* [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus
[not found] <20220520120449.12996-1-ae40515.ref@yahoo.com.tw>
@ 2022-05-20 12:04 ` Alec Su
2022-05-20 12:04 ` [PATCH v3 1/2] dt-bindings: arm: qcom: Document xiaomi,natrium board Alec Su
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Alec Su @ 2022-05-20 12:04 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt, krzysztof.kozlowski+dt, sboyd
Cc: linux-arm-msm, devicetree, linux-kernel, y.oudjana, Alec Su
This series adds the device tree for Xiaomi Mi 5s Plus (xiaomi-natrium)
smartphone which is based on Snapdragon 821 SoC.
Changes since v2:
- Rename the node "synaptics" to "touchscreen".
Changes since v1:
- Adjust the sequence of the patches in this series.
- Remove the unnecessary line and properties in the device tree.
- Rename the nodes contain underscores.
Alec Su (2):
dt-bindings: arm: qcom: Document xiaomi,natrium board
arm64: dts: qcom: msm8996-xiaomi-natrium: Add support for Xiaomi Mi 5s
Plus
.../devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/msm8996-xiaomi-natrium.dts | 416 ++++++++++++++++++
3 files changed, 418 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
--
2.35.3
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3 1/2] dt-bindings: arm: qcom: Document xiaomi,natrium board
2022-05-20 12:04 ` [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus Alec Su
@ 2022-05-20 12:04 ` Alec Su
2022-05-20 12:04 ` [PATCH v3 2/2] arm64: dts: qcom: msm8996-xiaomi-natrium: Add support for Xiaomi Mi 5s Plus Alec Su
2022-05-30 7:07 ` [PATCH v3 0/2] " Pavel Machek
2 siblings, 0 replies; 5+ messages in thread
From: Alec Su @ 2022-05-20 12:04 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt, krzysztof.kozlowski+dt, sboyd
Cc: linux-arm-msm, devicetree, linux-kernel, y.oudjana, Alec Su,
Krzysztof Kozlowski
Document Xiaomi Mi 5s Plus (xiaomi-natrium) smartphone which is based on
Snapdragon 821 SoC.
Signed-off-by: Alec Su <ae40515@yahoo.com.tw>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 5c06d1bfc046..7ee852079d13 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -190,6 +190,7 @@ properties:
- sony,kagura-row
- sony,keyaki-row
- xiaomi,gemini
+ - xiaomi,natrium
- xiaomi,scorpio
- const: qcom,msm8996
--
2.35.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v3 2/2] arm64: dts: qcom: msm8996-xiaomi-natrium: Add support for Xiaomi Mi 5s Plus
2022-05-20 12:04 ` [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus Alec Su
2022-05-20 12:04 ` [PATCH v3 1/2] dt-bindings: arm: qcom: Document xiaomi,natrium board Alec Su
@ 2022-05-20 12:04 ` Alec Su
2022-05-30 7:07 ` [PATCH v3 0/2] " Pavel Machek
2 siblings, 0 replies; 5+ messages in thread
From: Alec Su @ 2022-05-20 12:04 UTC (permalink / raw)
To: agross, bjorn.andersson, robh+dt, krzysztof.kozlowski+dt, sboyd
Cc: linux-arm-msm, devicetree, linux-kernel, y.oudjana, Alec Su
Add the device tree for Xiaomi Mi 5s Plus (natrium).
Signed-off-by: Alec Su <ae40515@yahoo.com.tw>
Reviewed-by: Yassine Oudjana <y.oudjana@protonmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/msm8996-xiaomi-natrium.dts | 416 ++++++++++++++++++
2 files changed, 417 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 2f8aec2cc6db..3ae7ecd369fb 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-dora.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-kagura.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-keyaki.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-xiaomi-gemini.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-xiaomi-natrium.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-xiaomi-scorpio.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8998-fxtec-pro1.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
new file mode 100644
index 000000000000..007788b7279f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Alec Su <ae40515@yahoo.com.tw>
+ */
+
+/dts-v1/;
+
+#include "msm8996-xiaomi-common.dtsi"
+#include "pmi8996.dtsi"
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+ model = "Xiaomi Mi 5s Plus";
+ compatible = "xiaomi,natrium", "qcom,msm8996";
+ chassis-type = "handset";
+ qcom,msm-id = <305 0x10000>;
+ qcom,board-id = <47 0>;
+};
+
+&adsp_pil {
+ firmware-name = "qcom/msm8996/natrium/adsp.mbn";
+};
+
+&blsp2_i2c6 {
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+ vdda-supply = <&vreg_l6a_1p8>;
+ vdd-supply = <&vdd_3v2_tp>;
+ reset-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&touchscreen_default>;
+ pinctrl-1 = <&touchscreen_sleep>;
+ };
+};
+
+&dsi0 {
+ status = "okay";
+
+ vdd-supply = <&vreg_l2a_1p25>;
+ vdda-supply = <&vreg_l19a_3p3>;
+ vddio-supply = <&vreg_l14a_1p8>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mdss_dsi_default &mdss_te_default>;
+ pinctrl-1 = <&mdss_dsi_sleep &mdss_te_sleep>;
+
+ panel: panel@0 {
+ compatible = "jdi,fhd-r63452";
+ reg = <0>;
+ reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+ backlight = <&pmi8994_wled>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in>;
+};
+
+&gpu {
+ zap-shader {
+ firmware-name = "qcom/msm8996/natrium/a530_zap.mbn";
+ };
+};
+
+&mss_pil {
+ firmware-name = "qcom/msm8996/natrium/mba.mbn",
+ "qcom/msm8996/natrium/modem.mbn";
+};
+
+&pmi8994_wled {
+ status = "okay";
+
+ qcom,num-strings = <2>;
+ qcom,enabled-strings = <0 1>;
+ qcom,switching-freq = <600>;
+};
+
+&q6asmdai {
+ dai@0 {
+ reg = <0>;
+ };
+
+ dai@1 {
+ reg = <1>;
+ };
+
+ dai@2 {
+ reg = <2>;
+ };
+};
+
+&slpi_pil {
+ firmware-name = "qcom/msm8996/natrium/slpi.mbn";
+};
+
+&sound {
+ compatible = "qcom,apq8096-sndcard";
+ model = "natrium";
+ audio-routing = "RX_BIAS", "MCLK";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_6_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 6>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 1>;
+ };
+ };
+};
+
+&venus {
+ firmware-name = "qcom/msm8996/natrium/venus.mbn";
+};
+
+&rpm_requests {
+ pm8994-regulators {
+ vreg_l3a_0p875: l3 {
+ regulator-name = "vreg_l3a_0p875";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1300000>;
+ };
+ vreg_l11a_1p1: l11 {
+ regulator-name = "vreg_l11a_1p1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+ vreg_l17a_2p8: l17 {
+ regulator-name = "vreg_l17a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ vreg_l18a_2p8: l18 {
+ regulator-name = "vreg_l18a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ vreg_l29a_2p8: l29 {
+ regulator-name = "vreg_l29a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+ };
+};
+
+&pm8994_gpios {
+ gpio-line-names =
+ "NC", /* GPIO_1 */
+ "VOL_UP_N", /* GPIO_2 */
+ "SPKR_ID", /* GPIO_3 */
+ "PWM_HAPTICS", /* GPIO_4 */
+ "INFARED_DRV", /* GPIO_5 */
+ "NC", /* GPIO_6 */
+ "KEYPAD_LED_EN_A", /* GPIO_7 */
+ "WL_EN", /* GPIO_8 */
+ "3P3_ENABLE", /* GPIO_9 */
+ "NC", /* GPIO_10 */
+ "NC", /* GPIO_11 */
+ "NC", /* GPIO_12 */
+ "NC", /* GPIO_13 */
+ "NC", /* GPIO_14 */
+ "DIVCLK1_CDC", /* GPIO_15 */
+ "DIVCLK2_HAPTICS", /* GPIO_16 */
+ "NC", /* GPIO_17 */
+ "32KHz_CLK_IN", /* GPIO_18 */
+ "BT_EN", /* GPIO_19 */
+ "PMIC_SLB", /* GPIO_20 */
+ "UIM_BATT_ALARM", /* GPIO_21 */
+ "NC"; /* GPIO_22 */
+};
+
+&pm8994_mpps {
+ gpio-line-names =
+ "NC", /* MPP_1 */
+ "CCI_TIMER1", /* MPP_2 */
+ "PMIC_SLB", /* MPP_3 */
+ "EXT_FET_WLED_PWR_EN_N",/* MPP_4 */
+ "NC", /* MPP_5 */
+ "NC", /* MPP_6 */
+ "NC", /* MPP_7 */
+ "NC"; /* MPP_8 */
+};
+
+&pmi8994_gpios {
+ gpio-line-names =
+ "NC", /* GPIO_1 */
+ "SPKR_PA_EN", /* GPIO_2 */
+ "NC", /* GPIO_3 */
+ "NC", /* GPIO_4 */
+ "NC", /* GPIO_5 */
+ "NC", /* GPIO_6 */
+ "NC", /* GPIO_7 */
+ "NC", /* GPIO_8 */
+ "NC", /* GPIO_9 */
+ "NC"; /* GPIO_10 */
+};
+
+&tlmm {
+ gpio-line-names =
+ "ESE_SPI_MOSI", /* GPIO_0 */
+ "ESE_SPI_MISO", /* GPIO_1 */
+ "NC", /* GPIO_2 */
+ "ESE_SPI_CLK", /* GPIO_3 */
+ "MSM_UART_TX", /* GPIO_4 */
+ "MSM_UART_RX", /* GPIO_5 */
+ "NFC_I2C_SDA", /* GPIO_6 */
+ "NFC_I2C_SCL", /* GPIO_7 */
+ "LCD0_RESET_N", /* GPIO_8 */
+ "NFC_IRQ", /* GPIO_9 */
+ "LCD_TE", /* GPIO_10 */
+ "LCD_ID_DET1", /* GPIO_11 */
+ "NFC_DISABLE", /* GPIO_12 */
+ "CAM_MCLK0", /* GPIO_13 */
+ "CAM_MCLK1", /* GPIO_14 */
+ "CAM_MCLK2", /* GPIO_15 */
+ "ESE_PWR_REQ", /* GPIO_16 */
+ "CCI_I2C_SDA0", /* GPIO_17 */
+ "CCI_I2C_SCL0", /* GPIO_18 */
+ "CCI_I2C_SDA1", /* GPIO_19 */
+ "CCI_I2C_SCL1", /* GPIO_20 */
+ "NFC_DWL_REQ", /* GPIO_21 */
+ "CCI_TIMER1", /* GPIO_22 */
+ "WEBCAM1_RESET_N", /* GPIO_23 */
+ "ESE_IRQ", /* GPIO_24 */
+ "NC", /* GPIO_25 */
+ "WEBCAM1_STANDBY", /* GPIO_26 */
+ "NC", /* GPIO_27 */
+ "NC", /* GPIO_28 */
+ "NC", /* GPIO_29 */
+ "CAM_VDD_1P2_EN_2", /* GPIO_30 */
+ "CAM_RESET_0", /* GPIO_31 */
+ "CAM_RESET_1", /* GPIO_32 */
+ "NC", /* GPIO_33 */
+ "NC", /* GPIO_34 */
+ "PCI_E0_RST_N", /* GPIO_35 */
+ "PCI_E0_CLKREQ_N", /* GPIO_36 */
+ "PCI_E0_WAKE", /* GPIO_37 */
+ "CHARGER_INT", /* GPIO_38 */
+ "CHARGER_RESET", /* GPIO_39 */
+ "NC", /* GPIO_40 */
+ "QCA_UART_TXD", /* GPIO_41 */
+ "QCA_UART_RXD", /* GPIO_42 */
+ "QCA_UART_CTS", /* GPIO_43 */
+ "QCA_UART_RTS", /* GPIO_44 */
+ "MAWC_UART_TX", /* GPIO_45 */
+ "MAWC_UART_RX", /* GPIO_46 */
+ "NC", /* GPIO_47 */
+ "NC", /* GPIO_48 */
+ "NC", /* GPIO_49 */
+ "FP_SPI_RST", /* GPIO_50 */
+ "TYPEC_I2C_SDA", /* GPIO_51 */
+ "TYPEC_I2C_SCL", /* GPIO_52 */
+ "CODEC_INT2_N", /* GPIO_53 */
+ "CODEC_INT1_N", /* GPIO_54 */
+ "APPS_I2C7_SDA", /* GPIO_55 */
+ "APPS_I2C7_SCL", /* GPIO_56 */
+ "FORCE_USB_BOOT", /* GPIO_57 */
+ "NC", /* GPIO_58 */
+ "NC", /* GPIO_59 */
+ "NC", /* GPIO_60 */
+ "NC", /* GPIO_61 */
+ "ESE_RSTN", /* GPIO_62 */
+ "TYPEC_INT", /* GPIO_63 */
+ "CODEC_RESET_N", /* GPIO_64 */
+ "PCM_CLK", /* GPIO_65 */
+ "PCM_SYNC", /* GPIO_66 */
+ "PCM_DIN", /* GPIO_67 */
+ "PCM_DOUT", /* GPIO_68 */
+ "CDC_44K1_CLK", /* GPIO_69 */
+ "SLIMBUS_CLK", /* GPIO_70 */
+ "SLIMBUS_DATA0", /* GPIO_71 */
+ "SLIMBUS_DATA1", /* GPIO_72 */
+ "LDO_5V_IN_EN", /* GPIO_73 */
+ "TYPEC_EN_N", /* GPIO_74 */
+ "NC", /* GPIO_75 */
+ "NC", /* GPIO_76 */
+ "NC", /* GPIO_77 */
+ "NC", /* GPIO_78 */
+ "NC", /* GPIO_79 */
+ "SENSOR_RESET_N", /* GPIO_80 */
+ "FP_SPI_MOSI", /* GPIO_81 */
+ "FP_SPI_MISO", /* GPIO_82 */
+ "FP_SPI_CS_N", /* GPIO_83 */
+ "FP_SPI_CLK", /* GPIO_84 */
+ "NC", /* GPIO_85 */
+ "CAM_VDD_1P2_EN", /* GPIO_86 */
+ "MSM_TS_I2C_SDA", /* GPIO_87 */
+ "MSM_TS_I2C_SCL", /* GPIO_88 */
+ "TS_RESOUT_N", /* GPIO_89 */
+ "ESE_SPI_CS_N", /* GPIO_90 */
+ "NC", /* GPIO_91 */
+ "CAM2_AVDD_EN", /* GPIO_92 */
+ "CAM2_VCM_EN", /* GPIO_93 */
+ "NC", /* GPIO_94 */
+ "NC", /* GPIO_95 */
+ "NC", /* GPIO_96 */
+ "GRFC_0", /* GPIO_97 */
+ "GRFC_1", /* GPIO_98 */
+ "NC", /* GPIO_99 */
+ "GRFC_3", /* GPIO_100 */
+ "GRFC_4", /* GPIO_101 */
+ "GRFC_5", /* GPIO_102 */
+ "NC", /* GPIO_103 */
+ "GRFC_7", /* GPIO_104 */
+ "UIM2_DATA", /* GPIO_105 */
+ "UIM2_CLK", /* GPIO_106 */
+ "UIM2_RESET", /* GPIO_107 */
+ "UIM2_PRESENT", /* GPIO_108 */
+ "UIM1_DATA", /* GPIO_109 */
+ "UIM1_CLK", /* GPIO_110 */
+ "UIM1_RESET", /* GPIO_111 */
+ "UIM1_PRESENT", /* GPIO_112 */
+ "UIM_BATT_ALARM", /* GPIO_113 */
+ "GRFC_8", /* GPIO_114 */
+ "GRFC_9", /* GPIO_115 */
+ "TX_GTR_THRES", /* GPIO_116 */
+ "ACCEL_INT", /* GPIO_117 */
+ "GYRO_INT", /* GPIO_118 */
+ "COMPASS_INT", /* GPIO_119 */
+ "PROXIMITY_INT_N", /* GPIO_120 */
+ "FP_IRQ", /* GPIO_121 */
+ "P_SENSE", /* GPIO_122 */
+ "HALL_INTR2", /* GPIO_123 */
+ "HALL_INTR1", /* GPIO_124 */
+ "TS_INT_N", /* GPIO_125 */
+ "NC", /* GPIO_126 */
+ "GRFC_11", /* GPIO_127 */
+ "NC", /* GPIO_128 */
+ "EXT_GPS_LNA_EN", /* GPIO_129 */
+ "NC", /* GPIO_130 */
+ "LCD_ID_DET2", /* GPIO_131 */
+ "LCD_TE2", /* GPIO_132 */
+ "GRFC_14", /* GPIO_133 */
+ "GSM_TX2_PHASE_D", /* GPIO_134 */
+ "NC", /* GPIO_135 */
+ "GRFC_15", /* GPIO_136 */
+ "RFFE3_DATA", /* GPIO_137 */
+ "RFFE3_CLK", /* GPIO_138 */
+ "NC", /* GPIO_139 */
+ "NC", /* GPIO_140 */
+ "RFFE5_DATA", /* GPIO_141 */
+ "RFFE5_CLK", /* GPIO_142 */
+ "NC", /* GPIO_143 */
+ "COEX_UART_TX", /* GPIO_144 */
+ "COEX_UART_RX", /* GPIO_145 */
+ "RFFE2_DATA", /* GPIO_146 */
+ "RFFE2_CLK", /* GPIO_147 */
+ "RFFE1_DATA", /* GPIO_148 */
+ "RFFE1_CLK"; /* GPIO_149 */
+
+ touchscreen_default: touchscreen-default {
+ pins = "gpio89", "gpio125";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ touchscreen_sleep: touchscreen-sleep {
+ pins = "gpio89", "gpio125";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
--
2.35.3
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus
2022-05-20 12:04 ` [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus Alec Su
2022-05-20 12:04 ` [PATCH v3 1/2] dt-bindings: arm: qcom: Document xiaomi,natrium board Alec Su
2022-05-20 12:04 ` [PATCH v3 2/2] arm64: dts: qcom: msm8996-xiaomi-natrium: Add support for Xiaomi Mi 5s Plus Alec Su
@ 2022-05-30 7:07 ` Pavel Machek
2022-05-30 7:35 ` Krzysztof Kozlowski
2 siblings, 1 reply; 5+ messages in thread
From: Pavel Machek @ 2022-05-30 7:07 UTC (permalink / raw)
To: Alec Su
Cc: agross, bjorn.andersson, robh+dt, krzysztof.kozlowski+dt, sboyd,
linux-arm-msm, devicetree, linux-kernel, y.oudjana
Hi!
> This series adds the device tree for Xiaomi Mi 5s Plus (xiaomi-natrium)
> smartphone which is based on Snapdragon 821 SoC.
Please cc phone-devel@ mailing list with phone-related patches.
Best regards,
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus
2022-05-30 7:07 ` [PATCH v3 0/2] " Pavel Machek
@ 2022-05-30 7:35 ` Krzysztof Kozlowski
0 siblings, 0 replies; 5+ messages in thread
From: Krzysztof Kozlowski @ 2022-05-30 7:35 UTC (permalink / raw)
To: Pavel Machek, Alec Su
Cc: agross, bjorn.andersson, robh+dt, krzysztof.kozlowski+dt, sboyd,
linux-arm-msm, devicetree, linux-kernel, y.oudjana
On 30/05/2022 09:07, Pavel Machek wrote:
> Hi!
>
>> This series adds the device tree for Xiaomi Mi 5s Plus (xiaomi-natrium)
>> smartphone which is based on Snapdragon 821 SoC.
>
> Please cc phone-devel@ mailing list with phone-related patches.
I think you need to come up with some smart content-pattern for
get_maintainers, because there is little chance I will remember to
manually Cc some different mailing lists depending on type of some
device or some other factor. I remember just to cc soc folks on certain
patches and that's it. Nothing else fits my memory. :) To avoid the
problem of poor human memory, we have a tool - scripts/get_maintainer.pl
- and contributors are encouraged to use that one. If you want to be
cc-ed, please either work on proper maintainers entry or set up some
custom lei filters.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-05-30 7:35 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <20220520120449.12996-1-ae40515.ref@yahoo.com.tw>
2022-05-20 12:04 ` [PATCH v3 0/2] Add support for Xiaomi Mi 5s Plus Alec Su
2022-05-20 12:04 ` [PATCH v3 1/2] dt-bindings: arm: qcom: Document xiaomi,natrium board Alec Su
2022-05-20 12:04 ` [PATCH v3 2/2] arm64: dts: qcom: msm8996-xiaomi-natrium: Add support for Xiaomi Mi 5s Plus Alec Su
2022-05-30 7:07 ` [PATCH v3 0/2] " Pavel Machek
2022-05-30 7:35 ` Krzysztof Kozlowski
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.