[U-Boot] [PATCH u-boot-marvell v2 00/15] Fixes for Turris Omnia

[U-Boot] [PATCH u-boot-marvell v2 00/15] Fixes for Turris Omnia

[Marek Behún]

Hi, this is the second version of my fixes for Turris Omnia.
I removed the patches which were already applied or provided a better fix.
The other patches I shall describe now here as if this was the first version.

1. removes redundant code done by I2C mvtwsi driver from board file
2. adds XHCI support to defconfig
3. in compliance with driver model use AHCI, SATA and SCSI
4. remove legacy macros from config header
5. move I2C dependencies from header file to Kconfig for TARGET_TURRIS_OMNIA
6. add SCSI as boot target
7. board code refactoring
8. fix checkpatch warnings
9. add ATSHA204A dependency to Kconfig for TARGET_TURRIS_OMNIA
10. more board code refactoring
11. print board information in the same way Turris Mox does
12. remove watchdog header include (in Turris Mox board file as well)
13. fix setting of the regdomain environment variable used on Omnia
14. add code for handling the button on the back side of Omnia, the purpose
    of which is factory reset
15. fix I2C driver, which sometimes breaks the I2C controller until the device
    is powered off

Marek

Marek Behún (15):
  arm: mvebu: turris_omnia: remove redundant code
  arm: mvebu: turris_omnia: add XHCI to defconfig
  arm: mvebu: turris_omnia: use AHCI and SATA driver model
  arm: mvebu: turris_omnia: remove legacy macros from board header
  arm: mvebu: turris_omnia: move I2C dependencies to Kconfig
  arm: mvebu: turris_omnia: add SCSI as boot target
  arm: mvebu: turris_omnia: refactor I2C accessing code
  arm: mvebu: turris_omnia: fix checkpatch warnings
  arm: mvebu: turris_omnia: move ATSHA204A from defconfig to Kconfig
  arm: mvebu: turris_omnia: refactor more code
  arm: mvebu: turris_omnia: print board info as Turris Mox
  arm: mvebu: turris_*: remove watchdog include
  arm: mvebu: turris_omnia: fix regdomain env var setting
  arm: mvebu: turris_omnia: add RESET button handling
  i2c: mvtwsi: fix reading status register after interrupt

 arch/arm/mach-mvebu/Kconfig              |  49 ++++
 board/CZ.NIC/turris_mox/turris_mox.c     |   4 -
 board/CZ.NIC/turris_omnia/turris_omnia.c | 333 ++++++++++++-----------
 configs/turris_omnia_defconfig           |  10 +-
 drivers/i2c/mvtwsi.c                     |   1 +
 include/configs/turris_omnia.h           |  32 +--
 6 files changed, 236 insertions(+), 193 deletions(-)

-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 01/15] arm: mvebu: turris_omnia: remove redundant code

[Marek Behún]

The i2c slave disabling is done by mvtwsi driver and is not needed here.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 13 -------------
 1 file changed, 13 deletions(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 4c08f810a2..055ebad000 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -50,8 +50,6 @@ DECLARE_GLOBAL_DATA_PTR;
 #define OMNIA_ATSHA204_OTP_MAC0		3
 #define OMNIA_ATSHA204_OTP_MAC1		4
 
-#define MVTWSI_ARMADA_DEBUG_REG		0x8c
-
 /*
  * Those values and defines are taken from the Marvell U-Boot version
  * "u-boot-2013.01-2014_T3.0"
@@ -297,8 +295,6 @@ static int set_regdomain(void)
 
 int board_early_init_f(void)
 {
-	u32 i2c_debug_reg;
-
 	/* Configure MPP */
 	writel(0x11111111, MVEBU_MPP_BASE + 0x00);
 	writel(0x11111111, MVEBU_MPP_BASE + 0x04);
@@ -321,15 +317,6 @@ int board_early_init_f(void)
 	writel(OMNIA_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
 	writel(OMNIA_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
 
-	/*
-	 * Disable I2C debug mode blocking 0x64 I2C address.
-	 * Note: that would be redundant once Turris Omnia migrates to DM_I2C,
-	 * because the mvtwsi driver includes equivalent code.
-	 */
-	i2c_debug_reg = readl(MVEBU_TWSI_BASE + MVTWSI_ARMADA_DEBUG_REG);
-	i2c_debug_reg &= ~(1<<18);
-	writel(i2c_debug_reg, MVEBU_TWSI_BASE + MVTWSI_ARMADA_DEBUG_REG);
-
 	return 0;
 }
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 02/15] arm: mvebu: turris_omnia: add XHCI to defconfig

[Marek Behún]

Add XHCI_HOST and XHCI_MVEBU to defconfig, so that user's can by default
boot from USB on Turris Omnia.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 configs/turris_omnia_defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig
index a528a9b5bc..2ad2f6e431 100644
--- a/configs/turris_omnia_defconfig
+++ b/configs/turris_omnia_defconfig
@@ -58,5 +58,7 @@ CONFIG_KIRKWOOD_SPI=y
 CONFIG_USB=y
 CONFIG_DM_USB=y
 CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_MVEBU=y
 CONFIG_WDT=y
 CONFIG_WDT_ORION=y
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 03/15] arm: mvebu: turris_omnia: use AHCI and SATA driver model

[Marek Behún]

Enable AHCI, SCSI and SATA for compliance with the driver model
migration.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 configs/turris_omnia_defconfig | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig
index 2ad2f6e431..5086da13a5 100644
--- a/configs/turris_omnia_defconfig
+++ b/configs/turris_omnia_defconfig
@@ -26,6 +26,8 @@ CONFIG_SPL_SPI_LOAD=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_PCI=y
+CONFIG_CMD_SATA=y
+CONFIG_CMD_SCSI=y
 CONFIG_CMD_SF=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
@@ -39,6 +41,11 @@ CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_USE_ENV_SPI_MAX_HZ=y
 CONFIG_ENV_SPI_MAX_HZ=50000000
 CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_AHCI=y
+CONFIG_AHCI_PCI=y
+CONFIG_AHCI_MVEBU=y
+CONFIG_SATA=y
+CONFIG_SCSI=y
 CONFIG_SCSI_AHCI=y
 CONFIG_ATSHA204A=y
 CONFIG_DM_MMC=y
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 04/15] arm: mvebu: turris_omnia: remove legacy macros from board header

[Marek Behún]

These are not needed if MMC and SCSI DM drivers are used.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 include/configs/turris_omnia.h | 14 --------------
 1 file changed, 14 deletions(-)

diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h
index 0e65a12345..5e692e6829 100644
--- a/include/configs/turris_omnia.h
+++ b/include/configs/turris_omnia.h
@@ -29,20 +29,6 @@
 #define CONFIG_SPL_I2C_MUX
 #define CONFIG_SYS_I2C_MVTWSI
 
-/*
- * SDIO/MMC Card Configuration
- */
-#define CONFIG_SYS_MMC_BASE		MVEBU_SDIO_BASE
-
-/*
- * SATA/SCSI/AHCI configuration
- */
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	2
-#define CONFIG_SYS_SCSI_MAX_LUN		1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-					 CONFIG_SYS_SCSI_MAX_LUN)
-
 /* USB/EHCI configuration */
 #define CONFIG_EHCI_IS_TDI
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 05/15] arm: mvebu: turris_omnia: move I2C dependencies to Kconfig

[Marek Behún]

The I2C dependencies are defined in include/configs/turris_omnia.h,
because Turris Omnia won't boot correctly without I2C support.

