[PATCH 0/4] arm64: dts: meson: fix BPI-M5 and add BPI-M2-PRO

[PATCH 0/4] arm64: dts: meson: fix BPI-M5 and add BPI-M2-PRO

[Christian Hewitt]

The first patch in this series fixes an SD card (re)boot issue on the
BPI-M5. Susequent patches convert the (fixed) dts into a common dtsi
to support the addition of BPI-M2-PRO which is based upon the BPI-M5
board design.

Christian Hewitt (4):
  arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
  arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi
  dt-bindings: arm: amlogic: add support for BananaPi M2-Pro
  arm64: dts: meson: add support for BananaPi M2-Pro

 .../devicetree/bindings/arm/amlogic.yaml      |   1 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts |  98 ++++
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 5 files changed, 536 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

-- 
2.34.1

[PATCH 0/4] arm64: dts: meson: fix BPI-M5 and add BPI-M2-PRO

[Christian Hewitt]

The first patch in this series fixes an SD card (re)boot issue on the
BPI-M5. Susequent patches convert the (fixed) dts into a common dtsi
to support the addition of BPI-M2-PRO which is based upon the BPI-M5
board design.

Christian Hewitt (4):
  arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
  arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi
  dt-bindings: arm: amlogic: add support for BananaPi M2-Pro
  arm64: dts: meson: add support for BananaPi M2-Pro

 .../devicetree/bindings/arm/amlogic.yaml      |   1 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts |  98 ++++
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 5 files changed, 536 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 0/4] arm64: dts: meson: fix BPI-M5 and add BPI-M2-PRO

[Christian Hewitt]

The first patch in this series fixes an SD card (re)boot issue on the
BPI-M5. Susequent patches convert the (fixed) dts into a common dtsi
to support the addition of BPI-M2-PRO which is based upon the BPI-M5
board design.

Christian Hewitt (4):
  arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN
  arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi
  dt-bindings: arm: amlogic: add support for BananaPi M2-Pro
  arm64: dts: meson: add support for BananaPi M2-Pro

 .../devicetree/bindings/arm/amlogic.yaml      |   1 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts |  98 ++++
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 5 files changed, 536 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 1/4] arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN

[Christian Hewitt]

For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).

This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).

Fixes 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 028220ed45ad..3c1267a7ffef 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -123,7 +123,7 @@ vddio_c: regulator-vddio_c {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
-- 
2.34.1

[PATCH 1/4] arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN

[Christian Hewitt]

For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).

This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).

Fixes 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 028220ed45ad..3c1267a7ffef 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -123,7 +123,7 @@ vddio_c: regulator-vddio_c {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/4] arm64: dts: meson: bananapi-m5: switch VDDIO_C pin to OPEN_DRAIN

[Christian Hewitt]

For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).

This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).

Fixes 976e920183e4 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 028220ed45ad..3c1267a7ffef 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -123,7 +123,7 @@ vddio_c: regulator-vddio_c {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 2/4] arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi

[Christian Hewitt]

Convert the BPI-M5 dts into meson-sm1-bananapi.dtsi to support the
addition of new boards based on the same design.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 2 files changed, 436 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 3c1267a7ffef..34b3238ee0a0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -6,10 +6,7 @@
 
 /dts-v1/;
 
-#include "meson-sm1.dtsi"
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/input/linux-event-codes.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-sm1-bananapi.dtsi"
 #include <dt-bindings/sound/meson-g12a-toacodec.h>
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
@@ -17,28 +14,6 @@ / {
 	compatible = "bananapi,bpi-m5", "amlogic,sm1";
 	model = "Banana Pi BPI-M5";
 
-	adc_keys {
-		compatible = "adc-keys";
-		io-channels = <&saradc 2>;
-		io-channel-names = "buttons";
-		keyup-threshold-microvolt = <1800000>;
-
-		key {
-			label = "SW3";
-			linux,code = <BTN_3>;
-			press-threshold-microvolt = <1700000>;
-		};
-	};
-
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	/* TOFIX: handle CVBS_DET on SARADC channel 0 */
 	cvbs-connector {
 		compatible = "composite-video-connector";
@@ -50,150 +25,6 @@ cvbs_connector_in: endpoint {
 		};
 	};
 
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		key {
-			label = "SW1";
-			linux,code = <BTN_1>;
-			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
-			interrupt-parent = <&gpio_intc>;
-			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
-		};
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-green {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
-		};
-
-		led-blue {
-			color = <LED_COLOR_ID_BLUE>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_1v8: regulator-emmc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "EMMC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	dc_in: regulator-dc_in {
-		compatible = "regulator-fixed";
-		regulator-name = "DC_IN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vddio_c: regulator-vddio_c {
-		compatible = "regulator-gpio";
-		regulator-name = "VDDIO_C";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-
-		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
-		gpios-states = <1>;
-
-		states = <1800000 0>,
-			 <3300000 1>;
-	};
-
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		regulator-always-on;
-	};
-
-	vddcpu: regulator-vddcpu {
-		/*
-		 * SY8120B1ABC DC/DC Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU";
-		regulator-min-microvolt = <690000>;
-		regulator-max-microvolt = <1050000>;
-
-		pwm-supply = <&dc_in>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	/* USB Hub Power Enable */
-	vl_pwr_en: regulator-vl_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "VL_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&dc_in>;
-
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "BPI-M5";
@@ -319,68 +150,17 @@ &acodec {
 	status = "okay";
 };
 
-&arb {
-	status = "okay";
-};
 
 &clkc_audio {
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU1_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu2 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU2_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu3 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU3_CLK>;
-	clock-latency = <50000>;
-};
-
 &cvbs_vdac_port {
 	cvbs_vdac_out: endpoint {
 		remote-endpoint = <&cvbs_connector_in>;
 	};
 };
 
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii-txid";
-	phy-handle = <&external_phy>;
-};
-
 &frddr_a {
 	status = "okay";
 };
@@ -393,192 +173,6 @@ &frddr_c {
 	status = "okay";
 };
 
