* [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs
[not found] <1599584848-15530-1-git-send-email-tdas@codeaurora.org>
@ 2020-09-08 17:07 ` Taniya Das
2020-09-08 17:07 ` [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings Taniya Das
` (4 subsequent siblings)
5 siblings, 0 replies; 9+ messages in thread
From: Taniya Das @ 2020-09-08 17:07 UTC (permalink / raw)
To: Stephen Boyd, Michael Turquette
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
Add programming sequence support for managing the Agera PLLs.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 82 ++++++++++++++++++++++++++++++++++++++++
drivers/clk/qcom/clk-alpha-pll.h | 4 ++
2 files changed, 86 insertions(+)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 26139ef..fb27fcf 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -116,6 +116,16 @@ const u8 clk_alpha_pll_regs[][PLL_OFF_MAX_REGS] = {
[PLL_OFF_OPMODE] = 0x38,
[PLL_OFF_ALPHA_VAL] = 0x40,
},
+ [CLK_ALPHA_PLL_TYPE_AGERA] = {
+ [PLL_OFF_L_VAL] = 0x04,
+ [PLL_OFF_ALPHA_VAL] = 0x08,
+ [PLL_OFF_USER_CTL] = 0x0c,
+ [PLL_OFF_CONFIG_CTL] = 0x10,
+ [PLL_OFF_CONFIG_CTL_U] = 0x14,
+ [PLL_OFF_TEST_CTL] = 0x18,
+ [PLL_OFF_TEST_CTL_U] = 0x1c,
+ [PLL_OFF_STATUS] = 0x2c,
+ },
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
@@ -1561,3 +1571,75 @@ const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
.set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_lucid_ops);
+
+void clk_agera_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+ const struct alpha_pll_config *config)
+{
+ if (config->l)
+ regmap_write(regmap, PLL_L_VAL(pll), config->l);
+
+ if (config->alpha)
+ regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
+
+ if (config->user_ctl_val)
+ regmap_write(regmap, PLL_USER_CTL(pll), config->user_ctl_val);
+
+ if (config->config_ctl_val)
+ regmap_write(regmap, PLL_CONFIG_CTL(pll),
+ config->config_ctl_val);
+
+ if (config->config_ctl_hi_val)
+ regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
+ config->config_ctl_hi_val);
+
+ if (config->test_ctl_val)
+ regmap_write(regmap, PLL_TEST_CTL(pll),
+ config->test_ctl_val);
+
+ if (config->test_ctl_hi_val)
+ regmap_write(regmap, PLL_TEST_CTL_U(pll),
+ config->test_ctl_hi_val);
+}
+EXPORT_SYMBOL_GPL(clk_agera_pll_configure);
+
+static int alpha_pll_agera_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ u32 l, alpha_width = pll_alpha_width(pll);
+ unsigned long rrate;
+ u64 a;
+
+ rrate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
+
+ /*
+ * Due to limited number of bits for fractional rate programming, the
+ * rounded up rate could be marginally higher than the requested rate.
+ */
+ if (rrate > (rate + PLL_RATE_MARGIN) || rrate < rate) {
+ pr_err("Call set rate on the PLL with rounded rates!\n");
+ return -EINVAL;
+ }
+
+ /* change L_VAL without having to go through the power on sequence */
+ regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
+ regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
+
+ /* Ensure that the write above goes through before proceeding. */
+ mb();
+
+ if (clk_hw_is_enabled(hw))
+ return wait_for_pll_enable_lock(pll);
+
+ return 0;
+}
+
+const struct clk_ops clk_alpha_pll_agera_ops = {
+ .enable = clk_alpha_pll_enable,
+ .disable = clk_alpha_pll_disable,
+ .is_enabled = clk_alpha_pll_is_enabled,
+ .recalc_rate = alpha_pll_fabia_recalc_rate,
+ .round_rate = clk_alpha_pll_round_rate,
+ .set_rate = alpha_pll_agera_set_rate,
+};
+EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index d3201b8..0ea30d2 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -15,6 +15,7 @@ enum {
CLK_ALPHA_PLL_TYPE_FABIA,
CLK_ALPHA_PLL_TYPE_TRION,
CLK_ALPHA_PLL_TYPE_LUCID = CLK_ALPHA_PLL_TYPE_TRION,
+ CLK_ALPHA_PLL_TYPE_AGERA,
CLK_ALPHA_PLL_TYPE_MAX,
};
@@ -141,6 +142,7 @@ extern const struct clk_ops clk_alpha_pll_postdiv_trion_ops;
extern const struct clk_ops clk_alpha_pll_lucid_ops;
#define clk_alpha_pll_fixed_lucid_ops clk_alpha_pll_fixed_trion_ops
extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
+extern const struct clk_ops clk_alpha_pll_agera_ops;
void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
@@ -148,6 +150,8 @@ void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
void clk_trion_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
+void clk_agera_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
+ const struct alpha_pll_config *config);
#define clk_lucid_pll_configure(pll, regmap, config) \
clk_trion_pll_configure(pll, regmap, config)
--
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member
of the Code Aurora Forum, hosted by the Linux Foundation.
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings.
[not found] <1599584848-15530-1-git-send-email-tdas@codeaurora.org>
2020-09-08 17:07 ` [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs Taniya Das
@ 2020-09-08 17:07 ` Taniya Das
2020-09-08 17:08 ` [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180 Taniya Das
` (3 subsequent siblings)
5 siblings, 0 replies; 9+ messages in thread
From: Taniya Das @ 2020-09-08 17:07 UTC (permalink / raw)
To: Stephen Boyd, Michael Turquette
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
The Camera Subsystem clock provider have a bunch of generic properties
that are needed in a device tree. Add a YAML schemas for those.
Add clock ids for Camera clocks which are required to bring the camera
subsystem out of reset.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
---
.../bindings/clock/qcom,sc7180-camcc.yaml | 73 +++++++++++++
include/dt-bindings/clock/qcom,camcc-sc7180.h | 121 +++++++++++++++++++++
2 files changed, 194 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
create mode 100644 include/dt-bindings/clock/qcom,camcc-sc7180.h
diff --git a/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
new file mode 100644
index 0000000..07bd38e
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
@@ -0,0 +1,73 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/qcom,sc7180-camcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Camera Clock & Reset Controller Binding for SC7180
+
+maintainers:
+ - Taniya Das <tdas@codeaurora.org>
+
+description: |
+ Qualcomm camera clock control module which supports the clocks, resets and
+ power domains on SC7180.
+
+ See also:
+ - dt-bindings/clock/qcom,camcc-sc7180.h.
+
+properties:
+ compatible:
+ const: qcom,sc7180-camcc
+
+ clocks:
+ items:
+ - description: Board XO source
+ - description: Camera_ahb clock from GCC
+ - description: Camera XO clock from GCC
+
+ clock-names:
+ items:
+ - const: bi_tcxo
+ - const: iface
+ - const: xo
+
+ '#clock-cells':
+ const: 1
+
+ '#reset-cells':
+ const: 1
+
+ '#power-domain-cells':
+ const: 1
+
+ reg:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - '#clock-cells'
+ - '#reset-cells'
+ - '#power-domain-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+ #include <dt-bindings/clock/qcom,rpmh.h>
+ clock-controller@ad00000 {
+ compatible = "qcom,sc7180-camcc";
+ reg = <0x0ad00000 0x10000>;
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_CAMERA_AHB_CLK>,
+ <&gcc GCC_CAMERA_XO_CLK>;
+ clock-names = "bi_tcxo", "iface", "xo";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+...
diff --git a/include/dt-bindings/clock/qcom,camcc-sc7180.h b/include/dt-bindings/clock/qcom,camcc-sc7180.h
new file mode 100644
index 0000000..ef7d3a0
--- /dev/null
+++ b/include/dt-bindings/clock/qcom,camcc-sc7180.h
@@ -0,0 +1,121 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef _DT_BINDINGS_CLK_QCOM_CAM_CC_SC7180_H
+#define _DT_BINDINGS_CLK_QCOM_CAM_CC_SC7180_H
+
+/* CAM_CC clocks */
+#define CAM_CC_PLL2_OUT_EARLY 0
+#define CAM_CC_PLL0 1
+#define CAM_CC_PLL1 2
+#define CAM_CC_PLL2 3
+#define CAM_CC_PLL2_OUT_AUX 4
+#define CAM_CC_PLL3 5
+#define CAM_CC_CAMNOC_AXI_CLK 6
+#define CAM_CC_CCI_0_CLK 7
+#define CAM_CC_CCI_0_CLK_SRC 8
+#define CAM_CC_CCI_1_CLK 9
+#define CAM_CC_CCI_1_CLK_SRC 10
+#define CAM_CC_CORE_AHB_CLK 11
+#define CAM_CC_CPAS_AHB_CLK 12
+#define CAM_CC_CPHY_RX_CLK_SRC 13
+#define CAM_CC_CSI0PHYTIMER_CLK 14
+#define CAM_CC_CSI0PHYTIMER_CLK_SRC 15
+#define CAM_CC_CSI1PHYTIMER_CLK 16
+#define CAM_CC_CSI1PHYTIMER_CLK_SRC 17
+#define CAM_CC_CSI2PHYTIMER_CLK 18
+#define CAM_CC_CSI2PHYTIMER_CLK_SRC 19
+#define CAM_CC_CSI3PHYTIMER_CLK 20
+#define CAM_CC_CSI3PHYTIMER_CLK_SRC 21
+#define CAM_CC_CSIPHY0_CLK 22
+#define CAM_CC_CSIPHY1_CLK 23
+#define CAM_CC_CSIPHY2_CLK 24
+#define CAM_CC_CSIPHY3_CLK 25
+#define CAM_CC_FAST_AHB_CLK_SRC 26
+#define CAM_CC_ICP_APB_CLK 27
+#define CAM_CC_ICP_ATB_CLK 28
+#define CAM_CC_ICP_CLK 29
+#define CAM_CC_ICP_CLK_SRC 30
+#define CAM_CC_ICP_CTI_CLK 31
+#define CAM_CC_ICP_TS_CLK 32
+#define CAM_CC_IFE_0_AXI_CLK 33
+#define CAM_CC_IFE_0_CLK 34
+#define CAM_CC_IFE_0_CLK_SRC 35
+#define CAM_CC_IFE_0_CPHY_RX_CLK 36
+#define CAM_CC_IFE_0_CSID_CLK 37
+#define CAM_CC_IFE_0_CSID_CLK_SRC 38
+#define CAM_CC_IFE_0_DSP_CLK 39
+#define CAM_CC_IFE_1_AXI_CLK 40
+#define CAM_CC_IFE_1_CLK 41
+#define CAM_CC_IFE_1_CLK_SRC 42
+#define CAM_CC_IFE_1_CPHY_RX_CLK 43
+#define CAM_CC_IFE_1_CSID_CLK 44
+#define CAM_CC_IFE_1_CSID_CLK_SRC 45
+#define CAM_CC_IFE_1_DSP_CLK 46
+#define CAM_CC_IFE_LITE_CLK 47
+#define CAM_CC_IFE_LITE_CLK_SRC 48
+#define CAM_CC_IFE_LITE_CPHY_RX_CLK 49
+#define CAM_CC_IFE_LITE_CSID_CLK 50
+#define CAM_CC_IFE_LITE_CSID_CLK_SRC 51
+#define CAM_CC_IPE_0_AHB_CLK 52
+#define CAM_CC_IPE_0_AREG_CLK 53
+#define CAM_CC_IPE_0_AXI_CLK 54
+#define CAM_CC_IPE_0_CLK 55
+#define CAM_CC_IPE_0_CLK_SRC 56
+#define CAM_CC_JPEG_CLK 57
+#define CAM_CC_JPEG_CLK_SRC 58
+#define CAM_CC_LRME_CLK 59
+#define CAM_CC_LRME_CLK_SRC 60
+#define CAM_CC_MCLK0_CLK 61
+#define CAM_CC_MCLK0_CLK_SRC 62
+#define CAM_CC_MCLK1_CLK 63
+#define CAM_CC_MCLK1_CLK_SRC 64
+#define CAM_CC_MCLK2_CLK 65
+#define CAM_CC_MCLK2_CLK_SRC 66
+#define CAM_CC_MCLK3_CLK 67
+#define CAM_CC_MCLK3_CLK_SRC 68
+#define CAM_CC_MCLK4_CLK 69
+#define CAM_CC_MCLK4_CLK_SRC 70
+#define CAM_CC_BPS_AHB_CLK 71
+#define CAM_CC_BPS_AREG_CLK 72
+#define CAM_CC_BPS_AXI_CLK 73
+#define CAM_CC_BPS_CLK 74
+#define CAM_CC_BPS_CLK_SRC 75
+#define CAM_CC_SLOW_AHB_CLK_SRC 76
+#define CAM_CC_SOC_AHB_CLK 77
+#define CAM_CC_SYS_TMR_CLK 78
+
+/* CAM_CC power domains */
+#define BPS_GDSC 0
+#define IFE_0_GDSC 1
+#define IFE_1_GDSC 2
+#define IPE_0_GDSC 3
+#define TITAN_TOP_GDSC 4
+
+/* CAM_CC resets */
+#define CAM_CC_BPS_BCR 0
+#define CAM_CC_CAMNOC_BCR 1
+#define CAM_CC_CCI_0_BCR 2
+#define CAM_CC_CCI_1_BCR 3
+#define CAM_CC_CPAS_BCR 4
+#define CAM_CC_CSI0PHY_BCR 5
+#define CAM_CC_CSI1PHY_BCR 6
+#define CAM_CC_CSI2PHY_BCR 7
+#define CAM_CC_CSI3PHY_BCR 8
+#define CAM_CC_ICP_BCR 9
+#define CAM_CC_IFE_0_BCR 10
+#define CAM_CC_IFE_1_BCR 11
+#define CAM_CC_IFE_LITE_BCR 12
+#define CAM_CC_IPE_0_BCR 13
+#define CAM_CC_JPEG_BCR 14
+#define CAM_CC_LRME_BCR 15
+#define CAM_CC_MCLK0_BCR 16
+#define CAM_CC_MCLK1_BCR 17
+#define CAM_CC_MCLK2_BCR 18
+#define CAM_CC_MCLK3_BCR 19
+#define CAM_CC_MCLK4_BCR 20
+#define CAM_CC_TITAN_TOP_BCR 21
+
+#endif
--
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member
of the Code Aurora Forum, hosted by the Linux Foundation.
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180
[not found] <1599584848-15530-1-git-send-email-tdas@codeaurora.org>
2020-09-08 17:07 ` [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs Taniya Das
2020-09-08 17:07 ` [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings Taniya Das
@ 2020-09-08 17:08 ` Taniya Das
2020-09-21 19:03 ` kernel test robot
2020-09-08 21:41 ` [PATCH v1 0/3] Add Camera " Stephen Boyd
` (2 subsequent siblings)
5 siblings, 1 reply; 9+ messages in thread
From: Taniya Das @ 2020-09-08 17:08 UTC (permalink / raw)
To: Stephen Boyd, Michael Turquette
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
Add support for the camera clock controller found on SC7180 based devices.
This would allow camera drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 9 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/camcc-sc7180.c | 1737 +++++++++++++++++++++++++++++++++++++++
3 files changed, 1747 insertions(+)
create mode 100644 drivers/clk/qcom/camcc-sc7180.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 0583273..7aeebe6 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -290,6 +290,15 @@ config QCS_GCC_404
Say Y if you want to use multimedia devices or peripheral
devices such as UART, SPI, I2C, USB, SD/eMMC, PCIe etc.
+config SC_CAMCC_7180
+ tristate "SC7180 Camera Clock Controller"
+ select SC_GCC_7180
+ help
+ Support for the camera clock controller on Qualcomm Technologies, Inc
+ SC7180 devices.
+ Say Y if you want to support camera devices and functionality such as
+ capturing pictures.
+
config SC_DISPCC_7180
tristate "SC7180 Display Clock Controller"
select SC_GCC_7180
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 9677e76..8e0579f 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -51,6 +51,7 @@ obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
obj-$(CONFIG_QCS_GCC_404) += gcc-qcs404.o
obj-$(CONFIG_QCS_Q6SSTOP_404) += q6sstop-qcs404.o
obj-$(CONFIG_QCS_TURING_404) += turingcc-qcs404.o
+obj-$(CONFIG_SC_CAMCC_7180) += camcc-sc7180.o
obj-$(CONFIG_SC_DISPCC_7180) += dispcc-sc7180.o
obj-$(CONFIG_SC_GCC_7180) += gcc-sc7180.o
obj-$(CONFIG_SC_GPUCC_7180) += gpucc-sc7180.o
diff --git a/drivers/clk/qcom/camcc-sc7180.c b/drivers/clk/qcom/camcc-sc7180.c
new file mode 100644
index 0000000..e954d21
--- /dev/null
+++ b/drivers/clk/qcom/camcc-sc7180.c
@@ -0,0 +1,1737 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pm_clock.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,camcc-sc7180.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-branch.h"
+#include "clk-rcg.h"
+#include "clk-regmap.h"
+#include "common.h"
+#include "gdsc.h"
+#include "reset.h"
+
+enum {
+ P_BI_TCXO,
+ P_CAM_CC_PLL0_OUT_EVEN,
+ P_CAM_CC_PLL1_OUT_EVEN,
+ P_CAM_CC_PLL2_OUT_AUX,
+ P_CAM_CC_PLL2_OUT_EARLY,
+ P_CAM_CC_PLL3_OUT_MAIN,
+ P_CORE_BI_PLL_TEST_SE,
+};
+
+static struct pll_vco agera_vco[] = {
+ { 600000000, 3300000000, 0 },
+};
+
+static struct pll_vco fabia_vco[] = {
+ { 249600000, 2000000000, 0 },
+};
+
+/* 600MHz configuration */
+static const struct alpha_pll_config cam_cc_pll0_config = {
+ .l = 0x1F,
+ .alpha = 0x4000,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00002067,
+ .test_ctl_val = 0x40000000,
+ .user_ctl_hi_val = 0x00004805,
+ .user_ctl_val = 0x00000001,
+};
+
+static struct clk_alpha_pll cam_cc_pll0 = {
+ .offset = 0x0,
+ .vco_table = fabia_vco,
+ .num_vco = ARRAY_SIZE(fabia_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_FABIA],
+ .clkr = {
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll0",
+ .parent_data = &(const struct clk_parent_data){
+ .fw_name = "bi_tcxo",
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_fabia_ops,
+ },
+ },
+};
+
+/* 860MHz configuration */
+static const struct alpha_pll_config cam_cc_pll1_config = {
+ .l = 0x2A,
+ .alpha = 0x1555,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00002067,
+ .test_ctl_val = 0x40000000,
+ .user_ctl_hi_val = 0x00004805,
+};
+
+static struct clk_alpha_pll cam_cc_pll1 = {
+ .offset = 0x1000,
+ .vco_table = fabia_vco,
+ .num_vco = ARRAY_SIZE(fabia_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_FABIA],
+ .clkr = {
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll1",
+ .parent_data = &(const struct clk_parent_data){
+ .fw_name = "bi_tcxo",
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_fabia_ops,
+ },
+ },
+};
+
+/* 1920MHz configuration */
+static const struct alpha_pll_config cam_cc_pll2_config = {
+ .l = 0x64,
+ .config_ctl_val = 0x20000800,
+ .config_ctl_hi_val = 0x400003D2,
+ .test_ctl_val = 0x04000400,
+ .test_ctl_hi_val = 0x00004000,
+ .user_ctl_val = 0x0000030F,
+};
+
+static struct clk_alpha_pll cam_cc_pll2 = {
+ .offset = 0x2000,
+ .vco_table = agera_vco,
+ .num_vco = ARRAY_SIZE(agera_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_AGERA],
+ .clkr = {
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll2",
+ .parent_data = &(const struct clk_parent_data){
+ .fw_name = "bi_tcxo",
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_agera_ops,
+ },
+ },
+};
+
+static struct clk_fixed_factor cam_cc_pll2_out_early = {
+ .mult = 1,
+ .div = 2,
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll2_out_early",
+ .parent_names = (const char *[]){ "cam_cc_pll2" },
+ .num_parents = 1,
+ .ops = &clk_fixed_factor_ops,
+ },
+};
+
+static const struct clk_div_table post_div_table_cam_cc_pll2_out_aux[] = {
+ { 0x3, 4 },
+ { }
+};
+
+static struct clk_alpha_pll_postdiv cam_cc_pll2_out_aux = {
+ .offset = 0x2000,
+ .post_div_shift = 8,
+ .post_div_table = post_div_table_cam_cc_pll2_out_aux,
+ .num_post_div = ARRAY_SIZE(post_div_table_cam_cc_pll2_out_aux),
+ .width = 2,
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_AGERA],
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll2_out_aux",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_pll2.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_alpha_pll_postdiv_ops,
+ },
+};
+
+/* 1080MHz configuration */
+static const struct alpha_pll_config cam_cc_pll3_config = {
+ .l = 0x38,
+ .alpha = 0x4000,
+ .config_ctl_val = 0x20485699,
+ .config_ctl_hi_val = 0x00002067,
+ .test_ctl_val = 0x40000000,
+ .user_ctl_hi_val = 0x00004805,
+};
+
+static struct clk_alpha_pll cam_cc_pll3 = {
+ .offset = 0x3000,
+ .vco_table = fabia_vco,
+ .num_vco = ARRAY_SIZE(fabia_vco),
+ .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_FABIA],
+ .clkr = {
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_pll3",
+ .parent_data = &(const struct clk_parent_data){
+ .fw_name = "bi_tcxo",
+ },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_fabia_ops,
+ },
+ },
+};
+
+static const struct parent_map cam_cc_parent_map_0[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL1_OUT_EVEN, 2 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_0[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll1.clkr.hw },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_1[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL2_OUT_AUX, 1 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_1[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll2_out_aux.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_2[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL2_OUT_EARLY, 4 },
+ { P_CAM_CC_PLL3_OUT_MAIN, 5 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_2[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll2_out_early.hw },
+ { .hw = &cam_cc_pll3.clkr.hw },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_3[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL1_OUT_EVEN, 2 },
+ { P_CAM_CC_PLL2_OUT_EARLY, 4 },
+ { P_CAM_CC_PLL3_OUT_MAIN, 5 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_3[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll1.clkr.hw },
+ { .hw = &cam_cc_pll2_out_early.hw },
+ { .hw = &cam_cc_pll3.clkr.hw },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_4[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL3_OUT_MAIN, 5 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_4[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll3.clkr.hw },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_5[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_5[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct parent_map cam_cc_parent_map_6[] = {
+ { P_BI_TCXO, 0 },
+ { P_CAM_CC_PLL1_OUT_EVEN, 2 },
+ { P_CAM_CC_PLL3_OUT_MAIN, 5 },
+ { P_CAM_CC_PLL0_OUT_EVEN, 6 },
+ { P_CORE_BI_PLL_TEST_SE, 7 },
+};
+
+static const struct clk_parent_data cam_cc_parent_data_6[] = {
+ { .fw_name = "bi_tcxo" },
+ { .hw = &cam_cc_pll1.clkr.hw },
+ { .hw = &cam_cc_pll3.clkr.hw },
+ { .hw = &cam_cc_pll0.clkr.hw },
+ { .fw_name = "core_bi_pll_test_se", .name = "core_bi_pll_test_se" },
+};
+
+static const struct freq_tbl ftbl_cam_cc_bps_clk_src[] = {
+ F(200000000, P_CAM_CC_PLL0_OUT_EVEN, 3, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ F(432000000, P_CAM_CC_PLL3_OUT_MAIN, 2.5, 0, 0),
+ F(480000000, P_CAM_CC_PLL2_OUT_EARLY, 2, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_bps_clk_src = {
+ .cmd_rcgr = 0x6010,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_2,
+ .freq_tbl = ftbl_cam_cc_bps_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_bps_clk_src",
+ .parent_data = cam_cc_parent_data_2,
+ .num_parents = 5,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_cci_0_clk_src[] = {
+ F(37500000, P_CAM_CC_PLL0_OUT_EVEN, 16, 0, 0),
+ F(50000000, P_CAM_CC_PLL0_OUT_EVEN, 12, 0, 0),
+ F(100000000, P_CAM_CC_PLL0_OUT_EVEN, 6, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_cci_0_clk_src = {
+ .cmd_rcgr = 0xb0d8,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_5,
+ .freq_tbl = ftbl_cam_cc_cci_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cci_0_clk_src",
+ .parent_data = cam_cc_parent_data_5,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_cci_1_clk_src = {
+ .cmd_rcgr = 0xb14c,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_5,
+ .freq_tbl = ftbl_cam_cc_cci_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cci_1_clk_src",
+ .parent_data = cam_cc_parent_data_5,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_cphy_rx_clk_src[] = {
+ F(150000000, P_CAM_CC_PLL0_OUT_EVEN, 4, 0, 0),
+ F(270000000, P_CAM_CC_PLL3_OUT_MAIN, 4, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_cphy_rx_clk_src = {
+ .cmd_rcgr = 0x9064,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_3,
+ .freq_tbl = ftbl_cam_cc_cphy_rx_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cphy_rx_clk_src",
+ .parent_data = cam_cc_parent_data_3,
+ .num_parents = 6,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_csi0phytimer_clk_src[] = {
+ F(300000000, P_CAM_CC_PLL0_OUT_EVEN, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_csi0phytimer_clk_src = {
+ .cmd_rcgr = 0x5004,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi0phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi1phytimer_clk_src = {
+ .cmd_rcgr = 0x5028,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi1phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi2phytimer_clk_src = {
+ .cmd_rcgr = 0x504c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi2phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_csi3phytimer_clk_src = {
+ .cmd_rcgr = 0x5070,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_csi0phytimer_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi3phytimer_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_fast_ahb_clk_src[] = {
+ F(100000000, P_CAM_CC_PLL0_OUT_EVEN, 6, 0, 0),
+ F(200000000, P_CAM_CC_PLL0_OUT_EVEN, 3, 0, 0),
+ F(300000000, P_CAM_CC_PLL0_OUT_EVEN, 2, 0, 0),
+ F(404000000, P_CAM_CC_PLL1_OUT_EVEN, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_fast_ahb_clk_src = {
+ .cmd_rcgr = 0x603c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_fast_ahb_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_fast_ahb_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_icp_clk_src[] = {
+ F(240000000, P_CAM_CC_PLL0_OUT_EVEN, 2.5, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ F(432000000, P_CAM_CC_PLL3_OUT_MAIN, 2.5, 0, 0),
+ F(480000000, P_CAM_CC_PLL2_OUT_EARLY, 2, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_icp_clk_src = {
+ .cmd_rcgr = 0xb088,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_2,
+ .freq_tbl = ftbl_cam_cc_icp_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_icp_clk_src",
+ .parent_data = cam_cc_parent_data_2,
+ .num_parents = 5,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_ife_0_clk_src[] = {
+ F(240000000, P_CAM_CC_PLL0_OUT_EVEN, 2.5, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ F(432000000, P_CAM_CC_PLL3_OUT_MAIN, 2.5, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_ife_0_clk_src = {
+ .cmd_rcgr = 0x9010,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_4,
+ .freq_tbl = ftbl_cam_cc_ife_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_clk_src",
+ .parent_data = cam_cc_parent_data_4,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_ife_0_csid_clk_src[] = {
+ F(150000000, P_CAM_CC_PLL0_OUT_EVEN, 4, 0, 0),
+ F(270000000, P_CAM_CC_PLL3_OUT_MAIN, 4, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ F(480000000, P_CAM_CC_PLL2_OUT_EARLY, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_ife_0_csid_clk_src = {
+ .cmd_rcgr = 0x903c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_3,
+ .freq_tbl = ftbl_cam_cc_ife_0_csid_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_csid_clk_src",
+ .parent_data = cam_cc_parent_data_3,
+ .num_parents = 6,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_1_clk_src = {
+ .cmd_rcgr = 0xa010,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_4,
+ .freq_tbl = ftbl_cam_cc_ife_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_clk_src",
+ .parent_data = cam_cc_parent_data_4,
+ .num_parents = 4,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_1_csid_clk_src = {
+ .cmd_rcgr = 0xa034,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_3,
+ .freq_tbl = ftbl_cam_cc_ife_0_csid_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_csid_clk_src",
+ .parent_data = cam_cc_parent_data_3,
+ .num_parents = 6,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_lite_clk_src = {
+ .cmd_rcgr = 0xb004,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_4,
+ .freq_tbl = ftbl_cam_cc_ife_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_lite_clk_src",
+ .parent_data = cam_cc_parent_data_4,
+ .num_parents = 4,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_ife_lite_csid_clk_src = {
+ .cmd_rcgr = 0xb024,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_3,
+ .freq_tbl = ftbl_cam_cc_ife_0_csid_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_lite_csid_clk_src",
+ .parent_data = cam_cc_parent_data_3,
+ .num_parents = 6,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_ipe_0_clk_src[] = {
+ F(240000000, P_CAM_CC_PLL0_OUT_EVEN, 2.5, 0, 0),
+ F(360000000, P_CAM_CC_PLL3_OUT_MAIN, 3, 0, 0),
+ F(432000000, P_CAM_CC_PLL3_OUT_MAIN, 2.5, 0, 0),
+ F(540000000, P_CAM_CC_PLL3_OUT_MAIN, 2, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_ipe_0_clk_src = {
+ .cmd_rcgr = 0x7010,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_2,
+ .freq_tbl = ftbl_cam_cc_ipe_0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ipe_0_clk_src",
+ .parent_data = cam_cc_parent_data_2,
+ .num_parents = 5,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_jpeg_clk_src[] = {
+ F(66666667, P_CAM_CC_PLL0_OUT_EVEN, 9, 0, 0),
+ F(133333333, P_CAM_CC_PLL0_OUT_EVEN, 4.5, 0, 0),
+ F(216000000, P_CAM_CC_PLL3_OUT_MAIN, 5, 0, 0),
+ F(320000000, P_CAM_CC_PLL2_OUT_EARLY, 3, 0, 0),
+ F(600000000, P_CAM_CC_PLL0_OUT_EVEN, 1, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_jpeg_clk_src = {
+ .cmd_rcgr = 0xb04c,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_2,
+ .freq_tbl = ftbl_cam_cc_jpeg_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_jpeg_clk_src",
+ .parent_data = cam_cc_parent_data_2,
+ .num_parents = 5,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_lrme_clk_src[] = {
+ F(200000000, P_CAM_CC_PLL0_OUT_EVEN, 3, 0, 0),
+ F(216000000, P_CAM_CC_PLL3_OUT_MAIN, 5, 0, 0),
+ F(300000000, P_CAM_CC_PLL0_OUT_EVEN, 2, 0, 0),
+ F(404000000, P_CAM_CC_PLL1_OUT_EVEN, 2, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_lrme_clk_src = {
+ .cmd_rcgr = 0xb0f8,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_6,
+ .freq_tbl = ftbl_cam_cc_lrme_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_lrme_clk_src",
+ .parent_data = cam_cc_parent_data_6,
+ .num_parents = 5,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_mclk0_clk_src[] = {
+ F(19200000, P_BI_TCXO, 1, 0, 0),
+ F(24000000, P_CAM_CC_PLL2_OUT_AUX, 10, 1, 2),
+ F(64000000, P_CAM_CC_PLL2_OUT_AUX, 7.5, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_mclk0_clk_src = {
+ .cmd_rcgr = 0x4004,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_mclk0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk0_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_mclk1_clk_src = {
+ .cmd_rcgr = 0x4024,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_mclk0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk1_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_mclk2_clk_src = {
+ .cmd_rcgr = 0x4044,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_mclk0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk2_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_mclk3_clk_src = {
+ .cmd_rcgr = 0x4064,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_mclk0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk3_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_rcg2 cam_cc_mclk4_clk_src = {
+ .cmd_rcgr = 0x4084,
+ .mnd_width = 8,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_1,
+ .freq_tbl = ftbl_cam_cc_mclk0_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk4_clk_src",
+ .parent_data = cam_cc_parent_data_1,
+ .num_parents = 3,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static const struct freq_tbl ftbl_cam_cc_slow_ahb_clk_src[] = {
+ F(80000000, P_CAM_CC_PLL0_OUT_EVEN, 7.5, 0, 0),
+ { }
+};
+
+static struct clk_rcg2 cam_cc_slow_ahb_clk_src = {
+ .cmd_rcgr = 0x6058,
+ .mnd_width = 0,
+ .hid_width = 5,
+ .parent_map = cam_cc_parent_map_0,
+ .freq_tbl = ftbl_cam_cc_slow_ahb_clk_src,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "cam_cc_slow_ahb_clk_src",
+ .parent_data = cam_cc_parent_data_0,
+ .num_parents = 4,
+ .flags = CLK_SET_RATE_PARENT | CLK_OPS_PARENT_ENABLE,
+ .ops = &clk_rcg2_ops,
+ },
+};
+
+static struct clk_branch cam_cc_bps_ahb_clk = {
+ .halt_reg = 0x6070,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x6070,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_bps_ahb_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_bps_areg_clk = {
+ .halt_reg = 0x6054,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x6054,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_bps_areg_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_bps_axi_clk = {
+ .halt_reg = 0x6038,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x6038,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_bps_axi_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_bps_clk = {
+ .halt_reg = 0x6028,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x6028,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_bps_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_bps_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_camnoc_axi_clk = {
+ .halt_reg = 0xb124,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb124,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_camnoc_axi_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cci_0_clk = {
+ .halt_reg = 0xb0f0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb0f0,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cci_0_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cci_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cci_1_clk = {
+ .halt_reg = 0xb164,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb164,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cci_1_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cci_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_core_ahb_clk = {
+ .halt_reg = 0xb144,
+ .halt_check = BRANCH_HALT_DELAY,
+ .clkr = {
+ .enable_reg = 0xb144,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_core_ahb_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_cpas_ahb_clk = {
+ .halt_reg = 0xb11c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb11c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_cpas_ahb_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi0phytimer_clk = {
+ .halt_reg = 0x501c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x501c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi0phytimer_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_csi0phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi1phytimer_clk = {
+ .halt_reg = 0x5040,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5040,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi1phytimer_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_csi1phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi2phytimer_clk = {
+ .halt_reg = 0x5064,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5064,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi2phytimer_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_csi2phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csi3phytimer_clk = {
+ .halt_reg = 0x5088,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5088,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csi3phytimer_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_csi3phytimer_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy0_clk = {
+ .halt_reg = 0x5020,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5020,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csiphy0_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy1_clk = {
+ .halt_reg = 0x5044,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5044,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csiphy1_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy2_clk = {
+ .halt_reg = 0x5068,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x5068,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csiphy2_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_csiphy3_clk = {
+ .halt_reg = 0x508c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x508c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_csiphy3_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_icp_clk = {
+ .halt_reg = 0xb0a0,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb0a0,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_icp_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_icp_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_0_axi_clk = {
+ .halt_reg = 0x9080,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9080,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_axi_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_0_clk = {
+ .halt_reg = 0x9028,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9028,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_0_cphy_rx_clk = {
+ .halt_reg = 0x907c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x907c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_cphy_rx_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_0_csid_clk = {
+ .halt_reg = 0x9054,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9054,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_csid_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_0_csid_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_0_dsp_clk = {
+ .halt_reg = 0x9038,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x9038,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_0_dsp_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_1_axi_clk = {
+ .halt_reg = 0xa058,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xa058,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_axi_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_1_clk = {
+ .halt_reg = 0xa028,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xa028,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_1_cphy_rx_clk = {
+ .halt_reg = 0xa054,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xa054,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_cphy_rx_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_1_csid_clk = {
+ .halt_reg = 0xa04c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xa04c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_csid_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_1_csid_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_1_dsp_clk = {
+ .halt_reg = 0xa030,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xa030,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_1_dsp_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_clk = {
+ .halt_reg = 0xb01c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb01c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_lite_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_lite_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_cphy_rx_clk = {
+ .halt_reg = 0xb044,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb044,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_lite_cphy_rx_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_cphy_rx_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ife_lite_csid_clk = {
+ .halt_reg = 0xb03c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb03c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ife_lite_csid_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ife_lite_csid_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_0_ahb_clk = {
+ .halt_reg = 0x7040,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x7040,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ipe_0_ahb_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_slow_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_0_areg_clk = {
+ .halt_reg = 0x703c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x703c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ipe_0_areg_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_fast_ahb_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_0_axi_clk = {
+ .halt_reg = 0x7038,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x7038,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ipe_0_axi_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_ipe_0_clk = {
+ .halt_reg = 0x7028,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x7028,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_ipe_0_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_ipe_0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_jpeg_clk = {
+ .halt_reg = 0xb064,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb064,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_jpeg_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_jpeg_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_lrme_clk = {
+ .halt_reg = 0xb110,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb110,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_lrme_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_lrme_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_mclk0_clk = {
+ .halt_reg = 0x401c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x401c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk0_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_mclk0_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_mclk1_clk = {
+ .halt_reg = 0x403c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x403c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk1_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_mclk1_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_mclk2_clk = {
+ .halt_reg = 0x405c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x405c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk2_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_mclk2_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_mclk3_clk = {
+ .halt_reg = 0x407c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x407c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk3_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_mclk3_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_mclk4_clk = {
+ .halt_reg = 0x409c,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0x409c,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_mclk4_clk",
+ .parent_data = &(const struct clk_parent_data){
+ .hw = &cam_cc_mclk4_clk_src.clkr.hw,
+ },
+ .num_parents = 1,
+ .flags = CLK_SET_RATE_PARENT,
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_soc_ahb_clk = {
+ .halt_reg = 0xb140,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb140,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_soc_ahb_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct clk_branch cam_cc_sys_tmr_clk = {
+ .halt_reg = 0xb0a8,
+ .halt_check = BRANCH_HALT,
+ .clkr = {
+ .enable_reg = 0xb0a8,
+ .enable_mask = BIT(0),
+ .hw.init = &(struct clk_init_data){
+ .name = "cam_cc_sys_tmr_clk",
+ .ops = &clk_branch2_ops,
+ },
+ },
+};
+
+static struct gdsc bps_gdsc = {
+ .gdscr = 0x6004,
+ .pd = {
+ .name = "bps_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = HW_CTRL,
+};
+
+static struct gdsc ife_0_gdsc = {
+ .gdscr = 0x9004,
+ .pd = {
+ .name = "ife_0_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+};
+
+static struct gdsc ife_1_gdsc = {
+ .gdscr = 0xa004,
+ .pd = {
+ .name = "ife_1_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+};
+
+static struct gdsc ipe_0_gdsc = {
+ .gdscr = 0x7004,
+ .pd = {
+ .name = "ipe_0_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+ .flags = HW_CTRL,
+};
+
+static struct gdsc titan_top_gdsc = {
+ .gdscr = 0xb134,
+ .pd = {
+ .name = "titan_top_gdsc",
+ },
+ .pwrsts = PWRSTS_OFF_ON,
+};
+
+struct clk_hw *cam_cc_sc7180_hws[] = {
+ [CAM_CC_PLL2_OUT_EARLY] = &cam_cc_pll2_out_early.hw,
+};
+
+static struct clk_regmap *cam_cc_sc7180_clocks[] = {
+ [CAM_CC_BPS_AHB_CLK] = &cam_cc_bps_ahb_clk.clkr,
+ [CAM_CC_BPS_AREG_CLK] = &cam_cc_bps_areg_clk.clkr,
+ [CAM_CC_BPS_AXI_CLK] = &cam_cc_bps_axi_clk.clkr,
+ [CAM_CC_BPS_CLK] = &cam_cc_bps_clk.clkr,
+ [CAM_CC_BPS_CLK_SRC] = &cam_cc_bps_clk_src.clkr,
+ [CAM_CC_CAMNOC_AXI_CLK] = &cam_cc_camnoc_axi_clk.clkr,
+ [CAM_CC_CCI_0_CLK] = &cam_cc_cci_0_clk.clkr,
+ [CAM_CC_CCI_0_CLK_SRC] = &cam_cc_cci_0_clk_src.clkr,
+ [CAM_CC_CCI_1_CLK] = &cam_cc_cci_1_clk.clkr,
+ [CAM_CC_CCI_1_CLK_SRC] = &cam_cc_cci_1_clk_src.clkr,
+ [CAM_CC_CORE_AHB_CLK] = &cam_cc_core_ahb_clk.clkr,
+ [CAM_CC_CPAS_AHB_CLK] = &cam_cc_cpas_ahb_clk.clkr,
+ [CAM_CC_CPHY_RX_CLK_SRC] = &cam_cc_cphy_rx_clk_src.clkr,
+ [CAM_CC_CSI0PHYTIMER_CLK] = &cam_cc_csi0phytimer_clk.clkr,
+ [CAM_CC_CSI0PHYTIMER_CLK_SRC] = &cam_cc_csi0phytimer_clk_src.clkr,
+ [CAM_CC_CSI1PHYTIMER_CLK] = &cam_cc_csi1phytimer_clk.clkr,
+ [CAM_CC_CSI1PHYTIMER_CLK_SRC] = &cam_cc_csi1phytimer_clk_src.clkr,
+ [CAM_CC_CSI2PHYTIMER_CLK] = &cam_cc_csi2phytimer_clk.clkr,
+ [CAM_CC_CSI2PHYTIMER_CLK_SRC] = &cam_cc_csi2phytimer_clk_src.clkr,
+ [CAM_CC_CSI3PHYTIMER_CLK] = &cam_cc_csi3phytimer_clk.clkr,
+ [CAM_CC_CSI3PHYTIMER_CLK_SRC] = &cam_cc_csi3phytimer_clk_src.clkr,
+ [CAM_CC_CSIPHY0_CLK] = &cam_cc_csiphy0_clk.clkr,
+ [CAM_CC_CSIPHY1_CLK] = &cam_cc_csiphy1_clk.clkr,
+ [CAM_CC_CSIPHY2_CLK] = &cam_cc_csiphy2_clk.clkr,
+ [CAM_CC_CSIPHY3_CLK] = &cam_cc_csiphy3_clk.clkr,
+ [CAM_CC_FAST_AHB_CLK_SRC] = &cam_cc_fast_ahb_clk_src.clkr,
+ [CAM_CC_ICP_CLK] = &cam_cc_icp_clk.clkr,
+ [CAM_CC_ICP_CLK_SRC] = &cam_cc_icp_clk_src.clkr,
+ [CAM_CC_IFE_0_AXI_CLK] = &cam_cc_ife_0_axi_clk.clkr,
+ [CAM_CC_IFE_0_CLK] = &cam_cc_ife_0_clk.clkr,
+ [CAM_CC_IFE_0_CLK_SRC] = &cam_cc_ife_0_clk_src.clkr,
+ [CAM_CC_IFE_0_CPHY_RX_CLK] = &cam_cc_ife_0_cphy_rx_clk.clkr,
+ [CAM_CC_IFE_0_CSID_CLK] = &cam_cc_ife_0_csid_clk.clkr,
+ [CAM_CC_IFE_0_CSID_CLK_SRC] = &cam_cc_ife_0_csid_clk_src.clkr,
+ [CAM_CC_IFE_0_DSP_CLK] = &cam_cc_ife_0_dsp_clk.clkr,
+ [CAM_CC_IFE_1_AXI_CLK] = &cam_cc_ife_1_axi_clk.clkr,
+ [CAM_CC_IFE_1_CLK] = &cam_cc_ife_1_clk.clkr,
+ [CAM_CC_IFE_1_CLK_SRC] = &cam_cc_ife_1_clk_src.clkr,
+ [CAM_CC_IFE_1_CPHY_RX_CLK] = &cam_cc_ife_1_cphy_rx_clk.clkr,
+ [CAM_CC_IFE_1_CSID_CLK] = &cam_cc_ife_1_csid_clk.clkr,
+ [CAM_CC_IFE_1_CSID_CLK_SRC] = &cam_cc_ife_1_csid_clk_src.clkr,
+ [CAM_CC_IFE_1_DSP_CLK] = &cam_cc_ife_1_dsp_clk.clkr,
+ [CAM_CC_IFE_LITE_CLK] = &cam_cc_ife_lite_clk.clkr,
+ [CAM_CC_IFE_LITE_CLK_SRC] = &cam_cc_ife_lite_clk_src.clkr,
+ [CAM_CC_IFE_LITE_CPHY_RX_CLK] = &cam_cc_ife_lite_cphy_rx_clk.clkr,
+ [CAM_CC_IFE_LITE_CSID_CLK] = &cam_cc_ife_lite_csid_clk.clkr,
+ [CAM_CC_IFE_LITE_CSID_CLK_SRC] = &cam_cc_ife_lite_csid_clk_src.clkr,
+ [CAM_CC_IPE_0_AHB_CLK] = &cam_cc_ipe_0_ahb_clk.clkr,
+ [CAM_CC_IPE_0_AREG_CLK] = &cam_cc_ipe_0_areg_clk.clkr,
+ [CAM_CC_IPE_0_AXI_CLK] = &cam_cc_ipe_0_axi_clk.clkr,
+ [CAM_CC_IPE_0_CLK] = &cam_cc_ipe_0_clk.clkr,
+ [CAM_CC_IPE_0_CLK_SRC] = &cam_cc_ipe_0_clk_src.clkr,
+ [CAM_CC_JPEG_CLK] = &cam_cc_jpeg_clk.clkr,
+ [CAM_CC_JPEG_CLK_SRC] = &cam_cc_jpeg_clk_src.clkr,
+ [CAM_CC_LRME_CLK] = &cam_cc_lrme_clk.clkr,
+ [CAM_CC_LRME_CLK_SRC] = &cam_cc_lrme_clk_src.clkr,
+ [CAM_CC_MCLK0_CLK] = &cam_cc_mclk0_clk.clkr,
+ [CAM_CC_MCLK0_CLK_SRC] = &cam_cc_mclk0_clk_src.clkr,
+ [CAM_CC_MCLK1_CLK] = &cam_cc_mclk1_clk.clkr,
+ [CAM_CC_MCLK1_CLK_SRC] = &cam_cc_mclk1_clk_src.clkr,
+ [CAM_CC_MCLK2_CLK] = &cam_cc_mclk2_clk.clkr,
+ [CAM_CC_MCLK2_CLK_SRC] = &cam_cc_mclk2_clk_src.clkr,
+ [CAM_CC_MCLK3_CLK] = &cam_cc_mclk3_clk.clkr,
+ [CAM_CC_MCLK3_CLK_SRC] = &cam_cc_mclk3_clk_src.clkr,
+ [CAM_CC_MCLK4_CLK] = &cam_cc_mclk4_clk.clkr,
+ [CAM_CC_MCLK4_CLK_SRC] = &cam_cc_mclk4_clk_src.clkr,
+ [CAM_CC_PLL0] = &cam_cc_pll0.clkr,
+ [CAM_CC_PLL1] = &cam_cc_pll1.clkr,
+ [CAM_CC_PLL2] = &cam_cc_pll2.clkr,
+ [CAM_CC_PLL2_OUT_AUX] = &cam_cc_pll2_out_aux.clkr,
+ [CAM_CC_PLL3] = &cam_cc_pll3.clkr,
+ [CAM_CC_SLOW_AHB_CLK_SRC] = &cam_cc_slow_ahb_clk_src.clkr,
+ [CAM_CC_SOC_AHB_CLK] = &cam_cc_soc_ahb_clk.clkr,
+ [CAM_CC_SYS_TMR_CLK] = &cam_cc_sys_tmr_clk.clkr,
+};
+static struct gdsc *cam_cc_sc7180_gdscs[] = {
+ [BPS_GDSC] = &bps_gdsc,
+ [IFE_0_GDSC] = &ife_0_gdsc,
+ [IFE_1_GDSC] = &ife_1_gdsc,
+ [IPE_0_GDSC] = &ipe_0_gdsc,
+ [TITAN_TOP_GDSC] = &titan_top_gdsc,
+};
+
+static const struct regmap_config cam_cc_sc7180_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0xd028,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_desc cam_cc_sc7180_desc = {
+ .config = &cam_cc_sc7180_regmap_config,
+ .clk_hws = cam_cc_sc7180_hws,
+ .num_clk_hws = ARRAY_SIZE(cam_cc_sc7180_hws),
+ .clks = cam_cc_sc7180_clocks,
+ .num_clks = ARRAY_SIZE(cam_cc_sc7180_clocks),
+ .gdscs = cam_cc_sc7180_gdscs,
+ .num_gdscs = ARRAY_SIZE(cam_cc_sc7180_gdscs),
+};
+
+static const struct of_device_id cam_cc_sc7180_match_table[] = {
+ { .compatible = "qcom,sc7180-camcc" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, cam_cc_sc7180_match_table);
+
+static int cam_cc_sc7180_probe(struct platform_device *pdev)
+{
+ struct regmap *regmap;
+ int ret;
+
+ pm_runtime_enable(&pdev->dev);
+ ret = pm_clk_create(&pdev->dev);
+ if (ret)
+ return ret;
+
+ ret = pm_clk_add(&pdev->dev, "xo");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to acquire XO clock\n");
+ goto disable_pm_runtime;
+ }
+
+ ret = pm_clk_add(&pdev->dev, "iface");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "Failed to acquire iface clock\n");
+ goto disable_pm_runtime;
+ }
+
+ ret = pm_clk_runtime_resume(&pdev->dev);
+ if (ret) {
+ dev_err(&pdev->dev, "pm runtime resume failed\n");
+ goto destroy_pm_clk;
+ }
+
+ regmap = qcom_cc_map(pdev, &cam_cc_sc7180_desc);
+ if (IS_ERR(regmap)) {
+ ret = PTR_ERR(regmap);
+ goto destroy_pm_clk;
+ }
+
+ clk_fabia_pll_configure(&cam_cc_pll0, regmap, &cam_cc_pll0_config);
+ clk_fabia_pll_configure(&cam_cc_pll1, regmap, &cam_cc_pll1_config);
+ clk_agera_pll_configure(&cam_cc_pll2, regmap, &cam_cc_pll2_config);
+ clk_fabia_pll_configure(&cam_cc_pll3, regmap, &cam_cc_pll3_config);
+
+ ret = qcom_cc_really_probe(pdev, &cam_cc_sc7180_desc, regmap);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register CAM CC clocks\n");
+ goto suspend_pm_runtime;
+ }
+
+suspend_pm_runtime:
+ ret = pm_clk_runtime_suspend(&pdev->dev);
+ if (ret)
+ dev_err(&pdev->dev, "pm runtime suspend failed\n");
+
+ return 0;
+
+destroy_pm_clk:
+ pm_clk_destroy(&pdev->dev);
+
+disable_pm_runtime:
+ pm_runtime_disable(&pdev->dev);
+
+ return ret;
+}
+
+static const struct dev_pm_ops cam_cc_pm_ops = {
+ SET_RUNTIME_PM_OPS(pm_clk_suspend, pm_clk_resume, NULL)
+};
+
+static struct platform_driver cam_cc_sc7180_driver = {
+ .probe = cam_cc_sc7180_probe,
+ .driver = {
+ .name = "cam_cc-sc7180",
+ .of_match_table = cam_cc_sc7180_match_table,
+ .pm = &cam_cc_pm_ops,
+ },
+};
+
+static int __init cam_cc_sc7180_init(void)
+{
+ return platform_driver_register(&cam_cc_sc7180_driver);
+}
+subsys_initcall(cam_cc_sc7180_init);
+
+static void __exit cam_cc_sc7180_exit(void)
+{
+ platform_driver_unregister(&cam_cc_sc7180_driver);
+}
+module_exit(cam_cc_sc7180_exit);
+
+MODULE_DESCRIPTION("QTI CAM_CC SC7180 Driver");
+MODULE_LICENSE("GPL v2");
--
Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member
of the Code Aurora Forum, hosted by the Linux Foundation.
^ permalink raw reply related [flat|nested] 9+ messages in thread
* Re: [PATCH v1 0/3] Add Camera clock controller driver for SC7180
[not found] <1599584848-15530-1-git-send-email-tdas@codeaurora.org>
` (2 preceding siblings ...)
2020-09-08 17:08 ` [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180 Taniya Das
@ 2020-09-08 21:41 ` Stephen Boyd
[not found] ` <1599584848-15530-2-git-send-email-tdas@codeaurora.org>
[not found] ` <1599584848-15530-3-git-send-email-tdas@codeaurora.org>
5 siblings, 0 replies; 9+ messages in thread
From: Stephen Boyd @ 2020-09-08 21:41 UTC (permalink / raw)
To: Michael Turquette, Taniya Das
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
Quoting Taniya Das (2020-09-08 10:07:25)
> [v1]
> * Add support for Agera PLL which is used in the camera clock controller.
>
> * Add driver support for camera clock controller for SC7180 and also
> update device tree bindings for the various clocks supported in the
> clock controller.
I got duplicate patches in my inbox. Is something broken on the
codeaurora server?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs
[not found] ` <1599584848-15530-2-git-send-email-tdas@codeaurora.org>
@ 2020-09-15 0:13 ` Stephen Boyd
2020-10-13 17:03 ` Taniya Das
0 siblings, 1 reply; 9+ messages in thread
From: Stephen Boyd @ 2020-09-15 0:13 UTC (permalink / raw)
To: Michael Turquette, Taniya Das
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
Quoting Taniya Das (2020-09-08 10:07:26)
> diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
> index 26139ef..fb27fcf 100644
> --- a/drivers/clk/qcom/clk-alpha-pll.c
> +++ b/drivers/clk/qcom/clk-alpha-pll.c
> @@ -1561,3 +1571,75 @@ const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
> .set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
> };
> EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_lucid_ops);
> +
> +void clk_agera_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
> + const struct alpha_pll_config *config)
> +{
> + if (config->l)
> + regmap_write(regmap, PLL_L_VAL(pll), config->l);
> +
> + if (config->alpha)
> + regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
> +
> + if (config->user_ctl_val)
> + regmap_write(regmap, PLL_USER_CTL(pll), config->user_ctl_val);
> +
> + if (config->config_ctl_val)
> + regmap_write(regmap, PLL_CONFIG_CTL(pll),
> + config->config_ctl_val);
> +
> + if (config->config_ctl_hi_val)
> + regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
> + config->config_ctl_hi_val);
> +
> + if (config->test_ctl_val)
> + regmap_write(regmap, PLL_TEST_CTL(pll),
> + config->test_ctl_val);
> +
> + if (config->test_ctl_hi_val)
> + regmap_write(regmap, PLL_TEST_CTL_U(pll),
> + config->test_ctl_hi_val);
> +}
> +EXPORT_SYMBOL_GPL(clk_agera_pll_configure);
> +
> +static int alpha_pll_agera_set_rate(struct clk_hw *hw, unsigned long rate,
Why not clk_alpha_pll prefix? We should prefix the other PLL functions
in here with clk_alpha_ like trion and fabia
> + unsigned long prate)
> +{
> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
> + u32 l, alpha_width = pll_alpha_width(pll);
> + unsigned long rrate;
> + u64 a;
> +
> + rrate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
> +
> + /*
> + * Due to limited number of bits for fractional rate programming, the
> + * rounded up rate could be marginally higher than the requested rate.
> + */
> + if (rrate > (rate + PLL_RATE_MARGIN) || rrate < rate) {
> + pr_err("Call set rate on the PLL with rounded rates!\n");
> + return -EINVAL;
> + }
See commit f78f29079327 ("clk: qcom: alpha-pll: Make error prints more
informative") where I tried to make this better. Can you extract this
check into a function that helps us understand the error better?
> +
> + /* change L_VAL without having to go through the power on sequence */
> + regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
> + regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
> +
> + /* Ensure that the write above goes through before proceeding. */
> + mb();
regmap has an mb() in it. Remove this?
> +
> + if (clk_hw_is_enabled(hw))
> + return wait_for_pll_enable_lock(pll);
> +
> + return 0;
> +}
> +
> +const struct clk_ops clk_alpha_pll_agera_ops = {
> + .enable = clk_alpha_pll_enable,
> + .disable = clk_alpha_pll_disable,
> + .is_enabled = clk_alpha_pll_is_enabled,
> + .recalc_rate = alpha_pll_fabia_recalc_rate,
> + .round_rate = clk_alpha_pll_round_rate,
> + .set_rate = alpha_pll_agera_set_rate,
> +};
> +EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings.
[not found] ` <1599584848-15530-3-git-send-email-tdas@codeaurora.org>
@ 2020-09-15 0:15 ` Stephen Boyd
0 siblings, 0 replies; 9+ messages in thread
From: Stephen Boyd @ 2020-09-15 0:15 UTC (permalink / raw)
To: Michael Turquette, Taniya Das
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt, Taniya Das
Quoting Taniya Das (2020-09-08 10:07:27)
> The Camera Subsystem clock provider have a bunch of generic properties
> that are needed in a device tree. Add a YAML schemas for those.
>
> Add clock ids for Camera clocks which are required to bring the camera
Why capitalize camera?
> subsystem out of reset.
>
> Signed-off-by: Taniya Das <tdas@codeaurora.org>
> ---
> .../bindings/clock/qcom,sc7180-camcc.yaml | 73 +++++++++++++
> include/dt-bindings/clock/qcom,camcc-sc7180.h | 121 +++++++++++++++++++++
> 2 files changed, 194 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
> create mode 100644 include/dt-bindings/clock/qcom,camcc-sc7180.h
>
> diff --git a/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
> new file mode 100644
> index 0000000..07bd38e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml
> @@ -0,0 +1,73 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/clock/qcom,sc7180-camcc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Camera Clock & Reset Controller Binding for SC7180
> +
> +maintainers:
> + - Taniya Das <tdas@codeaurora.org>
> +
> +description: |
> + Qualcomm camera clock control module which supports the clocks, resets and
> + power domains on SC7180.
> +
> + See also:
> + - dt-bindings/clock/qcom,camcc-sc7180.h.
> +
> +properties:
> + compatible:
> + const: qcom,sc7180-camcc
> +
> + clocks:
> + items:
> + - description: Board XO source
Why do we need board XO
> + - description: Camera_ahb clock from GCC
> + - description: Camera XO clock from GCC
> +
And also the gate on XO in GCC? Presumably only the one in GCC should be
going to the camera clock controller?
> + clock-names:
> + items:
> + - const: bi_tcxo
> + - const: iface
> + - const: xo
> +
> + '#clock-cells':
> + const: 1
> +
> + '#reset-cells':
> + const: 1
> +
> + '#power-domain-cells':
> + const: 1
> +
> + reg:
> + maxItems: 1
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - clock-names
> + - '#clock-cells'
> + - '#reset-cells'
> + - '#power-domain-cells'
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> + #include <dt-bindings/clock/qcom,rpmh.h>
> + clock-controller@ad00000 {
> + compatible = "qcom,sc7180-camcc";
> + reg = <0x0ad00000 0x10000>;
> + clocks = <&rpmhcc RPMH_CXO_CLK>,
> + <&gcc GCC_CAMERA_AHB_CLK>,
> + <&gcc GCC_CAMERA_XO_CLK>;
> + clock-names = "bi_tcxo", "iface", "xo";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + #power-domain-cells = <1>;
> + };
> +...
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180
2020-09-08 17:08 ` [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180 Taniya Das
@ 2020-09-21 19:03 ` kernel test robot
0 siblings, 0 replies; 9+ messages in thread
From: kernel test robot @ 2020-09-21 19:03 UTC (permalink / raw)
To: Taniya Das, Stephen Boyd, Michael Turquette
Cc: kbuild-all, David Brown, Rajendra Nayak, linux-arm-msm,
linux-soc, linux-clk, linux-kernel, Andy Gross, devicetree
[-- Attachment #1: Type: text/plain, Size: 4353 bytes --]
Hi Taniya,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on clk/clk-next]
[also build test ERROR on v5.9-rc6 next-20200921]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Taniya-Das/clk-qcom-clk-alpha-pll-Add-support-for-controlling-Agera-PLLs/20200909-011101
base: https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git clk-next
config: h8300-allyesconfig (attached as .config)
compiler: h8300-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=h8300
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
drivers/clk/qcom/camcc-sc7180.c:36:2: warning: this decimal constant is unsigned only in ISO C90
36 | { 600000000, 3300000000, 0 },
| ^
drivers/clk/qcom/camcc-sc7180.c: In function 'cam_cc_sc7180_probe':
>> drivers/clk/qcom/camcc-sc7180.c:1672:8: error: implicit declaration of function 'pm_clk_runtime_resume'; did you mean 'pm_runtime_resume'? [-Werror=implicit-function-declaration]
1672 | ret = pm_clk_runtime_resume(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~
| pm_runtime_resume
>> drivers/clk/qcom/camcc-sc7180.c:1696:8: error: implicit declaration of function 'pm_clk_runtime_suspend'; did you mean 'pm_runtime_suspend'? [-Werror=implicit-function-declaration]
1696 | ret = pm_clk_runtime_suspend(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~
| pm_runtime_suspend
cc1: some warnings being treated as errors
# https://github.com/0day-ci/linux/commit/05a7fc252efe1fcdd278d22893ea689d8b5f1f1e
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Taniya-Das/clk-qcom-clk-alpha-pll-Add-support-for-controlling-Agera-PLLs/20200909-011101
git checkout 05a7fc252efe1fcdd278d22893ea689d8b5f1f1e
vim +1672 drivers/clk/qcom/camcc-sc7180.c
1649
1650 static int cam_cc_sc7180_probe(struct platform_device *pdev)
1651 {
1652 struct regmap *regmap;
1653 int ret;
1654
1655 pm_runtime_enable(&pdev->dev);
1656 ret = pm_clk_create(&pdev->dev);
1657 if (ret)
1658 return ret;
1659
1660 ret = pm_clk_add(&pdev->dev, "xo");
1661 if (ret < 0) {
1662 dev_err(&pdev->dev, "Failed to acquire XO clock\n");
1663 goto disable_pm_runtime;
1664 }
1665
1666 ret = pm_clk_add(&pdev->dev, "iface");
1667 if (ret < 0) {
1668 dev_err(&pdev->dev, "Failed to acquire iface clock\n");
1669 goto disable_pm_runtime;
1670 }
1671
> 1672 ret = pm_clk_runtime_resume(&pdev->dev);
1673 if (ret) {
1674 dev_err(&pdev->dev, "pm runtime resume failed\n");
1675 goto destroy_pm_clk;
1676 }
1677
1678 regmap = qcom_cc_map(pdev, &cam_cc_sc7180_desc);
1679 if (IS_ERR(regmap)) {
1680 ret = PTR_ERR(regmap);
1681 goto destroy_pm_clk;
1682 }
1683
1684 clk_fabia_pll_configure(&cam_cc_pll0, regmap, &cam_cc_pll0_config);
1685 clk_fabia_pll_configure(&cam_cc_pll1, regmap, &cam_cc_pll1_config);
1686 clk_agera_pll_configure(&cam_cc_pll2, regmap, &cam_cc_pll2_config);
1687 clk_fabia_pll_configure(&cam_cc_pll3, regmap, &cam_cc_pll3_config);
1688
1689 ret = qcom_cc_really_probe(pdev, &cam_cc_sc7180_desc, regmap);
1690 if (ret) {
1691 dev_err(&pdev->dev, "Failed to register CAM CC clocks\n");
1692 goto suspend_pm_runtime;
1693 }
1694
1695 suspend_pm_runtime:
> 1696 ret = pm_clk_runtime_suspend(&pdev->dev);
1697 if (ret)
1698 dev_err(&pdev->dev, "pm runtime suspend failed\n");
1699
1700 return 0;
1701
1702 destroy_pm_clk:
1703 pm_clk_destroy(&pdev->dev);
1704
1705 disable_pm_runtime:
1706 pm_runtime_disable(&pdev->dev);
1707
1708 return ret;
1709 }
1710
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 56305 bytes --]
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180
@ 2020-09-21 19:03 ` kernel test robot
0 siblings, 0 replies; 9+ messages in thread
From: kernel test robot @ 2020-09-21 19:03 UTC (permalink / raw)
To: kbuild-all
[-- Attachment #1: Type: text/plain, Size: 4466 bytes --]
Hi Taniya,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on clk/clk-next]
[also build test ERROR on v5.9-rc6 next-20200921]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Taniya-Das/clk-qcom-clk-alpha-pll-Add-support-for-controlling-Agera-PLLs/20200909-011101
base: https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git clk-next
config: h8300-allyesconfig (attached as .config)
compiler: h8300-linux-gcc (GCC) 9.3.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-9.3.0 make.cross ARCH=h8300
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
drivers/clk/qcom/camcc-sc7180.c:36:2: warning: this decimal constant is unsigned only in ISO C90
36 | { 600000000, 3300000000, 0 },
| ^
drivers/clk/qcom/camcc-sc7180.c: In function 'cam_cc_sc7180_probe':
>> drivers/clk/qcom/camcc-sc7180.c:1672:8: error: implicit declaration of function 'pm_clk_runtime_resume'; did you mean 'pm_runtime_resume'? [-Werror=implicit-function-declaration]
1672 | ret = pm_clk_runtime_resume(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~
| pm_runtime_resume
>> drivers/clk/qcom/camcc-sc7180.c:1696:8: error: implicit declaration of function 'pm_clk_runtime_suspend'; did you mean 'pm_runtime_suspend'? [-Werror=implicit-function-declaration]
1696 | ret = pm_clk_runtime_suspend(&pdev->dev);
| ^~~~~~~~~~~~~~~~~~~~~~
| pm_runtime_suspend
cc1: some warnings being treated as errors
# https://github.com/0day-ci/linux/commit/05a7fc252efe1fcdd278d22893ea689d8b5f1f1e
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Taniya-Das/clk-qcom-clk-alpha-pll-Add-support-for-controlling-Agera-PLLs/20200909-011101
git checkout 05a7fc252efe1fcdd278d22893ea689d8b5f1f1e
vim +1672 drivers/clk/qcom/camcc-sc7180.c
1649
1650 static int cam_cc_sc7180_probe(struct platform_device *pdev)
1651 {
1652 struct regmap *regmap;
1653 int ret;
1654
1655 pm_runtime_enable(&pdev->dev);
1656 ret = pm_clk_create(&pdev->dev);
1657 if (ret)
1658 return ret;
1659
1660 ret = pm_clk_add(&pdev->dev, "xo");
1661 if (ret < 0) {
1662 dev_err(&pdev->dev, "Failed to acquire XO clock\n");
1663 goto disable_pm_runtime;
1664 }
1665
1666 ret = pm_clk_add(&pdev->dev, "iface");
1667 if (ret < 0) {
1668 dev_err(&pdev->dev, "Failed to acquire iface clock\n");
1669 goto disable_pm_runtime;
1670 }
1671
> 1672 ret = pm_clk_runtime_resume(&pdev->dev);
1673 if (ret) {
1674 dev_err(&pdev->dev, "pm runtime resume failed\n");
1675 goto destroy_pm_clk;
1676 }
1677
1678 regmap = qcom_cc_map(pdev, &cam_cc_sc7180_desc);
1679 if (IS_ERR(regmap)) {
1680 ret = PTR_ERR(regmap);
1681 goto destroy_pm_clk;
1682 }
1683
1684 clk_fabia_pll_configure(&cam_cc_pll0, regmap, &cam_cc_pll0_config);
1685 clk_fabia_pll_configure(&cam_cc_pll1, regmap, &cam_cc_pll1_config);
1686 clk_agera_pll_configure(&cam_cc_pll2, regmap, &cam_cc_pll2_config);
1687 clk_fabia_pll_configure(&cam_cc_pll3, regmap, &cam_cc_pll3_config);
1688
1689 ret = qcom_cc_really_probe(pdev, &cam_cc_sc7180_desc, regmap);
1690 if (ret) {
1691 dev_err(&pdev->dev, "Failed to register CAM CC clocks\n");
1692 goto suspend_pm_runtime;
1693 }
1694
1695 suspend_pm_runtime:
> 1696 ret = pm_clk_runtime_suspend(&pdev->dev);
1697 if (ret)
1698 dev_err(&pdev->dev, "pm runtime suspend failed\n");
1699
1700 return 0;
1701
1702 destroy_pm_clk:
1703 pm_clk_destroy(&pdev->dev);
1704
1705 disable_pm_runtime:
1706 pm_runtime_disable(&pdev->dev);
1707
1708 return ret;
1709 }
1710
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
[-- Attachment #2: config.gz --]
[-- Type: application/gzip, Size: 56305 bytes --]
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs
2020-09-15 0:13 ` [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs Stephen Boyd
@ 2020-10-13 17:03 ` Taniya Das
0 siblings, 0 replies; 9+ messages in thread
From: Taniya Das @ 2020-10-13 17:03 UTC (permalink / raw)
To: Stephen Boyd, Michael Turquette
Cc: David Brown, Rajendra Nayak, linux-arm-msm, linux-soc, linux-clk,
linux-kernel, Andy Gross, devicetree, robh, robh+dt
Thanks for the review Stephen.
On 9/15/2020 5:43 AM, Stephen Boyd wrote:
> Quoting Taniya Das (2020-09-08 10:07:26)
>> diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
>> index 26139ef..fb27fcf 100644
>> --- a/drivers/clk/qcom/clk-alpha-pll.c
>> +++ b/drivers/clk/qcom/clk-alpha-pll.c
>> @@ -1561,3 +1571,75 @@ const struct clk_ops clk_alpha_pll_postdiv_lucid_ops = {
>> .set_rate = clk_alpha_pll_postdiv_fabia_set_rate,
>> };
>> EXPORT_SYMBOL_GPL(clk_alpha_pll_postdiv_lucid_ops);
>> +
>> +void clk_agera_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
>> + const struct alpha_pll_config *config)
>> +{
>> + if (config->l)
>> + regmap_write(regmap, PLL_L_VAL(pll), config->l);
>> +
>> + if (config->alpha)
>> + regmap_write(regmap, PLL_ALPHA_VAL(pll), config->alpha);
>> +
>> + if (config->user_ctl_val)
>> + regmap_write(regmap, PLL_USER_CTL(pll), config->user_ctl_val);
>> +
>> + if (config->config_ctl_val)
>> + regmap_write(regmap, PLL_CONFIG_CTL(pll),
>> + config->config_ctl_val);
>> +
>> + if (config->config_ctl_hi_val)
>> + regmap_write(regmap, PLL_CONFIG_CTL_U(pll),
>> + config->config_ctl_hi_val);
>> +
>> + if (config->test_ctl_val)
>> + regmap_write(regmap, PLL_TEST_CTL(pll),
>> + config->test_ctl_val);
>> +
>> + if (config->test_ctl_hi_val)
>> + regmap_write(regmap, PLL_TEST_CTL_U(pll),
>> + config->test_ctl_hi_val);
>> +}
>> +EXPORT_SYMBOL_GPL(clk_agera_pll_configure);
>> +
>> +static int alpha_pll_agera_set_rate(struct clk_hw *hw, unsigned long rate,
>
> Why not clk_alpha_pll prefix? We should prefix the other PLL functions
> in here with clk_alpha_ like trion and fabia
>
Yes, I will update this in the next patch.
>> + unsigned long prate)
>> +{
>> + struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
>> + u32 l, alpha_width = pll_alpha_width(pll);
>> + unsigned long rrate;
>> + u64 a;
>> +
>> + rrate = alpha_pll_round_rate(rate, prate, &l, &a, alpha_width);
>> +
>> + /*
>> + * Due to limited number of bits for fractional rate programming, the
>> + * rounded up rate could be marginally higher than the requested rate.
>> + */
>> + if (rrate > (rate + PLL_RATE_MARGIN) || rrate < rate) {
>> + pr_err("Call set rate on the PLL with rounded rates!\n");
>> + return -EINVAL;
>> + }
>
> See commit f78f29079327 ("clk: qcom: alpha-pll: Make error prints more
> informative") where I tried to make this better. Can you extract this
> check into a function that helps us understand the error better?
>
Updated to follow the same.
>> +
>> + /* change L_VAL without having to go through the power on sequence */
>> + regmap_write(pll->clkr.regmap, PLL_L_VAL(pll), l);
>> + regmap_write(pll->clkr.regmap, PLL_ALPHA_VAL(pll), a);
>> +
>> + /* Ensure that the write above goes through before proceeding. */
>> + mb();
>
> regmap has an mb() in it. Remove this?
>
Yes, will remove it.
>> +
>> + if (clk_hw_is_enabled(hw))
>> + return wait_for_pll_enable_lock(pll);
>> +
>> + return 0;
>> +}
>> +
>> +const struct clk_ops clk_alpha_pll_agera_ops = {
>> + .enable = clk_alpha_pll_enable,
>> + .disable = clk_alpha_pll_disable,
>> + .is_enabled = clk_alpha_pll_is_enabled,
>> + .recalc_rate = alpha_pll_fabia_recalc_rate,
>> + .round_rate = clk_alpha_pll_round_rate,
>> + .set_rate = alpha_pll_agera_set_rate,
>> +};
>> +EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.
--
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2020-10-13 17:05 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <1599584848-15530-1-git-send-email-tdas@codeaurora.org>
2020-09-08 17:07 ` [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs Taniya Das
2020-09-08 17:07 ` [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings Taniya Das
2020-09-08 17:08 ` [PATCH v1 3/3] clk: qcom: camcc: Add camera clock controller driver for SC7180 Taniya Das
2020-09-21 19:03 ` kernel test robot
2020-09-21 19:03 ` kernel test robot
2020-09-08 21:41 ` [PATCH v1 0/3] Add Camera " Stephen Boyd
[not found] ` <1599584848-15530-2-git-send-email-tdas@codeaurora.org>
2020-09-15 0:13 ` [PATCH v1 1/3] clk: qcom: clk-alpha-pll: Add support for controlling Agera PLLs Stephen Boyd
2020-10-13 17:03 ` Taniya Das
[not found] ` <1599584848-15530-3-git-send-email-tdas@codeaurora.org>
2020-09-15 0:15 ` [PATCH v1 2/3] dt-bindings: clock: Add YAML schemas for the QCOM Camera clock bindings Stephen Boyd
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.