[PATCH v1 00/10] Another round of tsens cleanups

[PATCH v1 00/10] Another round of tsens cleanups

[Amit Kucheria]

This is another series of tsens cleanups before we add interrupt support.
This applies on top of the earlier two series[1][2] that have already been
accepted for 4.19.

In this series, we have the following:
- splitup 8916 and 8974 register address spaces for SROT and TM
- cleanups: move to spdx, dead code removal, removal of id field
- Add support to map the SROT address space for DTs that list it separately
- Check if TSENS IP is enabled in firmware by querying the SROT space
- Add reg-names property to get more readable outputs in /proc/iomem
- Add myself as maintainer of tsens

Regards,
Amit

[1] https://lore.kernel.org/lkml/cover.1531895128.git.amit.kucheria@linaro.org/
[2] https://lore.kernel.org/lkml/cover.1532600791.git.amit.kucheria@linaro.org/


Amit Kucheria (10):
  arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two
  dt-bindings: thermal: Fix a typo in documentation
  thermal: tsens: Add SPDX license identifiers
  thermal: tsens: Get rid of dead code
  thermal: tsens: Rename map field in order to add a second address map
  thermal: tsens: Add the SROT address map
  thermal: tsens: Check if the IP is correctly enabled by firmware
  thermal: tsens: Get rid of 'id' field
  arm64: dts: qcom: Add reg-names for all tsens nodes
  MAINTAINERS: Add entry for Qualcomm TSENS thermal drivers

 .../devicetree/bindings/thermal/thermal.txt   |  2 +-
 MAINTAINERS                                   |  7 +++
 arch/arm/boot/dts/qcom-msm8974.dtsi           |  7 ++-
 arch/arm64/boot/dts/qcom/msm8916.dtsi         |  7 ++-
 arch/arm64/boot/dts/qcom/msm8996.dtsi         |  2 +
 arch/arm64/boot/dts/qcom/sdm845.dtsi          |  2 +
 drivers/thermal/qcom/tsens-8916.c             | 11 +---
 drivers/thermal/qcom/tsens-8960.c             | 41 +++++-------
 drivers/thermal/qcom/tsens-8974.c             | 11 +---
 drivers/thermal/qcom/tsens-common.c           | 62 ++++++++++++-------
 drivers/thermal/qcom/tsens-v2.c               |  6 +-
 drivers/thermal/qcom/tsens.c                  | 21 +------
 drivers/thermal/qcom/tsens.h                  | 24 +++----
 13 files changed, 99 insertions(+), 104 deletions(-)

-- 
2.17.1

[PATCH v1 00/10] Another round of tsens cleanups

[Amit Kucheria]

This is another series of tsens cleanups before we add interrupt support.
This applies on top of the earlier two series[1][2] that have already been
accepted for 4.19.

In this series, we have the following:
- splitup 8916 and 8974 register address spaces for SROT and TM
- cleanups: move to spdx, dead code removal, removal of id field
- Add support to map the SROT address space for DTs that list it separately
- Check if TSENS IP is enabled in firmware by querying the SROT space
- Add reg-names property to get more readable outputs in /proc/iomem
- Add myself as maintainer of tsens

Regards,
Amit

[1] https://lore.kernel.org/lkml/cover.1531895128.git.amit.kucheria at linaro.org/
[2] https://lore.kernel.org/lkml/cover.1532600791.git.amit.kucheria at linaro.org/


Amit Kucheria (10):
  arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two
  dt-bindings: thermal: Fix a typo in documentation
  thermal: tsens: Add SPDX license identifiers
  thermal: tsens: Get rid of dead code
  thermal: tsens: Rename map field in order to add a second address map
  thermal: tsens: Add the SROT address map
  thermal: tsens: Check if the IP is correctly enabled by firmware
  thermal: tsens: Get rid of 'id' field
  arm64: dts: qcom: Add reg-names for all tsens nodes
  MAINTAINERS: Add entry for Qualcomm TSENS thermal drivers

 .../devicetree/bindings/thermal/thermal.txt   |  2 +-
 MAINTAINERS                                   |  7 +++
 arch/arm/boot/dts/qcom-msm8974.dtsi           |  7 ++-
 arch/arm64/boot/dts/qcom/msm8916.dtsi         |  7 ++-
 arch/arm64/boot/dts/qcom/msm8996.dtsi         |  2 +
 arch/arm64/boot/dts/qcom/sdm845.dtsi          |  2 +
 drivers/thermal/qcom/tsens-8916.c             | 11 +---
 drivers/thermal/qcom/tsens-8960.c             | 41 +++++-------
 drivers/thermal/qcom/tsens-8974.c             | 11 +---
 drivers/thermal/qcom/tsens-common.c           | 62 ++++++++++++-------
 drivers/thermal/qcom/tsens-v2.c               |  6 +-
 drivers/thermal/qcom/tsens.c                  | 21 +------
 drivers/thermal/qcom/tsens.h                  | 24 +++----
 13 files changed, 99 insertions(+), 104 deletions(-)

-- 
2.17.1

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

We've earlier added support to split the register address space into TM
and SROT regions.

Split up the regmap address space into two for the remaining platforms that
have a similar register layout and make corresponding changes to the
get_temp_common() function used by these platforms.

Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT).  This is OK since the code
doesn't really use the SROT functionality yet.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
 drivers/thermal/qcom/tsens-common.c   | 5 +++--
 3 files changed, 11 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..3c4b81c29798 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -427,11 +427,13 @@
 			};
 		};
 
-		tsens: thermal-sensor@fc4a8000 {
+		tsens: thermal-sensor@fc4a9000 {
 			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a8000 0x2000>;
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
+			#qcom,sensors = <11>;
 			#thermal-sensor-cells = <1>;
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index cc1040eacdf5..abf84df5a7bc 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -774,11 +774,13 @@
 			};
 		};
 
-		tsens: thermal-sensor@4a8000 {
+		tsens: thermal-sensor@4a9000 {
 			compatible = "qcom,msm8916-tsens";
-			reg = <0x4a8000 0x2000>;
+			reg = <0x4a9000 0x1000>, /* TM */
+			      <0x4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
 			nvmem-cell-names = "calib", "calib_sel";
+			#qcom,sensors = <5>;
 			#thermal-sensor-cells = <1>;
 		};
 
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 6207d8d92351..478739543bbc 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -21,7 +21,7 @@
 #include <linux/regmap.h>
 #include "tsens.h"
 
-#define S0_ST_ADDR		0x1030
+#define STATUS_OFFSET		0x30
 #define SN_ADDR_OFFSET		0x4
 #define SN_ST_TEMP_MASK		0x3ff
 #define CAL_DEGC_PT1		30
@@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
 	unsigned int status_reg;
 	int last_temp = 0, ret;
 
-	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
+	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
 	ret = regmap_read(tmdev->map, status_reg, &code);
+
 	if (ret)
 		return ret;
 	last_temp = code & SN_ST_TEMP_MASK;
-- 
2.17.1

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

We've earlier added support to split the register address space into TM
and SROT regions.

Split up the regmap address space into two for the remaining platforms that
have a similar register layout and make corresponding changes to the
get_temp_common() function used by these platforms.

Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT).  This is OK since the code
doesn't really use the SROT functionality yet.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
 drivers/thermal/qcom/tsens-common.c   | 5 +++--
 3 files changed, 11 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d9019a49b292..3c4b81c29798 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -427,11 +427,13 @@
 			};
 		};
 
-		tsens: thermal-sensor at fc4a8000 {
+		tsens: thermal-sensor at fc4a9000 {
 			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a8000 0x2000>;
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
+			#qcom,sensors = <11>;
 			#thermal-sensor-cells = <1>;
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index cc1040eacdf5..abf84df5a7bc 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -774,11 +774,13 @@
 			};
 		};
 
-		tsens: thermal-sensor at 4a8000 {
+		tsens: thermal-sensor at 4a9000 {
 			compatible = "qcom,msm8916-tsens";
-			reg = <0x4a8000 0x2000>;
+			reg = <0x4a9000 0x1000>, /* TM */
+			      <0x4a8000 0x1000>; /* SROT */
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
 			nvmem-cell-names = "calib", "calib_sel";
+			#qcom,sensors = <5>;
 			#thermal-sensor-cells = <1>;
 		};
 
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 6207d8d92351..478739543bbc 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -21,7 +21,7 @@
 #include <linux/regmap.h>
 #include "tsens.h"
 
-#define S0_ST_ADDR		0x1030
+#define STATUS_OFFSET		0x30
 #define SN_ADDR_OFFSET		0x4
 #define SN_ST_TEMP_MASK		0x3ff
 #define CAL_DEGC_PT1		30
@@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
 	unsigned int status_reg;
 	int last_temp = 0, ret;
 
-	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
+	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
 	ret = regmap_read(tmdev->map, status_reg, &code);
+
 	if (ret)
 		return ret;
 	last_temp = code & SN_ST_TEMP_MASK;
-- 
2.17.1

[PATCH v1 02/10] dt-bindings: thermal: Fix a typo in documentation

[Amit Kucheria]

c(1) + x(1) was actually meant to be c(1) * x(1).

While we're at it, add some brackets to make it nicer to read.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 Documentation/devicetree/bindings/thermal/thermal.txt | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
index cc553f0952c5..751104213d08 100644
--- a/Documentation/devicetree/bindings/thermal/thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/thermal.txt
@@ -152,7 +152,7 @@ Optional property:
   Elem size: one cell	the sensors listed in the thermal-sensors property.
   Elem type: signed	Coefficients defaults to 1, in case this property
 			is not specified. A simple linear polynomial is used:
-			Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn.
+			Z = (c0 * x0) + (c1 * x1) + ... + (c(n-1) * x(n-1)) + cn.
 
 			The coefficients are ordered and they match with sensors
 			by means of sensor ID. Additional coefficients are
-- 
2.17.1

[PATCH v1 03/10] thermal: tsens: Add SPDX license identifiers

[Amit Kucheria]

The TSENS drivers use a GPL-2.0 license. Replace with equivalent SPDX
tags and delete the full license text.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-8916.c   | 11 +----------
 drivers/thermal/qcom/tsens-8960.c   | 11 +----------
 drivers/thermal/qcom/tsens-8974.c   | 11 +----------
 drivers/thermal/qcom/tsens-common.c | 11 +----------
 drivers/thermal/qcom/tsens.c        | 11 +----------
 drivers/thermal/qcom/tsens.h        | 11 ++---------
 6 files changed, 7 insertions(+), 59 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-8916.c b/drivers/thermal/qcom/tsens-8916.c
index fdf561b8b81d..c4955c85e922 100644
--- a/drivers/thermal/qcom/tsens-8916.c
+++ b/drivers/thermal/qcom/tsens-8916.c
@@ -1,15 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/platform_device.h>
diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
index 0451277d3a8f..4af76de7dc2e 100644
--- a/drivers/thermal/qcom/tsens-8960.c
+++ b/drivers/thermal/qcom/tsens-8960.c
@@ -1,15 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/platform_device.h>
diff --git a/drivers/thermal/qcom/tsens-8974.c b/drivers/thermal/qcom/tsens-8974.c
index 9baf77e8cbe3..7e149edbfeb6 100644
--- a/drivers/thermal/qcom/tsens-8974.c
+++ b/drivers/thermal/qcom/tsens-8974.c
@@ -1,15 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/platform_device.h>
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 478739543bbc..303e3fdaca98 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -1,15 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/err.h>
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index a2c9bfae3d86..90bb431cf740 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -1,15 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/err.h>
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 14331eb45a86..8207610f326a 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -1,15 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * This software is licensed under the terms of the GNU General Public
- * License version 2, as published by the Free Software Foundation, and
- * may be copied, distributed, and modified under those terms.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
+
 #ifndef __QCOM_TSENS_H__
 #define __QCOM_TSENS_H__
 
-- 
2.17.1

[PATCH v1 04/10] thermal: tsens: Get rid of dead code

[Amit Kucheria]

hw_id is dynamically allocated but not used anywhere. Get rid of dead
code.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index 90bb431cf740..9a8e8f7b4ae1 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -80,11 +80,6 @@ static int tsens_register(struct tsens_device *tmdev)
 {
 	int i;
 	struct thermal_zone_device *tzd;
-	u32 *hw_id, n = tmdev->num_sensors;
-
-	hw_id = devm_kcalloc(tmdev->dev, n, sizeof(u32), GFP_KERNEL);
-	if (!hw_id)
-		return -ENOMEM;
 
 	for (i = 0;  i < tmdev->num_sensors; i++) {
 		tmdev->sensor[i].tmdev = tmdev;
-- 
2.17.1

[PATCH v1 05/10] thermal: tsens: Rename map field in order to add a second address map

[Amit Kucheria]

The TSENS driver currently only uses a limited set of registers from the TM
address space. So it was ok to map just that set of registers and call it
"map".

We'd now like to map a second set: SROT registers to introduce new
functionality. Rename the "map" field to a more appropriate "tm_map".

The 8960 doesn't have a clear split between TM and SROT registers. To avoid
complicating the data structure, it will switchover to using tm_map for its
maps.

There is no functional change with this patch.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-8960.c   | 30 ++++++++++++++---------------
 drivers/thermal/qcom/tsens-common.c | 17 ++++++++--------
 drivers/thermal/qcom/tsens-v2.c     |  6 +++---
 drivers/thermal/qcom/tsens.h        |  2 +-
 4 files changed, 27 insertions(+), 28 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
index 4af76de7dc2e..0f0adb302a7b 100644
--- a/drivers/thermal/qcom/tsens-8960.c
+++ b/drivers/thermal/qcom/tsens-8960.c
@@ -60,7 +60,7 @@ static int suspend_8960(struct tsens_device *tmdev)
 {
 	int ret;
 	unsigned int mask;
-	struct regmap *map = tmdev->map;
+	struct regmap *map = tmdev->tm_map;
 
 	ret = regmap_read(map, THRESHOLD_ADDR, &tmdev->ctx.threshold);
 	if (ret)
@@ -85,7 +85,7 @@ static int suspend_8960(struct tsens_device *tmdev)
 static int resume_8960(struct tsens_device *tmdev)
 {
 	int ret;
-	struct regmap *map = tmdev->map;
+	struct regmap *map = tmdev->tm_map;
 
 	ret = regmap_update_bits(map, CNTL_ADDR, SW_RST, SW_RST);
 	if (ret)
@@ -117,12 +117,12 @@ static int enable_8960(struct tsens_device *tmdev, int id)
 	int ret;
 	u32 reg, mask;
 
-	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg);
+	ret = regmap_read(tmdev->tm_map, CNTL_ADDR, &reg);
 	if (ret)
 		return ret;
 
 	mask = BIT(id + SENSOR0_SHIFT);
-	ret = regmap_write(tmdev->map, CNTL_ADDR, reg | SW_RST);
+	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg | SW_RST);
 	if (ret)
 		return ret;
 
@@ -131,7 +131,7 @@ static int enable_8960(struct tsens_device *tmdev, int id)
 	else
 		reg |= mask | SLP_CLK_ENA_8660 | EN;
 
-	ret = regmap_write(tmdev->map, CNTL_ADDR, reg);
+	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg);
 	if (ret)
 		return ret;
 
@@ -148,7 +148,7 @@ static void disable_8960(struct tsens_device *tmdev)
 	mask <<= SENSOR0_SHIFT;
 	mask |= EN;
 
-	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg_cntl);
+	ret = regmap_read(tmdev->tm_map, CNTL_ADDR, &reg_cntl);
 	if (ret)
 		return;
 
@@ -159,7 +159,7 @@ static void disable_8960(struct tsens_device *tmdev)
 	else
 		reg_cntl &= ~SLP_CLK_ENA_8660;
 
-	regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
+	regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
 }
 
 static int init_8960(struct tsens_device *tmdev)
@@ -167,8 +167,8 @@ static int init_8960(struct tsens_device *tmdev)
 	int ret, i;
 	u32 reg_cntl;
 
-	tmdev->map = dev_get_regmap(tmdev->dev, NULL);
-	if (!tmdev->map)
+	tmdev->tm_map = dev_get_regmap(tmdev->dev, NULL);
+	if (!tmdev->tm_map)
 		return -ENODEV;
 
 	/*
@@ -184,14 +184,14 @@ static int init_8960(struct tsens_device *tmdev)
 	}
 
 	reg_cntl = SW_RST;
-	ret = regmap_update_bits(tmdev->map, CNTL_ADDR, SW_RST, reg_cntl);
+	ret = regmap_update_bits(tmdev->tm_map, CNTL_ADDR, SW_RST, reg_cntl);
 	if (ret)
 		return ret;
 
 	if (tmdev->num_sensors > 1) {
 		reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18);
 		reg_cntl &= ~SW_RST;
-		ret = regmap_update_bits(tmdev->map, CONFIG_ADDR,
+		ret = regmap_update_bits(tmdev->tm_map, CONFIG_ADDR,
 					 CONFIG_MASK, CONFIG);
 	} else {
 		reg_cntl |= SLP_CLK_ENA_8660 | (MEASURE_PERIOD << 16);
@@ -200,12 +200,12 @@ static int init_8960(struct tsens_device *tmdev)
 	}
 
 	reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << SENSOR0_SHIFT;
-	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
+	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
 	if (ret)
 		return ret;
 
 	reg_cntl |= EN;
-	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
+	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
 	if (ret)
 		return ret;
 
@@ -252,12 +252,12 @@ static int get_temp_8960(struct tsens_device *tmdev, int id, int *temp)
 
 	timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
 	do {
-		ret = regmap_read(tmdev->map, INT_STATUS_ADDR, &trdy);
+		ret = regmap_read(tmdev->tm_map, INT_STATUS_ADDR, &trdy);
 		if (ret)
 			return ret;
 		if (!(trdy & TRDY_MASK))
 			continue;
-		ret = regmap_read(tmdev->map, s->status, &code);
+		ret = regmap_read(tmdev->tm_map, s->status, &code);
 		if (ret)
 			return ret;
 		*temp = code_to_mdegC(code, s);
diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 303e3fdaca98..0585084630b3 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -99,8 +99,7 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
 	int last_temp = 0, ret;
 
 	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
-	ret = regmap_read(tmdev->map, status_reg, &code);
-
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
 	if (ret)
 		return ret;
 	last_temp = code & SN_ST_TEMP_MASK;
@@ -118,7 +117,7 @@ static const struct regmap_config tsens_config = {
 
 int __init init_common(struct tsens_device *tmdev)
 {
-	void __iomem *base;
+	void __iomem *tm_base;
 	struct resource *res;
 	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
 
@@ -134,13 +133,13 @@ int __init init_common(struct tsens_device *tmdev)
 	}
 
 	res = platform_get_resource(op, IORESOURCE_MEM, 0);
-	base = devm_ioremap_resource(&op->dev, res);
-	if (IS_ERR(base))
-		return PTR_ERR(base);
+	tm_base = devm_ioremap_resource(&op->dev, res);
+	if (IS_ERR(tm_base))
+		return PTR_ERR(tm_base);
 
-	tmdev->map = devm_regmap_init_mmio(tmdev->dev, base, &tsens_config);
-	if (IS_ERR(tmdev->map))
-		return PTR_ERR(tmdev->map);
+	tmdev->tm_map = devm_regmap_init_mmio(tmdev->dev, tm_base, &tsens_config);
+	if (IS_ERR(tmdev->tm_map))
+		return PTR_ERR(tmdev->tm_map);
 
 	return 0;
 }
diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
index 44da02f594ac..1bdef92e4521 100644
--- a/drivers/thermal/qcom/tsens-v2.c
+++ b/drivers/thermal/qcom/tsens-v2.c
@@ -21,7 +21,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
 	int ret;
 
 	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * 4;
-	ret = regmap_read(tmdev->map, status_reg, &code);
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
 	if (ret)
 		return ret;
 	last_temp = code & LAST_TEMP_MASK;
@@ -29,7 +29,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
 		goto done;
 
 	/* Try a second time */
-	ret = regmap_read(tmdev->map, status_reg, &code);
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
 	if (ret)
 		return ret;
 	if (code & STATUS_VALID_BIT) {
@@ -40,7 +40,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
 	}
 
 	/* Try a third/last time */
-	ret = regmap_read(tmdev->map, status_reg, &code);
+	ret = regmap_read(tmdev->tm_map, status_reg, &code);
 	if (ret)
 		return ret;
 	if (code & STATUS_VALID_BIT) {
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 8207610f326a..58e98c4d3a8b 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -69,7 +69,7 @@ struct tsens_context {
 struct tsens_device {
 	struct device			*dev;
 	u32				num_sensors;
-	struct regmap			*map;
+	struct regmap			*tm_map;
 	u32				tm_offset;
 	struct tsens_context		ctx;
 	const struct tsens_ops		*ops;
-- 
2.17.1

[PATCH v1 06/10] thermal: tsens: Add the SROT address map

[Amit Kucheria]

On platforms whose device trees specify two address spaces for TSENS, the
second one points to the SROT registers. Initialise the SROT map on those
platforms.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 14 ++++++++++++--
 drivers/thermal/qcom/tsens.h        |  1 +
 2 files changed, 13 insertions(+), 2 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 0585084630b3..0b8a793f15f4 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -117,16 +117,26 @@ static const struct regmap_config tsens_config = {
 
 int __init init_common(struct tsens_device *tmdev)
 {
-	void __iomem *tm_base;
+	void __iomem *tm_base, *srot_base;
 	struct resource *res;
 	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
 
 	if (!op)
 		return -EINVAL;
 
-	/* The driver only uses the TM register address space for now */
 	if (op->num_resources > 1) {
+		/* DT with separate SROT and TM address space */
 		tmdev->tm_offset = 0;
+		res = platform_get_resource(op, IORESOURCE_MEM, 1);
+		srot_base = devm_ioremap_resource(&op->dev, res);
+		if (IS_ERR(srot_base))
+			return PTR_ERR(srot_base);
+
+		tmdev->srot_map = devm_regmap_init_mmio(tmdev->dev,
+							srot_base, &tsens_config);
+		if (IS_ERR(tmdev->srot_map))
+			return PTR_ERR(tmdev->srot_map);
+
 	} else {
 		/* old DTs where SROT and TM were in a contiguous 2K block */
 		tmdev->tm_offset = 0x1000;
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 58e98c4d3a8b..b9c4bcf255fa 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -70,6 +70,7 @@ struct tsens_device {
 	struct device			*dev;
 	u32				num_sensors;
 	struct regmap			*tm_map;
+	struct regmap			*srot_map;
 	u32				tm_offset;
 	struct tsens_context		ctx;
 	const struct tsens_ops		*ops;
-- 
2.17.1