-&gpio {
-	gpio-line-names =
-		/* GPIOZ */
-		"ETH_MDIO", /* GPIOZ_0 */
-		"ETH_MDC", /* GPIOZ_1 */
-		"ETH_RXCLK", /* GPIOZ_2 */
-		"ETH_RX_DV", /* GPIOZ_3 */
-		"ETH_RXD0", /* GPIOZ_4 */
-		"ETH_RXD1", /* GPIOZ_5 */
-		"ETH_RXD2", /* GPIOZ_6 */
-		"ETH_RXD3", /* GPIOZ_7 */
-		"ETH_TXCLK", /* GPIOZ_8 */
-		"ETH_TXEN", /* GPIOZ_9 */
-		"ETH_TXD0", /* GPIOZ_10 */
-		"ETH_TXD1", /* GPIOZ_11 */
-		"ETH_TXD2", /* GPIOZ_12 */
-		"ETH_TXD3", /* GPIOZ_13 */
-		"ETH_INTR", /* GPIOZ_14 */
-		"ETH_NRST", /* GPIOZ_15 */
-		/* GPIOH */
-		"HDMI_SDA", /* GPIOH_0 */
-		"HDMI_SCL", /* GPIOH_1 */
-		"HDMI_HPD", /* GPIOH_2 */
-		"HDMI_CEC", /* GPIOH_3 */
-		"VL-RST_N", /* GPIOH_4 */
-		"CON1-P36", /* GPIOH_5 */
-		"VL-PWREN", /* GPIOH_6 */
-		"WiFi_3V3_1V8", /* GPIOH_7 */
-		"TFLASH_VDD_EN", /* GPIOH_8 */
-		/* BOOT */
-		"eMMC_D0", /* BOOT_0 */
-		"eMMC_D1", /* BOOT_1 */
-		"eMMC_D2", /* BOOT_2 */
-		"eMMC_D3", /* BOOT_3 */
-		"eMMC_D4", /* BOOT_4 */
-		"eMMC_D5", /* BOOT_5 */
-		"eMMC_D6", /* BOOT_6 */
-		"eMMC_D7", /* BOOT_7 */
-		"eMMC_CLK", /* BOOT_8 */
-		"",
-		"eMMC_CMD", /* BOOT_10 */
-		"",
-		"eMMC_RST#", /* BOOT_12 */
-		"eMMC_DS", /* BOOT_13 */
-		"", "",
-		/* GPIOC */
-		"SD_D0_B", /* GPIOC_0 */
-		"SD_D1_B", /* GPIOC_1 */
-		"SD_D2_B", /* GPIOC_2 */
-		"SD_D3_B", /* GPIOC_3 */
-		"SD_CLK_B", /* GPIOC_4 */
-		"SD_CMD_B", /* GPIOC_5 */
-		"CARD_EN_DET", /* GPIOC_6 */
-		"",
-		/* GPIOA */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "",
-		"CON1-P27", /* GPIOA_14 */
-		"CON1-P28", /* GPIOA_15 */
-		/* GPIOX */
-		"CON1-P16", /* GPIOX_0 */
-		"CON1-P18", /* GPIOX_1 */
-		"CON1-P22", /* GPIOX_2 */
-		"CON1-P11", /* GPIOX_3 */
-		"CON1-P13", /* GPIOX_4 */
-		"CON1-P07", /* GPIOX_5 */
-		"CON1-P33", /* GPIOX_6 */
-		"CON1-P15", /* GPIOX_7 */
-		"CON1-P19", /* GPIOX_8 */
-		"CON1-P21", /* GPIOX_9 */
-		"CON1-P24", /* GPIOX_10 */
-		"CON1-P23", /* GPIOX_11 */
-		"CON1-P08", /* GPIOX_12 */
-		"CON1-P10", /* GPIOX_13 */
-		"CON1-P29", /* GPIOX_14 */
-		"CON1-P31", /* GPIOX_15 */
-		"CON1-P26", /* GPIOX_16 */
-		"CON1-P03", /* GPIOX_17 */
-		"CON1-P05", /* GPIOX_18 */
-		"CON1-P32"; /* GPIOX_19 */
-
-	/*
-	 * WARNING: The USB Hub on the BPI-M5 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&gpio_ao {
-	gpio-line-names =
-		/* GPIOAO */
-		"DEBUG TX", /* GPIOAO_0 */
-		"DEBUG RX", /* GPIOAO_1 */
-		"SYS_LED2", /* GPIOAO_2 */
-		"UPDATE_KEY", /* GPIOAO_3 */
-		"CON1-P40", /* GPIOAO_4 */
-		"IR_IN", /* GPIOAO_5 */
-		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
-		"CON1-P35", /* GPIOAO_7 */
-		"CON1-P12", /* GPIOAO_8 */
-		"CON1-P37", /* GPIOAO_9 */
-		"CON1-P38", /* GPIOAO_10 */
-		"SYS_LED", /* GPIOAO_11 */
-		/* GPIOE */
-		"VDDEE_PWM", /* GPIOE_0 */
-		"VDDCPU_PWM", /* GPIOE_1 */
-		"TF_PWR_EN"; /* GPIOE_2 */
-};
-
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&dc_in>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-	vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	/* TOFIX: SD card is barely usable in SDR modes */
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&vddio_c>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&emmc_1v8>;
-};
-
 &tdmif_b {
 	status = "okay";
 };
@@ -626,22 +220,3 @@ &toddr_b {
 &toddr_c {
 	status = "okay";
 };
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-};
-
-&usb2_phy0 {
-	phy-supply = <&dc_in>;
-};
-
-&usb2_phy1 {
-	/* Enable the hub which is connected to this port */
-	phy-supply = <&vl_pwr_en>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
new file mode 100644
index 000000000000..c914f1148185
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
@@ -0,0 +1,435 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	adc_keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 2>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+
+		key {
+			label = "SW3";
+			linux,code = <BTN_3>;
+			press-threshold-microvolt = <1700000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key {
+			label = "SW1";
+			linux,code = <BTN_1>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio_intc>;
+			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddio_c: regulator-vddio_c {
+		compatible = "regulator-gpio";
+		regulator-name = "VDDIO_C";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+
+		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
+		gpios-states = <1>;
+
+		states = <1800000 0>,
+			 <3300000 1>;
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * SY8120B1ABC DC/DC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		pwm-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	/* USB Hub Power Enable */
+	vl_pwr_en: regulator-vl_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "VL_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+};
+
+&gpio {
+	gpio-line-names =
+		/* GPIOZ */
+		"ETH_MDIO", /* GPIOZ_0 */
+		"ETH_MDC", /* GPIOZ_1 */
+		"ETH_RXCLK", /* GPIOZ_2 */
+		"ETH_RX_DV", /* GPIOZ_3 */
+		"ETH_RXD0", /* GPIOZ_4 */
+		"ETH_RXD1", /* GPIOZ_5 */
+		"ETH_RXD2", /* GPIOZ_6 */
+		"ETH_RXD3", /* GPIOZ_7 */
+		"ETH_TXCLK", /* GPIOZ_8 */
+		"ETH_TXEN", /* GPIOZ_9 */
+		"ETH_TXD0", /* GPIOZ_10 */
+		"ETH_TXD1", /* GPIOZ_11 */
+		"ETH_TXD2", /* GPIOZ_12 */
+		"ETH_TXD3", /* GPIOZ_13 */
+		"ETH_INTR", /* GPIOZ_14 */
+		"ETH_NRST", /* GPIOZ_15 */
+		/* GPIOH */
+		"HDMI_SDA", /* GPIOH_0 */
+		"HDMI_SCL", /* GPIOH_1 */
+		"HDMI_HPD", /* GPIOH_2 */
+		"HDMI_CEC", /* GPIOH_3 */
+		"VL-RST_N", /* GPIOH_4 */
+		"CON1-P36", /* GPIOH_5 */
+		"VL-PWREN", /* GPIOH_6 */
+		"WiFi_3V3_1V8", /* GPIOH_7 */
+		"TFLASH_VDD_EN", /* GPIOH_8 */
+		/* BOOT */
+		"eMMC_D0", /* BOOT_0 */
+		"eMMC_D1", /* BOOT_1 */
+		"eMMC_D2", /* BOOT_2 */
+		"eMMC_D3", /* BOOT_3 */
+		"eMMC_D4", /* BOOT_4 */
+		"eMMC_D5", /* BOOT_5 */
+		"eMMC_D6", /* BOOT_6 */
+		"eMMC_D7", /* BOOT_7 */
+		"eMMC_CLK", /* BOOT_8 */
+		"",
+		"eMMC_CMD", /* BOOT_10 */
+		"",
+		"eMMC_RST#", /* BOOT_12 */
+		"eMMC_DS", /* BOOT_13 */
+		"", "",
+		/* GPIOC */
+		"SD_D0_B", /* GPIOC_0 */
+		"SD_D1_B", /* GPIOC_1 */
+		"SD_D2_B", /* GPIOC_2 */
+		"SD_D3_B", /* GPIOC_3 */
+		"SD_CLK_B", /* GPIOC_4 */
+		"SD_CMD_B", /* GPIOC_5 */
+		"CARD_EN_DET", /* GPIOC_6 */
+		"",
+		/* GPIOA */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"CON1-P27", /* GPIOA_14 */
+		"CON1-P28", /* GPIOA_15 */
+		/* GPIOX */
+		"CON1-P16", /* GPIOX_0 */
+		"CON1-P18", /* GPIOX_1 */
+		"CON1-P22", /* GPIOX_2 */
+		"CON1-P11", /* GPIOX_3 */
+		"CON1-P13", /* GPIOX_4 */
+		"CON1-P07", /* GPIOX_5 */
+		"CON1-P33", /* GPIOX_6 */
+		"CON1-P15", /* GPIOX_7 */
+		"CON1-P19", /* GPIOX_8 */
+		"CON1-P21", /* GPIOX_9 */
+		"CON1-P24", /* GPIOX_10 */
+		"CON1-P23", /* GPIOX_11 */
+		"CON1-P08", /* GPIOX_12 */
+		"CON1-P10", /* GPIOX_13 */
+		"CON1-P29", /* GPIOX_14 */
+		"CON1-P31", /* GPIOX_15 */
+		"CON1-P26", /* GPIOX_16 */
+		"CON1-P03", /* GPIOX_17 */
+		"CON1-P05", /* GPIOX_18 */
+		"CON1-P32"; /* GPIOX_19 */
+
+	/*
+	 * WARNING: The USB Hub needs a reset signal to be turned high in
+	 * order to be detected by the USB Controller. This signal should
+	 * be handled by a USB specific power sequence to reset the Hub
+	 * when the USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&gpio_ao {
+	gpio-line-names =
+		/* GPIOAO */
+		"DEBUG TX", /* GPIOAO_0 */
+		"DEBUG RX", /* GPIOAO_1 */
+		"SYS_LED2", /* GPIOAO_2 */
+		"UPDATE_KEY", /* GPIOAO_3 */
+		"CON1-P40", /* GPIOAO_4 */
+		"IR_IN", /* GPIOAO_5 */
+		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
+		"CON1-P35", /* GPIOAO_7 */
+		"CON1-P12", /* GPIOAO_8 */
+		"CON1-P37", /* GPIOAO_9 */
+		"CON1-P38", /* GPIOAO_10 */
+		"SYS_LED", /* GPIOAO_11 */
+		/* GPIOE */
+		"VDDEE_PWM", /* GPIOE_0 */
+		"VDDCPU_PWM", /* GPIOE_1 */
+		"TF_PWR_EN"; /* GPIOE_2 */
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&dc_in>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	/* TOFIX: SD card is barely usable in SDR modes */
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&vddio_c>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&dc_in>;
+};
+
+&usb2_phy1 {
+	/* Enable the hub which is connected to this port */
+	phy-supply = <&vl_pwr_en>;
+};
-- 
2.34.1

