* USB bug on BCM6318
@ 2020-04-22 7:05 xchetah
0 siblings, 0 replies; 4+ messages in thread
From: xchetah @ 2020-04-22 7:05 UTC (permalink / raw)
To: linux-usb
Hi
I’m using openwrt on bcm63xx bcm6318 sagemcom F@ST 2704N V1.
the router is actually V1.1 (16MB flash , 64MB RAM).
trying to connect a usb wifi dongle as AP
lsusb -v
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.171 ohci_hcd
iProduct 2 Generic Platform OHCI controller
iSerial 1 ohci-platform
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 1
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370
Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x148f Ralink Technology, Corp.
idProduct 0x5370 RT5370 Wireless Adapter
bcdDevice 1.01
iManufacturer 1 Ralink
iProduct 2 802.11 n WLAN
iSerial 3 1.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.171 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 ehci-platform
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 1
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Device Status: 0x0001
Self Powered
the problem is that there’s no connectivity at all , I can connect to
the AP (only without encryption ) and the ssid doesn’t always show on my
mobile phone.
the usb port is working fine , I tried mounting a usb flash drive with
no problem.
also the adapter is working , I tried it on Orange pi , Raspberrypi ,
bcm6328 , all with openwrt installed on them and didn’t have any problem .
I guess it is something related to bcm6318 or its architecture code .
the onboard broadcom pci wifi is working .
I suspected that its a power problem so I added an external usb power ,
but with same issues.
also I tried openwrt 19 ,18 ,17 with same problem.
I’m also using two bcm6328 routers as point to point wifi 5ghz link with
Ralink RT5572 chipset ( rt2800usb driver ) withouyt any problem.
dmesg is filled with :
[ 1269.191198] rt2800usb_tx_sta_fifo_read_completed: 13054 callbacks
suppressed
[ 1269.191239] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.208421] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.218373] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.228285] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.238151] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.248029] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.257902] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.267793] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.278183] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.287995] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
using rmmod to remove rt2800usb module results in kernel crash
/sometimes hang and sometimes panic and reboot.
steps to reproduce:
-boot the router with usb wifi dongle
-configure it as access point or client mode and enable it
- dmesg log starts to fill and adapter is not working
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: USB BUG on BCM6318
2020-04-23 9:06 ` Oliver Neukum
@ 2020-04-23 22:20 ` xchetah
0 siblings, 0 replies; 4+ messages in thread
From: xchetah @ 2020-04-23 22:20 UTC (permalink / raw)
To: Oliver Neukum, linux-usb
On 4/23/20 12:06 PM, Oliver Neukum wrote:
> Am Mittwoch, den 22.04.2020, 19:45 +0300 schrieb xchetah:
>
> Hi,
>
> which kernel version?
>
>> the problem is that there’s no connectivity at all , I can connect to
>> the AP (only without encryption ) and the ssid doesn’t always show on my
>> mobile phone.
>> the usb port is working fine , I tried mounting a usb flash drive with
>> no problem.
>> also the adapter is working , I tried it on Orange pi , Raspberrypi ,
>> bcm6328 , all with openwrt installed on them and didn’t have any problem .
>> I guess it is something related to bcm6318 or its architecture code .
>> the onboard broadcom pci wifi is working .
>> I suspected that its a power problem so I added an external usb power ,
>> but with same issues.
>> also I tried openwrt 19 ,18 ,17 with same problem.
>> I’m also using two bcm6328 routers as point to point wifi 5ghz link with
>> Ralink RT5572 chipset ( rt2800usb driver ) withouyt any problem.
>> dmesg is filled with :
>>
>> [ 1269.191198] rt2800usb_tx_sta_fifo_read_completed: 13054 callbacks
>> suppressed
>> [ 1269.191239] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
>> Warning - TX status read failed -32
> -EPIPE. Something is stalled. The cause is unknown. What is the very
> first error during the enumeration process?
>
> Regards
> Oliver
>
kernel version : 4.14.171 , also tried testing kernel 5.4 with the same
results.
there's no error during enumeration , errors occur as soon as I activate
the device in AP mode or client mode , if the device is doing nothing I
get no errors.
usb works fine with usb storage , I tried another adapter with rt2800
driver and got the same exact problem.
Regards
Eyad
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: USB BUG on BCM6318
2020-04-22 16:45 USB BUG " xchetah
@ 2020-04-23 9:06 ` Oliver Neukum
2020-04-23 22:20 ` xchetah
0 siblings, 1 reply; 4+ messages in thread
From: Oliver Neukum @ 2020-04-23 9:06 UTC (permalink / raw)
To: xchetah, linux-usb
Am Mittwoch, den 22.04.2020, 19:45 +0300 schrieb xchetah:
>
Hi,
which kernel version?
> the problem is that there’s no connectivity at all , I can connect to
> the AP (only without encryption ) and the ssid doesn’t always show on my
> mobile phone.
> the usb port is working fine , I tried mounting a usb flash drive with
> no problem.
> also the adapter is working , I tried it on Orange pi , Raspberrypi ,
> bcm6328 , all with openwrt installed on them and didn’t have any problem .
> I guess it is something related to bcm6318 or its architecture code .
> the onboard broadcom pci wifi is working .
> I suspected that its a power problem so I added an external usb power ,
> but with same issues.
> also I tried openwrt 19 ,18 ,17 with same problem.
> I’m also using two bcm6328 routers as point to point wifi 5ghz link with
> Ralink RT5572 chipset ( rt2800usb driver ) withouyt any problem.
> dmesg is filled with :
>
> [ 1269.191198] rt2800usb_tx_sta_fifo_read_completed: 13054 callbacks
> suppressed
> [ 1269.191239] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
> Warning - TX status read failed -32
-EPIPE. Something is stalled. The cause is unknown. What is the very
first error during the enumeration process?
Regards
Oliver
^ permalink raw reply [flat|nested] 4+ messages in thread
* USB BUG on BCM6318
@ 2020-04-22 16:45 xchetah
2020-04-23 9:06 ` Oliver Neukum
0 siblings, 1 reply; 4+ messages in thread
From: xchetah @ 2020-04-22 16:45 UTC (permalink / raw)
To: linux-usb
Hi
I’m using openwrt on bcm63xx bcm6318 sagemcom F@ST 2704N V1.
the router is actually V1.1 (16MB flash , 64MB RAM).
trying to connect a usb wifi dongle as AP
lsusb -v
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.171 ohci_hcd
iProduct 2 Generic Platform OHCI controller
iSerial 1 ohci-platform
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 1
wHubCharacteristic 0x0002
No power switching (usb 1.0)
Ganged overcurrent protection
bPwrOn2PwrGood 2 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Device Status: 0x0001
Self Powered
Bus 001 Device 002: ID 148f:5370 Ralink Technology, Corp. RT5370
Wireless Adapter
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x148f Ralink Technology, Corp.
idProduct 0x5370 RT5370 Wireless Adapter
bcdDevice 1.01
iManufacturer 1 Ralink
iProduct 2 802.11 n WLAN
iSerial 3 1.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 450mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 1.0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x06 EP 6 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 4.14
iManufacturer 3 Linux 4.14.171 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 ehci-platform
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 1
wHubCharacteristic 0x0009
Per-port power switching
Per-port overcurrent protection
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x00
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0503 highspeed power enable connect
Device Status: 0x0001
Self Powered
the problem is that there’s no connectivity at all , I can connect to
the AP (only without encryption ) and the ssid doesn’t always show on my
mobile phone.
the usb port is working fine , I tried mounting a usb flash drive with
no problem.
also the adapter is working , I tried it on Orange pi , Raspberrypi ,
bcm6328 , all with openwrt installed on them and didn’t have any problem .
I guess it is something related to bcm6318 or its architecture code .
the onboard broadcom pci wifi is working .
I suspected that its a power problem so I added an external usb power ,
but with same issues.
also I tried openwrt 19 ,18 ,17 with same problem.
I’m also using two bcm6328 routers as point to point wifi 5ghz link with
Ralink RT5572 chipset ( rt2800usb driver ) withouyt any problem.
dmesg is filled with :
[ 1269.191198] rt2800usb_tx_sta_fifo_read_completed: 13054 callbacks
suppressed
[ 1269.191239] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.208421] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.218373] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.228285] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.238151] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.248029] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.257902] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.267793] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.278183] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
[ 1269.287995] ieee80211 phy1: rt2800usb_tx_sta_fifo_read_completed:
Warning - TX status read failed -32
using rmmod to remove rt2800usb module results in kernel crash
/sometimes hang and sometimes panic and reboot.
steps to reproduce:
-boot the router with usb wifi dongle
-configure it as access point or client mode and enable it
- dmesg log starts to fill and adapter is not working
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-04-23 22:20 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-22 7:05 USB bug on BCM6318 xchetah
2020-04-22 16:45 USB BUG " xchetah
2020-04-23 9:06 ` Oliver Neukum
2020-04-23 22:20 ` xchetah
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.