[PATCH v1 07/10] thermal: tsens: Check if the IP is correctly enabled by firmware

[Amit Kucheria]

The SROT registers are initialised by the secure firmware at boot. We
don't have write access to the registers. Check if the block is enabled
before continuing.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens-common.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
index 0b8a793f15f4..d250b757d1f0 100644
--- a/drivers/thermal/qcom/tsens-common.c
+++ b/drivers/thermal/qcom/tsens-common.c
@@ -12,6 +12,11 @@
 #include <linux/regmap.h>
 #include "tsens.h"
 
+/* SROT */
+#define CTRL_OFFSET		0x4
+#define TSENS_EN		BIT(0)
+
+/* TM */
 #define STATUS_OFFSET		0x30
 #define SN_ADDR_OFFSET		0x4
 #define SN_ST_TEMP_MASK		0x3ff
@@ -119,6 +124,8 @@ int __init init_common(struct tsens_device *tmdev)
 {
 	void __iomem *tm_base, *srot_base;
 	struct resource *res;
+	u32 code;
+	int ret;
 	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
 
 	if (!op)
@@ -151,5 +158,15 @@ int __init init_common(struct tsens_device *tmdev)
 	if (IS_ERR(tmdev->tm_map))
 		return PTR_ERR(tmdev->tm_map);
 
+	if (tmdev->srot_map) {
+		ret = regmap_read(tmdev->srot_map, CTRL_OFFSET, &code);
+		if (ret)
+			return ret;
+		if (!(code & TSENS_EN)) {
+			dev_err(tmdev->dev, "tsens device is not enabled\n");
+			return -ENODEV;
+		}
+	}
+
 	return 0;
 }
-- 
2.17.1

[PATCH v1 08/10] thermal: tsens: Get rid of 'id' field

[Amit Kucheria]

The hw_id field in 'struct tsens_sensor' can do the job of tracking
unique ids for each sensor connected to each tsens device instance. It
also allows hw_ids to be overridden (e.g. 8916) in cases where some
sensors in a sequence are disabled on a particular platform.

Use the hw_id field instead of the id field consistently across the
tsens code.

While, we're at it, document the fields of struct tsens_sensor.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 drivers/thermal/qcom/tsens.c |  5 ++---
 drivers/thermal/qcom/tsens.h | 10 +++++++++-
 2 files changed, 11 insertions(+), 4 deletions(-)

diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index 9a8e8f7b4ae1..fb728ec5d77f 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -17,7 +17,7 @@ static int tsens_get_temp(void *data, int *temp)
 	const struct tsens_sensor *s = data;
 	struct tsens_device *tmdev = s->tmdev;
 
-	return tmdev->ops->get_temp(tmdev, s->id, temp);
+	return tmdev->ops->get_temp(tmdev, s->hw_id, temp);
 }
 
 static int tsens_get_trend(void *p, int trip, enum thermal_trend *trend)
@@ -26,7 +26,7 @@ static int tsens_get_trend(void *p, int trip, enum thermal_trend *trend)
 	struct tsens_device *tmdev = s->tmdev;
 
 	if (tmdev->ops->get_trend)
-		return  tmdev->ops->get_trend(tmdev, s->id, trend);
+		return  tmdev->ops->get_trend(tmdev, s->hw_id, trend);
 
 	return -ENOTSUPP;
 }
@@ -83,7 +83,6 @@ static int tsens_register(struct tsens_device *tmdev)
 
 	for (i = 0;  i < tmdev->num_sensors; i++) {
 		tmdev->sensor[i].tmdev = tmdev;
-		tmdev->sensor[i].id = i;
 		tzd = devm_thermal_zone_of_sensor_register(tmdev->dev, i,
 							   &tmdev->sensor[i],
 							   &tsens_of_ops);
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index b9c4bcf255fa..2a3174dfc1a9 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -14,11 +14,19 @@
 
 struct tsens_device;
 
+/**
+ * struct tsens_sensor - sensor-specific data
+ * @tmdev: tsens device instance this sensor is connected to
+ * @tzd: thermal zone corresponding to this sensor
+ * @offset: offset from calibration data to convert ADC data to degrees
+ * @hw_id: unique sensor ID for each sensor connected to tsens device instance
+ * @slope: slope from calibration data to convert ADC data to degrees
+ * @status: 8960-specific status register addresses
+ */
 struct tsens_sensor {
 	struct tsens_device		*tmdev;
 	struct thermal_zone_device	*tzd;
 	int				offset;
-	int				id;
 	int				hw_id;
 	int				slope;
 	u32				status;
-- 
2.17.1

[PATCH v1 09/10] arm64: dts: qcom: Add reg-names for all tsens nodes

[Amit Kucheria]

Instead of showing up as thermal-sensor@<addr>, the nodes will show up as
tsens0_tm, tsen1_tm, tsens1_srot, etc. in /proc/iomem making it easier to
read.

IOW,

0c222000-0c2221fe : thermal-sensor@c263000
0c223000-0c2231fe : thermal-sensor@c265000
0c263000-0c2631fe : thermal-sensor@c263000
0c265000-0c2651fe : thermal-sensor@c265000

becomes

0c222000-0c2221fe : tsens0_srot
0c223000-0c2231fe : tsens1_srot
0c263000-0c2631fe : tsens0_tm
0c265000-0c2651fe : tsens1_tm

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm/boot/dts/qcom-msm8974.dtsi   | 1 +
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 ++
 arch/arm64/boot/dts/qcom/sdm845.dtsi  | 2 ++
 4 files changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 3c4b81c29798..64c9f81ddd90 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -431,6 +431,7 @@
 			compatible = "qcom,msm8974-tsens";
 			reg = <0xfc4a9000 0x1000>, /* TM */
 			      <0xfc4a8000 0x1000>; /* SROT */
+			reg-names = "tsens_tm", "tsens_srot";
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
 			#qcom,sensors = <11>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index abf84df5a7bc..4e6a5e462a91 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -778,6 +778,7 @@
 			compatible = "qcom,msm8916-tsens";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
+			reg-names = "tsens_tm", "tsens_srot";
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
 			nvmem-cell-names = "calib", "calib_sel";
 			#qcom,sensors = <5>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index c2dca3a30091..7e5982daa2ed 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -969,6 +969,7 @@
 			compatible = "qcom,msm8996-tsens";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
+			reg-names = "tsens0_tm", "tsens0_srot";
 			#qcom,sensors = <13>;
 			#thermal-sensor-cells = <1>;
 		};
@@ -977,6 +978,7 @@
 			compatible = "qcom,msm8996-tsens";
 			reg = <0x4ad000 0x1000>, /* TM */
 			      <0x4ac000 0x1000>; /* SROT */
+			reg-names = "tsens1_tm", "tsens1_srot";
 			#qcom,sensors = <8>;
 			#thermal-sensor-cells = <1>;
 		};
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index f722785df26b..efd5d7abd1cd 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -1531,6 +1531,7 @@
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
 			reg = <0xc263000 0x1ff>, /* TM */
 			      <0xc222000 0x1ff>; /* SROT */
+			reg-names = "tsens0_tm", "tsens0_srot";
 			#qcom,sensors = <13>;
 			#thermal-sensor-cells = <1>;
 		};
@@ -1539,6 +1540,7 @@
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
 			reg = <0xc265000 0x1ff>, /* TM */
 			      <0xc223000 0x1ff>; /* SROT */
+			reg-names = "tsens1_tm", "tsens1_srot";
 			#qcom,sensors = <8>;
 			#thermal-sensor-cells = <1>;
 		};
-- 
2.17.1

[PATCH v1 09/10] arm64: dts: qcom: Add reg-names for all tsens nodes

[Amit Kucheria]

Instead of showing up as thermal-sensor@<addr>, the nodes will show up as
tsens0_tm, tsen1_tm, tsens1_srot, etc. in /proc/iomem making it easier to
read.

IOW,

0c222000-0c2221fe : thermal-sensor at c263000
0c223000-0c2231fe : thermal-sensor at c265000
0c263000-0c2631fe : thermal-sensor at c263000
0c265000-0c2651fe : thermal-sensor at c265000

becomes

0c222000-0c2221fe : tsens0_srot
0c223000-0c2231fe : tsens1_srot
0c263000-0c2631fe : tsens0_tm
0c265000-0c2651fe : tsens1_tm

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 arch/arm/boot/dts/qcom-msm8974.dtsi   | 1 +
 arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
 arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 ++
 arch/arm64/boot/dts/qcom/sdm845.dtsi  | 2 ++
 4 files changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 3c4b81c29798..64c9f81ddd90 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -431,6 +431,7 @@
 			compatible = "qcom,msm8974-tsens";
 			reg = <0xfc4a9000 0x1000>, /* TM */
 			      <0xfc4a8000 0x1000>; /* SROT */
+			reg-names = "tsens_tm", "tsens_srot";
 			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 			nvmem-cell-names = "calib", "calib_backup";
 			#qcom,sensors = <11>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index abf84df5a7bc..4e6a5e462a91 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -778,6 +778,7 @@
 			compatible = "qcom,msm8916-tsens";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
+			reg-names = "tsens_tm", "tsens_srot";
 			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
 			nvmem-cell-names = "calib", "calib_sel";
 			#qcom,sensors = <5>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index c2dca3a30091..7e5982daa2ed 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -969,6 +969,7 @@
 			compatible = "qcom,msm8996-tsens";
 			reg = <0x4a9000 0x1000>, /* TM */
 			      <0x4a8000 0x1000>; /* SROT */
+			reg-names = "tsens0_tm", "tsens0_srot";
 			#qcom,sensors = <13>;
 			#thermal-sensor-cells = <1>;
 		};
@@ -977,6 +978,7 @@
 			compatible = "qcom,msm8996-tsens";
 			reg = <0x4ad000 0x1000>, /* TM */
 			      <0x4ac000 0x1000>; /* SROT */
+			reg-names = "tsens1_tm", "tsens1_srot";
 			#qcom,sensors = <8>;
 			#thermal-sensor-cells = <1>;
 		};
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index f722785df26b..efd5d7abd1cd 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -1531,6 +1531,7 @@
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
 			reg = <0xc263000 0x1ff>, /* TM */
 			      <0xc222000 0x1ff>; /* SROT */
+			reg-names = "tsens0_tm", "tsens0_srot";
 			#qcom,sensors = <13>;
 			#thermal-sensor-cells = <1>;
 		};
@@ -1539,6 +1540,7 @@
 			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
 			reg = <0xc265000 0x1ff>, /* TM */
 			      <0xc223000 0x1ff>; /* SROT */
+			reg-names = "tsens1_tm", "tsens1_srot";
 			#qcom,sensors = <8>;
 			#thermal-sensor-cells = <1>;
 		};
-- 
2.17.1

[PATCH v1 10/10] MAINTAINERS: Add entry for Qualcomm TSENS thermal drivers

[Amit Kucheria]

Create an entry for the TSENS drivers and mark them as maintained

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 68b4ff8ed205..ca6183d6d545 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11862,6 +11862,13 @@ L:	linux-arm-msm@vger.kernel.org
 S:	Maintained
 F:	drivers/iommu/qcom_iommu.c
 
+QUALCOMM TSENS THERMAL DRIVER
+M:	Amit Kucheria <amit.kucheria@linaro.org>
+L:	linux-pm@vger.kernel.org
+L:	linux-arm-msm@vger.kernel.org
+S:	Maintained
+F:	drivers/thermal/qcom/
+
 QUALCOMM VENUS VIDEO ACCELERATOR DRIVER
 M:	Stanimir Varbanov <stanimir.varbanov@linaro.org>
 L:	linux-media@vger.kernel.org
-- 
2.17.1

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
>  drivers/thermal/qcom/tsens-common.c   | 5 +++--
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@fc4a8000 {
> +		tsens: thermal-sensor@fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;

nit: adding the number of sensors isn't directly related and probably
should be in a separate patch. Not important enough to re-spin just
for this though ;-)

>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@4a8000 {
> +		tsens: thermal-sensor@4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;

ditto

>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
>  drivers/thermal/qcom/tsens-common.c   | 5 +++--
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at fc4a8000 {
> +		tsens: thermal-sensor at fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;

nit: adding the number of sensors isn't directly related and probably
should be in a separate patch. Not important enough to re-spin just
for this though ;-)

>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at 4a8000 {
> +		tsens: thermal-sensor at 4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;

ditto

>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 02/10] dt-bindings: thermal: Fix a typo in documentation

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:34PM +0530, Amit Kucheria wrote:
> c(1) + x(1) was actually meant to be c(1) * x(1).
> 
> While we're at it, add some brackets to make it nicer to read.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  Documentation/devicetree/bindings/thermal/thermal.txt | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
> index cc553f0952c5..751104213d08 100644
> --- a/Documentation/devicetree/bindings/thermal/thermal.txt
> +++ b/Documentation/devicetree/bindings/thermal/thermal.txt
> @@ -152,7 +152,7 @@ Optional property:
>    Elem size: one cell	the sensors listed in the thermal-sensors property.
>    Elem type: signed	Coefficients defaults to 1, in case this property
>  			is not specified. A simple linear polynomial is used:
> -			Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn.
> +			Z = (c0 * x0) + (c1 * x1) + ... + (c(n-1) * x(n-1)) + cn.
>  
>  			The coefficients are ordered and they match with sensors
>  			by means of sensor ID. Additional coefficients are

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 03/10] thermal: tsens: Add SPDX license identifiers

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:35PM +0530, Amit Kucheria wrote:
> The TSENS drivers use a GPL-2.0 license. Replace with equivalent SPDX
> tags and delete the full license text.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens-8916.c   | 11 +----------
>  drivers/thermal/qcom/tsens-8960.c   | 11 +----------
>  drivers/thermal/qcom/tsens-8974.c   | 11 +----------
>  drivers/thermal/qcom/tsens-common.c | 11 +----------
>  drivers/thermal/qcom/tsens.c        | 11 +----------
>  drivers/thermal/qcom/tsens.h        | 11 ++---------
>  6 files changed, 7 insertions(+), 59 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens-8916.c b/drivers/thermal/qcom/tsens-8916.c
> index fdf561b8b81d..c4955c85e922 100644
> --- a/drivers/thermal/qcom/tsens-8916.c
> +++ b/drivers/thermal/qcom/tsens-8916.c
> @@ -1,15 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 and
> - * only version 2 as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
>   */
>  
>  #include <linux/platform_device.h>
> diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
> index 0451277d3a8f..4af76de7dc2e 100644
> --- a/drivers/thermal/qcom/tsens-8960.c
> +++ b/drivers/thermal/qcom/tsens-8960.c
> @@ -1,15 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 and
> - * only version 2 as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
>   */
>  
>  #include <linux/platform_device.h>
> diff --git a/drivers/thermal/qcom/tsens-8974.c b/drivers/thermal/qcom/tsens-8974.c
> index 9baf77e8cbe3..7e149edbfeb6 100644
> --- a/drivers/thermal/qcom/tsens-8974.c
> +++ b/drivers/thermal/qcom/tsens-8974.c
> @@ -1,15 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 and
> - * only version 2 as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
>   */
>  
>  #include <linux/platform_device.h>
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 478739543bbc..303e3fdaca98 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -1,15 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 and
> - * only version 2 as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
>   */
>  
>  #include <linux/err.h>
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index a2c9bfae3d86..90bb431cf740 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -1,15 +1,6 @@
> +// SPDX-License-Identifier: GPL-2.0
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License version 2 and
> - * only version 2 as published by the Free Software Foundation.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
>   */
>  
>  #include <linux/err.h>
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index 14331eb45a86..8207610f326a 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -1,15 +1,8 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
>  /*
>   * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> - *
> - * This software is licensed under the terms of the GNU General Public
> - * License version 2, as published by the Free Software Foundation, and
> - * may be copied, distributed, and modified under those terms.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
>   */
> +
>  #ifndef __QCOM_TSENS_H__
>  #define __QCOM_TSENS_H__
>  

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 04/10] thermal: tsens: Get rid of dead code

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:36PM +0530, Amit Kucheria wrote:
> hw_id is dynamically allocated but not used anywhere. Get rid of dead
> code.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens.c | 5 -----
>  1 file changed, 5 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index 90bb431cf740..9a8e8f7b4ae1 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -80,11 +80,6 @@ static int tsens_register(struct tsens_device *tmdev)
>  {
>  	int i;
>  	struct thermal_zone_device *tzd;
> -	u32 *hw_id, n = tmdev->num_sensors;
> -
> -	hw_id = devm_kcalloc(tmdev->dev, n, sizeof(u32), GFP_KERNEL);
> -	if (!hw_id)
> -		return -ENOMEM;
>  
>  	for (i = 0;  i < tmdev->num_sensors; i++) {
>  		tmdev->sensor[i].tmdev = tmdev;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 05/10] thermal: tsens: Rename map field in order to add a second address map

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:37PM +0530, Amit Kucheria wrote:
> The TSENS driver currently only uses a limited set of registers from the TM
> address space. So it was ok to map just that set of registers and call it
> "map".
> 
> We'd now like to map a second set: SROT registers to introduce new
> functionality. Rename the "map" field to a more appropriate "tm_map".
> 
> The 8960 doesn't have a clear split between TM and SROT registers. To avoid
> complicating the data structure, it will switchover to using tm_map for its
> maps.
> 
> There is no functional change with this patch.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens-8960.c   | 30 ++++++++++++++---------------
>  drivers/thermal/qcom/tsens-common.c | 17 ++++++++--------
>  drivers/thermal/qcom/tsens-v2.c     |  6 +++---
>  drivers/thermal/qcom/tsens.h        |  2 +-
>  4 files changed, 27 insertions(+), 28 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
> index 4af76de7dc2e..0f0adb302a7b 100644
> --- a/drivers/thermal/qcom/tsens-8960.c
> +++ b/drivers/thermal/qcom/tsens-8960.c
> @@ -60,7 +60,7 @@ static int suspend_8960(struct tsens_device *tmdev)
>  {
>  	int ret;
>  	unsigned int mask;
> -	struct regmap *map = tmdev->map;
> +	struct regmap *map = tmdev->tm_map;
>  
>  	ret = regmap_read(map, THRESHOLD_ADDR, &tmdev->ctx.threshold);
>  	if (ret)
> @@ -85,7 +85,7 @@ static int suspend_8960(struct tsens_device *tmdev)
>  static int resume_8960(struct tsens_device *tmdev)
>  {
>  	int ret;
> -	struct regmap *map = tmdev->map;
> +	struct regmap *map = tmdev->tm_map;
>  
>  	ret = regmap_update_bits(map, CNTL_ADDR, SW_RST, SW_RST);
>  	if (ret)
> @@ -117,12 +117,12 @@ static int enable_8960(struct tsens_device *tmdev, int id)
>  	int ret;
>  	u32 reg, mask;
>  
> -	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg);
> +	ret = regmap_read(tmdev->tm_map, CNTL_ADDR, &reg);
>  	if (ret)
>  		return ret;
>  
>  	mask = BIT(id + SENSOR0_SHIFT);
> -	ret = regmap_write(tmdev->map, CNTL_ADDR, reg | SW_RST);
> +	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg | SW_RST);
>  	if (ret)
>  		return ret;
>  
> @@ -131,7 +131,7 @@ static int enable_8960(struct tsens_device *tmdev, int id)
>  	else
>  		reg |= mask | SLP_CLK_ENA_8660 | EN;
>  
> -	ret = regmap_write(tmdev->map, CNTL_ADDR, reg);
> +	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg);
>  	if (ret)
>  		return ret;
>  
> @@ -148,7 +148,7 @@ static void disable_8960(struct tsens_device *tmdev)
>  	mask <<= SENSOR0_SHIFT;
>  	mask |= EN;
>  
> -	ret = regmap_read(tmdev->map, CNTL_ADDR, &reg_cntl);
> +	ret = regmap_read(tmdev->tm_map, CNTL_ADDR, &reg_cntl);
>  	if (ret)
>  		return;
>  
> @@ -159,7 +159,7 @@ static void disable_8960(struct tsens_device *tmdev)
>  	else
>  		reg_cntl &= ~SLP_CLK_ENA_8660;
>  
> -	regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +	regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
>  }
>  
>  static int init_8960(struct tsens_device *tmdev)
> @@ -167,8 +167,8 @@ static int init_8960(struct tsens_device *tmdev)
>  	int ret, i;
>  	u32 reg_cntl;
>  
> -	tmdev->map = dev_get_regmap(tmdev->dev, NULL);
> -	if (!tmdev->map)
> +	tmdev->tm_map = dev_get_regmap(tmdev->dev, NULL);
> +	if (!tmdev->tm_map)
>  		return -ENODEV;
>  
>  	/*
> @@ -184,14 +184,14 @@ static int init_8960(struct tsens_device *tmdev)
>  	}
>  
>  	reg_cntl = SW_RST;
> -	ret = regmap_update_bits(tmdev->map, CNTL_ADDR, SW_RST, reg_cntl);
> +	ret = regmap_update_bits(tmdev->tm_map, CNTL_ADDR, SW_RST, reg_cntl);
>  	if (ret)
>  		return ret;
>  
>  	if (tmdev->num_sensors > 1) {
>  		reg_cntl |= SLP_CLK_ENA | (MEASURE_PERIOD << 18);
>  		reg_cntl &= ~SW_RST;
> -		ret = regmap_update_bits(tmdev->map, CONFIG_ADDR,
> +		ret = regmap_update_bits(tmdev->tm_map, CONFIG_ADDR,
>  					 CONFIG_MASK, CONFIG);
>  	} else {
>  		reg_cntl |= SLP_CLK_ENA_8660 | (MEASURE_PERIOD << 16);
> @@ -200,12 +200,12 @@ static int init_8960(struct tsens_device *tmdev)
>  	}
>  
>  	reg_cntl |= GENMASK(tmdev->num_sensors - 1, 0) << SENSOR0_SHIFT;
> -	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
>  	if (ret)
>  		return ret;
>  
>  	reg_cntl |= EN;
> -	ret = regmap_write(tmdev->map, CNTL_ADDR, reg_cntl);
> +	ret = regmap_write(tmdev->tm_map, CNTL_ADDR, reg_cntl);
>  	if (ret)
>  		return ret;
>  
> @@ -252,12 +252,12 @@ static int get_temp_8960(struct tsens_device *tmdev, int id, int *temp)
>  
>  	timeout = jiffies + usecs_to_jiffies(TIMEOUT_US);
>  	do {
> -		ret = regmap_read(tmdev->map, INT_STATUS_ADDR, &trdy);
> +		ret = regmap_read(tmdev->tm_map, INT_STATUS_ADDR, &trdy);
>  		if (ret)
>  			return ret;
>  		if (!(trdy & TRDY_MASK))
>  			continue;
> -		ret = regmap_read(tmdev->map, s->status, &code);
> +		ret = regmap_read(tmdev->tm_map, s->status, &code);
>  		if (ret)
>  			return ret;
>  		*temp = code_to_mdegC(code, s);
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 303e3fdaca98..0585084630b3 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -99,8 +99,7 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	int last_temp = 0, ret;
>  
>  	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
> -	ret = regmap_read(tmdev->map, status_reg, &code);
> -
> +	ret = regmap_read(tmdev->tm_map, status_reg, &code);
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;
> @@ -118,7 +117,7 @@ static const struct regmap_config tsens_config = {
>  
>  int __init init_common(struct tsens_device *tmdev)
>  {
> -	void __iomem *base;
> +	void __iomem *tm_base;
>  	struct resource *res;
>  	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
>  
> @@ -134,13 +133,13 @@ int __init init_common(struct tsens_device *tmdev)
>  	}
>  
>  	res = platform_get_resource(op, IORESOURCE_MEM, 0);
> -	base = devm_ioremap_resource(&op->dev, res);
> -	if (IS_ERR(base))
> -		return PTR_ERR(base);
> +	tm_base = devm_ioremap_resource(&op->dev, res);
> +	if (IS_ERR(tm_base))
> +		return PTR_ERR(tm_base);
>  
> -	tmdev->map = devm_regmap_init_mmio(tmdev->dev, base, &tsens_config);
> -	if (IS_ERR(tmdev->map))
> -		return PTR_ERR(tmdev->map);
> +	tmdev->tm_map = devm_regmap_init_mmio(tmdev->dev, tm_base, &tsens_config);
> +	if (IS_ERR(tmdev->tm_map))
> +		return PTR_ERR(tmdev->tm_map);
>  
>  	return 0;
>  }
> diff --git a/drivers/thermal/qcom/tsens-v2.c b/drivers/thermal/qcom/tsens-v2.c
> index 44da02f594ac..1bdef92e4521 100644
> --- a/drivers/thermal/qcom/tsens-v2.c
> +++ b/drivers/thermal/qcom/tsens-v2.c
> @@ -21,7 +21,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
>  	int ret;
>  
>  	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * 4;
> -	ret = regmap_read(tmdev->map, status_reg, &code);
> +	ret = regmap_read(tmdev->tm_map, status_reg, &code);
>  	if (ret)
>  		return ret;
>  	last_temp = code & LAST_TEMP_MASK;
> @@ -29,7 +29,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
>  		goto done;
>  
>  	/* Try a second time */
> -	ret = regmap_read(tmdev->map, status_reg, &code);
> +	ret = regmap_read(tmdev->tm_map, status_reg, &code);
>  	if (ret)
>  		return ret;
>  	if (code & STATUS_VALID_BIT) {
> @@ -40,7 +40,7 @@ static int get_temp_tsens_v2(struct tsens_device *tmdev, int id, int *temp)
>  	}
>  
>  	/* Try a third/last time */
> -	ret = regmap_read(tmdev->map, status_reg, &code);
> +	ret = regmap_read(tmdev->tm_map, status_reg, &code);
>  	if (ret)
>  		return ret;
>  	if (code & STATUS_VALID_BIT) {
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index 8207610f326a..58e98c4d3a8b 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -69,7 +69,7 @@ struct tsens_context {
>  struct tsens_device {
>  	struct device			*dev;
>  	u32				num_sensors;
> -	struct regmap			*map;
> +	struct regmap			*tm_map;
>  	u32				tm_offset;
>  	struct tsens_context		ctx;
>  	const struct tsens_ops		*ops;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 06/10] thermal: tsens: Add the SROT address map

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:38PM +0530, Amit Kucheria wrote:
> On platforms whose device trees specify two address spaces for TSENS, the
> second one points to the SROT registers. Initialise the SROT map on those
> platforms.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens-common.c | 14 ++++++++++++--
>  drivers/thermal/qcom/tsens.h        |  1 +
>  2 files changed, 13 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 0585084630b3..0b8a793f15f4 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -117,16 +117,26 @@ static const struct regmap_config tsens_config = {
>  
>  int __init init_common(struct tsens_device *tmdev)
>  {
> -	void __iomem *tm_base;
> +	void __iomem *tm_base, *srot_base;
>  	struct resource *res;
>  	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
>  
>  	if (!op)
>  		return -EINVAL;
>  
> -	/* The driver only uses the TM register address space for now */
>  	if (op->num_resources > 1) {
> +		/* DT with separate SROT and TM address space */
>  		tmdev->tm_offset = 0;
> +		res = platform_get_resource(op, IORESOURCE_MEM, 1);
> +		srot_base = devm_ioremap_resource(&op->dev, res);
> +		if (IS_ERR(srot_base))
> +			return PTR_ERR(srot_base);
> +
> +		tmdev->srot_map = devm_regmap_init_mmio(tmdev->dev,
> +							srot_base, &tsens_config);
> +		if (IS_ERR(tmdev->srot_map))
> +			return PTR_ERR(tmdev->srot_map);
> +
>  	} else {
>  		/* old DTs where SROT and TM were in a contiguous 2K block */
>  		tmdev->tm_offset = 0x1000;
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index 58e98c4d3a8b..b9c4bcf255fa 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -70,6 +70,7 @@ struct tsens_device {
>  	struct device			*dev;
>  	u32				num_sensors;
>  	struct regmap			*tm_map;
> +	struct regmap			*srot_map;
>  	u32				tm_offset;
>  	struct tsens_context		ctx;
>  	const struct tsens_ops		*ops;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 07/10] thermal: tsens: Check if the IP is correctly enabled by firmware

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:39PM +0530, Amit Kucheria wrote:
> The SROT registers are initialised by the secure firmware at boot. We
> don't have write access to the registers. Check if the block is enabled
> before continuing.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens-common.c | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
> 
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 0b8a793f15f4..d250b757d1f0 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -12,6 +12,11 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> +/* SROT */
> +#define CTRL_OFFSET		0x4
> +#define TSENS_EN		BIT(0)
> +
> +/* TM */
>  #define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
> @@ -119,6 +124,8 @@ int __init init_common(struct tsens_device *tmdev)
>  {
>  	void __iomem *tm_base, *srot_base;
>  	struct resource *res;
> +	u32 code;
> +	int ret;
>  	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
>  
>  	if (!op)
> @@ -151,5 +158,15 @@ int __init init_common(struct tsens_device *tmdev)
>  	if (IS_ERR(tmdev->tm_map))
>  		return PTR_ERR(tmdev->tm_map);
>  
> +	if (tmdev->srot_map) {
> +		ret = regmap_read(tmdev->srot_map, CTRL_OFFSET, &code);
> +		if (ret)
> +			return ret;
> +		if (!(code & TSENS_EN)) {
> +			dev_err(tmdev->dev, "tsens device is not enabled\n");
> +			return -ENODEV;
> +		}
> +	}
> +
>  	return 0;
>  }

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 08/10] thermal: tsens: Get rid of 'id' field

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:40PM +0530, Amit Kucheria wrote:
> The hw_id field in 'struct tsens_sensor' can do the job of tracking
> unique ids for each sensor connected to each tsens device instance. It
> also allows hw_ids to be overridden (e.g. 8916) in cases where some
> sensors in a sequence are disabled on a particular platform.
> 
> Use the hw_id field instead of the id field consistently across the
> tsens code.
> 
> While, we're at it, document the fields of struct tsens_sensor.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens.c |  5 ++---
>  drivers/thermal/qcom/tsens.h | 10 +++++++++-
>  2 files changed, 11 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> index 9a8e8f7b4ae1..fb728ec5d77f 100644
> --- a/drivers/thermal/qcom/tsens.c
> +++ b/drivers/thermal/qcom/tsens.c
> @@ -17,7 +17,7 @@ static int tsens_get_temp(void *data, int *temp)
>  	const struct tsens_sensor *s = data;
>  	struct tsens_device *tmdev = s->tmdev;
>  
> -	return tmdev->ops->get_temp(tmdev, s->id, temp);
> +	return tmdev->ops->get_temp(tmdev, s->hw_id, temp);
>  }
>  
>  static int tsens_get_trend(void *p, int trip, enum thermal_trend *trend)
> @@ -26,7 +26,7 @@ static int tsens_get_trend(void *p, int trip, enum thermal_trend *trend)
>  	struct tsens_device *tmdev = s->tmdev;
>  
>  	if (tmdev->ops->get_trend)
> -		return  tmdev->ops->get_trend(tmdev, s->id, trend);
> +		return  tmdev->ops->get_trend(tmdev, s->hw_id, trend);
>  
>  	return -ENOTSUPP;
>  }
> @@ -83,7 +83,6 @@ static int tsens_register(struct tsens_device *tmdev)
>  
>  	for (i = 0;  i < tmdev->num_sensors; i++) {
>  		tmdev->sensor[i].tmdev = tmdev;
> -		tmdev->sensor[i].id = i;
>  		tzd = devm_thermal_zone_of_sensor_register(tmdev->dev, i,
>  							   &tmdev->sensor[i],
>  							   &tsens_of_ops);
> diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> index b9c4bcf255fa..2a3174dfc1a9 100644
> --- a/drivers/thermal/qcom/tsens.h
> +++ b/drivers/thermal/qcom/tsens.h
> @@ -14,11 +14,19 @@
>  
>  struct tsens_device;
>  
> +/**
> + * struct tsens_sensor - sensor-specific data
> + * @tmdev: tsens device instance this sensor is connected to
> + * @tzd: thermal zone corresponding to this sensor
> + * @offset: offset from calibration data to convert ADC data to degrees
> + * @hw_id: unique sensor ID for each sensor connected to tsens device instance
> + * @slope: slope from calibration data to convert ADC data to degrees
> + * @status: 8960-specific status register addresses
> + */
>  struct tsens_sensor {
>  	struct tsens_device		*tmdev;
>  	struct thermal_zone_device	*tzd;
>  	int				offset;
> -	int				id;
>  	int				hw_id;
>  	int				slope;
>  	u32				status;

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 09/10] arm64: dts: qcom: Add reg-names for all tsens nodes

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:41PM +0530, Amit Kucheria wrote:
> Instead of showing up as thermal-sensor@<addr>, the nodes will show up as
> tsens0_tm, tsen1_tm, tsens1_srot, etc. in /proc/iomem making it easier to
> read.
> 
> IOW,
> 
> 0c222000-0c2221fe : thermal-sensor@c263000
> 0c223000-0c2231fe : thermal-sensor@c265000
> 0c263000-0c2631fe : thermal-sensor@c263000
> 0c265000-0c2651fe : thermal-sensor@c265000
> 
> becomes
> 
> 0c222000-0c2221fe : tsens0_srot
> 0c223000-0c2231fe : tsens1_srot
> 0c263000-0c2631fe : tsens0_tm
> 0c265000-0c2651fe : tsens1_tm
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 1 +
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
>  arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 ++
>  arch/arm64/boot/dts/qcom/sdm845.dtsi  | 2 ++
>  4 files changed, 6 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index 3c4b81c29798..64c9f81ddd90 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -431,6 +431,7 @@
>  			compatible = "qcom,msm8974-tsens";
>  			reg = <0xfc4a9000 0x1000>, /* TM */
>  			      <0xfc4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens_tm", "tsens_srot";
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
>  			#qcom,sensors = <11>;
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index abf84df5a7bc..4e6a5e462a91 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -778,6 +778,7 @@
>  			compatible = "qcom,msm8916-tsens";
>  			reg = <0x4a9000 0x1000>, /* TM */
>  			      <0x4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens_tm", "tsens_srot";
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
>  			#qcom,sensors = <5>;
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index c2dca3a30091..7e5982daa2ed 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -969,6 +969,7 @@
>  			compatible = "qcom,msm8996-tsens";
>  			reg = <0x4a9000 0x1000>, /* TM */
>  			      <0x4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens0_tm", "tsens0_srot";
>  			#qcom,sensors = <13>;
>  			#thermal-sensor-cells = <1>;
>  		};
> @@ -977,6 +978,7 @@
>  			compatible = "qcom,msm8996-tsens";
>  			reg = <0x4ad000 0x1000>, /* TM */
>  			      <0x4ac000 0x1000>; /* SROT */
> +			reg-names = "tsens1_tm", "tsens1_srot";
>  			#qcom,sensors = <8>;
>  			#thermal-sensor-cells = <1>;
>  		};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index f722785df26b..efd5d7abd1cd 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -1531,6 +1531,7 @@
>  			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>  			reg = <0xc263000 0x1ff>, /* TM */
>  			      <0xc222000 0x1ff>; /* SROT */
> +			reg-names = "tsens0_tm", "tsens0_srot";
>  			#qcom,sensors = <13>;
>  			#thermal-sensor-cells = <1>;
>  		};
> @@ -1539,6 +1540,7 @@
>  			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>  			reg = <0xc265000 0x1ff>, /* TM */
>  			      <0xc223000 0x1ff>; /* SROT */
> +			reg-names = "tsens1_tm", "tsens1_srot";
>  			#qcom,sensors = <8>;
>  			#thermal-sensor-cells = <1>;
>  		};

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v1 09/10] arm64: dts: qcom: Add reg-names for all tsens nodes

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:41PM +0530, Amit Kucheria wrote:
> Instead of showing up as thermal-sensor@<addr>, the nodes will show up as
> tsens0_tm, tsen1_tm, tsens1_srot, etc. in /proc/iomem making it easier to
> read.
> 
> IOW,
> 
> 0c222000-0c2221fe : thermal-sensor at c263000
> 0c223000-0c2231fe : thermal-sensor at c265000
> 0c263000-0c2631fe : thermal-sensor at c263000
> 0c265000-0c2651fe : thermal-sensor at c265000
> 
> becomes
> 
> 0c222000-0c2221fe : tsens0_srot
> 0c223000-0c2231fe : tsens1_srot
> 0c263000-0c2631fe : tsens0_tm
> 0c265000-0c2651fe : tsens1_tm
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 1 +
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
>  arch/arm64/boot/dts/qcom/msm8996.dtsi | 2 ++
>  arch/arm64/boot/dts/qcom/sdm845.dtsi  | 2 ++
>  4 files changed, 6 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index 3c4b81c29798..64c9f81ddd90 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -431,6 +431,7 @@
>  			compatible = "qcom,msm8974-tsens";
>  			reg = <0xfc4a9000 0x1000>, /* TM */
>  			      <0xfc4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens_tm", "tsens_srot";
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
>  			#qcom,sensors = <11>;
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index abf84df5a7bc..4e6a5e462a91 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -778,6 +778,7 @@
>  			compatible = "qcom,msm8916-tsens";
>  			reg = <0x4a9000 0x1000>, /* TM */
>  			      <0x4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens_tm", "tsens_srot";
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
>  			#qcom,sensors = <5>;
> diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> index c2dca3a30091..7e5982daa2ed 100644
> --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
> @@ -969,6 +969,7 @@
>  			compatible = "qcom,msm8996-tsens";
>  			reg = <0x4a9000 0x1000>, /* TM */
>  			      <0x4a8000 0x1000>; /* SROT */
> +			reg-names = "tsens0_tm", "tsens0_srot";
>  			#qcom,sensors = <13>;
>  			#thermal-sensor-cells = <1>;
>  		};
> @@ -977,6 +978,7 @@
>  			compatible = "qcom,msm8996-tsens";
>  			reg = <0x4ad000 0x1000>, /* TM */
>  			      <0x4ac000 0x1000>; /* SROT */
> +			reg-names = "tsens1_tm", "tsens1_srot";
>  			#qcom,sensors = <8>;
>  			#thermal-sensor-cells = <1>;
>  		};
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index f722785df26b..efd5d7abd1cd 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -1531,6 +1531,7 @@
>  			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>  			reg = <0xc263000 0x1ff>, /* TM */
>  			      <0xc222000 0x1ff>; /* SROT */
> +			reg-names = "tsens0_tm", "tsens0_srot";
>  			#qcom,sensors = <13>;
>  			#thermal-sensor-cells = <1>;
>  		};
> @@ -1539,6 +1540,7 @@
>  			compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
>  			reg = <0xc265000 0x1ff>, /* TM */
>  			      <0xc223000 0x1ff>; /* SROT */
> +			reg-names = "tsens1_tm", "tsens1_srot";
>  			#qcom,sensors = <8>;
>  			#thermal-sensor-cells = <1>;
>  		};

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 10/10] MAINTAINERS: Add entry for Qualcomm TSENS thermal drivers

[Matthias Kaehlcke]

On Thu, Aug 09, 2018 at 06:02:42PM +0530, Amit Kucheria wrote:
> Create an entry for the TSENS drivers and mark them as maintained
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  MAINTAINERS | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 68b4ff8ed205..ca6183d6d545 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11862,6 +11862,13 @@ L:	linux-arm-msm@vger.kernel.org
>  S:	Maintained
>  F:	drivers/iommu/qcom_iommu.c
>  
> +QUALCOMM TSENS THERMAL DRIVER
> +M:	Amit Kucheria <amit.kucheria@linaro.org>
> +L:	linux-pm@vger.kernel.org
> +L:	linux-arm-msm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/qcom/
> +
>  QUALCOMM VENUS VIDEO ACCELERATOR DRIVER
>  M:	Stanimir Varbanov <stanimir.varbanov@linaro.org>
>  L:	linux-media@vger.kernel.org

FWIW:

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

On Fri, Aug 10, 2018 at 12:41 AM Matthias Kaehlcke <mka@chromium.org> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> > We've earlier added support to split the register address space into TM
> > and SROT regions.
> >
> > Split up the regmap address space into two for the remaining platforms that
> > have a similar register layout and make corresponding changes to the
> > get_temp_common() function used by these platforms.
> >
> > Since tsens-common.c/init_common() currently only registers one address
> > space, the order is important (TM before SROT).  This is OK since the code
> > doesn't really use the SROT functionality yet.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
> >  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
> >  drivers/thermal/qcom/tsens-common.c   | 5 +++--
> >  3 files changed, 11 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > index d9019a49b292..3c4b81c29798 100644
> > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > @@ -427,11 +427,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@fc4a8000 {
> > +             tsens: thermal-sensor@fc4a9000 {
> >                       compatible = "qcom,msm8974-tsens";
> > -                     reg = <0xfc4a8000 0x2000>;
> > +                     reg = <0xfc4a9000 0x1000>, /* TM */
> > +                           <0xfc4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_calib>, <&tsens_backup>;
> >                       nvmem-cell-names = "calib", "calib_backup";
> > +                     #qcom,sensors = <11>;
>
> nit: adding the number of sensors isn't directly related and probably
> should be in a separate patch. Not important enough to re-spin just
> for this though ;-)

Hi Matthias,

Sometimes the urge to avoid frivolous patches takes over too strongly. :-)

I'll split it out in a respin. Thanks for the quick review of the series.

Regards,
Amit

> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > index cc1040eacdf5..abf84df5a7bc 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > @@ -774,11 +774,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@4a8000 {
> > +             tsens: thermal-sensor@4a9000 {
> >                       compatible = "qcom,msm8916-tsens";
> > -                     reg = <0x4a8000 0x2000>;
> > +                     reg = <0x4a9000 0x1000>, /* TM */
> > +                           <0x4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> >                       nvmem-cell-names = "calib", "calib_sel";
> > +                     #qcom,sensors = <5>;
>
> ditto
>
> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> > index 6207d8d92351..478739543bbc 100644
> > --- a/drivers/thermal/qcom/tsens-common.c
> > +++ b/drivers/thermal/qcom/tsens-common.c
> > @@ -21,7 +21,7 @@
> >  #include <linux/regmap.h>
> >  #include "tsens.h"
> >
> > -#define S0_ST_ADDR           0x1030
> > +#define STATUS_OFFSET                0x30
> >  #define SN_ADDR_OFFSET               0x4
> >  #define SN_ST_TEMP_MASK              0x3ff
> >  #define CAL_DEGC_PT1         30
> > @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
> >       unsigned int status_reg;
> >       int last_temp = 0, ret;
> >
> > -     status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> > +     status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
> >       ret = regmap_read(tmdev->map, status_reg, &code);
> > +
> >       if (ret)
> >               return ret;
> >       last_temp = code & SN_ST_TEMP_MASK;
>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

On Fri, Aug 10, 2018 at 12:41 AM Matthias Kaehlcke <mka@chromium.org> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> > We've earlier added support to split the register address space into TM
> > and SROT regions.
> >
> > Split up the regmap address space into two for the remaining platforms that
> > have a similar register layout and make corresponding changes to the
> > get_temp_common() function used by these platforms.
> >
> > Since tsens-common.c/init_common() currently only registers one address
> > space, the order is important (TM before SROT).  This is OK since the code
> > doesn't really use the SROT functionality yet.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
> >  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
> >  drivers/thermal/qcom/tsens-common.c   | 5 +++--
> >  3 files changed, 11 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > index d9019a49b292..3c4b81c29798 100644
> > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > @@ -427,11 +427,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@fc4a8000 {
> > +             tsens: thermal-sensor@fc4a9000 {
> >                       compatible = "qcom,msm8974-tsens";
> > -                     reg = <0xfc4a8000 0x2000>;
> > +                     reg = <0xfc4a9000 0x1000>, /* TM */
> > +                           <0xfc4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_calib>, <&tsens_backup>;
> >                       nvmem-cell-names = "calib", "calib_backup";
> > +                     #qcom,sensors = <11>;
>
> nit: adding the number of sensors isn't directly related and probably
> should be in a separate patch. Not important enough to re-spin just
> for this though ;-)

Hi Matthias,

Sometimes the urge to avoid frivolous patches takes over too strongly. :-)

I'll split it out in a respin. Thanks for the quick review of the series.

Regards,
Amit

> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > index cc1040eacdf5..abf84df5a7bc 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > @@ -774,11 +774,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@4a8000 {
> > +             tsens: thermal-sensor@4a9000 {
> >                       compatible = "qcom,msm8916-tsens";
> > -                     reg = <0x4a8000 0x2000>;
> > +                     reg = <0x4a9000 0x1000>, /* TM */
> > +                           <0x4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> >                       nvmem-cell-names = "calib", "calib_sel";
> > +                     #qcom,sensors = <5>;
>
> ditto
>
> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> > index 6207d8d92351..478739543bbc 100644
> > --- a/drivers/thermal/qcom/tsens-common.c
> > +++ b/drivers/thermal/qcom/tsens-common.c
> > @@ -21,7 +21,7 @@
> >  #include <linux/regmap.h>
> >  #include "tsens.h"
> >
> > -#define S0_ST_ADDR           0x1030
> > +#define STATUS_OFFSET                0x30
> >  #define SN_ADDR_OFFSET               0x4
> >  #define SN_ST_TEMP_MASK              0x3ff
> >  #define CAL_DEGC_PT1         30
> > @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
> >       unsigned int status_reg;
> >       int last_temp = 0, ret;
> >
> > -     status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> > +     status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
> >       ret = regmap_read(tmdev->map, status_reg, &code);
> > +
> >       if (ret)
> >               return ret;
> >       last_temp = code & SN_ST_TEMP_MASK;
>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

On Fri, Aug 10, 2018 at 12:41 AM Matthias Kaehlcke <mka@chromium.org> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> > We've earlier added support to split the register address space into TM
> > and SROT regions.
> >
> > Split up the regmap address space into two for the remaining platforms that
> > have a similar register layout and make corresponding changes to the
> > get_temp_common() function used by these platforms.
> >
> > Since tsens-common.c/init_common() currently only registers one address
> > space, the order is important (TM before SROT).  This is OK since the code
> > doesn't really use the SROT functionality yet.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
> >  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
> >  drivers/thermal/qcom/tsens-common.c   | 5 +++--
> >  3 files changed, 11 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > index d9019a49b292..3c4b81c29798 100644
> > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > @@ -427,11 +427,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor at fc4a8000 {
> > +             tsens: thermal-sensor at fc4a9000 {
> >                       compatible = "qcom,msm8974-tsens";
> > -                     reg = <0xfc4a8000 0x2000>;
> > +                     reg = <0xfc4a9000 0x1000>, /* TM */
> > +                           <0xfc4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_calib>, <&tsens_backup>;
> >                       nvmem-cell-names = "calib", "calib_backup";
> > +                     #qcom,sensors = <11>;
>
> nit: adding the number of sensors isn't directly related and probably
> should be in a separate patch. Not important enough to re-spin just
> for this though ;-)

Hi Matthias,

Sometimes the urge to avoid frivolous patches takes over too strongly. :-)

I'll split it out in a respin. Thanks for the quick review of the series.

Regards,
Amit

> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > index cc1040eacdf5..abf84df5a7bc 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > @@ -774,11 +774,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor at 4a8000 {
> > +             tsens: thermal-sensor at 4a9000 {
> >                       compatible = "qcom,msm8916-tsens";
> > -                     reg = <0x4a8000 0x2000>;
> > +                     reg = <0x4a9000 0x1000>, /* TM */
> > +                           <0x4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> >                       nvmem-cell-names = "calib", "calib_sel";
> > +                     #qcom,sensors = <5>;
>
> ditto
>
> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> > index 6207d8d92351..478739543bbc 100644
> > --- a/drivers/thermal/qcom/tsens-common.c
> > +++ b/drivers/thermal/qcom/tsens-common.c
> > @@ -21,7 +21,7 @@
> >  #include <linux/regmap.h>
> >  #include "tsens.h"
> >
> > -#define S0_ST_ADDR           0x1030
> > +#define STATUS_OFFSET                0x30
> >  #define SN_ADDR_OFFSET               0x4
> >  #define SN_ST_TEMP_MASK              0x3ff
> >  #define CAL_DEGC_PT1         30
> > @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
> >       unsigned int status_reg;
> >       int last_temp = 0, ret;
> >
> > -     status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> > +     status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
> >       ret = regmap_read(tmdev->map, status_reg, &code);
> > +
> >       if (ret)
> >               return ret;
> >       last_temp = code & SN_ST_TEMP_MASK;
>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

Re: [PATCH v1 02/10] dt-bindings: thermal: Fix a typo in documentation

[Rob Herring]

On Thu, Aug 09, 2018 at 06:02:34PM +0530, Amit Kucheria wrote:
> c(1) + x(1) was actually meant to be c(1) * x(1).
> 
> While we're at it, add some brackets to make it nicer to read.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  Documentation/devicetree/bindings/thermal/thermal.txt | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v1 10/10] MAINTAINERS: Add entry for Qualcomm TSENS thermal drivers

[Rajendra Nayak]

On 8/9/2018 6:02 PM, Amit Kucheria wrote:
> Create an entry for the TSENS drivers and mark them as maintained
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>

Thanks Amit for signing up to maintain this driver.

Acked-by: Rajendra Nayak <rnayak@codeaurora.org>

> ---
>   MAINTAINERS | 7 +++++++
>   1 file changed, 7 insertions(+)
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 68b4ff8ed205..ca6183d6d545 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11862,6 +11862,13 @@ L:	linux-arm-msm@vger.kernel.org
>   S:	Maintained
>   F:	drivers/iommu/qcom_iommu.c
>   
> +QUALCOMM TSENS THERMAL DRIVER
> +M:	Amit Kucheria <amit.kucheria@linaro.org>
> +L:	linux-pm@vger.kernel.org
> +L:	linux-arm-msm@vger.kernel.org
> +S:	Maintained
> +F:	drivers/thermal/qcom/
> +
>   QUALCOMM VENUS VIDEO ACCELERATOR DRIVER
>   M:	Stanimir Varbanov <stanimir.varbanov@linaro.org>
>   L:	linux-media@vger.kernel.org
> 

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Eduardo Valentin]

hello,

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--



>  drivers/thermal/qcom/tsens-common.c   | 5 +++--


Can you please resend this with two separate patches, one with
the driver changes another for the dts(i) changes. Just that
I prefer taking only the driver changes once accepting the
dts changes. Makes merging easier to avoid conflicts when sending
pulls.

Thanks.
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@fc4a8000 {
> +		tsens: thermal-sensor@fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@4a8000 {
> +		tsens: thermal-sensor@4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;
> -- 
> 2.17.1
> 

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Eduardo Valentin]

hello,

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--



>  drivers/thermal/qcom/tsens-common.c   | 5 +++--


Can you please resend this with two separate patches, one with
the driver changes another for the dts(i) changes. Just that
I prefer taking only the driver changes once accepting the
dts changes. Makes merging easier to avoid conflicts when sending
pulls.

Thanks.
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at fc4a8000 {
> +		tsens: thermal-sensor at fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at 4a8000 {
> +		tsens: thermal-sensor at 4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;
> -- 
> 2.17.1
> 

Re: [PATCH v1 02/10] dt-bindings: thermal: Fix a typo in documentation

[Eduardo Valentin]

On Thu, Aug 09, 2018 at 06:02:34PM +0530, Amit Kucheria wrote:
> c(1) + x(1) was actually meant to be c(1) * x(1).
> 
> While we're at it, add some brackets to make it nicer to read.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  Documentation/devicetree/bindings/thermal/thermal.txt | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
> index cc553f0952c5..751104213d08 100644
> --- a/Documentation/devicetree/bindings/thermal/thermal.txt
> +++ b/Documentation/devicetree/bindings/thermal/thermal.txt
> @@ -152,7 +152,7 @@ Optional property:
>    Elem size: one cell	the sensors listed in the thermal-sensors property.
>    Elem type: signed	Coefficients defaults to 1, in case this property
>  			is not specified. A simple linear polynomial is used:
> -			Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn.
> +			Z = (c0 * x0) + (c1 * x1) + ... + (c(n-1) * x(n-1)) + cn.

To be honest, I would prefer if this looks like:
+			Z = c0 * x0 + c1 * x1 + ... + c(n-1) * x(n-1) + cn.

The extra bracketing seams unnecessary confusion

>  
>  			The coefficients are ordered and they match with sensors
>  			by means of sensor ID. Additional coefficients are
> -- 
> 2.17.1
> 

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Eduardo Valentin]

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
>  drivers/thermal/qcom/tsens-common.c   | 5 +++--
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@fc4a8000 {
> +		tsens: thermal-sensor@fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor@4a8000 {
> +		tsens: thermal-sensor@4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;
>  			#thermal-sensor-cells = <1>;

Looking closer to this, I fail to remember the reasoning why
#qcom,sensors property was needed.

>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;
> -- 
> 2.17.1
> 

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Eduardo Valentin]

On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> We've earlier added support to split the register address space into TM
> and SROT regions.
> 
> Split up the regmap address space into two for the remaining platforms that
> have a similar register layout and make corresponding changes to the
> get_temp_common() function used by these platforms.
> 
> Since tsens-common.c/init_common() currently only registers one address
> space, the order is important (TM before SROT).  This is OK since the code
> doesn't really use the SROT functionality yet.
> 
> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
>  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
>  drivers/thermal/qcom/tsens-common.c   | 5 +++--
>  3 files changed, 11 insertions(+), 6 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> index d9019a49b292..3c4b81c29798 100644
> --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> @@ -427,11 +427,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at fc4a8000 {
> +		tsens: thermal-sensor at fc4a9000 {
>  			compatible = "qcom,msm8974-tsens";
> -			reg = <0xfc4a8000 0x2000>;
> +			reg = <0xfc4a9000 0x1000>, /* TM */
> +			      <0xfc4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
>  			nvmem-cell-names = "calib", "calib_backup";
> +			#qcom,sensors = <11>;
>  			#thermal-sensor-cells = <1>;
>  		};
>  
> diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> index cc1040eacdf5..abf84df5a7bc 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> @@ -774,11 +774,13 @@
>  			};
>  		};
>  
> -		tsens: thermal-sensor at 4a8000 {
> +		tsens: thermal-sensor at 4a9000 {
>  			compatible = "qcom,msm8916-tsens";
> -			reg = <0x4a8000 0x2000>;
> +			reg = <0x4a9000 0x1000>, /* TM */
> +			      <0x4a8000 0x1000>; /* SROT */
>  			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
>  			nvmem-cell-names = "calib", "calib_sel";
> +			#qcom,sensors = <5>;
>  			#thermal-sensor-cells = <1>;

Looking closer to this, I fail to remember the reasoning why
#qcom,sensors property was needed.

>  		};
>  
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 6207d8d92351..478739543bbc 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -21,7 +21,7 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> -#define S0_ST_ADDR		0x1030
> +#define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
>  #define CAL_DEGC_PT1		30
> @@ -107,8 +107,9 @@ int get_temp_common(struct tsens_device *tmdev, int id, int *temp)
>  	unsigned int status_reg;
>  	int last_temp = 0, ret;
>  
> -	status_reg = S0_ST_ADDR + s->hw_id * SN_ADDR_OFFSET;
> +	status_reg = tmdev->tm_offset + STATUS_OFFSET + s->hw_id * SN_ADDR_OFFSET;
>  	ret = regmap_read(tmdev->map, status_reg, &code);
> +
>  	if (ret)
>  		return ret;
>  	last_temp = code & SN_ST_TEMP_MASK;
> -- 
> 2.17.1
> 

Re: [PATCH v1 07/10] thermal: tsens: Check if the IP is correctly enabled by firmware

[Eduardo Valentin]

On Thu, Aug 09, 2018 at 06:02:39PM +0530, Amit Kucheria wrote:
> The SROT registers are initialised by the secure firmware at boot. We
> don't have write access to the registers. Check if the block is enabled
> before continuing.
> 

Should this be merged to patch 6?

> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
>  drivers/thermal/qcom/tsens-common.c | 17 +++++++++++++++++
>  1 file changed, 17 insertions(+)
> 
> diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> index 0b8a793f15f4..d250b757d1f0 100644
> --- a/drivers/thermal/qcom/tsens-common.c
> +++ b/drivers/thermal/qcom/tsens-common.c
> @@ -12,6 +12,11 @@
>  #include <linux/regmap.h>
>  #include "tsens.h"
>  
> +/* SROT */
> +#define CTRL_OFFSET		0x4
> +#define TSENS_EN		BIT(0)
> +
> +/* TM */
>  #define STATUS_OFFSET		0x30
>  #define SN_ADDR_OFFSET		0x4
>  #define SN_ST_TEMP_MASK		0x3ff
> @@ -119,6 +124,8 @@ int __init init_common(struct tsens_device *tmdev)
>  {
>  	void __iomem *tm_base, *srot_base;
>  	struct resource *res;
> +	u32 code;
> +	int ret;
>  	struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
>  
>  	if (!op)
> @@ -151,5 +158,15 @@ int __init init_common(struct tsens_device *tmdev)
>  	if (IS_ERR(tmdev->tm_map))
>  		return PTR_ERR(tmdev->tm_map);
>  
> +	if (tmdev->srot_map) {
> +		ret = regmap_read(tmdev->srot_map, CTRL_OFFSET, &code);
> +		if (ret)
> +			return ret;
> +		if (!(code & TSENS_EN)) {
> +			dev_err(tmdev->dev, "tsens device is not enabled\n");
> +			return -ENODEV;
> +		}
> +	}
> +
>  	return 0;
>  }
> -- 
> 2.17.1
> 

Re: [PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

On Sat, Aug 25, 2018 at 4:58 AM Eduardo Valentin <edubezval@gmail.com> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> > We've earlier added support to split the register address space into TM
> > and SROT regions.
> >
> > Split up the regmap address space into two for the remaining platforms that
> > have a similar register layout and make corresponding changes to the
> > get_temp_common() function used by these platforms.
> >
> > Since tsens-common.c/init_common() currently only registers one address
> > space, the order is important (TM before SROT).  This is OK since the code
> > doesn't really use the SROT functionality yet.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
> >  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
> >  drivers/thermal/qcom/tsens-common.c   | 5 +++--
> >  3 files changed, 11 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > index d9019a49b292..3c4b81c29798 100644
> > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > @@ -427,11 +427,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@fc4a8000 {
> > +             tsens: thermal-sensor@fc4a9000 {
> >                       compatible = "qcom,msm8974-tsens";
> > -                     reg = <0xfc4a8000 0x2000>;
> > +                     reg = <0xfc4a9000 0x1000>, /* TM */
> > +                           <0xfc4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_calib>, <&tsens_backup>;
> >                       nvmem-cell-names = "calib", "calib_backup";
> > +                     #qcom,sensors = <11>;
> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > index cc1040eacdf5..abf84df5a7bc 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > @@ -774,11 +774,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor@4a8000 {
> > +             tsens: thermal-sensor@4a9000 {
> >                       compatible = "qcom,msm8916-tsens";
> > -                     reg = <0x4a8000 0x2000>;
> > +                     reg = <0x4a9000 0x1000>, /* TM */
> > +                           <0x4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> >                       nvmem-cell-names = "calib", "calib_sel";
> > +                     #qcom,sensors = <5>;
> >                       #thermal-sensor-cells = <1>;
>
> Looking closer to this, I fail to remember the reasoning why
> #qcom,sensors property was needed.

It is necessary for platforms that have multiple TSENS blocks. This
then allows us to specify the number of connected sensors per block.
See commit 6d7c70d1cd65 ("thermal: qcom: tsens: Allow number of
sensors to come from DT") for details.

As requested by Matthias, I'm moving this bit to its own patch in v2.

Regards,
Amit

[PATCH v1 01/10] arm/arm64: dts: msm8974/msm8916: thermal: Split address space into two

[Amit Kucheria]

On Sat, Aug 25, 2018 at 4:58 AM Eduardo Valentin <edubezval@gmail.com> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:33PM +0530, Amit Kucheria wrote:
> > We've earlier added support to split the register address space into TM
> > and SROT regions.
> >
> > Split up the regmap address space into two for the remaining platforms that
> > have a similar register layout and make corresponding changes to the
> > get_temp_common() function used by these platforms.
> >
> > Since tsens-common.c/init_common() currently only registers one address
> > space, the order is important (TM before SROT).  This is OK since the code
> > doesn't really use the SROT functionality yet.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  arch/arm/boot/dts/qcom-msm8974.dtsi   | 6 ++++--
> >  arch/arm64/boot/dts/qcom/msm8916.dtsi | 6 ++++--
> >  drivers/thermal/qcom/tsens-common.c   | 5 +++--
> >  3 files changed, 11 insertions(+), 6 deletions(-)
> >
> > diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > index d9019a49b292..3c4b81c29798 100644
> > --- a/arch/arm/boot/dts/qcom-msm8974.dtsi
> > +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
> > @@ -427,11 +427,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor at fc4a8000 {
> > +             tsens: thermal-sensor at fc4a9000 {
> >                       compatible = "qcom,msm8974-tsens";
> > -                     reg = <0xfc4a8000 0x2000>;
> > +                     reg = <0xfc4a9000 0x1000>, /* TM */
> > +                           <0xfc4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_calib>, <&tsens_backup>;
> >                       nvmem-cell-names = "calib", "calib_backup";
> > +                     #qcom,sensors = <11>;
> >                       #thermal-sensor-cells = <1>;
> >               };
> >
> > diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > index cc1040eacdf5..abf84df5a7bc 100644
> > --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
> > @@ -774,11 +774,13 @@
> >                       };
> >               };
> >
> > -             tsens: thermal-sensor at 4a8000 {
> > +             tsens: thermal-sensor at 4a9000 {
> >                       compatible = "qcom,msm8916-tsens";
> > -                     reg = <0x4a8000 0x2000>;
> > +                     reg = <0x4a9000 0x1000>, /* TM */
> > +                           <0x4a8000 0x1000>; /* SROT */
> >                       nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
> >                       nvmem-cell-names = "calib", "calib_sel";
> > +                     #qcom,sensors = <5>;
> >                       #thermal-sensor-cells = <1>;
>
> Looking closer to this, I fail to remember the reasoning why
> #qcom,sensors property was needed.

It is necessary for platforms that have multiple TSENS blocks. This
then allows us to specify the number of connected sensors per block.
See commit 6d7c70d1cd65 ("thermal: qcom: tsens: Allow number of
sensors to come from DT") for details.

As requested by Matthias, I'm moving this bit to its own patch in v2.

Regards,
Amit

Re: [PATCH v1 07/10] thermal: tsens: Check if the IP is correctly enabled by firmware

[Amit Kucheria]

On Sat, Aug 25, 2018 at 5:00 AM Eduardo Valentin <edubezval@gmail.com> wrote:
>
> On Thu, Aug 09, 2018 at 06:02:39PM +0530, Amit Kucheria wrote:
> > The SROT registers are initialised by the secure firmware at boot. We
> > don't have write access to the registers. Check if the block is enabled
> > before continuing.
> >
>
> Should this be merged to patch 6?

I've kept it separate because this 'enable' check could've been added
to the old code as well, without the separate SROT mapping in patch 6.
So in my mind, they're two different things: splitting the address map
and adding the 'enable' check and I'd prefer to keep it as it is.

> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > ---
> >  drivers/thermal/qcom/tsens-common.c | 17 +++++++++++++++++
> >  1 file changed, 17 insertions(+)
> >
> > diff --git a/drivers/thermal/qcom/tsens-common.c b/drivers/thermal/qcom/tsens-common.c
> > index 0b8a793f15f4..d250b757d1f0 100644
> > --- a/drivers/thermal/qcom/tsens-common.c
> > +++ b/drivers/thermal/qcom/tsens-common.c
> > @@ -12,6 +12,11 @@
> >  #include <linux/regmap.h>
> >  #include "tsens.h"
> >
> > +/* SROT */
> > +#define CTRL_OFFSET          0x4
> > +#define TSENS_EN             BIT(0)
> > +
> > +/* TM */
> >  #define STATUS_OFFSET                0x30
> >  #define SN_ADDR_OFFSET               0x4
> >  #define SN_ST_TEMP_MASK              0x3ff
> > @@ -119,6 +124,8 @@ int __init init_common(struct tsens_device *tmdev)
> >  {
> >       void __iomem *tm_base, *srot_base;
> >       struct resource *res;
> > +     u32 code;
> > +     int ret;
> >       struct platform_device *op = of_find_device_by_node(tmdev->dev->of_node);
> >
> >       if (!op)
> > @@ -151,5 +158,15 @@ int __init init_common(struct tsens_device *tmdev)
> >       if (IS_ERR(tmdev->tm_map))
> >               return PTR_ERR(tmdev->tm_map);
> >
> > +     if (tmdev->srot_map) {
> > +             ret = regmap_read(tmdev->srot_map, CTRL_OFFSET, &code);
> > +             if (ret)
> > +                     return ret;
> > +             if (!(code & TSENS_EN)) {
> > +                     dev_err(tmdev->dev, "tsens device is not enabled\n");
> > +                     return -ENODEV;
> > +             }
> > +     }
> > +
> >       return 0;
> >  }
> > --
> > 2.17.1
> >

Re: [PATCH v1 02/10] dt-bindings: thermal: Fix a typo in documentation

[Daniel Lezcano]

On 25/08/2018 01:24, Eduardo Valentin wrote:
> On Thu, Aug 09, 2018 at 06:02:34PM +0530, Amit Kucheria wrote:
>> c(1) + x(1) was actually meant to be c(1) * x(1).
>>
>> While we're at it, add some brackets to make it nicer to read.
>>
>> Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
>> ---
>>  Documentation/devicetree/bindings/thermal/thermal.txt | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt
>> index cc553f0952c5..751104213d08 100644
>> --- a/Documentation/devicetree/bindings/thermal/thermal.txt
>> +++ b/Documentation/devicetree/bindings/thermal/thermal.txt
>> @@ -152,7 +152,7 @@ Optional property:
>>    Elem size: one cell	the sensors listed in the thermal-sensors property.
>>    Elem type: signed	Coefficients defaults to 1, in case this property
>>  			is not specified. A simple linear polynomial is used:
>> -			Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn.
>> +			Z = (c0 * x0) + (c1 * x1) + ... + (c(n-1) * x(n-1)) + cn.
> 
> To be honest, I would prefer if this looks like:
> +			Z = c0 * x0 + c1 * x1 + ... + c(n-1) * x(n-1) + cn.
> 
> The extra bracketing seams unnecessary confusion

I agree, the brackets don't change the computation ordering, they are
pointless.


-- 
 <http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog