time &&
+		    !(ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER))
+			ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HIBERN8TIME),
+					attr->pa_hibern8time);
+	}
+
+	if (ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER) {
+		if (!attr->pa_granularity)
+			ufshcd_dme_get(hba, UIC_ARG_MIB(PA_GRANULARITY),
+					&attr->pa_granularity);
+		if (!attr->pa_hibern8time)
+			ufshcd_dme_get(hba, UIC_ARG_MIB(PA_HIBERN8TIME),
+					&attr->pa_hibern8time);
+		/*
+		 * not wait for HIBERN8 time to exit hibernation
+		 */
+		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HIBERN8TIME), 0);
+
+		if (attr->pa_granularity < 1 || attr->pa_granularity > 6) {
+			/* Valid range for granularity: 1 ~ 6 */
+			dev_warn(hba->dev,
+				"%s: pa_granularty %d is invalid, assuming backwards compatibility\n",
+				__func__,
+				attr->pa_granularity);
+			attr->pa_granularity = 6;
+		}
+	}
+
+	phy_calibrate(generic_phy);
+
+	if (ufs->drv_data->post_link)
+		ufs->drv_data->post_link(ufs);
+
+	return 0;
+}
+
+static void exynos_ufs_specify_pwr_mode(struct device_node *np,
+				struct exynos_ufs *ufs)
+{
+	struct uic_pwr_mode *pwr = &ufs->pwr_req;
+	const char *str = NULL;
+
+	if (!of_property_read_string(np, "ufs,pwr-attr-mode", &str)) {
+		if (!strncmp(str, "FAST", sizeof("FAST")))
+			pwr->mode = FAST_MODE;
+		else if (!strncmp(str, "SLOW", sizeof("SLOW")))
+			pwr->mode = SLOW_MODE;
+		else if (!strncmp(str, "FAST_auto", sizeof("FAST_auto")))
+			pwr->mode = FASTAUTO_MODE;
+		else if (!strncmp(str, "SLOW_auto", sizeof("SLOW_auto")))
+			pwr->mode = SLOWAUTO_MODE;
+		else
+			pwr->mode = FAST_MODE;
+	} else {
+		pwr->mode = FAST_MODE;
+	}
+
+	if (of_property_read_u32(np, "ufs,pwr-attr-lane", &pwr->lane))
+		pwr->lane = 1;
+
+	if (of_property_read_u32(np, "ufs,pwr-attr-gear", &pwr->gear))
+		pwr->gear = 1;
+
+	if (IS_UFS_PWR_MODE_HS(pwr->mode)) {
+		if (!of_property_read_string(np,
+					"ufs,pwr-attr-hs-series", &str)) {
+			if (!strncmp(str, "HS_rate_a", sizeof("HS_rate_a")))
+				pwr->hs_series = PA_HS_MODE_A;
+			else if (!strncmp(str, "HS_rate_b",
+				    sizeof("HS_rate_b")))
+				pwr->hs_series = PA_HS_MODE_B;
+			else
+				pwr->hs_series = PA_HS_MODE_A;
+		} else {
+			pwr->hs_series = PA_HS_MODE_A;
+		}
+	}
+
+	if (of_property_read_u32_array(
+		np, "ufs,pwr-local-l2-timer", pwr->l_l2_timer, 3)) {
+		pwr->l_l2_timer[0] = FC0PROTTIMEOUTVAL;
+		pwr->l_l2_timer[1] = TC0REPLAYTIMEOUTVAL;
+		pwr->l_l2_timer[2] = AFC0REQTIMEOUTVAL;
+	}
+
+	if (of_property_read_u32_array(
+		np, "ufs,pwr-remote-l2-timer", pwr->r_l2_timer, 3)) {
+		pwr->r_l2_timer[0] = FC0PROTTIMEOUTVAL;
+		pwr->r_l2_timer[1] = TC0REPLAYTIMEOUTVAL;
+		pwr->r_l2_timer[2] = AFC0REQTIMEOUTVAL;
+	}
+}
+
+static int exynos_ufs_parse_dt(struct device *dev, struct exynos_ufs *ufs)
+{
+	struct device_node *np = dev->of_node;
+	struct exynos_ufs_drv_data *drv_data = &exynos_ufs_drvs;
+	struct exynos_ufs_uic_attr *attr;
+	u32 freq[2];
+	int ret;
+
+	while (drv_data->compatible) {
+		if (of_device_is_compatible(np, drv_data->compatible)) {
+			ufs->drv_data = drv_data;
+			break;
+		}
+		drv_data++;
+	}
+
+	if (ufs->drv_data && ufs->drv_data->uic_attr) {
+		attr = ufs->drv_data->uic_attr;
+	} else {
+		dev_err(dev, "failed to get uic attributes\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = of_property_read_u32_array(np,
+			"pclk-freq-avail-range", freq, ARRAY_SIZE(freq));
+	if (!ret) {
+		ufs->pclk_avail_min = freq[0];
+		ufs->pclk_avail_max = freq[1];
+	} else {
+		dev_err(dev, "failed to get available pclk range\n");
+		goto out;
+	}
+
+	exynos_ufs_specify_pwr_mode(np, ufs);
+
+	if (!of_property_read_u32(np, "ufs-rx-adv-fine-gran-sup_en",
+				&attr->rx_adv_fine_gran_sup_en)) {
+		if (attr->rx_adv_fine_gran_sup_en == 0) {
+			/* 100us step */
+			if (of_property_read_u32(np,
+					"ufs-rx-min-activate-time-cap",
+					&attr->rx_min_actv_time_cap))
+				dev_warn(dev,
+					"ufs-rx-min-activate-time-cap is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-hibern8-time-cap",
+					&attr->rx_hibern8_time_cap))
+				dev_warn(dev,
+					"ufs-rx-hibern8-time-cap is empty\n");
+		} else if (attr->rx_adv_fine_gran_sup_en == 1) {
+			/* fine granularity step */
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-fine-gran-step",
+					&attr->rx_adv_fine_gran_step))
+				dev_warn(dev,
+					"ufs-rx-adv-fine-gran-step is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-min-activate-time-cap",
+					&attr->rx_adv_min_actv_time_cap))
+				dev_warn(dev,
+					"ufs-rx-adv-min-activate-time-cap is empty\n");
+
+			if (of_property_read_u32(np,
+					"ufs-rx-adv-hibern8-time-cap",
+					&attr->rx_adv_hibern8_time_cap))
+				dev_warn(dev,
+					"ufs-rx-adv-hibern8-time-cap is empty\n");
+		} else {
+			dev_warn(dev,
+				"not supported val for ufs-rx-adv-fine-gran-sup_en %d\n",
+				attr->rx_adv_fine_gran_sup_en);
+		}
+	} else {
+		attr->rx_adv_fine_gran_sup_en = 0xf;
+	}
+
+	if (!of_property_read_u32(np,
+				"ufs-pa-granularity", &attr->pa_granularity)) {
+		if (of_property_read_u32(np,
+				"ufs-pa-tacctivate", &attr->pa_tactivate))
+			dev_warn(dev, "ufs-pa-tacctivate is empty\n");
+
+		if (of_property_read_u32(np,
+				"ufs-pa-hibern8time", &attr->pa_hibern8time))
+			dev_warn(dev, "ufs-pa-hibern8time is empty\n");
+	}
+
+out:
+	return ret;
+}
+
+static int exynos_ufs_init(struct ufs_hba *hba)
+{
+	struct device *dev = hba->dev;
+	struct platform_device *pdev = to_platform_device(dev);
+	struct exynos_ufs *ufs;
+	struct resource *res;
+	int ret;
+
+	ufs = devm_kzalloc(dev, sizeof(*ufs), GFP_KERNEL);
+	if (!ufs)
+		return -ENOMEM;
+
+	/* exynos-specific hci */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "vs_hci");
+	ufs->reg_hci = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_hci) {
+		dev_err(dev, "cannot ioremap for hci vendor register\n");
+		return -ENOMEM;
+	}
+
+	/* unipro */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "unipro");
+	ufs->reg_unipro = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_unipro) {
+		dev_err(dev, "cannot ioremap for unipro register\n");
+		return -ENOMEM;
+	}
+
+	/* ufs protector */
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ufsp");
+	ufs->reg_ufsp = devm_ioremap_resource(dev, res);
+	if (!ufs->reg_ufsp) {
+		dev_err(dev, "cannot ioremap for ufs protector register\n");
+		return -ENOMEM;
+	}
+
+	ret = exynos_ufs_parse_dt(dev, ufs);
+	if (ret) {
+		dev_err(dev, "failed to get dt info.\n");
+		goto out;
+	}
+
+	ufs->phy = devm_phy_get(dev, "ufs-phy");
+	if (IS_ERR(ufs->phy)) {
+		ret = PTR_ERR(ufs->phy);
+		dev_err(dev, "failed to get ufs-phy\n");
+		goto out;
+	}
+
+	ret = phy_power_on(ufs->phy);
+	if (ret)
+		goto phy_exit;
+
+	ufs->hba = hba;
+	ufs->opts = ufs->drv_data->opts |
+		EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB |
+		EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER;
+	ufs->rx_sel_idx = PA_MAXDATALANES;
+	if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX)
+		ufs->rx_sel_idx = 0;
+	hba->priv = (void *)ufs;
+	hba->quirks = ufs->drv_data->quirks;
+	if (ufs->drv_data->drv_init) {
+		ret = ufs->drv_data->drv_init(dev, ufs);
+		if (ret) {
+			dev_err(dev, "failed to init drv-data\n");
+			goto phy_off;
+		}
+	}
+
+	ret = exynos_ufs_get_clk_info(ufs);
+	if (ret)
+		goto phy_off;
+	exynos_ufs_specify_phy_time_attr(ufs);
+	exynos_ufs_config_smu(ufs);
+	return 0;
+
+phy_off:
+	phy_power_off(ufs->phy);
+phy_exit:
+	phy_exit(ufs->phy);
+	hba->priv = NULL;
+out:
+	return ret;
+}
+
+static int exynos_ufs_host_reset(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	unsigned long timeout = jiffies + msecs_to_jiffies(1);
+	u32 val;
+	int ret = 0;
+
+	exynos_ufs_disable_auto_ctrl_hcc_save(ufs, &val);
+
+	hci_writel(ufs, UFS_SW_RST_MASK, HCI_SW_RST);
+
+	do {
+		if (!(hci_readl(ufs, HCI_SW_RST) & UFS_SW_RST_MASK))
+			goto out;
+	} while (time_before(jiffies, timeout));
+
+	dev_err(hba->dev, "timeout host sw-reset\n");
+	ret = -ETIMEDOUT;
+
+out:
+	exynos_ufs_auto_ctrl_hcc_restore(ufs, &val);
+	return ret;
+}
+
+static void exynos_ufs_dev_hw_reset(struct ufs_hba *hba)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	hci_writel(ufs, 0 << 0, HCI_GPIO_OUT);
+	udelay(5);
+	hci_writel(ufs, 1 << 0, HCI_GPIO_OUT);
+}
+
+static void exynos_ufs_pre_hibern8(struct ufs_hba *hba, u8 enter)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	struct exynos_ufs_uic_attr *attr = ufs->drv_data->uic_attr;
+
+	if (!enter) {
+		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
+			exynos_ufs_disable_auto_ctrl_hcc(ufs);
+		exynos_ufs_ungate_clks(ufs);
+
+		if (ufs->opts & EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER) {
+			const unsigned int granularity_tbl[] = {
+				1, 4, 8, 16, 32, 100
+			};
+			int h8_time = attr->pa_hibern8time *
+				granularity_tbl[attr->pa_granularity - 1];
+			unsigned long us;
+			s64 delta;
+
+			do {
+				delta = h8_time - ktime_us_delta(ktime_get(),
+							ufs->entry_hibern8_t);
+				if (delta <= 0)
+					break;
+
+				us = min_t(s64, delta, USEC_PER_MSEC);
+				if (us >= 10)
+					usleep_range(us, us + 10);
+			} while (1);
+		}
+	}
+}
+
+static void exynos_ufs_post_hibern8(struct ufs_hba *hba, u8 enter)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!enter) {
+		struct uic_pwr_mode *pwr = &ufs->pwr_act;
+		u32 mode = 0;
+
+		ufshcd_dme_get(hba, UIC_ARG_MIB(PA_PWRMODE), &mode);
+		if (mode != (pwr->mode << 4 | pwr->mode)) {
+			dev_warn(hba->dev, "%s: power mode change\n", __func__);
+			hba->pwr_info.pwr_rx = (mode >> 4) & 0xf;
+			hba->pwr_info.pwr_tx = mode & 0xf;
+			ufshcd_config_pwr_mode(hba, &hba->max_pwr_info.info);
+		}
+
+		if (!(ufs->opts & EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB))
+			exynos_ufs_establish_connt(ufs);
+	} else {
+		ufs->entry_hibern8_t = ktime_get();
+		exynos_ufs_gate_clks(ufs);
+		if (ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL)
+			exynos_ufs_enable_auto_ctrl_hcc(ufs);
+	}
+}
+
+static int exynos_ufs_hce_enable_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_host_reset(hba);
+		if (ret)
+			return ret;
+		exynos_ufs_dev_hw_reset(hba);
+		break;
+	case POST_CHANGE:
+		exynos_ufs_calc_pwm_clk_div(ufs);
+		if (!(ufs->opts & EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL))
+			exynos_ufs_enable_auto_ctrl_hcc(ufs);
+		break;
+	}
+
+	return ret;
+}
+
+static int exynos_ufs_link_startup_notify(struct ufs_hba *hba,
+					  enum ufs_notify_change_status status)
+{
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_pre_link(hba);
+		break;
+	case POST_CHANGE:
+		ret = exynos_ufs_post_link(hba);
+		break;
+	}
+
+	return ret;
+}
+
+static int exynos_ufs_pwr_change_notify(struct ufs_hba *hba,
+					enum ufs_notify_change_status status,
+					struct ufs_pa_layer_attr *pwr_max,
+					struct ufs_pa_layer_attr *pwr_req)
+{
+	int ret = 0;
+
+	switch (status) {
+	case PRE_CHANGE:
+		ret = exynos_ufs_pre_pwr_mode(hba, pwr_max, pwr_req);
+		break;
+	case POST_CHANGE:
+		ret = exynos_ufs_post_pwr_mode(hba, NULL, pwr_req);
+		break;
+	}
+
+	return ret;
+}
+
+static void exynos_ufs_hibern8_notify(struct ufs_hba *hba,
+				     enum uic_cmd_dme enter,
+				     enum ufs_notify_change_status notify)
+{
+	switch ((u8)notify) {
+	case PRE_CHANGE:
+		exynos_ufs_pre_hibern8(hba, enter);
+		break;
+	case POST_CHANGE:
+		exynos_ufs_post_hibern8(hba, enter);
+		break;
+	}
+}
+
+static int exynos_ufs_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!ufshcd_is_link_active(hba))
+		phy_power_off(ufs->phy);
+
+	return 0;
+}
+
+static int exynos_ufs_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
+{
+	struct exynos_ufs *ufs = ufshcd_get_variant(hba);
+
+	if (!ufshcd_is_link_active(hba))
+		phy_power_on(ufs->phy);
+
+	exynos_ufs_config_smu(ufs);
+
+	return 0;
+}
+
+static struct ufs_hba_variant_ops ufs_hba_exynos_ops = {
+	.name				= "exynos_ufs",
+	.init				= exynos_ufs_init,
+	.hce_enable_notify		= exynos_ufs_hce_enable_notify,
+	.link_startup_notify		= exynos_ufs_link_startup_notify,
+	.pwr_change_notify		= exynos_ufs_pwr_change_notify,
+	.setup_xfer_req			= exynos_ufs_specify_nexus_t_xfer_req,
+	.setup_task_mgmt		= exynos_ufs_specify_nexus_t_tm_req,
+	.hibern8_notify			= exynos_ufs_hibern8_notify,
+	.suspend			= exynos_ufs_suspend,
+	.resume				= exynos_ufs_resume,
+};
+
+static int exynos_ufs_probe(struct platform_device *pdev)
+{
+	int err;
+	struct device *dev = &pdev->dev;
+
+	err = ufshcd_pltfrm_init(pdev, &ufs_hba_exynos_ops);
+	if (err)
+		dev_err(dev, "ufshcd_pltfrm_init() failed %d\n", err);
+
+	return err;
+}
+
+static int exynos_ufs_remove(struct platform_device *pdev)
+{
+	struct ufs_hba *hba =  platform_get_drvdata(pdev);
+
+	pm_runtime_get_sync(&(pdev)->dev);
+	ufshcd_remove(hba);
+	return 0;
+}
+
+struct exynos_ufs_drv_data exynos_ufs_drvs = {
+
+	.compatible		= "samsung,exynos7-ufs",
+	.uic_attr		= &exynos7_uic_attr,
+	.quirks			= UFSHCD_QUIRK_PRDT_BYTE_GRAN |
+				  UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
+				  UFSHCI_QUIRK_BROKEN_HCE |
+				  UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
+	.opts			= EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
+				  EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
+				  EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
+	.drv_init		= exynos7_ufs_drv_init,
+	.pre_link		= exynos7_ufs_pre_link,
+	.post_link		= exynos7_ufs_post_link,
+	.pre_pwr_change		= exynos7_ufs_pre_pwr_change,
+	.post_pwr_change	= exynos7_ufs_post_pwr_change,
+};
+
+static const struct of_device_id exynos_ufs_of_match[] = {
+	{ .compatible = "samsung,exynos7-ufs",
+	  .data	      = &exynos_ufs_drvs },
+	{},
+};
+
+static const struct dev_pm_ops exynos_ufs_pm_ops = {
+	.suspend	= ufshcd_pltfrm_suspend,
+	.resume		= ufshcd_pltfrm_resume,
+	.runtime_suspend = ufshcd_pltfrm_runtime_suspend,
+	.runtime_resume  = ufshcd_pltfrm_runtime_resume,
+	.runtime_idle    = ufshcd_pltfrm_runtime_idle,
+};
+
+static struct platform_driver exynos_ufs_pltform = {
+	.probe	= exynos_ufs_probe,
+	.remove	= exynos_ufs_remove,
+	.shutdown = ufshcd_pltfrm_shutdown,
+	.driver	= {
+		.name	= "exynos-ufshc",
+		.pm	= &exynos_ufs_pm_ops,
+		.of_match_table = of_match_ptr(exynos_ufs_of_match),
+	},
+};
+module_platform_driver(exynos_ufs_pltform);
diff --git a/drivers/scsi/ufs/ufs-exynos.h b/drivers/scsi/ufs/ufs-exynos.h
new file mode 100644
index 000000000000..98efffc2c19a
--- /dev/null
+++ b/drivers/scsi/ufs/ufs-exynos.h
@@ -0,0 +1,268 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * UFS Host Controller driver for Exynos specific extensions
+ *
+ * Copyright (C) 2014-2015 Samsung Electronics Co., Ltd.
+ *
+ */
+
+#ifndef _UFS_EXYNOS_H_
+#define _UFS_EXYNOS_H_
+
+/*
+ * UNIPRO registers
+ */
+#define UNIPRO_DBG_FORCE_DME_CTRL_STATE		0x150
+
+/*
+ * MIBs for PA debug registers
+ */
+#define PA_DBG_CLK_PERIOD	0x9514
+#define PA_DBG_TXPHY_CFGUPDT	0x9518
+#define PA_DBG_RXPHY_CFGUPDT	0x9519
+#define PA_DBG_MODE		0x9529
+#define PA_DBG_SKIP_RESET_PHY	0x9539
+#define PA_DBG_OV_TM		0x9540
+#define PA_DBG_SKIP_LINE_RESET	0x9541
+#define PA_DBG_LINE_RESET_REQ	0x9543
+#define PA_DBG_OPTION_SUITE	0x9564
+#define PA_DBG_OPTION_SUITE_DYN	0x9565
+
+/*
+ * MIBs for Transport Layer debug registers
+ */
+#define T_DBG_SKIP_INIT_HIBERN8_EXIT	0xc001
+
+/*
+ * Exynos MPHY attributes
+ */
+#define TX_LINERESET_N_VAL	0x0277
+#define TX_LINERESET_N(v)	(((v) >> 10) & 0xFF)
+#define TX_LINERESET_P_VAL	0x027D
+#define TX_LINERESET_P(v)	(((v) >> 12) & 0xFF)
+#define TX_OV_SLEEP_CNT_TIMER	0x028E
+#define TX_OV_H8_ENTER_EN	(1 << 7)
+#define TX_OV_SLEEP_CNT(v)	(((v) >> 5) & 0x7F)
+#define TX_HIGH_Z_CNT_11_08	0x028C
+#define TX_HIGH_Z_CNT_H(v)	(((v) >> 8) & 0xF)
+#define TX_HIGH_Z_CNT_07_00	0x028D
+#define TX_HIGH_Z_CNT_L(v)	((v) & 0xFF)
+#define TX_BASE_NVAL_07_00	0x0293
+#define TX_BASE_NVAL_L(v)	((v) & 0xFF)
+#define TX_BASE_NVAL_15_08	0x0294
+#define TX_BASE_NVAL_H(v)	(((v) >> 8) & 0xFF)
+#define TX_GRAN_NVAL_07_00	0x0295
+#define TX_GRAN_NVAL_L(v)	((v) & 0xFF)
+#define TX_GRAN_NVAL_10_08	0x0296
+#define TX_GRAN_NVAL_H(v)	(((v) >> 8) & 0x3)
+
+#define RX_FILLER_ENABLE	0x0316
+#define RX_FILLER_EN		(1 << 1)
+#define RX_LINERESET_VAL	0x0317
+#define RX_LINERESET(v)	(((v) >> 12) & 0xFF)
+#define RX_LCC_IGNORE		0x0318
+#define RX_SYNC_MASK_LENGTH	0x0321
+#define RX_HIBERN8_WAIT_VAL_BIT_20_16	0x0331
+#define RX_HIBERN8_WAIT_VAL_BIT_15_08	0x0332
+#define RX_HIBERN8_WAIT_VAL_BIT_07_00	0x0333
+#define RX_OV_SLEEP_CNT_TIMER	0x0340
+#define RX_OV_SLEEP_CNT(v)	(((v) >> 6) & 0x1F)
+#define RX_OV_STALL_CNT_TIMER	0x0341
+#define RX_OV_STALL_CNT(v)	(((v) >> 4) & 0xFF)
+#define RX_BASE_NVAL_07_00	0x0355
+#define RX_BASE_NVAL_L(v)	((v) & 0xFF)
+#define RX_BASE_NVAL_15_08	0x0354
+#define RX_BASE_NVAL_H(v)	(((v) >> 8) & 0xFF)
+#define RX_GRAN_NVAL_07_00	0x0353
+#define RX_GRAN_NVAL_L(v)	((v) & 0xFF)
+#define RX_GRAN_NVAL_10_08	0x0352
+#define RX_GRAN_NVAL_H(v)	(((v) >> 8) & 0x3)
+
+#define CMN_PWM_CLK_CTRL	0x0402
+#define PWM_CLK_CTRL_MASK	0x3
+
+#define IATOVAL_NSEC		20000	/* unit: ns */
+#define UNIPRO_PCLK_PERIOD(ufs) (NSEC_PER_SEC / ufs->pclk_rate)
+
+struct exynos_ufs;
+
+struct uic_pwr_mode {
+	u32 lane;
+	u32 gear;
+	u8 mode;
+	u8 hs_series;
+	u32 l_l2_timer[3];	/* local */
+	u32 r_l2_timer[3];	/* remote */
+};
+
+struct exynos_ufs_uic_attr {
+	/* TX Attributes */
+	unsigned int tx_trailingclks;
+	unsigned int tx_dif_p_nsec;
+	unsigned int tx_dif_n_nsec;
+	unsigned int tx_high_z_cnt_nsec;
+	unsigned int tx_base_unit_nsec;
+	unsigned int tx_gran_unit_nsec;
+	unsigned int tx_sleep_cnt;
+	unsigned int tx_min_activatetime;
+	/* RX Attributes */
+	unsigned int rx_filler_enable;
+	unsigned int rx_dif_p_nsec;
+	unsigned int rx_hibern8_wait_nsec;
+	unsigned int rx_base_unit_nsec;
+	unsigned int rx_gran_unit_nsec;
+	unsigned int rx_sleep_cnt;
+	unsigned int rx_stall_cnt;
+	unsigned int rx_hs_g1_sync_len_cap;
+	unsigned int rx_hs_g2_sync_len_cap;
+	unsigned int rx_hs_g3_sync_len_cap;
+	unsigned int rx_hs_g1_prep_sync_len_cap;
+	unsigned int rx_hs_g2_prep_sync_len_cap;
+	unsigned int rx_hs_g3_prep_sync_len_cap;
+	/* Common Attributes */
+	unsigned int cmn_pwm_clk_ctrl;
+	/* Internal Attributes */
+	unsigned int pa_dbg_option_suite;
+	/* Changeable Attributes */
+	unsigned int rx_adv_fine_gran_sup_en;
+	unsigned int rx_adv_fine_gran_step;
+	unsigned int rx_min_actv_time_cap;
+	unsigned int rx_hibern8_time_cap;
+	unsigned int rx_adv_min_actv_time_cap;
+	unsigned int rx_adv_hibern8_time_cap;
+	unsigned int pa_granularity;
+	unsigned int pa_tactivate;
+	unsigned int pa_hibern8time;
+};
+
+struct exynos_ufs_drv_data {
+	char *compatible;
+	struct exynos_ufs_uic_attr *uic_attr;
+	unsigned int quirks;
+	unsigned int opts;
+	/* SoC's specific operations */
+	int (*drv_init)(struct device *dev, struct exynos_ufs *ufs);
+	int (*pre_link)(struct exynos_ufs *ufs);
+	int (*post_link)(struct exynos_ufs *ufs);
+	int (*pre_pwr_change)(struct exynos_ufs *ufs, struct uic_pwr_mode *pwr);
+	int (*post_pwr_change)(struct exynos_ufs *ufs,
+				struct uic_pwr_mode *pwr);
+};
+
+struct ufs_phy_time_cfg {
+	u32 tx_linereset_p;
+	u32 tx_linereset_n;
+	u32 tx_high_z_cnt;
+	u32 tx_base_n_val;
+	u32 tx_gran_n_val;
+	u32 tx_sleep_cnt;
+	u32 rx_linereset;
+	u32 rx_hibern8_wait;
+	u32 rx_base_n_val;
+	u32 rx_gran_n_val;
+	u32 rx_sleep_cnt;
+	u32 rx_stall_cnt;
+};
+
+struct exynos_ufs {
+	struct ufs_hba *hba;
+	struct phy *phy;
+	void __iomem *reg_hci;
+	void __iomem *reg_unipro;
+	void __iomem *reg_ufsp;
+	struct clk *clk_hci_core;
+	struct clk *clk_unipro_main;
+	struct clk *clk_apb;
+	u32 pclk_rate;
+	u32 pclk_div;
+	u32 pclk_avail_min;
+	u32 pclk_avail_max;
+	u32 mclk_rate;
+	int avail_ln_rx;
+	int avail_ln_tx;
+	int rx_sel_idx;
+	struct uic_pwr_mode pwr_req;	/* requested power mode */
+	struct uic_pwr_mode pwr_act;	/* actual power mode */
+	struct ufs_phy_time_cfg t_cfg;
+	ktime_t entry_hibern8_t;
+	struct exynos_ufs_drv_data *drv_data;
+
+	u32 opts;
+#define EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL		BIT(0)
+#define EXYNOS_UFS_OPT_SKIP_CONNECTION_ESTAB	BIT(1)
+#define EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL	BIT(2)
+#define EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX	BIT(3)
+#define EXYNOS_UFS_OPT_USE_SW_HIBERN8_TIMER	BIT(4)
+};
+
+#define for_each_ufs_rx_lane(ufs, i) \
+	for (i = (ufs)->rx_sel_idx; \
+		i < (ufs)->rx_sel_idx + (ufs)->avail_ln_rx; i++)
+#define for_each_ufs_tx_lane(ufs, i) \
+	for (i = 0; i < (ufs)->avail_ln_tx; i++)
+
+#define EXYNOS_UFS_MMIO_FUNC(name)					  \
+static inline void name##_writel(struct exynos_ufs *ufs, u32 val, u32 reg)\
+{									  \
+	writel(val, ufs->reg_##name + reg);				  \
+}									  \
+									  \
+static inline u32 name##_readl(struct exynos_ufs *ufs, u32 reg)		  \
+{									  \
+	return readl(ufs->reg_##name + reg);				  \
+}
+
+EXYNOS_UFS_MMIO_FUNC(hci);
+EXYNOS_UFS_MMIO_FUNC(unipro);
+EXYNOS_UFS_MMIO_FUNC(ufsp);
+#undef EXYNOS_UFS_MMIO_FUNC
+
+extern long exynos_ufs_calc_time_cntr(struct exynos_ufs *, long);
+
+static inline void exynos_ufs_enable_ov_tm(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OV_TM), TRUE);
+}
+
+static inline void exynos_ufs_disable_ov_tm(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OV_TM), FALSE);
+}
+
+static inline void exynos_ufs_enable_dbg_mode(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_MODE), TRUE);
+}
+
+static inline void exynos_ufs_disable_dbg_mode(struct ufs_hba *hba)
+{
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_MODE), FALSE);
+}
+
+struct exynos_ufs_drv_data exynos_ufs_drvs;
+
+struct exynos_ufs_uic_attr exynos7_uic_attr = {
+	.tx_trailingclks		= 0x10,
+	.tx_dif_p_nsec			= 3000000,	/* unit: ns */
+	.tx_dif_n_nsec			= 1000000,	/* unit: ns */
+	.tx_high_z_cnt_nsec		= 20000,	/* unit: ns */
+	.tx_base_unit_nsec		= 100000,	/* unit: ns */
+	.tx_gran_unit_nsec		= 4000,		/* unit: ns */
+	.tx_sleep_cnt			= 1000,		/* unit: ns */
+	.tx_min_activatetime		= 0xa,
+	.rx_filler_enable		= 0x2,
+	.rx_dif_p_nsec			= 1000000,	/* unit: ns */
+	.rx_hibern8_wait_nsec		= 4000000,	/* unit: ns */
+	.rx_base_unit_nsec		= 100000,	/* unit: ns */
+	.rx_gran_unit_nsec		= 4000,		/* unit: ns */
+	.rx_sleep_cnt			= 1280,		/* unit: ns */
+	.rx_stall_cnt			= 320,		/* unit: ns */
+	.rx_hs_g1_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g2_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g3_sync_len_cap		= SYNC_LEN_COARSE(0xf),
+	.rx_hs_g1_prep_sync_len_cap	= PREP_LEN(0xf),
+	.rx_hs_g2_prep_sync_len_cap	= PREP_LEN(0xf),
+	.rx_hs_g3_prep_sync_len_cap	= PREP_LEN(0xf),
+	.pa_dbg_option_suite		= 0x30103,
+};
+#endif /* _UFS_EXYNOS_H_ */
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
index 3dc4d8b76509..f441ab54829c 100644
--- a/drivers/scsi/ufs/unipro.h
+++ b/drivers/scsi/ufs/unipro.h
@@ -64,8 +64,25 @@
 #define CFGRXOVR4				0x00E9
 #define RXSQCTRL				0x00B5
 #define CFGRXOVR6				0x00BF
+#define RX_HS_G1_SYNC_LENGTH_CAP		0x008B
+#define RX_HS_G1_PREP_LENGTH_CAP		0x008C
+#define RX_HS_G2_SYNC_LENGTH_CAP		0x0094
+#define RX_HS_G3_SYNC_LENGTH_CAP		0x0095
+#define RX_HS_G2_PREP_LENGTH_CAP		0x0096
+#define RX_HS_G3_PREP_LENGTH_CAP		0x0097
+#define RX_ADV_GRANULARITY_CAP			0x0098
+#define RX_MIN_ACTIVATETIME_CAP			0x008F
+#define RX_HIBERN8TIME_CAP			0x0092
+#define RX_ADV_HIBERN8TIME_CAP			0x0099
+#define RX_ADV_MIN_ACTIVATETIME_CAP		0x009A
+
 
 #define is_mphy_tx_attr(attr)			(attr < RX_MODE)
+#define RX_ADV_FINE_GRAN_STEP(x)		((((x) & 0x3) << 1) | 0x1)
+#define SYNC_LEN_FINE(x)			((x) & 0x3F)
+#define SYNC_LEN_COARSE(x)			((1 << 6) | ((x) & 0x3F))
+#define PREP_LEN(x)				((x) & 0xF)
+
 #define RX_MIN_ACTIVATETIME_UNIT_US		100
 #define HIBERN8TIME_UNIT_US			100
 
@@ -124,6 +141,7 @@
 #define PA_PACPREQEOBTIMEOUT	0x1591
 #define PA_HIBERN8TIME		0x15A7
 #define PA_LOCALVERINFO		0x15A9
+#define PA_GRANULARITY		0x15AA
 #define PA_TACTIVATE		0x15A8
 #define PA_PACPFRAMECOUNT	0x15C0
 #define PA_PACPERRORCOUNT	0x15C1
@@ -181,6 +199,9 @@ enum {
 	UNCHANGED	= 7,
 };
 
+#define IS_UFS_PWR_MODE_HS(m)	(((m) == FAST_MODE) || ((m) == FASTAUTO_MODE))
+#define IS_UFS_PWR_MODE_PWM(m)	(((m) == SLOW_MODE) || ((m) == SLOWAUTO_MODE))
+
 /* PA TX/RX Frequency Series */
 enum {
 	PA_HS_MODE_A	= 1,
@@ -242,6 +263,11 @@ enum ufs_unipro_ver {
 #define DL_PEERTC1PRESENT	0x2066
 #define DL_PEERTC1RXINITCREVAL	0x2067
 
+/* Default value of L2 Timer */
+#define FC0PROTTIMEOUTVAL	8191
+#define TC0REPLAYTIMEOUTVAL	65535
+#define AFC0REQTIMEOUTVAL	32767
+
 /*
  * Network Layer Attributes
  */
@@ -284,4 +310,19 @@ enum {
 	TRUE,
 };
 
+/* CPort setting */
+#define E2EFC_ON	(1 << 0)
+#define E2EFC_OFF	(0 << 0)
+#define CSD_N_ON	(0 << 1)
+#define CSD_N_OFF	(1 << 1)
+#define CSV_N_ON	(0 << 2)
+#define CSV_N_OFF	(1 << 2)
+#define CPORT_DEF_FLAGS	(CSV_N_OFF | CSD_N_OFF | E2EFC_OFF)
+
+/* CPort connection state */
+enum {
+	CPORT_IDLE = 0,
+	CPORT_CONNECTED,
+};
+
 #endif /* _UNIPRO_H_ */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v3 5/5] arm64: dts: Add node for ufs exynos7

[Alim Akhtar]

Adding dt node foe UFS and UFS-PHY for exynos7 SoC.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../boot/dts/exynos/exynos7-espresso.dts      | 16 +++++++
 arch/arm64/boot/dts/exynos/exynos7.dtsi       | 43 ++++++++++++++++++-
 2 files changed, 57 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
index 7af288fa9475..b59a0a32620a 100644
--- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
+++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
@@ -406,6 +406,22 @@
 	};
 };
 
+&ufs {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ufs_rst_n &ufs_refclk_out>;
+	ufs,pwr-attr-mode = "FAST";
+	ufs,pwr-attr-lane = <2>;
+	ufs,pwr-attr-gear = <2>;
+	ufs,pwr-attr-hs-series = "HS_rate_b";
+	ufs-rx-adv-fine-gran-sup_en = <1>;
+	ufs-rx-adv-fine-gran-step = <3>;
+	ufs-rx-adv-min-activate-time-cap = <9>;
+	ufs-pa-granularity = <6>;
+	ufs-pa-tacctivate = <3>;
+	ufs-pa-hibern8time = <20>;
+};
+
 &usbdrd_phy {
 	vbus-supply = <&usb30_vbus_reg>;
 	vbus-boost-supply = <&usb3drd_boost_5v>;
diff --git a/arch/arm64/boot/dts/exynos/exynos7.dtsi b/arch/arm64/boot/dts/exynos/exynos7.dtsi
index 5558045637ac..9d16c90edd07 100644
--- a/arch/arm64/boot/dts/exynos/exynos7.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7.dtsi
@@ -220,9 +220,14 @@
 			#clock-cells = <1>;
 			clocks = <&fin_pll>, <&clock_top1 DOUT_ACLK_FSYS1_200>,
 				 <&clock_top1 DOUT_SCLK_MMC0>,
-				 <&clock_top1 DOUT_SCLK_MMC1>;
+				 <&clock_top1 DOUT_SCLK_MMC1>,
+				 <&clock_top1 DOUT_SCLK_UFSUNIPRO20>,
+				 <&clock_top1 DOUT_SCLK_PHY_FSYS1>,
+				 <&clock_top1 DOUT_SCLK_PHY_FSYS1_26M>;
 			clock-names = "fin_pll", "dout_aclk_fsys1_200",
-				      "dout_sclk_mmc0", "dout_sclk_mmc1";
+				      "dout_sclk_mmc0", "dout_sclk_mmc1",
+				      "dout_sclk_ufsunipro20", "dout_sclk_phy_fsys1",
+				      "dout_sclk_phy_fsys1_26m";
 		};
 
 		serial_0: serial@13630000 {
@@ -601,6 +606,40 @@
 			};
 		};
 
+		ufs: ufs@15570000 {
+			compatible = "samsung,exynos7-ufs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			reg = <0x15570000 0x100>,  /* 0: HCI standard */
+				<0x15570100 0x100>,  /* 1: Vendor specificed */
+				<0x15571000 0x200>,  /* 2: UNIPRO */
+				<0x15572000 0x300>;  /* 3: UFS protector */
+			reg-names = "hci", "vs_hci", "unipro", "ufsp";
+			interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock_fsys1 ACLK_UFS20_LINK>,
+				<&clock_fsys1 SCLK_UFSUNIPRO20_USER>;
+			clock-names = "core_clk", "sclk_unipro_main";
+			freq-table-hz = <0 0>, <0 0>;
+			pclk-freq-avail-range = <70000000 133000000>;
+			ufs,pwr-local-l2-timer = <8000 28000 20000>;
+			ufs,pwr-remote-l2-timer = <12000 32000 16000>;
+			phys = <&ufs_phy>;
+			phy-names = "ufs-phy";
+			status = "disabled";
+		};
+
+		ufs_phy: ufs-phy@0x15571800 {
+			compatible = "samsung,exynos7-ufs-phy";
+			reg = <0x15571800 0x240>;
+			reg-names = "phy-pma";
+			samsung,pmu-syscon = <&pmu_system_controller>;
+			#phy-cells = <0>;
+			clocks = <&clock_fsys1 MOUT_FSYS1_PHYCLK_SEL1>,
+				<&clock_top1 CLK_SCLK_PHY_FSYS1_26M>;
+			clock-names = "ref_clk_parent", "ref_clk";
+		};
+
 		usbdrd_phy: phy@15500000 {
 			compatible = "samsung,exynos7-usbdrd-phy";
 			reg = <0x15500000 0x100>;
-- 
2.17.1

[PATCH v3 5/5] arm64: dts: Add node for ufs exynos7

[Alim Akhtar]

Adding dt node foe UFS and UFS-PHY for exynos7 SoC.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
---
 .../boot/dts/exynos/exynos7-espresso.dts      | 16 +++++++
 arch/arm64/boot/dts/exynos/exynos7.dtsi       | 43 ++++++++++++++++++-
 2 files changed, 57 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
index 7af288fa9475..b59a0a32620a 100644
--- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
+++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
@@ -406,6 +406,22 @@
 	};
 };
 
+&ufs {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ufs_rst_n &ufs_refclk_out>;
+	ufs,pwr-attr-mode = "FAST";
+	ufs,pwr-attr-lane = <2>;
+	ufs,pwr-attr-gear = <2>;
+	ufs,pwr-attr-hs-series = "HS_rate_b";
+	ufs-rx-adv-fine-gran-sup_en = <1>;
+	ufs-rx-adv-fine-gran-step = <3>;
+	ufs-rx-adv-min-activate-time-cap = <9>;
+	ufs-pa-granularity = <6>;
+	ufs-pa-tacctivate = <3>;
+	ufs-pa-hibern8time = <20>;
+};
+
 &usbdrd_phy {
 	vbus-supply = <&usb30_vbus_reg>;
 	vbus-boost-supply = <&usb3drd_boost_5v>;
diff --git a/arch/arm64/boot/dts/exynos/exynos7.dtsi b/arch/arm64/boot/dts/exynos/exynos7.dtsi
index 5558045637ac..9d16c90edd07 100644
--- a/arch/arm64/boot/dts/exynos/exynos7.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7.dtsi
@@ -220,9 +220,14 @@
 			#clock-cells = <1>;
 			clocks = <&fin_pll>, <&clock_top1 DOUT_ACLK_FSYS1_200>,
 				 <&clock_top1 DOUT_SCLK_MMC0>,
-				 <&clock_top1 DOUT_SCLK_MMC1>;
+				 <&clock_top1 DOUT_SCLK_MMC1>,
+				 <&clock_top1 DOUT_SCLK_UFSUNIPRO20>,
+				 <&clock_top1 DOUT_SCLK_PHY_FSYS1>,
+				 <&clock_top1 DOUT_SCLK_PHY_FSYS1_26M>;
 			clock-names = "fin_pll", "dout_aclk_fsys1_200",
-				      "dout_sclk_mmc0", "dout_sclk_mmc1";
+				      "dout_sclk_mmc0", "dout_sclk_mmc1",
+				      "dout_sclk_ufsunipro20", "dout_sclk_phy_fsys1",
+				      "dout_sclk_phy_fsys1_26m";
 		};
 
 		serial_0: serial@13630000 {
@@ -601,6 +606,40 @@
 			};
 		};
 
+		ufs: ufs@15570000 {
+			compatible = "samsung,exynos7-ufs";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			reg = <0x15570000 0x100>,  /* 0: HCI standard */
+				<0x15570100 0x100>,  /* 1: Vendor specificed */
+				<0x15571000 0x200>,  /* 2: UNIPRO */
+				<0x15572000 0x300>;  /* 3: UFS protector */
+			reg-names = "hci", "vs_hci", "unipro", "ufsp";
+			interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock_fsys1 ACLK_UFS20_LINK>,
+				<&clock_fsys1 SCLK_UFSUNIPRO20_USER>;
+			clock-names = "core_clk", "sclk_unipro_main";
+			freq-table-hz = <0 0>, <0 0>;
+			pclk-freq-avail-range = <70000000 133000000>;
+			ufs,pwr-local-l2-timer = <8000 28000 20000>;
+			ufs,pwr-remote-l2-timer = <12000 32000 16000>;
+			phys = <&ufs_phy>;
+			phy-names = "ufs-phy";
+			status = "disabled";
+		};
+
+		ufs_phy: ufs-phy@0x15571800 {
+			compatible = "samsung,exynos7-ufs-phy";
+			reg = <0x15571800 0x240>;
+			reg-names = "phy-pma";
+			samsung,pmu-syscon = <&pmu_system_controller>;
+			#phy-cells = <0>;
+			clocks = <&clock_fsys1 MOUT_FSYS1_PHYCLK_SEL1>,
+				<&clock_top1 CLK_SCLK_PHY_FSYS1_26M>;
+			clock-names = "ref_clk_parent", "ref_clk";
+		};
+
 		usbdrd_phy: phy@15500000 {
 			compatible = "samsung,exynos7-usbdrd-phy";
 			reg = <0x15500000 0x100>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Paweł Chmiel]

On Thu, 2020-03-19 at 20:30 +0530, Alim Akhtar wrote:
> This patch-set introduces UFS (Universal Flash Storage) host controller support
> for Samsung family SoC. Mostly, it consists of UFS PHY and host specific driver.
> 
> - Changes since v2:
> * fixed build warning by kbuild test robot 
> * Added Reported-by tags
> 
> - Changes since v1:
> * fixed make dt_binding_check error as pointed by Rob
> * Addressed Krzysztof's review comments
> * Added Reviewed-by tags
> 
>  
> patch 1/5: define devicetree bindings for UFS PHY
> patch 2/5: Adds UFS PHY driver
> patch 3/5: define devicetree bindings for UFS HCI 
> patch 4/5: Adds Samsung UFS HCI driver
> patch 5/5: Enabled UFS on exynos7 platform
Hi
Is this compatible with Exynos7420? Looking at u-boot source code,
there is Espresso7420 - isn't it the same device? Also this driver
looks very similar to the one from vendor kernel sources (for my
device). 

I did tried to run this on my Exynos7420 based device (Samsung S6 Edge
phone) with 5.6-rc6, to get any storage working (since it doesn't have sdcard slot).

At first i got error in exynos_ufs_config_smu. Looking at vendor
sources, on my device only secureos is able to write to those registers
so i fixed it by using smc calls and driver probes fine. Will this be
also supported by driver (maybe in future)?

But now got another error
[    1.610464] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.610629] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.610747] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.610863] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.614727] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.621061] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.627396] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.633730] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.640065] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.646400] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.652734] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    1.747649] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.747807] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.747924] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.748041] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.751909] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.758244] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.764578] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.770913] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.777248] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.783582] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.789917] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    1.884841] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.884999] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.885116] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.885233] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.889100] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.895435] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.901770] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.908104] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.914439] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.920773] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.927108] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    2.998155] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    4.502138] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    6.006137] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    6.006311] exynos-ufshc 15570000.ufs: ufshcd_query_flag_retry:
query attribute, opcode 5, idn 1, failed with error -11 after 3 retires
[    6.006545] exynos-ufshc 15570000.ufs: ufshcd_complete_dev_init
reading fDeviceInit flag failed with error -11

Do You have any idea what could be wrong?

Thanks
> 
> Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)
> 
> 
> Alim Akhtar (5):
>   dt-bindings: phy: Document Samsung UFS PHY bindings
>   phy: samsung-ufs: add UFS PHY driver for samsung SoC
>   Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
>     controller
>   scsi: ufs-exynos: add UFS host support for Exynos SoCs
>   arm64: dts: Add node for ufs exynos7
> 
>  .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
>  .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
>  .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
>  arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
>  drivers/phy/samsung/Kconfig                   |    9 +
>  drivers/phy/samsung/Makefile                  |    1 +
>  drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
>  drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
>  drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
>  drivers/scsi/ufs/Kconfig                      |   12 +
>  drivers/scsi/ufs/Makefile                     |    1 +
>  drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
>  drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
>  drivers/scsi/ufs/unipro.h                     |   41 +
>  include/linux/phy/phy-samsung-ufs.h           |   70 +
>  15 files changed, 2521 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
>  create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt
>  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
>  create mode 100644 drivers/scsi/ufs/ufs-exynos.c
>  create mode 100644 drivers/scsi/ufs/ufs-exynos.h
>  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> 

Re: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Paweł Chmiel]

On Thu, 2020-03-19 at 20:30 +0530, Alim Akhtar wrote:
> This patch-set introduces UFS (Universal Flash Storage) host controller support
> for Samsung family SoC. Mostly, it consists of UFS PHY and host specific driver.
> 
> - Changes since v2:
> * fixed build warning by kbuild test robot 
> * Added Reported-by tags
> 
> - Changes since v1:
> * fixed make dt_binding_check error as pointed by Rob
> * Addressed Krzysztof's review comments
> * Added Reviewed-by tags
> 
>  
> patch 1/5: define devicetree bindings for UFS PHY
> patch 2/5: Adds UFS PHY driver
> patch 3/5: define devicetree bindings for UFS HCI 
> patch 4/5: Adds Samsung UFS HCI driver
> patch 5/5: Enabled UFS on exynos7 platform
Hi
Is this compatible with Exynos7420? Looking at u-boot source code,
there is Espresso7420 - isn't it the same device? Also this driver
looks very similar to the one from vendor kernel sources (for my
device). 

I did tried to run this on my Exynos7420 based device (Samsung S6 Edge
phone) with 5.6-rc6, to get any storage working (since it doesn't have sdcard slot).

At first i got error in exynos_ufs_config_smu. Looking at vendor
sources, on my device only secureos is able to write to those registers
so i fixed it by using smc calls and driver probes fine. Will this be
also supported by driver (maybe in future)?

But now got another error
[    1.610464] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.610629] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.610747] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.610863] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.614727] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.621061] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.627396] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.633730] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.640065] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.646400] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.652734] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    1.747649] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.747807] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.747924] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.748041] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.751909] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.758244] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.764578] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.770913] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.777248] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.783582] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.789917] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    1.884841] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
interrupt 0x00000000
[    1.884999] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
[    1.885116] host_regs: 00000010: 00000101 00007fce 00000000 00000000
[    1.885233] host_regs: 00000020: 00000000 00030e75 00000000 00000000
[    1.889100] host_regs: 00000030: 0000000f 00000000 00000000 00000000
[    1.895435] host_regs: 00000040: 00000000 00000000 00000000 00000000
[    1.901770] host_regs: 00000050: f8c37000 00000000 00000001 00000000
[    1.908104] host_regs: 00000060: 00000001 00000000 00000000 00000000
[    1.914439] host_regs: 00000070: f9644000 00000000 00000000 00000000
[    1.920773] host_regs: 00000080: 00000001 00000000 00000000 00000000
[    1.927108] host_regs: 00000090: 00000002 95290000 00000000 00000000
[    2.998155] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    4.502138] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    6.006137] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
flag query for idn 1 failed, err = -11
[    6.006311] exynos-ufshc 15570000.ufs: ufshcd_query_flag_retry:
query attribute, opcode 5, idn 1, failed with error -11 after 3 retires
[    6.006545] exynos-ufshc 15570000.ufs: ufshcd_complete_dev_init
reading fDeviceInit flag failed with error -11

Do You have any idea what could be wrong?

Thanks
> 
> Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)
> 
> 
> Alim Akhtar (5):
>   dt-bindings: phy: Document Samsung UFS PHY bindings
>   phy: samsung-ufs: add UFS PHY driver for samsung SoC
>   Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
>     controller
>   scsi: ufs-exynos: add UFS host support for Exynos SoCs
>   arm64: dts: Add node for ufs exynos7
> 
>  .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
>  .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
>  .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
>  arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
>  drivers/phy/samsung/Kconfig                   |    9 +
>  drivers/phy/samsung/Makefile                  |    1 +
>  drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
>  drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
>  drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
>  drivers/scsi/ufs/Kconfig                      |   12 +
>  drivers/scsi/ufs/Makefile                     |    1 +
>  drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
>  drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
>  drivers/scsi/ufs/unipro.h                     |   41 +
>  include/linux/phy/phy-samsung-ufs.h           |   70 +
>  15 files changed, 2521 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
>  create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt
>  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
>  create mode 100644 drivers/scsi/ufs/ufs-exynos.c
>  create mode 100644 drivers/scsi/ufs/ufs-exynos.h
>  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Rob Herring]

On Thu, 19 Mar 2020 20:30:27 +0530, Alim Akhtar wrote:
> This patch documents Samsung UFS PHY device tree bindings
> 
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
>  1 file changed, 62 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml: example-0: 'ufs-phy@0x15571800' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'

See https://patchwork.ozlabs.org/patch/1258280

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:

pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade

Please check and re-submit.

Re: [PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Rob Herring]

On Thu, 19 Mar 2020 20:30:27 +0530, Alim Akhtar wrote:
> This patch documents Samsung UFS PHY device tree bindings
> 
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> ---
>  .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
>  1 file changed, 62 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> 

My bot found errors running 'make dt_binding_check' on your patch:

/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml: example-0: 'ufs-phy@0x15571800' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'

See https://patchwork.ozlabs.org/patch/1258280

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:

pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade

Please check and re-submit.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Alim Akhtar]

Hi Rob

On Fri, Mar 20, 2020 at 5:53 AM Rob Herring <robh@kernel.org> wrote:
>
> On Thu, 19 Mar 2020 20:30:27 +0530, Alim Akhtar wrote:
> > This patch documents Samsung UFS PHY device tree bindings
> >
> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> > ---
> >  .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> >
>
> My bot found errors running 'make dt_binding_check' on your patch:
>
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml: example-0: 'ufs-phy@0x15571800' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
>
> See https://patchwork.ozlabs.org/patch/1258280
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure dt-schema is up to date:
>
Yes, I did ran 'make dt_binding_check' and saw no errors,

---
/work/linux $ make dt_binding_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
scripts/kconfig/conf  --syncconfig Kconfig
  HOSTCC  scripts/dtc/dtc.o
  HOSTCC  scripts/dtc/flattree.o
  HOSTCC  scripts/dtc/fstree.o
  HOSTCC  scripts/dtc/data.o
  HOSTCC  scripts/dtc/livetree.o
  HOSTCC  scripts/dtc/treesource.o
  HOSTCC  scripts/dtc/srcpos.o
  HOSTCC  scripts/dtc/checks.o
  HOSTCC  scripts/dtc/util.o
  LEX     scripts/dtc/dtc-lexer.lex.c
  YACC    scripts/dtc/dtc-parser.tab.[ch]
  HOSTCC  scripts/dtc/dtc-lexer.lex.o
  HOSTCC  scripts/dtc/dtc-parser.tab.o
  HOSTCC  scripts/dtc/yamltree.o
  HOSTLD  scripts/dtc/dtc
  CHKDT   Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
  SCHEMA  Documentation/devicetree/bindings/processed-schema.yaml
  DTC     Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml
  CHECK   Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml
~/work/linux $ dtc --version
Version: DTC 1.5.0-g62cb4ad2
---------------
> pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
>
Thanks for pointing this out, I will upgrade and re-run and re-submit.

> Please check and re-submit.



-- 
Regards,
Alim

Re: [PATCH v3 1/5] dt-bindings: phy: Document Samsung UFS PHY bindings

[Alim Akhtar]

Hi Rob

On Fri, Mar 20, 2020 at 5:53 AM Rob Herring <robh@kernel.org> wrote:
>
> On Thu, 19 Mar 2020 20:30:27 +0530, Alim Akhtar wrote:
> > This patch documents Samsung UFS PHY device tree bindings
> >
> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> > ---
> >  .../bindings/phy/samsung,ufs-phy.yaml         | 62 +++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> >
>
> My bot found errors running 'make dt_binding_check' on your patch:
>
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml: example-0: 'ufs-phy@0x15571800' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
>
> See https://patchwork.ozlabs.org/patch/1258280
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure dt-schema is up to date:
>
Yes, I did ran 'make dt_binding_check' and saw no errors,

---
/work/linux $ make dt_binding_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
scripts/kconfig/conf  --syncconfig Kconfig
  HOSTCC  scripts/dtc/dtc.o
  HOSTCC  scripts/dtc/flattree.o
  HOSTCC  scripts/dtc/fstree.o
  HOSTCC  scripts/dtc/data.o
  HOSTCC  scripts/dtc/livetree.o
  HOSTCC  scripts/dtc/treesource.o
  HOSTCC  scripts/dtc/srcpos.o
  HOSTCC  scripts/dtc/checks.o
  HOSTCC  scripts/dtc/util.o
  LEX     scripts/dtc/dtc-lexer.lex.c
  YACC    scripts/dtc/dtc-parser.tab.[ch]
  HOSTCC  scripts/dtc/dtc-lexer.lex.o
  HOSTCC  scripts/dtc/dtc-parser.tab.o
  HOSTCC  scripts/dtc/yamltree.o
  HOSTLD  scripts/dtc/dtc
  CHKDT   Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
  SCHEMA  Documentation/devicetree/bindings/processed-schema.yaml
  DTC     Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml
  CHECK   Documentation/devicetree/bindings/phy/samsung,ufs-phy.example.dt.yaml
~/work/linux $ dtc --version
Version: DTC 1.5.0-g62cb4ad2
---------------
> pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
>
Thanks for pointing this out, I will upgrade and re-run and re-submit.

> Please check and re-submit.



-- 
Regards,
Alim

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Kishon Vijay Abraham I]

Hi Alim,

On 3/19/2020 8:30 PM, Alim Akhtar wrote:
> This patch introduces Samsung UFS PHY driver. This driver
> supports to deal with phy calibration and power control
> according to UFS host driver's behavior.
> 
> Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  drivers/phy/samsung/Kconfig           |   9 +
>  drivers/phy/samsung/Makefile          |   1 +
>  drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
>  drivers/phy/samsung/phy-samsung-ufs.c | 311 ++++++++++++++++++++++++++
>  drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
>  include/linux/phy/phy-samsung-ufs.h   |  70 ++++++

Why is this added in include directory? will it be used by controller driver?

Thanks
Kishon
>  6 files changed, 576 insertions(+)
>  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
>  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> 
> diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
> index 9e483d1fdaf2..fc1e3c17f842 100644
> --- a/drivers/phy/samsung/Kconfig
> +++ b/drivers/phy/samsung/Kconfig
> @@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
>  	  Enable PCIe PHY support for Exynos SoC series.
>  	  This driver provides PHY interface for Exynos PCIe controller.
>  
> +config PHY_SAMSUNG_UFS
> +	tristate "SAMSUNG SoC series UFS PHY driver"
> +	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Samsung UFS PHY driver for
> +	  Samsung SoCs. This driver provides the interface for UFS
> +	  host controller to do PHY related programming.
> +
>  config PHY_SAMSUNG_USB2
>  	tristate "Samsung USB 2.0 PHY driver"
>  	depends on HAS_IOMEM
> diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
> index db9b1aa0de6e..3959100fe8a2 100644
> --- a/drivers/phy/samsung/Makefile
> +++ b/drivers/phy/samsung/Makefile
> @@ -2,6 +2,7 @@
>  obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
>  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
>  obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
> +obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
>  phy-exynos-usb2-y			+= phy-samsung-usb2.o
>  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
> diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h b/drivers/phy/samsung/phy-exynos7-ufs.h
> new file mode 100644
> index 000000000000..da981c1ac040
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-exynos7-ufs.h
> @@ -0,0 +1,85 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * UFS PHY driver data for Samsung EXYNOS7 SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + */
> +#ifndef _PHY_EXYNOS7_UFS_H_
> +#define _PHY_EXYNOS7_UFS_H_
> +
> +#include "phy-samsung-ufs.h"
> +
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
> +
> +/* Calibration for phy initialization */
> +static const struct samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
> +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
> +	END_UFS_PHY_CFG
> +};
> +
> +static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
> +	END_UFS_PHY_CFG
> +};
> +
> +/* Calibration for HS mode series A/B */
> +static const struct samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
> +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
> +	/* Setting order: 1st(0x16, 2nd(0x15) */
> +	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
> +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
> +	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
> +	END_UFS_PHY_CFG
> +};
> +
> +/* Calibration for HS mode series A/B atfer PMC */
> +static const struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
> +	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
> +	END_UFS_PHY_CFG
> +};
> +
> +static const struct samsung_ufs_phy_cfg *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
> +	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
> +	[CFG_POST_INIT]		= exynos7_post_init_cfg,
> +	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
> +	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
> +};
> +
> +static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
> +	.cfg = exynos7_ufs_phy_cfgs,
> +	.isol = {
> +		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
> +		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
> +		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
> +	},
> +};
> +
> +#endif /* _PHY_EXYNOS7_UFS_H_ */
> diff --git a/drivers/phy/samsung/phy-samsung-ufs.c b/drivers/phy/samsung/phy-samsung-ufs.c
> new file mode 100644
> index 000000000000..2d5db24de49b
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-samsung-ufs.c
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * UFS PHY driver for Samsung SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/phy/phy-samsung-ufs.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include "phy-samsung-ufs.h"
> +
> +#define for_each_phy_lane(phy, i) \
> +	for (i = 0; i < (phy)->lane_cnt; i++)
> +#define for_each_phy_cfg(cfg) \
> +	for (; (cfg)->id; (cfg)++)
> +
> +#define PHY_DEF_LANE_CNT	1
> +
> +static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
> +			const struct samsung_ufs_phy_cfg *cfg, u8 lane)
> +{
> +	enum {LANE_0, LANE_1}; /* lane index */
> +
> +	switch (lane) {
> +	case LANE_0:
> +		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
> +		break;
> +	case LANE_1:
> +		if (cfg->id == PHY_TRSV_BLK)
> +			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
> +		break;
> +	}
> +}
> +
> +int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> +	const unsigned int timeout_us = 100000;
> +	const unsigned int sleep_us = 10;
> +	u32 val;
> +	int err;
> +
> +	err = readl_poll_timeout(
> +			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
> +			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
> +	if (err) {
> +		dev_err(ufs_phy->dev,
> +			"failed to get phy pll lock acquisition %d\n", err);
> +		goto out;
> +	}
> +
> +	err = readl_poll_timeout(
> +			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
> +			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
> +	if (err) {
> +		dev_err(ufs_phy->dev,
> +			"failed to get phy cdr lock acquisition %d\n", err);
> +		goto out;
> +	}
> +
> +out:
> +	return err;
> +}
> +
> +int samsung_ufs_phy_calibrate(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> +	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
> +	const struct samsung_ufs_phy_cfg *cfg;
> +	int i;
> +	int err = 0;
> +
> +	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
> +		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
> +		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
> +							ufs_phy->ufs_phy_state);
> +		return -EINVAL;
> +	}
> +
> +	if (ufs_phy->is_pre_init)
> +		ufs_phy->is_pre_init = false;
> +	if (ufs_phy->is_post_init) {
> +		ufs_phy->is_post_init = false;
> +		ufs_phy->ufs_phy_state = CFG_POST_INIT;
> +	}
> +	if (ufs_phy->is_pre_pmc) {
> +		ufs_phy->is_pre_pmc = false;
> +		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
> +	}
> +	if (ufs_phy->is_post_pmc) {
> +		ufs_phy->is_post_pmc = false;
> +		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
> +	}
> +
> +	switch (ufs_phy->ufs_phy_state) {
> +	case CFG_PRE_INIT:
> +		ufs_phy->is_post_init = true;
> +		break;
> +	case CFG_POST_INIT:
> +		ufs_phy->is_pre_pmc = true;
> +		break;
> +	case CFG_PRE_PWR_HS:
> +		ufs_phy->is_post_pmc = true;
> +		break;
> +	case CFG_POST_PWR_HS:
> +		break;
> +	default:
> +		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
> +	}
> +
> +	cfg = cfgs[ufs_phy->ufs_phy_state];
> +	if (!cfg)
> +		goto out;
> +
> +	for_each_phy_cfg(cfg) {
> +		for_each_phy_lane(ufs_phy, i) {
> +			samsung_ufs_phy_config(ufs_phy, cfg, i);
> +		}
> +	}
> +
> +	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
> +		err = samsung_ufs_phy_wait_for_lock_acq(phy);
> +out:
> +	return err;
> +}
> +
> +static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy)
> +{
> +	struct clk *child, *parent;
> +
> +	child = devm_clk_get(phy->dev, "ref_clk");
> +	if (IS_ERR(child))
> +		dev_err(phy->dev, "failed to get ref_clk clock\n");
> +	else
> +		phy->ref_clk = child;
> +
> +	parent = devm_clk_get(phy->dev, "ref_clk_parent");
> +	if (IS_ERR(parent))
> +		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
> +	else
> +		phy->ref_clk_parent = parent;
> +
> +	return clk_set_parent(child, parent);
> +}
> +
> +static int samsung_ufs_phy_init(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +
> +	_phy->lane_cnt = phy->attrs.bus_width;
> +	_phy->ufs_phy_state = CFG_PRE_INIT;
> +
> +	_phy->is_pre_init = true;
> +	_phy->is_post_init = false;
> +	_phy->is_pre_pmc = false;
> +	_phy->is_post_pmc = false;
> +
> +	samsung_ufs_phy_clks_init(_phy);
> +
> +	samsung_ufs_phy_calibrate(phy);
> +
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_power_on(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +	int ret;
> +
> +	ret = clk_prepare_enable(_phy->ref_clk);
> +	if (ret) {
> +		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
> +				__func__, ret);
> +		return ret;
> +	}
> +
> +	samsung_ufs_phy_ctrl_isol(_phy, false);
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_power_off(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +
> +	samsung_ufs_phy_ctrl_isol(_phy, true);
> +	clk_disable_unprepare(_phy->ref_clk);
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
> +					enum phy_mode mode, int submode)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
> +
> +	_phy->mode = PHY_MODE_INVALID;
> +
> +	if (mode > 0)
> +		_phy->mode = mode;
> +
> +	return 0;
> +}
> +
> +static struct phy_ops samsung_ufs_phy_ops = {
> +	.init		= samsung_ufs_phy_init,
> +	.power_on	= samsung_ufs_phy_power_on,
> +	.power_off	= samsung_ufs_phy_power_off,
> +	.calibrate	= samsung_ufs_phy_calibrate,
> +	.set_mode	= samsung_ufs_phy_set_mode,
> +}
> +;
> +static const struct of_device_id samsung_ufs_phy_match[];
> +
> +static int samsung_ufs_phy_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	const struct of_device_id *match;
> +	struct samsung_ufs_phy *phy;
> +	struct phy *gen_phy;
> +	struct phy_provider *phy_provider;
> +	const struct samsung_ufs_phy_drvdata *drvdata;
> +	int err = 0;
> +
> +	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
> +	if (!match) {
> +		err = -EINVAL;
> +		dev_err(dev, "failed to get match_node\n");
> +		goto out;
> +	}
> +
> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy) {
> +		err = -ENOMEM;
> +		goto out;
> +	}
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-pma");
> +	phy->reg_pma = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(phy->reg_pma)) {
> +		err = PTR_ERR(phy->reg_pma);
> +		goto out;
> +	}
> +
> +	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
> +				dev->of_node, "samsung,pmu-syscon");
> +	if (IS_ERR(phy->reg_pmu)) {
> +		err = PTR_ERR(phy->reg_pmu);
> +		dev_err(dev, "failed syscon remap for pmu\n");
> +		goto out;
> +	}
> +
> +	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
> +	if (IS_ERR(gen_phy)) {
> +		err = PTR_ERR(gen_phy);
> +		dev_err(dev, "failed to create PHY for ufs-phy\n");
> +		goto out;
> +	}
> +
> +	drvdata = match->data;
> +	phy->dev = dev;
> +	phy->drvdata = drvdata;
> +	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
> +	phy->isol = &drvdata->isol;
> +	phy->lane_cnt = PHY_DEF_LANE_CNT;
> +
> +	phy_set_drvdata(gen_phy, phy);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider)) {
> +		err = PTR_ERR(phy_provider);
> +		dev_err(dev, "failed to register phy-provider\n");
> +		goto out;
> +	}
> +out:
> +	return err;
> +}
> +
> +static const struct of_device_id samsung_ufs_phy_match[] = {
> +	{
> +		.compatible = "samsung,exynos7-ufs-phy",
> +		.data = &exynos7_ufs_phy,
> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
> +
> +static struct platform_driver samsung_ufs_phy_driver = {
> +	.probe  = samsung_ufs_phy_probe,
> +	.driver = {
> +		.name = "samsung-ufs-phy",
> +		.of_match_table = samsung_ufs_phy_match,
> +	},
> +};
> +module_platform_driver(samsung_ufs_phy_driver);
> +MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
> +MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
> +MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/phy/samsung/phy-samsung-ufs.h b/drivers/phy/samsung/phy-samsung-ufs.h
> new file mode 100644
> index 000000000000..d0ae2b416b2b
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-samsung-ufs.h
> @@ -0,0 +1,100 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * UFS PHY driver for Samsung EXYNOS SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +#ifndef _PHY_SAMSUNG_UFS_
> +#define _PHY_SAMSUNG_UFS_
> +
> +#define PHY_COMN_BLK	1
> +#define PHY_TRSV_BLK	2
> +#define END_UFS_PHY_CFG { 0 }
> +#define PHY_TRSV_CH_OFFSET	0x30
> +#define PHY_APB_ADDR(off)	((off) << 2)
> +
> +#define PHY_COMN_REG_CFG(o, v, d) {	\
> +	.off_0 = PHY_APB_ADDR((o)),	\
> +	.off_1 = 0,		\
> +	.val = (v),		\
> +	.desc = (d),		\
> +	.id = PHY_COMN_BLK,	\
> +}
> +
> +#define PHY_TRSV_REG_CFG(o, v, d) {	\
> +	.off_0 = PHY_APB_ADDR((o)),	\
> +	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
> +	.val = (v),		\
> +	.desc = (d),		\
> +	.id = PHY_TRSV_BLK,	\
> +}
> +
> +/* UFS PHY registers */
> +#define PHY_PLL_LOCK_STATUS	0x1e
> +#define PHY_CDR_LOCK_STATUS	0x5e
> +
> +#define PHY_PLL_LOCK_BIT	BIT(5)
> +#define PHY_CDR_LOCK_BIT	BIT(4)
> +
> +/* PHY calibration point/state */
> +enum {
> +	CFG_PRE_INIT,
> +	CFG_POST_INIT,
> +	CFG_PRE_PWR_HS,
> +	CFG_POST_PWR_HS,
> +	CFG_TAG_MAX,
> +};
> +
> +struct samsung_ufs_phy_cfg {
> +	u32 off_0;
> +	u32 off_1;
> +	u32 val;
> +	u8 desc;
> +	u8 id;
> +};
> +
> +struct samsung_ufs_phy_drvdata {
> +	const struct samsung_ufs_phy_cfg **cfg;
> +	struct pmu_isol {
> +		u32 offset;
> +		u32 mask;
> +		u32 en;
> +	} isol;
> +};
> +
> +struct samsung_ufs_phy {
> +	struct device *dev;
> +	void __iomem *reg_pma;
> +	struct regmap *reg_pmu;
> +	struct clk *ref_clk;
> +	struct clk *ref_clk_parent;
> +	const struct samsung_ufs_phy_drvdata *drvdata;
> +	struct samsung_ufs_phy_cfg **cfg;
> +	const struct pmu_isol *isol;
> +	u8 lane_cnt;
> +	int ufs_phy_state;
> +	enum phy_mode mode;
> +	bool is_pre_init;
> +	bool is_post_init;
> +	bool is_pre_pmc;
> +	bool is_post_pmc;
> +};
> +
> +static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy *phy)
> +{
> +	return (struct samsung_ufs_phy *)phy_get_drvdata(phy);
> +}
> +
> +static inline void samsung_ufs_phy_ctrl_isol(
> +		struct samsung_ufs_phy *phy, u32 isol)
> +{
> +	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
> +			phy->isol->mask, isol ? 0 : phy->isol->en);
> +}
> +
> +#include "phy-exynos7-ufs.h"
> +
> +#endif /* _PHY_SAMSUNG_UFS_ */
> diff --git a/include/linux/phy/phy-samsung-ufs.h b/include/linux/phy/phy-samsung-ufs.h
> new file mode 100644
> index 000000000000..1def56207f5d
> --- /dev/null
> +++ b/include/linux/phy/phy-samsung-ufs.h
> @@ -0,0 +1,70 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +
> +#ifndef _PHY_EXYNOS_UFS_H_
> +#define _PHY_EXYNOS_UFS_H_
> +
> +#include "phy.h"
> +
> +/* description for PHY calibration */
> +enum {
> +	/* applicable to any */
> +	PWR_DESC_ANY	= 0,
> +	/* mode */
> +	PWR_DESC_PWM	= 1,
> +	PWR_DESC_HS	= 2,
> +	/* series */
> +	PWR_DESC_SER_A	= 1,
> +	PWR_DESC_SER_B	= 2,
> +	/* gear */
> +	PWR_DESC_G1	= 1,
> +	PWR_DESC_G2	= 2,
> +	PWR_DESC_G3	= 3,
> +	PWR_DESC_G4	= 4,
> +	PWR_DESC_G5	= 5,
> +	PWR_DESC_G6	= 6,
> +	PWR_DESC_G7	= 7,
> +	/* field mask */
> +	MD_MASK		= 0x3,
> +	SR_MASK		= 0x3,
> +	GR_MASK		= 0x7,
> +};
> +
> +#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
> +				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
> +#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
> +				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
> +#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_ANY		PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_HS)
> +#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_PWM)
> +#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_ANY)
> +#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
> +#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) == PWR_DESC_PWM)
> +#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
> +#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
> +#define COMP_PWR_MODE(a, b)		((a) == (b))
> +#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
> +					 (((b) >> 4) & GR_MASK))
> +#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK) == \
> +					 (((b) >> 2) & SR_MASK))
> +#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) == ((b) & MD_MASK))
> +
> +#endif /* _PHY_EXYNOS_UFS_H_ */
> 

Re: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Kishon Vijay Abraham I]

Hi Alim,

On 3/19/2020 8:30 PM, Alim Akhtar wrote:
> This patch introduces Samsung UFS PHY driver. This driver
> supports to deal with phy calibration and power control
> according to UFS host driver's behavior.
> 
> Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
> Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> ---
>  drivers/phy/samsung/Kconfig           |   9 +
>  drivers/phy/samsung/Makefile          |   1 +
>  drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
>  drivers/phy/samsung/phy-samsung-ufs.c | 311 ++++++++++++++++++++++++++
>  drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
>  include/linux/phy/phy-samsung-ufs.h   |  70 ++++++

Why is this added in include directory? will it be used by controller driver?

Thanks
Kishon
>  6 files changed, 576 insertions(+)
>  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
>  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
>  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> 
> diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
> index 9e483d1fdaf2..fc1e3c17f842 100644
> --- a/drivers/phy/samsung/Kconfig
> +++ b/drivers/phy/samsung/Kconfig
> @@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
>  	  Enable PCIe PHY support for Exynos SoC series.
>  	  This driver provides PHY interface for Exynos PCIe controller.
>  
> +config PHY_SAMSUNG_UFS
> +	tristate "SAMSUNG SoC series UFS PHY driver"
> +	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
> +	select GENERIC_PHY
> +	help
> +	  Enable this to support the Samsung UFS PHY driver for
> +	  Samsung SoCs. This driver provides the interface for UFS
> +	  host controller to do PHY related programming.
> +
>  config PHY_SAMSUNG_USB2
>  	tristate "Samsung USB 2.0 PHY driver"
>  	depends on HAS_IOMEM
> diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
> index db9b1aa0de6e..3959100fe8a2 100644
> --- a/drivers/phy/samsung/Makefile
> +++ b/drivers/phy/samsung/Makefile
> @@ -2,6 +2,7 @@
>  obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
>  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
>  obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
> +obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
>  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
>  phy-exynos-usb2-y			+= phy-samsung-usb2.o
>  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
> diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h b/drivers/phy/samsung/phy-exynos7-ufs.h
> new file mode 100644
> index 000000000000..da981c1ac040
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-exynos7-ufs.h
> @@ -0,0 +1,85 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * UFS PHY driver data for Samsung EXYNOS7 SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + */
> +#ifndef _PHY_EXYNOS7_UFS_H_
> +#define _PHY_EXYNOS7_UFS_H_
> +
> +#include "phy-samsung-ufs.h"
> +
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
> +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
> +
> +/* Calibration for phy initialization */
> +static const struct samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
> +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
> +	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
> +	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
> +	END_UFS_PHY_CFG
> +};
> +
> +static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
> +	END_UFS_PHY_CFG
> +};
> +
> +/* Calibration for HS mode series A/B */
> +static const struct samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
> +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
> +	/* Setting order: 1st(0x16, 2nd(0x15) */
> +	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
> +	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
> +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
> +	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
> +	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
> +	END_UFS_PHY_CFG
> +};
> +
> +/* Calibration for HS mode series A/B atfer PMC */
> +static const struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
> +	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
> +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
> +	END_UFS_PHY_CFG
> +};
> +
> +static const struct samsung_ufs_phy_cfg *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
> +	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
> +	[CFG_POST_INIT]		= exynos7_post_init_cfg,
> +	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
> +	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
> +};
> +
> +static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
> +	.cfg = exynos7_ufs_phy_cfgs,
> +	.isol = {
> +		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
> +		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
> +		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
> +	},
> +};
> +
> +#endif /* _PHY_EXYNOS7_UFS_H_ */
> diff --git a/drivers/phy/samsung/phy-samsung-ufs.c b/drivers/phy/samsung/phy-samsung-ufs.c
> new file mode 100644
> index 000000000000..2d5db24de49b
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-samsung-ufs.c
> @@ -0,0 +1,311 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * UFS PHY driver for Samsung SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/phy/phy.h>
> +#include <linux/phy/phy-samsung-ufs.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include "phy-samsung-ufs.h"
> +
> +#define for_each_phy_lane(phy, i) \
> +	for (i = 0; i < (phy)->lane_cnt; i++)
> +#define for_each_phy_cfg(cfg) \
> +	for (; (cfg)->id; (cfg)++)
> +
> +#define PHY_DEF_LANE_CNT	1
> +
> +static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
> +			const struct samsung_ufs_phy_cfg *cfg, u8 lane)
> +{
> +	enum {LANE_0, LANE_1}; /* lane index */
> +
> +	switch (lane) {
> +	case LANE_0:
> +		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
> +		break;
> +	case LANE_1:
> +		if (cfg->id == PHY_TRSV_BLK)
> +			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
> +		break;
> +	}
> +}
> +
> +int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> +	const unsigned int timeout_us = 100000;
> +	const unsigned int sleep_us = 10;
> +	u32 val;
> +	int err;
> +
> +	err = readl_poll_timeout(
> +			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
> +			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
> +	if (err) {
> +		dev_err(ufs_phy->dev,
> +			"failed to get phy pll lock acquisition %d\n", err);
> +		goto out;
> +	}
> +
> +	err = readl_poll_timeout(
> +			ufs_phy->reg_pma + PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
> +			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
> +	if (err) {
> +		dev_err(ufs_phy->dev,
> +			"failed to get phy cdr lock acquisition %d\n", err);
> +		goto out;
> +	}
> +
> +out:
> +	return err;
> +}
> +
> +int samsung_ufs_phy_calibrate(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> +	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
> +	const struct samsung_ufs_phy_cfg *cfg;
> +	int i;
> +	int err = 0;
> +
> +	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
> +		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
> +		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
> +							ufs_phy->ufs_phy_state);
> +		return -EINVAL;
> +	}
> +
> +	if (ufs_phy->is_pre_init)
> +		ufs_phy->is_pre_init = false;
> +	if (ufs_phy->is_post_init) {
> +		ufs_phy->is_post_init = false;
> +		ufs_phy->ufs_phy_state = CFG_POST_INIT;
> +	}
> +	if (ufs_phy->is_pre_pmc) {
> +		ufs_phy->is_pre_pmc = false;
> +		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
> +	}
> +	if (ufs_phy->is_post_pmc) {
> +		ufs_phy->is_post_pmc = false;
> +		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
> +	}
> +
> +	switch (ufs_phy->ufs_phy_state) {
> +	case CFG_PRE_INIT:
> +		ufs_phy->is_post_init = true;
> +		break;
> +	case CFG_POST_INIT:
> +		ufs_phy->is_pre_pmc = true;
> +		break;
> +	case CFG_PRE_PWR_HS:
> +		ufs_phy->is_post_pmc = true;
> +		break;
> +	case CFG_POST_PWR_HS:
> +		break;
> +	default:
> +		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
> +	}
> +
> +	cfg = cfgs[ufs_phy->ufs_phy_state];
> +	if (!cfg)
> +		goto out;
> +
> +	for_each_phy_cfg(cfg) {
> +		for_each_phy_lane(ufs_phy, i) {
> +			samsung_ufs_phy_config(ufs_phy, cfg, i);
> +		}
> +	}
> +
> +	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
> +		err = samsung_ufs_phy_wait_for_lock_acq(phy);
> +out:
> +	return err;
> +}
> +
> +static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy)
> +{
> +	struct clk *child, *parent;
> +
> +	child = devm_clk_get(phy->dev, "ref_clk");
> +	if (IS_ERR(child))
> +		dev_err(phy->dev, "failed to get ref_clk clock\n");
> +	else
> +		phy->ref_clk = child;
> +
> +	parent = devm_clk_get(phy->dev, "ref_clk_parent");
> +	if (IS_ERR(parent))
> +		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
> +	else
> +		phy->ref_clk_parent = parent;
> +
> +	return clk_set_parent(child, parent);
> +}
> +
> +static int samsung_ufs_phy_init(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +
> +	_phy->lane_cnt = phy->attrs.bus_width;
> +	_phy->ufs_phy_state = CFG_PRE_INIT;
> +
> +	_phy->is_pre_init = true;
> +	_phy->is_post_init = false;
> +	_phy->is_pre_pmc = false;
> +	_phy->is_post_pmc = false;
> +
> +	samsung_ufs_phy_clks_init(_phy);
> +
> +	samsung_ufs_phy_calibrate(phy);
> +
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_power_on(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +	int ret;
> +
> +	ret = clk_prepare_enable(_phy->ref_clk);
> +	if (ret) {
> +		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
> +				__func__, ret);
> +		return ret;
> +	}
> +
> +	samsung_ufs_phy_ctrl_isol(_phy, false);
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_power_off(struct phy *phy)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> +
> +	samsung_ufs_phy_ctrl_isol(_phy, true);
> +	clk_disable_unprepare(_phy->ref_clk);
> +	return 0;
> +}
> +
> +static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
> +					enum phy_mode mode, int submode)
> +{
> +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
> +
> +	_phy->mode = PHY_MODE_INVALID;
> +
> +	if (mode > 0)
> +		_phy->mode = mode;
> +
> +	return 0;
> +}
> +
> +static struct phy_ops samsung_ufs_phy_ops = {
> +	.init		= samsung_ufs_phy_init,
> +	.power_on	= samsung_ufs_phy_power_on,
> +	.power_off	= samsung_ufs_phy_power_off,
> +	.calibrate	= samsung_ufs_phy_calibrate,
> +	.set_mode	= samsung_ufs_phy_set_mode,
> +}
> +;
> +static const struct of_device_id samsung_ufs_phy_match[];
> +
> +static int samsung_ufs_phy_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	const struct of_device_id *match;
> +	struct samsung_ufs_phy *phy;
> +	struct phy *gen_phy;
> +	struct phy_provider *phy_provider;
> +	const struct samsung_ufs_phy_drvdata *drvdata;
> +	int err = 0;
> +
> +	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
> +	if (!match) {
> +		err = -EINVAL;
> +		dev_err(dev, "failed to get match_node\n");
> +		goto out;
> +	}
> +
> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy) {
> +		err = -ENOMEM;
> +		goto out;
> +	}
> +
> +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-pma");
> +	phy->reg_pma = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(phy->reg_pma)) {
> +		err = PTR_ERR(phy->reg_pma);
> +		goto out;
> +	}
> +
> +	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
> +				dev->of_node, "samsung,pmu-syscon");
> +	if (IS_ERR(phy->reg_pmu)) {
> +		err = PTR_ERR(phy->reg_pmu);
> +		dev_err(dev, "failed syscon remap for pmu\n");
> +		goto out;
> +	}
> +
> +	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
> +	if (IS_ERR(gen_phy)) {
> +		err = PTR_ERR(gen_phy);
> +		dev_err(dev, "failed to create PHY for ufs-phy\n");
> +		goto out;
> +	}
> +
> +	drvdata = match->data;
> +	phy->dev = dev;
> +	phy->drvdata = drvdata;
> +	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
> +	phy->isol = &drvdata->isol;
> +	phy->lane_cnt = PHY_DEF_LANE_CNT;
> +
> +	phy_set_drvdata(gen_phy, phy);
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider)) {
> +		err = PTR_ERR(phy_provider);
> +		dev_err(dev, "failed to register phy-provider\n");
> +		goto out;
> +	}
> +out:
> +	return err;
> +}
> +
> +static const struct of_device_id samsung_ufs_phy_match[] = {
> +	{
> +		.compatible = "samsung,exynos7-ufs-phy",
> +		.data = &exynos7_ufs_phy,
> +	},
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
> +
> +static struct platform_driver samsung_ufs_phy_driver = {
> +	.probe  = samsung_ufs_phy_probe,
> +	.driver = {
> +		.name = "samsung-ufs-phy",
> +		.of_match_table = samsung_ufs_phy_match,
> +	},
> +};
> +module_platform_driver(samsung_ufs_phy_driver);
> +MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
> +MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
> +MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
> +MODULE_LICENSE("GPL v2");
> diff --git a/drivers/phy/samsung/phy-samsung-ufs.h b/drivers/phy/samsung/phy-samsung-ufs.h
> new file mode 100644
> index 000000000000..d0ae2b416b2b
> --- /dev/null
> +++ b/drivers/phy/samsung/phy-samsung-ufs.h
> @@ -0,0 +1,100 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * UFS PHY driver for Samsung EXYNOS SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +#ifndef _PHY_SAMSUNG_UFS_
> +#define _PHY_SAMSUNG_UFS_
> +
> +#define PHY_COMN_BLK	1
> +#define PHY_TRSV_BLK	2
> +#define END_UFS_PHY_CFG { 0 }
> +#define PHY_TRSV_CH_OFFSET	0x30
> +#define PHY_APB_ADDR(off)	((off) << 2)
> +
> +#define PHY_COMN_REG_CFG(o, v, d) {	\
> +	.off_0 = PHY_APB_ADDR((o)),	\
> +	.off_1 = 0,		\
> +	.val = (v),		\
> +	.desc = (d),		\
> +	.id = PHY_COMN_BLK,	\
> +}
> +
> +#define PHY_TRSV_REG_CFG(o, v, d) {	\
> +	.off_0 = PHY_APB_ADDR((o)),	\
> +	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
> +	.val = (v),		\
> +	.desc = (d),		\
> +	.id = PHY_TRSV_BLK,	\
> +}
> +
> +/* UFS PHY registers */
> +#define PHY_PLL_LOCK_STATUS	0x1e
> +#define PHY_CDR_LOCK_STATUS	0x5e
> +
> +#define PHY_PLL_LOCK_BIT	BIT(5)
> +#define PHY_CDR_LOCK_BIT	BIT(4)
> +
> +/* PHY calibration point/state */
> +enum {
> +	CFG_PRE_INIT,
> +	CFG_POST_INIT,
> +	CFG_PRE_PWR_HS,
> +	CFG_POST_PWR_HS,
> +	CFG_TAG_MAX,
> +};
> +
> +struct samsung_ufs_phy_cfg {
> +	u32 off_0;
> +	u32 off_1;
> +	u32 val;
> +	u8 desc;
> +	u8 id;
> +};
> +
> +struct samsung_ufs_phy_drvdata {
> +	const struct samsung_ufs_phy_cfg **cfg;
> +	struct pmu_isol {
> +		u32 offset;
> +		u32 mask;
> +		u32 en;
> +	} isol;
> +};
> +
> +struct samsung_ufs_phy {
> +	struct device *dev;
> +	void __iomem *reg_pma;
> +	struct regmap *reg_pmu;
> +	struct clk *ref_clk;
> +	struct clk *ref_clk_parent;
> +	const struct samsung_ufs_phy_drvdata *drvdata;
> +	struct samsung_ufs_phy_cfg **cfg;
> +	const struct pmu_isol *isol;
> +	u8 lane_cnt;
> +	int ufs_phy_state;
> +	enum phy_mode mode;
> +	bool is_pre_init;
> +	bool is_post_init;
> +	bool is_pre_pmc;
> +	bool is_post_pmc;
> +};
> +
> +static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy *phy)
> +{
> +	return (struct samsung_ufs_phy *)phy_get_drvdata(phy);
> +}
> +
> +static inline void samsung_ufs_phy_ctrl_isol(
> +		struct samsung_ufs_phy *phy, u32 isol)
> +{
> +	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
> +			phy->isol->mask, isol ? 0 : phy->isol->en);
> +}
> +
> +#include "phy-exynos7-ufs.h"
> +
> +#endif /* _PHY_SAMSUNG_UFS_ */
> diff --git a/include/linux/phy/phy-samsung-ufs.h b/include/linux/phy/phy-samsung-ufs.h
> new file mode 100644
> index 000000000000..1def56207f5d
> --- /dev/null
> +++ b/include/linux/phy/phy-samsung-ufs.h
> @@ -0,0 +1,70 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
> + *
> + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> + * Author: Seungwon Jeon <essuuj@gmail.com>
> + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> + *
> + */
> +
> +#ifndef _PHY_EXYNOS_UFS_H_
> +#define _PHY_EXYNOS_UFS_H_
> +
> +#include "phy.h"
> +
> +/* description for PHY calibration */
> +enum {
> +	/* applicable to any */
> +	PWR_DESC_ANY	= 0,
> +	/* mode */
> +	PWR_DESC_PWM	= 1,
> +	PWR_DESC_HS	= 2,
> +	/* series */
> +	PWR_DESC_SER_A	= 1,
> +	PWR_DESC_SER_B	= 2,
> +	/* gear */
> +	PWR_DESC_G1	= 1,
> +	PWR_DESC_G2	= 2,
> +	PWR_DESC_G3	= 3,
> +	PWR_DESC_G4	= 4,
> +	PWR_DESC_G5	= 5,
> +	PWR_DESC_G6	= 6,
> +	PWR_DESC_G7	= 7,
> +	/* field mask */
> +	MD_MASK		= 0x3,
> +	SR_MASK		= 0x3,
> +	GR_MASK		= 0x7,
> +};
> +
> +#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
> +				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
> +#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
> +				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
> +#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_ANY)
> +#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_A)
> +#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3, PWR_DESC_SER_B)
> +#define PWR_MODE_HS_ANY		PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_HS)
> +#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_PWM)
> +#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
> +					 PWR_DESC_ANY, PWR_DESC_ANY)
> +#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
> +#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) == PWR_DESC_PWM)
> +#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
> +#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
> +#define COMP_PWR_MODE(a, b)		((a) == (b))
> +#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
> +					 (((b) >> 4) & GR_MASK))
> +#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK) == \
> +					 (((b) >> 2) & SR_MASK))
> +#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) == ((b) & MD_MASK))
> +
> +#endif /* _PHY_EXYNOS_UFS_H_ */
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Alim Akhtar]

Hi Kishon

> -----Original Message-----
> From: Kishon Vijay Abraham I <kishon@ti.com>
> Sent: 20 March 2020 11:10
> To: Alim Akhtar <alim.akhtar@samsung.com>; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Cc: krzk@kernel.org; avri.altman@wdc.com; martin.petersen@oracle.com;
> kwmad.kim@samsung.com; stanley.chu@mediatek.com;
> cang@codeaurora.org; linux-samsung-soc@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org
> Subject: Re: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung
> SoC
> 
> Hi Alim,
> 
> On 3/19/2020 8:30 PM, Alim Akhtar wrote:
> > This patch introduces Samsung UFS PHY driver. This driver supports to
> > deal with phy calibration and power control according to UFS host
> > driver's behavior.
> >
> > Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
> > Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> > Cc: Kishon Vijay Abraham I <kishon@ti.com>
> > ---
> >  drivers/phy/samsung/Kconfig           |   9 +
> >  drivers/phy/samsung/Makefile          |   1 +
> >  drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
> > drivers/phy/samsung/phy-samsung-ufs.c | 311
> ++++++++++++++++++++++++++
> > drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
> >  include/linux/phy/phy-samsung-ufs.h   |  70 ++++++
> 
> Why is this added in include directory? will it be used by controller driver?
> 
Thanks for point this out, as of today it is not used in ufs controller driver. Will move this to driver directory.

> Thanks
> Kishon
> >  6 files changed, 576 insertions(+)
> >  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
> >  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> >
> > diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
> > index 9e483d1fdaf2..fc1e3c17f842 100644
> > --- a/drivers/phy/samsung/Kconfig
> > +++ b/drivers/phy/samsung/Kconfig
> > @@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
> >  	  Enable PCIe PHY support for Exynos SoC series.
> >  	  This driver provides PHY interface for Exynos PCIe controller.
> >
> > +config PHY_SAMSUNG_UFS
> > +	tristate "SAMSUNG SoC series UFS PHY driver"
> > +	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
> > +	select GENERIC_PHY
> > +	help
> > +	  Enable this to support the Samsung UFS PHY driver for
> > +	  Samsung SoCs. This driver provides the interface for UFS
> > +	  host controller to do PHY related programming.
> > +
> >  config PHY_SAMSUNG_USB2
> >  	tristate "Samsung USB 2.0 PHY driver"
> >  	depends on HAS_IOMEM
> > diff --git a/drivers/phy/samsung/Makefile
> > b/drivers/phy/samsung/Makefile index db9b1aa0de6e..3959100fe8a2 100644
> > --- a/drivers/phy/samsung/Makefile
> > +++ b/drivers/phy/samsung/Makefile
> > @@ -2,6 +2,7 @@
> >  obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
> >  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
> >  obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
> > +obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> >  phy-exynos-usb2-y			+= phy-samsung-usb2.o
> >  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-
> usb2.o
> > diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h
> > b/drivers/phy/samsung/phy-exynos7-ufs.h
> > new file mode 100644
> > index 000000000000..da981c1ac040
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-exynos7-ufs.h
> > @@ -0,0 +1,85 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * UFS PHY driver data for Samsung EXYNOS7 SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + */
> > +#ifndef _PHY_EXYNOS7_UFS_H_
> > +#define _PHY_EXYNOS7_UFS_H_
> > +
> > +#include "phy-samsung-ufs.h"
> > +
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
> > +
> > +/* Calibration for phy initialization */ static const struct
> > +samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +/* Calibration for HS mode series A/B */ static const struct
> > +samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
> > +	/* Setting order: 1st(0x16, 2nd(0x15) */
> > +	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
> > +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
> > +	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +/* Calibration for HS mode series A/B atfer PMC */ static const
> > +struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +static const struct samsung_ufs_phy_cfg
> *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
> > +	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
> > +	[CFG_POST_INIT]		= exynos7_post_init_cfg,
> > +	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
> > +	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
> > +};
> > +
> > +static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
> > +	.cfg = exynos7_ufs_phy_cfgs,
> > +	.isol = {
> > +		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
> > +		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
> > +		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
> > +	},
> > +};
> > +
> > +#endif /* _PHY_EXYNOS7_UFS_H_ */
> > diff --git a/drivers/phy/samsung/phy-samsung-ufs.c
> > b/drivers/phy/samsung/phy-samsung-ufs.c
> > new file mode 100644
> > index 000000000000..2d5db24de49b
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-samsung-ufs.c
> > @@ -0,0 +1,311 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * UFS PHY driver for Samsung SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include <linux/of.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/phy/phy-samsung-ufs.h> #include
> > +<linux/platform_device.h> #include <linux/regmap.h>
> > +
> > +#include "phy-samsung-ufs.h"
> > +
> > +#define for_each_phy_lane(phy, i) \
> > +	for (i = 0; i < (phy)->lane_cnt; i++) #define for_each_phy_cfg(cfg)
> > +\
> > +	for (; (cfg)->id; (cfg)++)
> > +
> > +#define PHY_DEF_LANE_CNT	1
> > +
> > +static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
> > +			const struct samsung_ufs_phy_cfg *cfg, u8 lane) {
> > +	enum {LANE_0, LANE_1}; /* lane index */
> > +
> > +	switch (lane) {
> > +	case LANE_0:
> > +		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
> > +		break;
> > +	case LANE_1:
> > +		if (cfg->id == PHY_TRSV_BLK)
> > +			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
> > +		break;
> > +	}
> > +}
> > +
> > +int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy) {
> > +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> > +	const unsigned int timeout_us = 100000;
> > +	const unsigned int sleep_us = 10;
> > +	u32 val;
> > +	int err;
> > +
> > +	err = readl_poll_timeout(
> > +			ufs_phy->reg_pma +
> PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
> > +			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
> > +	if (err) {
> > +		dev_err(ufs_phy->dev,
> > +			"failed to get phy pll lock acquisition %d\n", err);
> > +		goto out;
> > +	}
> > +
> > +	err = readl_poll_timeout(
> > +			ufs_phy->reg_pma +
> PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
> > +			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
> > +	if (err) {
> > +		dev_err(ufs_phy->dev,
> > +			"failed to get phy cdr lock acquisition %d\n", err);
> > +		goto out;
> > +	}
> > +
> > +out:
> > +	return err;
> > +}
> > +
> > +int samsung_ufs_phy_calibrate(struct phy *phy) {
> > +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> > +	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
> > +	const struct samsung_ufs_phy_cfg *cfg;
> > +	int i;
> > +	int err = 0;
> > +
> > +	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
> > +		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
> > +		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
> > +							ufs_phy-
> >ufs_phy_state);
> > +		return -EINVAL;
> > +	}
> > +
> > +	if (ufs_phy->is_pre_init)
> > +		ufs_phy->is_pre_init = false;
> > +	if (ufs_phy->is_post_init) {
> > +		ufs_phy->is_post_init = false;
> > +		ufs_phy->ufs_phy_state = CFG_POST_INIT;
> > +	}
> > +	if (ufs_phy->is_pre_pmc) {
> > +		ufs_phy->is_pre_pmc = false;
> > +		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
> > +	}
> > +	if (ufs_phy->is_post_pmc) {
> > +		ufs_phy->is_post_pmc = false;
> > +		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
> > +	}
> > +
> > +	switch (ufs_phy->ufs_phy_state) {
> > +	case CFG_PRE_INIT:
> > +		ufs_phy->is_post_init = true;
> > +		break;
> > +	case CFG_POST_INIT:
> > +		ufs_phy->is_pre_pmc = true;
> > +		break;
> > +	case CFG_PRE_PWR_HS:
> > +		ufs_phy->is_post_pmc = true;
> > +		break;
> > +	case CFG_POST_PWR_HS:
> > +		break;
> > +	default:
> > +		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
> > +	}
> > +
> > +	cfg = cfgs[ufs_phy->ufs_phy_state];
> > +	if (!cfg)
> > +		goto out;
> > +
> > +	for_each_phy_cfg(cfg) {
> > +		for_each_phy_lane(ufs_phy, i) {
> > +			samsung_ufs_phy_config(ufs_phy, cfg, i);
> > +		}
> > +	}
> > +
> > +	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
> > +		err = samsung_ufs_phy_wait_for_lock_acq(phy);
> > +out:
> > +	return err;
> > +}
> > +
> > +static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy) {
> > +	struct clk *child, *parent;
> > +
> > +	child = devm_clk_get(phy->dev, "ref_clk");
> > +	if (IS_ERR(child))
> > +		dev_err(phy->dev, "failed to get ref_clk clock\n");
> > +	else
> > +		phy->ref_clk = child;
> > +
> > +	parent = devm_clk_get(phy->dev, "ref_clk_parent");
> > +	if (IS_ERR(parent))
> > +		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
> > +	else
> > +		phy->ref_clk_parent = parent;
> > +
> > +	return clk_set_parent(child, parent); }
> > +
> > +static int samsung_ufs_phy_init(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +
> > +	_phy->lane_cnt = phy->attrs.bus_width;
> > +	_phy->ufs_phy_state = CFG_PRE_INIT;
> > +
> > +	_phy->is_pre_init = true;
> > +	_phy->is_post_init = false;
> > +	_phy->is_pre_pmc = false;
> > +	_phy->is_post_pmc = false;
> > +
> > +	samsung_ufs_phy_clks_init(_phy);
> > +
> > +	samsung_ufs_phy_calibrate(phy);
> > +
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_power_on(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +	int ret;
> > +
> > +	ret = clk_prepare_enable(_phy->ref_clk);
> > +	if (ret) {
> > +		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
> > +				__func__, ret);
> > +		return ret;
> > +	}
> > +
> > +	samsung_ufs_phy_ctrl_isol(_phy, false);
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_power_off(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +
> > +	samsung_ufs_phy_ctrl_isol(_phy, true);
> > +	clk_disable_unprepare(_phy->ref_clk);
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
> > +					enum phy_mode mode, int submode) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
> > +
> > +	_phy->mode = PHY_MODE_INVALID;
> > +
> > +	if (mode > 0)
> > +		_phy->mode = mode;
> > +
> > +	return 0;
> > +}
> > +
> > +static struct phy_ops samsung_ufs_phy_ops = {
> > +	.init		= samsung_ufs_phy_init,
> > +	.power_on	= samsung_ufs_phy_power_on,
> > +	.power_off	= samsung_ufs_phy_power_off,
> > +	.calibrate	= samsung_ufs_phy_calibrate,
> > +	.set_mode	= samsung_ufs_phy_set_mode,
> > +}
> > +;
> > +static const struct of_device_id samsung_ufs_phy_match[];
> > +
> > +static int samsung_ufs_phy_probe(struct platform_device *pdev) {
> > +	struct device *dev = &pdev->dev;
> > +	struct resource *res;
> > +	const struct of_device_id *match;
> > +	struct samsung_ufs_phy *phy;
> > +	struct phy *gen_phy;
> > +	struct phy_provider *phy_provider;
> > +	const struct samsung_ufs_phy_drvdata *drvdata;
> > +	int err = 0;
> > +
> > +	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
> > +	if (!match) {
> > +		err = -EINVAL;
> > +		dev_err(dev, "failed to get match_node\n");
> > +		goto out;
> > +	}
> > +
> > +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> > +	if (!phy) {
> > +		err = -ENOMEM;
> > +		goto out;
> > +	}
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-
> pma");
> > +	phy->reg_pma = devm_ioremap_resource(dev, res);
> > +	if (IS_ERR(phy->reg_pma)) {
> > +		err = PTR_ERR(phy->reg_pma);
> > +		goto out;
> > +	}
> > +
> > +	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
> > +				dev->of_node, "samsung,pmu-syscon");
> > +	if (IS_ERR(phy->reg_pmu)) {
> > +		err = PTR_ERR(phy->reg_pmu);
> > +		dev_err(dev, "failed syscon remap for pmu\n");
> > +		goto out;
> > +	}
> > +
> > +	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
> > +	if (IS_ERR(gen_phy)) {
> > +		err = PTR_ERR(gen_phy);
> > +		dev_err(dev, "failed to create PHY for ufs-phy\n");
> > +		goto out;
> > +	}
> > +
> > +	drvdata = match->data;
> > +	phy->dev = dev;
> > +	phy->drvdata = drvdata;
> > +	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
> > +	phy->isol = &drvdata->isol;
> > +	phy->lane_cnt = PHY_DEF_LANE_CNT;
> > +
> > +	phy_set_drvdata(gen_phy, phy);
> > +
> > +	phy_provider = devm_of_phy_provider_register(dev,
> of_phy_simple_xlate);
> > +	if (IS_ERR(phy_provider)) {
> > +		err = PTR_ERR(phy_provider);
> > +		dev_err(dev, "failed to register phy-provider\n");
> > +		goto out;
> > +	}
> > +out:
> > +	return err;
> > +}
> > +
> > +static const struct of_device_id samsung_ufs_phy_match[] = {
> > +	{
> > +		.compatible = "samsung,exynos7-ufs-phy",
> > +		.data = &exynos7_ufs_phy,
> > +	},
> > +	{},
> > +};
> > +MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
> > +
> > +static struct platform_driver samsung_ufs_phy_driver = {
> > +	.probe  = samsung_ufs_phy_probe,
> > +	.driver = {
> > +		.name = "samsung-ufs-phy",
> > +		.of_match_table = samsung_ufs_phy_match,
> > +	},
> > +};
> > +module_platform_driver(samsung_ufs_phy_driver);
> > +MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
> > +MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
> > +MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/phy/samsung/phy-samsung-ufs.h
> > b/drivers/phy/samsung/phy-samsung-ufs.h
> > new file mode 100644
> > index 000000000000..d0ae2b416b2b
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-samsung-ufs.h
> > @@ -0,0 +1,100 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * UFS PHY driver for Samsung EXYNOS SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +#ifndef _PHY_SAMSUNG_UFS_
> > +#define _PHY_SAMSUNG_UFS_
> > +
> > +#define PHY_COMN_BLK	1
> > +#define PHY_TRSV_BLK	2
> > +#define END_UFS_PHY_CFG { 0 }
> > +#define PHY_TRSV_CH_OFFSET	0x30
> > +#define PHY_APB_ADDR(off)	((off) << 2)
> > +
> > +#define PHY_COMN_REG_CFG(o, v, d) {	\
> > +	.off_0 = PHY_APB_ADDR((o)),	\
> > +	.off_1 = 0,		\
> > +	.val = (v),		\
> > +	.desc = (d),		\
> > +	.id = PHY_COMN_BLK,	\
> > +}
> > +
> > +#define PHY_TRSV_REG_CFG(o, v, d) {	\
> > +	.off_0 = PHY_APB_ADDR((o)),	\
> > +	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
> > +	.val = (v),		\
> > +	.desc = (d),		\
> > +	.id = PHY_TRSV_BLK,	\
> > +}
> > +
> > +/* UFS PHY registers */
> > +#define PHY_PLL_LOCK_STATUS	0x1e
> > +#define PHY_CDR_LOCK_STATUS	0x5e
> > +
> > +#define PHY_PLL_LOCK_BIT	BIT(5)
> > +#define PHY_CDR_LOCK_BIT	BIT(4)
> > +
> > +/* PHY calibration point/state */
> > +enum {
> > +	CFG_PRE_INIT,
> > +	CFG_POST_INIT,
> > +	CFG_PRE_PWR_HS,
> > +	CFG_POST_PWR_HS,
> > +	CFG_TAG_MAX,
> > +};
> > +
> > +struct samsung_ufs_phy_cfg {
> > +	u32 off_0;
> > +	u32 off_1;
> > +	u32 val;
> > +	u8 desc;
> > +	u8 id;
> > +};
> > +
> > +struct samsung_ufs_phy_drvdata {
> > +	const struct samsung_ufs_phy_cfg **cfg;
> > +	struct pmu_isol {
> > +		u32 offset;
> > +		u32 mask;
> > +		u32 en;
> > +	} isol;
> > +};
> > +
> > +struct samsung_ufs_phy {
> > +	struct device *dev;
> > +	void __iomem *reg_pma;
> > +	struct regmap *reg_pmu;
> > +	struct clk *ref_clk;
> > +	struct clk *ref_clk_parent;
> > +	const struct samsung_ufs_phy_drvdata *drvdata;
> > +	struct samsung_ufs_phy_cfg **cfg;
> > +	const struct pmu_isol *isol;
> > +	u8 lane_cnt;
> > +	int ufs_phy_state;
> > +	enum phy_mode mode;
> > +	bool is_pre_init;
> > +	bool is_post_init;
> > +	bool is_pre_pmc;
> > +	bool is_post_pmc;
> > +};
> > +
> > +static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy
> > +*phy) {
> > +	return (struct samsung_ufs_phy *)phy_get_drvdata(phy); }
> > +
> > +static inline void samsung_ufs_phy_ctrl_isol(
> > +		struct samsung_ufs_phy *phy, u32 isol) {
> > +	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
> > +			phy->isol->mask, isol ? 0 : phy->isol->en); }
> > +
> > +#include "phy-exynos7-ufs.h"
> > +
> > +#endif /* _PHY_SAMSUNG_UFS_ */
> > diff --git a/include/linux/phy/phy-samsung-ufs.h
> > b/include/linux/phy/phy-samsung-ufs.h
> > new file mode 100644
> > index 000000000000..1def56207f5d
> > --- /dev/null
> > +++ b/include/linux/phy/phy-samsung-ufs.h
> > @@ -0,0 +1,70 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +
> > +#ifndef _PHY_EXYNOS_UFS_H_
> > +#define _PHY_EXYNOS_UFS_H_
> > +
> > +#include "phy.h"
> > +
> > +/* description for PHY calibration */ enum {
> > +	/* applicable to any */
> > +	PWR_DESC_ANY	= 0,
> > +	/* mode */
> > +	PWR_DESC_PWM	= 1,
> > +	PWR_DESC_HS	= 2,
> > +	/* series */
> > +	PWR_DESC_SER_A	= 1,
> > +	PWR_DESC_SER_B	= 2,
> > +	/* gear */
> > +	PWR_DESC_G1	= 1,
> > +	PWR_DESC_G2	= 2,
> > +	PWR_DESC_G3	= 3,
> > +	PWR_DESC_G4	= 4,
> > +	PWR_DESC_G5	= 5,
> > +	PWR_DESC_G6	= 6,
> > +	PWR_DESC_G7	= 7,
> > +	/* field mask */
> > +	MD_MASK		= 0x3,
> > +	SR_MASK		= 0x3,
> > +	GR_MASK		= 0x7,
> > +};
> > +
> > +#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
> > +				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
> > +#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
> > +				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
> > +#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_ANY
> 	PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_HS)
> > +#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_PWM)
> > +#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_ANY)
> > +#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
> > +#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) ==
> PWR_DESC_PWM)
> > +#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
> > +#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
> > +#define COMP_PWR_MODE(a, b)		((a) == (b))
> > +#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
> > +					 (((b) >> 4) & GR_MASK))
> > +#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK)
> == \
> > +					 (((b) >> 2) & SR_MASK))
> > +#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) ==
> ((b) & MD_MASK))
> > +
> > +#endif /* _PHY_EXYNOS_UFS_H_ */
> >

RE: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung SoC

[Alim Akhtar]

Hi Kishon

> -----Original Message-----
> From: Kishon Vijay Abraham I <kishon@ti.com>
> Sent: 20 March 2020 11:10
> To: Alim Akhtar <alim.akhtar@samsung.com>; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Cc: krzk@kernel.org; avri.altman@wdc.com; martin.petersen@oracle.com;
> kwmad.kim@samsung.com; stanley.chu@mediatek.com;
> cang@codeaurora.org; linux-samsung-soc@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org
> Subject: Re: [PATCH v3 2/5] phy: samsung-ufs: add UFS PHY driver for samsung
> SoC
> 
> Hi Alim,
> 
> On 3/19/2020 8:30 PM, Alim Akhtar wrote:
> > This patch introduces Samsung UFS PHY driver. This driver supports to
> > deal with phy calibration and power control according to UFS host
> > driver's behavior.
> >
> > Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
> > Signed-off-by: Seungwon Jeon <essuuj@gmail.com>
> > Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
> > Cc: Kishon Vijay Abraham I <kishon@ti.com>
> > ---
> >  drivers/phy/samsung/Kconfig           |   9 +
> >  drivers/phy/samsung/Makefile          |   1 +
> >  drivers/phy/samsung/phy-exynos7-ufs.h |  85 +++++++
> > drivers/phy/samsung/phy-samsung-ufs.c | 311
> ++++++++++++++++++++++++++
> > drivers/phy/samsung/phy-samsung-ufs.h | 100 +++++++++
> >  include/linux/phy/phy-samsung-ufs.h   |  70 ++++++
> 
> Why is this added in include directory? will it be used by controller driver?
> 
Thanks for point this out, as of today it is not used in ufs controller driver. Will move this to driver directory.

> Thanks
> Kishon
> >  6 files changed, 576 insertions(+)
> >  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
> >  create mode 100644 include/linux/phy/phy-samsung-ufs.h
> >
> > diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
> > index 9e483d1fdaf2..fc1e3c17f842 100644
> > --- a/drivers/phy/samsung/Kconfig
> > +++ b/drivers/phy/samsung/Kconfig
> > @@ -29,6 +29,15 @@ config PHY_EXYNOS_PCIE
> >  	  Enable PCIe PHY support for Exynos SoC series.
> >  	  This driver provides PHY interface for Exynos PCIe controller.
> >
> > +config PHY_SAMSUNG_UFS
> > +	tristate "SAMSUNG SoC series UFS PHY driver"
> > +	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
> > +	select GENERIC_PHY
> > +	help
> > +	  Enable this to support the Samsung UFS PHY driver for
> > +	  Samsung SoCs. This driver provides the interface for UFS
> > +	  host controller to do PHY related programming.
> > +
> >  config PHY_SAMSUNG_USB2
> >  	tristate "Samsung USB 2.0 PHY driver"
> >  	depends on HAS_IOMEM
> > diff --git a/drivers/phy/samsung/Makefile
> > b/drivers/phy/samsung/Makefile index db9b1aa0de6e..3959100fe8a2 100644
> > --- a/drivers/phy/samsung/Makefile
> > +++ b/drivers/phy/samsung/Makefile
> > @@ -2,6 +2,7 @@
> >  obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
> >  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
> >  obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
> > +obj-$(CONFIG_PHY_SAMSUNG_UFS)		+= phy-samsung-ufs.o
> >  obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
> >  phy-exynos-usb2-y			+= phy-samsung-usb2.o
> >  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-
> usb2.o
> > diff --git a/drivers/phy/samsung/phy-exynos7-ufs.h
> > b/drivers/phy/samsung/phy-exynos7-ufs.h
> > new file mode 100644
> > index 000000000000..da981c1ac040
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-exynos7-ufs.h
> > @@ -0,0 +1,85 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * UFS PHY driver data for Samsung EXYNOS7 SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + */
> > +#ifndef _PHY_EXYNOS7_UFS_H_
> > +#define _PHY_EXYNOS7_UFS_H_
> > +
> > +#include "phy-samsung-ufs.h"
> > +
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL	0x720
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK	0x1
> > +#define EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN	BIT(0)
> > +
> > +/* Calibration for phy initialization */ static const struct
> > +samsung_ufs_phy_cfg exynos7_pre_init_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_ANY),
> > +	PHY_COMN_REG_CFG(0x017, 0x84, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x035, 0x58, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x037, 0x40, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x03b, 0x83, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x04c, 0x5b, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_ANY),
> > +	PHY_TRSV_REG_CFG(0x05c, 0x14, PWR_MODE_ANY),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +static const struct samsung_ufs_phy_cfg exynos7_post_init_cfg[] = {
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +/* Calibration for HS mode series A/B */ static const struct
> > +samsung_ufs_phy_cfg exynos7_pre_pwr_hs_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x00f, 0xfa, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x010, 0x82, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x011, 0x1e, PWR_MODE_HS_ANY),
> > +	/* Setting order: 1st(0x16, 2nd(0x15) */
> > +	PHY_COMN_REG_CFG(0x016, 0xff, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x015, 0x80, PWR_MODE_HS_ANY),
> > +	PHY_COMN_REG_CFG(0x017, 0x94, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x036, 0x32, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x037, 0x43, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x038, 0x3f, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x042, 0x88, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x042, 0xbb, PWR_MODE_HS_G2_SER_B),
> > +	PHY_TRSV_REG_CFG(0x043, 0xa6, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x048, 0x74, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x034, 0x35, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x034, 0x36, PWR_MODE_HS_G2_SER_B),
> > +	PHY_TRSV_REG_CFG(0x035, 0x5b, PWR_MODE_HS_G2_SER_A),
> > +	PHY_TRSV_REG_CFG(0x035, 0x5c, PWR_MODE_HS_G2_SER_B),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +/* Calibration for HS mode series A/B atfer PMC */ static const
> > +struct samsung_ufs_phy_cfg exynos7_post_pwr_hs_cfg[] = {
> > +	PHY_COMN_REG_CFG(0x015, 0x00, PWR_MODE_HS_ANY),
> > +	PHY_TRSV_REG_CFG(0x04d, 0x83, PWR_MODE_HS_ANY),
> > +	END_UFS_PHY_CFG
> > +};
> > +
> > +static const struct samsung_ufs_phy_cfg
> *exynos7_ufs_phy_cfgs[CFG_TAG_MAX] = {
> > +	[CFG_PRE_INIT]		= exynos7_pre_init_cfg,
> > +	[CFG_POST_INIT]		= exynos7_post_init_cfg,
> > +	[CFG_PRE_PWR_HS]	= exynos7_pre_pwr_hs_cfg,
> > +	[CFG_POST_PWR_HS]	= exynos7_post_pwr_hs_cfg,
> > +};
> > +
> > +static struct samsung_ufs_phy_drvdata exynos7_ufs_phy = {
> > +	.cfg = exynos7_ufs_phy_cfgs,
> > +	.isol = {
> > +		.offset = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL,
> > +		.mask = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_MASK,
> > +		.en = EXYNOS7_EMBEDDED_COMBO_PHY_CTRL_EN,
> > +	},
> > +};
> > +
> > +#endif /* _PHY_EXYNOS7_UFS_H_ */
> > diff --git a/drivers/phy/samsung/phy-samsung-ufs.c
> > b/drivers/phy/samsung/phy-samsung-ufs.c
> > new file mode 100644
> > index 000000000000..2d5db24de49b
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-samsung-ufs.c
> > @@ -0,0 +1,311 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * UFS PHY driver for Samsung SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include <linux/of.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/phy/phy-samsung-ufs.h> #include
> > +<linux/platform_device.h> #include <linux/regmap.h>
> > +
> > +#include "phy-samsung-ufs.h"
> > +
> > +#define for_each_phy_lane(phy, i) \
> > +	for (i = 0; i < (phy)->lane_cnt; i++) #define for_each_phy_cfg(cfg)
> > +\
> > +	for (; (cfg)->id; (cfg)++)
> > +
> > +#define PHY_DEF_LANE_CNT	1
> > +
> > +static void samsung_ufs_phy_config(struct samsung_ufs_phy *phy,
> > +			const struct samsung_ufs_phy_cfg *cfg, u8 lane) {
> > +	enum {LANE_0, LANE_1}; /* lane index */
> > +
> > +	switch (lane) {
> > +	case LANE_0:
> > +		writel(cfg->val, (phy)->reg_pma + cfg->off_0);
> > +		break;
> > +	case LANE_1:
> > +		if (cfg->id == PHY_TRSV_BLK)
> > +			writel(cfg->val, (phy)->reg_pma + cfg->off_1);
> > +		break;
> > +	}
> > +}
> > +
> > +int samsung_ufs_phy_wait_for_lock_acq(struct phy *phy) {
> > +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> > +	const unsigned int timeout_us = 100000;
> > +	const unsigned int sleep_us = 10;
> > +	u32 val;
> > +	int err;
> > +
> > +	err = readl_poll_timeout(
> > +			ufs_phy->reg_pma +
> PHY_APB_ADDR(PHY_PLL_LOCK_STATUS),
> > +			val, (val & PHY_PLL_LOCK_BIT), sleep_us, timeout_us);
> > +	if (err) {
> > +		dev_err(ufs_phy->dev,
> > +			"failed to get phy pll lock acquisition %d\n", err);
> > +		goto out;
> > +	}
> > +
> > +	err = readl_poll_timeout(
> > +			ufs_phy->reg_pma +
> PHY_APB_ADDR(PHY_CDR_LOCK_STATUS),
> > +			val, (val & PHY_CDR_LOCK_BIT), sleep_us, timeout_us);
> > +	if (err) {
> > +		dev_err(ufs_phy->dev,
> > +			"failed to get phy cdr lock acquisition %d\n", err);
> > +		goto out;
> > +	}
> > +
> > +out:
> > +	return err;
> > +}
> > +
> > +int samsung_ufs_phy_calibrate(struct phy *phy) {
> > +	struct samsung_ufs_phy *ufs_phy = get_samsung_ufs_phy(phy);
> > +	struct samsung_ufs_phy_cfg **cfgs = ufs_phy->cfg;
> > +	const struct samsung_ufs_phy_cfg *cfg;
> > +	int i;
> > +	int err = 0;
> > +
> > +	if (unlikely(ufs_phy->ufs_phy_state < CFG_PRE_INIT ||
> > +		     ufs_phy->ufs_phy_state >= CFG_TAG_MAX)) {
> > +		dev_err(ufs_phy->dev, "invalid phy config index %d\n",
> > +							ufs_phy-
> >ufs_phy_state);
> > +		return -EINVAL;
> > +	}
> > +
> > +	if (ufs_phy->is_pre_init)
> > +		ufs_phy->is_pre_init = false;
> > +	if (ufs_phy->is_post_init) {
> > +		ufs_phy->is_post_init = false;
> > +		ufs_phy->ufs_phy_state = CFG_POST_INIT;
> > +	}
> > +	if (ufs_phy->is_pre_pmc) {
> > +		ufs_phy->is_pre_pmc = false;
> > +		ufs_phy->ufs_phy_state = CFG_PRE_PWR_HS;
> > +	}
> > +	if (ufs_phy->is_post_pmc) {
> > +		ufs_phy->is_post_pmc = false;
> > +		ufs_phy->ufs_phy_state = CFG_POST_PWR_HS;
> > +	}
> > +
> > +	switch (ufs_phy->ufs_phy_state) {
> > +	case CFG_PRE_INIT:
> > +		ufs_phy->is_post_init = true;
> > +		break;
> > +	case CFG_POST_INIT:
> > +		ufs_phy->is_pre_pmc = true;
> > +		break;
> > +	case CFG_PRE_PWR_HS:
> > +		ufs_phy->is_post_pmc = true;
> > +		break;
> > +	case CFG_POST_PWR_HS:
> > +		break;
> > +	default:
> > +		dev_err(ufs_phy->dev, "wrong state for phy calibration\n");
> > +	}
> > +
> > +	cfg = cfgs[ufs_phy->ufs_phy_state];
> > +	if (!cfg)
> > +		goto out;
> > +
> > +	for_each_phy_cfg(cfg) {
> > +		for_each_phy_lane(ufs_phy, i) {
> > +			samsung_ufs_phy_config(ufs_phy, cfg, i);
> > +		}
> > +	}
> > +
> > +	if (ufs_phy->ufs_phy_state == CFG_POST_PWR_HS)
> > +		err = samsung_ufs_phy_wait_for_lock_acq(phy);
> > +out:
> > +	return err;
> > +}
> > +
> > +static int samsung_ufs_phy_clks_init(struct samsung_ufs_phy *phy) {
> > +	struct clk *child, *parent;
> > +
> > +	child = devm_clk_get(phy->dev, "ref_clk");
> > +	if (IS_ERR(child))
> > +		dev_err(phy->dev, "failed to get ref_clk clock\n");
> > +	else
> > +		phy->ref_clk = child;
> > +
> > +	parent = devm_clk_get(phy->dev, "ref_clk_parent");
> > +	if (IS_ERR(parent))
> > +		dev_err(phy->dev, "failed to get ref_clk_parent clock\n");
> > +	else
> > +		phy->ref_clk_parent = parent;
> > +
> > +	return clk_set_parent(child, parent); }
> > +
> > +static int samsung_ufs_phy_init(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +
> > +	_phy->lane_cnt = phy->attrs.bus_width;
> > +	_phy->ufs_phy_state = CFG_PRE_INIT;
> > +
> > +	_phy->is_pre_init = true;
> > +	_phy->is_post_init = false;
> > +	_phy->is_pre_pmc = false;
> > +	_phy->is_post_pmc = false;
> > +
> > +	samsung_ufs_phy_clks_init(_phy);
> > +
> > +	samsung_ufs_phy_calibrate(phy);
> > +
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_power_on(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +	int ret;
> > +
> > +	ret = clk_prepare_enable(_phy->ref_clk);
> > +	if (ret) {
> > +		dev_err(_phy->dev, "%s: ref_clk enable failed %d\n",
> > +				__func__, ret);
> > +		return ret;
> > +	}
> > +
> > +	samsung_ufs_phy_ctrl_isol(_phy, false);
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_power_off(struct phy *phy) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(phy);
> > +
> > +	samsung_ufs_phy_ctrl_isol(_phy, true);
> > +	clk_disable_unprepare(_phy->ref_clk);
> > +	return 0;
> > +}
> > +
> > +static int samsung_ufs_phy_set_mode(struct phy *generic_phy,
> > +					enum phy_mode mode, int submode) {
> > +	struct samsung_ufs_phy *_phy = get_samsung_ufs_phy(generic_phy);
> > +
> > +	_phy->mode = PHY_MODE_INVALID;
> > +
> > +	if (mode > 0)
> > +		_phy->mode = mode;
> > +
> > +	return 0;
> > +}
> > +
> > +static struct phy_ops samsung_ufs_phy_ops = {
> > +	.init		= samsung_ufs_phy_init,
> > +	.power_on	= samsung_ufs_phy_power_on,
> > +	.power_off	= samsung_ufs_phy_power_off,
> > +	.calibrate	= samsung_ufs_phy_calibrate,
> > +	.set_mode	= samsung_ufs_phy_set_mode,
> > +}
> > +;
> > +static const struct of_device_id samsung_ufs_phy_match[];
> > +
> > +static int samsung_ufs_phy_probe(struct platform_device *pdev) {
> > +	struct device *dev = &pdev->dev;
> > +	struct resource *res;
> > +	const struct of_device_id *match;
> > +	struct samsung_ufs_phy *phy;
> > +	struct phy *gen_phy;
> > +	struct phy_provider *phy_provider;
> > +	const struct samsung_ufs_phy_drvdata *drvdata;
> > +	int err = 0;
> > +
> > +	match = of_match_node(samsung_ufs_phy_match, dev->of_node);
> > +	if (!match) {
> > +		err = -EINVAL;
> > +		dev_err(dev, "failed to get match_node\n");
> > +		goto out;
> > +	}
> > +
> > +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> > +	if (!phy) {
> > +		err = -ENOMEM;
> > +		goto out;
> > +	}
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "phy-
> pma");
> > +	phy->reg_pma = devm_ioremap_resource(dev, res);
> > +	if (IS_ERR(phy->reg_pma)) {
> > +		err = PTR_ERR(phy->reg_pma);
> > +		goto out;
> > +	}
> > +
> > +	phy->reg_pmu = syscon_regmap_lookup_by_phandle(
> > +				dev->of_node, "samsung,pmu-syscon");
> > +	if (IS_ERR(phy->reg_pmu)) {
> > +		err = PTR_ERR(phy->reg_pmu);
> > +		dev_err(dev, "failed syscon remap for pmu\n");
> > +		goto out;
> > +	}
> > +
> > +	gen_phy = devm_phy_create(dev, NULL, &samsung_ufs_phy_ops);
> > +	if (IS_ERR(gen_phy)) {
> > +		err = PTR_ERR(gen_phy);
> > +		dev_err(dev, "failed to create PHY for ufs-phy\n");
> > +		goto out;
> > +	}
> > +
> > +	drvdata = match->data;
> > +	phy->dev = dev;
> > +	phy->drvdata = drvdata;
> > +	phy->cfg = (struct samsung_ufs_phy_cfg **)drvdata->cfg;
> > +	phy->isol = &drvdata->isol;
> > +	phy->lane_cnt = PHY_DEF_LANE_CNT;
> > +
> > +	phy_set_drvdata(gen_phy, phy);
> > +
> > +	phy_provider = devm_of_phy_provider_register(dev,
> of_phy_simple_xlate);
> > +	if (IS_ERR(phy_provider)) {
> > +		err = PTR_ERR(phy_provider);
> > +		dev_err(dev, "failed to register phy-provider\n");
> > +		goto out;
> > +	}
> > +out:
> > +	return err;
> > +}
> > +
> > +static const struct of_device_id samsung_ufs_phy_match[] = {
> > +	{
> > +		.compatible = "samsung,exynos7-ufs-phy",
> > +		.data = &exynos7_ufs_phy,
> > +	},
> > +	{},
> > +};
> > +MODULE_DEVICE_TABLE(of, samsung_ufs_phy_match);
> > +
> > +static struct platform_driver samsung_ufs_phy_driver = {
> > +	.probe  = samsung_ufs_phy_probe,
> > +	.driver = {
> > +		.name = "samsung-ufs-phy",
> > +		.of_match_table = samsung_ufs_phy_match,
> > +	},
> > +};
> > +module_platform_driver(samsung_ufs_phy_driver);
> > +MODULE_DESCRIPTION("Samsung SoC UFS PHY Driver");
> > +MODULE_AUTHOR("Seungwon Jeon <essuuj@gmail.com>");
> > +MODULE_AUTHOR("Alim Akhtar <alim.akhtar@samsung.com>");
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/phy/samsung/phy-samsung-ufs.h
> > b/drivers/phy/samsung/phy-samsung-ufs.h
> > new file mode 100644
> > index 000000000000..d0ae2b416b2b
> > --- /dev/null
> > +++ b/drivers/phy/samsung/phy-samsung-ufs.h
> > @@ -0,0 +1,100 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * UFS PHY driver for Samsung EXYNOS SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +#ifndef _PHY_SAMSUNG_UFS_
> > +#define _PHY_SAMSUNG_UFS_
> > +
> > +#define PHY_COMN_BLK	1
> > +#define PHY_TRSV_BLK	2
> > +#define END_UFS_PHY_CFG { 0 }
> > +#define PHY_TRSV_CH_OFFSET	0x30
> > +#define PHY_APB_ADDR(off)	((off) << 2)
> > +
> > +#define PHY_COMN_REG_CFG(o, v, d) {	\
> > +	.off_0 = PHY_APB_ADDR((o)),	\
> > +	.off_1 = 0,		\
> > +	.val = (v),		\
> > +	.desc = (d),		\
> > +	.id = PHY_COMN_BLK,	\
> > +}
> > +
> > +#define PHY_TRSV_REG_CFG(o, v, d) {	\
> > +	.off_0 = PHY_APB_ADDR((o)),	\
> > +	.off_1 = PHY_APB_ADDR((o) + PHY_TRSV_CH_OFFSET),	\
> > +	.val = (v),		\
> > +	.desc = (d),		\
> > +	.id = PHY_TRSV_BLK,	\
> > +}
> > +
> > +/* UFS PHY registers */
> > +#define PHY_PLL_LOCK_STATUS	0x1e
> > +#define PHY_CDR_LOCK_STATUS	0x5e
> > +
> > +#define PHY_PLL_LOCK_BIT	BIT(5)
> > +#define PHY_CDR_LOCK_BIT	BIT(4)
> > +
> > +/* PHY calibration point/state */
> > +enum {
> > +	CFG_PRE_INIT,
> > +	CFG_POST_INIT,
> > +	CFG_PRE_PWR_HS,
> > +	CFG_POST_PWR_HS,
> > +	CFG_TAG_MAX,
> > +};
> > +
> > +struct samsung_ufs_phy_cfg {
> > +	u32 off_0;
> > +	u32 off_1;
> > +	u32 val;
> > +	u8 desc;
> > +	u8 id;
> > +};
> > +
> > +struct samsung_ufs_phy_drvdata {
> > +	const struct samsung_ufs_phy_cfg **cfg;
> > +	struct pmu_isol {
> > +		u32 offset;
> > +		u32 mask;
> > +		u32 en;
> > +	} isol;
> > +};
> > +
> > +struct samsung_ufs_phy {
> > +	struct device *dev;
> > +	void __iomem *reg_pma;
> > +	struct regmap *reg_pmu;
> > +	struct clk *ref_clk;
> > +	struct clk *ref_clk_parent;
> > +	const struct samsung_ufs_phy_drvdata *drvdata;
> > +	struct samsung_ufs_phy_cfg **cfg;
> > +	const struct pmu_isol *isol;
> > +	u8 lane_cnt;
> > +	int ufs_phy_state;
> > +	enum phy_mode mode;
> > +	bool is_pre_init;
> > +	bool is_post_init;
> > +	bool is_pre_pmc;
> > +	bool is_post_pmc;
> > +};
> > +
> > +static inline struct samsung_ufs_phy *get_samsung_ufs_phy(struct phy
> > +*phy) {
> > +	return (struct samsung_ufs_phy *)phy_get_drvdata(phy); }
> > +
> > +static inline void samsung_ufs_phy_ctrl_isol(
> > +		struct samsung_ufs_phy *phy, u32 isol) {
> > +	regmap_update_bits(phy->reg_pmu, phy->isol->offset,
> > +			phy->isol->mask, isol ? 0 : phy->isol->en); }
> > +
> > +#include "phy-exynos7-ufs.h"
> > +
> > +#endif /* _PHY_SAMSUNG_UFS_ */
> > diff --git a/include/linux/phy/phy-samsung-ufs.h
> > b/include/linux/phy/phy-samsung-ufs.h
> > new file mode 100644
> > index 000000000000..1def56207f5d
> > --- /dev/null
> > +++ b/include/linux/phy/phy-samsung-ufs.h
> > @@ -0,0 +1,70 @@
> > +/* SPDX-License-Identifier: GPL-2.0-only */
> > +/*
> > + * phy-samsung-ufs.h - Header file for the UFS PHY of Samsung SoC
> > + *
> > + * Copyright (C) 2015 Samsung Electronics Co., Ltd.
> > + * Author: Seungwon Jeon <essuuj@gmail.com>
> > + * Author: Alim Akhtar <alim.akhtar@samsung.com>
> > + *
> > + */
> > +
> > +#ifndef _PHY_EXYNOS_UFS_H_
> > +#define _PHY_EXYNOS_UFS_H_
> > +
> > +#include "phy.h"
> > +
> > +/* description for PHY calibration */ enum {
> > +	/* applicable to any */
> > +	PWR_DESC_ANY	= 0,
> > +	/* mode */
> > +	PWR_DESC_PWM	= 1,
> > +	PWR_DESC_HS	= 2,
> > +	/* series */
> > +	PWR_DESC_SER_A	= 1,
> > +	PWR_DESC_SER_B	= 2,
> > +	/* gear */
> > +	PWR_DESC_G1	= 1,
> > +	PWR_DESC_G2	= 2,
> > +	PWR_DESC_G3	= 3,
> > +	PWR_DESC_G4	= 4,
> > +	PWR_DESC_G5	= 5,
> > +	PWR_DESC_G6	= 6,
> > +	PWR_DESC_G7	= 7,
> > +	/* field mask */
> > +	MD_MASK		= 0x3,
> > +	SR_MASK		= 0x3,
> > +	GR_MASK		= 0x7,
> > +};
> > +
> > +#define PWR_MODE(g, s, m)	((((g) & GR_MASK) << 4) |\
> > +				 (((s) & SR_MASK) << 2) | ((m) & MD_MASK))
> > +#define PWR_MODE_HS(g, s)	((((g) & GR_MASK) << 4) |\
> > +				 (((s) & SR_MASK) << 2) | PWR_DESC_HS)
> > +#define PWR_MODE_HS_G1_ANY	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G1_SER_A	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G1_SER_B	PWR_MODE_HS(PWR_DESC_G1,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_G2_ANY	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G2_SER_A	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G2_SER_B	PWR_MODE_HS(PWR_DESC_G2,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_G3_ANY	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_ANY)
> > +#define PWR_MODE_HS_G3_SER_A	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_SER_A)
> > +#define PWR_MODE_HS_G3_SER_B	PWR_MODE_HS(PWR_DESC_G3,
> PWR_DESC_SER_B)
> > +#define PWR_MODE_HS_ANY
> 	PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_HS)
> > +#define PWR_MODE_PWM_ANY	PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_PWM)
> > +#define PWR_MODE_ANY		PWR_MODE(PWR_DESC_ANY,\
> > +					 PWR_DESC_ANY, PWR_DESC_ANY)
> > +#define IS_PWR_MODE_HS(d)	(((d) & MD_MASK) == PWR_DESC_HS)
> > +#define IS_PWR_MODE_PWM(d)	(((d) & MD_MASK) ==
> PWR_DESC_PWM)
> > +#define IS_PWR_MODE_ANY(d)	((d) == PWR_MODE_ANY)
> > +#define IS_PWR_MODE_HS_ANY(d)	((d) == PWR_MODE_HS_ANY)
> > +#define COMP_PWR_MODE(a, b)		((a) == (b))
> > +#define COMP_PWR_MODE_GEAR(a, b)	((((a) >> 4) & GR_MASK) == \
> > +					 (((b) >> 4) & GR_MASK))
> > +#define COMP_PWR_MODE_SER(a, b)		((((a) >> 2) & SR_MASK)
> == \
> > +					 (((b) >> 2) & SR_MASK))
> > +#define COMP_PWR_MODE_MD(a, b)		(((a) & MD_MASK) ==
> ((b) & MD_MASK))
> > +
> > +#endif /* _PHY_EXYNOS_UFS_H_ */
> >


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Alim Akhtar]

Hello Pawel
Thanks for helping in testing.

> -----Original Message-----
> From: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> Sent: 20 March 2020 01:12
> To: Alim Akhtar <alim.akhtar@samsung.com>
> Cc: krzk@kernel.org; avri.altman@wdc.com; martin.petersen@oracle.com;
> kwmad.kim@samsung.com; stanley.chu@mediatek.com;
> cang@codeaurora.org; linux-samsung-soc@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Subject: Re: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI
> 
> On Thu, 2020-03-19 at 20:30 +0530, Alim Akhtar wrote:
> > This patch-set introduces UFS (Universal Flash Storage) host
> > controller support for Samsung family SoC. Mostly, it consists of UFS PHY and
> host specific driver.
> >
> > - Changes since v2:
> > * fixed build warning by kbuild test robot
> > * Added Reported-by tags
> >
> > - Changes since v1:
> > * fixed make dt_binding_check error as pointed by Rob
> > * Addressed Krzysztof's review comments
> > * Added Reviewed-by tags
> >
> >
> > patch 1/5: define devicetree bindings for UFS PHY patch 2/5: Adds UFS
> > PHY driver patch 3/5: define devicetree bindings for UFS HCI patch
> > 4/5: Adds Samsung UFS HCI driver patch 5/5: Enabled UFS on exynos7
> > platform
> Hi
> Is this compatible with Exynos7420? Looking at u-boot source code, there is
> Espresso7420 - isn't it the same device? Also this driver looks very similar to the
> one from vendor kernel sources (for my device).
> 
Exynos7 and Exynos7420 are compatible and belong to same Exynos SoC series (but there are some fine differences)

> I did tried to run this on my Exynos7420 based device (Samsung S6 Edge
> phone) with 5.6-rc6, to get any storage working (since it doesn't have sdcard
> slot).
> 
I think this should work on S6 Edge, but not entirely sure, as I am not aware of the S6 H/W schematic, specially PMIC connection.

> At first i got error in exynos_ufs_config_smu. Looking at vendor sources, on my
> device only secureos is able to write to those registers so i fixed it by using smc
> calls and driver probes fine. Will this be also supported by driver (maybe in
> future)?
> 
> But now got another error
> [    1.610464] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.610629] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.610747] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.610863] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.614727] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.621061] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.627396] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.633730] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.640065] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.646400] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.652734] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    1.747649] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.747807] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.747924] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.748041] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.751909] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.758244] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.764578] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.770913] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.777248] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.783582] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.789917] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    1.884841] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.884999] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.885116] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.885233] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.889100] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.895435] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.901770] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.908104] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.914439] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.920773] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.927108] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    2.998155] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    4.502138] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    6.006137] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    6.006311] exynos-ufshc 15570000.ufs: ufshcd_query_flag_retry:
> query attribute, opcode 5, idn 1, failed with error -11 after 3 retires
> [    6.006545] exynos-ufshc 15570000.ufs: ufshcd_complete_dev_init
> reading fDeviceInit flag failed with error -11
> 
> Do You have any idea what could be wrong?
> 
To me, It looks like UFS device is not powered ON or properly Reseted, I have seen this kind of issues in past and 
AFAIR, fix was to keep the PMIC rail which was hook to device RESET_N always-on.

> Thanks 
> >
> > Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)
> >
> >
> > Alim Akhtar (5):
> >   dt-bindings: phy: Document Samsung UFS PHY bindings
> >   phy: samsung-ufs: add UFS PHY driver for samsung SoC
> >   Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
> >     controller
> >   scsi: ufs-exynos: add UFS host support for Exynos SoCs
> >   arm64: dts: Add node for ufs exynos7
> >
> >  .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
> >  .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
> >  .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
> >  arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
> >  drivers/phy/samsung/Kconfig                   |    9 +
> >  drivers/phy/samsung/Makefile                  |    1 +
> >  drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
> >  drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
> >  drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
> >  drivers/scsi/ufs/Kconfig                      |   12 +
> >  drivers/scsi/ufs/Makefile                     |    1 +
> >  drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
> >  drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
> >  drivers/scsi/ufs/unipro.h                     |   41 +
> >  include/linux/phy/phy-samsung-ufs.h           |   70 +
> >  15 files changed, 2521 insertions(+), 2 deletions(-)  create mode
> > 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> >  create mode 100644
> > Documentation/devicetree/bindings/ufs/ufs-exynos.txt
> >  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
> >  create mode 100644 drivers/scsi/ufs/ufs-exynos.c  create mode 100644
> > drivers/scsi/ufs/ufs-exynos.h  create mode 100644
> > include/linux/phy/phy-samsung-ufs.h
> >

RE: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI

[Alim Akhtar]

Hello Pawel
Thanks for helping in testing.

> -----Original Message-----
> From: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> Sent: 20 March 2020 01:12
> To: Alim Akhtar <alim.akhtar@samsung.com>
> Cc: krzk@kernel.org; avri.altman@wdc.com; martin.petersen@oracle.com;
> kwmad.kim@samsung.com; stanley.chu@mediatek.com;
> cang@codeaurora.org; linux-samsung-soc@vger.kernel.org; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Subject: Re: [PATCH v3 0/5] exynos-ufs: Add support for UFS HCI
> 
> On Thu, 2020-03-19 at 20:30 +0530, Alim Akhtar wrote:
> > This patch-set introduces UFS (Universal Flash Storage) host
> > controller support for Samsung family SoC. Mostly, it consists of UFS PHY and
> host specific driver.
> >
> > - Changes since v2:
> > * fixed build warning by kbuild test robot
> > * Added Reported-by tags
> >
> > - Changes since v1:
> > * fixed make dt_binding_check error as pointed by Rob
> > * Addressed Krzysztof's review comments
> > * Added Reviewed-by tags
> >
> >
> > patch 1/5: define devicetree bindings for UFS PHY patch 2/5: Adds UFS
> > PHY driver patch 3/5: define devicetree bindings for UFS HCI patch
> > 4/5: Adds Samsung UFS HCI driver patch 5/5: Enabled UFS on exynos7
> > platform
> Hi
> Is this compatible with Exynos7420? Looking at u-boot source code, there is
> Espresso7420 - isn't it the same device? Also this driver looks very similar to the
> one from vendor kernel sources (for my device).
> 
Exynos7 and Exynos7420 are compatible and belong to same Exynos SoC series (but there are some fine differences)

> I did tried to run this on my Exynos7420 based device (Samsung S6 Edge
> phone) with 5.6-rc6, to get any storage working (since it doesn't have sdcard
> slot).
> 
I think this should work on S6 Edge, but not entirely sure, as I am not aware of the S6 H/W schematic, specially PMIC connection.

> At first i got error in exynos_ufs_config_smu. Looking at vendor sources, on my
> device only secureos is able to write to those registers so i fixed it by using smc
> calls and driver probes fine. Will this be also supported by driver (maybe in
> future)?
> 
> But now got another error
> [    1.610464] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.610629] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.610747] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.610863] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.614727] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.621061] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.627396] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.633730] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.640065] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.646400] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.652734] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    1.747649] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.747807] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.747924] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.748041] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.751909] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.758244] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.764578] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.770913] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.777248] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.783582] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.789917] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    1.884841] exynos-ufshc 15570000.ufs: ufshcd_intr: Unhandled
> interrupt 0x00000000
> [    1.884999] host_regs: 00000000: 0383ff0f 00000000 00000200 00000000
> [    1.885116] host_regs: 00000010: 00000101 00007fce 00000000 00000000
> [    1.885233] host_regs: 00000020: 00000000 00030e75 00000000 00000000
> [    1.889100] host_regs: 00000030: 0000000f 00000000 00000000 00000000
> [    1.895435] host_regs: 00000040: 00000000 00000000 00000000 00000000
> [    1.901770] host_regs: 00000050: f8c37000 00000000 00000001 00000000
> [    1.908104] host_regs: 00000060: 00000001 00000000 00000000 00000000
> [    1.914439] host_regs: 00000070: f9644000 00000000 00000000 00000000
> [    1.920773] host_regs: 00000080: 00000001 00000000 00000000 00000000
> [    1.927108] host_regs: 00000090: 00000002 95290000 00000000 00000000
> [    2.998155] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    4.502138] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    6.006137] exynos-ufshc 15570000.ufs: ufshcd_query_flag: Sending
> flag query for idn 1 failed, err = -11
> [    6.006311] exynos-ufshc 15570000.ufs: ufshcd_query_flag_retry:
> query attribute, opcode 5, idn 1, failed with error -11 after 3 retires
> [    6.006545] exynos-ufshc 15570000.ufs: ufshcd_complete_dev_init
> reading fDeviceInit flag failed with error -11
> 
> Do You have any idea what could be wrong?
> 
To me, It looks like UFS device is not powered ON or properly Reseted, I have seen this kind of issues in past and 
AFAIR, fix was to keep the PMIC rail which was hook to device RESET_N always-on.

> Thanks 
> >
> > Note: This series is based on Linux-5.6-rc6 (commit: fb33c6510d55)
> >
> >
> > Alim Akhtar (5):
> >   dt-bindings: phy: Document Samsung UFS PHY bindings
> >   phy: samsung-ufs: add UFS PHY driver for samsung SoC
> >   Documentation: devicetree: ufs: Add DT bindings for exynos UFS host
> >     controller
> >   scsi: ufs-exynos: add UFS host support for Exynos SoCs
> >   arm64: dts: Add node for ufs exynos7
> >
> >  .../bindings/phy/samsung,ufs-phy.yaml         |   62 +
> >  .../devicetree/bindings/ufs/ufs-exynos.txt    |  104 ++
> >  .../boot/dts/exynos/exynos7-espresso.dts      |   16 +
> >  arch/arm64/boot/dts/exynos/exynos7.dtsi       |   44 +-
> >  drivers/phy/samsung/Kconfig                   |    9 +
> >  drivers/phy/samsung/Makefile                  |    1 +
> >  drivers/phy/samsung/phy-exynos7-ufs.h         |   85 +
> >  drivers/phy/samsung/phy-samsung-ufs.c         |  311 ++++
> >  drivers/phy/samsung/phy-samsung-ufs.h         |  100 ++
> >  drivers/scsi/ufs/Kconfig                      |   12 +
> >  drivers/scsi/ufs/Makefile                     |    1 +
> >  drivers/scsi/ufs/ufs-exynos.c                 | 1399 +++++++++++++++++
> >  drivers/scsi/ufs/ufs-exynos.h                 |  268 ++++
> >  drivers/scsi/ufs/unipro.h                     |   41 +
> >  include/linux/phy/phy-samsung-ufs.h           |   70 +
> >  15 files changed, 2521 insertions(+), 2 deletions(-)  create mode
> > 100644 Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml
> >  create mode 100644
> > Documentation/devicetree/bindings/ufs/ufs-exynos.txt
> >  create mode 100644 drivers/phy/samsung/phy-exynos7-ufs.h
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.c
> >  create mode 100644 drivers/phy/samsung/phy-samsung-ufs.h
> >  create mode 100644 drivers/scsi/ufs/ufs-exynos.c  create mode 100644
> > drivers/scsi/ufs/ufs-exynos.h  create mode 100644
> > include/linux/phy/phy-samsung-ufs.h
> >




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Avri Altman]

> +static int exynos7_ufs_pre_link(struct exynos_ufs *ufs)
> +{
> +       struct ufs_hba *hba = ufs->hba;
> +       u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
Can pa_dbg_option_suite be replaced by a macro?

> +       exynos_ufs_disable_ov_tm(hba);
> +
> +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> 0xf);
> +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> 0xf);
A typo? Set PA_DBG_OPTION_SUITE_DYN twice? 

> +#define PWR_MODE_STR_LEN       64
> +static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
> +                               struct ufs_pa_layer_attr *pwr_max,
> +                               struct ufs_pa_layer_attr *pwr_req)
> +{
> +       struct exynos_ufs *ufs = ufshcd_get_variant(hba);
> +       struct phy *generic_phy = ufs->phy;
> +       struct uic_pwr_mode *pwr = &ufs->pwr_act;
> +       char pwr_str[PWR_MODE_STR_LEN] = "";
Un-needed complication IMO - all those snprintf that is. 

> +
> +static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs)
> +{
> +       const u8 cntr_div = 40;
Can be replaced by a macro?

> +struct exynos_ufs_drv_data exynos_ufs_drvs = {
> +
> +       .compatible             = "samsung,exynos7-ufs",
> +       .uic_attr               = &exynos7_uic_attr,
> +       .quirks                 = UFSHCD_QUIRK_PRDT_BYTE_GRAN |
> +                                 UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
> +                                 UFSHCI_QUIRK_BROKEN_HCE |
> +                                 UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
> +       .opts                   = EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
> +                                 EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
> +                                 EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
In what way opts are different from quirks?


Thanks,
Avri

RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Avri Altman]

> +static int exynos7_ufs_pre_link(struct exynos_ufs *ufs)
> +{
> +       struct ufs_hba *hba = ufs->hba;
> +       u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
Can pa_dbg_option_suite be replaced by a macro?

> +       exynos_ufs_disable_ov_tm(hba);
> +
> +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> 0xf);
> +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> 0xf);
A typo? Set PA_DBG_OPTION_SUITE_DYN twice? 

> +#define PWR_MODE_STR_LEN       64
> +static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
> +                               struct ufs_pa_layer_attr *pwr_max,
> +                               struct ufs_pa_layer_attr *pwr_req)
> +{
> +       struct exynos_ufs *ufs = ufshcd_get_variant(hba);
> +       struct phy *generic_phy = ufs->phy;
> +       struct uic_pwr_mode *pwr = &ufs->pwr_act;
> +       char pwr_str[PWR_MODE_STR_LEN] = "";
Un-needed complication IMO - all those snprintf that is. 

> +
> +static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs)
> +{
> +       const u8 cntr_div = 40;
Can be replaced by a macro?

> +struct exynos_ufs_drv_data exynos_ufs_drvs = {
> +
> +       .compatible             = "samsung,exynos7-ufs",
> +       .uic_attr               = &exynos7_uic_attr,
> +       .quirks                 = UFSHCD_QUIRK_PRDT_BYTE_GRAN |
> +                                 UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
> +                                 UFSHCI_QUIRK_BROKEN_HCE |
> +                                 UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
> +       .opts                   = EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
> +                                 EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
> +                                 EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
In what way opts are different from quirks?


Thanks,
Avri
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Alim Akhtar]

Hi Avri
Thanks for review, see my comment inline below

> -----Original Message-----
> From: Avri Altman <Avri.Altman@wdc.com>
> Sent: 22 March 2020 17:54
> To: Alim Akhtar <alim.akhtar@samsung.com>; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Cc: krzk@kernel.org; martin.petersen@oracle.com; kwmad.kim@samsung.com;
> stanley.chu@mediatek.com; cang@codeaurora.org; linux-samsung-
> soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-
> kernel@vger.kernel.org
> Subject: RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos
> SoCs
> 
> > +static int exynos7_ufs_pre_link(struct exynos_ufs *ufs) {
> > +       struct ufs_hba *hba = ufs->hba;
> > +       u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
> Can pa_dbg_option_suite be replaced by a macro?
> 
Going forward, I have plan to add multiple Samsung/Exynos SoC variants, which will have its own drv_data. For that reason I kept it.
Let me have a relook on this.

> > +       exynos_ufs_disable_ov_tm(hba);
> > +
> > +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> > 0xf);
> > +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> > 0xf);
> A typo? Set PA_DBG_OPTION_SUITE_DYN twice?
> 
Ack, will change

> > +#define PWR_MODE_STR_LEN       64
> > +static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
> > +                               struct ufs_pa_layer_attr *pwr_max,
> > +                               struct ufs_pa_layer_attr *pwr_req) {
> > +       struct exynos_ufs *ufs = ufshcd_get_variant(hba);
> > +       struct phy *generic_phy = ufs->phy;
> > +       struct uic_pwr_mode *pwr = &ufs->pwr_act;
> > +       char pwr_str[PWR_MODE_STR_LEN] = "";
> Un-needed complication IMO - all those snprintf that is.
> 
You mean pwr_str initialization is not needed here?

> > +
> > +static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs) {
> > +       const u8 cntr_div = 40;
> Can be replaced by a macro?
> 
Sure, will change.

> > +struct exynos_ufs_drv_data exynos_ufs_drvs = {
> > +
> > +       .compatible             = "samsung,exynos7-ufs",
> > +       .uic_attr               = &exynos7_uic_attr,
> > +       .quirks                 = UFSHCD_QUIRK_PRDT_BYTE_GRAN |
> > +                                 UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
> > +                                 UFSHCI_QUIRK_BROKEN_HCE |
> > +                                 UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
> > +       .opts                   = EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
> > +                                 EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
> > +                                 EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
> In what way opts are different from quirks?
> 
Similar to quirks, but only specific to controller local control, like related to APB interface and clock control.
These doesn't need a change in common ufshcd core. So kept as opts.
Will fix your comments and submit v4 soon.
Thanks.
> 
> Thanks,
> Avri

RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos SoCs

[Alim Akhtar]

Hi Avri
Thanks for review, see my comment inline below

> -----Original Message-----
> From: Avri Altman <Avri.Altman@wdc.com>
> Sent: 22 March 2020 17:54
> To: Alim Akhtar <alim.akhtar@samsung.com>; robh+dt@kernel.org;
> devicetree@vger.kernel.org; linux-scsi@vger.kernel.org
> Cc: krzk@kernel.org; martin.petersen@oracle.com; kwmad.kim@samsung.com;
> stanley.chu@mediatek.com; cang@codeaurora.org; linux-samsung-
> soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux-
> kernel@vger.kernel.org
> Subject: RE: [PATCH v3 4/5] scsi: ufs-exynos: add UFS host support for Exynos
> SoCs
> 
> > +static int exynos7_ufs_pre_link(struct exynos_ufs *ufs) {
> > +       struct ufs_hba *hba = ufs->hba;
> > +       u32 val = ufs->drv_data->uic_attr->pa_dbg_option_suite;
> Can pa_dbg_option_suite be replaced by a macro?
> 
Going forward, I have plan to add multiple Samsung/Exynos SoC variants, which will have its own drv_data. For that reason I kept it.
Let me have a relook on this.

> > +       exynos_ufs_disable_ov_tm(hba);
> > +
> > +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> > 0xf);
> > +       ufshcd_dme_set(hba, UIC_ARG_MIB(PA_DBG_OPTION_SUITE_DYN),
> > 0xf);
> A typo? Set PA_DBG_OPTION_SUITE_DYN twice?
> 
Ack, will change

> > +#define PWR_MODE_STR_LEN       64
> > +static int exynos_ufs_post_pwr_mode(struct ufs_hba *hba,
> > +                               struct ufs_pa_layer_attr *pwr_max,
> > +                               struct ufs_pa_layer_attr *pwr_req) {
> > +       struct exynos_ufs *ufs = ufshcd_get_variant(hba);
> > +       struct phy *generic_phy = ufs->phy;
> > +       struct uic_pwr_mode *pwr = &ufs->pwr_act;
> > +       char pwr_str[PWR_MODE_STR_LEN] = "";
> Un-needed complication IMO - all those snprintf that is.
> 
You mean pwr_str initialization is not needed here?

> > +
> > +static void exynos_ufs_fit_aggr_timeout(struct exynos_ufs *ufs) {
> > +       const u8 cntr_div = 40;
> Can be replaced by a macro?
> 
Sure, will change.

> > +struct exynos_ufs_drv_data exynos_ufs_drvs = {
> > +
> > +       .compatible             = "samsung,exynos7-ufs",
> > +       .uic_attr               = &exynos7_uic_attr,
> > +       .quirks                 = UFSHCD_QUIRK_PRDT_BYTE_GRAN |
> > +                                 UFSHCI_QUIRK_BROKEN_REQ_LIST_CLR |
> > +                                 UFSHCI_QUIRK_BROKEN_HCE |
> > +                                 UFSHCI_QUIRK_SKIP_RESET_INTR_AGGR,
> > +       .opts                   = EXYNOS_UFS_OPT_HAS_APB_CLK_CTRL |
> > +                                 EXYNOS_UFS_OPT_BROKEN_AUTO_CLK_CTRL |
> > +                                 EXYNOS_UFS_OPT_BROKEN_RX_SEL_IDX,
> In what way opts are different from quirks?
> 
Similar to quirks, but only specific to controller local control, like related to APB interface and clock control.
These doesn't need a change in common ufshcd core. So kept as opts.
Will fix your comments and submit v4 soon.
Thanks.
> 
> Thanks,
> Avri


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel