* [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode()
@ 2022-04-22 23:45 ` Kuogee Hsieh
0 siblings, 0 replies; 42+ messages in thread
From: Kuogee Hsieh @ 2022-04-22 23:45 UTC (permalink / raw)
To: robdclark, sean, swboyd, vkoul, daniel, airlied, agross,
dmitry.baryshkov, bjorn.andersson
Cc: quic_abhinavk, quic_aravindh, quic_khsieh, quic_sbillaka,
freedreno, dri-devel, linux-arm-msm, linux-kernel
Current DP driver implementation has adding safe mode done at
dp_hpd_plug_handle() which is expected to be executed under event
thread context.
However there is possible circular locking happen (see blow stack trace)
after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which
is executed under drm_thread context.
To break this circular locking, this patch have safe mode added at
dp_connector_get_mode() which is executed under drm thread context.
Therefore no lock acquired required for &dev->mode_config.mutex while
adding fail safe mode since it has been hold by drm thread already.
======================================================
WARNING: possible circular locking dependency detected
5.15.35-lockdep #6 Tainted: G W
------------------------------------------------------
frecon/429 is trying to acquire lock:
ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at:
dp_panel_add_fail_safe_mode+0x4c/0xa0
but task is already holding lock:
ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&kms->commit_lock[i]){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
lock_crtcs+0xb4/0x124
msm_atomic_commit_tail+0x330/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #2 (crtc_ww_class_mutex){+.+.}-{3:3}:
__mutex_lock_common+0x174/0x1a64
ww_mutex_lock+0xb8/0x278
modeset_lock+0x304/0x4ac
drm_modeset_lock+0x4c/0x7c
drmm_mode_config_init+0x4a8/0xc50
msm_drm_init+0x274/0xac0
msm_drm_bind+0x20/0x2c
try_to_bring_up_master+0x3dc/0x470
__component_add+0x18c/0x3c0
component_add+0x1c/0x28
dp_display_probe+0x954/0xa98
platform_probe+0x124/0x15c
really_probe+0x1b0/0x5f8
__driver_probe_device+0x174/0x20c
driver_probe_device+0x70/0x134
__device_attach_driver+0x130/0x1d0
bus_for_each_drv+0xfc/0x14c
__device_attach+0x1bc/0x2bc
device_initial_probe+0x1c/0x28
bus_probe_device+0x94/0x178
deferred_probe_work_func+0x1a4/0x1f0
process_one_work+0x5d4/0x9dc
worker_thread+0x898/0xccc
kthread+0x2d4/0x3d4
ret_from_fork+0x10/0x20
-> #1 (crtc_ww_class_acquire){+.+.}-{0:0}:
ww_acquire_init+0x1c4/0x2c8
drm_modeset_acquire_init+0x44/0xc8
drm_helper_probe_single_connector_modes+0xb0/0x12dc
drm_mode_getconnector+0x5dc/0xfe8
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
-> #0 (&dev->mode_config.mutex){+.+.}-{3:3}:
__lock_acquire+0x2650/0x672c
lock_acquire+0x1b4/0x4ac
__mutex_lock_common+0x174/0x1a64
mutex_lock_nested+0x98/0xac
dp_panel_add_fail_safe_mode+0x4c/0xa0
dp_hpd_plug_handle+0x1f0/0x280
dp_bridge_enable+0x94/0x2b8
drm_atomic_bridge_chain_enable+0x11c/0x168
drm_atomic_helper_commit_modeset_enables+0x500/0x740
msm_atomic_commit_tail+0x3e4/0x748
commit_tail+0x19c/0x278
drm_atomic_helper_commit+0x1dc/0x1f0
drm_atomic_commit+0xc0/0xd8
drm_atomic_helper_set_config+0xb4/0x134
drm_mode_setcrtc+0x688/0x1248
drm_ioctl_kernel+0x1e4/0x338
drm_ioctl+0x3a4/0x684
__arm64_sys_ioctl+0x118/0x154
invoke_syscall+0x78/0x224
el0_svc_common+0x178/0x200
do_el0_svc+0x94/0x13c
el0_svc+0x5c/0xec
el0t_64_sync_handler+0x78/0x108
el0t_64_sync+0x1a4/0x1a8
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
---
drivers/gpu/drm/msm/dp/dp_display.c | 6 ------
drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++----------
2 files changed, 13 insertions(+), 16 deletions(-)
diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c
index 92cd50f..01453db 100644
--- a/drivers/gpu/drm/msm/dp/dp_display.c
+++ b/drivers/gpu/drm/msm/dp/dp_display.c
@@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data)
mutex_unlock(&dp->event_mutex);
- /*
- * add fail safe mode outside event_mutex scope
- * to avoid potiential circular lock with drm thread
- */
- dp_panel_add_fail_safe_mode(dp->dp_display.connector);
-
/* uevent will complete connection part */
return 0;
};
diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c b/drivers/gpu/drm/msm/dp/dp_panel.c
index 1aa9aa8c..23fee42 100644
--- a/drivers/gpu/drm/msm/dp/dp_panel.c
+++ b/drivers/gpu/drm/msm/dp/dp_panel.c
@@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct drm_connector *connector,
return rc;
}
-void dp_panel_add_fail_safe_mode(struct drm_connector *connector)
-{
- /* fail safe edid */
- mutex_lock(&connector->dev->mode_config.mutex);
- if (drm_add_modes_noedid(connector, 640, 480))
- drm_set_preferred_mode(connector, 640, 480);
- mutex_unlock(&connector->dev->mode_config.mutex);
-}
-
int dp_panel_read_sink_caps(struct dp_panel *dp_panel,
struct drm_connector *connector)
{
@@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel *dp_panel,
goto end;
}
- dp_panel_add_fail_safe_mode(connector);
+ /* fail safe edid */
+ mutex_lock(&connector->dev->mode_config.mutex);
+ if (drm_add_modes_noedid(connector, 640, 480))
+ drm_set_preferred_mode(connector, 640, 480);
+ mutex_unlock(&connector->dev->mode_config.mutex);
}
if (panel->aux_cfg_update_done) {
@@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel,
return -EINVAL;
}
+ /*
+ * add fail safe mode (640x480) here
+ * since we are executed in drm_thread context,
+ * no mode_config.mutex acquired required
+ */
+ if (drm_add_modes_noedid(connector, 640, 480))
+ drm_set_preferred_mode(connector, 640, 480);
+
if (dp_panel->edid)
return dp_panel_update_modes(connector, dp_panel->edid);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 42+ messages in thread* [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-22 23:45 ` Kuogee Hsieh 0 siblings, 0 replies; 42+ messages in thread From: Kuogee Hsieh @ 2022-04-22 23:45 UTC (permalink / raw) To: robdclark, sean, swboyd, vkoul, daniel, airlied, agross, dmitry.baryshkov, bjorn.andersson Cc: quic_sbillaka, linux-arm-msm, quic_abhinavk, dri-devel, quic_khsieh, quic_aravindh, freedreno, linux-kernel Current DP driver implementation has adding safe mode done at dp_hpd_plug_handle() which is expected to be executed under event thread context. However there is possible circular locking happen (see blow stack trace) after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which is executed under drm_thread context. To break this circular locking, this patch have safe mode added at dp_connector_get_mode() which is executed under drm thread context. Therefore no lock acquired required for &dev->mode_config.mutex while adding fail safe mode since it has been hold by drm thread already. ====================================================== WARNING: possible circular locking dependency detected 5.15.35-lockdep #6 Tainted: G W ------------------------------------------------------ frecon/429 is trying to acquire lock: ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: dp_panel_add_fail_safe_mode+0x4c/0xa0 but task is already holding lock: ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: __mutex_lock_common+0x174/0x1a64 mutex_lock_nested+0x98/0xac lock_crtcs+0xb4/0x124 msm_atomic_commit_tail+0x330/0x748 commit_tail+0x19c/0x278 drm_atomic_helper_commit+0x1dc/0x1f0 drm_atomic_commit+0xc0/0xd8 drm_atomic_helper_set_config+0xb4/0x134 drm_mode_setcrtc+0x688/0x1248 drm_ioctl_kernel+0x1e4/0x338 drm_ioctl+0x3a4/0x684 __arm64_sys_ioctl+0x118/0x154 invoke_syscall+0x78/0x224 el0_svc_common+0x178/0x200 do_el0_svc+0x94/0x13c el0_svc+0x5c/0xec el0t_64_sync_handler+0x78/0x108 el0t_64_sync+0x1a4/0x1a8 -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: __mutex_lock_common+0x174/0x1a64 ww_mutex_lock+0xb8/0x278 modeset_lock+0x304/0x4ac drm_modeset_lock+0x4c/0x7c drmm_mode_config_init+0x4a8/0xc50 msm_drm_init+0x274/0xac0 msm_drm_bind+0x20/0x2c try_to_bring_up_master+0x3dc/0x470 __component_add+0x18c/0x3c0 component_add+0x1c/0x28 dp_display_probe+0x954/0xa98 platform_probe+0x124/0x15c really_probe+0x1b0/0x5f8 __driver_probe_device+0x174/0x20c driver_probe_device+0x70/0x134 __device_attach_driver+0x130/0x1d0 bus_for_each_drv+0xfc/0x14c __device_attach+0x1bc/0x2bc device_initial_probe+0x1c/0x28 bus_probe_device+0x94/0x178 deferred_probe_work_func+0x1a4/0x1f0 process_one_work+0x5d4/0x9dc worker_thread+0x898/0xccc kthread+0x2d4/0x3d4 ret_from_fork+0x10/0x20 -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: ww_acquire_init+0x1c4/0x2c8 drm_modeset_acquire_init+0x44/0xc8 drm_helper_probe_single_connector_modes+0xb0/0x12dc drm_mode_getconnector+0x5dc/0xfe8 drm_ioctl_kernel+0x1e4/0x338 drm_ioctl+0x3a4/0x684 __arm64_sys_ioctl+0x118/0x154 invoke_syscall+0x78/0x224 el0_svc_common+0x178/0x200 do_el0_svc+0x94/0x13c el0_svc+0x5c/0xec el0t_64_sync_handler+0x78/0x108 el0t_64_sync+0x1a4/0x1a8 -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: __lock_acquire+0x2650/0x672c lock_acquire+0x1b4/0x4ac __mutex_lock_common+0x174/0x1a64 mutex_lock_nested+0x98/0xac dp_panel_add_fail_safe_mode+0x4c/0xa0 dp_hpd_plug_handle+0x1f0/0x280 dp_bridge_enable+0x94/0x2b8 drm_atomic_bridge_chain_enable+0x11c/0x168 drm_atomic_helper_commit_modeset_enables+0x500/0x740 msm_atomic_commit_tail+0x3e4/0x748 commit_tail+0x19c/0x278 drm_atomic_helper_commit+0x1dc/0x1f0 drm_atomic_commit+0xc0/0xd8 drm_atomic_helper_set_config+0xb4/0x134 drm_mode_setcrtc+0x688/0x1248 drm_ioctl_kernel+0x1e4/0x338 drm_ioctl+0x3a4/0x684 __arm64_sys_ioctl+0x118/0x154 invoke_syscall+0x78/0x224 el0_svc_common+0x178/0x200 do_el0_svc+0x94/0x13c el0_svc+0x5c/0xec el0t_64_sync_handler+0x78/0x108 el0t_64_sync+0x1a4/0x1a8 Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> --- drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- 2 files changed, 13 insertions(+), 16 deletions(-) diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c index 92cd50f..01453db 100644 --- a/drivers/gpu/drm/msm/dp/dp_display.c +++ b/drivers/gpu/drm/msm/dp/dp_display.c @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data) mutex_unlock(&dp->event_mutex); - /* - * add fail safe mode outside event_mutex scope - * to avoid potiential circular lock with drm thread - */ - dp_panel_add_fail_safe_mode(dp->dp_display.connector); - /* uevent will complete connection part */ return 0; }; diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c b/drivers/gpu/drm/msm/dp/dp_panel.c index 1aa9aa8c..23fee42 100644 --- a/drivers/gpu/drm/msm/dp/dp_panel.c +++ b/drivers/gpu/drm/msm/dp/dp_panel.c @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct drm_connector *connector, return rc; } -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) -{ - /* fail safe edid */ - mutex_lock(&connector->dev->mode_config.mutex); - if (drm_add_modes_noedid(connector, 640, 480)) - drm_set_preferred_mode(connector, 640, 480); - mutex_unlock(&connector->dev->mode_config.mutex); -} - int dp_panel_read_sink_caps(struct dp_panel *dp_panel, struct drm_connector *connector) { @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel *dp_panel, goto end; } - dp_panel_add_fail_safe_mode(connector); + /* fail safe edid */ + mutex_lock(&connector->dev->mode_config.mutex); + if (drm_add_modes_noedid(connector, 640, 480)) + drm_set_preferred_mode(connector, 640, 480); + mutex_unlock(&connector->dev->mode_config.mutex); } if (panel->aux_cfg_update_done) { @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, return -EINVAL; } + /* + * add fail safe mode (640x480) here + * since we are executed in drm_thread context, + * no mode_config.mutex acquired required + */ + if (drm_add_modes_noedid(connector, 640, 480)) + drm_set_preferred_mode(connector, 640, 480); + if (dp_panel->edid) return dp_panel_update_modes(connector, dp_panel->edid); -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project ^ permalink raw reply related [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-22 23:45 ` Kuogee Hsieh @ 2022-04-23 0:02 ` Stephen Boyd -1 siblings, 0 replies; 42+ messages in thread From: Stephen Boyd @ 2022-04-23 0:02 UTC (permalink / raw) To: Kuogee Hsieh, agross, airlied, bjorn.andersson, daniel, dmitry.baryshkov, robdclark, sean, vkoul Cc: quic_abhinavk, quic_aravindh, quic_sbillaka, freedreno, dri-devel, linux-arm-msm, linux-kernel Quoting Kuogee Hsieh (2022-04-22 16:45:23) > Current DP driver implementation has adding safe mode done at > dp_hpd_plug_handle() which is expected to be executed under event > thread context. > > However there is possible circular locking happen (see blow stack trace) > after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > is executed under drm_thread context. > > To break this circular locking, this patch have safe mode added at > dp_connector_get_mode() which is executed under drm thread context. > Therefore no lock acquired required for &dev->mode_config.mutex while > adding fail safe mode since it has been hold by drm thread already. Reported-by: Douglas Anderson <dianders@chromium.org> Fixes: 8b2c181e3dcf ("drm/msm/dp: add fail safe mode outside of event_mutex context") Reviewed-by: Stephen Boyd <swboyd@chromium.org> ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-23 0:02 ` Stephen Boyd 0 siblings, 0 replies; 42+ messages in thread From: Stephen Boyd @ 2022-04-23 0:02 UTC (permalink / raw) To: Kuogee Hsieh, agross, airlied, bjorn.andersson, daniel, dmitry.baryshkov, robdclark, sean, vkoul Cc: quic_sbillaka, linux-arm-msm, quic_abhinavk, dri-devel, linux-kernel, quic_aravindh, freedreno Quoting Kuogee Hsieh (2022-04-22 16:45:23) > Current DP driver implementation has adding safe mode done at > dp_hpd_plug_handle() which is expected to be executed under event > thread context. > > However there is possible circular locking happen (see blow stack trace) > after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > is executed under drm_thread context. > > To break this circular locking, this patch have safe mode added at > dp_connector_get_mode() which is executed under drm thread context. > Therefore no lock acquired required for &dev->mode_config.mutex while > adding fail safe mode since it has been hold by drm thread already. Reported-by: Douglas Anderson <dianders@chromium.org> Fixes: 8b2c181e3dcf ("drm/msm/dp: add fail safe mode outside of event_mutex context") Reviewed-by: Stephen Boyd <swboyd@chromium.org> ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-22 23:45 ` Kuogee Hsieh @ 2022-04-23 0:07 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-23 0:07 UTC (permalink / raw) To: Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson Cc: quic_abhinavk, quic_aravindh, quic_sbillaka, freedreno, dri-devel, linux-arm-msm, linux-kernel On 23/04/2022 02:45, Kuogee Hsieh wrote: > Current DP driver implementation has adding safe mode done at > dp_hpd_plug_handle() which is expected to be executed under event > thread context. > > However there is possible circular locking happen (see blow stack trace) > after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > is executed under drm_thread context. > > To break this circular locking, this patch have safe mode added at > dp_connector_get_mode() which is executed under drm thread context. > Therefore no lock acquired required for &dev->mode_config.mutex while > adding fail safe mode since it has been hold by drm thread already. > > ====================================================== > WARNING: possible circular locking dependency detected > 5.15.35-lockdep #6 Tainted: G W > ------------------------------------------------------ > frecon/429 is trying to acquire lock: > ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > dp_panel_add_fail_safe_mode+0x4c/0xa0 > > but task is already holding lock: > ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124 > > which lock already depends on the new lock. > > the existing dependency chain (in reverse order) is: > > -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > __mutex_lock_common+0x174/0x1a64 > mutex_lock_nested+0x98/0xac > lock_crtcs+0xb4/0x124 > msm_atomic_commit_tail+0x330/0x748 > commit_tail+0x19c/0x278 > drm_atomic_helper_commit+0x1dc/0x1f0 > drm_atomic_commit+0xc0/0xd8 > drm_atomic_helper_set_config+0xb4/0x134 > drm_mode_setcrtc+0x688/0x1248 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > __mutex_lock_common+0x174/0x1a64 > ww_mutex_lock+0xb8/0x278 > modeset_lock+0x304/0x4ac > drm_modeset_lock+0x4c/0x7c > drmm_mode_config_init+0x4a8/0xc50 > msm_drm_init+0x274/0xac0 > msm_drm_bind+0x20/0x2c > try_to_bring_up_master+0x3dc/0x470 > __component_add+0x18c/0x3c0 > component_add+0x1c/0x28 > dp_display_probe+0x954/0xa98 > platform_probe+0x124/0x15c > really_probe+0x1b0/0x5f8 > __driver_probe_device+0x174/0x20c > driver_probe_device+0x70/0x134 > __device_attach_driver+0x130/0x1d0 > bus_for_each_drv+0xfc/0x14c > __device_attach+0x1bc/0x2bc > device_initial_probe+0x1c/0x28 > bus_probe_device+0x94/0x178 > deferred_probe_work_func+0x1a4/0x1f0 > process_one_work+0x5d4/0x9dc > worker_thread+0x898/0xccc > kthread+0x2d4/0x3d4 > ret_from_fork+0x10/0x20 > > -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > ww_acquire_init+0x1c4/0x2c8 > drm_modeset_acquire_init+0x44/0xc8 > drm_helper_probe_single_connector_modes+0xb0/0x12dc > drm_mode_getconnector+0x5dc/0xfe8 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > __lock_acquire+0x2650/0x672c > lock_acquire+0x1b4/0x4ac > __mutex_lock_common+0x174/0x1a64 > mutex_lock_nested+0x98/0xac > dp_panel_add_fail_safe_mode+0x4c/0xa0 > dp_hpd_plug_handle+0x1f0/0x280 > dp_bridge_enable+0x94/0x2b8 > drm_atomic_bridge_chain_enable+0x11c/0x168 > drm_atomic_helper_commit_modeset_enables+0x500/0x740 > msm_atomic_commit_tail+0x3e4/0x748 > commit_tail+0x19c/0x278 > drm_atomic_helper_commit+0x1dc/0x1f0 > drm_atomic_commit+0xc0/0xd8 > drm_atomic_helper_set_config+0xb4/0x134 > drm_mode_setcrtc+0x688/0x1248 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > --- > drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > 2 files changed, 13 insertions(+), 16 deletions(-) > > diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c > index 92cd50f..01453db 100644 > --- a/drivers/gpu/drm/msm/dp/dp_display.c > +++ b/drivers/gpu/drm/msm/dp/dp_display.c > @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data) > > mutex_unlock(&dp->event_mutex); > > - /* > - * add fail safe mode outside event_mutex scope > - * to avoid potiential circular lock with drm thread > - */ > - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > - > /* uevent will complete connection part */ > return 0; > }; > diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c b/drivers/gpu/drm/msm/dp/dp_panel.c > index 1aa9aa8c..23fee42 100644 > --- a/drivers/gpu/drm/msm/dp/dp_panel.c > +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct drm_connector *connector, > return rc; > } > > -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > -{ > - /* fail safe edid */ > - mutex_lock(&connector->dev->mode_config.mutex); > - if (drm_add_modes_noedid(connector, 640, 480)) > - drm_set_preferred_mode(connector, 640, 480); > - mutex_unlock(&connector->dev->mode_config.mutex); > -} > - > int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > struct drm_connector *connector) > { > @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > goto end; > } > > - dp_panel_add_fail_safe_mode(connector); > + /* fail safe edid */ > + mutex_lock(&connector->dev->mode_config.mutex); > + if (drm_add_modes_noedid(connector, 640, 480)) > + drm_set_preferred_mode(connector, 640, 480); > + mutex_unlock(&connector->dev->mode_config.mutex); > } > > if (panel->aux_cfg_update_done) { > @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > return -EINVAL; > } > > + /* > + * add fail safe mode (640x480) here > + * since we are executed in drm_thread context, > + * no mode_config.mutex acquired required > + */ > + if (drm_add_modes_noedid(connector, 640, 480)) > + drm_set_preferred_mode(connector, 640, 480); > + > if (dp_panel->edid) > return dp_panel_update_modes(connector, dp_panel->edid); > Also, wouldn't calling get_modes() several times make cause adding more and more 640x480 modes to the modes list? -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-23 0:07 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-23 0:07 UTC (permalink / raw) To: Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson Cc: quic_sbillaka, linux-arm-msm, quic_abhinavk, dri-devel, linux-kernel, quic_aravindh, freedreno On 23/04/2022 02:45, Kuogee Hsieh wrote: > Current DP driver implementation has adding safe mode done at > dp_hpd_plug_handle() which is expected to be executed under event > thread context. > > However there is possible circular locking happen (see blow stack trace) > after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > is executed under drm_thread context. > > To break this circular locking, this patch have safe mode added at > dp_connector_get_mode() which is executed under drm thread context. > Therefore no lock acquired required for &dev->mode_config.mutex while > adding fail safe mode since it has been hold by drm thread already. > > ====================================================== > WARNING: possible circular locking dependency detected > 5.15.35-lockdep #6 Tainted: G W > ------------------------------------------------------ > frecon/429 is trying to acquire lock: > ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > dp_panel_add_fail_safe_mode+0x4c/0xa0 > > but task is already holding lock: > ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124 > > which lock already depends on the new lock. > > the existing dependency chain (in reverse order) is: > > -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > __mutex_lock_common+0x174/0x1a64 > mutex_lock_nested+0x98/0xac > lock_crtcs+0xb4/0x124 > msm_atomic_commit_tail+0x330/0x748 > commit_tail+0x19c/0x278 > drm_atomic_helper_commit+0x1dc/0x1f0 > drm_atomic_commit+0xc0/0xd8 > drm_atomic_helper_set_config+0xb4/0x134 > drm_mode_setcrtc+0x688/0x1248 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > __mutex_lock_common+0x174/0x1a64 > ww_mutex_lock+0xb8/0x278 > modeset_lock+0x304/0x4ac > drm_modeset_lock+0x4c/0x7c > drmm_mode_config_init+0x4a8/0xc50 > msm_drm_init+0x274/0xac0 > msm_drm_bind+0x20/0x2c > try_to_bring_up_master+0x3dc/0x470 > __component_add+0x18c/0x3c0 > component_add+0x1c/0x28 > dp_display_probe+0x954/0xa98 > platform_probe+0x124/0x15c > really_probe+0x1b0/0x5f8 > __driver_probe_device+0x174/0x20c > driver_probe_device+0x70/0x134 > __device_attach_driver+0x130/0x1d0 > bus_for_each_drv+0xfc/0x14c > __device_attach+0x1bc/0x2bc > device_initial_probe+0x1c/0x28 > bus_probe_device+0x94/0x178 > deferred_probe_work_func+0x1a4/0x1f0 > process_one_work+0x5d4/0x9dc > worker_thread+0x898/0xccc > kthread+0x2d4/0x3d4 > ret_from_fork+0x10/0x20 > > -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > ww_acquire_init+0x1c4/0x2c8 > drm_modeset_acquire_init+0x44/0xc8 > drm_helper_probe_single_connector_modes+0xb0/0x12dc > drm_mode_getconnector+0x5dc/0xfe8 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > __lock_acquire+0x2650/0x672c > lock_acquire+0x1b4/0x4ac > __mutex_lock_common+0x174/0x1a64 > mutex_lock_nested+0x98/0xac > dp_panel_add_fail_safe_mode+0x4c/0xa0 > dp_hpd_plug_handle+0x1f0/0x280 > dp_bridge_enable+0x94/0x2b8 > drm_atomic_bridge_chain_enable+0x11c/0x168 > drm_atomic_helper_commit_modeset_enables+0x500/0x740 > msm_atomic_commit_tail+0x3e4/0x748 > commit_tail+0x19c/0x278 > drm_atomic_helper_commit+0x1dc/0x1f0 > drm_atomic_commit+0xc0/0xd8 > drm_atomic_helper_set_config+0xb4/0x134 > drm_mode_setcrtc+0x688/0x1248 > drm_ioctl_kernel+0x1e4/0x338 > drm_ioctl+0x3a4/0x684 > __arm64_sys_ioctl+0x118/0x154 > invoke_syscall+0x78/0x224 > el0_svc_common+0x178/0x200 > do_el0_svc+0x94/0x13c > el0_svc+0x5c/0xec > el0t_64_sync_handler+0x78/0x108 > el0t_64_sync+0x1a4/0x1a8 > > Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > --- > drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > 2 files changed, 13 insertions(+), 16 deletions(-) > > diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c > index 92cd50f..01453db 100644 > --- a/drivers/gpu/drm/msm/dp/dp_display.c > +++ b/drivers/gpu/drm/msm/dp/dp_display.c > @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct dp_display_private *dp, u32 data) > > mutex_unlock(&dp->event_mutex); > > - /* > - * add fail safe mode outside event_mutex scope > - * to avoid potiential circular lock with drm thread > - */ > - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > - > /* uevent will complete connection part */ > return 0; > }; > diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c b/drivers/gpu/drm/msm/dp/dp_panel.c > index 1aa9aa8c..23fee42 100644 > --- a/drivers/gpu/drm/msm/dp/dp_panel.c > +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct drm_connector *connector, > return rc; > } > > -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > -{ > - /* fail safe edid */ > - mutex_lock(&connector->dev->mode_config.mutex); > - if (drm_add_modes_noedid(connector, 640, 480)) > - drm_set_preferred_mode(connector, 640, 480); > - mutex_unlock(&connector->dev->mode_config.mutex); > -} > - > int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > struct drm_connector *connector) > { > @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > goto end; > } > > - dp_panel_add_fail_safe_mode(connector); > + /* fail safe edid */ > + mutex_lock(&connector->dev->mode_config.mutex); > + if (drm_add_modes_noedid(connector, 640, 480)) > + drm_set_preferred_mode(connector, 640, 480); > + mutex_unlock(&connector->dev->mode_config.mutex); > } > > if (panel->aux_cfg_update_done) { > @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > return -EINVAL; > } > > + /* > + * add fail safe mode (640x480) here > + * since we are executed in drm_thread context, > + * no mode_config.mutex acquired required > + */ > + if (drm_add_modes_noedid(connector, 640, 480)) > + drm_set_preferred_mode(connector, 640, 480); > + > if (dp_panel->edid) > return dp_panel_update_modes(connector, dp_panel->edid); > Also, wouldn't calling get_modes() several times make cause adding more and more 640x480 modes to the modes list? -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-23 0:07 ` Dmitry Baryshkov @ 2022-04-23 0:12 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-23 0:12 UTC (permalink / raw) To: Dmitry Baryshkov, Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson Cc: quic_sbillaka, linux-arm-msm, dri-devel, linux-kernel, quic_aravindh, freedreno On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > On 23/04/2022 02:45, Kuogee Hsieh wrote: >> Current DP driver implementation has adding safe mode done at >> dp_hpd_plug_handle() which is expected to be executed under event >> thread context. >> >> However there is possible circular locking happen (see blow stack trace) >> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >> is executed under drm_thread context. >> >> To break this circular locking, this patch have safe mode added at >> dp_connector_get_mode() which is executed under drm thread context. >> Therefore no lock acquired required for &dev->mode_config.mutex while >> adding fail safe mode since it has been hold by drm thread already. >> >> ====================================================== >> WARNING: possible circular locking dependency detected >> 5.15.35-lockdep #6 Tainted: G W >> ------------------------------------------------------ >> frecon/429 is trying to acquire lock: >> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >> dp_panel_add_fail_safe_mode+0x4c/0xa0 >> >> but task is already holding lock: >> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >> lock_crtcs+0xb4/0x124 >> >> which lock already depends on the new lock. >> >> the existing dependency chain (in reverse order) is: >> >> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >> __mutex_lock_common+0x174/0x1a64 >> mutex_lock_nested+0x98/0xac >> lock_crtcs+0xb4/0x124 >> msm_atomic_commit_tail+0x330/0x748 >> commit_tail+0x19c/0x278 >> drm_atomic_helper_commit+0x1dc/0x1f0 >> drm_atomic_commit+0xc0/0xd8 >> drm_atomic_helper_set_config+0xb4/0x134 >> drm_mode_setcrtc+0x688/0x1248 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >> __mutex_lock_common+0x174/0x1a64 >> ww_mutex_lock+0xb8/0x278 >> modeset_lock+0x304/0x4ac >> drm_modeset_lock+0x4c/0x7c >> drmm_mode_config_init+0x4a8/0xc50 >> msm_drm_init+0x274/0xac0 >> msm_drm_bind+0x20/0x2c >> try_to_bring_up_master+0x3dc/0x470 >> __component_add+0x18c/0x3c0 >> component_add+0x1c/0x28 >> dp_display_probe+0x954/0xa98 >> platform_probe+0x124/0x15c >> really_probe+0x1b0/0x5f8 >> __driver_probe_device+0x174/0x20c >> driver_probe_device+0x70/0x134 >> __device_attach_driver+0x130/0x1d0 >> bus_for_each_drv+0xfc/0x14c >> __device_attach+0x1bc/0x2bc >> device_initial_probe+0x1c/0x28 >> bus_probe_device+0x94/0x178 >> deferred_probe_work_func+0x1a4/0x1f0 >> process_one_work+0x5d4/0x9dc >> worker_thread+0x898/0xccc >> kthread+0x2d4/0x3d4 >> ret_from_fork+0x10/0x20 >> >> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >> ww_acquire_init+0x1c4/0x2c8 >> drm_modeset_acquire_init+0x44/0xc8 >> drm_helper_probe_single_connector_modes+0xb0/0x12dc >> drm_mode_getconnector+0x5dc/0xfe8 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >> __lock_acquire+0x2650/0x672c >> lock_acquire+0x1b4/0x4ac >> __mutex_lock_common+0x174/0x1a64 >> mutex_lock_nested+0x98/0xac >> dp_panel_add_fail_safe_mode+0x4c/0xa0 >> dp_hpd_plug_handle+0x1f0/0x280 >> dp_bridge_enable+0x94/0x2b8 >> drm_atomic_bridge_chain_enable+0x11c/0x168 >> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >> msm_atomic_commit_tail+0x3e4/0x748 >> commit_tail+0x19c/0x278 >> drm_atomic_helper_commit+0x1dc/0x1f0 >> drm_atomic_commit+0xc0/0xd8 >> drm_atomic_helper_set_config+0xb4/0x134 >> drm_mode_setcrtc+0x688/0x1248 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >> --- >> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >> 2 files changed, 13 insertions(+), 16 deletions(-) >> >> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >> b/drivers/gpu/drm/msm/dp/dp_display.c >> index 92cd50f..01453db 100644 >> --- a/drivers/gpu/drm/msm/dp/dp_display.c >> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >> dp_display_private *dp, u32 data) >> mutex_unlock(&dp->event_mutex); >> - /* >> - * add fail safe mode outside event_mutex scope >> - * to avoid potiential circular lock with drm thread >> - */ >> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >> - >> /* uevent will complete connection part */ >> return 0; >> }; >> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >> b/drivers/gpu/drm/msm/dp/dp_panel.c >> index 1aa9aa8c..23fee42 100644 >> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >> drm_connector *connector, >> return rc; >> } >> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >> -{ >> - /* fail safe edid */ >> - mutex_lock(&connector->dev->mode_config.mutex); >> - if (drm_add_modes_noedid(connector, 640, 480)) >> - drm_set_preferred_mode(connector, 640, 480); >> - mutex_unlock(&connector->dev->mode_config.mutex); >> -} >> - >> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >> struct drm_connector *connector) >> { >> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >> *dp_panel, >> goto end; >> } >> - dp_panel_add_fail_safe_mode(connector); >> + /* fail safe edid */ >> + mutex_lock(&connector->dev->mode_config.mutex); >> + if (drm_add_modes_noedid(connector, 640, 480)) >> + drm_set_preferred_mode(connector, 640, 480); >> + mutex_unlock(&connector->dev->mode_config.mutex); >> } >> if (panel->aux_cfg_update_done) { >> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >> return -EINVAL; >> } >> + /* >> + * add fail safe mode (640x480) here >> + * since we are executed in drm_thread context, >> + * no mode_config.mutex acquired required >> + */ >> + if (drm_add_modes_noedid(connector, 640, 480)) >> + drm_set_preferred_mode(connector, 640, 480); >> + >> if (dp_panel->edid) >> return dp_panel_update_modes(connector, dp_panel->edid); > Also, wouldn't calling get_modes() several times make cause adding more > and more 640x480 modes to the modes list? > Shouldnt DRM be blocking that here? Call should trickle down here only if count_modes was 0 if (out_resp->count_modes == 0) { if (is_current_master) connector->funcs->fill_modes(connector, dev->mode_config.max_width, dev->mode_config.max_height); else drm_dbg_kms(dev, "User-space requested a forced probe on [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", connector->base.id, connector->name); } > ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-23 0:12 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-23 0:12 UTC (permalink / raw) To: Dmitry Baryshkov, Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson Cc: quic_sbillaka, linux-arm-msm, linux-kernel, dri-devel, quic_aravindh, freedreno On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > On 23/04/2022 02:45, Kuogee Hsieh wrote: >> Current DP driver implementation has adding safe mode done at >> dp_hpd_plug_handle() which is expected to be executed under event >> thread context. >> >> However there is possible circular locking happen (see blow stack trace) >> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >> is executed under drm_thread context. >> >> To break this circular locking, this patch have safe mode added at >> dp_connector_get_mode() which is executed under drm thread context. >> Therefore no lock acquired required for &dev->mode_config.mutex while >> adding fail safe mode since it has been hold by drm thread already. >> >> ====================================================== >> WARNING: possible circular locking dependency detected >> 5.15.35-lockdep #6 Tainted: G W >> ------------------------------------------------------ >> frecon/429 is trying to acquire lock: >> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >> dp_panel_add_fail_safe_mode+0x4c/0xa0 >> >> but task is already holding lock: >> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >> lock_crtcs+0xb4/0x124 >> >> which lock already depends on the new lock. >> >> the existing dependency chain (in reverse order) is: >> >> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >> __mutex_lock_common+0x174/0x1a64 >> mutex_lock_nested+0x98/0xac >> lock_crtcs+0xb4/0x124 >> msm_atomic_commit_tail+0x330/0x748 >> commit_tail+0x19c/0x278 >> drm_atomic_helper_commit+0x1dc/0x1f0 >> drm_atomic_commit+0xc0/0xd8 >> drm_atomic_helper_set_config+0xb4/0x134 >> drm_mode_setcrtc+0x688/0x1248 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >> __mutex_lock_common+0x174/0x1a64 >> ww_mutex_lock+0xb8/0x278 >> modeset_lock+0x304/0x4ac >> drm_modeset_lock+0x4c/0x7c >> drmm_mode_config_init+0x4a8/0xc50 >> msm_drm_init+0x274/0xac0 >> msm_drm_bind+0x20/0x2c >> try_to_bring_up_master+0x3dc/0x470 >> __component_add+0x18c/0x3c0 >> component_add+0x1c/0x28 >> dp_display_probe+0x954/0xa98 >> platform_probe+0x124/0x15c >> really_probe+0x1b0/0x5f8 >> __driver_probe_device+0x174/0x20c >> driver_probe_device+0x70/0x134 >> __device_attach_driver+0x130/0x1d0 >> bus_for_each_drv+0xfc/0x14c >> __device_attach+0x1bc/0x2bc >> device_initial_probe+0x1c/0x28 >> bus_probe_device+0x94/0x178 >> deferred_probe_work_func+0x1a4/0x1f0 >> process_one_work+0x5d4/0x9dc >> worker_thread+0x898/0xccc >> kthread+0x2d4/0x3d4 >> ret_from_fork+0x10/0x20 >> >> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >> ww_acquire_init+0x1c4/0x2c8 >> drm_modeset_acquire_init+0x44/0xc8 >> drm_helper_probe_single_connector_modes+0xb0/0x12dc >> drm_mode_getconnector+0x5dc/0xfe8 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >> __lock_acquire+0x2650/0x672c >> lock_acquire+0x1b4/0x4ac >> __mutex_lock_common+0x174/0x1a64 >> mutex_lock_nested+0x98/0xac >> dp_panel_add_fail_safe_mode+0x4c/0xa0 >> dp_hpd_plug_handle+0x1f0/0x280 >> dp_bridge_enable+0x94/0x2b8 >> drm_atomic_bridge_chain_enable+0x11c/0x168 >> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >> msm_atomic_commit_tail+0x3e4/0x748 >> commit_tail+0x19c/0x278 >> drm_atomic_helper_commit+0x1dc/0x1f0 >> drm_atomic_commit+0xc0/0xd8 >> drm_atomic_helper_set_config+0xb4/0x134 >> drm_mode_setcrtc+0x688/0x1248 >> drm_ioctl_kernel+0x1e4/0x338 >> drm_ioctl+0x3a4/0x684 >> __arm64_sys_ioctl+0x118/0x154 >> invoke_syscall+0x78/0x224 >> el0_svc_common+0x178/0x200 >> do_el0_svc+0x94/0x13c >> el0_svc+0x5c/0xec >> el0t_64_sync_handler+0x78/0x108 >> el0t_64_sync+0x1a4/0x1a8 >> >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >> --- >> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >> 2 files changed, 13 insertions(+), 16 deletions(-) >> >> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >> b/drivers/gpu/drm/msm/dp/dp_display.c >> index 92cd50f..01453db 100644 >> --- a/drivers/gpu/drm/msm/dp/dp_display.c >> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >> dp_display_private *dp, u32 data) >> mutex_unlock(&dp->event_mutex); >> - /* >> - * add fail safe mode outside event_mutex scope >> - * to avoid potiential circular lock with drm thread >> - */ >> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >> - >> /* uevent will complete connection part */ >> return 0; >> }; >> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >> b/drivers/gpu/drm/msm/dp/dp_panel.c >> index 1aa9aa8c..23fee42 100644 >> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >> drm_connector *connector, >> return rc; >> } >> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >> -{ >> - /* fail safe edid */ >> - mutex_lock(&connector->dev->mode_config.mutex); >> - if (drm_add_modes_noedid(connector, 640, 480)) >> - drm_set_preferred_mode(connector, 640, 480); >> - mutex_unlock(&connector->dev->mode_config.mutex); >> -} >> - >> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >> struct drm_connector *connector) >> { >> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >> *dp_panel, >> goto end; >> } >> - dp_panel_add_fail_safe_mode(connector); >> + /* fail safe edid */ >> + mutex_lock(&connector->dev->mode_config.mutex); >> + if (drm_add_modes_noedid(connector, 640, 480)) >> + drm_set_preferred_mode(connector, 640, 480); >> + mutex_unlock(&connector->dev->mode_config.mutex); >> } >> if (panel->aux_cfg_update_done) { >> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >> return -EINVAL; >> } >> + /* >> + * add fail safe mode (640x480) here >> + * since we are executed in drm_thread context, >> + * no mode_config.mutex acquired required >> + */ >> + if (drm_add_modes_noedid(connector, 640, 480)) >> + drm_set_preferred_mode(connector, 640, 480); >> + >> if (dp_panel->edid) >> return dp_panel_update_modes(connector, dp_panel->edid); > Also, wouldn't calling get_modes() several times make cause adding more > and more 640x480 modes to the modes list? > Shouldnt DRM be blocking that here? Call should trickle down here only if count_modes was 0 if (out_resp->count_modes == 0) { if (is_current_master) connector->funcs->fill_modes(connector, dev->mode_config.max_width, dev->mode_config.max_height); else drm_dbg_kms(dev, "User-space requested a forced probe on [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", connector->base.id, connector->name); } > ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-23 0:12 ` Abhinav Kumar @ 2022-04-23 6:25 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-23 6:25 UTC (permalink / raw) To: Abhinav Kumar Cc: Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson, quic_sbillaka, linux-arm-msm, dri-devel, linux-kernel, quic_aravindh, freedreno On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > > > On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > > On 23/04/2022 02:45, Kuogee Hsieh wrote: > >> Current DP driver implementation has adding safe mode done at > >> dp_hpd_plug_handle() which is expected to be executed under event > >> thread context. > >> > >> However there is possible circular locking happen (see blow stack trace) > >> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > >> is executed under drm_thread context. > >> > >> To break this circular locking, this patch have safe mode added at > >> dp_connector_get_mode() which is executed under drm thread context. > >> Therefore no lock acquired required for &dev->mode_config.mutex while > >> adding fail safe mode since it has been hold by drm thread already. > >> > >> ====================================================== > >> WARNING: possible circular locking dependency detected > >> 5.15.35-lockdep #6 Tainted: G W > >> ------------------------------------------------------ > >> frecon/429 is trying to acquire lock: > >> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > >> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >> > >> but task is already holding lock: > >> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: > >> lock_crtcs+0xb4/0x124 > >> > >> which lock already depends on the new lock. > >> > >> the existing dependency chain (in reverse order) is: > >> > >> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > >> __mutex_lock_common+0x174/0x1a64 > >> mutex_lock_nested+0x98/0xac > >> lock_crtcs+0xb4/0x124 > >> msm_atomic_commit_tail+0x330/0x748 > >> commit_tail+0x19c/0x278 > >> drm_atomic_helper_commit+0x1dc/0x1f0 > >> drm_atomic_commit+0xc0/0xd8 > >> drm_atomic_helper_set_config+0xb4/0x134 > >> drm_mode_setcrtc+0x688/0x1248 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > >> __mutex_lock_common+0x174/0x1a64 > >> ww_mutex_lock+0xb8/0x278 > >> modeset_lock+0x304/0x4ac > >> drm_modeset_lock+0x4c/0x7c > >> drmm_mode_config_init+0x4a8/0xc50 > >> msm_drm_init+0x274/0xac0 > >> msm_drm_bind+0x20/0x2c > >> try_to_bring_up_master+0x3dc/0x470 > >> __component_add+0x18c/0x3c0 > >> component_add+0x1c/0x28 > >> dp_display_probe+0x954/0xa98 > >> platform_probe+0x124/0x15c > >> really_probe+0x1b0/0x5f8 > >> __driver_probe_device+0x174/0x20c > >> driver_probe_device+0x70/0x134 > >> __device_attach_driver+0x130/0x1d0 > >> bus_for_each_drv+0xfc/0x14c > >> __device_attach+0x1bc/0x2bc > >> device_initial_probe+0x1c/0x28 > >> bus_probe_device+0x94/0x178 > >> deferred_probe_work_func+0x1a4/0x1f0 > >> process_one_work+0x5d4/0x9dc > >> worker_thread+0x898/0xccc > >> kthread+0x2d4/0x3d4 > >> ret_from_fork+0x10/0x20 > >> > >> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > >> ww_acquire_init+0x1c4/0x2c8 > >> drm_modeset_acquire_init+0x44/0xc8 > >> drm_helper_probe_single_connector_modes+0xb0/0x12dc > >> drm_mode_getconnector+0x5dc/0xfe8 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > >> __lock_acquire+0x2650/0x672c > >> lock_acquire+0x1b4/0x4ac > >> __mutex_lock_common+0x174/0x1a64 > >> mutex_lock_nested+0x98/0xac > >> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >> dp_hpd_plug_handle+0x1f0/0x280 > >> dp_bridge_enable+0x94/0x2b8 > >> drm_atomic_bridge_chain_enable+0x11c/0x168 > >> drm_atomic_helper_commit_modeset_enables+0x500/0x740 > >> msm_atomic_commit_tail+0x3e4/0x748 > >> commit_tail+0x19c/0x278 > >> drm_atomic_helper_commit+0x1dc/0x1f0 > >> drm_atomic_commit+0xc0/0xd8 > >> drm_atomic_helper_set_config+0xb4/0x134 > >> drm_mode_setcrtc+0x688/0x1248 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > >> --- > >> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > >> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > >> 2 files changed, 13 insertions(+), 16 deletions(-) > >> > >> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c > >> b/drivers/gpu/drm/msm/dp/dp_display.c > >> index 92cd50f..01453db 100644 > >> --- a/drivers/gpu/drm/msm/dp/dp_display.c > >> +++ b/drivers/gpu/drm/msm/dp/dp_display.c > >> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct > >> dp_display_private *dp, u32 data) > >> mutex_unlock(&dp->event_mutex); > >> - /* > >> - * add fail safe mode outside event_mutex scope > >> - * to avoid potiential circular lock with drm thread > >> - */ > >> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > >> - > >> /* uevent will complete connection part */ > >> return 0; > >> }; > >> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c > >> b/drivers/gpu/drm/msm/dp/dp_panel.c > >> index 1aa9aa8c..23fee42 100644 > >> --- a/drivers/gpu/drm/msm/dp/dp_panel.c > >> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > >> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct > >> drm_connector *connector, > >> return rc; > >> } > >> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > >> -{ > >> - /* fail safe edid */ > >> - mutex_lock(&connector->dev->mode_config.mutex); > >> - if (drm_add_modes_noedid(connector, 640, 480)) > >> - drm_set_preferred_mode(connector, 640, 480); > >> - mutex_unlock(&connector->dev->mode_config.mutex); > >> -} > >> - > >> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > >> struct drm_connector *connector) > >> { > >> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel > >> *dp_panel, > >> goto end; > >> } > >> - dp_panel_add_fail_safe_mode(connector); > >> + /* fail safe edid */ > >> + mutex_lock(&connector->dev->mode_config.mutex); > >> + if (drm_add_modes_noedid(connector, 640, 480)) > >> + drm_set_preferred_mode(connector, 640, 480); > >> + mutex_unlock(&connector->dev->mode_config.mutex); > >> } > >> if (panel->aux_cfg_update_done) { > >> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > >> return -EINVAL; > >> } > >> + /* > >> + * add fail safe mode (640x480) here > >> + * since we are executed in drm_thread context, > >> + * no mode_config.mutex acquired required > >> + */ > >> + if (drm_add_modes_noedid(connector, 640, 480)) > >> + drm_set_preferred_mode(connector, 640, 480); > >> + > >> if (dp_panel->edid) > >> return dp_panel_update_modes(connector, dp_panel->edid); > > Also, wouldn't calling get_modes() several times make cause adding more > > and more 640x480 modes to the modes list? > > > > Shouldnt DRM be blocking that here? Call should trickle down here only > if count_modes was 0 > > if (out_resp->count_modes == 0) { > if (is_current_master) > connector->funcs->fill_modes(connector, > dev->mode_config.max_width, > dev->mode_config.max_height); > else > drm_dbg_kms(dev, "User-space requested a forced probe on > [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", > connector->base.id, connector->name); > } > count_modes is set by userspace: /* * This ioctl is called twice, once to determine how much space is * needed, and the 2nd time to fill it. */ So, nothing prevents userspace from passing zero count_mode more than once. However drm_helper_probe_single_connector_modes() will set old modes to MODE_STALE and then will call get_modes(). Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. A more generic question is why do we need to add the mode in two places? -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-23 6:25 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-23 6:25 UTC (permalink / raw) To: Abhinav Kumar Cc: freedreno, quic_sbillaka, airlied, linux-arm-msm, vkoul, dri-devel, swboyd, agross, bjorn.andersson, quic_aravindh, Kuogee Hsieh, sean, linux-kernel On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > > > On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > > On 23/04/2022 02:45, Kuogee Hsieh wrote: > >> Current DP driver implementation has adding safe mode done at > >> dp_hpd_plug_handle() which is expected to be executed under event > >> thread context. > >> > >> However there is possible circular locking happen (see blow stack trace) > >> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > >> is executed under drm_thread context. > >> > >> To break this circular locking, this patch have safe mode added at > >> dp_connector_get_mode() which is executed under drm thread context. > >> Therefore no lock acquired required for &dev->mode_config.mutex while > >> adding fail safe mode since it has been hold by drm thread already. > >> > >> ====================================================== > >> WARNING: possible circular locking dependency detected > >> 5.15.35-lockdep #6 Tainted: G W > >> ------------------------------------------------------ > >> frecon/429 is trying to acquire lock: > >> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > >> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >> > >> but task is already holding lock: > >> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: > >> lock_crtcs+0xb4/0x124 > >> > >> which lock already depends on the new lock. > >> > >> the existing dependency chain (in reverse order) is: > >> > >> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > >> __mutex_lock_common+0x174/0x1a64 > >> mutex_lock_nested+0x98/0xac > >> lock_crtcs+0xb4/0x124 > >> msm_atomic_commit_tail+0x330/0x748 > >> commit_tail+0x19c/0x278 > >> drm_atomic_helper_commit+0x1dc/0x1f0 > >> drm_atomic_commit+0xc0/0xd8 > >> drm_atomic_helper_set_config+0xb4/0x134 > >> drm_mode_setcrtc+0x688/0x1248 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > >> __mutex_lock_common+0x174/0x1a64 > >> ww_mutex_lock+0xb8/0x278 > >> modeset_lock+0x304/0x4ac > >> drm_modeset_lock+0x4c/0x7c > >> drmm_mode_config_init+0x4a8/0xc50 > >> msm_drm_init+0x274/0xac0 > >> msm_drm_bind+0x20/0x2c > >> try_to_bring_up_master+0x3dc/0x470 > >> __component_add+0x18c/0x3c0 > >> component_add+0x1c/0x28 > >> dp_display_probe+0x954/0xa98 > >> platform_probe+0x124/0x15c > >> really_probe+0x1b0/0x5f8 > >> __driver_probe_device+0x174/0x20c > >> driver_probe_device+0x70/0x134 > >> __device_attach_driver+0x130/0x1d0 > >> bus_for_each_drv+0xfc/0x14c > >> __device_attach+0x1bc/0x2bc > >> device_initial_probe+0x1c/0x28 > >> bus_probe_device+0x94/0x178 > >> deferred_probe_work_func+0x1a4/0x1f0 > >> process_one_work+0x5d4/0x9dc > >> worker_thread+0x898/0xccc > >> kthread+0x2d4/0x3d4 > >> ret_from_fork+0x10/0x20 > >> > >> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > >> ww_acquire_init+0x1c4/0x2c8 > >> drm_modeset_acquire_init+0x44/0xc8 > >> drm_helper_probe_single_connector_modes+0xb0/0x12dc > >> drm_mode_getconnector+0x5dc/0xfe8 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > >> __lock_acquire+0x2650/0x672c > >> lock_acquire+0x1b4/0x4ac > >> __mutex_lock_common+0x174/0x1a64 > >> mutex_lock_nested+0x98/0xac > >> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >> dp_hpd_plug_handle+0x1f0/0x280 > >> dp_bridge_enable+0x94/0x2b8 > >> drm_atomic_bridge_chain_enable+0x11c/0x168 > >> drm_atomic_helper_commit_modeset_enables+0x500/0x740 > >> msm_atomic_commit_tail+0x3e4/0x748 > >> commit_tail+0x19c/0x278 > >> drm_atomic_helper_commit+0x1dc/0x1f0 > >> drm_atomic_commit+0xc0/0xd8 > >> drm_atomic_helper_set_config+0xb4/0x134 > >> drm_mode_setcrtc+0x688/0x1248 > >> drm_ioctl_kernel+0x1e4/0x338 > >> drm_ioctl+0x3a4/0x684 > >> __arm64_sys_ioctl+0x118/0x154 > >> invoke_syscall+0x78/0x224 > >> el0_svc_common+0x178/0x200 > >> do_el0_svc+0x94/0x13c > >> el0_svc+0x5c/0xec > >> el0t_64_sync_handler+0x78/0x108 > >> el0t_64_sync+0x1a4/0x1a8 > >> > >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > >> --- > >> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > >> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > >> 2 files changed, 13 insertions(+), 16 deletions(-) > >> > >> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c > >> b/drivers/gpu/drm/msm/dp/dp_display.c > >> index 92cd50f..01453db 100644 > >> --- a/drivers/gpu/drm/msm/dp/dp_display.c > >> +++ b/drivers/gpu/drm/msm/dp/dp_display.c > >> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct > >> dp_display_private *dp, u32 data) > >> mutex_unlock(&dp->event_mutex); > >> - /* > >> - * add fail safe mode outside event_mutex scope > >> - * to avoid potiential circular lock with drm thread > >> - */ > >> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > >> - > >> /* uevent will complete connection part */ > >> return 0; > >> }; > >> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c > >> b/drivers/gpu/drm/msm/dp/dp_panel.c > >> index 1aa9aa8c..23fee42 100644 > >> --- a/drivers/gpu/drm/msm/dp/dp_panel.c > >> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > >> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct > >> drm_connector *connector, > >> return rc; > >> } > >> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > >> -{ > >> - /* fail safe edid */ > >> - mutex_lock(&connector->dev->mode_config.mutex); > >> - if (drm_add_modes_noedid(connector, 640, 480)) > >> - drm_set_preferred_mode(connector, 640, 480); > >> - mutex_unlock(&connector->dev->mode_config.mutex); > >> -} > >> - > >> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > >> struct drm_connector *connector) > >> { > >> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel > >> *dp_panel, > >> goto end; > >> } > >> - dp_panel_add_fail_safe_mode(connector); > >> + /* fail safe edid */ > >> + mutex_lock(&connector->dev->mode_config.mutex); > >> + if (drm_add_modes_noedid(connector, 640, 480)) > >> + drm_set_preferred_mode(connector, 640, 480); > >> + mutex_unlock(&connector->dev->mode_config.mutex); > >> } > >> if (panel->aux_cfg_update_done) { > >> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > >> return -EINVAL; > >> } > >> + /* > >> + * add fail safe mode (640x480) here > >> + * since we are executed in drm_thread context, > >> + * no mode_config.mutex acquired required > >> + */ > >> + if (drm_add_modes_noedid(connector, 640, 480)) > >> + drm_set_preferred_mode(connector, 640, 480); > >> + > >> if (dp_panel->edid) > >> return dp_panel_update_modes(connector, dp_panel->edid); > > Also, wouldn't calling get_modes() several times make cause adding more > > and more 640x480 modes to the modes list? > > > > Shouldnt DRM be blocking that here? Call should trickle down here only > if count_modes was 0 > > if (out_resp->count_modes == 0) { > if (is_current_master) > connector->funcs->fill_modes(connector, > dev->mode_config.max_width, > dev->mode_config.max_height); > else > drm_dbg_kms(dev, "User-space requested a forced probe on > [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", > connector->base.id, connector->name); > } > count_modes is set by userspace: /* * This ioctl is called twice, once to determine how much space is * needed, and the 2nd time to fill it. */ So, nothing prevents userspace from passing zero count_mode more than once. However drm_helper_probe_single_connector_modes() will set old modes to MODE_STALE and then will call get_modes(). Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. A more generic question is why do we need to add the mode in two places? -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-23 6:25 ` Dmitry Baryshkov @ 2022-04-23 15:33 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-23 15:33 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson, quic_sbillaka, linux-arm-msm, dri-devel, linux-kernel, quic_aravindh, freedreno On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: > On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> >> >> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>> Current DP driver implementation has adding safe mode done at >>>> dp_hpd_plug_handle() which is expected to be executed under event >>>> thread context. >>>> >>>> However there is possible circular locking happen (see blow stack trace) >>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >>>> is executed under drm_thread context. >>>> >>>> To break this circular locking, this patch have safe mode added at >>>> dp_connector_get_mode() which is executed under drm thread context. >>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>> adding fail safe mode since it has been hold by drm thread already. >>>> >>>> ====================================================== >>>> WARNING: possible circular locking dependency detected >>>> 5.15.35-lockdep #6 Tainted: G W >>>> ------------------------------------------------------ >>>> frecon/429 is trying to acquire lock: >>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>> >>>> but task is already holding lock: >>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>> lock_crtcs+0xb4/0x124 >>>> >>>> which lock already depends on the new lock. >>>> >>>> the existing dependency chain (in reverse order) is: >>>> >>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>> __mutex_lock_common+0x174/0x1a64 >>>> mutex_lock_nested+0x98/0xac >>>> lock_crtcs+0xb4/0x124 >>>> msm_atomic_commit_tail+0x330/0x748 >>>> commit_tail+0x19c/0x278 >>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>> drm_atomic_commit+0xc0/0xd8 >>>> drm_atomic_helper_set_config+0xb4/0x134 >>>> drm_mode_setcrtc+0x688/0x1248 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>> __mutex_lock_common+0x174/0x1a64 >>>> ww_mutex_lock+0xb8/0x278 >>>> modeset_lock+0x304/0x4ac >>>> drm_modeset_lock+0x4c/0x7c >>>> drmm_mode_config_init+0x4a8/0xc50 >>>> msm_drm_init+0x274/0xac0 >>>> msm_drm_bind+0x20/0x2c >>>> try_to_bring_up_master+0x3dc/0x470 >>>> __component_add+0x18c/0x3c0 >>>> component_add+0x1c/0x28 >>>> dp_display_probe+0x954/0xa98 >>>> platform_probe+0x124/0x15c >>>> really_probe+0x1b0/0x5f8 >>>> __driver_probe_device+0x174/0x20c >>>> driver_probe_device+0x70/0x134 >>>> __device_attach_driver+0x130/0x1d0 >>>> bus_for_each_drv+0xfc/0x14c >>>> __device_attach+0x1bc/0x2bc >>>> device_initial_probe+0x1c/0x28 >>>> bus_probe_device+0x94/0x178 >>>> deferred_probe_work_func+0x1a4/0x1f0 >>>> process_one_work+0x5d4/0x9dc >>>> worker_thread+0x898/0xccc >>>> kthread+0x2d4/0x3d4 >>>> ret_from_fork+0x10/0x20 >>>> >>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>> ww_acquire_init+0x1c4/0x2c8 >>>> drm_modeset_acquire_init+0x44/0xc8 >>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>> drm_mode_getconnector+0x5dc/0xfe8 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>> __lock_acquire+0x2650/0x672c >>>> lock_acquire+0x1b4/0x4ac >>>> __mutex_lock_common+0x174/0x1a64 >>>> mutex_lock_nested+0x98/0xac >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>> dp_hpd_plug_handle+0x1f0/0x280 >>>> dp_bridge_enable+0x94/0x2b8 >>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>> msm_atomic_commit_tail+0x3e4/0x748 >>>> commit_tail+0x19c/0x278 >>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>> drm_atomic_commit+0xc0/0xd8 >>>> drm_atomic_helper_set_config+0xb4/0x134 >>>> drm_mode_setcrtc+0x688/0x1248 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>> --- >>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>> >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>> index 92cd50f..01453db 100644 >>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>> dp_display_private *dp, u32 data) >>>> mutex_unlock(&dp->event_mutex); >>>> - /* >>>> - * add fail safe mode outside event_mutex scope >>>> - * to avoid potiential circular lock with drm thread >>>> - */ >>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>> - >>>> /* uevent will complete connection part */ >>>> return 0; >>>> }; >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>> index 1aa9aa8c..23fee42 100644 >>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>> drm_connector *connector, >>>> return rc; >>>> } >>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>> -{ >>>> - /* fail safe edid */ >>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>> - drm_set_preferred_mode(connector, 640, 480); >>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>> -} >>>> - >>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>> struct drm_connector *connector) >>>> { >>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>> *dp_panel, >>>> goto end; >>>> } >>>> - dp_panel_add_fail_safe_mode(connector); >>>> + /* fail safe edid */ >>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>> + drm_set_preferred_mode(connector, 640, 480); >>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>> } >>>> if (panel->aux_cfg_update_done) { >>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>> return -EINVAL; >>>> } >>>> + /* >>>> + * add fail safe mode (640x480) here >>>> + * since we are executed in drm_thread context, >>>> + * no mode_config.mutex acquired required >>>> + */ >>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>> + drm_set_preferred_mode(connector, 640, 480); >>>> + >>>> if (dp_panel->edid) >>>> return dp_panel_update_modes(connector, dp_panel->edid); >>> Also, wouldn't calling get_modes() several times make cause adding more >>> and more 640x480 modes to the modes list? >>> >> >> Shouldnt DRM be blocking that here? Call should trickle down here only >> if count_modes was 0 >> >> if (out_resp->count_modes == 0) { >> if (is_current_master) >> connector->funcs->fill_modes(connector, >> dev->mode_config.max_width, >> dev->mode_config.max_height); >> else >> drm_dbg_kms(dev, "User-space requested a forced probe on >> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", >> connector->base.id, connector->name); >> } >> > > count_modes is set by userspace: > /* > * This ioctl is called twice, once to determine how much space is > * needed, and the 2nd time to fill it. > */ > > So, nothing prevents userspace from passing zero count_mode more than once. Ack, some non-optimized usermodes can do this. > > However drm_helper_probe_single_connector_modes() will set old modes > to MODE_STALE and then will call get_modes(). > Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. > Got it. > A more generic question is why do we need to add the mode in two places? > Answering behalf of kuogee but the two places are for different purposes: 1) When there is no EDID read if (!dp_panel->edid) { That case we should add the fail-safe mode as otherwise display will be blank for cases where there was nothing wrong with the monitor as such but the EDID read from aux failed for some reason. Even DRM does this but just not 640x480 here: 518 if (count == 0 && (connector->status == connector_status_connected || 519 connector->status == connector_status_unknown)) 520 count = drm_add_modes_noedid(connector, 1024, 768); 2) When there was a valid EDID but no 640x480 mode This is the equipment specific case and the one even I was a bit surprised. There is a DP compliance equipment we have in-house and while validation, it was found that in its list of modes , it did not have any modes which chromebook supported ( due to 2 lanes ). But my understanding was that, all sinks should have atleast 640x480 but apparently this one did not have that. So to handle this DP compliance equipment behavior, we had to do this. Thanks Abhinav ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-23 15:33 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-23 15:33 UTC (permalink / raw) To: Dmitry Baryshkov Cc: freedreno, quic_sbillaka, airlied, linux-arm-msm, vkoul, dri-devel, swboyd, agross, bjorn.andersson, quic_aravindh, Kuogee Hsieh, sean, linux-kernel On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: > On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> >> >> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>> Current DP driver implementation has adding safe mode done at >>>> dp_hpd_plug_handle() which is expected to be executed under event >>>> thread context. >>>> >>>> However there is possible circular locking happen (see blow stack trace) >>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >>>> is executed under drm_thread context. >>>> >>>> To break this circular locking, this patch have safe mode added at >>>> dp_connector_get_mode() which is executed under drm thread context. >>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>> adding fail safe mode since it has been hold by drm thread already. >>>> >>>> ====================================================== >>>> WARNING: possible circular locking dependency detected >>>> 5.15.35-lockdep #6 Tainted: G W >>>> ------------------------------------------------------ >>>> frecon/429 is trying to acquire lock: >>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>> >>>> but task is already holding lock: >>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>> lock_crtcs+0xb4/0x124 >>>> >>>> which lock already depends on the new lock. >>>> >>>> the existing dependency chain (in reverse order) is: >>>> >>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>> __mutex_lock_common+0x174/0x1a64 >>>> mutex_lock_nested+0x98/0xac >>>> lock_crtcs+0xb4/0x124 >>>> msm_atomic_commit_tail+0x330/0x748 >>>> commit_tail+0x19c/0x278 >>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>> drm_atomic_commit+0xc0/0xd8 >>>> drm_atomic_helper_set_config+0xb4/0x134 >>>> drm_mode_setcrtc+0x688/0x1248 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>> __mutex_lock_common+0x174/0x1a64 >>>> ww_mutex_lock+0xb8/0x278 >>>> modeset_lock+0x304/0x4ac >>>> drm_modeset_lock+0x4c/0x7c >>>> drmm_mode_config_init+0x4a8/0xc50 >>>> msm_drm_init+0x274/0xac0 >>>> msm_drm_bind+0x20/0x2c >>>> try_to_bring_up_master+0x3dc/0x470 >>>> __component_add+0x18c/0x3c0 >>>> component_add+0x1c/0x28 >>>> dp_display_probe+0x954/0xa98 >>>> platform_probe+0x124/0x15c >>>> really_probe+0x1b0/0x5f8 >>>> __driver_probe_device+0x174/0x20c >>>> driver_probe_device+0x70/0x134 >>>> __device_attach_driver+0x130/0x1d0 >>>> bus_for_each_drv+0xfc/0x14c >>>> __device_attach+0x1bc/0x2bc >>>> device_initial_probe+0x1c/0x28 >>>> bus_probe_device+0x94/0x178 >>>> deferred_probe_work_func+0x1a4/0x1f0 >>>> process_one_work+0x5d4/0x9dc >>>> worker_thread+0x898/0xccc >>>> kthread+0x2d4/0x3d4 >>>> ret_from_fork+0x10/0x20 >>>> >>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>> ww_acquire_init+0x1c4/0x2c8 >>>> drm_modeset_acquire_init+0x44/0xc8 >>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>> drm_mode_getconnector+0x5dc/0xfe8 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>> __lock_acquire+0x2650/0x672c >>>> lock_acquire+0x1b4/0x4ac >>>> __mutex_lock_common+0x174/0x1a64 >>>> mutex_lock_nested+0x98/0xac >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>> dp_hpd_plug_handle+0x1f0/0x280 >>>> dp_bridge_enable+0x94/0x2b8 >>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>> msm_atomic_commit_tail+0x3e4/0x748 >>>> commit_tail+0x19c/0x278 >>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>> drm_atomic_commit+0xc0/0xd8 >>>> drm_atomic_helper_set_config+0xb4/0x134 >>>> drm_mode_setcrtc+0x688/0x1248 >>>> drm_ioctl_kernel+0x1e4/0x338 >>>> drm_ioctl+0x3a4/0x684 >>>> __arm64_sys_ioctl+0x118/0x154 >>>> invoke_syscall+0x78/0x224 >>>> el0_svc_common+0x178/0x200 >>>> do_el0_svc+0x94/0x13c >>>> el0_svc+0x5c/0xec >>>> el0t_64_sync_handler+0x78/0x108 >>>> el0t_64_sync+0x1a4/0x1a8 >>>> >>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>> --- >>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>> >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>> index 92cd50f..01453db 100644 >>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>> dp_display_private *dp, u32 data) >>>> mutex_unlock(&dp->event_mutex); >>>> - /* >>>> - * add fail safe mode outside event_mutex scope >>>> - * to avoid potiential circular lock with drm thread >>>> - */ >>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>> - >>>> /* uevent will complete connection part */ >>>> return 0; >>>> }; >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>> index 1aa9aa8c..23fee42 100644 >>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>> drm_connector *connector, >>>> return rc; >>>> } >>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>> -{ >>>> - /* fail safe edid */ >>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>> - drm_set_preferred_mode(connector, 640, 480); >>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>> -} >>>> - >>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>> struct drm_connector *connector) >>>> { >>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>> *dp_panel, >>>> goto end; >>>> } >>>> - dp_panel_add_fail_safe_mode(connector); >>>> + /* fail safe edid */ >>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>> + drm_set_preferred_mode(connector, 640, 480); >>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>> } >>>> if (panel->aux_cfg_update_done) { >>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>> return -EINVAL; >>>> } >>>> + /* >>>> + * add fail safe mode (640x480) here >>>> + * since we are executed in drm_thread context, >>>> + * no mode_config.mutex acquired required >>>> + */ >>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>> + drm_set_preferred_mode(connector, 640, 480); >>>> + >>>> if (dp_panel->edid) >>>> return dp_panel_update_modes(connector, dp_panel->edid); >>> Also, wouldn't calling get_modes() several times make cause adding more >>> and more 640x480 modes to the modes list? >>> >> >> Shouldnt DRM be blocking that here? Call should trickle down here only >> if count_modes was 0 >> >> if (out_resp->count_modes == 0) { >> if (is_current_master) >> connector->funcs->fill_modes(connector, >> dev->mode_config.max_width, >> dev->mode_config.max_height); >> else >> drm_dbg_kms(dev, "User-space requested a forced probe on >> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", >> connector->base.id, connector->name); >> } >> > > count_modes is set by userspace: > /* > * This ioctl is called twice, once to determine how much space is > * needed, and the 2nd time to fill it. > */ > > So, nothing prevents userspace from passing zero count_mode more than once. Ack, some non-optimized usermodes can do this. > > However drm_helper_probe_single_connector_modes() will set old modes > to MODE_STALE and then will call get_modes(). > Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. > Got it. > A more generic question is why do we need to add the mode in two places? > Answering behalf of kuogee but the two places are for different purposes: 1) When there is no EDID read if (!dp_panel->edid) { That case we should add the fail-safe mode as otherwise display will be blank for cases where there was nothing wrong with the monitor as such but the EDID read from aux failed for some reason. Even DRM does this but just not 640x480 here: 518 if (count == 0 && (connector->status == connector_status_connected || 519 connector->status == connector_status_unknown)) 520 count = drm_add_modes_noedid(connector, 1024, 768); 2) When there was a valid EDID but no 640x480 mode This is the equipment specific case and the one even I was a bit surprised. There is a DP compliance equipment we have in-house and while validation, it was found that in its list of modes , it did not have any modes which chromebook supported ( due to 2 lanes ). But my understanding was that, all sinks should have atleast 640x480 but apparently this one did not have that. So to handle this DP compliance equipment behavior, we had to do this. Thanks Abhinav ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-23 15:33 ` Abhinav Kumar @ 2022-04-25 23:14 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-25 23:14 UTC (permalink / raw) To: Abhinav Kumar Cc: Kuogee Hsieh, robdclark, sean, swboyd, vkoul, daniel, airlied, agross, bjorn.andersson, quic_sbillaka, linux-arm-msm, dri-devel, linux-kernel, quic_aravindh, freedreno On 23/04/2022 18:33, Abhinav Kumar wrote: > > > On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: >> On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar >> <quic_abhinavk@quicinc.com> wrote: >>> >>> >>> >>> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>>> Current DP driver implementation has adding safe mode done at >>>>> dp_hpd_plug_handle() which is expected to be executed under event >>>>> thread context. >>>>> >>>>> However there is possible circular locking happen (see blow stack >>>>> trace) >>>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() >>>>> which >>>>> is executed under drm_thread context. >>>>> >>>>> To break this circular locking, this patch have safe mode added at >>>>> dp_connector_get_mode() which is executed under drm thread context. >>>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>>> adding fail safe mode since it has been hold by drm thread already. >>>>> >>>>> ====================================================== >>>>> WARNING: possible circular locking dependency detected >>>>> 5.15.35-lockdep #6 Tainted: G W >>>>> ------------------------------------------------------ >>>>> frecon/429 is trying to acquire lock: >>>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>> >>>>> but task is already holding lock: >>>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>>> lock_crtcs+0xb4/0x124 >>>>> >>>>> which lock already depends on the new lock. >>>>> >>>>> the existing dependency chain (in reverse order) is: >>>>> >>>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> mutex_lock_nested+0x98/0xac >>>>> lock_crtcs+0xb4/0x124 >>>>> msm_atomic_commit_tail+0x330/0x748 >>>>> commit_tail+0x19c/0x278 >>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>> drm_atomic_commit+0xc0/0xd8 >>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>> drm_mode_setcrtc+0x688/0x1248 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> ww_mutex_lock+0xb8/0x278 >>>>> modeset_lock+0x304/0x4ac >>>>> drm_modeset_lock+0x4c/0x7c >>>>> drmm_mode_config_init+0x4a8/0xc50 >>>>> msm_drm_init+0x274/0xac0 >>>>> msm_drm_bind+0x20/0x2c >>>>> try_to_bring_up_master+0x3dc/0x470 >>>>> __component_add+0x18c/0x3c0 >>>>> component_add+0x1c/0x28 >>>>> dp_display_probe+0x954/0xa98 >>>>> platform_probe+0x124/0x15c >>>>> really_probe+0x1b0/0x5f8 >>>>> __driver_probe_device+0x174/0x20c >>>>> driver_probe_device+0x70/0x134 >>>>> __device_attach_driver+0x130/0x1d0 >>>>> bus_for_each_drv+0xfc/0x14c >>>>> __device_attach+0x1bc/0x2bc >>>>> device_initial_probe+0x1c/0x28 >>>>> bus_probe_device+0x94/0x178 >>>>> deferred_probe_work_func+0x1a4/0x1f0 >>>>> process_one_work+0x5d4/0x9dc >>>>> worker_thread+0x898/0xccc >>>>> kthread+0x2d4/0x3d4 >>>>> ret_from_fork+0x10/0x20 >>>>> >>>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>>> ww_acquire_init+0x1c4/0x2c8 >>>>> drm_modeset_acquire_init+0x44/0xc8 >>>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>>> drm_mode_getconnector+0x5dc/0xfe8 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>>> __lock_acquire+0x2650/0x672c >>>>> lock_acquire+0x1b4/0x4ac >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> mutex_lock_nested+0x98/0xac >>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>> dp_hpd_plug_handle+0x1f0/0x280 >>>>> dp_bridge_enable+0x94/0x2b8 >>>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>>> msm_atomic_commit_tail+0x3e4/0x748 >>>>> commit_tail+0x19c/0x278 >>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>> drm_atomic_commit+0xc0/0xd8 >>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>> drm_mode_setcrtc+0x688/0x1248 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>>> --- >>>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>>> >>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>>> index 92cd50f..01453db 100644 >>>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>>> dp_display_private *dp, u32 data) >>>>> mutex_unlock(&dp->event_mutex); >>>>> - /* >>>>> - * add fail safe mode outside event_mutex scope >>>>> - * to avoid potiential circular lock with drm thread >>>>> - */ >>>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>>> - >>>>> /* uevent will complete connection part */ >>>>> return 0; >>>>> }; >>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> index 1aa9aa8c..23fee42 100644 >>>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>>> drm_connector *connector, >>>>> return rc; >>>>> } >>>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>>> -{ >>>>> - /* fail safe edid */ >>>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>>> - drm_set_preferred_mode(connector, 640, 480); >>>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>>> -} >>>>> - >>>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>>> struct drm_connector *connector) >>>>> { >>>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>>> *dp_panel, >>>>> goto end; >>>>> } >>>>> - dp_panel_add_fail_safe_mode(connector); >>>>> + /* fail safe edid */ >>>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>>> } >>>>> if (panel->aux_cfg_update_done) { >>>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>>> return -EINVAL; >>>>> } >>>>> + /* >>>>> + * add fail safe mode (640x480) here >>>>> + * since we are executed in drm_thread context, >>>>> + * no mode_config.mutex acquired required >>>>> + */ >>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>> + >>>>> if (dp_panel->edid) >>>>> return dp_panel_update_modes(connector, dp_panel->edid); >>>> Also, wouldn't calling get_modes() several times make cause adding more >>>> and more 640x480 modes to the modes list? >>>> >>> >>> Shouldnt DRM be blocking that here? Call should trickle down here only >>> if count_modes was 0 >>> >>> if (out_resp->count_modes == 0) { >>> if (is_current_master) >>> connector->funcs->fill_modes(connector, >>> dev->mode_config.max_width, >>> dev->mode_config.max_height); >>> else >>> drm_dbg_kms(dev, "User-space requested a forced probe on >>> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only >>> probe", >>> connector->base.id, connector->name); >>> } >>> >> >> count_modes is set by userspace: >> /* >> * This ioctl is called twice, once to determine how much >> space is >> * needed, and the 2nd time to fill it. >> */ >> >> So, nothing prevents userspace from passing zero count_mode more than >> once. > Ack, some non-optimized usermodes can do this. >> >> However drm_helper_probe_single_connector_modes() will set old modes >> to MODE_STALE and then will call get_modes(). >> Then drm_mode_prune_invalid() will prune stale modes. So, this should >> be fine. >> > Got it. >> A more generic question is why do we need to add the mode in two places? >> > Answering behalf of kuogee but the two places are for different purposes: > > 1) When there is no EDID read > > if (!dp_panel->edid) { > > That case we should add the fail-safe mode as otherwise display will be > blank for cases where there was nothing wrong with the monitor as such > but the EDID read from aux failed for some reason. Even DRM does this > but just not 640x480 here: > > 518 if (count == 0 && (connector->status == > connector_status_connected || > 519 connector->status == connector_status_unknown)) > 520 count = drm_add_modes_noedid(connector, 1024, 768); Yes, but this happens when there are no other modes. While if I'm not mistaken our code adds 640x480 even if there are modes. > 2) When there was a valid EDID but no 640x480 mode > > This is the equipment specific case and the one even I was a bit > surprised. There is a DP compliance equipment we have in-house and while > validation, it was found that in its list of modes , it did not have any > modes which chromebook supported ( due to 2 lanes ). But my > understanding was that, all sinks should have atleast 640x480 but > apparently this one did not have that. So to handle this DP compliance > equipment behavior, we had to do this. I see. Not the perfect solution, but looks like a necessity. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-25 23:14 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-25 23:14 UTC (permalink / raw) To: Abhinav Kumar Cc: freedreno, quic_sbillaka, airlied, linux-arm-msm, vkoul, dri-devel, swboyd, agross, bjorn.andersson, quic_aravindh, Kuogee Hsieh, sean, linux-kernel On 23/04/2022 18:33, Abhinav Kumar wrote: > > > On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: >> On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar >> <quic_abhinavk@quicinc.com> wrote: >>> >>> >>> >>> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>>> Current DP driver implementation has adding safe mode done at >>>>> dp_hpd_plug_handle() which is expected to be executed under event >>>>> thread context. >>>>> >>>>> However there is possible circular locking happen (see blow stack >>>>> trace) >>>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() >>>>> which >>>>> is executed under drm_thread context. >>>>> >>>>> To break this circular locking, this patch have safe mode added at >>>>> dp_connector_get_mode() which is executed under drm thread context. >>>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>>> adding fail safe mode since it has been hold by drm thread already. >>>>> >>>>> ====================================================== >>>>> WARNING: possible circular locking dependency detected >>>>> 5.15.35-lockdep #6 Tainted: G W >>>>> ------------------------------------------------------ >>>>> frecon/429 is trying to acquire lock: >>>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>> >>>>> but task is already holding lock: >>>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>>> lock_crtcs+0xb4/0x124 >>>>> >>>>> which lock already depends on the new lock. >>>>> >>>>> the existing dependency chain (in reverse order) is: >>>>> >>>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> mutex_lock_nested+0x98/0xac >>>>> lock_crtcs+0xb4/0x124 >>>>> msm_atomic_commit_tail+0x330/0x748 >>>>> commit_tail+0x19c/0x278 >>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>> drm_atomic_commit+0xc0/0xd8 >>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>> drm_mode_setcrtc+0x688/0x1248 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> ww_mutex_lock+0xb8/0x278 >>>>> modeset_lock+0x304/0x4ac >>>>> drm_modeset_lock+0x4c/0x7c >>>>> drmm_mode_config_init+0x4a8/0xc50 >>>>> msm_drm_init+0x274/0xac0 >>>>> msm_drm_bind+0x20/0x2c >>>>> try_to_bring_up_master+0x3dc/0x470 >>>>> __component_add+0x18c/0x3c0 >>>>> component_add+0x1c/0x28 >>>>> dp_display_probe+0x954/0xa98 >>>>> platform_probe+0x124/0x15c >>>>> really_probe+0x1b0/0x5f8 >>>>> __driver_probe_device+0x174/0x20c >>>>> driver_probe_device+0x70/0x134 >>>>> __device_attach_driver+0x130/0x1d0 >>>>> bus_for_each_drv+0xfc/0x14c >>>>> __device_attach+0x1bc/0x2bc >>>>> device_initial_probe+0x1c/0x28 >>>>> bus_probe_device+0x94/0x178 >>>>> deferred_probe_work_func+0x1a4/0x1f0 >>>>> process_one_work+0x5d4/0x9dc >>>>> worker_thread+0x898/0xccc >>>>> kthread+0x2d4/0x3d4 >>>>> ret_from_fork+0x10/0x20 >>>>> >>>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>>> ww_acquire_init+0x1c4/0x2c8 >>>>> drm_modeset_acquire_init+0x44/0xc8 >>>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>>> drm_mode_getconnector+0x5dc/0xfe8 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>>> __lock_acquire+0x2650/0x672c >>>>> lock_acquire+0x1b4/0x4ac >>>>> __mutex_lock_common+0x174/0x1a64 >>>>> mutex_lock_nested+0x98/0xac >>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>> dp_hpd_plug_handle+0x1f0/0x280 >>>>> dp_bridge_enable+0x94/0x2b8 >>>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>>> msm_atomic_commit_tail+0x3e4/0x748 >>>>> commit_tail+0x19c/0x278 >>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>> drm_atomic_commit+0xc0/0xd8 >>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>> drm_mode_setcrtc+0x688/0x1248 >>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>> drm_ioctl+0x3a4/0x684 >>>>> __arm64_sys_ioctl+0x118/0x154 >>>>> invoke_syscall+0x78/0x224 >>>>> el0_svc_common+0x178/0x200 >>>>> do_el0_svc+0x94/0x13c >>>>> el0_svc+0x5c/0xec >>>>> el0t_64_sync_handler+0x78/0x108 >>>>> el0t_64_sync+0x1a4/0x1a8 >>>>> >>>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>>> --- >>>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>>> >>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>>> index 92cd50f..01453db 100644 >>>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>>> dp_display_private *dp, u32 data) >>>>> mutex_unlock(&dp->event_mutex); >>>>> - /* >>>>> - * add fail safe mode outside event_mutex scope >>>>> - * to avoid potiential circular lock with drm thread >>>>> - */ >>>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>>> - >>>>> /* uevent will complete connection part */ >>>>> return 0; >>>>> }; >>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> index 1aa9aa8c..23fee42 100644 >>>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>>> drm_connector *connector, >>>>> return rc; >>>>> } >>>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>>> -{ >>>>> - /* fail safe edid */ >>>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>>> - drm_set_preferred_mode(connector, 640, 480); >>>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>>> -} >>>>> - >>>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>>> struct drm_connector *connector) >>>>> { >>>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>>> *dp_panel, >>>>> goto end; >>>>> } >>>>> - dp_panel_add_fail_safe_mode(connector); >>>>> + /* fail safe edid */ >>>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>>> } >>>>> if (panel->aux_cfg_update_done) { >>>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>>> return -EINVAL; >>>>> } >>>>> + /* >>>>> + * add fail safe mode (640x480) here >>>>> + * since we are executed in drm_thread context, >>>>> + * no mode_config.mutex acquired required >>>>> + */ >>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>> + >>>>> if (dp_panel->edid) >>>>> return dp_panel_update_modes(connector, dp_panel->edid); >>>> Also, wouldn't calling get_modes() several times make cause adding more >>>> and more 640x480 modes to the modes list? >>>> >>> >>> Shouldnt DRM be blocking that here? Call should trickle down here only >>> if count_modes was 0 >>> >>> if (out_resp->count_modes == 0) { >>> if (is_current_master) >>> connector->funcs->fill_modes(connector, >>> dev->mode_config.max_width, >>> dev->mode_config.max_height); >>> else >>> drm_dbg_kms(dev, "User-space requested a forced probe on >>> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only >>> probe", >>> connector->base.id, connector->name); >>> } >>> >> >> count_modes is set by userspace: >> /* >> * This ioctl is called twice, once to determine how much >> space is >> * needed, and the 2nd time to fill it. >> */ >> >> So, nothing prevents userspace from passing zero count_mode more than >> once. > Ack, some non-optimized usermodes can do this. >> >> However drm_helper_probe_single_connector_modes() will set old modes >> to MODE_STALE and then will call get_modes(). >> Then drm_mode_prune_invalid() will prune stale modes. So, this should >> be fine. >> > Got it. >> A more generic question is why do we need to add the mode in two places? >> > Answering behalf of kuogee but the two places are for different purposes: > > 1) When there is no EDID read > > if (!dp_panel->edid) { > > That case we should add the fail-safe mode as otherwise display will be > blank for cases where there was nothing wrong with the monitor as such > but the EDID read from aux failed for some reason. Even DRM does this > but just not 640x480 here: > > 518 if (count == 0 && (connector->status == > connector_status_connected || > 519 connector->status == connector_status_unknown)) > 520 count = drm_add_modes_noedid(connector, 1024, 768); Yes, but this happens when there are no other modes. While if I'm not mistaken our code adds 640x480 even if there are modes. > 2) When there was a valid EDID but no 640x480 mode > > This is the equipment specific case and the one even I was a bit > surprised. There is a DP compliance equipment we have in-house and while > validation, it was found that in its list of modes , it did not have any > modes which chromebook supported ( due to 2 lanes ). But my > understanding was that, all sinks should have atleast 640x480 but > apparently this one did not have that. So to handle this DP compliance > equipment behavior, we had to do this. I see. Not the perfect solution, but looks like a necessity. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-23 15:33 ` Abhinav Kumar @ 2022-04-26 0:26 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 0:26 UTC (permalink / raw) To: Abhinav Kumar Cc: Dmitry Baryshkov, freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, Vinod Koul, dri-devel, Stephen Boyd, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, Sean Paul, LKML Hi, On Sat, Apr 23, 2022 at 8:34 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: > > On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > >> > >> > >> > >> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > >>> On 23/04/2022 02:45, Kuogee Hsieh wrote: > >>>> Current DP driver implementation has adding safe mode done at > >>>> dp_hpd_plug_handle() which is expected to be executed under event > >>>> thread context. > >>>> > >>>> However there is possible circular locking happen (see blow stack trace) > >>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > >>>> is executed under drm_thread context. > >>>> > >>>> To break this circular locking, this patch have safe mode added at > >>>> dp_connector_get_mode() which is executed under drm thread context. > >>>> Therefore no lock acquired required for &dev->mode_config.mutex while > >>>> adding fail safe mode since it has been hold by drm thread already. > >>>> > >>>> ====================================================== > >>>> WARNING: possible circular locking dependency detected > >>>> 5.15.35-lockdep #6 Tainted: G W > >>>> ------------------------------------------------------ > >>>> frecon/429 is trying to acquire lock: > >>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >>>> > >>>> but task is already holding lock: > >>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: > >>>> lock_crtcs+0xb4/0x124 > >>>> > >>>> which lock already depends on the new lock. > >>>> > >>>> the existing dependency chain (in reverse order) is: > >>>> > >>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> mutex_lock_nested+0x98/0xac > >>>> lock_crtcs+0xb4/0x124 > >>>> msm_atomic_commit_tail+0x330/0x748 > >>>> commit_tail+0x19c/0x278 > >>>> drm_atomic_helper_commit+0x1dc/0x1f0 > >>>> drm_atomic_commit+0xc0/0xd8 > >>>> drm_atomic_helper_set_config+0xb4/0x134 > >>>> drm_mode_setcrtc+0x688/0x1248 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> ww_mutex_lock+0xb8/0x278 > >>>> modeset_lock+0x304/0x4ac > >>>> drm_modeset_lock+0x4c/0x7c > >>>> drmm_mode_config_init+0x4a8/0xc50 > >>>> msm_drm_init+0x274/0xac0 > >>>> msm_drm_bind+0x20/0x2c > >>>> try_to_bring_up_master+0x3dc/0x470 > >>>> __component_add+0x18c/0x3c0 > >>>> component_add+0x1c/0x28 > >>>> dp_display_probe+0x954/0xa98 > >>>> platform_probe+0x124/0x15c > >>>> really_probe+0x1b0/0x5f8 > >>>> __driver_probe_device+0x174/0x20c > >>>> driver_probe_device+0x70/0x134 > >>>> __device_attach_driver+0x130/0x1d0 > >>>> bus_for_each_drv+0xfc/0x14c > >>>> __device_attach+0x1bc/0x2bc > >>>> device_initial_probe+0x1c/0x28 > >>>> bus_probe_device+0x94/0x178 > >>>> deferred_probe_work_func+0x1a4/0x1f0 > >>>> process_one_work+0x5d4/0x9dc > >>>> worker_thread+0x898/0xccc > >>>> kthread+0x2d4/0x3d4 > >>>> ret_from_fork+0x10/0x20 > >>>> > >>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > >>>> ww_acquire_init+0x1c4/0x2c8 > >>>> drm_modeset_acquire_init+0x44/0xc8 > >>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc > >>>> drm_mode_getconnector+0x5dc/0xfe8 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > >>>> __lock_acquire+0x2650/0x672c > >>>> lock_acquire+0x1b4/0x4ac > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> mutex_lock_nested+0x98/0xac > >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >>>> dp_hpd_plug_handle+0x1f0/0x280 > >>>> dp_bridge_enable+0x94/0x2b8 > >>>> drm_atomic_bridge_chain_enable+0x11c/0x168 > >>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 > >>>> msm_atomic_commit_tail+0x3e4/0x748 > >>>> commit_tail+0x19c/0x278 > >>>> drm_atomic_helper_commit+0x1dc/0x1f0 > >>>> drm_atomic_commit+0xc0/0xd8 > >>>> drm_atomic_helper_set_config+0xb4/0x134 > >>>> drm_mode_setcrtc+0x688/0x1248 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > >>>> --- > >>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > >>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > >>>> 2 files changed, 13 insertions(+), 16 deletions(-) > >>>> > >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c > >>>> b/drivers/gpu/drm/msm/dp/dp_display.c > >>>> index 92cd50f..01453db 100644 > >>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c > >>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c > >>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct > >>>> dp_display_private *dp, u32 data) > >>>> mutex_unlock(&dp->event_mutex); > >>>> - /* > >>>> - * add fail safe mode outside event_mutex scope > >>>> - * to avoid potiential circular lock with drm thread > >>>> - */ > >>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > >>>> - > >>>> /* uevent will complete connection part */ > >>>> return 0; > >>>> }; > >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> b/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> index 1aa9aa8c..23fee42 100644 > >>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct > >>>> drm_connector *connector, > >>>> return rc; > >>>> } > >>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > >>>> -{ > >>>> - /* fail safe edid */ > >>>> - mutex_lock(&connector->dev->mode_config.mutex); > >>>> - if (drm_add_modes_noedid(connector, 640, 480)) > >>>> - drm_set_preferred_mode(connector, 640, 480); > >>>> - mutex_unlock(&connector->dev->mode_config.mutex); > >>>> -} > >>>> - > >>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > >>>> struct drm_connector *connector) > >>>> { > >>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel > >>>> *dp_panel, > >>>> goto end; > >>>> } > >>>> - dp_panel_add_fail_safe_mode(connector); > >>>> + /* fail safe edid */ > >>>> + mutex_lock(&connector->dev->mode_config.mutex); > >>>> + if (drm_add_modes_noedid(connector, 640, 480)) > >>>> + drm_set_preferred_mode(connector, 640, 480); > >>>> + mutex_unlock(&connector->dev->mode_config.mutex); > >>>> } > >>>> if (panel->aux_cfg_update_done) { > >>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > >>>> return -EINVAL; > >>>> } > >>>> + /* > >>>> + * add fail safe mode (640x480) here > >>>> + * since we are executed in drm_thread context, > >>>> + * no mode_config.mutex acquired required > >>>> + */ > >>>> + if (drm_add_modes_noedid(connector, 640, 480)) > >>>> + drm_set_preferred_mode(connector, 640, 480); > >>>> + > >>>> if (dp_panel->edid) > >>>> return dp_panel_update_modes(connector, dp_panel->edid); > >>> Also, wouldn't calling get_modes() several times make cause adding more > >>> and more 640x480 modes to the modes list? > >>> > >> > >> Shouldnt DRM be blocking that here? Call should trickle down here only > >> if count_modes was 0 > >> > >> if (out_resp->count_modes == 0) { > >> if (is_current_master) > >> connector->funcs->fill_modes(connector, > >> dev->mode_config.max_width, > >> dev->mode_config.max_height); > >> else > >> drm_dbg_kms(dev, "User-space requested a forced probe on > >> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", > >> connector->base.id, connector->name); > >> } > >> > > > > count_modes is set by userspace: > > /* > > * This ioctl is called twice, once to determine how much space is > > * needed, and the 2nd time to fill it. > > */ > > > > So, nothing prevents userspace from passing zero count_mode more than once. > Ack, some non-optimized usermodes can do this. > > > > However drm_helper_probe_single_connector_modes() will set old modes > > to MODE_STALE and then will call get_modes(). > > Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. > > > Got it. > > A more generic question is why do we need to add the mode in two places? > > > Answering behalf of kuogee but the two places are for different purposes: > > 1) When there is no EDID read > > if (!dp_panel->edid) { > > That case we should add the fail-safe mode as otherwise display will be > blank for cases where there was nothing wrong with the monitor as such > but the EDID read from aux failed for some reason. Even DRM does this > but just not 640x480 here: > > 518 if (count == 0 && (connector->status == connector_status_connected || > 519 connector->status == connector_status_unknown)) > 520 count = drm_add_modes_noedid(connector, 1024, 768); But drm_add_modes_noedid() _will_ add the 640x480 modes, won't it? It will add all "failsafe" modes that are less than or equal to 1024x768 and 60Hz or less. See the table "drm_dmt_modes". I don't understand why the DRM core's call doesn't solve the problem for you in the first place? > 2) When there was a valid EDID but no 640x480 mode > > This is the equipment specific case and the one even I was a bit > surprised. There is a DP compliance equipment we have in-house and while > validation, it was found that in its list of modes , it did not have any > modes which chromebook supported ( due to 2 lanes ). But my > understanding was that, all sinks should have atleast 640x480 but > apparently this one did not have that. So to handle this DP compliance > equipment behavior, we had to do this. That doesn't seem right. If there's a valid EDID and the valid EDID doesn't contain 640x480, are you _sure_ you're supposed to be adding 640x480? That doesn't sound right to me. I've got a tiny display in front of me for testing that only has one mode: #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 It wouldn't be correct to add a 640x480 mode to this panel... ...and, in fact, after applying ${SUBJECT} patch I see that DRM (incorrectly) thinks that my display supports 640x480. I see: #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 #1 640x480 59.94 640 656 752 800 480 490 492 525 25175 So IMO we _shouldn't_ land ${SUBJECT} patch. Just for testing, I also tried a hack to make EDID reading fail (return -EIO in the MSM dp_aux_transfer() function if msg->request < 8). Before ${SUBJECT} patch I'd see these modes: #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 ...and after ${SUBJECT} patch I'd see: #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 ...so your patch causes 640x480 to be prioritized. That also doesn't seem ideal. If it was ideal, the DRM core should have listed 640x480 first. I'll repeat my refrain that I'm not a DRM expert, but if I were doing things, I'd rather revert commit 8b2c181e3dcf ("drm/msm/dp: add fail safe mode outside of event_mutex context") and commit d4aca422539c ("drm/msm/dp: always add fail-safe mode into connector mode list") and then go back and look more carefully about what the problem was in the first place. Why didn't the failsafe modes added by the DRM core solve the problem for you in the first place? -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 0:26 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 0:26 UTC (permalink / raw) To: Abhinav Kumar Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi, On Sat, Apr 23, 2022 at 8:34 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: > > On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > >> > >> > >> > >> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: > >>> On 23/04/2022 02:45, Kuogee Hsieh wrote: > >>>> Current DP driver implementation has adding safe mode done at > >>>> dp_hpd_plug_handle() which is expected to be executed under event > >>>> thread context. > >>>> > >>>> However there is possible circular locking happen (see blow stack trace) > >>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which > >>>> is executed under drm_thread context. > >>>> > >>>> To break this circular locking, this patch have safe mode added at > >>>> dp_connector_get_mode() which is executed under drm thread context. > >>>> Therefore no lock acquired required for &dev->mode_config.mutex while > >>>> adding fail safe mode since it has been hold by drm thread already. > >>>> > >>>> ====================================================== > >>>> WARNING: possible circular locking dependency detected > >>>> 5.15.35-lockdep #6 Tainted: G W > >>>> ------------------------------------------------------ > >>>> frecon/429 is trying to acquire lock: > >>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: > >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >>>> > >>>> but task is already holding lock: > >>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: > >>>> lock_crtcs+0xb4/0x124 > >>>> > >>>> which lock already depends on the new lock. > >>>> > >>>> the existing dependency chain (in reverse order) is: > >>>> > >>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> mutex_lock_nested+0x98/0xac > >>>> lock_crtcs+0xb4/0x124 > >>>> msm_atomic_commit_tail+0x330/0x748 > >>>> commit_tail+0x19c/0x278 > >>>> drm_atomic_helper_commit+0x1dc/0x1f0 > >>>> drm_atomic_commit+0xc0/0xd8 > >>>> drm_atomic_helper_set_config+0xb4/0x134 > >>>> drm_mode_setcrtc+0x688/0x1248 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> ww_mutex_lock+0xb8/0x278 > >>>> modeset_lock+0x304/0x4ac > >>>> drm_modeset_lock+0x4c/0x7c > >>>> drmm_mode_config_init+0x4a8/0xc50 > >>>> msm_drm_init+0x274/0xac0 > >>>> msm_drm_bind+0x20/0x2c > >>>> try_to_bring_up_master+0x3dc/0x470 > >>>> __component_add+0x18c/0x3c0 > >>>> component_add+0x1c/0x28 > >>>> dp_display_probe+0x954/0xa98 > >>>> platform_probe+0x124/0x15c > >>>> really_probe+0x1b0/0x5f8 > >>>> __driver_probe_device+0x174/0x20c > >>>> driver_probe_device+0x70/0x134 > >>>> __device_attach_driver+0x130/0x1d0 > >>>> bus_for_each_drv+0xfc/0x14c > >>>> __device_attach+0x1bc/0x2bc > >>>> device_initial_probe+0x1c/0x28 > >>>> bus_probe_device+0x94/0x178 > >>>> deferred_probe_work_func+0x1a4/0x1f0 > >>>> process_one_work+0x5d4/0x9dc > >>>> worker_thread+0x898/0xccc > >>>> kthread+0x2d4/0x3d4 > >>>> ret_from_fork+0x10/0x20 > >>>> > >>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: > >>>> ww_acquire_init+0x1c4/0x2c8 > >>>> drm_modeset_acquire_init+0x44/0xc8 > >>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc > >>>> drm_mode_getconnector+0x5dc/0xfe8 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: > >>>> __lock_acquire+0x2650/0x672c > >>>> lock_acquire+0x1b4/0x4ac > >>>> __mutex_lock_common+0x174/0x1a64 > >>>> mutex_lock_nested+0x98/0xac > >>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 > >>>> dp_hpd_plug_handle+0x1f0/0x280 > >>>> dp_bridge_enable+0x94/0x2b8 > >>>> drm_atomic_bridge_chain_enable+0x11c/0x168 > >>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 > >>>> msm_atomic_commit_tail+0x3e4/0x748 > >>>> commit_tail+0x19c/0x278 > >>>> drm_atomic_helper_commit+0x1dc/0x1f0 > >>>> drm_atomic_commit+0xc0/0xd8 > >>>> drm_atomic_helper_set_config+0xb4/0x134 > >>>> drm_mode_setcrtc+0x688/0x1248 > >>>> drm_ioctl_kernel+0x1e4/0x338 > >>>> drm_ioctl+0x3a4/0x684 > >>>> __arm64_sys_ioctl+0x118/0x154 > >>>> invoke_syscall+0x78/0x224 > >>>> el0_svc_common+0x178/0x200 > >>>> do_el0_svc+0x94/0x13c > >>>> el0_svc+0x5c/0xec > >>>> el0t_64_sync_handler+0x78/0x108 > >>>> el0t_64_sync+0x1a4/0x1a8 > >>>> > >>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > >>>> --- > >>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ > >>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- > >>>> 2 files changed, 13 insertions(+), 16 deletions(-) > >>>> > >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c > >>>> b/drivers/gpu/drm/msm/dp/dp_display.c > >>>> index 92cd50f..01453db 100644 > >>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c > >>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c > >>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct > >>>> dp_display_private *dp, u32 data) > >>>> mutex_unlock(&dp->event_mutex); > >>>> - /* > >>>> - * add fail safe mode outside event_mutex scope > >>>> - * to avoid potiential circular lock with drm thread > >>>> - */ > >>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); > >>>> - > >>>> /* uevent will complete connection part */ > >>>> return 0; > >>>> }; > >>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> b/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> index 1aa9aa8c..23fee42 100644 > >>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c > >>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct > >>>> drm_connector *connector, > >>>> return rc; > >>>> } > >>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) > >>>> -{ > >>>> - /* fail safe edid */ > >>>> - mutex_lock(&connector->dev->mode_config.mutex); > >>>> - if (drm_add_modes_noedid(connector, 640, 480)) > >>>> - drm_set_preferred_mode(connector, 640, 480); > >>>> - mutex_unlock(&connector->dev->mode_config.mutex); > >>>> -} > >>>> - > >>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, > >>>> struct drm_connector *connector) > >>>> { > >>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel > >>>> *dp_panel, > >>>> goto end; > >>>> } > >>>> - dp_panel_add_fail_safe_mode(connector); > >>>> + /* fail safe edid */ > >>>> + mutex_lock(&connector->dev->mode_config.mutex); > >>>> + if (drm_add_modes_noedid(connector, 640, 480)) > >>>> + drm_set_preferred_mode(connector, 640, 480); > >>>> + mutex_unlock(&connector->dev->mode_config.mutex); > >>>> } > >>>> if (panel->aux_cfg_update_done) { > >>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, > >>>> return -EINVAL; > >>>> } > >>>> + /* > >>>> + * add fail safe mode (640x480) here > >>>> + * since we are executed in drm_thread context, > >>>> + * no mode_config.mutex acquired required > >>>> + */ > >>>> + if (drm_add_modes_noedid(connector, 640, 480)) > >>>> + drm_set_preferred_mode(connector, 640, 480); > >>>> + > >>>> if (dp_panel->edid) > >>>> return dp_panel_update_modes(connector, dp_panel->edid); > >>> Also, wouldn't calling get_modes() several times make cause adding more > >>> and more 640x480 modes to the modes list? > >>> > >> > >> Shouldnt DRM be blocking that here? Call should trickle down here only > >> if count_modes was 0 > >> > >> if (out_resp->count_modes == 0) { > >> if (is_current_master) > >> connector->funcs->fill_modes(connector, > >> dev->mode_config.max_width, > >> dev->mode_config.max_height); > >> else > >> drm_dbg_kms(dev, "User-space requested a forced probe on > >> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", > >> connector->base.id, connector->name); > >> } > >> > > > > count_modes is set by userspace: > > /* > > * This ioctl is called twice, once to determine how much space is > > * needed, and the 2nd time to fill it. > > */ > > > > So, nothing prevents userspace from passing zero count_mode more than once. > Ack, some non-optimized usermodes can do this. > > > > However drm_helper_probe_single_connector_modes() will set old modes > > to MODE_STALE and then will call get_modes(). > > Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. > > > Got it. > > A more generic question is why do we need to add the mode in two places? > > > Answering behalf of kuogee but the two places are for different purposes: > > 1) When there is no EDID read > > if (!dp_panel->edid) { > > That case we should add the fail-safe mode as otherwise display will be > blank for cases where there was nothing wrong with the monitor as such > but the EDID read from aux failed for some reason. Even DRM does this > but just not 640x480 here: > > 518 if (count == 0 && (connector->status == connector_status_connected || > 519 connector->status == connector_status_unknown)) > 520 count = drm_add_modes_noedid(connector, 1024, 768); But drm_add_modes_noedid() _will_ add the 640x480 modes, won't it? It will add all "failsafe" modes that are less than or equal to 1024x768 and 60Hz or less. See the table "drm_dmt_modes". I don't understand why the DRM core's call doesn't solve the problem for you in the first place? > 2) When there was a valid EDID but no 640x480 mode > > This is the equipment specific case and the one even I was a bit > surprised. There is a DP compliance equipment we have in-house and while > validation, it was found that in its list of modes , it did not have any > modes which chromebook supported ( due to 2 lanes ). But my > understanding was that, all sinks should have atleast 640x480 but > apparently this one did not have that. So to handle this DP compliance > equipment behavior, we had to do this. That doesn't seem right. If there's a valid EDID and the valid EDID doesn't contain 640x480, are you _sure_ you're supposed to be adding 640x480? That doesn't sound right to me. I've got a tiny display in front of me for testing that only has one mode: #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 It wouldn't be correct to add a 640x480 mode to this panel... ...and, in fact, after applying ${SUBJECT} patch I see that DRM (incorrectly) thinks that my display supports 640x480. I see: #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 #1 640x480 59.94 640 656 752 800 480 490 492 525 25175 So IMO we _shouldn't_ land ${SUBJECT} patch. Just for testing, I also tried a hack to make EDID reading fail (return -EIO in the MSM dp_aux_transfer() function if msg->request < 8). Before ${SUBJECT} patch I'd see these modes: #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 ...and after ${SUBJECT} patch I'd see: #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 ...so your patch causes 640x480 to be prioritized. That also doesn't seem ideal. If it was ideal, the DRM core should have listed 640x480 first. I'll repeat my refrain that I'm not a DRM expert, but if I were doing things, I'd rather revert commit 8b2c181e3dcf ("drm/msm/dp: add fail safe mode outside of event_mutex context") and commit d4aca422539c ("drm/msm/dp: always add fail-safe mode into connector mode list") and then go back and look more carefully about what the problem was in the first place. Why didn't the failsafe modes added by the DRM core solve the problem for you in the first place? -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 0:26 ` Doug Anderson @ 2022-04-26 1:42 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 1:42 UTC (permalink / raw) To: Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi Doug On 4/25/2022 5:26 PM, Doug Anderson wrote: > Hi, > > On Sat, Apr 23, 2022 at 8:34 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: >>> On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >>>> >>>> >>>> >>>> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>>>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>>>> Current DP driver implementation has adding safe mode done at >>>>>> dp_hpd_plug_handle() which is expected to be executed under event >>>>>> thread context. >>>>>> >>>>>> However there is possible circular locking happen (see blow stack trace) >>>>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >>>>>> is executed under drm_thread context. >>>>>> >>>>>> To break this circular locking, this patch have safe mode added at >>>>>> dp_connector_get_mode() which is executed under drm thread context. >>>>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>>>> adding fail safe mode since it has been hold by drm thread already. >>>>>> >>>>>> ====================================================== >>>>>> WARNING: possible circular locking dependency detected >>>>>> 5.15.35-lockdep #6 Tainted: G W >>>>>> ------------------------------------------------------ >>>>>> frecon/429 is trying to acquire lock: >>>>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>>> >>>>>> but task is already holding lock: >>>>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>>>> lock_crtcs+0xb4/0x124 >>>>>> >>>>>> which lock already depends on the new lock. >>>>>> >>>>>> the existing dependency chain (in reverse order) is: >>>>>> >>>>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> mutex_lock_nested+0x98/0xac >>>>>> lock_crtcs+0xb4/0x124 >>>>>> msm_atomic_commit_tail+0x330/0x748 >>>>>> commit_tail+0x19c/0x278 >>>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>>> drm_atomic_commit+0xc0/0xd8 >>>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>>> drm_mode_setcrtc+0x688/0x1248 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> ww_mutex_lock+0xb8/0x278 >>>>>> modeset_lock+0x304/0x4ac >>>>>> drm_modeset_lock+0x4c/0x7c >>>>>> drmm_mode_config_init+0x4a8/0xc50 >>>>>> msm_drm_init+0x274/0xac0 >>>>>> msm_drm_bind+0x20/0x2c >>>>>> try_to_bring_up_master+0x3dc/0x470 >>>>>> __component_add+0x18c/0x3c0 >>>>>> component_add+0x1c/0x28 >>>>>> dp_display_probe+0x954/0xa98 >>>>>> platform_probe+0x124/0x15c >>>>>> really_probe+0x1b0/0x5f8 >>>>>> __driver_probe_device+0x174/0x20c >>>>>> driver_probe_device+0x70/0x134 >>>>>> __device_attach_driver+0x130/0x1d0 >>>>>> bus_for_each_drv+0xfc/0x14c >>>>>> __device_attach+0x1bc/0x2bc >>>>>> device_initial_probe+0x1c/0x28 >>>>>> bus_probe_device+0x94/0x178 >>>>>> deferred_probe_work_func+0x1a4/0x1f0 >>>>>> process_one_work+0x5d4/0x9dc >>>>>> worker_thread+0x898/0xccc >>>>>> kthread+0x2d4/0x3d4 >>>>>> ret_from_fork+0x10/0x20 >>>>>> >>>>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>>>> ww_acquire_init+0x1c4/0x2c8 >>>>>> drm_modeset_acquire_init+0x44/0xc8 >>>>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>>>> drm_mode_getconnector+0x5dc/0xfe8 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>>>> __lock_acquire+0x2650/0x672c >>>>>> lock_acquire+0x1b4/0x4ac >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> mutex_lock_nested+0x98/0xac >>>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>>> dp_hpd_plug_handle+0x1f0/0x280 >>>>>> dp_bridge_enable+0x94/0x2b8 >>>>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>>>> msm_atomic_commit_tail+0x3e4/0x748 >>>>>> commit_tail+0x19c/0x278 >>>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>>> drm_atomic_commit+0xc0/0xd8 >>>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>>> drm_mode_setcrtc+0x688/0x1248 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>>>> --- >>>>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>>>> >>>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> index 92cd50f..01453db 100644 >>>>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>>>> dp_display_private *dp, u32 data) >>>>>> mutex_unlock(&dp->event_mutex); >>>>>> - /* >>>>>> - * add fail safe mode outside event_mutex scope >>>>>> - * to avoid potiential circular lock with drm thread >>>>>> - */ >>>>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>>>> - >>>>>> /* uevent will complete connection part */ >>>>>> return 0; >>>>>> }; >>>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> index 1aa9aa8c..23fee42 100644 >>>>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>>>> drm_connector *connector, >>>>>> return rc; >>>>>> } >>>>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>>>> -{ >>>>>> - /* fail safe edid */ >>>>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> - drm_set_preferred_mode(connector, 640, 480); >>>>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>>>> -} >>>>>> - >>>>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>>>> struct drm_connector *connector) >>>>>> { >>>>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>>>> *dp_panel, >>>>>> goto end; >>>>>> } >>>>>> - dp_panel_add_fail_safe_mode(connector); >>>>>> + /* fail safe edid */ >>>>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>>>> } >>>>>> if (panel->aux_cfg_update_done) { >>>>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>>>> return -EINVAL; >>>>>> } >>>>>> + /* >>>>>> + * add fail safe mode (640x480) here >>>>>> + * since we are executed in drm_thread context, >>>>>> + * no mode_config.mutex acquired required >>>>>> + */ >>>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>>> + >>>>>> if (dp_panel->edid) >>>>>> return dp_panel_update_modes(connector, dp_panel->edid); >>>>> Also, wouldn't calling get_modes() several times make cause adding more >>>>> and more 640x480 modes to the modes list? >>>>> >>>> >>>> Shouldnt DRM be blocking that here? Call should trickle down here only >>>> if count_modes was 0 >>>> >>>> if (out_resp->count_modes == 0) { >>>> if (is_current_master) >>>> connector->funcs->fill_modes(connector, >>>> dev->mode_config.max_width, >>>> dev->mode_config.max_height); >>>> else >>>> drm_dbg_kms(dev, "User-space requested a forced probe on >>>> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", >>>> connector->base.id, connector->name); >>>> } >>>> >>> >>> count_modes is set by userspace: >>> /* >>> * This ioctl is called twice, once to determine how much space is >>> * needed, and the 2nd time to fill it. >>> */ >>> >>> So, nothing prevents userspace from passing zero count_mode more than once. >> Ack, some non-optimized usermodes can do this. >>> >>> However drm_helper_probe_single_connector_modes() will set old modes >>> to MODE_STALE and then will call get_modes(). >>> Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. >>> >> Got it. >>> A more generic question is why do we need to add the mode in two places? >>> >> Answering behalf of kuogee but the two places are for different purposes: >> >> 1) When there is no EDID read >> >> if (!dp_panel->edid) { >> >> That case we should add the fail-safe mode as otherwise display will be >> blank for cases where there was nothing wrong with the monitor as such >> but the EDID read from aux failed for some reason. Even DRM does this >> but just not 640x480 here: >> >> 518 if (count == 0 && (connector->status == connector_status_connected || >> 519 connector->status == connector_status_unknown)) >> 520 count = drm_add_modes_noedid(connector, 1024, 768); > > But drm_add_modes_noedid() _will_ add the 640x480 modes, won't it? It > will add all "failsafe" modes that are less than or equal to 1024x768 > and 60Hz or less. See the table "drm_dmt_modes". I don't understand > why the DRM core's call doesn't solve the problem for you in the first > place? This is a good point that drm_add_modes_noedid() will add all modes <=1024x768. Perhaps we can drop the call for the case where there was no EDID and let DRM fwk handle that. But that wont fix this problem, will explain in (2). > > >> 2) When there was a valid EDID but no 640x480 mode >> >> This is the equipment specific case and the one even I was a bit >> surprised. There is a DP compliance equipment we have in-house and while >> validation, it was found that in its list of modes , it did not have any >> modes which chromebook supported ( due to 2 lanes ). But my >> understanding was that, all sinks should have atleast 640x480 but >> apparently this one did not have that. So to handle this DP compliance >> equipment behavior, we had to do this. > > That doesn't seem right. If there's a valid EDID and the valid EDID > doesn't contain 640x480, are you _sure_ you're supposed to be adding > 640x480? That doesn't sound right to me. I've got a tiny display in > front of me for testing that only has one mode: > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > As I had wrote, DRM core kicks in only when the count of modes is 0. Here what is happening is the count was not 0 but 640x480 was not present in the EDID. So we had to add it explicitly. Your tiny display is a display port display? I am referring to only display port monitors. If your tiny display is DP, it should have had 640x480 in its list of modes. > It wouldn't be correct to add a 640x480 mode to this panel... ...and, > in fact, after applying ${SUBJECT} patch I see that DRM (incorrectly) > thinks that my display supports 640x480. I see: > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > #1 640x480 59.94 640 656 752 800 480 490 492 525 25175 > Its not incorrect if its display port as it should have had it. The equipment we had did not have it which was incorrect. So typically for DP monitors this change should cause no change as 640x480 mode should already be present. > So IMO we _shouldn't_ land ${SUBJECT} patch. > > Just for testing, I also tried a hack to make EDID reading fail > (return -EIO in the MSM dp_aux_transfer() function if msg->request < > 8). Before ${SUBJECT} patch I'd see these modes: > > #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > ...and after ${SUBJECT} patch I'd see: > > #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 > #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > ...so your patch causes 640x480 to be prioritized. That also doesn't > seem ideal. If it was ideal, the DRM core should have listed 640x480 > first. So this is a different display or these modes are coming due to the drm_add_modes_noedid() call because of the EDID read fail right? If its coming due to the drm_add_modes_noedid() call and then we are adding the 640x480 mode on top of that, like I mentioned in my previous comment, we can remove the call for the !edid case to address this. > > I'll repeat my refrain that I'm not a DRM expert, but if I were doing > things, I'd rather revert commit 8b2c181e3dcf ("drm/msm/dp: add fail > safe mode outside of event_mutex context") and commit d4aca422539c > ("drm/msm/dp: always add fail-safe mode into connector mode list") and > then go back and look more carefully about what the problem was in the > first place. Why didn't the failsafe modes added by the DRM core solve > the problem for you in the first place? I have explained why DRM core did not solve this problem. Thats because it will hit only when count of modes is 0, here count of modes is not 0. So we know the root-cause. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 1:42 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 1:42 UTC (permalink / raw) To: Doug Anderson Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi Doug On 4/25/2022 5:26 PM, Doug Anderson wrote: > Hi, > > On Sat, Apr 23, 2022 at 8:34 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> On 4/22/2022 11:25 PM, Dmitry Baryshkov wrote: >>> On Sat, 23 Apr 2022 at 03:12, Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >>>> >>>> >>>> >>>> On 4/22/2022 5:07 PM, Dmitry Baryshkov wrote: >>>>> On 23/04/2022 02:45, Kuogee Hsieh wrote: >>>>>> Current DP driver implementation has adding safe mode done at >>>>>> dp_hpd_plug_handle() which is expected to be executed under event >>>>>> thread context. >>>>>> >>>>>> However there is possible circular locking happen (see blow stack trace) >>>>>> after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which >>>>>> is executed under drm_thread context. >>>>>> >>>>>> To break this circular locking, this patch have safe mode added at >>>>>> dp_connector_get_mode() which is executed under drm thread context. >>>>>> Therefore no lock acquired required for &dev->mode_config.mutex while >>>>>> adding fail safe mode since it has been hold by drm thread already. >>>>>> >>>>>> ====================================================== >>>>>> WARNING: possible circular locking dependency detected >>>>>> 5.15.35-lockdep #6 Tainted: G W >>>>>> ------------------------------------------------------ >>>>>> frecon/429 is trying to acquire lock: >>>>>> ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at: >>>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>>> >>>>>> but task is already holding lock: >>>>>> ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: >>>>>> lock_crtcs+0xb4/0x124 >>>>>> >>>>>> which lock already depends on the new lock. >>>>>> >>>>>> the existing dependency chain (in reverse order) is: >>>>>> >>>>>> -> #3 (&kms->commit_lock[i]){+.+.}-{3:3}: >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> mutex_lock_nested+0x98/0xac >>>>>> lock_crtcs+0xb4/0x124 >>>>>> msm_atomic_commit_tail+0x330/0x748 >>>>>> commit_tail+0x19c/0x278 >>>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>>> drm_atomic_commit+0xc0/0xd8 >>>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>>> drm_mode_setcrtc+0x688/0x1248 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> -> #2 (crtc_ww_class_mutex){+.+.}-{3:3}: >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> ww_mutex_lock+0xb8/0x278 >>>>>> modeset_lock+0x304/0x4ac >>>>>> drm_modeset_lock+0x4c/0x7c >>>>>> drmm_mode_config_init+0x4a8/0xc50 >>>>>> msm_drm_init+0x274/0xac0 >>>>>> msm_drm_bind+0x20/0x2c >>>>>> try_to_bring_up_master+0x3dc/0x470 >>>>>> __component_add+0x18c/0x3c0 >>>>>> component_add+0x1c/0x28 >>>>>> dp_display_probe+0x954/0xa98 >>>>>> platform_probe+0x124/0x15c >>>>>> really_probe+0x1b0/0x5f8 >>>>>> __driver_probe_device+0x174/0x20c >>>>>> driver_probe_device+0x70/0x134 >>>>>> __device_attach_driver+0x130/0x1d0 >>>>>> bus_for_each_drv+0xfc/0x14c >>>>>> __device_attach+0x1bc/0x2bc >>>>>> device_initial_probe+0x1c/0x28 >>>>>> bus_probe_device+0x94/0x178 >>>>>> deferred_probe_work_func+0x1a4/0x1f0 >>>>>> process_one_work+0x5d4/0x9dc >>>>>> worker_thread+0x898/0xccc >>>>>> kthread+0x2d4/0x3d4 >>>>>> ret_from_fork+0x10/0x20 >>>>>> >>>>>> -> #1 (crtc_ww_class_acquire){+.+.}-{0:0}: >>>>>> ww_acquire_init+0x1c4/0x2c8 >>>>>> drm_modeset_acquire_init+0x44/0xc8 >>>>>> drm_helper_probe_single_connector_modes+0xb0/0x12dc >>>>>> drm_mode_getconnector+0x5dc/0xfe8 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> -> #0 (&dev->mode_config.mutex){+.+.}-{3:3}: >>>>>> __lock_acquire+0x2650/0x672c >>>>>> lock_acquire+0x1b4/0x4ac >>>>>> __mutex_lock_common+0x174/0x1a64 >>>>>> mutex_lock_nested+0x98/0xac >>>>>> dp_panel_add_fail_safe_mode+0x4c/0xa0 >>>>>> dp_hpd_plug_handle+0x1f0/0x280 >>>>>> dp_bridge_enable+0x94/0x2b8 >>>>>> drm_atomic_bridge_chain_enable+0x11c/0x168 >>>>>> drm_atomic_helper_commit_modeset_enables+0x500/0x740 >>>>>> msm_atomic_commit_tail+0x3e4/0x748 >>>>>> commit_tail+0x19c/0x278 >>>>>> drm_atomic_helper_commit+0x1dc/0x1f0 >>>>>> drm_atomic_commit+0xc0/0xd8 >>>>>> drm_atomic_helper_set_config+0xb4/0x134 >>>>>> drm_mode_setcrtc+0x688/0x1248 >>>>>> drm_ioctl_kernel+0x1e4/0x338 >>>>>> drm_ioctl+0x3a4/0x684 >>>>>> __arm64_sys_ioctl+0x118/0x154 >>>>>> invoke_syscall+0x78/0x224 >>>>>> el0_svc_common+0x178/0x200 >>>>>> do_el0_svc+0x94/0x13c >>>>>> el0_svc+0x5c/0xec >>>>>> el0t_64_sync_handler+0x78/0x108 >>>>>> el0t_64_sync+0x1a4/0x1a8 >>>>>> >>>>>> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >>>>>> --- >>>>>> drivers/gpu/drm/msm/dp/dp_display.c | 6 ------ >>>>>> drivers/gpu/drm/msm/dp/dp_panel.c | 23 +++++++++++++---------- >>>>>> 2 files changed, 13 insertions(+), 16 deletions(-) >>>>>> >>>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> b/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> index 92cd50f..01453db 100644 >>>>>> --- a/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> +++ b/drivers/gpu/drm/msm/dp/dp_display.c >>>>>> @@ -555,12 +555,6 @@ static int dp_hpd_plug_handle(struct >>>>>> dp_display_private *dp, u32 data) >>>>>> mutex_unlock(&dp->event_mutex); >>>>>> - /* >>>>>> - * add fail safe mode outside event_mutex scope >>>>>> - * to avoid potiential circular lock with drm thread >>>>>> - */ >>>>>> - dp_panel_add_fail_safe_mode(dp->dp_display.connector); >>>>>> - >>>>>> /* uevent will complete connection part */ >>>>>> return 0; >>>>>> }; >>>>>> diff --git a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> index 1aa9aa8c..23fee42 100644 >>>>>> --- a/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> +++ b/drivers/gpu/drm/msm/dp/dp_panel.c >>>>>> @@ -151,15 +151,6 @@ static int dp_panel_update_modes(struct >>>>>> drm_connector *connector, >>>>>> return rc; >>>>>> } >>>>>> -void dp_panel_add_fail_safe_mode(struct drm_connector *connector) >>>>>> -{ >>>>>> - /* fail safe edid */ >>>>>> - mutex_lock(&connector->dev->mode_config.mutex); >>>>>> - if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> - drm_set_preferred_mode(connector, 640, 480); >>>>>> - mutex_unlock(&connector->dev->mode_config.mutex); >>>>>> -} >>>>>> - >>>>>> int dp_panel_read_sink_caps(struct dp_panel *dp_panel, >>>>>> struct drm_connector *connector) >>>>>> { >>>>>> @@ -216,7 +207,11 @@ int dp_panel_read_sink_caps(struct dp_panel >>>>>> *dp_panel, >>>>>> goto end; >>>>>> } >>>>>> - dp_panel_add_fail_safe_mode(connector); >>>>>> + /* fail safe edid */ >>>>>> + mutex_lock(&connector->dev->mode_config.mutex); >>>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>>> + mutex_unlock(&connector->dev->mode_config.mutex); >>>>>> } >>>>>> if (panel->aux_cfg_update_done) { >>>>>> @@ -266,6 +261,14 @@ int dp_panel_get_modes(struct dp_panel *dp_panel, >>>>>> return -EINVAL; >>>>>> } >>>>>> + /* >>>>>> + * add fail safe mode (640x480) here >>>>>> + * since we are executed in drm_thread context, >>>>>> + * no mode_config.mutex acquired required >>>>>> + */ >>>>>> + if (drm_add_modes_noedid(connector, 640, 480)) >>>>>> + drm_set_preferred_mode(connector, 640, 480); >>>>>> + >>>>>> if (dp_panel->edid) >>>>>> return dp_panel_update_modes(connector, dp_panel->edid); >>>>> Also, wouldn't calling get_modes() several times make cause adding more >>>>> and more 640x480 modes to the modes list? >>>>> >>>> >>>> Shouldnt DRM be blocking that here? Call should trickle down here only >>>> if count_modes was 0 >>>> >>>> if (out_resp->count_modes == 0) { >>>> if (is_current_master) >>>> connector->funcs->fill_modes(connector, >>>> dev->mode_config.max_width, >>>> dev->mode_config.max_height); >>>> else >>>> drm_dbg_kms(dev, "User-space requested a forced probe on >>>> [CONNECTOR:%d:%s] but is not the DRM master, demoting to read-only probe", >>>> connector->base.id, connector->name); >>>> } >>>> >>> >>> count_modes is set by userspace: >>> /* >>> * This ioctl is called twice, once to determine how much space is >>> * needed, and the 2nd time to fill it. >>> */ >>> >>> So, nothing prevents userspace from passing zero count_mode more than once. >> Ack, some non-optimized usermodes can do this. >>> >>> However drm_helper_probe_single_connector_modes() will set old modes >>> to MODE_STALE and then will call get_modes(). >>> Then drm_mode_prune_invalid() will prune stale modes. So, this should be fine. >>> >> Got it. >>> A more generic question is why do we need to add the mode in two places? >>> >> Answering behalf of kuogee but the two places are for different purposes: >> >> 1) When there is no EDID read >> >> if (!dp_panel->edid) { >> >> That case we should add the fail-safe mode as otherwise display will be >> blank for cases where there was nothing wrong with the monitor as such >> but the EDID read from aux failed for some reason. Even DRM does this >> but just not 640x480 here: >> >> 518 if (count == 0 && (connector->status == connector_status_connected || >> 519 connector->status == connector_status_unknown)) >> 520 count = drm_add_modes_noedid(connector, 1024, 768); > > But drm_add_modes_noedid() _will_ add the 640x480 modes, won't it? It > will add all "failsafe" modes that are less than or equal to 1024x768 > and 60Hz or less. See the table "drm_dmt_modes". I don't understand > why the DRM core's call doesn't solve the problem for you in the first > place? This is a good point that drm_add_modes_noedid() will add all modes <=1024x768. Perhaps we can drop the call for the case where there was no EDID and let DRM fwk handle that. But that wont fix this problem, will explain in (2). > > >> 2) When there was a valid EDID but no 640x480 mode >> >> This is the equipment specific case and the one even I was a bit >> surprised. There is a DP compliance equipment we have in-house and while >> validation, it was found that in its list of modes , it did not have any >> modes which chromebook supported ( due to 2 lanes ). But my >> understanding was that, all sinks should have atleast 640x480 but >> apparently this one did not have that. So to handle this DP compliance >> equipment behavior, we had to do this. > > That doesn't seem right. If there's a valid EDID and the valid EDID > doesn't contain 640x480, are you _sure_ you're supposed to be adding > 640x480? That doesn't sound right to me. I've got a tiny display in > front of me for testing that only has one mode: > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > As I had wrote, DRM core kicks in only when the count of modes is 0. Here what is happening is the count was not 0 but 640x480 was not present in the EDID. So we had to add it explicitly. Your tiny display is a display port display? I am referring to only display port monitors. If your tiny display is DP, it should have had 640x480 in its list of modes. > It wouldn't be correct to add a 640x480 mode to this panel... ...and, > in fact, after applying ${SUBJECT} patch I see that DRM (incorrectly) > thinks that my display supports 640x480. I see: > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > #1 640x480 59.94 640 656 752 800 480 490 492 525 25175 > Its not incorrect if its display port as it should have had it. The equipment we had did not have it which was incorrect. So typically for DP monitors this change should cause no change as 640x480 mode should already be present. > So IMO we _shouldn't_ land ${SUBJECT} patch. > > Just for testing, I also tried a hack to make EDID reading fail > (return -EIO in the MSM dp_aux_transfer() function if msg->request < > 8). Before ${SUBJECT} patch I'd see these modes: > > #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > ...and after ${SUBJECT} patch I'd see: > > #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 > #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > ...so your patch causes 640x480 to be prioritized. That also doesn't > seem ideal. If it was ideal, the DRM core should have listed 640x480 > first. So this is a different display or these modes are coming due to the drm_add_modes_noedid() call because of the EDID read fail right? If its coming due to the drm_add_modes_noedid() call and then we are adding the 640x480 mode on top of that, like I mentioned in my previous comment, we can remove the call for the !edid case to address this. > > I'll repeat my refrain that I'm not a DRM expert, but if I were doing > things, I'd rather revert commit 8b2c181e3dcf ("drm/msm/dp: add fail > safe mode outside of event_mutex context") and commit d4aca422539c > ("drm/msm/dp: always add fail-safe mode into connector mode list") and > then go back and look more carefully about what the problem was in the > first place. Why didn't the failsafe modes added by the DRM core solve > the problem for you in the first place? I have explained why DRM core did not solve this problem. Thats because it will hit only when count of modes is 0, here count of modes is not 0. So we know the root-cause. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 1:42 ` Abhinav Kumar @ 2022-04-26 2:18 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 2:18 UTC (permalink / raw) To: Abhinav Kumar Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi, On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > >> 2) When there was a valid EDID but no 640x480 mode > >> > >> This is the equipment specific case and the one even I was a bit > >> surprised. There is a DP compliance equipment we have in-house and while > >> validation, it was found that in its list of modes , it did not have any > >> modes which chromebook supported ( due to 2 lanes ). But my > >> understanding was that, all sinks should have atleast 640x480 but > >> apparently this one did not have that. So to handle this DP compliance > >> equipment behavior, we had to do this. > > > > That doesn't seem right. If there's a valid EDID and the valid EDID > > doesn't contain 640x480, are you _sure_ you're supposed to be adding > > 640x480? That doesn't sound right to me. I've got a tiny display in > > front of me for testing that only has one mode: > > > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > > > > As I had wrote, DRM core kicks in only when the count of modes is 0. > Here what is happening is the count was not 0 but 640x480 was not > present in the EDID. So we had to add it explicitly. > > Your tiny display is a display port display? > > I am referring to only display port monitors. If your tiny display is > DP, it should have had 640x480 in its list of modes. My tiny display is actually a HDMI display hooked up to a HDMI to DP (active) adapter. ...but this is a legal and common thing to have. I suppose possibly my HDMI display is "illegal"? OK, so reading through the spec more carefully, I do see that the DP spec makes numerous mentions of the fact that DP sinks _must_ support 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video Timing Format" says that we must support 640x480. It seems like that's _intended_ to be used only if the EDID read fails, though or if we somehow have to output video without knowledge of the EDID. It seems hard to believe that there's a great reason to assume a display will support 640x480 if we have more accurate knowledge. In any case, I guess I would still say that adding this mode belongs in the DRM core. The core should notice that it's a DP connection (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was left out and it should add it. We should also make sure it's not "preferred" and is last in the list so we never accidentally pick it. If DP truly says that we should always give the user 640x480 then that's true for everyone, not just Qualcomm. We should add it in the core. If, later, someone wants to hide this from the UI it would be much easier if they only needed to modify one place. > > So IMO we _shouldn't_ land ${SUBJECT} patch. > > > > Just for testing, I also tried a hack to make EDID reading fail > > (return -EIO in the MSM dp_aux_transfer() function if msg->request < > > 8). Before ${SUBJECT} patch I'd see these modes: > > > > #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > > #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > > #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > > #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > > > ...and after ${SUBJECT} patch I'd see: > > > > #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > > #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > > #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > > #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > > > ...so your patch causes 640x480 to be prioritized. That also doesn't > > seem ideal. If it was ideal, the DRM core should have listed 640x480 > > first. > > So this is a different display or these modes are coming due to the > drm_add_modes_noedid() call because of the EDID read fail right? Right, it's from the !edid case. -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 2:18 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 2:18 UTC (permalink / raw) To: Abhinav Kumar Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi, On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > >> 2) When there was a valid EDID but no 640x480 mode > >> > >> This is the equipment specific case and the one even I was a bit > >> surprised. There is a DP compliance equipment we have in-house and while > >> validation, it was found that in its list of modes , it did not have any > >> modes which chromebook supported ( due to 2 lanes ). But my > >> understanding was that, all sinks should have atleast 640x480 but > >> apparently this one did not have that. So to handle this DP compliance > >> equipment behavior, we had to do this. > > > > That doesn't seem right. If there's a valid EDID and the valid EDID > > doesn't contain 640x480, are you _sure_ you're supposed to be adding > > 640x480? That doesn't sound right to me. I've got a tiny display in > > front of me for testing that only has one mode: > > > > #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > > > > As I had wrote, DRM core kicks in only when the count of modes is 0. > Here what is happening is the count was not 0 but 640x480 was not > present in the EDID. So we had to add it explicitly. > > Your tiny display is a display port display? > > I am referring to only display port monitors. If your tiny display is > DP, it should have had 640x480 in its list of modes. My tiny display is actually a HDMI display hooked up to a HDMI to DP (active) adapter. ...but this is a legal and common thing to have. I suppose possibly my HDMI display is "illegal"? OK, so reading through the spec more carefully, I do see that the DP spec makes numerous mentions of the fact that DP sinks _must_ support 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video Timing Format" says that we must support 640x480. It seems like that's _intended_ to be used only if the EDID read fails, though or if we somehow have to output video without knowledge of the EDID. It seems hard to believe that there's a great reason to assume a display will support 640x480 if we have more accurate knowledge. In any case, I guess I would still say that adding this mode belongs in the DRM core. The core should notice that it's a DP connection (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was left out and it should add it. We should also make sure it's not "preferred" and is last in the list so we never accidentally pick it. If DP truly says that we should always give the user 640x480 then that's true for everyone, not just Qualcomm. We should add it in the core. If, later, someone wants to hide this from the UI it would be much easier if they only needed to modify one place. > > So IMO we _shouldn't_ land ${SUBJECT} patch. > > > > Just for testing, I also tried a hack to make EDID reading fail > > (return -EIO in the MSM dp_aux_transfer() function if msg->request < > > 8). Before ${SUBJECT} patch I'd see these modes: > > > > #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > > #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > > #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > > #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > > > ...and after ${SUBJECT} patch I'd see: > > > > #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 > > #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 > > #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 > > #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 > > #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 > > > > ...so your patch causes 640x480 to be prioritized. That also doesn't > > seem ideal. If it was ideal, the DRM core should have listed 640x480 > > first. > > So this is a different display or these modes are coming due to the > drm_add_modes_noedid() call because of the EDID read fail right? Right, it's from the !edid case. -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 2:18 ` Doug Anderson @ 2022-04-26 3:35 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 3:35 UTC (permalink / raw) To: Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno On 4/25/2022 7:18 PM, Doug Anderson wrote: > Hi, > > On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >>>> 2) When there was a valid EDID but no 640x480 mode >>>> >>>> This is the equipment specific case and the one even I was a bit >>>> surprised. There is a DP compliance equipment we have in-house and while >>>> validation, it was found that in its list of modes , it did not have any >>>> modes which chromebook supported ( due to 2 lanes ). But my >>>> understanding was that, all sinks should have atleast 640x480 but >>>> apparently this one did not have that. So to handle this DP compliance >>>> equipment behavior, we had to do this. >>> >>> That doesn't seem right. If there's a valid EDID and the valid EDID >>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>> 640x480? That doesn't sound right to me. I've got a tiny display in >>> front of me for testing that only has one mode: >>> >>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>> >> >> As I had wrote, DRM core kicks in only when the count of modes is 0. >> Here what is happening is the count was not 0 but 640x480 was not >> present in the EDID. So we had to add it explicitly. >> >> Your tiny display is a display port display? >> >> I am referring to only display port monitors. If your tiny display is >> DP, it should have had 640x480 in its list of modes. > > My tiny display is actually a HDMI display hooked up to a HDMI to DP > (active) adapter. > > ...but this is a legal and common thing to have. I suppose possibly my > HDMI display is "illegal"? > > OK, so reading through the spec more carefully, I do see that the DP > spec makes numerous mentions of the fact that DP sinks _must_ support > 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > Timing Format" says that we must support 640x480. It seems like that's > _intended_ to be used only if the EDID read fails, though or if we > somehow have to output video without knowledge of the EDID. It seems > hard to believe that there's a great reason to assume a display will > support 640x480 if we have more accurate knowledge. > > In any case, I guess I would still say that adding this mode belongs > in the DRM core. The core should notice that it's a DP connection > (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > left out and it should add it. We should also make sure it's not > "preferred" and is last in the list so we never accidentally pick it. > If DP truly says that we should always give the user 640x480 then > that's true for everyone, not just Qualcomm. We should add it in the > core. If, later, someone wants to hide this from the UI it would be > much easier if they only needed to modify one place. > So I debugged with kuogee just now using the DP compliance equipment. It turns out, the issue is not that 640x480 mode is not present. The issue is that it is not marked as preferred. Hence we missed this part during debugging this equipment failure. We still have to figure out the best way to either mark 640x480 as preferred or eliminate other modes during the test-case so that 640x480 is actually picked by usermode. Now that being said, the fix still doesn't belong in the framework. It has to be in the msm/dp code. Different vendors handle this failure case differently looks like. Lets take below snippet from i915 as example. 3361 if (intel_connector->detect_edid == NULL || 3362 connector->edid_corrupt || 3363 intel_dp->aux.i2c_defer_count > 6) { 3364 /* Check EDID read for NACKs, DEFERs and corruption 3365 * (DP CTS 1.2 Core r1.1) 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER 3368 * 4.2.2.6 : EDID corruption detected 3369 * Use failsafe mode for all cases 3370 */ 3371 if (intel_dp->aux.i2c_nack_count > 0 || 3372 intel_dp->aux.i2c_defer_count > 0) 3373 drm_dbg_kms(&i915->drm, 3374 "EDID read had %d NACKs, %d DEFERs\n", 3375 intel_dp->aux.i2c_nack_count, 3376 intel_dp->aux.i2c_defer_count); 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; This marks the fail safe mode and IGT test case reads this to set this mode and hence the test passes. We rely on the chromeOS usermode to output pixel data for this test-case and not IGT. We use IGT only for video pattern CTS today but this is a different test-case which is failing. ChromeOS usermode will not pick 640x480 unless we mark it as preferred or other modes are eliminated. So we have to come up with the right way for the usermode to pick 640x480. We will discuss this a bit more and come up with a different change. > >>> So IMO we _shouldn't_ land ${SUBJECT} patch. >>> >>> Just for testing, I also tried a hack to make EDID reading fail >>> (return -EIO in the MSM dp_aux_transfer() function if msg->request < >>> 8). Before ${SUBJECT} patch I'd see these modes: >>> >>> #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 >>> #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 >>> #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 >>> #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 >>> #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 >>> >>> ...and after ${SUBJECT} patch I'd see: >>> >>> #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 >>> #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 >>> #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 >>> #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 >>> #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 >>> >>> ...so your patch causes 640x480 to be prioritized. That also doesn't >>> seem ideal. If it was ideal, the DRM core should have listed 640x480 >>> first. >> >> So this is a different display or these modes are coming due to the >> drm_add_modes_noedid() call because of the EDID read fail right? > > Right, it's from the !edid case. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 3:35 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 3:35 UTC (permalink / raw) To: Doug Anderson Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul On 4/25/2022 7:18 PM, Doug Anderson wrote: > Hi, > > On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >>>> 2) When there was a valid EDID but no 640x480 mode >>>> >>>> This is the equipment specific case and the one even I was a bit >>>> surprised. There is a DP compliance equipment we have in-house and while >>>> validation, it was found that in its list of modes , it did not have any >>>> modes which chromebook supported ( due to 2 lanes ). But my >>>> understanding was that, all sinks should have atleast 640x480 but >>>> apparently this one did not have that. So to handle this DP compliance >>>> equipment behavior, we had to do this. >>> >>> That doesn't seem right. If there's a valid EDID and the valid EDID >>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>> 640x480? That doesn't sound right to me. I've got a tiny display in >>> front of me for testing that only has one mode: >>> >>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>> >> >> As I had wrote, DRM core kicks in only when the count of modes is 0. >> Here what is happening is the count was not 0 but 640x480 was not >> present in the EDID. So we had to add it explicitly. >> >> Your tiny display is a display port display? >> >> I am referring to only display port monitors. If your tiny display is >> DP, it should have had 640x480 in its list of modes. > > My tiny display is actually a HDMI display hooked up to a HDMI to DP > (active) adapter. > > ...but this is a legal and common thing to have. I suppose possibly my > HDMI display is "illegal"? > > OK, so reading through the spec more carefully, I do see that the DP > spec makes numerous mentions of the fact that DP sinks _must_ support > 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > Timing Format" says that we must support 640x480. It seems like that's > _intended_ to be used only if the EDID read fails, though or if we > somehow have to output video without knowledge of the EDID. It seems > hard to believe that there's a great reason to assume a display will > support 640x480 if we have more accurate knowledge. > > In any case, I guess I would still say that adding this mode belongs > in the DRM core. The core should notice that it's a DP connection > (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > left out and it should add it. We should also make sure it's not > "preferred" and is last in the list so we never accidentally pick it. > If DP truly says that we should always give the user 640x480 then > that's true for everyone, not just Qualcomm. We should add it in the > core. If, later, someone wants to hide this from the UI it would be > much easier if they only needed to modify one place. > So I debugged with kuogee just now using the DP compliance equipment. It turns out, the issue is not that 640x480 mode is not present. The issue is that it is not marked as preferred. Hence we missed this part during debugging this equipment failure. We still have to figure out the best way to either mark 640x480 as preferred or eliminate other modes during the test-case so that 640x480 is actually picked by usermode. Now that being said, the fix still doesn't belong in the framework. It has to be in the msm/dp code. Different vendors handle this failure case differently looks like. Lets take below snippet from i915 as example. 3361 if (intel_connector->detect_edid == NULL || 3362 connector->edid_corrupt || 3363 intel_dp->aux.i2c_defer_count > 6) { 3364 /* Check EDID read for NACKs, DEFERs and corruption 3365 * (DP CTS 1.2 Core r1.1) 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER 3368 * 4.2.2.6 : EDID corruption detected 3369 * Use failsafe mode for all cases 3370 */ 3371 if (intel_dp->aux.i2c_nack_count > 0 || 3372 intel_dp->aux.i2c_defer_count > 0) 3373 drm_dbg_kms(&i915->drm, 3374 "EDID read had %d NACKs, %d DEFERs\n", 3375 intel_dp->aux.i2c_nack_count, 3376 intel_dp->aux.i2c_defer_count); 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; This marks the fail safe mode and IGT test case reads this to set this mode and hence the test passes. We rely on the chromeOS usermode to output pixel data for this test-case and not IGT. We use IGT only for video pattern CTS today but this is a different test-case which is failing. ChromeOS usermode will not pick 640x480 unless we mark it as preferred or other modes are eliminated. So we have to come up with the right way for the usermode to pick 640x480. We will discuss this a bit more and come up with a different change. > >>> So IMO we _shouldn't_ land ${SUBJECT} patch. >>> >>> Just for testing, I also tried a hack to make EDID reading fail >>> (return -EIO in the MSM dp_aux_transfer() function if msg->request < >>> 8). Before ${SUBJECT} patch I'd see these modes: >>> >>> #0 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 >>> #1 800x600 60.32 800 840 968 1056 600 601 605 628 40000 >>> #2 800x600 56.25 800 824 896 1024 600 601 603 625 36000 >>> #3 848x480 60.00 848 864 976 1088 480 486 494 517 33750 >>> #4 640x480 59.94 640 656 752 800 480 490 492 525 25175 >>> >>> ...and after ${SUBJECT} patch I'd see: >>> >>> #0 640x480 59.94 640 656 752 800 480 490 492 525 25175 >>> #1 1024x768 60.00 1024 1048 1184 1344 768 771 777 806 65000 >>> #2 800x600 60.32 800 840 968 1056 600 601 605 628 40000 >>> #3 800x600 56.25 800 824 896 1024 600 601 603 625 36000 >>> #4 848x480 60.00 848 864 976 1088 480 486 494 517 33750 >>> >>> ...so your patch causes 640x480 to be prioritized. That also doesn't >>> seem ideal. If it was ideal, the DRM core should have listed 640x480 >>> first. >> >> So this is a different display or these modes are coming due to the >> drm_add_modes_noedid() call because of the EDID read fail right? > > Right, it's from the !edid case. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 3:35 ` Abhinav Kumar @ 2022-04-26 15:20 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 15:20 UTC (permalink / raw) To: Abhinav Kumar Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi, On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > On 4/25/2022 7:18 PM, Doug Anderson wrote: > > Hi, > > > > On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > >> > >>>> 2) When there was a valid EDID but no 640x480 mode > >>>> > >>>> This is the equipment specific case and the one even I was a bit > >>>> surprised. There is a DP compliance equipment we have in-house and while > >>>> validation, it was found that in its list of modes , it did not have any > >>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>> understanding was that, all sinks should have atleast 640x480 but > >>>> apparently this one did not have that. So to handle this DP compliance > >>>> equipment behavior, we had to do this. > >>> > >>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>> front of me for testing that only has one mode: > >>> > >>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>> > >> > >> As I had wrote, DRM core kicks in only when the count of modes is 0. > >> Here what is happening is the count was not 0 but 640x480 was not > >> present in the EDID. So we had to add it explicitly. > >> > >> Your tiny display is a display port display? > >> > >> I am referring to only display port monitors. If your tiny display is > >> DP, it should have had 640x480 in its list of modes. > > > > My tiny display is actually a HDMI display hooked up to a HDMI to DP > > (active) adapter. > > > > ...but this is a legal and common thing to have. I suppose possibly my > > HDMI display is "illegal"? > > > > OK, so reading through the spec more carefully, I do see that the DP > > spec makes numerous mentions of the fact that DP sinks _must_ support > > 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > > Timing Format" says that we must support 640x480. It seems like that's > > _intended_ to be used only if the EDID read fails, though or if we > > somehow have to output video without knowledge of the EDID. It seems > > hard to believe that there's a great reason to assume a display will > > support 640x480 if we have more accurate knowledge. > > > > In any case, I guess I would still say that adding this mode belongs > > in the DRM core. The core should notice that it's a DP connection > > (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > > left out and it should add it. We should also make sure it's not > > "preferred" and is last in the list so we never accidentally pick it. > > If DP truly says that we should always give the user 640x480 then > > that's true for everyone, not just Qualcomm. We should add it in the > > core. If, later, someone wants to hide this from the UI it would be > > much easier if they only needed to modify one place. > > > > So I debugged with kuogee just now using the DP compliance equipment. > It turns out, the issue is not that 640x480 mode is not present. > > The issue is that it is not marked as preferred. > > Hence we missed this part during debugging this equipment failure. > > We still have to figure out the best way to either mark 640x480 as > preferred or eliminate other modes during the test-case so that 640x480 > is actually picked by usermode. > > Now that being said, the fix still doesn't belong in the framework. It > has to be in the msm/dp code. > > Different vendors handle this failure case differently looks like. > > Lets take below snippet from i915 as example. > > 3361 if (intel_connector->detect_edid == NULL || > 3362 connector->edid_corrupt || > 3363 intel_dp->aux.i2c_defer_count > 6) { > 3364 /* Check EDID read for NACKs, DEFERs and corruption > 3365 * (DP CTS 1.2 Core r1.1) > 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > 3368 * 4.2.2.6 : EDID corruption detected > 3369 * Use failsafe mode for all cases > 3370 */ > 3371 if (intel_dp->aux.i2c_nack_count > 0 || > 3372 intel_dp->aux.i2c_defer_count > 0) > 3373 drm_dbg_kms(&i915->drm, > 3374 "EDID read had %d NACKs, %d DEFERs\n", > 3375 intel_dp->aux.i2c_nack_count, > 3376 intel_dp->aux.i2c_defer_count); > 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; Just because Intel DRM has its own solution for something doesn't mean everyone else should copy them and implement their own solution. Up until recently DP AUX backlights were baked into different DRM drivers. A recent effort was made to pull it out. I think the Intel DRM code was the "first one" to the party and it wasn't clear how things should be broken up to share with other drivers, so mostly it did everything itself, but that's not the long term answer. I'm not saying that we need to block your change on a full re-design or anything, but I'm just saying that: * You're trying to implement a generic DP rule, not something specific to Qualcomm hardware. That implies that, if possible, it shouldn't be in a Qualcomm driver. * It doesn't seem like it would be terrible to handle this in the core. > This marks the fail safe mode and IGT test case reads this to set this > mode and hence the test passes. > > We rely on the chromeOS usermode to output pixel data for this test-case > and not IGT. We use IGT only for video pattern CTS today but this is a > different test-case which is failing. > > ChromeOS usermode will not pick 640x480 unless we mark it as preferred > or other modes are eliminated. > > So we have to come up with the right way for the usermode to pick 640x480. > > We will discuss this a bit more and come up with a different change. Can you provide the exact EDID from the failing test case? Maybe that will help shed some light on what's going on. I looked at the original commit and it just referred to 4.2.2.1, which I assume is "EDID Read upon HPD Plug Event", but that doesn't give details that seem relevant to the discussion here. I guess maybe what's happening is that the test case is giving an EDID where all the modes are not supportable by the current clock rate / lanes? ...and then somehow we're not falling back to 640x480. It's always possible that this is a userspace problem. In any case, would you object to a revert of the patches in the short term? -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 15:20 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 15:20 UTC (permalink / raw) To: Abhinav Kumar Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi, On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > On 4/25/2022 7:18 PM, Doug Anderson wrote: > > Hi, > > > > On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > >> > >>>> 2) When there was a valid EDID but no 640x480 mode > >>>> > >>>> This is the equipment specific case and the one even I was a bit > >>>> surprised. There is a DP compliance equipment we have in-house and while > >>>> validation, it was found that in its list of modes , it did not have any > >>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>> understanding was that, all sinks should have atleast 640x480 but > >>>> apparently this one did not have that. So to handle this DP compliance > >>>> equipment behavior, we had to do this. > >>> > >>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>> front of me for testing that only has one mode: > >>> > >>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>> > >> > >> As I had wrote, DRM core kicks in only when the count of modes is 0. > >> Here what is happening is the count was not 0 but 640x480 was not > >> present in the EDID. So we had to add it explicitly. > >> > >> Your tiny display is a display port display? > >> > >> I am referring to only display port monitors. If your tiny display is > >> DP, it should have had 640x480 in its list of modes. > > > > My tiny display is actually a HDMI display hooked up to a HDMI to DP > > (active) adapter. > > > > ...but this is a legal and common thing to have. I suppose possibly my > > HDMI display is "illegal"? > > > > OK, so reading through the spec more carefully, I do see that the DP > > spec makes numerous mentions of the fact that DP sinks _must_ support > > 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > > Timing Format" says that we must support 640x480. It seems like that's > > _intended_ to be used only if the EDID read fails, though or if we > > somehow have to output video without knowledge of the EDID. It seems > > hard to believe that there's a great reason to assume a display will > > support 640x480 if we have more accurate knowledge. > > > > In any case, I guess I would still say that adding this mode belongs > > in the DRM core. The core should notice that it's a DP connection > > (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > > left out and it should add it. We should also make sure it's not > > "preferred" and is last in the list so we never accidentally pick it. > > If DP truly says that we should always give the user 640x480 then > > that's true for everyone, not just Qualcomm. We should add it in the > > core. If, later, someone wants to hide this from the UI it would be > > much easier if they only needed to modify one place. > > > > So I debugged with kuogee just now using the DP compliance equipment. > It turns out, the issue is not that 640x480 mode is not present. > > The issue is that it is not marked as preferred. > > Hence we missed this part during debugging this equipment failure. > > We still have to figure out the best way to either mark 640x480 as > preferred or eliminate other modes during the test-case so that 640x480 > is actually picked by usermode. > > Now that being said, the fix still doesn't belong in the framework. It > has to be in the msm/dp code. > > Different vendors handle this failure case differently looks like. > > Lets take below snippet from i915 as example. > > 3361 if (intel_connector->detect_edid == NULL || > 3362 connector->edid_corrupt || > 3363 intel_dp->aux.i2c_defer_count > 6) { > 3364 /* Check EDID read for NACKs, DEFERs and corruption > 3365 * (DP CTS 1.2 Core r1.1) > 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > 3368 * 4.2.2.6 : EDID corruption detected > 3369 * Use failsafe mode for all cases > 3370 */ > 3371 if (intel_dp->aux.i2c_nack_count > 0 || > 3372 intel_dp->aux.i2c_defer_count > 0) > 3373 drm_dbg_kms(&i915->drm, > 3374 "EDID read had %d NACKs, %d DEFERs\n", > 3375 intel_dp->aux.i2c_nack_count, > 3376 intel_dp->aux.i2c_defer_count); > 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; Just because Intel DRM has its own solution for something doesn't mean everyone else should copy them and implement their own solution. Up until recently DP AUX backlights were baked into different DRM drivers. A recent effort was made to pull it out. I think the Intel DRM code was the "first one" to the party and it wasn't clear how things should be broken up to share with other drivers, so mostly it did everything itself, but that's not the long term answer. I'm not saying that we need to block your change on a full re-design or anything, but I'm just saying that: * You're trying to implement a generic DP rule, not something specific to Qualcomm hardware. That implies that, if possible, it shouldn't be in a Qualcomm driver. * It doesn't seem like it would be terrible to handle this in the core. > This marks the fail safe mode and IGT test case reads this to set this > mode and hence the test passes. > > We rely on the chromeOS usermode to output pixel data for this test-case > and not IGT. We use IGT only for video pattern CTS today but this is a > different test-case which is failing. > > ChromeOS usermode will not pick 640x480 unless we mark it as preferred > or other modes are eliminated. > > So we have to come up with the right way for the usermode to pick 640x480. > > We will discuss this a bit more and come up with a different change. Can you provide the exact EDID from the failing test case? Maybe that will help shed some light on what's going on. I looked at the original commit and it just referred to 4.2.2.1, which I assume is "EDID Read upon HPD Plug Event", but that doesn't give details that seem relevant to the discussion here. I guess maybe what's happening is that the test case is giving an EDID where all the modes are not supportable by the current clock rate / lanes? ...and then somehow we're not falling back to 640x480. It's always possible that this is a userspace problem. In any case, would you object to a revert of the patches in the short term? -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 15:20 ` Doug Anderson @ 2022-04-26 15:37 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 15:37 UTC (permalink / raw) To: Doug Anderson Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi Doug On 4/26/2022 8:20 AM, Doug Anderson wrote: > Hi, > > On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>> Hi, >>> >>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >>>> >>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>> >>>>>> This is the equipment specific case and the one even I was a bit >>>>>> surprised. There is a DP compliance equipment we have in-house and while >>>>>> validation, it was found that in its list of modes , it did not have any >>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>> apparently this one did not have that. So to handle this DP compliance >>>>>> equipment behavior, we had to do this. >>>>> >>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>> front of me for testing that only has one mode: >>>>> >>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>> >>>> >>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>> Here what is happening is the count was not 0 but 640x480 was not >>>> present in the EDID. So we had to add it explicitly. >>>> >>>> Your tiny display is a display port display? >>>> >>>> I am referring to only display port monitors. If your tiny display is >>>> DP, it should have had 640x480 in its list of modes. >>> >>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>> (active) adapter. >>> >>> ...but this is a legal and common thing to have. I suppose possibly my >>> HDMI display is "illegal"? >>> >>> OK, so reading through the spec more carefully, I do see that the DP >>> spec makes numerous mentions of the fact that DP sinks _must_ support >>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>> Timing Format" says that we must support 640x480. It seems like that's >>> _intended_ to be used only if the EDID read fails, though or if we >>> somehow have to output video without knowledge of the EDID. It seems >>> hard to believe that there's a great reason to assume a display will >>> support 640x480 if we have more accurate knowledge. >>> >>> In any case, I guess I would still say that adding this mode belongs >>> in the DRM core. The core should notice that it's a DP connection >>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>> left out and it should add it. We should also make sure it's not >>> "preferred" and is last in the list so we never accidentally pick it. >>> If DP truly says that we should always give the user 640x480 then >>> that's true for everyone, not just Qualcomm. We should add it in the >>> core. If, later, someone wants to hide this from the UI it would be >>> much easier if they only needed to modify one place. >>> >> >> So I debugged with kuogee just now using the DP compliance equipment. >> It turns out, the issue is not that 640x480 mode is not present. >> >> The issue is that it is not marked as preferred. >> >> Hence we missed this part during debugging this equipment failure. >> >> We still have to figure out the best way to either mark 640x480 as >> preferred or eliminate other modes during the test-case so that 640x480 >> is actually picked by usermode. >> >> Now that being said, the fix still doesn't belong in the framework. It >> has to be in the msm/dp code. >> >> Different vendors handle this failure case differently looks like. >> >> Lets take below snippet from i915 as example. >> >> 3361 if (intel_connector->detect_edid == NULL || >> 3362 connector->edid_corrupt || >> 3363 intel_dp->aux.i2c_defer_count > 6) { >> 3364 /* Check EDID read for NACKs, DEFERs and corruption >> 3365 * (DP CTS 1.2 Core r1.1) >> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >> 3368 * 4.2.2.6 : EDID corruption detected >> 3369 * Use failsafe mode for all cases >> 3370 */ >> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >> 3372 intel_dp->aux.i2c_defer_count > 0) >> 3373 drm_dbg_kms(&i915->drm, >> 3374 "EDID read had %d NACKs, %d DEFERs\n", >> 3375 intel_dp->aux.i2c_nack_count, >> 3376 intel_dp->aux.i2c_defer_count); >> 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; > The reason I pointed to this code is to give an example of how other drivers handle this test-case. We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. The challenge here as found out from our discussion here was to mark a particular mode as preferred so that the Chrome usermode can pick it. Now whats happening with that there was always a possibility of two modes being marked as preferred due to this and so-on. We had a pretty long discussion last night and thought of all possible solutions but all of them look like a hack to us in the driver because we end up breaking other things due to this. So we decided that driver is not the place to handle this test case. Since we do have IGT support for chromebooks, we will handle both these test cases there as other vendors do the same way and it works. > Just because Intel DRM has its own solution for something doesn't mean > everyone else should copy them and implement their own solution. Up > until recently DP AUX backlights were baked into different DRM > drivers. A recent effort was made to pull it out. I think the Intel > DRM code was the "first one" to the party and it wasn't clear how > things should be broken up to share with other drivers, so mostly it > did everything itself, but that's not the long term answer. > > I'm not saying that we need to block your change on a full re-design > or anything, but I'm just saying that: > > * You're trying to implement a generic DP rule, not something specific > to Qualcomm hardware. That implies that, if possible, it shouldn't be > in a Qualcomm driver. > > * It doesn't seem like it would be terrible to handle this in the core. > > >> This marks the fail safe mode and IGT test case reads this to set this >> mode and hence the test passes. >> >> We rely on the chromeOS usermode to output pixel data for this test-case >> and not IGT. We use IGT only for video pattern CTS today but this is a >> different test-case which is failing. >> >> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >> or other modes are eliminated. >> >> So we have to come up with the right way for the usermode to pick 640x480. >> >> We will discuss this a bit more and come up with a different change. > > Can you provide the exact EDID from the failing test case? Maybe that > will help shed some light on what's going on. I looked at the original > commit and it just referred to 4.2.2.1, which I assume is "EDID Read > upon HPD Plug Event", but that doesn't give details that seem relevant > to the discussion here. Yes so it is 4.2.2.1 and 4.2.2.6. That alone wont give the full picture. So its a combination of things. While running the test, the test equipment published only one mode. But we could not support that mode because of 2 lanes. Equipment did not add 640x480 to the list of modes. DRM fwk will also not add it because count_modes is not 0 ( there was one mode ). So we ended up making these changes. > > I guess maybe what's happening is that the test case is giving an EDID > where all the modes are not supportable by the current clock rate / > lanes? ...and then somehow we're not falling back to 640x480. It's > always possible that this is a userspace problem. > > In any case, would you object to a revert of the patches in the short term? Not sure, if you saw this change kuogee posted last night. https://patchwork.freedesktop.org/patch/483415/ We did decided to remove all the code related to these test cases and handle them in IGT. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 15:37 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 15:37 UTC (permalink / raw) To: Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi Doug On 4/26/2022 8:20 AM, Doug Anderson wrote: > Hi, > > On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >> >> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>> Hi, >>> >>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: >>>> >>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>> >>>>>> This is the equipment specific case and the one even I was a bit >>>>>> surprised. There is a DP compliance equipment we have in-house and while >>>>>> validation, it was found that in its list of modes , it did not have any >>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>> apparently this one did not have that. So to handle this DP compliance >>>>>> equipment behavior, we had to do this. >>>>> >>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>> front of me for testing that only has one mode: >>>>> >>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>> >>>> >>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>> Here what is happening is the count was not 0 but 640x480 was not >>>> present in the EDID. So we had to add it explicitly. >>>> >>>> Your tiny display is a display port display? >>>> >>>> I am referring to only display port monitors. If your tiny display is >>>> DP, it should have had 640x480 in its list of modes. >>> >>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>> (active) adapter. >>> >>> ...but this is a legal and common thing to have. I suppose possibly my >>> HDMI display is "illegal"? >>> >>> OK, so reading through the spec more carefully, I do see that the DP >>> spec makes numerous mentions of the fact that DP sinks _must_ support >>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>> Timing Format" says that we must support 640x480. It seems like that's >>> _intended_ to be used only if the EDID read fails, though or if we >>> somehow have to output video without knowledge of the EDID. It seems >>> hard to believe that there's a great reason to assume a display will >>> support 640x480 if we have more accurate knowledge. >>> >>> In any case, I guess I would still say that adding this mode belongs >>> in the DRM core. The core should notice that it's a DP connection >>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>> left out and it should add it. We should also make sure it's not >>> "preferred" and is last in the list so we never accidentally pick it. >>> If DP truly says that we should always give the user 640x480 then >>> that's true for everyone, not just Qualcomm. We should add it in the >>> core. If, later, someone wants to hide this from the UI it would be >>> much easier if they only needed to modify one place. >>> >> >> So I debugged with kuogee just now using the DP compliance equipment. >> It turns out, the issue is not that 640x480 mode is not present. >> >> The issue is that it is not marked as preferred. >> >> Hence we missed this part during debugging this equipment failure. >> >> We still have to figure out the best way to either mark 640x480 as >> preferred or eliminate other modes during the test-case so that 640x480 >> is actually picked by usermode. >> >> Now that being said, the fix still doesn't belong in the framework. It >> has to be in the msm/dp code. >> >> Different vendors handle this failure case differently looks like. >> >> Lets take below snippet from i915 as example. >> >> 3361 if (intel_connector->detect_edid == NULL || >> 3362 connector->edid_corrupt || >> 3363 intel_dp->aux.i2c_defer_count > 6) { >> 3364 /* Check EDID read for NACKs, DEFERs and corruption >> 3365 * (DP CTS 1.2 Core r1.1) >> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >> 3368 * 4.2.2.6 : EDID corruption detected >> 3369 * Use failsafe mode for all cases >> 3370 */ >> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >> 3372 intel_dp->aux.i2c_defer_count > 0) >> 3373 drm_dbg_kms(&i915->drm, >> 3374 "EDID read had %d NACKs, %d DEFERs\n", >> 3375 intel_dp->aux.i2c_nack_count, >> 3376 intel_dp->aux.i2c_defer_count); >> 3377 intel_dp->compliance.test_data.edid = INTEL_DP_RESOLUTION_FAILSAFE; > The reason I pointed to this code is to give an example of how other drivers handle this test-case. We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. The challenge here as found out from our discussion here was to mark a particular mode as preferred so that the Chrome usermode can pick it. Now whats happening with that there was always a possibility of two modes being marked as preferred due to this and so-on. We had a pretty long discussion last night and thought of all possible solutions but all of them look like a hack to us in the driver because we end up breaking other things due to this. So we decided that driver is not the place to handle this test case. Since we do have IGT support for chromebooks, we will handle both these test cases there as other vendors do the same way and it works. > Just because Intel DRM has its own solution for something doesn't mean > everyone else should copy them and implement their own solution. Up > until recently DP AUX backlights were baked into different DRM > drivers. A recent effort was made to pull it out. I think the Intel > DRM code was the "first one" to the party and it wasn't clear how > things should be broken up to share with other drivers, so mostly it > did everything itself, but that's not the long term answer. > > I'm not saying that we need to block your change on a full re-design > or anything, but I'm just saying that: > > * You're trying to implement a generic DP rule, not something specific > to Qualcomm hardware. That implies that, if possible, it shouldn't be > in a Qualcomm driver. > > * It doesn't seem like it would be terrible to handle this in the core. > > >> This marks the fail safe mode and IGT test case reads this to set this >> mode and hence the test passes. >> >> We rely on the chromeOS usermode to output pixel data for this test-case >> and not IGT. We use IGT only for video pattern CTS today but this is a >> different test-case which is failing. >> >> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >> or other modes are eliminated. >> >> So we have to come up with the right way for the usermode to pick 640x480. >> >> We will discuss this a bit more and come up with a different change. > > Can you provide the exact EDID from the failing test case? Maybe that > will help shed some light on what's going on. I looked at the original > commit and it just referred to 4.2.2.1, which I assume is "EDID Read > upon HPD Plug Event", but that doesn't give details that seem relevant > to the discussion here. Yes so it is 4.2.2.1 and 4.2.2.6. That alone wont give the full picture. So its a combination of things. While running the test, the test equipment published only one mode. But we could not support that mode because of 2 lanes. Equipment did not add 640x480 to the list of modes. DRM fwk will also not add it because count_modes is not 0 ( there was one mode ). So we ended up making these changes. > > I guess maybe what's happening is that the test case is giving an EDID > where all the modes are not supportable by the current clock rate / > lanes? ...and then somehow we're not falling back to 640x480. It's > always possible that this is a userspace problem. > > In any case, would you object to a revert of the patches in the short term? Not sure, if you saw this change kuogee posted last night. https://patchwork.freedesktop.org/patch/483415/ We did decided to remove all the code related to these test cases and handle them in IGT. > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 15:37 ` Abhinav Kumar @ 2022-04-26 17:01 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 17:01 UTC (permalink / raw) To: Abhinav Kumar, Doug Anderson Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul On 26/04/2022 18:37, Abhinav Kumar wrote: > Hi Doug > > On 4/26/2022 8:20 AM, Doug Anderson wrote: >> Hi, >> >> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >> <quic_abhinavk@quicinc.com> wrote: >>> >>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>> >>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>> and while >>>>>>> validation, it was found that in its list of modes , it did not >>>>>>> have any >>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>> apparently this one did not have that. So to handle this DP >>>>>>> compliance >>>>>>> equipment behavior, we had to do this. >>>>>> >>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>> front of me for testing that only has one mode: >>>>>> >>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>> >>>>> >>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>> present in the EDID. So we had to add it explicitly. >>>>> >>>>> Your tiny display is a display port display? >>>>> >>>>> I am referring to only display port monitors. If your tiny display is >>>>> DP, it should have had 640x480 in its list of modes. >>>> >>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>> (active) adapter. >>>> >>>> ...but this is a legal and common thing to have. I suppose possibly my >>>> HDMI display is "illegal"? >>>> >>>> OK, so reading through the spec more carefully, I do see that the DP >>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>> Timing Format" says that we must support 640x480. It seems like that's >>>> _intended_ to be used only if the EDID read fails, though or if we >>>> somehow have to output video without knowledge of the EDID. It seems >>>> hard to believe that there's a great reason to assume a display will >>>> support 640x480 if we have more accurate knowledge. >>>> >>>> In any case, I guess I would still say that adding this mode belongs >>>> in the DRM core. The core should notice that it's a DP connection >>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>> left out and it should add it. We should also make sure it's not >>>> "preferred" and is last in the list so we never accidentally pick it. >>>> If DP truly says that we should always give the user 640x480 then >>>> that's true for everyone, not just Qualcomm. We should add it in the >>>> core. If, later, someone wants to hide this from the UI it would be >>>> much easier if they only needed to modify one place. >>>> >>> >>> So I debugged with kuogee just now using the DP compliance equipment. >>> It turns out, the issue is not that 640x480 mode is not present. >>> >>> The issue is that it is not marked as preferred. >>> >>> Hence we missed this part during debugging this equipment failure. >>> >>> We still have to figure out the best way to either mark 640x480 as >>> preferred or eliminate other modes during the test-case so that 640x480 >>> is actually picked by usermode. >>> >>> Now that being said, the fix still doesn't belong in the framework. It >>> has to be in the msm/dp code. >>> >>> Different vendors handle this failure case differently looks like. >>> >>> Lets take below snippet from i915 as example. >>> >>> 3361 if (intel_connector->detect_edid == NULL || >>> 3362 connector->edid_corrupt || >>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>> 3365 * (DP CTS 1.2 Core r1.1) >>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>> 3368 * 4.2.2.6 : EDID corruption detected >>> 3369 * Use failsafe mode for all cases >>> 3370 */ >>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>> 3372 intel_dp->aux.i2c_defer_count > 0) >>> 3373 drm_dbg_kms(&i915->drm, >>> 3374 "EDID read had %d NACKs, %d >>> DEFERs\n", >>> 3375 intel_dp->aux.i2c_nack_count, >>> 3376 intel_dp->aux.i2c_defer_count); >>> 3377 intel_dp->compliance.test_data.edid = >>> INTEL_DP_RESOLUTION_FAILSAFE; >> > > The reason I pointed to this code is to give an example of how other > drivers handle this test-case. > > We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > > The challenge here as found out from our discussion here was to mark a > particular mode as preferred so that the Chrome usermode can pick it. > > Now whats happening with that there was always a possibility of two > modes being marked as preferred due to this and so-on. > > We had a pretty long discussion last night and thought of all possible > solutions but all of them look like a hack to us in the driver because > we end up breaking other things due to this. > > So we decided that driver is not the place to handle this test case. > Since we do have IGT support for chromebooks, we will handle both these > test cases there as other vendors do the same way and it works. > > >> Just because Intel DRM has its own solution for something doesn't mean >> everyone else should copy them and implement their own solution. Up >> until recently DP AUX backlights were baked into different DRM >> drivers. A recent effort was made to pull it out. I think the Intel >> DRM code was the "first one" to the party and it wasn't clear how >> things should be broken up to share with other drivers, so mostly it >> did everything itself, but that's not the long term answer. >> >> I'm not saying that we need to block your change on a full re-design >> or anything, but I'm just saying that: >> >> * You're trying to implement a generic DP rule, not something specific >> to Qualcomm hardware. That implies that, if possible, it shouldn't be >> in a Qualcomm driver. >> >> * It doesn't seem like it would be terrible to handle this in the core. >> >> >>> This marks the fail safe mode and IGT test case reads this to set this >>> mode and hence the test passes. >>> >>> We rely on the chromeOS usermode to output pixel data for this test-case >>> and not IGT. We use IGT only for video pattern CTS today but this is a >>> different test-case which is failing. >>> >>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>> or other modes are eliminated. >>> >>> So we have to come up with the right way for the usermode to pick >>> 640x480. >>> >>> We will discuss this a bit more and come up with a different change. >> >> Can you provide the exact EDID from the failing test case? Maybe that >> will help shed some light on what's going on. I looked at the original >> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >> upon HPD Plug Event", but that doesn't give details that seem relevant >> to the discussion here. > > Yes so it is 4.2.2.1 and 4.2.2.6. > > That alone wont give the full picture. > > So its a combination of things. > > While running the test, the test equipment published only one mode. > But we could not support that mode because of 2 lanes. > Equipment did not add 640x480 to the list of modes. > DRM fwk will also not add it because count_modes is not 0 ( there was > one mode ). > So we ended up making these changes. I think a proper solution might be to rewrite drm_helper_probe_single_connector_modes() in the following way: - call get_modes() - validate the result - prune invalid - if the number of modes is 0, call drm_add_override_edid_modes() - validate the result - prune invalid - if the number of modes is still 0, call drm_add_modes_noedid() - validate the result - prune invalid [A separate change might happen here after all the checks: if the number of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o validation. But generally I feel that this shouldn't be necessary because the previous step should have added it.] This way we can be sure that all modes are validated, but still to do our best to add something supported to the list of modes. > > >> >> I guess maybe what's happening is that the test case is giving an EDID >> where all the modes are not supportable by the current clock rate / >> lanes? ...and then somehow we're not falling back to 640x480. It's >> always possible that this is a userspace problem. >> >> In any case, would you object to a revert of the patches in the short >> term? > > Not sure, if you saw this change kuogee posted last night. > https://patchwork.freedesktop.org/patch/483415/ > We did decided to remove all the code related to these test cases and > handle them in IGT. > >> >> -Doug -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 17:01 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 17:01 UTC (permalink / raw) To: Abhinav Kumar, Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno On 26/04/2022 18:37, Abhinav Kumar wrote: > Hi Doug > > On 4/26/2022 8:20 AM, Doug Anderson wrote: >> Hi, >> >> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >> <quic_abhinavk@quicinc.com> wrote: >>> >>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>> >>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>> and while >>>>>>> validation, it was found that in its list of modes , it did not >>>>>>> have any >>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>> apparently this one did not have that. So to handle this DP >>>>>>> compliance >>>>>>> equipment behavior, we had to do this. >>>>>> >>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>> front of me for testing that only has one mode: >>>>>> >>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>> >>>>> >>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>> present in the EDID. So we had to add it explicitly. >>>>> >>>>> Your tiny display is a display port display? >>>>> >>>>> I am referring to only display port monitors. If your tiny display is >>>>> DP, it should have had 640x480 in its list of modes. >>>> >>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>> (active) adapter. >>>> >>>> ...but this is a legal and common thing to have. I suppose possibly my >>>> HDMI display is "illegal"? >>>> >>>> OK, so reading through the spec more carefully, I do see that the DP >>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>> Timing Format" says that we must support 640x480. It seems like that's >>>> _intended_ to be used only if the EDID read fails, though or if we >>>> somehow have to output video without knowledge of the EDID. It seems >>>> hard to believe that there's a great reason to assume a display will >>>> support 640x480 if we have more accurate knowledge. >>>> >>>> In any case, I guess I would still say that adding this mode belongs >>>> in the DRM core. The core should notice that it's a DP connection >>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>> left out and it should add it. We should also make sure it's not >>>> "preferred" and is last in the list so we never accidentally pick it. >>>> If DP truly says that we should always give the user 640x480 then >>>> that's true for everyone, not just Qualcomm. We should add it in the >>>> core. If, later, someone wants to hide this from the UI it would be >>>> much easier if they only needed to modify one place. >>>> >>> >>> So I debugged with kuogee just now using the DP compliance equipment. >>> It turns out, the issue is not that 640x480 mode is not present. >>> >>> The issue is that it is not marked as preferred. >>> >>> Hence we missed this part during debugging this equipment failure. >>> >>> We still have to figure out the best way to either mark 640x480 as >>> preferred or eliminate other modes during the test-case so that 640x480 >>> is actually picked by usermode. >>> >>> Now that being said, the fix still doesn't belong in the framework. It >>> has to be in the msm/dp code. >>> >>> Different vendors handle this failure case differently looks like. >>> >>> Lets take below snippet from i915 as example. >>> >>> 3361 if (intel_connector->detect_edid == NULL || >>> 3362 connector->edid_corrupt || >>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>> 3365 * (DP CTS 1.2 Core r1.1) >>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>> 3368 * 4.2.2.6 : EDID corruption detected >>> 3369 * Use failsafe mode for all cases >>> 3370 */ >>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>> 3372 intel_dp->aux.i2c_defer_count > 0) >>> 3373 drm_dbg_kms(&i915->drm, >>> 3374 "EDID read had %d NACKs, %d >>> DEFERs\n", >>> 3375 intel_dp->aux.i2c_nack_count, >>> 3376 intel_dp->aux.i2c_defer_count); >>> 3377 intel_dp->compliance.test_data.edid = >>> INTEL_DP_RESOLUTION_FAILSAFE; >> > > The reason I pointed to this code is to give an example of how other > drivers handle this test-case. > > We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > > The challenge here as found out from our discussion here was to mark a > particular mode as preferred so that the Chrome usermode can pick it. > > Now whats happening with that there was always a possibility of two > modes being marked as preferred due to this and so-on. > > We had a pretty long discussion last night and thought of all possible > solutions but all of them look like a hack to us in the driver because > we end up breaking other things due to this. > > So we decided that driver is not the place to handle this test case. > Since we do have IGT support for chromebooks, we will handle both these > test cases there as other vendors do the same way and it works. > > >> Just because Intel DRM has its own solution for something doesn't mean >> everyone else should copy them and implement their own solution. Up >> until recently DP AUX backlights were baked into different DRM >> drivers. A recent effort was made to pull it out. I think the Intel >> DRM code was the "first one" to the party and it wasn't clear how >> things should be broken up to share with other drivers, so mostly it >> did everything itself, but that's not the long term answer. >> >> I'm not saying that we need to block your change on a full re-design >> or anything, but I'm just saying that: >> >> * You're trying to implement a generic DP rule, not something specific >> to Qualcomm hardware. That implies that, if possible, it shouldn't be >> in a Qualcomm driver. >> >> * It doesn't seem like it would be terrible to handle this in the core. >> >> >>> This marks the fail safe mode and IGT test case reads this to set this >>> mode and hence the test passes. >>> >>> We rely on the chromeOS usermode to output pixel data for this test-case >>> and not IGT. We use IGT only for video pattern CTS today but this is a >>> different test-case which is failing. >>> >>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>> or other modes are eliminated. >>> >>> So we have to come up with the right way for the usermode to pick >>> 640x480. >>> >>> We will discuss this a bit more and come up with a different change. >> >> Can you provide the exact EDID from the failing test case? Maybe that >> will help shed some light on what's going on. I looked at the original >> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >> upon HPD Plug Event", but that doesn't give details that seem relevant >> to the discussion here. > > Yes so it is 4.2.2.1 and 4.2.2.6. > > That alone wont give the full picture. > > So its a combination of things. > > While running the test, the test equipment published only one mode. > But we could not support that mode because of 2 lanes. > Equipment did not add 640x480 to the list of modes. > DRM fwk will also not add it because count_modes is not 0 ( there was > one mode ). > So we ended up making these changes. I think a proper solution might be to rewrite drm_helper_probe_single_connector_modes() in the following way: - call get_modes() - validate the result - prune invalid - if the number of modes is 0, call drm_add_override_edid_modes() - validate the result - prune invalid - if the number of modes is still 0, call drm_add_modes_noedid() - validate the result - prune invalid [A separate change might happen here after all the checks: if the number of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o validation. But generally I feel that this shouldn't be necessary because the previous step should have added it.] This way we can be sure that all modes are validated, but still to do our best to add something supported to the list of modes. > > >> >> I guess maybe what's happening is that the test case is giving an EDID >> where all the modes are not supportable by the current clock rate / >> lanes? ...and then somehow we're not falling back to 640x480. It's >> always possible that this is a userspace problem. >> >> In any case, would you object to a revert of the patches in the short >> term? > > Not sure, if you saw this change kuogee posted last night. > https://patchwork.freedesktop.org/patch/483415/ > We did decided to remove all the code related to these test cases and > handle them in IGT. > >> >> -Doug -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:01 ` Dmitry Baryshkov @ 2022-04-26 17:11 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 17:11 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Abhinav Kumar, freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi, On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On 26/04/2022 18:37, Abhinav Kumar wrote: > > Hi Doug > > > > On 4/26/2022 8:20 AM, Doug Anderson wrote: > >> Hi, > >> > >> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar > >> <quic_abhinavk@quicinc.com> wrote: > >>> > >>> On 4/25/2022 7:18 PM, Doug Anderson wrote: > >>>> Hi, > >>>> > >>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar > >>>> <quic_abhinavk@quicinc.com> wrote: > >>>>> > >>>>>>> 2) When there was a valid EDID but no 640x480 mode > >>>>>>> > >>>>>>> This is the equipment specific case and the one even I was a bit > >>>>>>> surprised. There is a DP compliance equipment we have in-house > >>>>>>> and while > >>>>>>> validation, it was found that in its list of modes , it did not > >>>>>>> have any > >>>>>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>>>>> understanding was that, all sinks should have atleast 640x480 but > >>>>>>> apparently this one did not have that. So to handle this DP > >>>>>>> compliance > >>>>>>> equipment behavior, we had to do this. > >>>>>> > >>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>>>>> front of me for testing that only has one mode: > >>>>>> > >>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>>>>> > >>>>> > >>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. > >>>>> Here what is happening is the count was not 0 but 640x480 was not > >>>>> present in the EDID. So we had to add it explicitly. > >>>>> > >>>>> Your tiny display is a display port display? > >>>>> > >>>>> I am referring to only display port monitors. If your tiny display is > >>>>> DP, it should have had 640x480 in its list of modes. > >>>> > >>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP > >>>> (active) adapter. > >>>> > >>>> ...but this is a legal and common thing to have. I suppose possibly my > >>>> HDMI display is "illegal"? > >>>> > >>>> OK, so reading through the spec more carefully, I do see that the DP > >>>> spec makes numerous mentions of the fact that DP sinks _must_ support > >>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > >>>> Timing Format" says that we must support 640x480. It seems like that's > >>>> _intended_ to be used only if the EDID read fails, though or if we > >>>> somehow have to output video without knowledge of the EDID. It seems > >>>> hard to believe that there's a great reason to assume a display will > >>>> support 640x480 if we have more accurate knowledge. > >>>> > >>>> In any case, I guess I would still say that adding this mode belongs > >>>> in the DRM core. The core should notice that it's a DP connection > >>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > >>>> left out and it should add it. We should also make sure it's not > >>>> "preferred" and is last in the list so we never accidentally pick it. > >>>> If DP truly says that we should always give the user 640x480 then > >>>> that's true for everyone, not just Qualcomm. We should add it in the > >>>> core. If, later, someone wants to hide this from the UI it would be > >>>> much easier if they only needed to modify one place. > >>>> > >>> > >>> So I debugged with kuogee just now using the DP compliance equipment. > >>> It turns out, the issue is not that 640x480 mode is not present. > >>> > >>> The issue is that it is not marked as preferred. > >>> > >>> Hence we missed this part during debugging this equipment failure. > >>> > >>> We still have to figure out the best way to either mark 640x480 as > >>> preferred or eliminate other modes during the test-case so that 640x480 > >>> is actually picked by usermode. > >>> > >>> Now that being said, the fix still doesn't belong in the framework. It > >>> has to be in the msm/dp code. > >>> > >>> Different vendors handle this failure case differently looks like. > >>> > >>> Lets take below snippet from i915 as example. > >>> > >>> 3361 if (intel_connector->detect_edid == NULL || > >>> 3362 connector->edid_corrupt || > >>> 3363 intel_dp->aux.i2c_defer_count > 6) { > >>> 3364 /* Check EDID read for NACKs, DEFERs and corruption > >>> 3365 * (DP CTS 1.2 Core r1.1) > >>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > >>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > >>> 3368 * 4.2.2.6 : EDID corruption detected > >>> 3369 * Use failsafe mode for all cases > >>> 3370 */ > >>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || > >>> 3372 intel_dp->aux.i2c_defer_count > 0) > >>> 3373 drm_dbg_kms(&i915->drm, > >>> 3374 "EDID read had %d NACKs, %d > >>> DEFERs\n", > >>> 3375 intel_dp->aux.i2c_nack_count, > >>> 3376 intel_dp->aux.i2c_defer_count); > >>> 3377 intel_dp->compliance.test_data.edid = > >>> INTEL_DP_RESOLUTION_FAILSAFE; > >> > > > > The reason I pointed to this code is to give an example of how other > > drivers handle this test-case. > > > > We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > > > > The challenge here as found out from our discussion here was to mark a > > particular mode as preferred so that the Chrome usermode can pick it. > > > > Now whats happening with that there was always a possibility of two > > modes being marked as preferred due to this and so-on. > > > > We had a pretty long discussion last night and thought of all possible > > solutions but all of them look like a hack to us in the driver because > > we end up breaking other things due to this. > > > > So we decided that driver is not the place to handle this test case. > > Since we do have IGT support for chromebooks, we will handle both these > > test cases there as other vendors do the same way and it works. > > > > > >> Just because Intel DRM has its own solution for something doesn't mean > >> everyone else should copy them and implement their own solution. Up > >> until recently DP AUX backlights were baked into different DRM > >> drivers. A recent effort was made to pull it out. I think the Intel > >> DRM code was the "first one" to the party and it wasn't clear how > >> things should be broken up to share with other drivers, so mostly it > >> did everything itself, but that's not the long term answer. > >> > >> I'm not saying that we need to block your change on a full re-design > >> or anything, but I'm just saying that: > >> > >> * You're trying to implement a generic DP rule, not something specific > >> to Qualcomm hardware. That implies that, if possible, it shouldn't be > >> in a Qualcomm driver. > >> > >> * It doesn't seem like it would be terrible to handle this in the core. > >> > >> > >>> This marks the fail safe mode and IGT test case reads this to set this > >>> mode and hence the test passes. > >>> > >>> We rely on the chromeOS usermode to output pixel data for this test-case > >>> and not IGT. We use IGT only for video pattern CTS today but this is a > >>> different test-case which is failing. > >>> > >>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred > >>> or other modes are eliminated. > >>> > >>> So we have to come up with the right way for the usermode to pick > >>> 640x480. > >>> > >>> We will discuss this a bit more and come up with a different change. > >> > >> Can you provide the exact EDID from the failing test case? Maybe that > >> will help shed some light on what's going on. I looked at the original > >> commit and it just referred to 4.2.2.1, which I assume is "EDID Read > >> upon HPD Plug Event", but that doesn't give details that seem relevant > >> to the discussion here. > > > > Yes so it is 4.2.2.1 and 4.2.2.6. > > > > That alone wont give the full picture. > > > > So its a combination of things. > > > > While running the test, the test equipment published only one mode. > > But we could not support that mode because of 2 lanes. > > Equipment did not add 640x480 to the list of modes. > > DRM fwk will also not add it because count_modes is not 0 ( there was > > one mode ). > > So we ended up making these changes. > > I think a proper solution might be to rewrite > drm_helper_probe_single_connector_modes() in the following way: > - call get_modes() > - validate the result > - prune invalid > > - if the number of modes is 0, call drm_add_override_edid_modes() > - validate the result > - prune invalid > > - if the number of modes is still 0, call drm_add_modes_noedid() > - validate the result > - prune invalid > > [A separate change might happen here after all the checks: if the number > of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o > validation. But generally I feel that this shouldn't be necessary > because the previous step should have added it.] > > This way we can be sure that all modes are validated, but still to do > our best to add something supported to the list of modes. I'm partway through implementing / testing something similar to this. ;-) My logic is slightly different than yours, though. In the very least I'm not convinced that we want to add the higher resolution modes (like 1024x768) if all the modes fail to validate. The DP spec only claims 640x480 is always supported. The higher resolution modes are for when the EDID fails to read I think. Similarly I'm not convinced that we should do pruning before deciding on drm_add_override_edid_modes(). -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 17:11 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 17:11 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, Abhinav Kumar, dri-devel, LKML, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, freedreno Hi, On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On 26/04/2022 18:37, Abhinav Kumar wrote: > > Hi Doug > > > > On 4/26/2022 8:20 AM, Doug Anderson wrote: > >> Hi, > >> > >> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar > >> <quic_abhinavk@quicinc.com> wrote: > >>> > >>> On 4/25/2022 7:18 PM, Doug Anderson wrote: > >>>> Hi, > >>>> > >>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar > >>>> <quic_abhinavk@quicinc.com> wrote: > >>>>> > >>>>>>> 2) When there was a valid EDID but no 640x480 mode > >>>>>>> > >>>>>>> This is the equipment specific case and the one even I was a bit > >>>>>>> surprised. There is a DP compliance equipment we have in-house > >>>>>>> and while > >>>>>>> validation, it was found that in its list of modes , it did not > >>>>>>> have any > >>>>>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>>>>> understanding was that, all sinks should have atleast 640x480 but > >>>>>>> apparently this one did not have that. So to handle this DP > >>>>>>> compliance > >>>>>>> equipment behavior, we had to do this. > >>>>>> > >>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>>>>> front of me for testing that only has one mode: > >>>>>> > >>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>>>>> > >>>>> > >>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. > >>>>> Here what is happening is the count was not 0 but 640x480 was not > >>>>> present in the EDID. So we had to add it explicitly. > >>>>> > >>>>> Your tiny display is a display port display? > >>>>> > >>>>> I am referring to only display port monitors. If your tiny display is > >>>>> DP, it should have had 640x480 in its list of modes. > >>>> > >>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP > >>>> (active) adapter. > >>>> > >>>> ...but this is a legal and common thing to have. I suppose possibly my > >>>> HDMI display is "illegal"? > >>>> > >>>> OK, so reading through the spec more carefully, I do see that the DP > >>>> spec makes numerous mentions of the fact that DP sinks _must_ support > >>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > >>>> Timing Format" says that we must support 640x480. It seems like that's > >>>> _intended_ to be used only if the EDID read fails, though or if we > >>>> somehow have to output video without knowledge of the EDID. It seems > >>>> hard to believe that there's a great reason to assume a display will > >>>> support 640x480 if we have more accurate knowledge. > >>>> > >>>> In any case, I guess I would still say that adding this mode belongs > >>>> in the DRM core. The core should notice that it's a DP connection > >>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > >>>> left out and it should add it. We should also make sure it's not > >>>> "preferred" and is last in the list so we never accidentally pick it. > >>>> If DP truly says that we should always give the user 640x480 then > >>>> that's true for everyone, not just Qualcomm. We should add it in the > >>>> core. If, later, someone wants to hide this from the UI it would be > >>>> much easier if they only needed to modify one place. > >>>> > >>> > >>> So I debugged with kuogee just now using the DP compliance equipment. > >>> It turns out, the issue is not that 640x480 mode is not present. > >>> > >>> The issue is that it is not marked as preferred. > >>> > >>> Hence we missed this part during debugging this equipment failure. > >>> > >>> We still have to figure out the best way to either mark 640x480 as > >>> preferred or eliminate other modes during the test-case so that 640x480 > >>> is actually picked by usermode. > >>> > >>> Now that being said, the fix still doesn't belong in the framework. It > >>> has to be in the msm/dp code. > >>> > >>> Different vendors handle this failure case differently looks like. > >>> > >>> Lets take below snippet from i915 as example. > >>> > >>> 3361 if (intel_connector->detect_edid == NULL || > >>> 3362 connector->edid_corrupt || > >>> 3363 intel_dp->aux.i2c_defer_count > 6) { > >>> 3364 /* Check EDID read for NACKs, DEFERs and corruption > >>> 3365 * (DP CTS 1.2 Core r1.1) > >>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > >>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > >>> 3368 * 4.2.2.6 : EDID corruption detected > >>> 3369 * Use failsafe mode for all cases > >>> 3370 */ > >>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || > >>> 3372 intel_dp->aux.i2c_defer_count > 0) > >>> 3373 drm_dbg_kms(&i915->drm, > >>> 3374 "EDID read had %d NACKs, %d > >>> DEFERs\n", > >>> 3375 intel_dp->aux.i2c_nack_count, > >>> 3376 intel_dp->aux.i2c_defer_count); > >>> 3377 intel_dp->compliance.test_data.edid = > >>> INTEL_DP_RESOLUTION_FAILSAFE; > >> > > > > The reason I pointed to this code is to give an example of how other > > drivers handle this test-case. > > > > We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > > > > The challenge here as found out from our discussion here was to mark a > > particular mode as preferred so that the Chrome usermode can pick it. > > > > Now whats happening with that there was always a possibility of two > > modes being marked as preferred due to this and so-on. > > > > We had a pretty long discussion last night and thought of all possible > > solutions but all of them look like a hack to us in the driver because > > we end up breaking other things due to this. > > > > So we decided that driver is not the place to handle this test case. > > Since we do have IGT support for chromebooks, we will handle both these > > test cases there as other vendors do the same way and it works. > > > > > >> Just because Intel DRM has its own solution for something doesn't mean > >> everyone else should copy them and implement their own solution. Up > >> until recently DP AUX backlights were baked into different DRM > >> drivers. A recent effort was made to pull it out. I think the Intel > >> DRM code was the "first one" to the party and it wasn't clear how > >> things should be broken up to share with other drivers, so mostly it > >> did everything itself, but that's not the long term answer. > >> > >> I'm not saying that we need to block your change on a full re-design > >> or anything, but I'm just saying that: > >> > >> * You're trying to implement a generic DP rule, not something specific > >> to Qualcomm hardware. That implies that, if possible, it shouldn't be > >> in a Qualcomm driver. > >> > >> * It doesn't seem like it would be terrible to handle this in the core. > >> > >> > >>> This marks the fail safe mode and IGT test case reads this to set this > >>> mode and hence the test passes. > >>> > >>> We rely on the chromeOS usermode to output pixel data for this test-case > >>> and not IGT. We use IGT only for video pattern CTS today but this is a > >>> different test-case which is failing. > >>> > >>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred > >>> or other modes are eliminated. > >>> > >>> So we have to come up with the right way for the usermode to pick > >>> 640x480. > >>> > >>> We will discuss this a bit more and come up with a different change. > >> > >> Can you provide the exact EDID from the failing test case? Maybe that > >> will help shed some light on what's going on. I looked at the original > >> commit and it just referred to 4.2.2.1, which I assume is "EDID Read > >> upon HPD Plug Event", but that doesn't give details that seem relevant > >> to the discussion here. > > > > Yes so it is 4.2.2.1 and 4.2.2.6. > > > > That alone wont give the full picture. > > > > So its a combination of things. > > > > While running the test, the test equipment published only one mode. > > But we could not support that mode because of 2 lanes. > > Equipment did not add 640x480 to the list of modes. > > DRM fwk will also not add it because count_modes is not 0 ( there was > > one mode ). > > So we ended up making these changes. > > I think a proper solution might be to rewrite > drm_helper_probe_single_connector_modes() in the following way: > - call get_modes() > - validate the result > - prune invalid > > - if the number of modes is 0, call drm_add_override_edid_modes() > - validate the result > - prune invalid > > - if the number of modes is still 0, call drm_add_modes_noedid() > - validate the result > - prune invalid > > [A separate change might happen here after all the checks: if the number > of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o > validation. But generally I feel that this shouldn't be necessary > because the previous step should have added it.] > > This way we can be sure that all modes are validated, but still to do > our best to add something supported to the list of modes. I'm partway through implementing / testing something similar to this. ;-) My logic is slightly different than yours, though. In the very least I'm not convinced that we want to add the higher resolution modes (like 1024x768) if all the modes fail to validate. The DP spec only claims 640x480 is always supported. The higher resolution modes are for when the EDID fails to read I think. Similarly I'm not convinced that we should do pruning before deciding on drm_add_override_edid_modes(). -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:11 ` Doug Anderson @ 2022-04-26 17:24 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 17:24 UTC (permalink / raw) To: Doug Anderson, Dmitry Baryshkov Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul On 4/26/2022 10:11 AM, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 18:37, Abhinav Kumar wrote: >>> Hi Doug >>> >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>> >>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>> and while >>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>> have any >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>> compliance >>>>>>>>> equipment behavior, we had to do this. >>>>>>>> >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>> front of me for testing that only has one mode: >>>>>>>> >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>> >>>>>>> >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>> >>>>>>> Your tiny display is a display port display? >>>>>>> >>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>> >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>> (active) adapter. >>>>>> >>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>> HDMI display is "illegal"? >>>>>> >>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>> hard to believe that there's a great reason to assume a display will >>>>>> support 640x480 if we have more accurate knowledge. >>>>>> >>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>> left out and it should add it. We should also make sure it's not >>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>> If DP truly says that we should always give the user 640x480 then >>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>> much easier if they only needed to modify one place. >>>>>> >>>>> >>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>> >>>>> The issue is that it is not marked as preferred. >>>>> >>>>> Hence we missed this part during debugging this equipment failure. >>>>> >>>>> We still have to figure out the best way to either mark 640x480 as >>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>> is actually picked by usermode. >>>>> >>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>> has to be in the msm/dp code. >>>>> >>>>> Different vendors handle this failure case differently looks like. >>>>> >>>>> Lets take below snippet from i915 as example. >>>>> >>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>> 3362 connector->edid_corrupt || >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>> 3369 * Use failsafe mode for all cases >>>>> 3370 */ >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>> 3373 drm_dbg_kms(&i915->drm, >>>>> 3374 "EDID read had %d NACKs, %d >>>>> DEFERs\n", >>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>> 3377 intel_dp->compliance.test_data.edid = >>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>> >>> >>> The reason I pointed to this code is to give an example of how other >>> drivers handle this test-case. >>> >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>> >>> The challenge here as found out from our discussion here was to mark a >>> particular mode as preferred so that the Chrome usermode can pick it. >>> >>> Now whats happening with that there was always a possibility of two >>> modes being marked as preferred due to this and so-on. >>> >>> We had a pretty long discussion last night and thought of all possible >>> solutions but all of them look like a hack to us in the driver because >>> we end up breaking other things due to this. >>> >>> So we decided that driver is not the place to handle this test case. >>> Since we do have IGT support for chromebooks, we will handle both these >>> test cases there as other vendors do the same way and it works. >>> >>> >>>> Just because Intel DRM has its own solution for something doesn't mean >>>> everyone else should copy them and implement their own solution. Up >>>> until recently DP AUX backlights were baked into different DRM >>>> drivers. A recent effort was made to pull it out. I think the Intel >>>> DRM code was the "first one" to the party and it wasn't clear how >>>> things should be broken up to share with other drivers, so mostly it >>>> did everything itself, but that's not the long term answer. >>>> >>>> I'm not saying that we need to block your change on a full re-design >>>> or anything, but I'm just saying that: >>>> >>>> * You're trying to implement a generic DP rule, not something specific >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>> in a Qualcomm driver. >>>> >>>> * It doesn't seem like it would be terrible to handle this in the core. >>>> >>>> >>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>> mode and hence the test passes. >>>>> >>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>> different test-case which is failing. >>>>> >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>> or other modes are eliminated. >>>>> >>>>> So we have to come up with the right way for the usermode to pick >>>>> 640x480. >>>>> >>>>> We will discuss this a bit more and come up with a different change. >>>> >>>> Can you provide the exact EDID from the failing test case? Maybe that >>>> will help shed some light on what's going on. I looked at the original >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>> to the discussion here. >>> >>> Yes so it is 4.2.2.1 and 4.2.2.6. >>> >>> That alone wont give the full picture. >>> >>> So its a combination of things. >>> >>> While running the test, the test equipment published only one mode. >>> But we could not support that mode because of 2 lanes. >>> Equipment did not add 640x480 to the list of modes. >>> DRM fwk will also not add it because count_modes is not 0 ( there was >>> one mode ). >>> So we ended up making these changes. >> >> I think a proper solution might be to rewrite >> drm_helper_probe_single_connector_modes() in the following way: >> - call get_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is 0, call drm_add_override_edid_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is still 0, call drm_add_modes_noedid() >> - validate the result >> - prune invalid >> >> [A separate change might happen here after all the checks: if the number >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >> validation. But generally I feel that this shouldn't be necessary >> because the previous step should have added it.] >> >> This way we can be sure that all modes are validated, but still to do >> our best to add something supported to the list of modes. > > I'm partway through implementing / testing something similar to this. > ;-) My logic is slightly different than yours, though. In the very > least I'm not convinced that we want to add the higher resolution > modes (like 1024x768) if all the modes fail to validate. The DP spec > only claims 640x480 is always supported. The higher resolution modes > are for when the EDID fails to read I think. Similarly I'm not > convinced that we should do pruning before deciding on > drm_add_override_edid_modes(). Doug, we will certainly evaluate it once you post it. Thanks Abhinav > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 17:24 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 17:24 UTC (permalink / raw) To: Doug Anderson, Dmitry Baryshkov Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno On 4/26/2022 10:11 AM, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 18:37, Abhinav Kumar wrote: >>> Hi Doug >>> >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>> >>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>> and while >>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>> have any >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>> compliance >>>>>>>>> equipment behavior, we had to do this. >>>>>>>> >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>> front of me for testing that only has one mode: >>>>>>>> >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>> >>>>>>> >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>> >>>>>>> Your tiny display is a display port display? >>>>>>> >>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>> >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>> (active) adapter. >>>>>> >>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>> HDMI display is "illegal"? >>>>>> >>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>> hard to believe that there's a great reason to assume a display will >>>>>> support 640x480 if we have more accurate knowledge. >>>>>> >>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>> left out and it should add it. We should also make sure it's not >>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>> If DP truly says that we should always give the user 640x480 then >>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>> much easier if they only needed to modify one place. >>>>>> >>>>> >>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>> >>>>> The issue is that it is not marked as preferred. >>>>> >>>>> Hence we missed this part during debugging this equipment failure. >>>>> >>>>> We still have to figure out the best way to either mark 640x480 as >>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>> is actually picked by usermode. >>>>> >>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>> has to be in the msm/dp code. >>>>> >>>>> Different vendors handle this failure case differently looks like. >>>>> >>>>> Lets take below snippet from i915 as example. >>>>> >>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>> 3362 connector->edid_corrupt || >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>> 3369 * Use failsafe mode for all cases >>>>> 3370 */ >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>> 3373 drm_dbg_kms(&i915->drm, >>>>> 3374 "EDID read had %d NACKs, %d >>>>> DEFERs\n", >>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>> 3377 intel_dp->compliance.test_data.edid = >>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>> >>> >>> The reason I pointed to this code is to give an example of how other >>> drivers handle this test-case. >>> >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>> >>> The challenge here as found out from our discussion here was to mark a >>> particular mode as preferred so that the Chrome usermode can pick it. >>> >>> Now whats happening with that there was always a possibility of two >>> modes being marked as preferred due to this and so-on. >>> >>> We had a pretty long discussion last night and thought of all possible >>> solutions but all of them look like a hack to us in the driver because >>> we end up breaking other things due to this. >>> >>> So we decided that driver is not the place to handle this test case. >>> Since we do have IGT support for chromebooks, we will handle both these >>> test cases there as other vendors do the same way and it works. >>> >>> >>>> Just because Intel DRM has its own solution for something doesn't mean >>>> everyone else should copy them and implement their own solution. Up >>>> until recently DP AUX backlights were baked into different DRM >>>> drivers. A recent effort was made to pull it out. I think the Intel >>>> DRM code was the "first one" to the party and it wasn't clear how >>>> things should be broken up to share with other drivers, so mostly it >>>> did everything itself, but that's not the long term answer. >>>> >>>> I'm not saying that we need to block your change on a full re-design >>>> or anything, but I'm just saying that: >>>> >>>> * You're trying to implement a generic DP rule, not something specific >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>> in a Qualcomm driver. >>>> >>>> * It doesn't seem like it would be terrible to handle this in the core. >>>> >>>> >>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>> mode and hence the test passes. >>>>> >>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>> different test-case which is failing. >>>>> >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>> or other modes are eliminated. >>>>> >>>>> So we have to come up with the right way for the usermode to pick >>>>> 640x480. >>>>> >>>>> We will discuss this a bit more and come up with a different change. >>>> >>>> Can you provide the exact EDID from the failing test case? Maybe that >>>> will help shed some light on what's going on. I looked at the original >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>> to the discussion here. >>> >>> Yes so it is 4.2.2.1 and 4.2.2.6. >>> >>> That alone wont give the full picture. >>> >>> So its a combination of things. >>> >>> While running the test, the test equipment published only one mode. >>> But we could not support that mode because of 2 lanes. >>> Equipment did not add 640x480 to the list of modes. >>> DRM fwk will also not add it because count_modes is not 0 ( there was >>> one mode ). >>> So we ended up making these changes. >> >> I think a proper solution might be to rewrite >> drm_helper_probe_single_connector_modes() in the following way: >> - call get_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is 0, call drm_add_override_edid_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is still 0, call drm_add_modes_noedid() >> - validate the result >> - prune invalid >> >> [A separate change might happen here after all the checks: if the number >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >> validation. But generally I feel that this shouldn't be necessary >> because the previous step should have added it.] >> >> This way we can be sure that all modes are validated, but still to do >> our best to add something supported to the list of modes. > > I'm partway through implementing / testing something similar to this. > ;-) My logic is slightly different than yours, though. In the very > least I'm not convinced that we want to add the higher resolution > modes (like 1024x768) if all the modes fail to validate. The DP spec > only claims 640x480 is always supported. The higher resolution modes > are for when the EDID fails to read I think. Similarly I'm not > convinced that we should do pruning before deciding on > drm_add_override_edid_modes(). Doug, we will certainly evaluate it once you post it. Thanks Abhinav > > -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:11 ` Doug Anderson @ 2022-04-26 17:44 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 17:44 UTC (permalink / raw) To: Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, Abhinav Kumar, dri-devel, LKML, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, freedreno On 26/04/2022 20:11, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 18:37, Abhinav Kumar wrote: >>> Hi Doug >>> >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>> >>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>> and while >>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>> have any >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>> compliance >>>>>>>>> equipment behavior, we had to do this. >>>>>>>> >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>> front of me for testing that only has one mode: >>>>>>>> >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>> >>>>>>> >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>> >>>>>>> Your tiny display is a display port display? >>>>>>> >>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>> >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>> (active) adapter. >>>>>> >>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>> HDMI display is "illegal"? >>>>>> >>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>> hard to believe that there's a great reason to assume a display will >>>>>> support 640x480 if we have more accurate knowledge. >>>>>> >>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>> left out and it should add it. We should also make sure it's not >>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>> If DP truly says that we should always give the user 640x480 then >>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>> much easier if they only needed to modify one place. >>>>>> >>>>> >>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>> >>>>> The issue is that it is not marked as preferred. >>>>> >>>>> Hence we missed this part during debugging this equipment failure. >>>>> >>>>> We still have to figure out the best way to either mark 640x480 as >>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>> is actually picked by usermode. >>>>> >>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>> has to be in the msm/dp code. >>>>> >>>>> Different vendors handle this failure case differently looks like. >>>>> >>>>> Lets take below snippet from i915 as example. >>>>> >>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>> 3362 connector->edid_corrupt || >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>> 3369 * Use failsafe mode for all cases >>>>> 3370 */ >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>> 3373 drm_dbg_kms(&i915->drm, >>>>> 3374 "EDID read had %d NACKs, %d >>>>> DEFERs\n", >>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>> 3377 intel_dp->compliance.test_data.edid = >>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>> >>> >>> The reason I pointed to this code is to give an example of how other >>> drivers handle this test-case. >>> >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>> >>> The challenge here as found out from our discussion here was to mark a >>> particular mode as preferred so that the Chrome usermode can pick it. >>> >>> Now whats happening with that there was always a possibility of two >>> modes being marked as preferred due to this and so-on. >>> >>> We had a pretty long discussion last night and thought of all possible >>> solutions but all of them look like a hack to us in the driver because >>> we end up breaking other things due to this. >>> >>> So we decided that driver is not the place to handle this test case. >>> Since we do have IGT support for chromebooks, we will handle both these >>> test cases there as other vendors do the same way and it works. >>> >>> >>>> Just because Intel DRM has its own solution for something doesn't mean >>>> everyone else should copy them and implement their own solution. Up >>>> until recently DP AUX backlights were baked into different DRM >>>> drivers. A recent effort was made to pull it out. I think the Intel >>>> DRM code was the "first one" to the party and it wasn't clear how >>>> things should be broken up to share with other drivers, so mostly it >>>> did everything itself, but that's not the long term answer. >>>> >>>> I'm not saying that we need to block your change on a full re-design >>>> or anything, but I'm just saying that: >>>> >>>> * You're trying to implement a generic DP rule, not something specific >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>> in a Qualcomm driver. >>>> >>>> * It doesn't seem like it would be terrible to handle this in the core. >>>> >>>> >>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>> mode and hence the test passes. >>>>> >>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>> different test-case which is failing. >>>>> >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>> or other modes are eliminated. >>>>> >>>>> So we have to come up with the right way for the usermode to pick >>>>> 640x480. >>>>> >>>>> We will discuss this a bit more and come up with a different change. >>>> >>>> Can you provide the exact EDID from the failing test case? Maybe that >>>> will help shed some light on what's going on. I looked at the original >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>> to the discussion here. >>> >>> Yes so it is 4.2.2.1 and 4.2.2.6. >>> >>> That alone wont give the full picture. >>> >>> So its a combination of things. >>> >>> While running the test, the test equipment published only one mode. >>> But we could not support that mode because of 2 lanes. >>> Equipment did not add 640x480 to the list of modes. >>> DRM fwk will also not add it because count_modes is not 0 ( there was >>> one mode ). >>> So we ended up making these changes. >> >> I think a proper solution might be to rewrite >> drm_helper_probe_single_connector_modes() in the following way: >> - call get_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is 0, call drm_add_override_edid_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is still 0, call drm_add_modes_noedid() >> - validate the result >> - prune invalid >> >> [A separate change might happen here after all the checks: if the number >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >> validation. But generally I feel that this shouldn't be necessary >> because the previous step should have added it.] >> >> This way we can be sure that all modes are validated, but still to do >> our best to add something supported to the list of modes. > > I'm partway through implementing / testing something similar to this. > ;-) My logic is slightly different than yours, though. In the very > least I'm not convinced that we want to add the higher resolution > modes (like 1024x768) if all the modes fail to validate. The DP spec > only claims 640x480 is always supported. The higher resolution modes > are for when the EDID fails to read I think. Similarly I'm not > convinced that we should do pruning before deciding on > drm_add_override_edid_modes(). I think pruning before drm_add_override_edid_modes() would allow one to use override if the first read returned some modes which are invalid. Regarding 1024 vs 640. For the restructure we shouldn't change this. And I'd actually point to the following commit message: commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 Author: Adam Jackson <ajax@redhat.com> Date: Mon Nov 23 14:23:07 2009 -0500 drm/modes: Fall back to 1024x768 instead of 800x600 This matches the X server's fallback modes when using RANDR 1.2. See also: http://bugzilla.redhat.com/538761 Signed-off-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> So I'd say, let's leave 1024 as is and just try them if all other modes are invalid. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 17:44 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 17:44 UTC (permalink / raw) To: Doug Anderson Cc: Abhinav Kumar, freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul On 26/04/2022 20:11, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 18:37, Abhinav Kumar wrote: >>> Hi Doug >>> >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>> Hi, >>>> >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>> <quic_abhinavk@quicinc.com> wrote: >>>>> >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>> >>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>> and while >>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>> have any >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>> compliance >>>>>>>>> equipment behavior, we had to do this. >>>>>>>> >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>> front of me for testing that only has one mode: >>>>>>>> >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>> >>>>>>> >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>> >>>>>>> Your tiny display is a display port display? >>>>>>> >>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>> >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>> (active) adapter. >>>>>> >>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>> HDMI display is "illegal"? >>>>>> >>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>> hard to believe that there's a great reason to assume a display will >>>>>> support 640x480 if we have more accurate knowledge. >>>>>> >>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>> left out and it should add it. We should also make sure it's not >>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>> If DP truly says that we should always give the user 640x480 then >>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>> much easier if they only needed to modify one place. >>>>>> >>>>> >>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>> >>>>> The issue is that it is not marked as preferred. >>>>> >>>>> Hence we missed this part during debugging this equipment failure. >>>>> >>>>> We still have to figure out the best way to either mark 640x480 as >>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>> is actually picked by usermode. >>>>> >>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>> has to be in the msm/dp code. >>>>> >>>>> Different vendors handle this failure case differently looks like. >>>>> >>>>> Lets take below snippet from i915 as example. >>>>> >>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>> 3362 connector->edid_corrupt || >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>> 3369 * Use failsafe mode for all cases >>>>> 3370 */ >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>> 3373 drm_dbg_kms(&i915->drm, >>>>> 3374 "EDID read had %d NACKs, %d >>>>> DEFERs\n", >>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>> 3377 intel_dp->compliance.test_data.edid = >>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>> >>> >>> The reason I pointed to this code is to give an example of how other >>> drivers handle this test-case. >>> >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>> >>> The challenge here as found out from our discussion here was to mark a >>> particular mode as preferred so that the Chrome usermode can pick it. >>> >>> Now whats happening with that there was always a possibility of two >>> modes being marked as preferred due to this and so-on. >>> >>> We had a pretty long discussion last night and thought of all possible >>> solutions but all of them look like a hack to us in the driver because >>> we end up breaking other things due to this. >>> >>> So we decided that driver is not the place to handle this test case. >>> Since we do have IGT support for chromebooks, we will handle both these >>> test cases there as other vendors do the same way and it works. >>> >>> >>>> Just because Intel DRM has its own solution for something doesn't mean >>>> everyone else should copy them and implement their own solution. Up >>>> until recently DP AUX backlights were baked into different DRM >>>> drivers. A recent effort was made to pull it out. I think the Intel >>>> DRM code was the "first one" to the party and it wasn't clear how >>>> things should be broken up to share with other drivers, so mostly it >>>> did everything itself, but that's not the long term answer. >>>> >>>> I'm not saying that we need to block your change on a full re-design >>>> or anything, but I'm just saying that: >>>> >>>> * You're trying to implement a generic DP rule, not something specific >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>> in a Qualcomm driver. >>>> >>>> * It doesn't seem like it would be terrible to handle this in the core. >>>> >>>> >>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>> mode and hence the test passes. >>>>> >>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>> different test-case which is failing. >>>>> >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>> or other modes are eliminated. >>>>> >>>>> So we have to come up with the right way for the usermode to pick >>>>> 640x480. >>>>> >>>>> We will discuss this a bit more and come up with a different change. >>>> >>>> Can you provide the exact EDID from the failing test case? Maybe that >>>> will help shed some light on what's going on. I looked at the original >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>> to the discussion here. >>> >>> Yes so it is 4.2.2.1 and 4.2.2.6. >>> >>> That alone wont give the full picture. >>> >>> So its a combination of things. >>> >>> While running the test, the test equipment published only one mode. >>> But we could not support that mode because of 2 lanes. >>> Equipment did not add 640x480 to the list of modes. >>> DRM fwk will also not add it because count_modes is not 0 ( there was >>> one mode ). >>> So we ended up making these changes. >> >> I think a proper solution might be to rewrite >> drm_helper_probe_single_connector_modes() in the following way: >> - call get_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is 0, call drm_add_override_edid_modes() >> - validate the result >> - prune invalid >> >> - if the number of modes is still 0, call drm_add_modes_noedid() >> - validate the result >> - prune invalid >> >> [A separate change might happen here after all the checks: if the number >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >> validation. But generally I feel that this shouldn't be necessary >> because the previous step should have added it.] >> >> This way we can be sure that all modes are validated, but still to do >> our best to add something supported to the list of modes. > > I'm partway through implementing / testing something similar to this. > ;-) My logic is slightly different than yours, though. In the very > least I'm not convinced that we want to add the higher resolution > modes (like 1024x768) if all the modes fail to validate. The DP spec > only claims 640x480 is always supported. The higher resolution modes > are for when the EDID fails to read I think. Similarly I'm not > convinced that we should do pruning before deciding on > drm_add_override_edid_modes(). I think pruning before drm_add_override_edid_modes() would allow one to use override if the first read returned some modes which are invalid. Regarding 1024 vs 640. For the restructure we shouldn't change this. And I'd actually point to the following commit message: commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 Author: Adam Jackson <ajax@redhat.com> Date: Mon Nov 23 14:23:07 2009 -0500 drm/modes: Fall back to 1024x768 instead of 800x600 This matches the X server's fallback modes when using RANDR 1.2. See also: http://bugzilla.redhat.com/538761 Signed-off-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> So I'd say, let's leave 1024 as is and just try them if all other modes are invalid. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:44 ` Dmitry Baryshkov @ 2022-04-26 17:56 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 17:56 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Abhinav Kumar, freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi, On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On 26/04/2022 20:11, Doug Anderson wrote: > > Hi, > > > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > > <dmitry.baryshkov@linaro.org> wrote: > >> > >> On 26/04/2022 18:37, Abhinav Kumar wrote: > >>> Hi Doug > >>> > >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: > >>>> Hi, > >>>> > >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar > >>>> <quic_abhinavk@quicinc.com> wrote: > >>>>> > >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: > >>>>>> Hi, > >>>>>> > >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar > >>>>>> <quic_abhinavk@quicinc.com> wrote: > >>>>>>> > >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode > >>>>>>>>> > >>>>>>>>> This is the equipment specific case and the one even I was a bit > >>>>>>>>> surprised. There is a DP compliance equipment we have in-house > >>>>>>>>> and while > >>>>>>>>> validation, it was found that in its list of modes , it did not > >>>>>>>>> have any > >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but > >>>>>>>>> apparently this one did not have that. So to handle this DP > >>>>>>>>> compliance > >>>>>>>>> equipment behavior, we had to do this. > >>>>>>>> > >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>>>>>>> front of me for testing that only has one mode: > >>>>>>>> > >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>>>>>>> > >>>>>>> > >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. > >>>>>>> Here what is happening is the count was not 0 but 640x480 was not > >>>>>>> present in the EDID. So we had to add it explicitly. > >>>>>>> > >>>>>>> Your tiny display is a display port display? > >>>>>>> > >>>>>>> I am referring to only display port monitors. If your tiny display is > >>>>>>> DP, it should have had 640x480 in its list of modes. > >>>>>> > >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP > >>>>>> (active) adapter. > >>>>>> > >>>>>> ...but this is a legal and common thing to have. I suppose possibly my > >>>>>> HDMI display is "illegal"? > >>>>>> > >>>>>> OK, so reading through the spec more carefully, I do see that the DP > >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support > >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > >>>>>> Timing Format" says that we must support 640x480. It seems like that's > >>>>>> _intended_ to be used only if the EDID read fails, though or if we > >>>>>> somehow have to output video without knowledge of the EDID. It seems > >>>>>> hard to believe that there's a great reason to assume a display will > >>>>>> support 640x480 if we have more accurate knowledge. > >>>>>> > >>>>>> In any case, I guess I would still say that adding this mode belongs > >>>>>> in the DRM core. The core should notice that it's a DP connection > >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > >>>>>> left out and it should add it. We should also make sure it's not > >>>>>> "preferred" and is last in the list so we never accidentally pick it. > >>>>>> If DP truly says that we should always give the user 640x480 then > >>>>>> that's true for everyone, not just Qualcomm. We should add it in the > >>>>>> core. If, later, someone wants to hide this from the UI it would be > >>>>>> much easier if they only needed to modify one place. > >>>>>> > >>>>> > >>>>> So I debugged with kuogee just now using the DP compliance equipment. > >>>>> It turns out, the issue is not that 640x480 mode is not present. > >>>>> > >>>>> The issue is that it is not marked as preferred. > >>>>> > >>>>> Hence we missed this part during debugging this equipment failure. > >>>>> > >>>>> We still have to figure out the best way to either mark 640x480 as > >>>>> preferred or eliminate other modes during the test-case so that 640x480 > >>>>> is actually picked by usermode. > >>>>> > >>>>> Now that being said, the fix still doesn't belong in the framework. It > >>>>> has to be in the msm/dp code. > >>>>> > >>>>> Different vendors handle this failure case differently looks like. > >>>>> > >>>>> Lets take below snippet from i915 as example. > >>>>> > >>>>> 3361 if (intel_connector->detect_edid == NULL || > >>>>> 3362 connector->edid_corrupt || > >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { > >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption > >>>>> 3365 * (DP CTS 1.2 Core r1.1) > >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > >>>>> 3368 * 4.2.2.6 : EDID corruption detected > >>>>> 3369 * Use failsafe mode for all cases > >>>>> 3370 */ > >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || > >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) > >>>>> 3373 drm_dbg_kms(&i915->drm, > >>>>> 3374 "EDID read had %d NACKs, %d > >>>>> DEFERs\n", > >>>>> 3375 intel_dp->aux.i2c_nack_count, > >>>>> 3376 intel_dp->aux.i2c_defer_count); > >>>>> 3377 intel_dp->compliance.test_data.edid = > >>>>> INTEL_DP_RESOLUTION_FAILSAFE; > >>>> > >>> > >>> The reason I pointed to this code is to give an example of how other > >>> drivers handle this test-case. > >>> > >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > >>> > >>> The challenge here as found out from our discussion here was to mark a > >>> particular mode as preferred so that the Chrome usermode can pick it. > >>> > >>> Now whats happening with that there was always a possibility of two > >>> modes being marked as preferred due to this and so-on. > >>> > >>> We had a pretty long discussion last night and thought of all possible > >>> solutions but all of them look like a hack to us in the driver because > >>> we end up breaking other things due to this. > >>> > >>> So we decided that driver is not the place to handle this test case. > >>> Since we do have IGT support for chromebooks, we will handle both these > >>> test cases there as other vendors do the same way and it works. > >>> > >>> > >>>> Just because Intel DRM has its own solution for something doesn't mean > >>>> everyone else should copy them and implement their own solution. Up > >>>> until recently DP AUX backlights were baked into different DRM > >>>> drivers. A recent effort was made to pull it out. I think the Intel > >>>> DRM code was the "first one" to the party and it wasn't clear how > >>>> things should be broken up to share with other drivers, so mostly it > >>>> did everything itself, but that's not the long term answer. > >>>> > >>>> I'm not saying that we need to block your change on a full re-design > >>>> or anything, but I'm just saying that: > >>>> > >>>> * You're trying to implement a generic DP rule, not something specific > >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be > >>>> in a Qualcomm driver. > >>>> > >>>> * It doesn't seem like it would be terrible to handle this in the core. > >>>> > >>>> > >>>>> This marks the fail safe mode and IGT test case reads this to set this > >>>>> mode and hence the test passes. > >>>>> > >>>>> We rely on the chromeOS usermode to output pixel data for this test-case > >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a > >>>>> different test-case which is failing. > >>>>> > >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred > >>>>> or other modes are eliminated. > >>>>> > >>>>> So we have to come up with the right way for the usermode to pick > >>>>> 640x480. > >>>>> > >>>>> We will discuss this a bit more and come up with a different change. > >>>> > >>>> Can you provide the exact EDID from the failing test case? Maybe that > >>>> will help shed some light on what's going on. I looked at the original > >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read > >>>> upon HPD Plug Event", but that doesn't give details that seem relevant > >>>> to the discussion here. > >>> > >>> Yes so it is 4.2.2.1 and 4.2.2.6. > >>> > >>> That alone wont give the full picture. > >>> > >>> So its a combination of things. > >>> > >>> While running the test, the test equipment published only one mode. > >>> But we could not support that mode because of 2 lanes. > >>> Equipment did not add 640x480 to the list of modes. > >>> DRM fwk will also not add it because count_modes is not 0 ( there was > >>> one mode ). > >>> So we ended up making these changes. > >> > >> I think a proper solution might be to rewrite > >> drm_helper_probe_single_connector_modes() in the following way: > >> - call get_modes() > >> - validate the result > >> - prune invalid > >> > >> - if the number of modes is 0, call drm_add_override_edid_modes() > >> - validate the result > >> - prune invalid > >> > >> - if the number of modes is still 0, call drm_add_modes_noedid() > >> - validate the result > >> - prune invalid > >> > >> [A separate change might happen here after all the checks: if the number > >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o > >> validation. But generally I feel that this shouldn't be necessary > >> because the previous step should have added it.] > >> > >> This way we can be sure that all modes are validated, but still to do > >> our best to add something supported to the list of modes. > > > > I'm partway through implementing / testing something similar to this. > > ;-) My logic is slightly different than yours, though. In the very > > least I'm not convinced that we want to add the higher resolution > > modes (like 1024x768) if all the modes fail to validate. The DP spec > > only claims 640x480 is always supported. The higher resolution modes > > are for when the EDID fails to read I think. Similarly I'm not > > convinced that we should do pruning before deciding on > > drm_add_override_edid_modes(). > > > I think pruning before drm_add_override_edid_modes() would allow one to > use override if the first read returned some modes which are invalid. Yeah, I'm less certain about drm_add_override_edid_modes(), but as per documented it's only to be used if the EDID failed to read. If someone has an actual use case where they need to add the override modes for this specific case then we can, but I think it can be done separately once someone has an actual use case. > Regarding 1024 vs 640. For the restructure we shouldn't change this. And > I'd actually point to the following commit message: > > commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 > Author: Adam Jackson <ajax@redhat.com> > Date: Mon Nov 23 14:23:07 2009 -0500 > > drm/modes: Fall back to 1024x768 instead of 800x600 > > This matches the X server's fallback modes when using RANDR 1.2. > > See also: http://bugzilla.redhat.com/538761 > > Signed-off-by: Adam Jackson <ajax@redhat.com> > Signed-off-by: Dave Airlie <airlied@redhat.com> > > > So I'd say, let's leave 1024 as is and just try them if all other modes > are invalid. I'm pretty strongly against adding 1024x768 when all modes fail to validate. Specifically: If the EDID fully fails to read then adding these higher resolution modes makes sense. We have no knowledge at all about the display in this case and so we can guess that some standard higher resolutions might make sense. In the case we're dealing with here, we have very specific knowledge about what the display said it could handle and we can't support any of them. The DP spec _only_ lists 640x480 as a required mode so that's the only one we should add. -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 17:56 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 17:56 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, Abhinav Kumar, dri-devel, LKML, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, freedreno Hi, On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On 26/04/2022 20:11, Doug Anderson wrote: > > Hi, > > > > On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov > > <dmitry.baryshkov@linaro.org> wrote: > >> > >> On 26/04/2022 18:37, Abhinav Kumar wrote: > >>> Hi Doug > >>> > >>> On 4/26/2022 8:20 AM, Doug Anderson wrote: > >>>> Hi, > >>>> > >>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar > >>>> <quic_abhinavk@quicinc.com> wrote: > >>>>> > >>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: > >>>>>> Hi, > >>>>>> > >>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar > >>>>>> <quic_abhinavk@quicinc.com> wrote: > >>>>>>> > >>>>>>>>> 2) When there was a valid EDID but no 640x480 mode > >>>>>>>>> > >>>>>>>>> This is the equipment specific case and the one even I was a bit > >>>>>>>>> surprised. There is a DP compliance equipment we have in-house > >>>>>>>>> and while > >>>>>>>>> validation, it was found that in its list of modes , it did not > >>>>>>>>> have any > >>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my > >>>>>>>>> understanding was that, all sinks should have atleast 640x480 but > >>>>>>>>> apparently this one did not have that. So to handle this DP > >>>>>>>>> compliance > >>>>>>>>> equipment behavior, we had to do this. > >>>>>>>> > >>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID > >>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding > >>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in > >>>>>>>> front of me for testing that only has one mode: > >>>>>>>> > >>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 > >>>>>>>> > >>>>>>> > >>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. > >>>>>>> Here what is happening is the count was not 0 but 640x480 was not > >>>>>>> present in the EDID. So we had to add it explicitly. > >>>>>>> > >>>>>>> Your tiny display is a display port display? > >>>>>>> > >>>>>>> I am referring to only display port monitors. If your tiny display is > >>>>>>> DP, it should have had 640x480 in its list of modes. > >>>>>> > >>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP > >>>>>> (active) adapter. > >>>>>> > >>>>>> ...but this is a legal and common thing to have. I suppose possibly my > >>>>>> HDMI display is "illegal"? > >>>>>> > >>>>>> OK, so reading through the spec more carefully, I do see that the DP > >>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support > >>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video > >>>>>> Timing Format" says that we must support 640x480. It seems like that's > >>>>>> _intended_ to be used only if the EDID read fails, though or if we > >>>>>> somehow have to output video without knowledge of the EDID. It seems > >>>>>> hard to believe that there's a great reason to assume a display will > >>>>>> support 640x480 if we have more accurate knowledge. > >>>>>> > >>>>>> In any case, I guess I would still say that adding this mode belongs > >>>>>> in the DRM core. The core should notice that it's a DP connection > >>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was > >>>>>> left out and it should add it. We should also make sure it's not > >>>>>> "preferred" and is last in the list so we never accidentally pick it. > >>>>>> If DP truly says that we should always give the user 640x480 then > >>>>>> that's true for everyone, not just Qualcomm. We should add it in the > >>>>>> core. If, later, someone wants to hide this from the UI it would be > >>>>>> much easier if they only needed to modify one place. > >>>>>> > >>>>> > >>>>> So I debugged with kuogee just now using the DP compliance equipment. > >>>>> It turns out, the issue is not that 640x480 mode is not present. > >>>>> > >>>>> The issue is that it is not marked as preferred. > >>>>> > >>>>> Hence we missed this part during debugging this equipment failure. > >>>>> > >>>>> We still have to figure out the best way to either mark 640x480 as > >>>>> preferred or eliminate other modes during the test-case so that 640x480 > >>>>> is actually picked by usermode. > >>>>> > >>>>> Now that being said, the fix still doesn't belong in the framework. It > >>>>> has to be in the msm/dp code. > >>>>> > >>>>> Different vendors handle this failure case differently looks like. > >>>>> > >>>>> Lets take below snippet from i915 as example. > >>>>> > >>>>> 3361 if (intel_connector->detect_edid == NULL || > >>>>> 3362 connector->edid_corrupt || > >>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { > >>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption > >>>>> 3365 * (DP CTS 1.2 Core r1.1) > >>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK > >>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER > >>>>> 3368 * 4.2.2.6 : EDID corruption detected > >>>>> 3369 * Use failsafe mode for all cases > >>>>> 3370 */ > >>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || > >>>>> 3372 intel_dp->aux.i2c_defer_count > 0) > >>>>> 3373 drm_dbg_kms(&i915->drm, > >>>>> 3374 "EDID read had %d NACKs, %d > >>>>> DEFERs\n", > >>>>> 3375 intel_dp->aux.i2c_nack_count, > >>>>> 3376 intel_dp->aux.i2c_defer_count); > >>>>> 3377 intel_dp->compliance.test_data.edid = > >>>>> INTEL_DP_RESOLUTION_FAILSAFE; > >>>> > >>> > >>> The reason I pointed to this code is to give an example of how other > >>> drivers handle this test-case. > >>> > >>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. > >>> > >>> The challenge here as found out from our discussion here was to mark a > >>> particular mode as preferred so that the Chrome usermode can pick it. > >>> > >>> Now whats happening with that there was always a possibility of two > >>> modes being marked as preferred due to this and so-on. > >>> > >>> We had a pretty long discussion last night and thought of all possible > >>> solutions but all of them look like a hack to us in the driver because > >>> we end up breaking other things due to this. > >>> > >>> So we decided that driver is not the place to handle this test case. > >>> Since we do have IGT support for chromebooks, we will handle both these > >>> test cases there as other vendors do the same way and it works. > >>> > >>> > >>>> Just because Intel DRM has its own solution for something doesn't mean > >>>> everyone else should copy them and implement their own solution. Up > >>>> until recently DP AUX backlights were baked into different DRM > >>>> drivers. A recent effort was made to pull it out. I think the Intel > >>>> DRM code was the "first one" to the party and it wasn't clear how > >>>> things should be broken up to share with other drivers, so mostly it > >>>> did everything itself, but that's not the long term answer. > >>>> > >>>> I'm not saying that we need to block your change on a full re-design > >>>> or anything, but I'm just saying that: > >>>> > >>>> * You're trying to implement a generic DP rule, not something specific > >>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be > >>>> in a Qualcomm driver. > >>>> > >>>> * It doesn't seem like it would be terrible to handle this in the core. > >>>> > >>>> > >>>>> This marks the fail safe mode and IGT test case reads this to set this > >>>>> mode and hence the test passes. > >>>>> > >>>>> We rely on the chromeOS usermode to output pixel data for this test-case > >>>>> and not IGT. We use IGT only for video pattern CTS today but this is a > >>>>> different test-case which is failing. > >>>>> > >>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred > >>>>> or other modes are eliminated. > >>>>> > >>>>> So we have to come up with the right way for the usermode to pick > >>>>> 640x480. > >>>>> > >>>>> We will discuss this a bit more and come up with a different change. > >>>> > >>>> Can you provide the exact EDID from the failing test case? Maybe that > >>>> will help shed some light on what's going on. I looked at the original > >>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read > >>>> upon HPD Plug Event", but that doesn't give details that seem relevant > >>>> to the discussion here. > >>> > >>> Yes so it is 4.2.2.1 and 4.2.2.6. > >>> > >>> That alone wont give the full picture. > >>> > >>> So its a combination of things. > >>> > >>> While running the test, the test equipment published only one mode. > >>> But we could not support that mode because of 2 lanes. > >>> Equipment did not add 640x480 to the list of modes. > >>> DRM fwk will also not add it because count_modes is not 0 ( there was > >>> one mode ). > >>> So we ended up making these changes. > >> > >> I think a proper solution might be to rewrite > >> drm_helper_probe_single_connector_modes() in the following way: > >> - call get_modes() > >> - validate the result > >> - prune invalid > >> > >> - if the number of modes is 0, call drm_add_override_edid_modes() > >> - validate the result > >> - prune invalid > >> > >> - if the number of modes is still 0, call drm_add_modes_noedid() > >> - validate the result > >> - prune invalid > >> > >> [A separate change might happen here after all the checks: if the number > >> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o > >> validation. But generally I feel that this shouldn't be necessary > >> because the previous step should have added it.] > >> > >> This way we can be sure that all modes are validated, but still to do > >> our best to add something supported to the list of modes. > > > > I'm partway through implementing / testing something similar to this. > > ;-) My logic is slightly different than yours, though. In the very > > least I'm not convinced that we want to add the higher resolution > > modes (like 1024x768) if all the modes fail to validate. The DP spec > > only claims 640x480 is always supported. The higher resolution modes > > are for when the EDID fails to read I think. Similarly I'm not > > convinced that we should do pruning before deciding on > > drm_add_override_edid_modes(). > > > I think pruning before drm_add_override_edid_modes() would allow one to > use override if the first read returned some modes which are invalid. Yeah, I'm less certain about drm_add_override_edid_modes(), but as per documented it's only to be used if the EDID failed to read. If someone has an actual use case where they need to add the override modes for this specific case then we can, but I think it can be done separately once someone has an actual use case. > Regarding 1024 vs 640. For the restructure we shouldn't change this. And > I'd actually point to the following commit message: > > commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 > Author: Adam Jackson <ajax@redhat.com> > Date: Mon Nov 23 14:23:07 2009 -0500 > > drm/modes: Fall back to 1024x768 instead of 800x600 > > This matches the X server's fallback modes when using RANDR 1.2. > > See also: http://bugzilla.redhat.com/538761 > > Signed-off-by: Adam Jackson <ajax@redhat.com> > Signed-off-by: Dave Airlie <airlied@redhat.com> > > > So I'd say, let's leave 1024 as is and just try them if all other modes > are invalid. I'm pretty strongly against adding 1024x768 when all modes fail to validate. Specifically: If the EDID fully fails to read then adding these higher resolution modes makes sense. We have no knowledge at all about the display in this case and so we can guess that some standard higher resolutions might make sense. In the case we're dealing with here, we have very specific knowledge about what the display said it could handle and we can't support any of them. The DP spec _only_ lists 640x480 as a required mode so that's the only one we should add. -Doug ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:56 ` Doug Anderson @ 2022-04-26 18:03 ` Abhinav Kumar -1 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 18:03 UTC (permalink / raw) To: Doug Anderson, Dmitry Baryshkov Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, dri-devel, LKML, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, freedreno On 4/26/2022 10:56 AM, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 20:11, Doug Anderson wrote: >>> Hi, >>> >>> On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov >>> <dmitry.baryshkov@linaro.org> wrote: >>>> >>>> On 26/04/2022 18:37, Abhinav Kumar wrote: >>>>> Hi Doug >>>>> >>>>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>>>> Hi, >>>>>>>> >>>>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>>>> >>>>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>>>> >>>>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>>>> and while >>>>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>>>> have any >>>>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>>>> compliance >>>>>>>>>>> equipment behavior, we had to do this. >>>>>>>>>> >>>>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>>>> front of me for testing that only has one mode: >>>>>>>>>> >>>>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>>>> >>>>>>>>> >>>>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>>>> >>>>>>>>> Your tiny display is a display port display? >>>>>>>>> >>>>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>>>> >>>>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>>>> (active) adapter. >>>>>>>> >>>>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>>>> HDMI display is "illegal"? >>>>>>>> >>>>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>>>> hard to believe that there's a great reason to assume a display will >>>>>>>> support 640x480 if we have more accurate knowledge. >>>>>>>> >>>>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>>>> left out and it should add it. We should also make sure it's not >>>>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>>>> If DP truly says that we should always give the user 640x480 then >>>>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>>>> much easier if they only needed to modify one place. >>>>>>>> >>>>>>> >>>>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>>>> >>>>>>> The issue is that it is not marked as preferred. >>>>>>> >>>>>>> Hence we missed this part during debugging this equipment failure. >>>>>>> >>>>>>> We still have to figure out the best way to either mark 640x480 as >>>>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>>>> is actually picked by usermode. >>>>>>> >>>>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>>>> has to be in the msm/dp code. >>>>>>> >>>>>>> Different vendors handle this failure case differently looks like. >>>>>>> >>>>>>> Lets take below snippet from i915 as example. >>>>>>> >>>>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>>>> 3362 connector->edid_corrupt || >>>>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>>>> 3369 * Use failsafe mode for all cases >>>>>>> 3370 */ >>>>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>>>> 3373 drm_dbg_kms(&i915->drm, >>>>>>> 3374 "EDID read had %d NACKs, %d >>>>>>> DEFERs\n", >>>>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>>>> 3377 intel_dp->compliance.test_data.edid = >>>>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>>>> >>>>> >>>>> The reason I pointed to this code is to give an example of how other >>>>> drivers handle this test-case. >>>>> >>>>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>>>> >>>>> The challenge here as found out from our discussion here was to mark a >>>>> particular mode as preferred so that the Chrome usermode can pick it. >>>>> >>>>> Now whats happening with that there was always a possibility of two >>>>> modes being marked as preferred due to this and so-on. >>>>> >>>>> We had a pretty long discussion last night and thought of all possible >>>>> solutions but all of them look like a hack to us in the driver because >>>>> we end up breaking other things due to this. >>>>> >>>>> So we decided that driver is not the place to handle this test case. >>>>> Since we do have IGT support for chromebooks, we will handle both these >>>>> test cases there as other vendors do the same way and it works. >>>>> >>>>> >>>>>> Just because Intel DRM has its own solution for something doesn't mean >>>>>> everyone else should copy them and implement their own solution. Up >>>>>> until recently DP AUX backlights were baked into different DRM >>>>>> drivers. A recent effort was made to pull it out. I think the Intel >>>>>> DRM code was the "first one" to the party and it wasn't clear how >>>>>> things should be broken up to share with other drivers, so mostly it >>>>>> did everything itself, but that's not the long term answer. >>>>>> >>>>>> I'm not saying that we need to block your change on a full re-design >>>>>> or anything, but I'm just saying that: >>>>>> >>>>>> * You're trying to implement a generic DP rule, not something specific >>>>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>>>> in a Qualcomm driver. >>>>>> >>>>>> * It doesn't seem like it would be terrible to handle this in the core. >>>>>> >>>>>> >>>>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>>>> mode and hence the test passes. >>>>>>> >>>>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>>>> different test-case which is failing. >>>>>>> >>>>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>>>> or other modes are eliminated. >>>>>>> >>>>>>> So we have to come up with the right way for the usermode to pick >>>>>>> 640x480. >>>>>>> >>>>>>> We will discuss this a bit more and come up with a different change. >>>>>> >>>>>> Can you provide the exact EDID from the failing test case? Maybe that >>>>>> will help shed some light on what's going on. I looked at the original >>>>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>>>> to the discussion here. >>>>> >>>>> Yes so it is 4.2.2.1 and 4.2.2.6. >>>>> >>>>> That alone wont give the full picture. >>>>> >>>>> So its a combination of things. >>>>> >>>>> While running the test, the test equipment published only one mode. >>>>> But we could not support that mode because of 2 lanes. >>>>> Equipment did not add 640x480 to the list of modes. >>>>> DRM fwk will also not add it because count_modes is not 0 ( there was >>>>> one mode ). >>>>> So we ended up making these changes. >>>> >>>> I think a proper solution might be to rewrite >>>> drm_helper_probe_single_connector_modes() in the following way: >>>> - call get_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is 0, call drm_add_override_edid_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is still 0, call drm_add_modes_noedid() >>>> - validate the result >>>> - prune invalid >>>> >>>> [A separate change might happen here after all the checks: if the number >>>> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >>>> validation. But generally I feel that this shouldn't be necessary >>>> because the previous step should have added it.] >>>> >>>> This way we can be sure that all modes are validated, but still to do >>>> our best to add something supported to the list of modes. >>> >>> I'm partway through implementing / testing something similar to this. >>> ;-) My logic is slightly different than yours, though. In the very >>> least I'm not convinced that we want to add the higher resolution >>> modes (like 1024x768) if all the modes fail to validate. The DP spec >>> only claims 640x480 is always supported. The higher resolution modes >>> are for when the EDID fails to read I think. Similarly I'm not >>> convinced that we should do pruning before deciding on >>> drm_add_override_edid_modes(). >> >> >> I think pruning before drm_add_override_edid_modes() would allow one to >> use override if the first read returned some modes which are invalid. > > Yeah, I'm less certain about drm_add_override_edid_modes(), but as per > documented it's only to be used if the EDID failed to read. > > If someone has an actual use case where they need to add the override > modes for this specific case then we can, but I think it can be done > separately once someone has an actual use case. > > >> Regarding 1024 vs 640. For the restructure we shouldn't change this. And >> I'd actually point to the following commit message: >> >> commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 >> Author: Adam Jackson <ajax@redhat.com> >> Date: Mon Nov 23 14:23:07 2009 -0500 >> >> drm/modes: Fall back to 1024x768 instead of 800x600 >> >> This matches the X server's fallback modes when using RANDR 1.2. >> >> See also: http://bugzilla.redhat.com/538761 >> >> Signed-off-by: Adam Jackson <ajax@redhat.com> >> Signed-off-by: Dave Airlie <airlied@redhat.com> >> >> >> So I'd say, let's leave 1024 as is and just try them if all other modes >> are invalid. > > I'm pretty strongly against adding 1024x768 when all modes fail to > validate. Specifically: > > If the EDID fully fails to read then adding these higher resolution > modes makes sense. We have no knowledge at all about the display in > this case and so we can guess that some standard higher resolutions > might make sense. In the case we're dealing with here, we have very > specific knowledge about what the display said it could handle and we > can't support any of them. The DP spec _only_ lists 640x480 as a > required mode so that's the only one we should add. > > -Doug So one thing to note Doug, in case you have not already made note of it. I believe you are referring to drm_add_modes_noedid() and NOT drm_add_override_edid_modes()? Because the latter needs an override firware If so, just wanted to mention that drm_add_modes_noedid() operates on the probed_modes() list but after validation and pruning, probed_modes list does not exits. It gets copied over to connector->modes list. So we cannot directly call that. ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 18:03 ` Abhinav Kumar 0 siblings, 0 replies; 42+ messages in thread From: Abhinav Kumar @ 2022-04-26 18:03 UTC (permalink / raw) To: Doug Anderson, Dmitry Baryshkov Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, Kuogee Hsieh, LKML, dri-devel, Stephen Boyd, Vinod Koul, Andy Gross, Aravind Venkateswaran (QUIC), Bjorn Andersson, Sean Paul On 4/26/2022 10:56 AM, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 20:11, Doug Anderson wrote: >>> Hi, >>> >>> On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov >>> <dmitry.baryshkov@linaro.org> wrote: >>>> >>>> On 26/04/2022 18:37, Abhinav Kumar wrote: >>>>> Hi Doug >>>>> >>>>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>>>> Hi, >>>>>>>> >>>>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>>>> >>>>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>>>> >>>>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>>>> and while >>>>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>>>> have any >>>>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>>>> compliance >>>>>>>>>>> equipment behavior, we had to do this. >>>>>>>>>> >>>>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>>>> front of me for testing that only has one mode: >>>>>>>>>> >>>>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>>>> >>>>>>>>> >>>>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>>>> >>>>>>>>> Your tiny display is a display port display? >>>>>>>>> >>>>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>>>> >>>>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>>>> (active) adapter. >>>>>>>> >>>>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>>>> HDMI display is "illegal"? >>>>>>>> >>>>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>>>> hard to believe that there's a great reason to assume a display will >>>>>>>> support 640x480 if we have more accurate knowledge. >>>>>>>> >>>>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>>>> left out and it should add it. We should also make sure it's not >>>>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>>>> If DP truly says that we should always give the user 640x480 then >>>>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>>>> much easier if they only needed to modify one place. >>>>>>>> >>>>>>> >>>>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>>>> >>>>>>> The issue is that it is not marked as preferred. >>>>>>> >>>>>>> Hence we missed this part during debugging this equipment failure. >>>>>>> >>>>>>> We still have to figure out the best way to either mark 640x480 as >>>>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>>>> is actually picked by usermode. >>>>>>> >>>>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>>>> has to be in the msm/dp code. >>>>>>> >>>>>>> Different vendors handle this failure case differently looks like. >>>>>>> >>>>>>> Lets take below snippet from i915 as example. >>>>>>> >>>>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>>>> 3362 connector->edid_corrupt || >>>>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>>>> 3369 * Use failsafe mode for all cases >>>>>>> 3370 */ >>>>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>>>> 3373 drm_dbg_kms(&i915->drm, >>>>>>> 3374 "EDID read had %d NACKs, %d >>>>>>> DEFERs\n", >>>>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>>>> 3377 intel_dp->compliance.test_data.edid = >>>>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>>>> >>>>> >>>>> The reason I pointed to this code is to give an example of how other >>>>> drivers handle this test-case. >>>>> >>>>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>>>> >>>>> The challenge here as found out from our discussion here was to mark a >>>>> particular mode as preferred so that the Chrome usermode can pick it. >>>>> >>>>> Now whats happening with that there was always a possibility of two >>>>> modes being marked as preferred due to this and so-on. >>>>> >>>>> We had a pretty long discussion last night and thought of all possible >>>>> solutions but all of them look like a hack to us in the driver because >>>>> we end up breaking other things due to this. >>>>> >>>>> So we decided that driver is not the place to handle this test case. >>>>> Since we do have IGT support for chromebooks, we will handle both these >>>>> test cases there as other vendors do the same way and it works. >>>>> >>>>> >>>>>> Just because Intel DRM has its own solution for something doesn't mean >>>>>> everyone else should copy them and implement their own solution. Up >>>>>> until recently DP AUX backlights were baked into different DRM >>>>>> drivers. A recent effort was made to pull it out. I think the Intel >>>>>> DRM code was the "first one" to the party and it wasn't clear how >>>>>> things should be broken up to share with other drivers, so mostly it >>>>>> did everything itself, but that's not the long term answer. >>>>>> >>>>>> I'm not saying that we need to block your change on a full re-design >>>>>> or anything, but I'm just saying that: >>>>>> >>>>>> * You're trying to implement a generic DP rule, not something specific >>>>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>>>> in a Qualcomm driver. >>>>>> >>>>>> * It doesn't seem like it would be terrible to handle this in the core. >>>>>> >>>>>> >>>>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>>>> mode and hence the test passes. >>>>>>> >>>>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>>>> different test-case which is failing. >>>>>>> >>>>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>>>> or other modes are eliminated. >>>>>>> >>>>>>> So we have to come up with the right way for the usermode to pick >>>>>>> 640x480. >>>>>>> >>>>>>> We will discuss this a bit more and come up with a different change. >>>>>> >>>>>> Can you provide the exact EDID from the failing test case? Maybe that >>>>>> will help shed some light on what's going on. I looked at the original >>>>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>>>> to the discussion here. >>>>> >>>>> Yes so it is 4.2.2.1 and 4.2.2.6. >>>>> >>>>> That alone wont give the full picture. >>>>> >>>>> So its a combination of things. >>>>> >>>>> While running the test, the test equipment published only one mode. >>>>> But we could not support that mode because of 2 lanes. >>>>> Equipment did not add 640x480 to the list of modes. >>>>> DRM fwk will also not add it because count_modes is not 0 ( there was >>>>> one mode ). >>>>> So we ended up making these changes. >>>> >>>> I think a proper solution might be to rewrite >>>> drm_helper_probe_single_connector_modes() in the following way: >>>> - call get_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is 0, call drm_add_override_edid_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is still 0, call drm_add_modes_noedid() >>>> - validate the result >>>> - prune invalid >>>> >>>> [A separate change might happen here after all the checks: if the number >>>> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >>>> validation. But generally I feel that this shouldn't be necessary >>>> because the previous step should have added it.] >>>> >>>> This way we can be sure that all modes are validated, but still to do >>>> our best to add something supported to the list of modes. >>> >>> I'm partway through implementing / testing something similar to this. >>> ;-) My logic is slightly different than yours, though. In the very >>> least I'm not convinced that we want to add the higher resolution >>> modes (like 1024x768) if all the modes fail to validate. The DP spec >>> only claims 640x480 is always supported. The higher resolution modes >>> are for when the EDID fails to read I think. Similarly I'm not >>> convinced that we should do pruning before deciding on >>> drm_add_override_edid_modes(). >> >> >> I think pruning before drm_add_override_edid_modes() would allow one to >> use override if the first read returned some modes which are invalid. > > Yeah, I'm less certain about drm_add_override_edid_modes(), but as per > documented it's only to be used if the EDID failed to read. > > If someone has an actual use case where they need to add the override > modes for this specific case then we can, but I think it can be done > separately once someone has an actual use case. > > >> Regarding 1024 vs 640. For the restructure we shouldn't change this. And >> I'd actually point to the following commit message: >> >> commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 >> Author: Adam Jackson <ajax@redhat.com> >> Date: Mon Nov 23 14:23:07 2009 -0500 >> >> drm/modes: Fall back to 1024x768 instead of 800x600 >> >> This matches the X server's fallback modes when using RANDR 1.2. >> >> See also: http://bugzilla.redhat.com/538761 >> >> Signed-off-by: Adam Jackson <ajax@redhat.com> >> Signed-off-by: Dave Airlie <airlied@redhat.com> >> >> >> So I'd say, let's leave 1024 as is and just try them if all other modes >> are invalid. > > I'm pretty strongly against adding 1024x768 when all modes fail to > validate. Specifically: > > If the EDID fully fails to read then adding these higher resolution > modes makes sense. We have no knowledge at all about the display in > this case and so we can guess that some standard higher resolutions > might make sense. In the case we're dealing with here, we have very > specific knowledge about what the display said it could handle and we > can't support any of them. The DP spec _only_ lists 640x480 as a > required mode so that's the only one we should add. > > -Doug So one thing to note Doug, in case you have not already made note of it. I believe you are referring to drm_add_modes_noedid() and NOT drm_add_override_edid_modes()? Because the latter needs an override firware If so, just wanted to mention that drm_add_modes_noedid() operates on the probed_modes() list but after validation and pruning, probed_modes list does not exits. It gets copied over to connector->modes list. So we cannot directly call that. ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 17:56 ` Doug Anderson @ 2022-04-26 18:04 ` Dmitry Baryshkov -1 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 18:04 UTC (permalink / raw) To: Doug Anderson Cc: Abhinav Kumar, freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul On 26/04/2022 20:56, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 20:11, Doug Anderson wrote: >>> Hi, >>> >>> On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov >>> <dmitry.baryshkov@linaro.org> wrote: >>>> >>>> On 26/04/2022 18:37, Abhinav Kumar wrote: >>>>> Hi Doug >>>>> >>>>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>>>> Hi, >>>>>>>> >>>>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>>>> >>>>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>>>> >>>>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>>>> and while >>>>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>>>> have any >>>>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>>>> compliance >>>>>>>>>>> equipment behavior, we had to do this. >>>>>>>>>> >>>>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>>>> front of me for testing that only has one mode: >>>>>>>>>> >>>>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>>>> >>>>>>>>> >>>>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>>>> >>>>>>>>> Your tiny display is a display port display? >>>>>>>>> >>>>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>>>> >>>>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>>>> (active) adapter. >>>>>>>> >>>>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>>>> HDMI display is "illegal"? >>>>>>>> >>>>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>>>> hard to believe that there's a great reason to assume a display will >>>>>>>> support 640x480 if we have more accurate knowledge. >>>>>>>> >>>>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>>>> left out and it should add it. We should also make sure it's not >>>>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>>>> If DP truly says that we should always give the user 640x480 then >>>>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>>>> much easier if they only needed to modify one place. >>>>>>>> >>>>>>> >>>>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>>>> >>>>>>> The issue is that it is not marked as preferred. >>>>>>> >>>>>>> Hence we missed this part during debugging this equipment failure. >>>>>>> >>>>>>> We still have to figure out the best way to either mark 640x480 as >>>>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>>>> is actually picked by usermode. >>>>>>> >>>>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>>>> has to be in the msm/dp code. >>>>>>> >>>>>>> Different vendors handle this failure case differently looks like. >>>>>>> >>>>>>> Lets take below snippet from i915 as example. >>>>>>> >>>>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>>>> 3362 connector->edid_corrupt || >>>>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>>>> 3369 * Use failsafe mode for all cases >>>>>>> 3370 */ >>>>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>>>> 3373 drm_dbg_kms(&i915->drm, >>>>>>> 3374 "EDID read had %d NACKs, %d >>>>>>> DEFERs\n", >>>>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>>>> 3377 intel_dp->compliance.test_data.edid = >>>>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>>>> >>>>> >>>>> The reason I pointed to this code is to give an example of how other >>>>> drivers handle this test-case. >>>>> >>>>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>>>> >>>>> The challenge here as found out from our discussion here was to mark a >>>>> particular mode as preferred so that the Chrome usermode can pick it. >>>>> >>>>> Now whats happening with that there was always a possibility of two >>>>> modes being marked as preferred due to this and so-on. >>>>> >>>>> We had a pretty long discussion last night and thought of all possible >>>>> solutions but all of them look like a hack to us in the driver because >>>>> we end up breaking other things due to this. >>>>> >>>>> So we decided that driver is not the place to handle this test case. >>>>> Since we do have IGT support for chromebooks, we will handle both these >>>>> test cases there as other vendors do the same way and it works. >>>>> >>>>> >>>>>> Just because Intel DRM has its own solution for something doesn't mean >>>>>> everyone else should copy them and implement their own solution. Up >>>>>> until recently DP AUX backlights were baked into different DRM >>>>>> drivers. A recent effort was made to pull it out. I think the Intel >>>>>> DRM code was the "first one" to the party and it wasn't clear how >>>>>> things should be broken up to share with other drivers, so mostly it >>>>>> did everything itself, but that's not the long term answer. >>>>>> >>>>>> I'm not saying that we need to block your change on a full re-design >>>>>> or anything, but I'm just saying that: >>>>>> >>>>>> * You're trying to implement a generic DP rule, not something specific >>>>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>>>> in a Qualcomm driver. >>>>>> >>>>>> * It doesn't seem like it would be terrible to handle this in the core. >>>>>> >>>>>> >>>>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>>>> mode and hence the test passes. >>>>>>> >>>>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>>>> different test-case which is failing. >>>>>>> >>>>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>>>> or other modes are eliminated. >>>>>>> >>>>>>> So we have to come up with the right way for the usermode to pick >>>>>>> 640x480. >>>>>>> >>>>>>> We will discuss this a bit more and come up with a different change. >>>>>> >>>>>> Can you provide the exact EDID from the failing test case? Maybe that >>>>>> will help shed some light on what's going on. I looked at the original >>>>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>>>> to the discussion here. >>>>> >>>>> Yes so it is 4.2.2.1 and 4.2.2.6. >>>>> >>>>> That alone wont give the full picture. >>>>> >>>>> So its a combination of things. >>>>> >>>>> While running the test, the test equipment published only one mode. >>>>> But we could not support that mode because of 2 lanes. >>>>> Equipment did not add 640x480 to the list of modes. >>>>> DRM fwk will also not add it because count_modes is not 0 ( there was >>>>> one mode ). >>>>> So we ended up making these changes. >>>> >>>> I think a proper solution might be to rewrite >>>> drm_helper_probe_single_connector_modes() in the following way: >>>> - call get_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is 0, call drm_add_override_edid_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is still 0, call drm_add_modes_noedid() >>>> - validate the result >>>> - prune invalid >>>> >>>> [A separate change might happen here after all the checks: if the number >>>> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >>>> validation. But generally I feel that this shouldn't be necessary >>>> because the previous step should have added it.] >>>> >>>> This way we can be sure that all modes are validated, but still to do >>>> our best to add something supported to the list of modes. >>> >>> I'm partway through implementing / testing something similar to this. >>> ;-) My logic is slightly different than yours, though. In the very >>> least I'm not convinced that we want to add the higher resolution >>> modes (like 1024x768) if all the modes fail to validate. The DP spec >>> only claims 640x480 is always supported. The higher resolution modes >>> are for when the EDID fails to read I think. Similarly I'm not >>> convinced that we should do pruning before deciding on >>> drm_add_override_edid_modes(). >> >> >> I think pruning before drm_add_override_edid_modes() would allow one to >> use override if the first read returned some modes which are invalid. > > Yeah, I'm less certain about drm_add_override_edid_modes(), but as per > documented it's only to be used if the EDID failed to read. > > If someone has an actual use case where they need to add the override > modes for this specific case then we can, but I think it can be done > separately once someone has an actual use case. > > >> Regarding 1024 vs 640. For the restructure we shouldn't change this. And >> I'd actually point to the following commit message: >> >> commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 >> Author: Adam Jackson <ajax@redhat.com> >> Date: Mon Nov 23 14:23:07 2009 -0500 >> >> drm/modes: Fall back to 1024x768 instead of 800x600 >> >> This matches the X server's fallback modes when using RANDR 1.2. >> >> See also: http://bugzilla.redhat.com/538761 >> >> Signed-off-by: Adam Jackson <ajax@redhat.com> >> Signed-off-by: Dave Airlie <airlied@redhat.com> >> >> >> So I'd say, let's leave 1024 as is and just try them if all other modes >> are invalid. > > I'm pretty strongly against adding 1024x768 when all modes fail to > validate. Specifically: > > If the EDID fully fails to read then adding these higher resolution > modes makes sense. We have no knowledge at all about the display in > this case and so we can guess that some standard higher resolutions > might make sense. In the case we're dealing with here, we have very > specific knowledge about what the display said it could handle and we > can't support any of them. The DP spec _only_ lists 640x480 as a > required mode so that's the only one we should add. Then this should be a DP-specific override happening after all the pruning. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 18:04 ` Dmitry Baryshkov 0 siblings, 0 replies; 42+ messages in thread From: Dmitry Baryshkov @ 2022-04-26 18:04 UTC (permalink / raw) To: Doug Anderson Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, Abhinav Kumar, dri-devel, LKML, Vinod Koul, Andy Gross, Bjorn Andersson, Aravind Venkateswaran (QUIC), Kuogee Hsieh, freedreno On 26/04/2022 20:56, Doug Anderson wrote: > Hi, > > On Tue, Apr 26, 2022 at 10:44 AM Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: >> >> On 26/04/2022 20:11, Doug Anderson wrote: >>> Hi, >>> >>> On Tue, Apr 26, 2022 at 10:01 AM Dmitry Baryshkov >>> <dmitry.baryshkov@linaro.org> wrote: >>>> >>>> On 26/04/2022 18:37, Abhinav Kumar wrote: >>>>> Hi Doug >>>>> >>>>> On 4/26/2022 8:20 AM, Doug Anderson wrote: >>>>>> Hi, >>>>>> >>>>>> On Mon, Apr 25, 2022 at 8:35 PM Abhinav Kumar >>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>> >>>>>>> On 4/25/2022 7:18 PM, Doug Anderson wrote: >>>>>>>> Hi, >>>>>>>> >>>>>>>> On Mon, Apr 25, 2022 at 6:42 PM Abhinav Kumar >>>>>>>> <quic_abhinavk@quicinc.com> wrote: >>>>>>>>> >>>>>>>>>>> 2) When there was a valid EDID but no 640x480 mode >>>>>>>>>>> >>>>>>>>>>> This is the equipment specific case and the one even I was a bit >>>>>>>>>>> surprised. There is a DP compliance equipment we have in-house >>>>>>>>>>> and while >>>>>>>>>>> validation, it was found that in its list of modes , it did not >>>>>>>>>>> have any >>>>>>>>>>> modes which chromebook supported ( due to 2 lanes ). But my >>>>>>>>>>> understanding was that, all sinks should have atleast 640x480 but >>>>>>>>>>> apparently this one did not have that. So to handle this DP >>>>>>>>>>> compliance >>>>>>>>>>> equipment behavior, we had to do this. >>>>>>>>>> >>>>>>>>>> That doesn't seem right. If there's a valid EDID and the valid EDID >>>>>>>>>> doesn't contain 640x480, are you _sure_ you're supposed to be adding >>>>>>>>>> 640x480? That doesn't sound right to me. I've got a tiny display in >>>>>>>>>> front of me for testing that only has one mode: >>>>>>>>>> >>>>>>>>>> #0 800x480 65.68 800 840 888 928 480 493 496 525 32000 >>>>>>>>>> >>>>>>>>> >>>>>>>>> As I had wrote, DRM core kicks in only when the count of modes is 0. >>>>>>>>> Here what is happening is the count was not 0 but 640x480 was not >>>>>>>>> present in the EDID. So we had to add it explicitly. >>>>>>>>> >>>>>>>>> Your tiny display is a display port display? >>>>>>>>> >>>>>>>>> I am referring to only display port monitors. If your tiny display is >>>>>>>>> DP, it should have had 640x480 in its list of modes. >>>>>>>> >>>>>>>> My tiny display is actually a HDMI display hooked up to a HDMI to DP >>>>>>>> (active) adapter. >>>>>>>> >>>>>>>> ...but this is a legal and common thing to have. I suppose possibly my >>>>>>>> HDMI display is "illegal"? >>>>>>>> >>>>>>>> OK, so reading through the spec more carefully, I do see that the DP >>>>>>>> spec makes numerous mentions of the fact that DP sinks _must_ support >>>>>>>> 640x480. Even going back to DP 1.4, I see section "5.2.1.2 Video >>>>>>>> Timing Format" says that we must support 640x480. It seems like that's >>>>>>>> _intended_ to be used only if the EDID read fails, though or if we >>>>>>>> somehow have to output video without knowledge of the EDID. It seems >>>>>>>> hard to believe that there's a great reason to assume a display will >>>>>>>> support 640x480 if we have more accurate knowledge. >>>>>>>> >>>>>>>> In any case, I guess I would still say that adding this mode belongs >>>>>>>> in the DRM core. The core should notice that it's a DP connection >>>>>>>> (bridge->type == DRM_MODE_CONNECTOR_DisplayPort) and that 640x480 was >>>>>>>> left out and it should add it. We should also make sure it's not >>>>>>>> "preferred" and is last in the list so we never accidentally pick it. >>>>>>>> If DP truly says that we should always give the user 640x480 then >>>>>>>> that's true for everyone, not just Qualcomm. We should add it in the >>>>>>>> core. If, later, someone wants to hide this from the UI it would be >>>>>>>> much easier if they only needed to modify one place. >>>>>>>> >>>>>>> >>>>>>> So I debugged with kuogee just now using the DP compliance equipment. >>>>>>> It turns out, the issue is not that 640x480 mode is not present. >>>>>>> >>>>>>> The issue is that it is not marked as preferred. >>>>>>> >>>>>>> Hence we missed this part during debugging this equipment failure. >>>>>>> >>>>>>> We still have to figure out the best way to either mark 640x480 as >>>>>>> preferred or eliminate other modes during the test-case so that 640x480 >>>>>>> is actually picked by usermode. >>>>>>> >>>>>>> Now that being said, the fix still doesn't belong in the framework. It >>>>>>> has to be in the msm/dp code. >>>>>>> >>>>>>> Different vendors handle this failure case differently looks like. >>>>>>> >>>>>>> Lets take below snippet from i915 as example. >>>>>>> >>>>>>> 3361 if (intel_connector->detect_edid == NULL || >>>>>>> 3362 connector->edid_corrupt || >>>>>>> 3363 intel_dp->aux.i2c_defer_count > 6) { >>>>>>> 3364 /* Check EDID read for NACKs, DEFERs and corruption >>>>>>> 3365 * (DP CTS 1.2 Core r1.1) >>>>>>> 3366 * 4.2.2.4 : Failed EDID read, I2C_NAK >>>>>>> 3367 * 4.2.2.5 : Failed EDID read, I2C_DEFER >>>>>>> 3368 * 4.2.2.6 : EDID corruption detected >>>>>>> 3369 * Use failsafe mode for all cases >>>>>>> 3370 */ >>>>>>> 3371 if (intel_dp->aux.i2c_nack_count > 0 || >>>>>>> 3372 intel_dp->aux.i2c_defer_count > 0) >>>>>>> 3373 drm_dbg_kms(&i915->drm, >>>>>>> 3374 "EDID read had %d NACKs, %d >>>>>>> DEFERs\n", >>>>>>> 3375 intel_dp->aux.i2c_nack_count, >>>>>>> 3376 intel_dp->aux.i2c_defer_count); >>>>>>> 3377 intel_dp->compliance.test_data.edid = >>>>>>> INTEL_DP_RESOLUTION_FAILSAFE; >>>>>> >>>>> >>>>> The reason I pointed to this code is to give an example of how other >>>>> drivers handle this test-case. >>>>> >>>>> We added this patch for 4.2.2.1 and 4.2.2.6 EDID test cases. >>>>> >>>>> The challenge here as found out from our discussion here was to mark a >>>>> particular mode as preferred so that the Chrome usermode can pick it. >>>>> >>>>> Now whats happening with that there was always a possibility of two >>>>> modes being marked as preferred due to this and so-on. >>>>> >>>>> We had a pretty long discussion last night and thought of all possible >>>>> solutions but all of them look like a hack to us in the driver because >>>>> we end up breaking other things due to this. >>>>> >>>>> So we decided that driver is not the place to handle this test case. >>>>> Since we do have IGT support for chromebooks, we will handle both these >>>>> test cases there as other vendors do the same way and it works. >>>>> >>>>> >>>>>> Just because Intel DRM has its own solution for something doesn't mean >>>>>> everyone else should copy them and implement their own solution. Up >>>>>> until recently DP AUX backlights were baked into different DRM >>>>>> drivers. A recent effort was made to pull it out. I think the Intel >>>>>> DRM code was the "first one" to the party and it wasn't clear how >>>>>> things should be broken up to share with other drivers, so mostly it >>>>>> did everything itself, but that's not the long term answer. >>>>>> >>>>>> I'm not saying that we need to block your change on a full re-design >>>>>> or anything, but I'm just saying that: >>>>>> >>>>>> * You're trying to implement a generic DP rule, not something specific >>>>>> to Qualcomm hardware. That implies that, if possible, it shouldn't be >>>>>> in a Qualcomm driver. >>>>>> >>>>>> * It doesn't seem like it would be terrible to handle this in the core. >>>>>> >>>>>> >>>>>>> This marks the fail safe mode and IGT test case reads this to set this >>>>>>> mode and hence the test passes. >>>>>>> >>>>>>> We rely on the chromeOS usermode to output pixel data for this test-case >>>>>>> and not IGT. We use IGT only for video pattern CTS today but this is a >>>>>>> different test-case which is failing. >>>>>>> >>>>>>> ChromeOS usermode will not pick 640x480 unless we mark it as preferred >>>>>>> or other modes are eliminated. >>>>>>> >>>>>>> So we have to come up with the right way for the usermode to pick >>>>>>> 640x480. >>>>>>> >>>>>>> We will discuss this a bit more and come up with a different change. >>>>>> >>>>>> Can you provide the exact EDID from the failing test case? Maybe that >>>>>> will help shed some light on what's going on. I looked at the original >>>>>> commit and it just referred to 4.2.2.1, which I assume is "EDID Read >>>>>> upon HPD Plug Event", but that doesn't give details that seem relevant >>>>>> to the discussion here. >>>>> >>>>> Yes so it is 4.2.2.1 and 4.2.2.6. >>>>> >>>>> That alone wont give the full picture. >>>>> >>>>> So its a combination of things. >>>>> >>>>> While running the test, the test equipment published only one mode. >>>>> But we could not support that mode because of 2 lanes. >>>>> Equipment did not add 640x480 to the list of modes. >>>>> DRM fwk will also not add it because count_modes is not 0 ( there was >>>>> one mode ). >>>>> So we ended up making these changes. >>>> >>>> I think a proper solution might be to rewrite >>>> drm_helper_probe_single_connector_modes() in the following way: >>>> - call get_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is 0, call drm_add_override_edid_modes() >>>> - validate the result >>>> - prune invalid >>>> >>>> - if the number of modes is still 0, call drm_add_modes_noedid() >>>> - validate the result >>>> - prune invalid >>>> >>>> [A separate change might happen here after all the checks: if the number >>>> of modes is still 0 and if it is a DP, enforce adding 640x480 even w/o >>>> validation. But generally I feel that this shouldn't be necessary >>>> because the previous step should have added it.] >>>> >>>> This way we can be sure that all modes are validated, but still to do >>>> our best to add something supported to the list of modes. >>> >>> I'm partway through implementing / testing something similar to this. >>> ;-) My logic is slightly different than yours, though. In the very >>> least I'm not convinced that we want to add the higher resolution >>> modes (like 1024x768) if all the modes fail to validate. The DP spec >>> only claims 640x480 is always supported. The higher resolution modes >>> are for when the EDID fails to read I think. Similarly I'm not >>> convinced that we should do pruning before deciding on >>> drm_add_override_edid_modes(). >> >> >> I think pruning before drm_add_override_edid_modes() would allow one to >> use override if the first read returned some modes which are invalid. > > Yeah, I'm less certain about drm_add_override_edid_modes(), but as per > documented it's only to be used if the EDID failed to read. > > If someone has an actual use case where they need to add the override > modes for this specific case then we can, but I think it can be done > separately once someone has an actual use case. > > >> Regarding 1024 vs 640. For the restructure we shouldn't change this. And >> I'd actually point to the following commit message: >> >> commit 9632b41f00cc2fb2846569cc99dbeef78e5c94a0 >> Author: Adam Jackson <ajax@redhat.com> >> Date: Mon Nov 23 14:23:07 2009 -0500 >> >> drm/modes: Fall back to 1024x768 instead of 800x600 >> >> This matches the X server's fallback modes when using RANDR 1.2. >> >> See also: http://bugzilla.redhat.com/538761 >> >> Signed-off-by: Adam Jackson <ajax@redhat.com> >> Signed-off-by: Dave Airlie <airlied@redhat.com> >> >> >> So I'd say, let's leave 1024 as is and just try them if all other modes >> are invalid. > > I'm pretty strongly against adding 1024x768 when all modes fail to > validate. Specifically: > > If the EDID fully fails to read then adding these higher resolution > modes makes sense. We have no knowledge at all about the display in > this case and so we can guess that some standard higher resolutions > might make sense. In the case we're dealing with here, we have very > specific knowledge about what the display said it could handle and we > can't support any of them. The DP spec _only_ lists 640x480 as a > required mode so that's the only one we should add. Then this should be a DP-specific override happening after all the pruning. -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() 2022-04-26 15:37 ` Abhinav Kumar @ 2022-04-26 18:48 ` Doug Anderson -1 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 18:48 UTC (permalink / raw) To: Abhinav Kumar Cc: freedreno, Sankeerth Billakanti, David Airlie, linux-arm-msm, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Bjorn Andersson, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Stephen Boyd, Sean Paul Hi, On Tue, Apr 26, 2022 at 8:37 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > > Can you provide the exact EDID from the failing test case? Maybe that > > will help shed some light on what's going on. I looked at the original > > commit and it just referred to 4.2.2.1, which I assume is "EDID Read > > upon HPD Plug Event", but that doesn't give details that seem relevant > > to the discussion here. > > Yes so it is 4.2.2.1 and 4.2.2.6. > > That alone wont give the full picture. > > So its a combination of things. > > While running the test, the test equipment published only one mode. > But we could not support that mode because of 2 lanes. > Equipment did not add 640x480 to the list of modes. > DRM fwk will also not add it because count_modes is not 0 ( there was > one mode ). > So we ended up making these changes. Ah! This is useful context and makes tons of sense. This really feels like something that could be handled in the core. OK, See: https://lore.kernel.org/r/20220426114627.2.I4ac7f55aa446699f8c200a23c10463256f6f439f@changeid > > I guess maybe what's happening is that the test case is giving an EDID > > where all the modes are not supportable by the current clock rate / > > lanes? ...and then somehow we're not falling back to 640x480. It's > > always possible that this is a userspace problem. > > > > In any case, would you object to a revert of the patches in the short term? > > Not sure, if you saw this change kuogee posted last night. > https://patchwork.freedesktop.org/patch/483415/ > We did decided to remove all the code related to these test cases and > handle them in IGT. I hadn't seen it yet and I wasn't CCed. :( I'll take a look now. ^ permalink raw reply [flat|nested] 42+ messages in thread
* Re: [Freedreno] [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() @ 2022-04-26 18:48 ` Doug Anderson 0 siblings, 0 replies; 42+ messages in thread From: Doug Anderson @ 2022-04-26 18:48 UTC (permalink / raw) To: Abhinav Kumar Cc: Sean Paul, Sankeerth Billakanti, David Airlie, linux-arm-msm, Stephen Boyd, LKML, dri-devel, Kuogee Hsieh, Vinod Koul, Andy Gross, Dmitry Baryshkov, Aravind Venkateswaran (QUIC), Bjorn Andersson, freedreno Hi, On Tue, Apr 26, 2022 at 8:37 AM Abhinav Kumar <quic_abhinavk@quicinc.com> wrote: > > > Can you provide the exact EDID from the failing test case? Maybe that > > will help shed some light on what's going on. I looked at the original > > commit and it just referred to 4.2.2.1, which I assume is "EDID Read > > upon HPD Plug Event", but that doesn't give details that seem relevant > > to the discussion here. > > Yes so it is 4.2.2.1 and 4.2.2.6. > > That alone wont give the full picture. > > So its a combination of things. > > While running the test, the test equipment published only one mode. > But we could not support that mode because of 2 lanes. > Equipment did not add 640x480 to the list of modes. > DRM fwk will also not add it because count_modes is not 0 ( there was > one mode ). > So we ended up making these changes. Ah! This is useful context and makes tons of sense. This really feels like something that could be handled in the core. OK, See: https://lore.kernel.org/r/20220426114627.2.I4ac7f55aa446699f8c200a23c10463256f6f439f@changeid > > I guess maybe what's happening is that the test case is giving an EDID > > where all the modes are not supportable by the current clock rate / > > lanes? ...and then somehow we're not falling back to 640x480. It's > > always possible that this is a userspace problem. > > > > In any case, would you object to a revert of the patches in the short term? > > Not sure, if you saw this change kuogee posted last night. > https://patchwork.freedesktop.org/patch/483415/ > We did decided to remove all the code related to these test cases and > handle them in IGT. I hadn't seen it yet and I wasn't CCed. :( I'll take a look now. ^ permalink raw reply [flat|nested] 42+ messages in thread
end of thread, other threads:[~2022-04-26 18:48 UTC | newest] Thread overview: 42+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2022-04-22 23:45 [PATCH] drm/msm/dp: move add fail safe mode to dp_connector_get_mode() Kuogee Hsieh 2022-04-22 23:45 ` Kuogee Hsieh 2022-04-23 0:02 ` Stephen Boyd 2022-04-23 0:02 ` Stephen Boyd 2022-04-23 0:07 ` Dmitry Baryshkov 2022-04-23 0:07 ` Dmitry Baryshkov 2022-04-23 0:12 ` Abhinav Kumar 2022-04-23 0:12 ` Abhinav Kumar 2022-04-23 6:25 ` Dmitry Baryshkov 2022-04-23 6:25 ` Dmitry Baryshkov 2022-04-23 15:33 ` Abhinav Kumar 2022-04-23 15:33 ` Abhinav Kumar 2022-04-25 23:14 ` Dmitry Baryshkov 2022-04-25 23:14 ` Dmitry Baryshkov 2022-04-26 0:26 ` Doug Anderson 2022-04-26 0:26 ` Doug Anderson 2022-04-26 1:42 ` [Freedreno] " Abhinav Kumar 2022-04-26 1:42 ` Abhinav Kumar 2022-04-26 2:18 ` Doug Anderson 2022-04-26 2:18 ` Doug Anderson 2022-04-26 3:35 ` Abhinav Kumar 2022-04-26 3:35 ` Abhinav Kumar 2022-04-26 15:20 ` Doug Anderson 2022-04-26 15:20 ` Doug Anderson 2022-04-26 15:37 ` Abhinav Kumar 2022-04-26 15:37 ` Abhinav Kumar 2022-04-26 17:01 ` Dmitry Baryshkov 2022-04-26 17:01 ` Dmitry Baryshkov 2022-04-26 17:11 ` Doug Anderson 2022-04-26 17:11 ` Doug Anderson 2022-04-26 17:24 ` Abhinav Kumar 2022-04-26 17:24 ` Abhinav Kumar 2022-04-26 17:44 ` Dmitry Baryshkov 2022-04-26 17:44 ` Dmitry Baryshkov 2022-04-26 17:56 ` Doug Anderson 2022-04-26 17:56 ` Doug Anderson 2022-04-26 18:03 ` Abhinav Kumar 2022-04-26 18:03 ` Abhinav Kumar 2022-04-26 18:04 ` Dmitry Baryshkov 2022-04-26 18:04 ` Dmitry Baryshkov 2022-04-26 18:48 ` Doug Anderson 2022-04-26 18:48 ` Doug Anderson
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.