* Mitac 8252D hda_intel
@ 2007-11-13 20:51 glv
2007-11-15 11:40 ` Takashi Iwai
0 siblings, 1 reply; 5+ messages in thread
From: glv @ 2007-11-13 20:51 UTC (permalink / raw)
To: alsa-devel
(Second attempt, hope this works)
Hello,
I have a Mitac 8252D computer with hda_intel, it has 3 sockets in front:
microphone, audio(headphones)and S/PDIF.
When using 5.1 the manual says:
Microphone: rear speakers
Audio: front speakers
S/PDIF: center and subwoofer
Modprobing without any options gives me sound to the headphone and digital
socket and
Modprobing with model=6stack-hp gives me sound to the speakers to but they
stay on when headph. are pluged in
Output from alsa-info.sh:
http://pastebin.ca/772406
Output from lspci -vv:
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller (rev 03)
Subsystem: Mitac Unknown device 8253
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
thank you.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Mitac 8252D hda_intel
2007-11-13 20:51 Mitac 8252D hda_intel glv
@ 2007-11-15 11:40 ` Takashi Iwai
2007-11-15 16:53 ` Tobin Davis
2007-11-15 19:49 ` glv
0 siblings, 2 replies; 5+ messages in thread
From: Takashi Iwai @ 2007-11-15 11:40 UTC (permalink / raw)
To: glv; +Cc: alsa-devel
At Tue, 13 Nov 2007 20:51:10 +0000,
glv wrote:
>
> (Second attempt, hope this works)
>
> Hello,
> I have a Mitac 8252D computer with hda_intel, it has 3 sockets in front:
> microphone, audio(headphones)and S/PDIF.
> When using 5.1 the manual says:
> Microphone: rear speakers
> Audio: front speakers
> S/PDIF: center and subwoofer
> Modprobing without any options gives me sound to the headphone and digital
> socket and
> Modprobing with model=6stack-hp gives me sound to the speakers to but they
> stay on when headph. are pluged in
>
> Output from alsa-info.sh:
> http://pastebin.ca/772406
Posting here, at least the content of /proc/asound/codec#*, would be
more helpful.
Is the SPDIF optical? If yes, the device should have two output pins,
one for SPDIF and one for CLFE. That'll be relatively easy.
If the SPDIF output is really shared, it means that the digital audio
out widget is used for the analog out, too. It's not implemented in
other devices, so the change would be somehow unique for this device.
thanks,
Takashi
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Mitac 8252D hda_intel
2007-11-15 11:40 ` Takashi Iwai
@ 2007-11-15 16:53 ` Tobin Davis
2007-11-15 19:49 ` glv
1 sibling, 0 replies; 5+ messages in thread
From: Tobin Davis @ 2007-11-15 16:53 UTC (permalink / raw)
To: Takashi Iwai; +Cc: glv, alsa-devel
On Thu, 2007-11-15 at 12:40 +0100, Takashi Iwai wrote:
> At Tue, 13 Nov 2007 20:51:10 +0000,
> glv wrote:
> >
> > (Second attempt, hope this works)
> >
> > Hello,
> > I have a Mitac 8252D computer with hda_intel, it has 3 sockets in front:
> > microphone, audio(headphones)and S/PDIF.
> > When using 5.1 the manual says:
> > Microphone: rear speakers
> > Audio: front speakers
> > S/PDIF: center and subwoofer
> > Modprobing without any options gives me sound to the headphone and digital
> > socket and
> > Modprobing with model=6stack-hp gives me sound to the speakers to but they
> > stay on when headph. are pluged in
> >
> > Output from alsa-info.sh:
> > http://pastebin.ca/772406
>
> Posting here, at least the content of /proc/asound/codec#*, would be
> more helpful.
The link he posted is from alsa-info.sh, a script written by wishie on
#alsa irc and heavily promoted by me. It has the codec output, as
well as everything else needed to determine how his system is
configured.
> Is the SPDIF optical? If yes, the device should have two output pins,
> one for SPDIF and one for CLFE. That'll be relatively easy.
> If the SPDIF output is really shared, it means that the digital audio
> out widget is used for the analog out, too. It's not implemented in
> other devices, so the change would be somehow unique for this device.
Actually, a lot of laptops (mine included) have a mini-TOS plug
combined with a headphone plug, so it is possible for an optical jack
and an analog jack to share space. Plugging in an spdif cable with
mini-tos adapter activates the hp-detect routine. I haven't tested
spdif output yet (need a good stereo receiver), but that's the
principle behind it.
--
Tobin Davis
In case of atomic attack, the federal ruling against prayer in schools
will be temporarily canceled.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Mitac 8252D hda_intel
2007-11-15 11:40 ` Takashi Iwai
2007-11-15 16:53 ` Tobin Davis
@ 2007-11-15 19:49 ` glv
1 sibling, 0 replies; 5+ messages in thread
From: glv @ 2007-11-15 19:49 UTC (permalink / raw)
To: alsa-devel
Thank you for your reply,
Þann Fimmtudagur 15 nóvember 2007 skrifaði Takashi Iwai:
>
> Posting here, at least the content of /proc/asound/codec#*, would be
> more helpful.
>
Here is the output from /proc/asound/card0/codec#0:
Codec: Realtek ALC883
Address: 0
Vendor Id: 0x10ec0883
Subsystem Id: 0x10718253
Revision Id: 0x100002
No Modem Function Group found
Default PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x02 [Audio Output] wcaps 0x11: Stereo
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x03 [Audio Output] wcaps 0x11: Stereo
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x04 [Audio Output] wcaps 0x11: Stereo
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x05 [Audio Output] wcaps 0x11: Stereo
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0x1e]: 16 20 24 32
formats [0x1]: PCM
Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x08 [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x08, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80]
PCM:
rates [0x160]: 44100 48000 96000
bits [0x6]: 16 20
formats [0x1]: PCM
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x08, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80]
PCM:
rates [0x160]: 44100 48000 96000
bits [0x6]: 16 20
formats [0x1]: PCM
Connection: 1
0x22
Node 0x0a [Audio Input] wcaps 0x100391: Stereo Digital
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0x1e]: 16 20 24 32
formats [0x1]: PCM
Connection: 1
0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x1f 0x1f] [0x9f 0x9f] [0x80 0x80] [0x80 0x80] [0x80 0x80]
[0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Connection: 10
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17
Node 0x0c [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0
Amp-Out vals: [0x1f 0x1f]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0
Amp-Out vals: [0x1f 0x1f]
Connection: 2
0x03 0x0b
Node 0x0e [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x04 0x0b
Node 0x0f [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x05 0x0b
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x14 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x083e: IN OUT HP Detect
Pin Default 0x99138110: [Fixed] Speaker at Int ATAPI
Conn = ATAPI, Color = Purple
Pin-ctls: 0x20: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x083e: IN OUT HP Detect
Pin Default 0x0121401f: [Jack] HP Out at Ext Rear
Conn = 1/8, Color = Green
Pin-ctls: 0xc0: OUT HP
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x16 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x083e: IN OUT HP Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Connection: 5
0x0c 0x0d 0x0e* 0x0f 0x26
Node 0x17 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x083e: IN OUT HP Detect
Pin Default 0x99138120: [Fixed] Speaker at Int ATAPI
Conn = ATAPI, Color = Purple
Pin-ctls: 0x20: IN
Connection: 5
0x0c 0x0d 0x0e 0x0f* 0x26
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x03 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08173e: IN OUT HP Detect
Pin Default 0x01a19c50: [Jack] Mic at Ext Rear
Conn = 1/8, Color = Pink
Pin-ctls: 0x24: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x01 0x01] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08173e: IN OUT HP Detect
Pin Default 0x99a38960: [Fixed] Mic at Int ATAPI
Conn = ATAPI, Color = Purple
Pin-ctls: 0x24: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x08173e: IN OUT HP Detect
Pin Default 0x01013021: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Blue
Pin-ctls: 0x40: OUT
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08173e: IN OUT HP Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1c [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Node 0x1d [Pin Complex] wcaps 0x400000: Mono
Pincap 0x0820: IN
Pin Default 0x40138205: [N/A] Speaker at Ext N/A
Conn = ATAPI, Color = Purple
Pin-ctls: 0x00:
Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital
Pincap 0x0810: OUT
Pin Default 0x01443140: [Jack] SPDIF Out at Ext Rear
Conn = RCA, Color = Blue
Pin-ctls: 0x00:
Connection: 1
0x06
Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital
Pincap 0x0820: IN
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
Pin-ctls: 0x00:
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x80 0x80]
[0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Amp-Out caps: N/A
Amp-Out vals: [0x00 0x00]
Connection: 11
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b
Node 0x23 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x00 0x00]
[0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80]
Amp-Out caps: N/A
Amp-Out vals: [0x00 0x00]
Connection: 11
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b
Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x25 [Audio Output] wcaps 0x11: Stereo
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Node 0x26 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x25 0x0b
here is card#1:
Codec: Conexant ID 2c06
Address: 1
Vendor Id: 0x14f12c06
Subsystem Id: 0x14f10000
Revision Id: 0x100000
Modem Function Group: 0x2
> Is the SPDIF optical? If yes, the device should have two output pins,
> one for SPDIF and one for CLFE. That'll be relatively easy.
> If the SPDIF output is really shared, it means that the digital audio
> out widget is used for the analog out, too. It's not implemented in
> other devices, so the change would be somehow unique for this device.
I have an iec958 switch that I can use to turn on a red light in the plug
hole, but it has no effect on if I plug in headphones I can allways hear
them, allthough somewhat lower than in the headphone jack.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: Mitac 8252D hda_intel
2007-11-13 18:42 Query regarding snd_pcm_lib_preallocate_pages_for_all() Pharaoh .
@ 2007-11-13 20:31 ` glv
0 siblings, 0 replies; 5+ messages in thread
From: glv @ 2007-11-13 20:31 UTC (permalink / raw)
To: alsa-devel
Hello,
I have a Mitac 8252D computer with hda_intel, it has 3 sockets in front:
microphone, audio(headphones)and S/PDIF.
When using 5.1 the manual says:
Microphone: rear speakers
Audio: front speakers
S/PDIF: center and subwoofer
Modprobing without any options gives me sound to the headphone and digital
socket and
Modprobing with model=6stack-hp gives me sound to the speakers to but they
stay on when headph. are pluged in
Output from alsa-info.sh:
http://pastebin.ca/772406
Output from lspci -vv:
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller (rev 03)
Subsystem: Mitac Unknown device 8253
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
thank you.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2007-11-15 19:50 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2007-11-13 20:51 Mitac 8252D hda_intel glv
2007-11-15 11:40 ` Takashi Iwai
2007-11-15 16:53 ` Tobin Davis
2007-11-15 19:49 ` glv
-- strict thread matches above, loose matches on Subject: below --
2007-11-13 18:42 Query regarding snd_pcm_lib_preallocate_pages_for_all() Pharaoh .
2007-11-13 20:31 ` Mitac 8252D hda_intel glv
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.