[PATCH 2/4] arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi

[Christian Hewitt]

Convert the BPI-M5 dts into meson-sm1-bananapi.dtsi to support the
addition of new boards based on the same design.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 2 files changed, 436 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 3c1267a7ffef..34b3238ee0a0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -6,10 +6,7 @@
 
 /dts-v1/;
 
-#include "meson-sm1.dtsi"
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/input/linux-event-codes.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-sm1-bananapi.dtsi"
 #include <dt-bindings/sound/meson-g12a-toacodec.h>
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
@@ -17,28 +14,6 @@ / {
 	compatible = "bananapi,bpi-m5", "amlogic,sm1";
 	model = "Banana Pi BPI-M5";
 
-	adc_keys {
-		compatible = "adc-keys";
-		io-channels = <&saradc 2>;
-		io-channel-names = "buttons";
-		keyup-threshold-microvolt = <1800000>;
-
-		key {
-			label = "SW3";
-			linux,code = <BTN_3>;
-			press-threshold-microvolt = <1700000>;
-		};
-	};
-
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	/* TOFIX: handle CVBS_DET on SARADC channel 0 */
 	cvbs-connector {
 		compatible = "composite-video-connector";
@@ -50,150 +25,6 @@ cvbs_connector_in: endpoint {
 		};
 	};
 
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		key {
-			label = "SW1";
-			linux,code = <BTN_1>;
-			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
-			interrupt-parent = <&gpio_intc>;
-			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
-		};
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-green {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
-		};
-
-		led-blue {
-			color = <LED_COLOR_ID_BLUE>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_1v8: regulator-emmc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "EMMC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	dc_in: regulator-dc_in {
-		compatible = "regulator-fixed";
-		regulator-name = "DC_IN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vddio_c: regulator-vddio_c {
-		compatible = "regulator-gpio";
-		regulator-name = "VDDIO_C";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-
-		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
-		gpios-states = <1>;
-
-		states = <1800000 0>,
-			 <3300000 1>;
-	};
-
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		regulator-always-on;
-	};
-
-	vddcpu: regulator-vddcpu {
-		/*
-		 * SY8120B1ABC DC/DC Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU";
-		regulator-min-microvolt = <690000>;
-		regulator-max-microvolt = <1050000>;
-
-		pwm-supply = <&dc_in>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	/* USB Hub Power Enable */
-	vl_pwr_en: regulator-vl_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "VL_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&dc_in>;
-
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "BPI-M5";
@@ -319,68 +150,17 @@ &acodec {
 	status = "okay";
 };
 
-&arb {
-	status = "okay";
-};
 
 &clkc_audio {
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU1_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu2 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU2_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu3 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU3_CLK>;
-	clock-latency = <50000>;
-};
-
 &cvbs_vdac_port {
 	cvbs_vdac_out: endpoint {
 		remote-endpoint = <&cvbs_connector_in>;
 	};
 };
 
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii-txid";
-	phy-handle = <&external_phy>;
-};
-
 &frddr_a {
 	status = "okay";
 };
@@ -393,192 +173,6 @@ &frddr_c {
 	status = "okay";
 };
 
-&gpio {
-	gpio-line-names =
-		/* GPIOZ */
-		"ETH_MDIO", /* GPIOZ_0 */
-		"ETH_MDC", /* GPIOZ_1 */
-		"ETH_RXCLK", /* GPIOZ_2 */
-		"ETH_RX_DV", /* GPIOZ_3 */
-		"ETH_RXD0", /* GPIOZ_4 */
-		"ETH_RXD1", /* GPIOZ_5 */
-		"ETH_RXD2", /* GPIOZ_6 */
-		"ETH_RXD3", /* GPIOZ_7 */
-		"ETH_TXCLK", /* GPIOZ_8 */
-		"ETH_TXEN", /* GPIOZ_9 */
-		"ETH_TXD0", /* GPIOZ_10 */
-		"ETH_TXD1", /* GPIOZ_11 */
-		"ETH_TXD2", /* GPIOZ_12 */
-		"ETH_TXD3", /* GPIOZ_13 */
-		"ETH_INTR", /* GPIOZ_14 */
-		"ETH_NRST", /* GPIOZ_15 */
-		/* GPIOH */
-		"HDMI_SDA", /* GPIOH_0 */
-		"HDMI_SCL", /* GPIOH_1 */
-		"HDMI_HPD", /* GPIOH_2 */
-		"HDMI_CEC", /* GPIOH_3 */
-		"VL-RST_N", /* GPIOH_4 */
-		"CON1-P36", /* GPIOH_5 */
-		"VL-PWREN", /* GPIOH_6 */
-		"WiFi_3V3_1V8", /* GPIOH_7 */
-		"TFLASH_VDD_EN", /* GPIOH_8 */
-		/* BOOT */
-		"eMMC_D0", /* BOOT_0 */
-		"eMMC_D1", /* BOOT_1 */
-		"eMMC_D2", /* BOOT_2 */
-		"eMMC_D3", /* BOOT_3 */
-		"eMMC_D4", /* BOOT_4 */
-		"eMMC_D5", /* BOOT_5 */
-		"eMMC_D6", /* BOOT_6 */
-		"eMMC_D7", /* BOOT_7 */
-		"eMMC_CLK", /* BOOT_8 */
-		"",
-		"eMMC_CMD", /* BOOT_10 */
-		"",
-		"eMMC_RST#", /* BOOT_12 */
-		"eMMC_DS", /* BOOT_13 */
-		"", "",
-		/* GPIOC */
-		"SD_D0_B", /* GPIOC_0 */
-		"SD_D1_B", /* GPIOC_1 */
-		"SD_D2_B", /* GPIOC_2 */
-		"SD_D3_B", /* GPIOC_3 */
-		"SD_CLK_B", /* GPIOC_4 */
-		"SD_CMD_B", /* GPIOC_5 */
-		"CARD_EN_DET", /* GPIOC_6 */
-		"",
-		/* GPIOA */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "",
-		"CON1-P27", /* GPIOA_14 */
-		"CON1-P28", /* GPIOA_15 */
-		/* GPIOX */
-		"CON1-P16", /* GPIOX_0 */
-		"CON1-P18", /* GPIOX_1 */
-		"CON1-P22", /* GPIOX_2 */
-		"CON1-P11", /* GPIOX_3 */
-		"CON1-P13", /* GPIOX_4 */
-		"CON1-P07", /* GPIOX_5 */
-		"CON1-P33", /* GPIOX_6 */
-		"CON1-P15", /* GPIOX_7 */
-		"CON1-P19", /* GPIOX_8 */
-		"CON1-P21", /* GPIOX_9 */
-		"CON1-P24", /* GPIOX_10 */
-		"CON1-P23", /* GPIOX_11 */
-		"CON1-P08", /* GPIOX_12 */
-		"CON1-P10", /* GPIOX_13 */
-		"CON1-P29", /* GPIOX_14 */
-		"CON1-P31", /* GPIOX_15 */
-		"CON1-P26", /* GPIOX_16 */
-		"CON1-P03", /* GPIOX_17 */
-		"CON1-P05", /* GPIOX_18 */
-		"CON1-P32"; /* GPIOX_19 */
-
-	/*
-	 * WARNING: The USB Hub on the BPI-M5 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&gpio_ao {
-	gpio-line-names =
-		/* GPIOAO */
-		"DEBUG TX", /* GPIOAO_0 */
-		"DEBUG RX", /* GPIOAO_1 */
-		"SYS_LED2", /* GPIOAO_2 */
-		"UPDATE_KEY", /* GPIOAO_3 */
-		"CON1-P40", /* GPIOAO_4 */
-		"IR_IN", /* GPIOAO_5 */
-		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
-		"CON1-P35", /* GPIOAO_7 */
-		"CON1-P12", /* GPIOAO_8 */
-		"CON1-P37", /* GPIOAO_9 */
-		"CON1-P38", /* GPIOAO_10 */
-		"SYS_LED", /* GPIOAO_11 */
-		/* GPIOE */
-		"VDDEE_PWM", /* GPIOE_0 */
-		"VDDCPU_PWM", /* GPIOE_1 */
-		"TF_PWR_EN"; /* GPIOE_2 */
-};
-
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&dc_in>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-	vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	/* TOFIX: SD card is barely usable in SDR modes */
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&vddio_c>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&emmc_1v8>;
-};
-
 &tdmif_b {
 	status = "okay";
 };
@@ -626,22 +220,3 @@ &toddr_b {
 &toddr_c {
 	status = "okay";
 };
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-};
-
-&usb2_phy0 {
-	phy-supply = <&dc_in>;
-};
-
-&usb2_phy1 {
-	/* Enable the hub which is connected to this port */
-	phy-supply = <&vl_pwr_en>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
new file mode 100644
index 000000000000..c914f1148185
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
@@ -0,0 +1,435 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	adc_keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 2>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+
+		key {
+			label = "SW3";
+			linux,code = <BTN_3>;
+			press-threshold-microvolt = <1700000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key {
+			label = "SW1";
+			linux,code = <BTN_1>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio_intc>;
+			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddio_c: regulator-vddio_c {
+		compatible = "regulator-gpio";
+		regulator-name = "VDDIO_C";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+
+		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
+		gpios-states = <1>;
+
+		states = <1800000 0>,
+			 <3300000 1>;
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * SY8120B1ABC DC/DC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		pwm-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	/* USB Hub Power Enable */
+	vl_pwr_en: regulator-vl_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "VL_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+};
+
+&gpio {
+	gpio-line-names =
+		/* GPIOZ */
+		"ETH_MDIO", /* GPIOZ_0 */
+		"ETH_MDC", /* GPIOZ_1 */
+		"ETH_RXCLK", /* GPIOZ_2 */
+		"ETH_RX_DV", /* GPIOZ_3 */
+		"ETH_RXD0", /* GPIOZ_4 */
+		"ETH_RXD1", /* GPIOZ_5 */
+		"ETH_RXD2", /* GPIOZ_6 */
+		"ETH_RXD3", /* GPIOZ_7 */
+		"ETH_TXCLK", /* GPIOZ_8 */
+		"ETH_TXEN", /* GPIOZ_9 */
+		"ETH_TXD0", /* GPIOZ_10 */
+		"ETH_TXD1", /* GPIOZ_11 */
+		"ETH_TXD2", /* GPIOZ_12 */
+		"ETH_TXD3", /* GPIOZ_13 */
+		"ETH_INTR", /* GPIOZ_14 */
+		"ETH_NRST", /* GPIOZ_15 */
+		/* GPIOH */
+		"HDMI_SDA", /* GPIOH_0 */
+		"HDMI_SCL", /* GPIOH_1 */
+		"HDMI_HPD", /* GPIOH_2 */
+		"HDMI_CEC", /* GPIOH_3 */
+		"VL-RST_N", /* GPIOH_4 */
+		"CON1-P36", /* GPIOH_5 */
+		"VL-PWREN", /* GPIOH_6 */
+		"WiFi_3V3_1V8", /* GPIOH_7 */
+		"TFLASH_VDD_EN", /* GPIOH_8 */
+		/* BOOT */
+		"eMMC_D0", /* BOOT_0 */
+		"eMMC_D1", /* BOOT_1 */
+		"eMMC_D2", /* BOOT_2 */
+		"eMMC_D3", /* BOOT_3 */
+		"eMMC_D4", /* BOOT_4 */
+		"eMMC_D5", /* BOOT_5 */
+		"eMMC_D6", /* BOOT_6 */
+		"eMMC_D7", /* BOOT_7 */
+		"eMMC_CLK", /* BOOT_8 */
+		"",
+		"eMMC_CMD", /* BOOT_10 */
+		"",
+		"eMMC_RST#", /* BOOT_12 */
+		"eMMC_DS", /* BOOT_13 */
+		"", "",
+		/* GPIOC */
+		"SD_D0_B", /* GPIOC_0 */
+		"SD_D1_B", /* GPIOC_1 */
+		"SD_D2_B", /* GPIOC_2 */
+		"SD_D3_B", /* GPIOC_3 */
+		"SD_CLK_B", /* GPIOC_4 */
+		"SD_CMD_B", /* GPIOC_5 */
+		"CARD_EN_DET", /* GPIOC_6 */
+		"",
+		/* GPIOA */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"CON1-P27", /* GPIOA_14 */
+		"CON1-P28", /* GPIOA_15 */
+		/* GPIOX */
+		"CON1-P16", /* GPIOX_0 */
+		"CON1-P18", /* GPIOX_1 */
+		"CON1-P22", /* GPIOX_2 */
+		"CON1-P11", /* GPIOX_3 */
+		"CON1-P13", /* GPIOX_4 */
+		"CON1-P07", /* GPIOX_5 */
+		"CON1-P33", /* GPIOX_6 */
+		"CON1-P15", /* GPIOX_7 */
+		"CON1-P19", /* GPIOX_8 */
+		"CON1-P21", /* GPIOX_9 */
+		"CON1-P24", /* GPIOX_10 */
+		"CON1-P23", /* GPIOX_11 */
+		"CON1-P08", /* GPIOX_12 */
+		"CON1-P10", /* GPIOX_13 */
+		"CON1-P29", /* GPIOX_14 */
+		"CON1-P31", /* GPIOX_15 */
+		"CON1-P26", /* GPIOX_16 */
+		"CON1-P03", /* GPIOX_17 */
+		"CON1-P05", /* GPIOX_18 */
+		"CON1-P32"; /* GPIOX_19 */
+
+	/*
+	 * WARNING: The USB Hub needs a reset signal to be turned high in
+	 * order to be detected by the USB Controller. This signal should
+	 * be handled by a USB specific power sequence to reset the Hub
+	 * when the USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&gpio_ao {
+	gpio-line-names =
+		/* GPIOAO */
+		"DEBUG TX", /* GPIOAO_0 */
+		"DEBUG RX", /* GPIOAO_1 */
+		"SYS_LED2", /* GPIOAO_2 */
+		"UPDATE_KEY", /* GPIOAO_3 */
+		"CON1-P40", /* GPIOAO_4 */
+		"IR_IN", /* GPIOAO_5 */
+		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
+		"CON1-P35", /* GPIOAO_7 */
+		"CON1-P12", /* GPIOAO_8 */
+		"CON1-P37", /* GPIOAO_9 */
+		"CON1-P38", /* GPIOAO_10 */
+		"SYS_LED", /* GPIOAO_11 */
+		/* GPIOE */
+		"VDDEE_PWM", /* GPIOE_0 */
+		"VDDCPU_PWM", /* GPIOE_1 */
+		"TF_PWR_EN"; /* GPIOE_2 */
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&dc_in>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	/* TOFIX: SD card is barely usable in SDR modes */
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&vddio_c>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&dc_in>;
+};
+
+&usb2_phy1 {
+	/* Enable the hub which is connected to this port */
+	phy-supply = <&vl_pwr_en>;
+};
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/4] arm64: dts: meson: meson-sm1-bananapi-m5: convert to dtsi