Move these dependencies to Kconfig, so that they are selected if Turris
Omnia is selected as target.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 arch/arm/mach-mvebu/Kconfig    |  5 +++++
 include/configs/turris_omnia.h | 11 -----------
 2 files changed, 5 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index f99bd3bf65..2bf829d10a 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -116,6 +116,11 @@ config TARGET_DB_88F6820_AMC
 config TARGET_TURRIS_OMNIA
 	bool "Support Turris Omnia"
 	select 88F6820
+	select DM_I2C
+	select I2C_MUX
+	select I2C_MUX_PCA954x
+	select SPL_I2C_MUX
+	select SYS_I2C_MVTWSI
 
 config TARGET_TURRIS_MOX
 	bool "Support Turris Mox"
diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h
index 5e692e6829..5a7539c9be 100644
--- a/include/configs/turris_omnia.h
+++ b/include/configs/turris_omnia.h
@@ -18,17 +18,6 @@
  */
 #define CONFIG_SYS_TCLK		250000000	/* 250MHz */
 
-/*
- * Commands configuration
- */
-
-/* I2C support */
-#define CONFIG_DM_I2C
-#define CONFIG_I2C_MUX
-#define CONFIG_I2C_MUX_PCA954x
-#define CONFIG_SPL_I2C_MUX
-#define CONFIG_SYS_I2C_MVTWSI
-
 /* USB/EHCI configuration */
 #define CONFIG_EHCI_IS_TDI
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 06/15] arm: mvebu: turris_omnia: add SCSI as boot target

[Marek Behún]

If SCSI is enabled, U-Boot should try to boot also from SCSI device on
Turris Omnia.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 include/configs/turris_omnia.h | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h
index 5a7539c9be..5b9639e050 100644
--- a/include/configs/turris_omnia.h
+++ b/include/configs/turris_omnia.h
@@ -90,9 +90,16 @@
 #define BOOT_TARGET_DEVICES_USB(func)
 #endif
 
+#ifdef CONFIG_SCSI
+#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
+#else
+#define BOOT_TARGET_DEVICES_SCSI(func)
+#endif
+
 #define BOOT_TARGET_DEVICES(func) \
 	BOOT_TARGET_DEVICES_MMC(func) \
 	BOOT_TARGET_DEVICES_USB(func) \
+	BOOT_TARGET_DEVICES_SCSI(func) \
 	func(PXE, pxe, na) \
 	func(DHCP, dhcp, na)
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 07/15] arm: mvebu: turris_omnia: refactor I2C accessing code

[Marek Behún]

Refactor code which accesses the microcontroller and EEPROM via I2C.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 205 ++++++++++++-----------
 1 file changed, 109 insertions(+), 96 deletions(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 055ebad000..6b8fa53c98 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -32,18 +32,25 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#define OMNIA_I2C_EEPROM_DM_NAME	"i2c at 11000->i2cmux at 70->i2c at 0"
-#define OMNIA_I2C_EEPROM		0x54
-#define OMNIA_I2C_EEPROM_CONFIG_ADDR	0x0
-#define OMNIA_I2C_EEPROM_ADDRLEN	2
+#define OMNIA_I2C_BUS_NAME		"i2c at 11000->i2cmux at 70->i2c at 0"
+
+#define OMNIA_I2C_MCU_CHIP_ADDR		0x2a
+#define OMNIA_I2C_MCU_CHIP_LEN		1
+
+#define OMNIA_I2C_EEPROM_CHIP_ADDR	0x54
+#define OMNIA_I2C_EEPROM_CHIP_LEN	2
 #define OMNIA_I2C_EEPROM_MAGIC		0x0341a034
 
-#define OMNIA_I2C_MCU_DM_NAME		"i2c at 11000->i2cmux at 70->i2c at 0"
-#define OMNIA_I2C_MCU_ADDR_STATUS	0x1
-#define OMNIA_I2C_MCU_SATA		0x20
-#define OMNIA_I2C_MCU_CARDDET		0x10
-#define OMNIA_I2C_MCU			0x2a
-#define OMNIA_I2C_MCU_WDT_ADDR		0x0b
+enum mcu_commands {
+	CMD_GET_STATUS_WORD	= 0x01,
+	CMD_GET_RESET		= 0x09,
+	CMD_WATCHDOG_STATE	= 0x0b,
+};
+
+enum status_word_bits {
+	CARD_DET_STSBIT		= 0x0010,
+	MSATA_IND_STSBIT	= 0x0020,
+};
 
 #define OMNIA_ATSHA204_OTP_VERSION	0
 #define OMNIA_ATSHA204_OTP_SERIAL	1
@@ -85,48 +92,97 @@ static struct serdes_map board_serdes_map_sata[] = {
 	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}
 };
 
-static bool omnia_detect_sata(void)
+static struct udevice *omnia_get_i2c_chip(const char *name, uint addr,
+					  uint offset_len)
 {
 	struct udevice *bus, *dev;
-	int ret, retry = 3;
-	u16 mode;
-
-	puts("SERDES0 card detect: ");
+	int ret;
 
-	if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_MCU_DM_NAME, &bus)) {
-		puts("Cannot find MCU bus!\n");
-		return false;
+	ret = uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_BUS_NAME, &bus);
+	if (ret) {
+		printf("Cannot get I2C bus %s: uclass_get_device_by_name failed: %i\n",
+		       OMNIA_I2C_BUS_NAME, ret);
+		return NULL;
 	}
 
-	ret = i2c_get_chip(bus, OMNIA_I2C_MCU, 1, &dev);
+	ret = i2c_get_chip(bus, addr, offset_len, &dev);
 	if (ret) {
-		puts("Cannot get MCU chip!\n");
-		return false;
+		printf("Cannot get %s I2C chip: i2c_get_chip failed: %i\n",
+		       name, ret);
+		return NULL;
 	}
 
-	for (; retry > 0; --retry) {
-		ret = dm_i2c_read(dev, OMNIA_I2C_MCU_ADDR_STATUS, (uchar *) &mode, 2);
-		if (!ret)
-			break;
-	}
+	return dev;
+}
+
+static int omnia_mcu_read(u8 cmd, void *buf, int len)
+{
+	struct udevice *chip;
+
+	chip = omnia_get_i2c_chip("MCU", OMNIA_I2C_MCU_CHIP_ADDR,
+				  OMNIA_I2C_MCU_CHIP_LEN);
+	if (!chip)
+		return -ENODEV;
+
+	return dm_i2c_read(chip, cmd, buf, len);
+}
 
-	if (!retry) {
-		puts("I2C read failed! Default PEX\n");
+#ifndef CONFIG_SPL_BUILD
+static int omnia_mcu_write(u8 cmd, const void *buf, int len)
+{
+	struct udevice *chip;
+
+	chip = omnia_get_i2c_chip("MCU", OMNIA_I2C_MCU_CHIP_ADDR,
+				  OMNIA_I2C_MCU_CHIP_LEN);
+	if (!chip)
+		return -ENODEV;
+
+	return dm_i2c_write(chip, cmd, buf, len);
+}
+
+static bool disable_mcu_watchdog(void)
+{
+	int ret;
+
+	puts("Disabling MCU watchdog... ");
+
+	ret = omnia_mcu_write(CMD_WATCHDOG_STATE, "\x00", 1);
+	if (ret) {
+		printf("omnia_mcu_write failed: %i\n", ret);
 		return false;
 	}
 
-	if (!(mode & OMNIA_I2C_MCU_CARDDET)) {
-		puts("NONE\n");
+	puts("disabled\n");
+
+	return true;
+}
+#endif
+
+static bool omnia_detect_sata(void)
+{
+	int ret;
+	u16 stsword;
+
+	puts("MiniPCIe/mSATA card detection... ");
+
+	ret = omnia_mcu_read(CMD_GET_STATUS_WORD, &stsword, sizeof(stsword));
+	if (ret) {
+		printf("omnia_mcu_read failed: %i, defaulting to MiniPCIe card\n",
+		       ret);
 		return false;
 	}
 
-	if (mode & OMNIA_I2C_MCU_SATA) {
-		puts("SATA\n");
-		return true;
-	} else {
-		puts("PEX\n");
+	if (!(stsword & CARD_DET_STSBIT)) {
+		puts("none\n");
 		return false;
 	}
+
+	if (stsword & MSATA_IND_STSBIT)
+		puts("mSATA\n");
+	else
+		puts("MiniPCIe\n");
+
+	return stsword & MSATA_IND_STSBIT ? true : false;
 }
 
 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
@@ -151,42 +207,32 @@ struct omnia_eeprom {
 
 static bool omnia_read_eeprom(struct omnia_eeprom *oep)
 {
-	struct udevice *bus, *dev;
-	int ret, crc, retry = 3;
+	struct udevice *chip;
+	u32 crc;
+	int ret;
+
+	chip = omnia_get_i2c_chip("EEPROM", OMNIA_I2C_EEPROM_CHIP_ADDR,
+				  OMNIA_I2C_EEPROM_CHIP_LEN);
 
-	if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_EEPROM_DM_NAME, &bus)) {
-		puts("Cannot find EEPROM bus\n");
+	if (!chip)
 		return false;
-	}
 
-	ret = i2c_get_chip(bus, OMNIA_I2C_EEPROM, OMNIA_I2C_EEPROM_ADDRLEN, &dev);
+	ret = dm_i2c_read(chip, 0, (void *)oep, sizeof(*oep));
 	if (ret) {
-		puts("Cannot get EEPROM chip\n");
+		printf("dm_i2c_read failed: %i, cannot read EEPROM\n", ret);
 		return false;
 	}
 
-	for (; retry > 0; --retry) {
-		ret = dm_i2c_read(dev, OMNIA_I2C_EEPROM_CONFIG_ADDR, (uchar *) oep, sizeof(struct omnia_eeprom));
-		if (ret)
-			continue;
-
-		if (oep->magic != OMNIA_I2C_EEPROM_MAGIC) {
-			puts("I2C EEPROM missing magic number!\n");
-			continue;
-		}
-
-		crc = crc32(0, (unsigned char *) oep,
-			    sizeof(struct omnia_eeprom) - 4);
-		if (crc == oep->crc) {
-			break;
-		} else {
-			printf("CRC of EEPROM memory config failed! "
-			       "calc=0x%04x saved=0x%04x\n", crc, oep->crc);
-		}
+	if (oep->magic != OMNIA_I2C_EEPROM_MAGIC) {
+		printf("bad EEPROM magic number (%08x, should be %08x)\n",
+		       oep->magic, OMNIA_I2C_EEPROM_MAGIC);
+		return false;
 	}
 
-	if (!retry) {
-		puts("I2C EEPROM read failed!\n");
+	crc = crc32(0, (void *)oep, sizeof(*oep) - 4);
+	if (crc != oep->crc) {
+		printf("bad EEPROM CRC (stored %08x, computed %08x)\n",
+		       oep->crc, crc);
 		return false;
 	}
 
@@ -320,46 +366,13 @@ int board_early_init_f(void)
 	return 0;
 }
 
-#ifndef CONFIG_SPL_BUILD
-static bool disable_mcu_watchdog(void)
-{
-	struct udevice *bus, *dev;
-	int ret, retry = 3;
-	uchar buf[1] = {0x0};
-
-	if (uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_MCU_DM_NAME, &bus)) {
-		puts("Cannot find MCU bus! Can not disable MCU WDT.\n");
-		return false;
-	}
-
-	ret = i2c_get_chip(bus, OMNIA_I2C_MCU, 1, &dev);
-	if (ret) {
-		puts("Cannot get MCU chip! Can not disable MCU WDT.\n");
-		return false;
-	}
-
-	for (; retry > 0; --retry)
-		if (!dm_i2c_write(dev, OMNIA_I2C_MCU_WDT_ADDR, (uchar *) buf, 1))
-			break;
-
-	if (retry <= 0) {
-		puts("I2C MCU watchdog failed to disable!\n");
-		return false;
-	}
-
-	return true;
-}
-#endif
-
 int board_init(void)
 {
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
 #ifndef CONFIG_SPL_BUILD
-	if (disable_mcu_watchdog())
-		puts("Disabled MCU startup watchdog.\n");
-
+	disable_mcu_watchdog();
 	set_regdomain();
 #endif
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 08/15] arm: mvebu: turris_omnia: fix checkpatch warnings

[Marek Behún]

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 6b8fa53c98..d4fb89f15f 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -290,12 +290,12 @@ static struct mv_ddr_topology_map board_topology_map_2g = {
 
 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
 {
-	static int mem = 0;
+	static int mem;
 	struct omnia_eeprom oep;
 
 	/* Get the board config from EEPROM */
-	if (mem == 0) {
-		if(!omnia_read_eeprom(&oep))
+	if (!mem) {
+		if (!omnia_read_eeprom(&oep))
 			goto out;
 
 		printf("Memory config in EEPROM: 0x%02x\n", oep.ramsize);
@@ -368,7 +368,7 @@ int board_early_init_f(void)
 
 int board_init(void)
 {
-	/* adress of boot parameters */
+	/* address of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
 
 #ifndef CONFIG_SPL_BUILD
@@ -391,9 +391,9 @@ int board_late_init(void)
 #ifdef CONFIG_ATSHA204A
 static struct udevice *get_atsha204a_dev(void)
 {
-	static struct udevice *dev = NULL;
+	static struct udevice *dev;
 
-	if (dev != NULL)
+	if (dev)
 		return dev;
 
 	if (uclass_get_device_by_name(UCLASS_MISC, "atsha204a at 64", &dev)) {
@@ -420,13 +420,13 @@ int checkboard(void)
 
 		err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
 				     OMNIA_ATSHA204_OTP_VERSION,
-				     (u8 *) &version_num);
+				     (u8 *)&version_num);
 		if (err)
 			goto out;
 
 		err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
 				     OMNIA_ATSHA204_OTP_SERIAL,
-				     (u8 *) &serial_num);
+				     (u8 *)&serial_num);
 		if (err)
 			goto out;
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 09/15] arm: mvebu: turris_omnia: move ATSHA204A from defconfig to Kconfig

[Marek Behún]

This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 arch/arm/mach-mvebu/Kconfig              |  1 +
 board/CZ.NIC/turris_omnia/turris_omnia.c | 11 -----------
 configs/turris_omnia_defconfig           |  1 -
 3 files changed, 1 insertion(+), 12 deletions(-)

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 2bf829d10a..fc29c3b084 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -121,6 +121,7 @@ config TARGET_TURRIS_OMNIA
 	select I2C_MUX_PCA954x
 	select SPL_I2C_MUX
 	select SYS_I2C_MVTWSI
+	select ATSHA204A
 
 config TARGET_TURRIS_MOX
 	bool "Support Turris Mox"
diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index d4fb89f15f..640ee2a2a3 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -18,10 +18,7 @@
 #include <dm/uclass.h>
 #include <fdt_support.h>
 #include <time.h>
-
-#ifdef CONFIG_ATSHA204A
 # include <atsha204a-i2c.h>
-#endif
 
 #ifdef CONFIG_WDT_ORION
 # include <wdt.h>
@@ -388,7 +385,6 @@ int board_late_init(void)
 	return 0;
 }
 
-#ifdef CONFIG_ATSHA204A
 static struct udevice *get_atsha204a_dev(void)
 {
 	static struct udevice *dev;
@@ -403,14 +399,12 @@ static struct udevice *get_atsha204a_dev(void)
 
 	return dev;
 }
-#endif
 
 int checkboard(void)
 {
 	u32 version_num, serial_num;
 	int err = 1;
 
-#ifdef CONFIG_ATSHA204A
 	struct udevice *dev = get_atsha204a_dev();
 
 	if (dev) {
@@ -434,8 +428,6 @@ int checkboard(void)
 	}
 
 out:
-#endif
-
 	if (err)
 		printf("Board: Turris Omnia (ver N/A). SN: N/A\n");
 	else
@@ -458,7 +450,6 @@ static void increment_mac(u8 *mac)
 
 int misc_init_r(void)
 {
-#ifdef CONFIG_ATSHA204A
 	int err;
 	struct udevice *dev = get_atsha204a_dev();
 	u8 mac0[4], mac1[4], mac[6];
@@ -503,8 +494,6 @@ int misc_init_r(void)
 		eth_env_set_enetaddr("eth2addr", mac);
 
 out:
-#endif
-
 	return 0;
 }
 
diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig
index 5086da13a5..5a09dc3033 100644
--- a/configs/turris_omnia_defconfig
+++ b/configs/turris_omnia_defconfig
@@ -47,7 +47,6 @@ CONFIG_AHCI_MVEBU=y
 CONFIG_SATA=y
 CONFIG_SCSI=y
 CONFIG_SCSI_AHCI=y
-CONFIG_ATSHA204A=y
 CONFIG_DM_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_MV=y
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 10/15] arm: mvebu: turris_omnia: refactor more code

[Marek Behún]

Refactor RAM size reading from EEPROM in preparation for next patch.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 58 ++++++++++++------------
 1 file changed, 28 insertions(+), 30 deletions(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 640ee2a2a3..8571541b0a 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -236,6 +236,31 @@ static bool omnia_read_eeprom(struct omnia_eeprom *oep)
 	return true;
 }
 
+static int omnia_get_ram_size_gb(void)
+{
+	static int ram_size;
+	struct omnia_eeprom oep;
+
+	if (!ram_size) {
+		/* Get the board config from EEPROM */
+		if (omnia_read_eeprom(&oep)) {
+			debug("Memory config in EEPROM: 0x%02x\n", oep.ramsize);
+
+			if (oep.ramsize == 0x2)
+				ram_size = 2;
+			else
+				ram_size = 1;
+		} else {
+			/* Hardcoded fallback */
+			puts("Memory config from EEPROM read failed!\n");
+			puts("Falling back to default 1 GiB!\n");
+			ram_size = 1;
+		}
+	}
+
+	return ram_size;
+}
+
 /*
  * Define the DDR layout / topology here in the board file. This will
  * be used by the DDR3 init code in the SPL U-Boot version to configure
@@ -287,37 +312,10 @@ static struct mv_ddr_topology_map board_topology_map_2g = {
 
 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
 {
-	static int mem;
-	struct omnia_eeprom oep;
-
-	/* Get the board config from EEPROM */
-	if (!mem) {
-		if (!omnia_read_eeprom(&oep))
-			goto out;
-
-		printf("Memory config in EEPROM: 0x%02x\n", oep.ramsize);
-
-		if (oep.ramsize == 0x2)
-			mem = 2;
-		else
-			mem = 1;
-	}
-
-out:
-	/* Hardcoded fallback */
-	if (mem == 0) {
-		puts("WARNING: Memory config from EEPROM read failed.\n");
-		puts("Falling back to default 1GiB map.\n");
-		mem = 1;
-	}
-
-	/* Return the board topology as defined in the board code */
-	if (mem == 1)
-		return &board_topology_map_1g;
-	if (mem == 2)
+	if (omnia_get_ram_size_gb() == 2)
 		return &board_topology_map_2g;
-
-	return &board_topology_map_1g;
+	else
+		return &board_topology_map_1g;
 }
 
 #ifndef CONFIG_SPL_BUILD
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 11/15] arm: mvebu: turris_omnia: print board info as Turris Mox

[Marek Behún]

Unify the way how Omnia and Mox print board information (RAM size and
serial number).

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 8571541b0a..54efd2d4c9 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -426,11 +426,13 @@ int checkboard(void)
 	}
 
 out:
+	printf("Turris Omnia:\n");
+	printf("  RAM size: %i MiB\n", omnia_get_ram_size_gb() * 1024);
 	if (err)
-		printf("Board: Turris Omnia (ver N/A). SN: N/A\n");
+		printf("  Serial Number: unknown\n");
 	else
-		printf("Board: Turris Omnia SNL %08X%08X\n",
-		       be32_to_cpu(version_num), be32_to_cpu(serial_num));
+		printf("  Serial Number: %08X%08X\n", be32_to_cpu(version_num),
+		       be32_to_cpu(serial_num));
 
 	return 0;
 }
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 12/15] arm: mvebu: turris_*: remove watchdog include

[Marek Behún]

Since board watchdog is now unified and not handled in board files,
remove the unnecessary includes.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_mox/turris_mox.c     | 4 ----
 board/CZ.NIC/turris_omnia/turris_omnia.c | 4 ----
 2 files changed, 8 deletions(-)

diff --git a/board/CZ.NIC/turris_mox/turris_mox.c b/board/CZ.NIC/turris_mox/turris_mox.c
index 8a4872343b..3818e3752a 100644
--- a/board/CZ.NIC/turris_mox/turris_mox.c
+++ b/board/CZ.NIC/turris_mox/turris_mox.c
@@ -16,10 +16,6 @@
 #include <fdt_support.h>
 #include <environment.h>
 
-#ifdef CONFIG_WDT_ARMADA_37XX
-#include <wdt.h>
-#endif
-
 #include "mox_sp.h"
 
 #define MAX_MOX_MODULES		10
diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index 54efd2d4c9..b073a985a5 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -20,10 +20,6 @@
 #include <time.h>
 # include <atsha204a-i2c.h>
 
-#ifdef CONFIG_WDT_ORION
-# include <wdt.h>
-#endif
-
 #include "../drivers/ddr/marvell/a38x/ddr3_init.h"
 #include <../serdes/a38x/high_speed_env_spec.h>
 
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 13/15] arm: mvebu: turris_omnia: fix regdomain env var setting

[Marek Behún]

The regdomain environment variable is set according to value read from
EEPROM. This has to be done in board_late_init, after the environment
variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
for the Turris Omnia target.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 board/CZ.NIC/turris_omnia/turris_omnia.c | 1 -
 1 file changed, 1 deletion(-)

diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index b073a985a5..af43ee23d9 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -364,7 +364,6 @@ int board_init(void)
 
 #ifndef CONFIG_SPL_BUILD
 	disable_mcu_watchdog();
-	set_regdomain();
 #endif
 
 	return 0;
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Marek Behún]

There is a Factory RESET button on the back side of the Turris Omnia
router. When user presses this button before powering the device up and
keeps it pressed, the microcontroller prevents the main CPU from booting
and counts how long the RESET button is being pressed (and indicates
this by lighting up front LEDs).

The idea behind this is that the user can boot the device into several
Factory RESET modes.

This patch adds support for U-Boot to read into which Factory RESET mode
the user booted the device. The value is an integer stored into the
omnia_reset environment variable. It is 0 if the button was not pressed
at all during power up, otherwise it is the number identifying the
Factory RESET mode.

This patch also adds support for configuring (via Kconfig) if the
bootcmd environment variable should be overwritten if this Factory RESET
button was pressed during device powerup, and if this configuration
option is enabled, the value by which bootcmd should be overwritten with
is also a configurable option. The default value sets the colors of all
the LEDs on the front panel to green, then loads the rescue system image
from the SPI flash memory and then boots it.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
---
 arch/arm/mach-mvebu/Kconfig              | 43 ++++++++++++++++++++++++
 board/CZ.NIC/turris_omnia/turris_omnia.c | 23 +++++++++++++
 2 files changed, 66 insertions(+)

diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index fc29c3b084..4229a505d1 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -116,6 +116,7 @@ config TARGET_DB_88F6820_AMC
 config TARGET_TURRIS_OMNIA
 	bool "Support Turris Omnia"
 	select 88F6820
+	select BOARD_LATE_INIT
 	select DM_I2C
 	select I2C_MUX
 	select I2C_MUX_PCA954x
@@ -165,6 +166,48 @@ config TARGET_DB_XC3_24G4XG
 
 endchoice
 
+if TARGET_TURRIS_OMNIA
+
+config TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
+	bool "Turris Omnia RESET button overwrites bootcmd"
+	default y
+	help
+	  There is a RESET button on the back side of the Turris Omnia router,
+	  which is read by the microcontroller before the main CPU is booted.
+	  If this button is pressed during device poweron, the CPU is only
+	  booted after the button is released.
+
+	  The CPU can then read how long the RESET button was pressed (in time
+	  intervals of cca 2 seconds, at most 12 different values), and U-Boot
+	  stores this value into omnia_reset environment variable.
+	  The microcontroller also lights up one front LED every time interval,
+	  so that users can see the value they are forcing.
+
+	  If this option is enabled, the board code will also overwrite the
+	  bootcmd variable with a constant configurable in this configuration
+	  (config TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE) if the RESET button was
+	  pressed for at least one time interval.
+
+	  Otherwise only the omnia_reset environment variable is set.
+
+config TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE
+	string "Turris Omnia RESET button bootcmd value"
+	default "i2c dev 2; i2c mw 0x2a.1 0x3 0x1c 1; i2c mw 0x2a.1 0x4 0x1c 1; mw.l 0x01000000 0x00ff000c; i2c write 0x01000000 0x2a.1 0x5 4 -s; setenv bootargs \\\"$bootargs omniarescue=$omnia_reset\\\"; sf probe; sf read 0x1000000 0x100000 0x700000; bootm 0x1000000; bootz 0x1000000"
+	depends on TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
+	help
+	  If the RESET button is pressed during device poweron and released at
+	  least after cca 2 seconds, the bootcmd will be overwritten with this
+	  value.
+
+	  You can use the omnia_reset environment variable in this command to
+	  detect how long the reset button was pressed (or pass this value to
+	  Linux as a boot parameter).
+
+	  The default value of this command set the front LEDs to green color
+	  and then tries to boot rescue system from SPI memory.
+
+endif
+
 config SYS_BOARD
 	default "clearfog" if TARGET_CLEARFOG
 	default "helios4" if TARGET_HELIOS4
diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
index af43ee23d9..91fce6370c 100644
--- a/board/CZ.NIC/turris_omnia/turris_omnia.c
+++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
@@ -328,6 +328,28 @@ static int set_regdomain(void)
 	printf("Regdomain set to %s\n", rd);
 	return env_set("regdomain", rd);
 }
+
+static void handle_reset_button(void)
+{
+	int ret;
+	u8 reset_status;
+
+	ret = omnia_mcu_read(CMD_GET_RESET, &reset_status, 1);
+	if (ret) {
+		printf("omnia_mcu_read failed: %i, reset status unknown!\n",
+		       ret);
+		return;
+	}
+
+	env_set_ulong("omnia_reset", reset_status);
+
+#ifdef CONFIG_TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
+	if (reset_status) {
+		printf("RESET button was pressed, overwriting bootcmd!\n");
+		env_set("bootcmd", CONFIG_TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE);
+	}
+#endif
+}
 #endif
 
 int board_early_init_f(void)
@@ -373,6 +395,7 @@ int board_late_init(void)
 {
 #ifndef CONFIG_SPL_BUILD
 	set_regdomain();
+	handle_reset_button();
 #endif
 
 	return 0;
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Marek Behún]

The twsi_wait function reads the control register for interrupt flag,
and if interrupt flag is present, it immediately reads status register.

On our device this sometimes causes bad value being read from status
register, as if the value was not yet updated.

My theory is that the controller does approximately this:
  1. sets interrupt flag in control register,
  2. sets the value of status register,
  3. causes an interrupt

In U-Boot we do not use interrupts, so I think that it is possible that
sometimes the status register in the twsi_wait function is read between
points 1 and 2.

The bug does not appear if I add a small delay before reading status
register.

Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
register.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Heiko Schocher <hs@denx.de>
---
 drivers/i2c/mvtwsi.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
index 74ac0a4aa7..483a71ba12 100644
--- a/drivers/i2c/mvtwsi.c
+++ b/drivers/i2c/mvtwsi.c
@@ -271,6 +271,7 @@ static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status,
 	do {
 		control = readl(&twsi->control);
 		if (control & MVTWSI_CONTROL_IFLG) {
+			ndelay(100);
 			status = readl(&twsi->status);
 			if (status == expected_status)
 				return 0;
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2 01/15] arm: mvebu: turris_omnia: remove redundant code

[Heiko Schocher]

Hello Marek,

Am 30.04.2019 um 03:48 schrieb Marek Behún:
> The i2c slave disabling is done by mvtwsi driver and is not needed here.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> ---
>   board/CZ.NIC/turris_omnia/turris_omnia.c | 13 -------------
>   1 file changed, 13 deletions(-)

Acked-by: Heiko Schocher <hs@denx.de>

bye,
Heiko

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs at denx.de

[U-Boot] [PATCH u-boot-marvell v2 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Heiko Schocher]

Hello Marek,

Am 30.04.2019 um 03:48 schrieb Marek Behún:
> The twsi_wait function reads the control register for interrupt flag,
> and if interrupt flag is present, it immediately reads status register.
> 
> On our device this sometimes causes bad value being read from status
> register, as if the value was not yet updated.
> 
> My theory is that the controller does approximately this:
>    1. sets interrupt flag in control register,
>    2. sets the value of status register,
>    3. causes an interrupt
> 
> In U-Boot we do not use interrupts, so I think that it is possible that
> sometimes the status register in the twsi_wait function is read between
> points 1 and 2.
> 
> The bug does not appear if I add a small delay before reading status
> register.

Strange.

> Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
> function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
> register.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> Cc: Mario Six <mario.six@gdsys.cc>
> Cc: Stefan Roese <sr@denx.de>
> Cc: Baruch Siach <baruch@tkos.co.il>
> Cc: Heiko Schocher <hs@denx.de>
> ---
>   drivers/i2c/mvtwsi.c | 1 +
>   1 file changed, 1 insertion(+)
> 
> diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
> index 74ac0a4aa7..483a71ba12 100644
> --- a/drivers/i2c/mvtwsi.c
> +++ b/drivers/i2c/mvtwsi.c
> @@ -271,6 +271,7 @@ static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status,
>   	do {
>   		control = readl(&twsi->control);
>   		if (control & MVTWSI_CONTROL_IFLG) {
> +			ndelay(100);
>   			status = readl(&twsi->status);
>   			if (status == expected_status)
>   				return 0;
> 

Can you please add a comment in the code too?

Beside of that:

Acked-by: Heiko Schocher <hs@denx.de>

bye,
Heiko
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs at denx.de

[U-Boot] [PATCH u-boot-marvell v2 05/15] arm: mvebu: turris_omnia: move I2C dependencies to Kconfig

[Heiko Schocher]

Hello Marek,

Am 30.04.2019 um 03:48 schrieb Marek Behún:
> The I2C dependencies are defined in include/configs/turris_omnia.h,
> because Turris Omnia won't boot correctly without I2C support.
> 
> Move these dependencies to Kconfig, so that they are selected if Turris
> Omnia is selected as target.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> ---
>   arch/arm/mach-mvebu/Kconfig    |  5 +++++
>   include/configs/turris_omnia.h | 11 -----------
>   2 files changed, 5 insertions(+), 11 deletions(-)

Reviewed-by: Heiko Schocher <hs@denx.de>

bye,
Heiko
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs at denx.de

[U-Boot] [PATCH u-boot-marvell v2.1 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Marek Behún]

The twsi_wait function reads the control register for interrupt flag,
and if interrupt flag is present, it immediately reads status register.

On our device this sometimes causes bad value being read from status
register, as if the value was not yet updated.

My theory is that the controller does approximately this:
  1. sets interrupt flag in control register,
  2. sets the value of status register,
  3. causes an interrupt

In U-Boot we do not use interrupts, so I think that it is possible that
sometimes the status register in the twsi_wait function is read between
points 1 and 2.

The bug does not appear if I add a small delay before reading status
register.

Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
register.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
---
 drivers/i2c/mvtwsi.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
index 74ac0a4aa7..0a2dafcec6 100644
--- a/drivers/i2c/mvtwsi.c
+++ b/drivers/i2c/mvtwsi.c
@@ -271,6 +271,17 @@ static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status,
 	do {
 		control = readl(&twsi->control);
 		if (control & MVTWSI_CONTROL_IFLG) {
+			/*
+			 * On Armada 38x it seems that the controller works as
+			 * if it first set the MVTWSI_CONTROL_IFLAG in the
+			 * control register and only after that it changed the
+			 * status register.
+			 * This sometimes caused weird bugs which only appeared
+			 * on selected I2C speeds and even then only sometimes.
+			 * We therefore add here a simple ndealy(100), which
+			 * seems to fix this weird bug.
+			 */
+			ndelay(100);
 			status = readl(&twsi->status);
 			if (status == expected_status)
 				return 0;
-- 
2.21.0

[U-Boot] [PATCH u-boot-marvell v2.1 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Heiko Schocher]

Hello Marek,

Am 01.05.2019 um 23:09 schrieb Marek Behún:
> The twsi_wait function reads the control register for interrupt flag,
> and if interrupt flag is present, it immediately reads status register.
> 
> On our device this sometimes causes bad value being read from status
> register, as if the value was not yet updated.
> 
> My theory is that the controller does approximately this:
>    1. sets interrupt flag in control register,
>    2. sets the value of status register,
>    3. causes an interrupt
> 
> In U-Boot we do not use interrupts, so I think that it is possible that
> sometimes the status register in the twsi_wait function is read between
> points 1 and 2.
> 
> The bug does not appear if I add a small delay before reading status
> register.
> 
> Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
> function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
> register.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> Acked-by: Heiko Schocher <hs@denx.de>
> Cc: Mario Six <mario.six@gdsys.cc>
> Cc: Stefan Roese <sr@denx.de>
> Cc: Baruch Siach <baruch@tkos.co.il>
> ---
>   drivers/i2c/mvtwsi.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)

Thanks for adding the comment

Reviewed-by: Heiko Schocher <hs@denx.de>

bye,
Heiko
-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-52   Fax: +49-8142-66989-80   Email: hs at denx.de

[U-Boot] [PATCH u-boot-marvell v2 01/15] arm: mvebu: turris_omnia: remove redundant code

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> The i2c slave disabling is done by mvtwsi driver and is not needed here.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 02/15] arm: mvebu: turris_omnia: add XHCI to defconfig

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Add XHCI_HOST and XHCI_MVEBU to defconfig, so that user's can by default
> boot from USB on Turris Omnia.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 03/15] arm: mvebu: turris_omnia: use AHCI and SATA driver model

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Enable AHCI, SCSI and SATA for compliance with the driver model
> migration.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 04/15] arm: mvebu: turris_omnia: remove legacy macros from board header

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> These are not needed if MMC and SCSI DM drivers are used.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 05/15] arm: mvebu: turris_omnia: move I2C dependencies to Kconfig

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> The I2C dependencies are defined in include/configs/turris_omnia.h,
> because Turris Omnia won't boot correctly without I2C support.
> 
> Move these dependencies to Kconfig, so that they are selected if Turris
> Omnia is selected as target.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 06/15] arm: mvebu: turris_omnia: add SCSI as boot target

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> If SCSI is enabled, U-Boot should try to boot also from SCSI device on
> Turris Omnia.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 07/15] arm: mvebu: turris_omnia: refactor I2C accessing code

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Refactor code which accesses the microcontroller and EEPROM via I2C.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 08/15] arm: mvebu: turris_omnia: fix checkpatch warnings

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 09/15] arm: mvebu: turris_omnia: move ATSHA204A from defconfig to Kconfig

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> This driver is required for Turris Omnia to read ethernet addresses.
> Move the dependency from turris_omnia_defconfig to Kconfig.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 10/15] arm: mvebu: turris_omnia: refactor more code

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Refactor RAM size reading from EEPROM in preparation for next patch.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 11/15] arm: mvebu: turris_omnia: print board info as Turris Mox

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Unify the way how Omnia and Mox print board information (RAM size and
> serial number).
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 12/15] arm: mvebu: turris_*: remove watchdog include

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> Since board watchdog is now unified and not handled in board files,
> remove the unnecessary includes.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 13/15] arm: mvebu: turris_omnia: fix regdomain env var setting

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> The regdomain environment variable is set according to value read from
> EEPROM. This has to be done in board_late_init, after the environment
> variables are read from SPI. Select CONFIG_BOARD_LATE_INIT in Kconfig
> for the Turris Omnia target.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>

Reviewed-by: Stefan Roese <sr@denx.de>

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Stefan Roese]

On 30.04.19 03:48, Marek Behún wrote:
> There is a Factory RESET button on the back side of the Turris Omnia
> router. When user presses this button before powering the device up and
> keeps it pressed, the microcontroller prevents the main CPU from booting
> and counts how long the RESET button is being pressed (and indicates
> this by lighting up front LEDs).
> 
> The idea behind this is that the user can boot the device into several
> Factory RESET modes.
> 
> This patch adds support for U-Boot to read into which Factory RESET mode
> the user booted the device. The value is an integer stored into the
> omnia_reset environment variable. It is 0 if the button was not pressed
> at all during power up, otherwise it is the number identifying the
> Factory RESET mode.
> 
> This patch also adds support for configuring (via Kconfig) if the
> bootcmd environment variable should be overwritten if this Factory RESET
> button was pressed during device powerup, and if this configuration
> option is enabled, the value by which bootcmd should be overwritten with
> is also a configurable option. The default value sets the colors of all
> the LEDs on the front panel to green, then loads the rescue system image
> from the SPI flash memory and then boots it.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> ---
>   arch/arm/mach-mvebu/Kconfig              | 43 ++++++++++++++++++++++++
>   board/CZ.NIC/turris_omnia/turris_omnia.c | 23 +++++++++++++
>   2 files changed, 66 insertions(+)
> 
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index fc29c3b084..4229a505d1 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -116,6 +116,7 @@ config TARGET_DB_88F6820_AMC
>   config TARGET_TURRIS_OMNIA
>   	bool "Support Turris Omnia"
>   	select 88F6820
> +	select BOARD_LATE_INIT
>   	select DM_I2C
>   	select I2C_MUX
>   	select I2C_MUX_PCA954x
> @@ -165,6 +166,48 @@ config TARGET_DB_XC3_24G4XG
>   
>   endchoice
>   
> +if TARGET_TURRIS_OMNIA
> +
> +config TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
> +	bool "Turris Omnia RESET button overwrites bootcmd"
> +	default y
> +	help
> +	  There is a RESET button on the back side of the Turris Omnia router,
> +	  which is read by the microcontroller before the main CPU is booted.
> +	  If this button is pressed during device poweron, the CPU is only
> +	  booted after the button is released.
> +
> +	  The CPU can then read how long the RESET button was pressed (in time
> +	  intervals of cca 2 seconds, at most 12 different values), and U-Boot
> +	  stores this value into omnia_reset environment variable.
> +	  The microcontroller also lights up one front LED every time interval,
> +	  so that users can see the value they are forcing.
> +
> +	  If this option is enabled, the board code will also overwrite the
> +	  bootcmd variable with a constant configurable in this configuration
> +	  (config TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE) if the RESET button was
> +	  pressed for at least one time interval.
> +
> +	  Otherwise only the omnia_reset environment variable is set.
> +
> +config TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE
> +	string "Turris Omnia RESET button bootcmd value"
> +	default "i2c dev 2; i2c mw 0x2a.1 0x3 0x1c 1; i2c mw 0x2a.1 0x4 0x1c 1; mw.l 0x01000000 0x00ff000c; i2c write 0x01000000 0x2a.1 0x5 4 -s; setenv bootargs \\\"$bootargs omniarescue=$omnia_reset\\\"; sf probe; sf read 0x1000000 0x100000 0x700000; bootm 0x1000000; bootz 0x1000000"
> +	depends on TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
> +	help
> +	  If the RESET button is pressed during device poweron and released at
> +	  least after cca 2 seconds, the bootcmd will be overwritten with this
> +	  value.
> +
> +	  You can use the omnia_reset environment variable in this command to
> +	  detect how long the reset button was pressed (or pass this value to
> +	  Linux as a boot parameter).
> +
> +	  The default value of this command set the front LEDs to green color
> +	  and then tries to boot rescue system from SPI memory.
> +
> +endif

I fail to see a real reason to introduce these Kconfig options. Is
TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD enabled for your board? If not
it just adds dead code, as no other board will ever enable it. So do
you plan to add 2 Omnia build targets, one with and one w/o this
option enabled? Or what is your plan here?

Thanks,
Stefan

> +
>   config SYS_BOARD
>   	default "clearfog" if TARGET_CLEARFOG
>   	default "helios4" if TARGET_HELIOS4
> diff --git a/board/CZ.NIC/turris_omnia/turris_omnia.c b/board/CZ.NIC/turris_omnia/turris_omnia.c
> index af43ee23d9..91fce6370c 100644
> --- a/board/CZ.NIC/turris_omnia/turris_omnia.c
> +++ b/board/CZ.NIC/turris_omnia/turris_omnia.c
> @@ -328,6 +328,28 @@ static int set_regdomain(void)
>   	printf("Regdomain set to %s\n", rd);
>   	return env_set("regdomain", rd);
>   }
> +
> +static void handle_reset_button(void)
> +{
> +	int ret;
> +	u8 reset_status;
> +
> +	ret = omnia_mcu_read(CMD_GET_RESET, &reset_status, 1);
> +	if (ret) {
> +		printf("omnia_mcu_read failed: %i, reset status unknown!\n",
> +		       ret);
> +		return;
> +	}
> +
> +	env_set_ulong("omnia_reset", reset_status);
> +
> +#ifdef CONFIG_TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD
> +	if (reset_status) {
> +		printf("RESET button was pressed, overwriting bootcmd!\n");
> +		env_set("bootcmd", CONFIG_TURRIS_OMNIA_RSTBTN_BOOTCMD_VALUE);
> +	}
> +#endif
> +}
>   #endif
>   
>   int board_early_init_f(void)
> @@ -373,6 +395,7 @@ int board_late_init(void)
>   {
>   #ifndef CONFIG_SPL_BUILD
>   	set_regdomain();
> +	handle_reset_button();
>   #endif
>   
>   	return 0;
> 

Viele Grüße,
Stefan

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de

[U-Boot] [PATCH u-boot-marvell v2.1 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Stefan Roese]

On 01.05.19 23:09, Marek Behún wrote:
> The twsi_wait function reads the control register for interrupt flag,
> and if interrupt flag is present, it immediately reads status register.
> 
> On our device this sometimes causes bad value being read from status
> register, as if the value was not yet updated.
> 
> My theory is that the controller does approximately this:
>    1. sets interrupt flag in control register,
>    2. sets the value of status register,
>    3. causes an interrupt
> 
> In U-Boot we do not use interrupts, so I think that it is possible that
> sometimes the status register in the twsi_wait function is read between
> points 1 and 2.
> 
> The bug does not appear if I add a small delay before reading status
> register.
> 
> Wait 100ns (which in U-Boot currently means 1 us, because ndelay(i)
> function calls udelay(DIV_ROUND_UP(i, 1000))) before reading the status
> register.
> 
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> Acked-by: Heiko Schocher <hs@denx.de>
> Cc: Mario Six <mario.six@gdsys.cc>
> Cc: Stefan Roese <sr@denx.de>
> Cc: Baruch Siach <baruch@tkos.co.il>
> ---
>   drivers/i2c/mvtwsi.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/i2c/mvtwsi.c b/drivers/i2c/mvtwsi.c
> index 74ac0a4aa7..0a2dafcec6 100644
> --- a/drivers/i2c/mvtwsi.c
> +++ b/drivers/i2c/mvtwsi.c
> @@ -271,6 +271,17 @@ static int twsi_wait(struct mvtwsi_registers *twsi, int expected_status,
>   	do {
>   		control = readl(&twsi->control);
>   		if (control & MVTWSI_CONTROL_IFLG) {
> +			/*
> +			 * On Armada 38x it seems that the controller works as
> +			 * if it first set the MVTWSI_CONTROL_IFLAG in the
> +			 * control register and only after that it changed the
> +			 * status register.
> +			 * This sometimes caused weird bugs which only appeared
> +			 * on selected I2C speeds and even then only sometimes.
> +			 * We therefore add here a simple ndealy(100), which
> +			 * seems to fix this weird bug.
> +			 */
> +			ndelay(100);
>   			status = readl(&twsi->status);
>   			if (status == expected_status)
>   				return 0;
> 

This still looks a bit strange. Looking at the Linux driver, there
is no delay after reading the control register. But its using
interrupts and therefore an implicit delay is added before this
interrupt service routine is called (instead of the busy loop here
in the U-Boot driver).

So since I don't have a better idea:

Reviewed-by: Stefan Roese <sr@denx.de>

BTW: Whats the value of "tick" in twsi_wait() in your case?

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2.1 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Marek Behun]

> This still looks a bit strange. Looking at the Linux driver, there
> is no delay after reading the control register. But its using
> interrupts and therefore an implicit delay is added before this
> interrupt service routine is called (instead of the busy loop here
> in the U-Boot driver).

Exactly my opinion as well.

> BTW: Whats the value of "tick" in twsi_wait() in your case?

requested I2C freq is 100000 Hz, actual 97656 Hz (nearest lower
possible). This calculates the tick to 10340 ns with calc_tick, and
u-boot sleeps for 11 ms (DIV_ROUND_UP).

When tick was 10 ms this bug did not occur, because of the different
timing when the control value was read it already was set for a while
by the controller, it seems.

Btw should I sent these first 14 patches with Reviewed-by tags?

Marek

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Marek Behun]

On Thu, 2 May 2019 08:10:36 +0200
Stefan Roese <sr@denx.de> wrote:

> I fail to see a real reason to introduce these Kconfig options. Is
> TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD enabled for your board? If not
> it just adds dead code, as no other board will ever enable it. So do
> you plan to add 2 Omnia build targets, one with and one w/o this
> option enabled? Or what is your plan here?
> 
> Thanks,
> Stefan

My idea was that the users should be able to disable this functionality,
if they are compiling u-boot themselves, but we are going to ship
Omnias with this config enabled.

I can of course remove the Kconfig options and enable this reset button
handling all times.

Marek

[U-Boot] [PATCH u-boot-marvell v2.1 15/15] i2c: mvtwsi: fix reading status register after interrupt

[Stefan Roese]

On 02.05.19 11:36, Marek Behun wrote:
>> This still looks a bit strange. Looking at the Linux driver, there
>> is no delay after reading the control register. But its using
>> interrupts and therefore an implicit delay is added before this
>> interrupt service routine is called (instead of the busy loop here
>> in the U-Boot driver).
> 
> Exactly my opinion as well.
> 
>> BTW: Whats the value of "tick" in twsi_wait() in your case?
> 
> requested I2C freq is 100000 Hz, actual 97656 Hz (nearest lower
> possible). This calculates the tick to 10340 ns with calc_tick, and
> u-boot sleeps for 11 ms (DIV_ROUND_UP).
> 
> When tick was 10 ms this bug did not occur, because of the different
> timing when the control value was read it already was set for a while
> by the controller, it seems.
> 
> Btw should I sent these first 14 patches with Reviewed-by tags?

No need for that, thanks. Patchwork will pick up the tags automatically.

Next time, please switch to v3 instead of v2.1 though.

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Stefan Roese]

On 02.05.19 11:39, Marek Behun wrote:
> On Thu, 2 May 2019 08:10:36 +0200
> Stefan Roese <sr@denx.de> wrote:
> 
>> I fail to see a real reason to introduce these Kconfig options. Is
>> TURRIS_OMNIA_RSTBTN_OVERWRITE_BOOTCMD enabled for your board? If not
>> it just adds dead code, as no other board will ever enable it. So do
>> you plan to add 2 Omnia build targets, one with and one w/o this
>> option enabled? Or what is your plan here?
>>
>> Thanks,
>> Stefan
> 
> My idea was that the users should be able to disable this functionality,
> if they are compiling u-boot themselves, but we are going to ship
> Omnias with this config enabled.

Understood, thanks.
  
> I can of course remove the Kconfig options and enable this reset button
> handling all times.

Please do so. If someone whats to disable this functionality or change
the reset button bootcmd, then he/she/it must do some changes (defconfig
or code).

Thanks,
Stefan

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Marek Behún]

On Thu, 2 May 2019 11:43:12 +0200
Stefan Roese <sr@denx.de> wrote:

> Please do so. If someone whats to disable this functionality or change
> the reset button bootcmd, then he/she/it must do some changes
> (defconfig or code).

So should I remove the options from Kconfig or enable them by default?

BTW: We are going to ship omnia with several other options enabled?
Should I push them also to defconfig?

They are:

CONFIG_FIT=y
CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
CONFIG_FIT_VERBOSE=y
CONFIG_CMD_LZMADEC=y
CONFIG_CMD_AES=y
CONFIG_CMD_HASH=y
CONFIG_CMD_SHA1SUM=y

Marek

[U-Boot] [PATCH u-boot-marvell v2 14/15] arm: mvebu: turris_omnia: add RESET button handling

[Stefan Roese]

On 02.05.19 13:53, Marek Behún wrote:
> On Thu, 2 May 2019 11:43:12 +0200
> Stefan Roese <sr@denx.de> wrote:
> 
>> Please do so. If someone whats to disable this functionality or change
>> the reset button bootcmd, then he/she/it must do some changes
>> (defconfig or code).
> 
> So should I remove the options from Kconfig or enable them by default?

Yes.
  
> BTW: We are going to ship omnia with several other options enabled?
> Should I push them also to defconfig?

Yes please. Or why would it make sense to have a stripped down version
of this board port in mainline?
  
> They are:
> 
> CONFIG_FIT=y
> CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
> CONFIG_FIT_VERBOSE=y
> CONFIG_CMD_LZMADEC=y
> CONFIG_CMD_AES=y
> CONFIG_CMD_HASH=y
> CONFIG_CMD_SHA1SUM=y
> 
> Marek
> 

Thanks,
Stefan