[Christian Hewitt]

Convert the BPI-M5 dts into meson-sm1-bananapi.dtsi to support the
addition of new boards based on the same design.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 .../dts/amlogic/meson-sm1-bananapi-m5.dts     | 427 +----------------
 .../boot/dts/amlogic/meson-sm1-bananapi.dtsi  | 435 ++++++++++++++++++
 2 files changed, 436 insertions(+), 426 deletions(-)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 3c1267a7ffef..34b3238ee0a0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -6,10 +6,7 @@
 
 /dts-v1/;
 
-#include "meson-sm1.dtsi"
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/input/linux-event-codes.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include "meson-sm1-bananapi.dtsi"
 #include <dt-bindings/sound/meson-g12a-toacodec.h>
 #include <dt-bindings/sound/meson-g12a-tohdmitx.h>
 
@@ -17,28 +14,6 @@ / {
 	compatible = "bananapi,bpi-m5", "amlogic,sm1";
 	model = "Banana Pi BPI-M5";
 
-	adc_keys {
-		compatible = "adc-keys";
-		io-channels = <&saradc 2>;
-		io-channel-names = "buttons";
-		keyup-threshold-microvolt = <1800000>;
-
-		key {
-			label = "SW3";
-			linux,code = <BTN_3>;
-			press-threshold-microvolt = <1700000>;
-		};
-	};
-
-	aliases {
-		serial0 = &uart_AO;
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
 	/* TOFIX: handle CVBS_DET on SARADC channel 0 */
 	cvbs-connector {
 		compatible = "composite-video-connector";
@@ -50,150 +25,6 @@ cvbs_connector_in: endpoint {
 		};
 	};
 
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		key {
-			label = "SW1";
-			linux,code = <BTN_1>;
-			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
-			interrupt-parent = <&gpio_intc>;
-			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
-		};
-	};
-
-	hdmi-connector {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_connector_in: endpoint {
-				remote-endpoint = <&hdmi_tx_tmds_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led-green {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
-		};
-
-		led-blue {
-			color = <LED_COLOR_ID_BLUE>;
-			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x40000000>;
-	};
-
-	emmc_1v8: regulator-emmc_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "EMMC_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	dc_in: regulator-dc_in {
-		compatible = "regulator-fixed";
-		regulator-name = "DC_IN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vddio_c: regulator-vddio_c {
-		compatible = "regulator-gpio";
-		regulator-name = "VDDIO_C";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-
-		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
-		gpios-states = <1>;
-
-		states = <1800000 0>,
-			 <3300000 1>;
-	};
-
-	tflash_vdd: regulator-tflash_vdd {
-		compatible = "regulator-fixed";
-		regulator-name = "TFLASH_VDD";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	vddao_1v8: regulator-vddao_1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_1V8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&dc_in>;
-		regulator-always-on;
-	};
-
-	vddcpu: regulator-vddcpu {
-		/*
-		 * SY8120B1ABC DC/DC Regulator.
-		 */
-		compatible = "pwm-regulator";
-
-		regulator-name = "VDDCPU";
-		regulator-min-microvolt = <690000>;
-		regulator-max-microvolt = <1050000>;
-
-		pwm-supply = <&dc_in>;
-
-		pwms = <&pwm_AO_cd 1 1250 0>;
-		pwm-dutycycle-range = <100 0>;
-
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	/* USB Hub Power Enable */
-	vl_pwr_en: regulator-vl_pwr_en {
-		compatible = "regulator-fixed";
-		regulator-name = "VL_PWR_EN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&dc_in>;
-
-		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "BPI-M5";
@@ -319,68 +150,17 @@ &acodec {
 	status = "okay";
 };
 
-&arb {
-	status = "okay";
-};
 
 &clkc_audio {
 	status = "okay";
 };
 
-&cpu0 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu1 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU1_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu2 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU2_CLK>;
-	clock-latency = <50000>;
-};
-
-&cpu3 {
-	cpu-supply = <&vddcpu>;
-	operating-points-v2 = <&cpu_opp_table>;
-	clocks = <&clkc CLKID_CPU3_CLK>;
-	clock-latency = <50000>;
-};
-
 &cvbs_vdac_port {
 	cvbs_vdac_out: endpoint {
 		remote-endpoint = <&cvbs_connector_in>;
 	};
 };
 
-&ext_mdio {
-	external_phy: ethernet-phy@0 {
-		/* Realtek RTL8211F (0x001cc916) */
-		reg = <0>;
-		max-speed = <1000>;
-
-		interrupt-parent = <&gpio_intc>;
-		/* MAC_INTR on GPIOZ_14 */
-		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&ethmac {
-	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-	phy-mode = "rgmii-txid";
-	phy-handle = <&external_phy>;
-};
-
 &frddr_a {
 	status = "okay";
 };
@@ -393,192 +173,6 @@ &frddr_c {
 	status = "okay";
 };
 
-&gpio {
-	gpio-line-names =
-		/* GPIOZ */
-		"ETH_MDIO", /* GPIOZ_0 */
-		"ETH_MDC", /* GPIOZ_1 */
-		"ETH_RXCLK", /* GPIOZ_2 */
-		"ETH_RX_DV", /* GPIOZ_3 */
-		"ETH_RXD0", /* GPIOZ_4 */
-		"ETH_RXD1", /* GPIOZ_5 */
-		"ETH_RXD2", /* GPIOZ_6 */
-		"ETH_RXD3", /* GPIOZ_7 */
-		"ETH_TXCLK", /* GPIOZ_8 */
-		"ETH_TXEN", /* GPIOZ_9 */
-		"ETH_TXD0", /* GPIOZ_10 */
-		"ETH_TXD1", /* GPIOZ_11 */
-		"ETH_TXD2", /* GPIOZ_12 */
-		"ETH_TXD3", /* GPIOZ_13 */
-		"ETH_INTR", /* GPIOZ_14 */
-		"ETH_NRST", /* GPIOZ_15 */
-		/* GPIOH */
-		"HDMI_SDA", /* GPIOH_0 */
-		"HDMI_SCL", /* GPIOH_1 */
-		"HDMI_HPD", /* GPIOH_2 */
-		"HDMI_CEC", /* GPIOH_3 */
-		"VL-RST_N", /* GPIOH_4 */
-		"CON1-P36", /* GPIOH_5 */
-		"VL-PWREN", /* GPIOH_6 */
-		"WiFi_3V3_1V8", /* GPIOH_7 */
-		"TFLASH_VDD_EN", /* GPIOH_8 */
-		/* BOOT */
-		"eMMC_D0", /* BOOT_0 */
-		"eMMC_D1", /* BOOT_1 */
-		"eMMC_D2", /* BOOT_2 */
-		"eMMC_D3", /* BOOT_3 */
-		"eMMC_D4", /* BOOT_4 */
-		"eMMC_D5", /* BOOT_5 */
-		"eMMC_D6", /* BOOT_6 */
-		"eMMC_D7", /* BOOT_7 */
-		"eMMC_CLK", /* BOOT_8 */
-		"",
-		"eMMC_CMD", /* BOOT_10 */
-		"",
-		"eMMC_RST#", /* BOOT_12 */
-		"eMMC_DS", /* BOOT_13 */
-		"", "",
-		/* GPIOC */
-		"SD_D0_B", /* GPIOC_0 */
-		"SD_D1_B", /* GPIOC_1 */
-		"SD_D2_B", /* GPIOC_2 */
-		"SD_D3_B", /* GPIOC_3 */
-		"SD_CLK_B", /* GPIOC_4 */
-		"SD_CMD_B", /* GPIOC_5 */
-		"CARD_EN_DET", /* GPIOC_6 */
-		"",
-		/* GPIOA */
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "",
-		"CON1-P27", /* GPIOA_14 */
-		"CON1-P28", /* GPIOA_15 */
-		/* GPIOX */
-		"CON1-P16", /* GPIOX_0 */
-		"CON1-P18", /* GPIOX_1 */
-		"CON1-P22", /* GPIOX_2 */
-		"CON1-P11", /* GPIOX_3 */
-		"CON1-P13", /* GPIOX_4 */
-		"CON1-P07", /* GPIOX_5 */
-		"CON1-P33", /* GPIOX_6 */
-		"CON1-P15", /* GPIOX_7 */
-		"CON1-P19", /* GPIOX_8 */
-		"CON1-P21", /* GPIOX_9 */
-		"CON1-P24", /* GPIOX_10 */
-		"CON1-P23", /* GPIOX_11 */
-		"CON1-P08", /* GPIOX_12 */
-		"CON1-P10", /* GPIOX_13 */
-		"CON1-P29", /* GPIOX_14 */
-		"CON1-P31", /* GPIOX_15 */
-		"CON1-P26", /* GPIOX_16 */
-		"CON1-P03", /* GPIOX_17 */
-		"CON1-P05", /* GPIOX_18 */
-		"CON1-P32"; /* GPIOX_19 */
-
-	/*
-	 * WARNING: The USB Hub on the BPI-M5 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&gpio_ao {
-	gpio-line-names =
-		/* GPIOAO */
-		"DEBUG TX", /* GPIOAO_0 */
-		"DEBUG RX", /* GPIOAO_1 */
-		"SYS_LED2", /* GPIOAO_2 */
-		"UPDATE_KEY", /* GPIOAO_3 */
-		"CON1-P40", /* GPIOAO_4 */
-		"IR_IN", /* GPIOAO_5 */
-		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
-		"CON1-P35", /* GPIOAO_7 */
-		"CON1-P12", /* GPIOAO_8 */
-		"CON1-P37", /* GPIOAO_9 */
-		"CON1-P38", /* GPIOAO_10 */
-		"SYS_LED", /* GPIOAO_11 */
-		/* GPIOE */
-		"VDDEE_PWM", /* GPIOE_0 */
-		"VDDCPU_PWM", /* GPIOE_1 */
-		"TF_PWR_EN"; /* GPIOE_2 */
-};
-
-&hdmi_tx {
-	status = "okay";
-	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
-	pinctrl-names = "default";
-	hdmi-supply = <&dc_in>;
-};
-
-&hdmi_tx_tmds_port {
-	hdmi_tx_tmds_out: endpoint {
-		remote-endpoint = <&hdmi_connector_in>;
-	};
-};
-
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-};
-
-&pwm_AO_cd {
-	pinctrl-0 = <&pwm_ao_d_e_pins>;
-	pinctrl-names = "default";
-	clocks = <&xtal>;
-	clock-names = "clkin1";
-	status = "okay";
-};
-
-&saradc {
-	status = "okay";
-	vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
-	status = "okay";
-	pinctrl-0 = <&sdcard_c_pins>;
-	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	max-frequency = <50000000>;
-	disable-wp;
-
-	/* TOFIX: SD card is barely usable in SDR modes */
-
-	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&tflash_vdd>;
-	vqmmc-supply = <&vddio_c>;
-};
-
-/* eMMC */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	max-frequency = <200000000>;
-	disable-wp;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&emmc_1v8>;
-};
-
 &tdmif_b {
 	status = "okay";
 };
@@ -626,22 +220,3 @@ &toddr_b {
 &toddr_c {
 	status = "okay";
 };
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-};
-
-&usb2_phy0 {
-	phy-supply = <&dc_in>;
-};
-
-&usb2_phy1 {
-	/* Enable the hub which is connected to this port */
-	phy-supply = <&vl_pwr_en>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
new file mode 100644
index 000000000000..c914f1148185
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi.dtsi
@@ -0,0 +1,435 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+
+/ {
+	adc_keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 2>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+
+		key {
+			label = "SW3";
+			linux,code = <BTN_3>;
+			press-threshold-microvolt = <1700000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key {
+			label = "SW1";
+			linux,code = <BTN_1>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+			interrupt-parent = <&gpio_intc>;
+			interrupts = <3 IRQ_TYPE_EDGE_BOTH>;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddio_c: regulator-vddio_c {
+		compatible = "regulator-gpio";
+		regulator-name = "VDDIO_C";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+
+		gpios = <&gpio_ao GPIOAO_6 GPIO_OPEN_DRAIN>;
+		gpios-states = <1>;
+
+		states = <1800000 0>,
+			 <3300000 1>;
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		/*
+		 * SY8120B1ABC DC/DC Regulator.
+		 */
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		pwm-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	/* USB Hub Power Enable */
+	vl_pwr_en: regulator-vl_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "VL_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+};
+
+&gpio {
+	gpio-line-names =
+		/* GPIOZ */
+		"ETH_MDIO", /* GPIOZ_0 */
+		"ETH_MDC", /* GPIOZ_1 */
+		"ETH_RXCLK", /* GPIOZ_2 */
+		"ETH_RX_DV", /* GPIOZ_3 */
+		"ETH_RXD0", /* GPIOZ_4 */
+		"ETH_RXD1", /* GPIOZ_5 */
+		"ETH_RXD2", /* GPIOZ_6 */
+		"ETH_RXD3", /* GPIOZ_7 */
+		"ETH_TXCLK", /* GPIOZ_8 */
+		"ETH_TXEN", /* GPIOZ_9 */
+		"ETH_TXD0", /* GPIOZ_10 */
+		"ETH_TXD1", /* GPIOZ_11 */
+		"ETH_TXD2", /* GPIOZ_12 */
+		"ETH_TXD3", /* GPIOZ_13 */
+		"ETH_INTR", /* GPIOZ_14 */
+		"ETH_NRST", /* GPIOZ_15 */
+		/* GPIOH */
+		"HDMI_SDA", /* GPIOH_0 */
+		"HDMI_SCL", /* GPIOH_1 */
+		"HDMI_HPD", /* GPIOH_2 */
+		"HDMI_CEC", /* GPIOH_3 */
+		"VL-RST_N", /* GPIOH_4 */
+		"CON1-P36", /* GPIOH_5 */
+		"VL-PWREN", /* GPIOH_6 */
+		"WiFi_3V3_1V8", /* GPIOH_7 */
+		"TFLASH_VDD_EN", /* GPIOH_8 */
+		/* BOOT */
+		"eMMC_D0", /* BOOT_0 */
+		"eMMC_D1", /* BOOT_1 */
+		"eMMC_D2", /* BOOT_2 */
+		"eMMC_D3", /* BOOT_3 */
+		"eMMC_D4", /* BOOT_4 */
+		"eMMC_D5", /* BOOT_5 */
+		"eMMC_D6", /* BOOT_6 */
+		"eMMC_D7", /* BOOT_7 */
+		"eMMC_CLK", /* BOOT_8 */
+		"",
+		"eMMC_CMD", /* BOOT_10 */
+		"",
+		"eMMC_RST#", /* BOOT_12 */
+		"eMMC_DS", /* BOOT_13 */
+		"", "",
+		/* GPIOC */
+		"SD_D0_B", /* GPIOC_0 */
+		"SD_D1_B", /* GPIOC_1 */
+		"SD_D2_B", /* GPIOC_2 */
+		"SD_D3_B", /* GPIOC_3 */
+		"SD_CLK_B", /* GPIOC_4 */
+		"SD_CMD_B", /* GPIOC_5 */
+		"CARD_EN_DET", /* GPIOC_6 */
+		"",
+		/* GPIOA */
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"CON1-P27", /* GPIOA_14 */
+		"CON1-P28", /* GPIOA_15 */
+		/* GPIOX */
+		"CON1-P16", /* GPIOX_0 */
+		"CON1-P18", /* GPIOX_1 */
+		"CON1-P22", /* GPIOX_2 */
+		"CON1-P11", /* GPIOX_3 */
+		"CON1-P13", /* GPIOX_4 */
+		"CON1-P07", /* GPIOX_5 */
+		"CON1-P33", /* GPIOX_6 */
+		"CON1-P15", /* GPIOX_7 */
+		"CON1-P19", /* GPIOX_8 */
+		"CON1-P21", /* GPIOX_9 */
+		"CON1-P24", /* GPIOX_10 */
+		"CON1-P23", /* GPIOX_11 */
+		"CON1-P08", /* GPIOX_12 */
+		"CON1-P10", /* GPIOX_13 */
+		"CON1-P29", /* GPIOX_14 */
+		"CON1-P31", /* GPIOX_15 */
+		"CON1-P26", /* GPIOX_16 */
+		"CON1-P03", /* GPIOX_17 */
+		"CON1-P05", /* GPIOX_18 */
+		"CON1-P32"; /* GPIOX_19 */
+
+	/*
+	 * WARNING: The USB Hub needs a reset signal to be turned high in
+	 * order to be detected by the USB Controller. This signal should
+	 * be handled by a USB specific power sequence to reset the Hub
+	 * when the USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&gpio_ao {
+	gpio-line-names =
+		/* GPIOAO */
+		"DEBUG TX", /* GPIOAO_0 */
+		"DEBUG RX", /* GPIOAO_1 */
+		"SYS_LED2", /* GPIOAO_2 */
+		"UPDATE_KEY", /* GPIOAO_3 */
+		"CON1-P40", /* GPIOAO_4 */
+		"IR_IN", /* GPIOAO_5 */
+		"TF_3V3N_1V8_EN", /* GPIOAO_6 */
+		"CON1-P35", /* GPIOAO_7 */
+		"CON1-P12", /* GPIOAO_8 */
+		"CON1-P37", /* GPIOAO_9 */
+		"CON1-P38", /* GPIOAO_10 */
+		"SYS_LED", /* GPIOAO_11 */
+		/* GPIOE */
+		"VDDEE_PWM", /* GPIOE_0 */
+		"VDDCPU_PWM", /* GPIOE_1 */
+		"TF_PWR_EN"; /* GPIOE_2 */
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&dc_in>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	/* TOFIX: SD card is barely usable in SDR modes */
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&vddio_c>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb2_phy0 {
+	phy-supply = <&dc_in>;
+};
+
+&usb2_phy1 {
+	/* Enable the hub which is connected to this port */
+	phy-supply = <&vl_pwr_en>;
+};
-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index e16b5fa55847..e935c92ab346 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -176,6 +176,7 @@ properties:
           - enum:
               - amediatech,x96-air
               - amediatech,x96-air-gbit
+              - bananapi,bpi-m2-pro
               - bananapi,bpi-m5
               - cyx,a95xf3-air
               - cyx,a95xf3-air-gbit
-- 
2.34.1

[PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index e16b5fa55847..e935c92ab346 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -176,6 +176,7 @@ properties:
           - enum:
               - amediatech,x96-air
               - amediatech,x96-air-gbit
+              - bananapi,bpi-m2-pro
               - bananapi,bpi-m5
               - cyx,a95xf3-air
               - cyx,a95xf3-air-gbit
-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index e16b5fa55847..e935c92ab346 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -176,6 +176,7 @@ properties:
           - enum:
               - amediatech,x96-air
               - amediatech,x96-air-gbit
+              - bananapi,bpi-m2-pro
               - bananapi,bpi-m5
               - cyx,a95xf3-air
               - cyx,a95xf3-air-gbit
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 design except for a different
physical board layout and the following changes:

- USB 3.0 ports reduced from 4x to 2x
- 3.5mm Combined CVBS/Audio Jack removed
- RTL8821BU WiFi/BT module (internal USB connected)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |  1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
 2 files changed, 99 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 97b42e2100e0..644451794aca 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
new file mode 100644
index 000000000000..4890d5d9a4f7
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-bananapi.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
+	model = "Banana Pi BPI-M2-PRO";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "BPI-M2-PRO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
-- 
2.34.1

[PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 design except for a different
physical board layout and the following changes:

- USB 3.0 ports reduced from 4x to 2x
- 3.5mm Combined CVBS/Audio Jack removed
- RTL8821BU WiFi/BT module (internal USB connected)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |  1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
 2 files changed, 99 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 97b42e2100e0..644451794aca 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
new file mode 100644
index 000000000000..4890d5d9a4f7
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-bananapi.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
+	model = "Banana Pi BPI-M2-PRO";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "BPI-M2-PRO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
-- 
2.34.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

[PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

BPI-M2-PRO is based upon the BPI-M5 design except for a different
physical board layout and the following changes:

- USB 3.0 ports reduced from 4x to 2x
- 3.5mm Combined CVBS/Audio Jack removed
- RTL8821BU WiFi/BT module (internal USB connected)

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |  1 +
 .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
 2 files changed, 99 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 97b42e2100e0..644451794aca 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
new file mode 100644
index 000000000000..4890d5d9a4f7
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 BayLibre SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-bananapi.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
+	model = "Banana Pi BPI-M2-PRO";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "BPI-M2-PRO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 3/4] dt-bindings: arm: amlogic: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 using the Amlogic SM1 (S905X3) chipset.
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 design except for a different
> physical board layout and the following changes:
> 
> - USB 3.0 ports reduced from 4x to 2x
> - 3.5mm Combined CVBS/Audio Jack removed
> - RTL8821BU WiFi/BT module (internal USB connected)
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>  .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>  2 files changed, 99 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 97b42e2100e0..644451794aca 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> new file mode 100644
> index 000000000000..4890d5d9a4f7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> @@ -0,0 +1,98 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 BayLibre SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-sm1-bananapi.dtsi"
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
> +	model = "Banana Pi BPI-M2-PRO";
> +
> +	sound {
> +		compatible = "amlogic,axg-sound-card";
> +		model = "BPI-M2-PRO";
> +		audio-aux-devs = <&tdmout_b>;
> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
> +				"TDM_B Playback", "TDMOUT_B OUT";
> +
> +		assigned-clocks = <&clkc CLKID_MPLL2>,
> +				  <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +		status = "okay";

It's by default. Did any DTSI disable the sound node?



Best regards,
Krzysztof

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 design except for a different
> physical board layout and the following changes:
> 
> - USB 3.0 ports reduced from 4x to 2x
> - 3.5mm Combined CVBS/Audio Jack removed
> - RTL8821BU WiFi/BT module (internal USB connected)
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>  .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>  2 files changed, 99 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 97b42e2100e0..644451794aca 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> new file mode 100644
> index 000000000000..4890d5d9a4f7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> @@ -0,0 +1,98 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 BayLibre SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-sm1-bananapi.dtsi"
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
> +	model = "Banana Pi BPI-M2-PRO";
> +
> +	sound {
> +		compatible = "amlogic,axg-sound-card";
> +		model = "BPI-M2-PRO";
> +		audio-aux-devs = <&tdmout_b>;
> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
> +				"TDM_B Playback", "TDMOUT_B OUT";
> +
> +		assigned-clocks = <&clkc CLKID_MPLL2>,
> +				  <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +		status = "okay";

It's by default. Did any DTSI disable the sound node?



Best regards,
Krzysztof


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:02, Christian Hewitt wrote:
> BPI-M2-PRO is based upon the BPI-M5 design except for a different
> physical board layout and the following changes:
> 
> - USB 3.0 ports reduced from 4x to 2x
> - 3.5mm Combined CVBS/Audio Jack removed
> - RTL8821BU WiFi/BT module (internal USB connected)
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>  .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>  2 files changed, 99 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 97b42e2100e0..644451794aca 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> new file mode 100644
> index 000000000000..4890d5d9a4f7
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
> @@ -0,0 +1,98 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 BayLibre SAS
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-sm1-bananapi.dtsi"
> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
> +
> +/ {
> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
> +	model = "Banana Pi BPI-M2-PRO";
> +
> +	sound {
> +		compatible = "amlogic,axg-sound-card";
> +		model = "BPI-M2-PRO";
> +		audio-aux-devs = <&tdmout_b>;
> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
> +				"TDM_B Playback", "TDMOUT_B OUT";
> +
> +		assigned-clocks = <&clkc CLKID_MPLL2>,
> +				  <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +		status = "okay";

It's by default. Did any DTSI disable the sound node?



Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Neil Armstrong]

On 27/01/2023 11:06, Krzysztof Kozlowski wrote:
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>>
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>>
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>>   arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>>   .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>>   2 files changed, 99 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

It's a leftover we keep copying onto new boards, I'll send a patch top remove all those.

Neil

> 
> 
> 
> Best regards,
> Krzysztof
> 

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Neil Armstrong]

On 27/01/2023 11:06, Krzysztof Kozlowski wrote:
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>>
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>>
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>>   arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>>   .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>>   2 files changed, 99 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

It's a leftover we keep copying onto new boards, I'll send a patch top remove all those.

Neil

> 
> 
> 
> Best regards,
> Krzysztof
> 


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Neil Armstrong]

On 27/01/2023 11:06, Krzysztof Kozlowski wrote:
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>>
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>>
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>>   arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>>   .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>>   2 files changed, 99 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>>
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>>   dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

It's a leftover we keep copying onto new boards, I'll send a patch top remove all those.

Neil

> 
> 
> 
> Best regards,
> Krzysztof
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 2:06 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>> 
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>> 
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>> arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>> .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>> 2 files changed, 99 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> 
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

No. I’m simply transcribing from the original M5 dts (with edits to omit
the audio jack bits) and the sound nodes of other Amlogic dts which have
long included the same. 

Q. Do I need to remove it here? (sounds like a yes)
Q. Do we need to exorcise/cleanup the same from all other meson dts?

Christian

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 2:06 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>> 
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>> 
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>> arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>> .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>> 2 files changed, 99 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> 
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

No. I’m simply transcribing from the original M5 dts (with edits to omit
the audio jack bits) and the sound nodes of other Amlogic dts which have
long included the same. 

Q. Do I need to remove it here? (sounds like a yes)
Q. Do we need to exorcise/cleanup the same from all other meson dts?

Christian


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 2:06 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:02, Christian Hewitt wrote:
>> BPI-M2-PRO is based upon the BPI-M5 design except for a different
>> physical board layout and the following changes:
>> 
>> - USB 3.0 ports reduced from 4x to 2x
>> - 3.5mm Combined CVBS/Audio Jack removed
>> - RTL8821BU WiFi/BT module (internal USB connected)
>> 
>> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
>> ---
>> arch/arm64/boot/dts/amlogic/Makefile          |  1 +
>> .../dts/amlogic/meson-sm1-bananapi-m2-pro.dts | 98 +++++++++++++++++++
>> 2 files changed, 99 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> 
>> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
>> index 97b42e2100e0..644451794aca 100644
>> --- a/arch/arm64/boot/dts/amlogic/Makefile
>> +++ b/arch/arm64/boot/dts/amlogic/Makefile
>> @@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
>> +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m2-pro.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
>> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
>> diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> new file mode 100644
>> index 000000000000..4890d5d9a4f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m2-pro.dts
>> @@ -0,0 +1,98 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Copyright (c) 2021 BayLibre SAS
>> + * Author: Neil Armstrong <narmstrong@baylibre.com>
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "meson-sm1-bananapi.dtsi"
>> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
>> +
>> +/ {
>> +	compatible = "bananapi,bpi-m2-pro", "amlogic,sm1";
>> +	model = "Banana Pi BPI-M2-PRO";
>> +
>> +	sound {
>> +		compatible = "amlogic,axg-sound-card";
>> +		model = "BPI-M2-PRO";
>> +		audio-aux-devs = <&tdmout_b>;
>> +		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
>> +				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
>> +				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
>> +				"TDM_B Playback", "TDMOUT_B OUT";
>> +
>> +		assigned-clocks = <&clkc CLKID_MPLL2>,
>> +				  <&clkc CLKID_MPLL0>,
>> +				  <&clkc CLKID_MPLL1>;
>> +		assigned-clock-parents = <0>, <0>, <0>;
>> +		assigned-clock-rates = <294912000>,
>> +				       <270950400>,
>> +				       <393216000>;
>> +		status = "okay";
> 
> It's by default. Did any DTSI disable the sound node?

No. I’m simply transcribing from the original M5 dts (with edits to omit
the audio jack bits) and the sound nodes of other Amlogic dts which have
long included the same. 

Q. Do I need to remove it here? (sounds like a yes)
Q. Do we need to exorcise/cleanup the same from all other meson dts?

Christian


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:19, Christian Hewitt wrote:
>> It's by default. Did any DTSI disable the sound node?
> 
> No. I’m simply transcribing from the original M5 dts (with edits to omit
> the audio jack bits) and the sound nodes of other Amlogic dts which have
> long included the same. 
> 
> Q. Do I need to remove it here? (sounds like a yes)

Yes

> Q. Do we need to exorcise/cleanup the same from all other meson dts?

Yes, please.

Best regards,
Krzysztof

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:19, Christian Hewitt wrote:
>> It's by default. Did any DTSI disable the sound node?
> 
> No. I’m simply transcribing from the original M5 dts (with edits to omit
> the audio jack bits) and the sound nodes of other Amlogic dts which have
> long included the same. 
> 
> Q. Do I need to remove it here? (sounds like a yes)

Yes

> Q. Do we need to exorcise/cleanup the same from all other meson dts?

Yes, please.

Best regards,
Krzysztof


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Krzysztof Kozlowski]

On 27/01/2023 11:19, Christian Hewitt wrote:
>> It's by default. Did any DTSI disable the sound node?
> 
> No. I’m simply transcribing from the original M5 dts (with edits to omit
> the audio jack bits) and the sound nodes of other Amlogic dts which have
> long included the same. 
> 
> Q. Do I need to remove it here? (sounds like a yes)

Yes

> Q. Do we need to exorcise/cleanup the same from all other meson dts?

Yes, please.

Best regards,
Krzysztof


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 5:01 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:19, Christian Hewitt wrote:
>>> It's by default. Did any DTSI disable the sound node?
>> 
>> No. I’m simply transcribing from the original M5 dts (with edits to omit
>> the audio jack bits) and the sound nodes of other Amlogic dts which have
>> long included the same. 
>> 
>> Q. Do I need to remove it here? (sounds like a yes)
> 
> Yes

I’ve removed for both dts and sent v2

>> Q. Do we need to exorcise/cleanup the same from all other meson dts?
> 
> Yes, please.

I’ll put on my to-do list :)

Christian

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 5:01 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:19, Christian Hewitt wrote:
>>> It's by default. Did any DTSI disable the sound node?
>> 
>> No. I’m simply transcribing from the original M5 dts (with edits to omit
>> the audio jack bits) and the sound nodes of other Amlogic dts which have
>> long included the same. 
>> 
>> Q. Do I need to remove it here? (sounds like a yes)
> 
> Yes

I’ve removed for both dts and sent v2

>> Q. Do we need to exorcise/cleanup the same from all other meson dts?
> 
> Yes, please.

I’ll put on my to-do list :)

Christian
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

Re: [PATCH 4/4] arm64: dts: meson: add support for BananaPi M2-Pro

[Christian Hewitt]

> On 27 Jan 2023, at 5:01 pm, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:
> 
> On 27/01/2023 11:19, Christian Hewitt wrote:
>>> It's by default. Did any DTSI disable the sound node?
>> 
>> No. I’m simply transcribing from the original M5 dts (with edits to omit
>> the audio jack bits) and the sound nodes of other Amlogic dts which have
>> long included the same. 
>> 
>> Q. Do I need to remove it here? (sounds like a yes)
> 
> Yes

I’ve removed for both dts and sent v2

>> Q. Do we need to exorcise/cleanup the same from all other meson dts?
> 
> Yes, please.

I’ll put on my to-do list :)

Christian
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel