* [PATCH v8 0/8] ARM: Add Rockchip RV1126 support
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
This patch series combined the next level dts patches for
Rockchip RV1126 support.
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- new dt-bindings patches
- collect Rob Ack
Any inputs?
Jagan.
Jagan Teki (8):
dt-bindings: arm: rockchip: Add pmu compatible for rv1126
dt-bindings: timer: rk-timer: Add rktimer for rv1126
ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
ARM: dts: rockchip: Add Rockchip RV1126 SoC
dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
.../devicetree/bindings/arm/rockchip.yaml | 6 +
.../devicetree/bindings/arm/rockchip/pmu.yaml | 2 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 2 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 ++++++++++++++
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 +++++++++
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++
10 files changed, 1038 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 37+ messages in thread
* [PATCH v8 0/8] ARM: Add Rockchip RV1126 support
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
This patch series combined the next level dts patches for
Rockchip RV1126 support.
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- new dt-bindings patches
- collect Rob Ack
Any inputs?
Jagan.
Jagan Teki (8):
dt-bindings: arm: rockchip: Add pmu compatible for rv1126
dt-bindings: timer: rk-timer: Add rktimer for rv1126
ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
ARM: dts: rockchip: Add Rockchip RV1126 SoC
dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
.../devicetree/bindings/arm/rockchip.yaml | 6 +
.../devicetree/bindings/arm/rockchip/pmu.yaml | 2 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 2 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 ++++++++++++++
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 +++++++++
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++
10 files changed, 1038 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 37+ messages in thread
* [PATCH v8 0/8] ARM: Add Rockchip RV1126 support
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
This patch series combined the next level dts patches for
Rockchip RV1126 support.
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- new dt-bindings patches
- collect Rob Ack
Any inputs?
Jagan.
Jagan Teki (8):
dt-bindings: arm: rockchip: Add pmu compatible for rv1126
dt-bindings: timer: rk-timer: Add rktimer for rv1126
ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
ARM: dts: rockchip: Add Rockchip RV1126 SoC
dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
.../devicetree/bindings/arm/rockchip.yaml | 6 +
.../devicetree/bindings/arm/rockchip/pmu.yaml | 2 +
.../bindings/timer/rockchip,rk-timer.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 2 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 ++++++++++++++
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 +++++++++
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++
10 files changed, 1038 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 37+ messages in thread
* [PATCH v8 1/8] dt-bindings: arm: rockchip: Add pmu compatible for rv1126
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Krzysztof Kozlowski
Add PMU compatible string for rockchip rv1126.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- add Krzysztof ack
Changes for v7:
- new patch
Documentation/devicetree/bindings/arm/rockchip/pmu.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
index 8c73bc7f4009..b79c81cd9f0e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
@@ -27,6 +27,7 @@ select:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
required:
- compatible
@@ -43,6 +44,7 @@ properties:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
- const: syscon
- const: simple-mfd
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 1/8] dt-bindings: arm: rockchip: Add pmu compatible for rv1126
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Krzysztof Kozlowski
Add PMU compatible string for rockchip rv1126.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- add Krzysztof ack
Changes for v7:
- new patch
Documentation/devicetree/bindings/arm/rockchip/pmu.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
index 8c73bc7f4009..b79c81cd9f0e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
@@ -27,6 +27,7 @@ select:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
required:
- compatible
@@ -43,6 +44,7 @@ properties:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
- const: syscon
- const: simple-mfd
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 1/8] dt-bindings: arm: rockchip: Add pmu compatible for rv1126
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Krzysztof Kozlowski
Add PMU compatible string for rockchip rv1126.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- add Krzysztof ack
Changes for v7:
- new patch
Documentation/devicetree/bindings/arm/rockchip/pmu.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
index 8c73bc7f4009..b79c81cd9f0e 100644
--- a/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip/pmu.yaml
@@ -27,6 +27,7 @@ select:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
required:
- compatible
@@ -43,6 +44,7 @@ properties:
- rockchip,rk3399-pmu
- rockchip,rk3568-pmu
- rockchip,rk3588-pmu
+ - rockchip,rv1126-pmu
- const: syscon
- const: simple-mfd
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add rockchip timer compatible string for rockchip rv1126.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- drop cc list
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62fe9..a6221222e948 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -17,6 +17,7 @@ properties:
- items:
- enum:
- rockchip,rv1108-timer
+ - rockchip,rv1126-timer
- rockchip,rk3036-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add rockchip timer compatible string for rockchip rv1126.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- drop cc list
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62fe9..a6221222e948 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -17,6 +17,7 @@ properties:
- items:
- enum:
- rockchip,rv1108-timer
+ - rockchip,rv1126-timer
- rockchip,rk3036-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add rockchip timer compatible string for rockchip rv1126.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- drop cc list
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index dc3bc1e62fe9..a6221222e948 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -17,6 +17,7 @@ properties:
- items:
- enum:
- rockchip,rv1108-timer
+ - rockchip,rv1126-timer
- rockchip,rk3036-timer
- rockchip,rk3188-timer
- rockchip,rk3228-timer
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 3/8] ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add pinctrl definitions for Rockchip RV1126.
From RK3568 on-wards pinctrl configurations are maintained
in common conf file rockchip-pinconf.dtsi and it is available
in arm64 path (arch/arm64/boot/dts/rockchip/rockchip-pinconf.dtsi).
So, include the same conf file to RV1126 pinctrl from arm64 path.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- remove Edegble in license text
Changes for v6:
- updated commit message
Changes for v5:
- none
Changes for v4:
- update i2c pins
- rebase on -next
Changes for v3:
- none
Changes for v2:
- spilt pinctrl as separate patch
MAINTAINERS | 2 +-
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 ++++++++++++++++++++++++++
2 files changed, 212 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
diff --git a/MAINTAINERS b/MAINTAINERS
index 5f66378dcfb0..4fd0fa773209 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2750,7 +2750,7 @@ F: Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
F: Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
F: Documentation/devicetree/bindings/spi/spi-rockchip.yaml
F: arch/arm/boot/dts/rk3*
-F: arch/arm/boot/dts/rv1108*
+F: arch/arm/boot/dts/rv11*
F: arch/arm/mach-rockchip/
F: drivers/*/*/*rockchip*
F: drivers/*/*rockchip*
diff --git a/arch/arm/boot/dts/rv1126-pinctrl.dtsi b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
new file mode 100644
index 000000000000..4bc419cc1210
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <arm64/rockchip/rockchip-pinconf.dtsi>
+
+/*
+ * This file is auto generated by pin2dts tool, please keep these code
+ * by adding changes at end of this file.
+ */
+&pinctrl {
+ emmc {
+ /omit-if-no-ref/
+ emmc_rstnout: emmc-rstnout {
+ rockchip,pins =
+ /* emmc_rstn */
+ <1 RK_PA3 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins =
+ /* emmc_d0 */
+ <0 RK_PC4 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d1 */
+ <0 RK_PC5 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d2 */
+ <0 RK_PC6 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d3 */
+ <0 RK_PC7 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d4 */
+ <0 RK_PD0 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d5 */
+ <0 RK_PD1 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d6 */
+ <0 RK_PD2 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d7 */
+ <0 RK_PD3 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_clk: emmc-clk {
+ rockchip,pins =
+ /* emmc_clko */
+ <0 RK_PD7 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_cmd: emmc-cmd {
+ rockchip,pins =
+ /* emmc_cmd */
+ <0 RK_PD5 2 &pcfg_pull_up_drv_level_2>;
+ };
+ };
+ i2c0 {
+ /omit-if-no-ref/
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins =
+ /* i2c0_scl */
+ <0 RK_PB4 1 &pcfg_pull_none_drv_level_0_smt>,
+ /* i2c0_sda */
+ <0 RK_PB5 1 &pcfg_pull_none_drv_level_0_smt>;
+ };
+ };
+ sdmmc0 {
+ /omit-if-no-ref/
+ sdmmc0_bus4: sdmmc0-bus4 {
+ rockchip,pins =
+ /* sdmmc0_d0 */
+ <1 RK_PA4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d1 */
+ <1 RK_PA5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d2 */
+ <1 RK_PA6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d3 */
+ <1 RK_PA7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_clk: sdmmc0-clk {
+ rockchip,pins =
+ /* sdmmc0_clk */
+ <1 RK_PB0 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_cmd: sdmmc0-cmd {
+ rockchip,pins =
+ /* sdmmc0_cmd */
+ <1 RK_PB1 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_det: sdmmc0-det {
+ rockchip,pins =
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_pwr: sdmmc0-pwr {
+ rockchip,pins =
+ <0 RK_PC0 1 &pcfg_pull_none>;
+ };
+ };
+ sdmmc1 {
+ /omit-if-no-ref/
+ sdmmc1_bus4: sdmmc1-bus4 {
+ rockchip,pins =
+ /* sdmmc1_d0 */
+ <1 RK_PB4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d1 */
+ <1 RK_PB5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d2 */
+ <1 RK_PB6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d3 */
+ <1 RK_PB7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_clk: sdmmc1-clk {
+ rockchip,pins =
+ /* sdmmc1_clk */
+ <1 RK_PB2 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_cmd: sdmmc1-cmd {
+ rockchip,pins =
+ /* sdmmc1_cmd */
+ <1 RK_PB3 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_det: sdmmc1-det {
+ rockchip,pins =
+ <1 RK_PD0 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_pwr: sdmmc1-pwr {
+ rockchip,pins =
+ <1 RK_PD1 2 &pcfg_pull_none>;
+ };
+ };
+ uart0 {
+ /omit-if-no-ref/
+ uart0_xfer: uart0-xfer {
+ rockchip,pins =
+ /* uart0_rx */
+ <1 RK_PC2 1 &pcfg_pull_up>,
+ /* uart0_tx */
+ <1 RK_PC3 1 &pcfg_pull_up>;
+ };
+ /omit-if-no-ref/
+ uart0_ctsn: uart0-ctsn {
+ rockchip,pins =
+ <1 RK_PC1 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn: uart0-rtsn {
+ rockchip,pins =
+ <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn_gpio: uart0-rts-pin {
+ rockchip,pins =
+ <1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+ uart1 {
+ /omit-if-no-ref/
+ uart1m0_xfer: uart1m0-xfer {
+ rockchip,pins =
+ /* uart1_rx_m0 */
+ <0 RK_PB7 2 &pcfg_pull_up>,
+ /* uart1_tx_m0 */
+ <0 RK_PB6 2 &pcfg_pull_up>;
+ };
+ };
+ uart2 {
+ /omit-if-no-ref/
+ uart2m1_xfer: uart2m1-xfer {
+ rockchip,pins =
+ /* uart2_rx_m1 */
+ <3 RK_PA3 1 &pcfg_pull_up>,
+ /* uart2_tx_m1 */
+ <3 RK_PA2 1 &pcfg_pull_up>;
+ };
+ };
+ uart3 {
+ /omit-if-no-ref/
+ uart3m0_xfer: uart3m0-xfer {
+ rockchip,pins =
+ /* uart3_rx_m0 */
+ <3 RK_PC7 4 &pcfg_pull_up>,
+ /* uart3_tx_m0 */
+ <3 RK_PC6 4 &pcfg_pull_up>;
+ };
+ };
+ uart4 {
+ /omit-if-no-ref/
+ uart4m0_xfer: uart4m0-xfer {
+ rockchip,pins =
+ /* uart4_rx_m0 */
+ <3 RK_PA5 4 &pcfg_pull_up>,
+ /* uart4_tx_m0 */
+ <3 RK_PA4 4 &pcfg_pull_up>;
+ };
+ };
+ uart5 {
+ /omit-if-no-ref/
+ uart5m0_xfer: uart5m0-xfer {
+ rockchip,pins =
+ /* uart5_rx_m0 */
+ <3 RK_PA7 4 &pcfg_pull_up>,
+ /* uart5_tx_m0 */
+ <3 RK_PA6 4 &pcfg_pull_up>;
+ };
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 3/8] ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add pinctrl definitions for Rockchip RV1126.
From RK3568 on-wards pinctrl configurations are maintained
in common conf file rockchip-pinconf.dtsi and it is available
in arm64 path (arch/arm64/boot/dts/rockchip/rockchip-pinconf.dtsi).
So, include the same conf file to RV1126 pinctrl from arm64 path.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- remove Edegble in license text
Changes for v6:
- updated commit message
Changes for v5:
- none
Changes for v4:
- update i2c pins
- rebase on -next
Changes for v3:
- none
Changes for v2:
- spilt pinctrl as separate patch
MAINTAINERS | 2 +-
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 ++++++++++++++++++++++++++
2 files changed, 212 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
diff --git a/MAINTAINERS b/MAINTAINERS
index 5f66378dcfb0..4fd0fa773209 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2750,7 +2750,7 @@ F: Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
F: Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
F: Documentation/devicetree/bindings/spi/spi-rockchip.yaml
F: arch/arm/boot/dts/rk3*
-F: arch/arm/boot/dts/rv1108*
+F: arch/arm/boot/dts/rv11*
F: arch/arm/mach-rockchip/
F: drivers/*/*/*rockchip*
F: drivers/*/*rockchip*
diff --git a/arch/arm/boot/dts/rv1126-pinctrl.dtsi b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
new file mode 100644
index 000000000000..4bc419cc1210
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <arm64/rockchip/rockchip-pinconf.dtsi>
+
+/*
+ * This file is auto generated by pin2dts tool, please keep these code
+ * by adding changes at end of this file.
+ */
+&pinctrl {
+ emmc {
+ /omit-if-no-ref/
+ emmc_rstnout: emmc-rstnout {
+ rockchip,pins =
+ /* emmc_rstn */
+ <1 RK_PA3 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins =
+ /* emmc_d0 */
+ <0 RK_PC4 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d1 */
+ <0 RK_PC5 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d2 */
+ <0 RK_PC6 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d3 */
+ <0 RK_PC7 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d4 */
+ <0 RK_PD0 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d5 */
+ <0 RK_PD1 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d6 */
+ <0 RK_PD2 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d7 */
+ <0 RK_PD3 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_clk: emmc-clk {
+ rockchip,pins =
+ /* emmc_clko */
+ <0 RK_PD7 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_cmd: emmc-cmd {
+ rockchip,pins =
+ /* emmc_cmd */
+ <0 RK_PD5 2 &pcfg_pull_up_drv_level_2>;
+ };
+ };
+ i2c0 {
+ /omit-if-no-ref/
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins =
+ /* i2c0_scl */
+ <0 RK_PB4 1 &pcfg_pull_none_drv_level_0_smt>,
+ /* i2c0_sda */
+ <0 RK_PB5 1 &pcfg_pull_none_drv_level_0_smt>;
+ };
+ };
+ sdmmc0 {
+ /omit-if-no-ref/
+ sdmmc0_bus4: sdmmc0-bus4 {
+ rockchip,pins =
+ /* sdmmc0_d0 */
+ <1 RK_PA4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d1 */
+ <1 RK_PA5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d2 */
+ <1 RK_PA6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d3 */
+ <1 RK_PA7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_clk: sdmmc0-clk {
+ rockchip,pins =
+ /* sdmmc0_clk */
+ <1 RK_PB0 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_cmd: sdmmc0-cmd {
+ rockchip,pins =
+ /* sdmmc0_cmd */
+ <1 RK_PB1 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_det: sdmmc0-det {
+ rockchip,pins =
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_pwr: sdmmc0-pwr {
+ rockchip,pins =
+ <0 RK_PC0 1 &pcfg_pull_none>;
+ };
+ };
+ sdmmc1 {
+ /omit-if-no-ref/
+ sdmmc1_bus4: sdmmc1-bus4 {
+ rockchip,pins =
+ /* sdmmc1_d0 */
+ <1 RK_PB4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d1 */
+ <1 RK_PB5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d2 */
+ <1 RK_PB6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d3 */
+ <1 RK_PB7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_clk: sdmmc1-clk {
+ rockchip,pins =
+ /* sdmmc1_clk */
+ <1 RK_PB2 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_cmd: sdmmc1-cmd {
+ rockchip,pins =
+ /* sdmmc1_cmd */
+ <1 RK_PB3 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_det: sdmmc1-det {
+ rockchip,pins =
+ <1 RK_PD0 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_pwr: sdmmc1-pwr {
+ rockchip,pins =
+ <1 RK_PD1 2 &pcfg_pull_none>;
+ };
+ };
+ uart0 {
+ /omit-if-no-ref/
+ uart0_xfer: uart0-xfer {
+ rockchip,pins =
+ /* uart0_rx */
+ <1 RK_PC2 1 &pcfg_pull_up>,
+ /* uart0_tx */
+ <1 RK_PC3 1 &pcfg_pull_up>;
+ };
+ /omit-if-no-ref/
+ uart0_ctsn: uart0-ctsn {
+ rockchip,pins =
+ <1 RK_PC1 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn: uart0-rtsn {
+ rockchip,pins =
+ <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn_gpio: uart0-rts-pin {
+ rockchip,pins =
+ <1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+ uart1 {
+ /omit-if-no-ref/
+ uart1m0_xfer: uart1m0-xfer {
+ rockchip,pins =
+ /* uart1_rx_m0 */
+ <0 RK_PB7 2 &pcfg_pull_up>,
+ /* uart1_tx_m0 */
+ <0 RK_PB6 2 &pcfg_pull_up>;
+ };
+ };
+ uart2 {
+ /omit-if-no-ref/
+ uart2m1_xfer: uart2m1-xfer {
+ rockchip,pins =
+ /* uart2_rx_m1 */
+ <3 RK_PA3 1 &pcfg_pull_up>,
+ /* uart2_tx_m1 */
+ <3 RK_PA2 1 &pcfg_pull_up>;
+ };
+ };
+ uart3 {
+ /omit-if-no-ref/
+ uart3m0_xfer: uart3m0-xfer {
+ rockchip,pins =
+ /* uart3_rx_m0 */
+ <3 RK_PC7 4 &pcfg_pull_up>,
+ /* uart3_tx_m0 */
+ <3 RK_PC6 4 &pcfg_pull_up>;
+ };
+ };
+ uart4 {
+ /omit-if-no-ref/
+ uart4m0_xfer: uart4m0-xfer {
+ rockchip,pins =
+ /* uart4_rx_m0 */
+ <3 RK_PA5 4 &pcfg_pull_up>,
+ /* uart4_tx_m0 */
+ <3 RK_PA4 4 &pcfg_pull_up>;
+ };
+ };
+ uart5 {
+ /omit-if-no-ref/
+ uart5m0_xfer: uart5m0-xfer {
+ rockchip,pins =
+ /* uart5_rx_m0 */
+ <3 RK_PA7 4 &pcfg_pull_up>,
+ /* uart5_tx_m0 */
+ <3 RK_PA6 4 &pcfg_pull_up>;
+ };
+ };
+};
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 3/8] ARM: dts: rockchip: Add Rockchip RV1126 pinctrl
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Add pinctrl definitions for Rockchip RV1126.
From RK3568 on-wards pinctrl configurations are maintained
in common conf file rockchip-pinconf.dtsi and it is available
in arm64 path (arch/arm64/boot/dts/rockchip/rockchip-pinconf.dtsi).
So, include the same conf file to RV1126 pinctrl from arm64 path.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- remove Edegble in license text
Changes for v6:
- updated commit message
Changes for v5:
- none
Changes for v4:
- update i2c pins
- rebase on -next
Changes for v3:
- none
Changes for v2:
- spilt pinctrl as separate patch
MAINTAINERS | 2 +-
arch/arm/boot/dts/rv1126-pinctrl.dtsi | 211 ++++++++++++++++++++++++++
2 files changed, 212 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/rv1126-pinctrl.dtsi
diff --git a/MAINTAINERS b/MAINTAINERS
index 5f66378dcfb0..4fd0fa773209 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2750,7 +2750,7 @@ F: Documentation/devicetree/bindings/i2c/i2c-rk3x.yaml
F: Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
F: Documentation/devicetree/bindings/spi/spi-rockchip.yaml
F: arch/arm/boot/dts/rk3*
-F: arch/arm/boot/dts/rv1108*
+F: arch/arm/boot/dts/rv11*
F: arch/arm/mach-rockchip/
F: drivers/*/*/*rockchip*
F: drivers/*/*rockchip*
diff --git a/arch/arm/boot/dts/rv1126-pinctrl.dtsi b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
new file mode 100644
index 000000000000..4bc419cc1210
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-pinctrl.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
+ */
+
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <arm64/rockchip/rockchip-pinconf.dtsi>
+
+/*
+ * This file is auto generated by pin2dts tool, please keep these code
+ * by adding changes at end of this file.
+ */
+&pinctrl {
+ emmc {
+ /omit-if-no-ref/
+ emmc_rstnout: emmc-rstnout {
+ rockchip,pins =
+ /* emmc_rstn */
+ <1 RK_PA3 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins =
+ /* emmc_d0 */
+ <0 RK_PC4 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d1 */
+ <0 RK_PC5 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d2 */
+ <0 RK_PC6 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d3 */
+ <0 RK_PC7 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d4 */
+ <0 RK_PD0 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d5 */
+ <0 RK_PD1 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d6 */
+ <0 RK_PD2 2 &pcfg_pull_up_drv_level_2>,
+ /* emmc_d7 */
+ <0 RK_PD3 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_clk: emmc-clk {
+ rockchip,pins =
+ /* emmc_clko */
+ <0 RK_PD7 2 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ emmc_cmd: emmc-cmd {
+ rockchip,pins =
+ /* emmc_cmd */
+ <0 RK_PD5 2 &pcfg_pull_up_drv_level_2>;
+ };
+ };
+ i2c0 {
+ /omit-if-no-ref/
+ i2c0_xfer: i2c0-xfer {
+ rockchip,pins =
+ /* i2c0_scl */
+ <0 RK_PB4 1 &pcfg_pull_none_drv_level_0_smt>,
+ /* i2c0_sda */
+ <0 RK_PB5 1 &pcfg_pull_none_drv_level_0_smt>;
+ };
+ };
+ sdmmc0 {
+ /omit-if-no-ref/
+ sdmmc0_bus4: sdmmc0-bus4 {
+ rockchip,pins =
+ /* sdmmc0_d0 */
+ <1 RK_PA4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d1 */
+ <1 RK_PA5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d2 */
+ <1 RK_PA6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc0_d3 */
+ <1 RK_PA7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_clk: sdmmc0-clk {
+ rockchip,pins =
+ /* sdmmc0_clk */
+ <1 RK_PB0 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_cmd: sdmmc0-cmd {
+ rockchip,pins =
+ /* sdmmc0_cmd */
+ <1 RK_PB1 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_det: sdmmc0-det {
+ rockchip,pins =
+ <0 RK_PA3 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc0_pwr: sdmmc0-pwr {
+ rockchip,pins =
+ <0 RK_PC0 1 &pcfg_pull_none>;
+ };
+ };
+ sdmmc1 {
+ /omit-if-no-ref/
+ sdmmc1_bus4: sdmmc1-bus4 {
+ rockchip,pins =
+ /* sdmmc1_d0 */
+ <1 RK_PB4 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d1 */
+ <1 RK_PB5 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d2 */
+ <1 RK_PB6 1 &pcfg_pull_up_drv_level_2>,
+ /* sdmmc1_d3 */
+ <1 RK_PB7 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_clk: sdmmc1-clk {
+ rockchip,pins =
+ /* sdmmc1_clk */
+ <1 RK_PB2 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_cmd: sdmmc1-cmd {
+ rockchip,pins =
+ /* sdmmc1_cmd */
+ <1 RK_PB3 1 &pcfg_pull_up_drv_level_2>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_det: sdmmc1-det {
+ rockchip,pins =
+ <1 RK_PD0 2 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ sdmmc1_pwr: sdmmc1-pwr {
+ rockchip,pins =
+ <1 RK_PD1 2 &pcfg_pull_none>;
+ };
+ };
+ uart0 {
+ /omit-if-no-ref/
+ uart0_xfer: uart0-xfer {
+ rockchip,pins =
+ /* uart0_rx */
+ <1 RK_PC2 1 &pcfg_pull_up>,
+ /* uart0_tx */
+ <1 RK_PC3 1 &pcfg_pull_up>;
+ };
+ /omit-if-no-ref/
+ uart0_ctsn: uart0-ctsn {
+ rockchip,pins =
+ <1 RK_PC1 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn: uart0-rtsn {
+ rockchip,pins =
+ <1 RK_PC0 1 &pcfg_pull_none>;
+ };
+ /omit-if-no-ref/
+ uart0_rtsn_gpio: uart0-rts-pin {
+ rockchip,pins =
+ <1 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+ uart1 {
+ /omit-if-no-ref/
+ uart1m0_xfer: uart1m0-xfer {
+ rockchip,pins =
+ /* uart1_rx_m0 */
+ <0 RK_PB7 2 &pcfg_pull_up>,
+ /* uart1_tx_m0 */
+ <0 RK_PB6 2 &pcfg_pull_up>;
+ };
+ };
+ uart2 {
+ /omit-if-no-ref/
+ uart2m1_xfer: uart2m1-xfer {
+ rockchip,pins =
+ /* uart2_rx_m1 */
+ <3 RK_PA3 1 &pcfg_pull_up>,
+ /* uart2_tx_m1 */
+ <3 RK_PA2 1 &pcfg_pull_up>;
+ };
+ };
+ uart3 {
+ /omit-if-no-ref/
+ uart3m0_xfer: uart3m0-xfer {
+ rockchip,pins =
+ /* uart3_rx_m0 */
+ <3 RK_PC7 4 &pcfg_pull_up>,
+ /* uart3_tx_m0 */
+ <3 RK_PC6 4 &pcfg_pull_up>;
+ };
+ };
+ uart4 {
+ /omit-if-no-ref/
+ uart4m0_xfer: uart4m0-xfer {
+ rockchip,pins =
+ /* uart4_rx_m0 */
+ <3 RK_PA5 4 &pcfg_pull_up>,
+ /* uart4_tx_m0 */
+ <3 RK_PA4 4 &pcfg_pull_up>;
+ };
+ };
+ uart5 {
+ /omit-if-no-ref/
+ uart5m0_xfer: uart5m0-xfer {
+ rockchip,pins =
+ /* uart5_rx_m0 */
+ <3 RK_PA7 4 &pcfg_pull_up>,
+ /* uart5_tx_m0 */
+ <3 RK_PA6 4 &pcfg_pull_up>;
+ };
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 4/8] ARM: dts: rockchip: Add Rockchip RV1126 SoC
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Jon Lin, Sugar Zhang
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- rearrange nodes
- remove Edegble in license text
Changes for v6:
- add psci node
Changes for v5:
- none
Changes for v4:
- update i2c0
- rebase on -next
Changes for v3:
- update cru and power file names
Changes for v2:
- split pinctrl in separate patch
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++++++++++++++++++
1 file changed, 438 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
diff --git a/arch/arm/boot/dts/rv1126.dtsi b/arch/arm/boot/dts/rv1126.dtsi
new file mode 100644
index 000000000000..1cb43147e90b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126.dtsi
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+#include <dt-bindings/clock/rockchip,rv1126-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rockchip,rv1126-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "rockchip,rv1126";
+
+ interrupt-parent = <&gic>;
+
+ aliases {
+ i2c0 = &i2c0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ grf: syscon@fe000000 {
+ compatible = "rockchip,rv1126-grf", "syscon", "simple-mfd";
+ reg = <0xfe000000 0x20000>;
+ };
+
+ pmugrf: syscon@fe020000 {
+ compatible = "rockchip,rv1126-pmugrf", "syscon", "simple-mfd";
+ reg = <0xfe020000 0x1000>;
+
+ pmu_io_domains: io-domains {
+ compatible = "rockchip,rv1126-pmu-io-voltage-domain";
+ status = "disabled";
+ };
+ };
+
+ qos_emmc: qos@fe860000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860000 0x20>;
+ };
+
+ qos_nandc: qos@fe860080 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860080 0x20>;
+ };
+
+ qos_sfc: qos@fe860200 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860200 0x20>;
+ };
+
+ qos_sdio: qos@fe86c000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe86c000 0x20>;
+ };
+
+ gic: interrupt-controller@feff0000 {
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+
+ reg = <0xfeff1000 0x1000>,
+ <0xfeff2000 0x2000>,
+ <0xfeff4000 0x2000>,
+ <0xfeff6000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ pmu: power-management@ff3e0000 {
+ compatible = "rockchip,rv1126-pmu", "syscon", "simple-mfd";
+ reg = <0xff3e0000 0x1000>;
+
+ power: power-controller {
+ compatible = "rockchip,rv1126-power-controller";
+ #power-domain-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-domain@RV1126_PD_NVM {
+ reg = <RV1126_PD_NVM>;
+ clocks = <&cru HCLK_EMMC>,
+ <&cru CLK_EMMC>,
+ <&cru HCLK_NANDC>,
+ <&cru CLK_NANDC>,
+ <&cru HCLK_SFC>,
+ <&cru HCLK_SFCXIP>,
+ <&cru SCLK_SFC>;
+ pm_qos = <&qos_emmc>,
+ <&qos_nandc>,
+ <&qos_sfc>;
+ #power-domain-cells = <0>;
+ };
+
+ power-domain@RV1126_PD_SDIO {
+ reg = <RV1126_PD_SDIO>;
+ clocks = <&cru HCLK_SDIO>,
+ <&cru CLK_SDIO>;
+ pm_qos = <&qos_sdio>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+
+ i2c0: i2c@ff3f0000 {
+ compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c";
+ reg = <0xff3f0000 0x1000>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ rockchip,grf = <&pmugrf>;
+ clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
+ clock-names = "i2c", "pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart1: serial@ff410000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff410000 0x100>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&pmucru SCLK_UART1>, <&pmucru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 7>, <&dmac 6>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ pmucru: clock-controller@ff480000 {
+ compatible = "rockchip,rv1126-pmucru";
+ reg = <0xff480000 0x1000>;
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ cru: clock-controller@ff490000 {
+ compatible = "rockchip,rv1126-cru";
+ reg = <0xff490000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ dmac: dma-controller@ff4e0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0xff4e0000 0x4000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ arm,pl330-periph-burst;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ };
+
+ uart0: serial@ff560000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff560000 0x100>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 5>, <&dmac 4>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart2: serial@ff570000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff570000 0x100>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 9>, <&dmac 8>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m1_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart3: serial@ff580000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff580000 0x100>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 11>, <&dmac 10>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart4: serial@ff590000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff590000 0x100>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 13>, <&dmac 12>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart5: serial@ff5a0000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff5a0000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 15>, <&dmac 14>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ saradc: adc@ff5e0000 {
+ compatible = "rockchip,rv1126-saradc", "rockchip,rk3399-saradc";
+ reg = <0xff5e0000 0x100>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ #io-channel-cells = <1>;
+ clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC_P>;
+ reset-names = "saradc-apb";
+ status = "disabled";
+ };
+
+ timer0: timer@ff660000 {
+ compatible = "rockchip,rv1126-timer", "rockchip,rk3288-timer";
+ reg = <0xff660000 0x20>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&cru CLK_TIMER0>;
+ clock-names = "pclk", "timer";
+ };
+
+ emmc: mmc@ffc50000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc50000 0x4000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru CLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_NVM>;
+ status = "disabled";
+ };
+
+ sdmmc: mmc@ffc60000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc60000 0x4000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru CLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ status = "disabled";
+ };
+
+ sdio: mmc@ffc70000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc70000 0x4000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru CLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_SDIO>;
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rv1126-pinctrl";
+ rockchip,grf = <&grf>;
+ rockchip,pmu = <&pmugrf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@ff460000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff460000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@ff620000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff620000 0x100>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@ff630000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff630000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@ff640000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff640000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@ff650000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff650000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+#include "rv1126-pinctrl.dtsi"
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 4/8] ARM: dts: rockchip: Add Rockchip RV1126 SoC
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Jon Lin, Sugar Zhang
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- rearrange nodes
- remove Edegble in license text
Changes for v6:
- add psci node
Changes for v5:
- none
Changes for v4:
- update i2c0
- rebase on -next
Changes for v3:
- update cru and power file names
Changes for v2:
- split pinctrl in separate patch
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++++++++++++++++++
1 file changed, 438 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
diff --git a/arch/arm/boot/dts/rv1126.dtsi b/arch/arm/boot/dts/rv1126.dtsi
new file mode 100644
index 000000000000..1cb43147e90b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126.dtsi
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+#include <dt-bindings/clock/rockchip,rv1126-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rockchip,rv1126-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "rockchip,rv1126";
+
+ interrupt-parent = <&gic>;
+
+ aliases {
+ i2c0 = &i2c0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ grf: syscon@fe000000 {
+ compatible = "rockchip,rv1126-grf", "syscon", "simple-mfd";
+ reg = <0xfe000000 0x20000>;
+ };
+
+ pmugrf: syscon@fe020000 {
+ compatible = "rockchip,rv1126-pmugrf", "syscon", "simple-mfd";
+ reg = <0xfe020000 0x1000>;
+
+ pmu_io_domains: io-domains {
+ compatible = "rockchip,rv1126-pmu-io-voltage-domain";
+ status = "disabled";
+ };
+ };
+
+ qos_emmc: qos@fe860000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860000 0x20>;
+ };
+
+ qos_nandc: qos@fe860080 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860080 0x20>;
+ };
+
+ qos_sfc: qos@fe860200 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860200 0x20>;
+ };
+
+ qos_sdio: qos@fe86c000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe86c000 0x20>;
+ };
+
+ gic: interrupt-controller@feff0000 {
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+
+ reg = <0xfeff1000 0x1000>,
+ <0xfeff2000 0x2000>,
+ <0xfeff4000 0x2000>,
+ <0xfeff6000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ pmu: power-management@ff3e0000 {
+ compatible = "rockchip,rv1126-pmu", "syscon", "simple-mfd";
+ reg = <0xff3e0000 0x1000>;
+
+ power: power-controller {
+ compatible = "rockchip,rv1126-power-controller";
+ #power-domain-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-domain@RV1126_PD_NVM {
+ reg = <RV1126_PD_NVM>;
+ clocks = <&cru HCLK_EMMC>,
+ <&cru CLK_EMMC>,
+ <&cru HCLK_NANDC>,
+ <&cru CLK_NANDC>,
+ <&cru HCLK_SFC>,
+ <&cru HCLK_SFCXIP>,
+ <&cru SCLK_SFC>;
+ pm_qos = <&qos_emmc>,
+ <&qos_nandc>,
+ <&qos_sfc>;
+ #power-domain-cells = <0>;
+ };
+
+ power-domain@RV1126_PD_SDIO {
+ reg = <RV1126_PD_SDIO>;
+ clocks = <&cru HCLK_SDIO>,
+ <&cru CLK_SDIO>;
+ pm_qos = <&qos_sdio>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+
+ i2c0: i2c@ff3f0000 {
+ compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c";
+ reg = <0xff3f0000 0x1000>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ rockchip,grf = <&pmugrf>;
+ clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
+ clock-names = "i2c", "pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart1: serial@ff410000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff410000 0x100>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&pmucru SCLK_UART1>, <&pmucru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 7>, <&dmac 6>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ pmucru: clock-controller@ff480000 {
+ compatible = "rockchip,rv1126-pmucru";
+ reg = <0xff480000 0x1000>;
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ cru: clock-controller@ff490000 {
+ compatible = "rockchip,rv1126-cru";
+ reg = <0xff490000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ dmac: dma-controller@ff4e0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0xff4e0000 0x4000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ arm,pl330-periph-burst;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ };
+
+ uart0: serial@ff560000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff560000 0x100>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 5>, <&dmac 4>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart2: serial@ff570000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff570000 0x100>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 9>, <&dmac 8>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m1_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart3: serial@ff580000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff580000 0x100>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 11>, <&dmac 10>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart4: serial@ff590000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff590000 0x100>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 13>, <&dmac 12>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart5: serial@ff5a0000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff5a0000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 15>, <&dmac 14>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ saradc: adc@ff5e0000 {
+ compatible = "rockchip,rv1126-saradc", "rockchip,rk3399-saradc";
+ reg = <0xff5e0000 0x100>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ #io-channel-cells = <1>;
+ clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC_P>;
+ reset-names = "saradc-apb";
+ status = "disabled";
+ };
+
+ timer0: timer@ff660000 {
+ compatible = "rockchip,rv1126-timer", "rockchip,rk3288-timer";
+ reg = <0xff660000 0x20>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&cru CLK_TIMER0>;
+ clock-names = "pclk", "timer";
+ };
+
+ emmc: mmc@ffc50000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc50000 0x4000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru CLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_NVM>;
+ status = "disabled";
+ };
+
+ sdmmc: mmc@ffc60000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc60000 0x4000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru CLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ status = "disabled";
+ };
+
+ sdio: mmc@ffc70000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc70000 0x4000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru CLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_SDIO>;
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rv1126-pinctrl";
+ rockchip,grf = <&grf>;
+ rockchip,pmu = <&pmugrf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@ff460000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff460000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@ff620000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff620000 0x100>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@ff630000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff630000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@ff640000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff640000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@ff650000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff650000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+#include "rv1126-pinctrl.dtsi"
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 4/8] ARM: dts: rockchip: Add Rockchip RV1126 SoC
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Jon Lin, Sugar Zhang
RV1126 is a high-performance vision processor SoC for IPC/CVR,
especially for AI related application.
It is based on quad-core ARM Cortex-A7 32-bit core which integrates
NEON and FPU. There is a 32KB I-cache and 32KB D-cache for each core
and 512KB unified L2 cache. It has build-in NPU supports INT8/INT16
hybrid operation and computing power is up to 2.0TOPs.
This patch add basic core dtsi support.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- fix rv1126 dtsi
- remove uart aliases
- add adc node name
- add uart dma-names
- add timer0 node name
Changes for v7:
- fix dtbs_check
- rearrange nodes
- remove Edegble in license text
Changes for v6:
- add psci node
Changes for v5:
- none
Changes for v4:
- update i2c0
- rebase on -next
Changes for v3:
- update cru and power file names
Changes for v2:
- split pinctrl in separate patch
arch/arm/boot/dts/rv1126.dtsi | 438 ++++++++++++++++++++++++++++++++++
1 file changed, 438 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126.dtsi
diff --git a/arch/arm/boot/dts/rv1126.dtsi b/arch/arm/boot/dts/rv1126.dtsi
new file mode 100644
index 000000000000..1cb43147e90b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126.dtsi
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+#include <dt-bindings/clock/rockchip,rv1126-cru.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rockchip,rv1126-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "rockchip,rv1126";
+
+ interrupt-parent = <&gic>;
+
+ aliases {
+ i2c0 = &i2c0;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@f00 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf00>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu1: cpu@f01 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf01>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu2: cpu@f02 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf02>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+
+ cpu3: cpu@f03 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0xf03>;
+ enable-method = "psci";
+ clocks = <&cru ARMCLK>;
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clock-frequency = <24000000>;
+ };
+
+ xin24m: oscillator {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xin24m";
+ #clock-cells = <0>;
+ };
+
+ grf: syscon@fe000000 {
+ compatible = "rockchip,rv1126-grf", "syscon", "simple-mfd";
+ reg = <0xfe000000 0x20000>;
+ };
+
+ pmugrf: syscon@fe020000 {
+ compatible = "rockchip,rv1126-pmugrf", "syscon", "simple-mfd";
+ reg = <0xfe020000 0x1000>;
+
+ pmu_io_domains: io-domains {
+ compatible = "rockchip,rv1126-pmu-io-voltage-domain";
+ status = "disabled";
+ };
+ };
+
+ qos_emmc: qos@fe860000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860000 0x20>;
+ };
+
+ qos_nandc: qos@fe860080 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860080 0x20>;
+ };
+
+ qos_sfc: qos@fe860200 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe860200 0x20>;
+ };
+
+ qos_sdio: qos@fe86c000 {
+ compatible = "rockchip,rv1126-qos", "syscon";
+ reg = <0xfe86c000 0x20>;
+ };
+
+ gic: interrupt-controller@feff0000 {
+ compatible = "arm,gic-400";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+
+ reg = <0xfeff1000 0x1000>,
+ <0xfeff2000 0x2000>,
+ <0xfeff4000 0x2000>,
+ <0xfeff6000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ pmu: power-management@ff3e0000 {
+ compatible = "rockchip,rv1126-pmu", "syscon", "simple-mfd";
+ reg = <0xff3e0000 0x1000>;
+
+ power: power-controller {
+ compatible = "rockchip,rv1126-power-controller";
+ #power-domain-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-domain@RV1126_PD_NVM {
+ reg = <RV1126_PD_NVM>;
+ clocks = <&cru HCLK_EMMC>,
+ <&cru CLK_EMMC>,
+ <&cru HCLK_NANDC>,
+ <&cru CLK_NANDC>,
+ <&cru HCLK_SFC>,
+ <&cru HCLK_SFCXIP>,
+ <&cru SCLK_SFC>;
+ pm_qos = <&qos_emmc>,
+ <&qos_nandc>,
+ <&qos_sfc>;
+ #power-domain-cells = <0>;
+ };
+
+ power-domain@RV1126_PD_SDIO {
+ reg = <RV1126_PD_SDIO>;
+ clocks = <&cru HCLK_SDIO>,
+ <&cru CLK_SDIO>;
+ pm_qos = <&qos_sdio>;
+ #power-domain-cells = <0>;
+ };
+ };
+ };
+
+ i2c0: i2c@ff3f0000 {
+ compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c";
+ reg = <0xff3f0000 0x1000>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ rockchip,grf = <&pmugrf>;
+ clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
+ clock-names = "i2c", "pclk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_xfer>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ uart1: serial@ff410000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff410000 0x100>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&pmucru SCLK_UART1>, <&pmucru PCLK_UART1>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 7>, <&dmac 6>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ pmucru: clock-controller@ff480000 {
+ compatible = "rockchip,rv1126-pmucru";
+ reg = <0xff480000 0x1000>;
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ cru: clock-controller@ff490000 {
+ compatible = "rockchip,rv1126-cru";
+ reg = <0xff490000 0x1000>;
+ clocks = <&xin24m>;
+ clock-names = "xin24m";
+ rockchip,grf = <&grf>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ dmac: dma-controller@ff4e0000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0xff4e0000 0x4000>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ arm,pl330-periph-burst;
+ clocks = <&cru ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ };
+
+ uart0: serial@ff560000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff560000 0x100>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 5>, <&dmac 4>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart2: serial@ff570000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff570000 0x100>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 9>, <&dmac 8>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2m1_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart3: serial@ff580000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff580000 0x100>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 11>, <&dmac 10>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart4: serial@ff590000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff590000 0x100>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 13>, <&dmac 12>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ uart5: serial@ff5a0000 {
+ compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart";
+ reg = <0xff5a0000 0x100>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency = <24000000>;
+ clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
+ clock-names = "baudclk", "apb_pclk";
+ dmas = <&dmac 15>, <&dmac 14>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart5m0_xfer>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ status = "disabled";
+ };
+
+ saradc: adc@ff5e0000 {
+ compatible = "rockchip,rv1126-saradc", "rockchip,rk3399-saradc";
+ reg = <0xff5e0000 0x100>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ #io-channel-cells = <1>;
+ clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_SARADC_P>;
+ reset-names = "saradc-apb";
+ status = "disabled";
+ };
+
+ timer0: timer@ff660000 {
+ compatible = "rockchip,rv1126-timer", "rockchip,rk3288-timer";
+ reg = <0xff660000 0x20>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_TIMER>, <&cru CLK_TIMER0>;
+ clock-names = "pclk", "timer";
+ };
+
+ emmc: mmc@ffc50000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc50000 0x4000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_EMMC>, <&cru CLK_EMMC>,
+ <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_NVM>;
+ status = "disabled";
+ };
+
+ sdmmc: mmc@ffc60000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc60000 0x4000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDMMC>, <&cru CLK_SDMMC>,
+ <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ status = "disabled";
+ };
+
+ sdio: mmc@ffc70000 {
+ compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc";
+ reg = <0xffc70000 0x4000>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru HCLK_SDIO>, <&cru CLK_SDIO>,
+ <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
+ clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+ fifo-depth = <0x100>;
+ max-frequency = <200000000>;
+ power-domains = <&power RV1126_PD_SDIO>;
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl {
+ compatible = "rockchip,rv1126-pinctrl";
+ rockchip,grf = <&grf>;
+ rockchip,pmu = <&pmugrf>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gpio0: gpio@ff460000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff460000 0x100>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio1: gpio@ff620000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff620000 0x100>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio@ff630000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff630000 0x100>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio@ff640000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff640000 0x100>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio@ff650000 {
+ compatible = "rockchip,gpio-bank";
+ reg = <0xff650000 0x100>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
+
+#include "rv1126-pinctrl.dtsi"
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 5/8] dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Edgeble AI is an Artificial Intelligence company with a focus on
deploying Neural Acceleration principles at the Edge.
Add vendor prefix for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7, v6:
- none
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index c601f5438b02..dfc071548e91 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -370,6 +370,8 @@ patternProperties:
description: EBV Elektronik
"^eckelmann,.*":
description: Eckelmann AG
+ "^edgeble,.*":
+ description: Edgeble AI Technologies Pvt. Ltd.
"^edimax,.*":
description: EDIMAX Technology Co., Ltd
"^edt,.*":
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 5/8] dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Edgeble AI is an Artificial Intelligence company with a focus on
deploying Neural Acceleration principles at the Edge.
Add vendor prefix for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7, v6:
- none
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index c601f5438b02..dfc071548e91 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -370,6 +370,8 @@ patternProperties:
description: EBV Elektronik
"^eckelmann,.*":
description: Eckelmann AG
+ "^edgeble,.*":
+ description: Edgeble AI Technologies Pvt. Ltd.
"^edimax,.*":
description: EDIMAX Technology Co., Ltd
"^edt,.*":
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 5/8] dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd.
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Edgeble AI is an Artificial Intelligence company with a focus on
deploying Neural Acceleration principles at the Edge.
Add vendor prefix for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7, v6:
- none
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index c601f5438b02..dfc071548e91 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -370,6 +370,8 @@ patternProperties:
description: EBV Elektronik
"^eckelmann,.*":
description: Eckelmann AG
+ "^edgeble,.*":
+ description: Edgeble AI Technologies Pvt. Ltd.
"^edimax,.*":
description: EDIMAX Technology Co., Ltd
"^edt,.*":
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 6/8] dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
Edgeble Neural Compute Module 2(Neu2) IO board is an industrial
form factor evaluation board from Edgeble AI.
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add dt-bindings for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- collect Rob Ack
Changes for v6:
- updated SOM and Carrier name
Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 244c42eaae8c..26fdd205a899 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -85,6 +85,12 @@ properties:
- const: chipspark,rayeager-px2
- const: rockchip,rk3066a
+ - description: Edgeble Neural Compute Module 2(Neu2) SoM based boards
+ items:
+ - const: edgeble,neural-compute-module-2-io # Edgeble Neural Compute Module 2 IO Board
+ - const: edgeble,neural-compute-module-2 # Edgeble Neural Compute Module 2 SoM
+ - const: rockchip,rv1126
+
- description: Elgin RV1108 R1
items:
- const: elgin,rv1108-r1
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 6/8] dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
Edgeble Neural Compute Module 2(Neu2) IO board is an industrial
form factor evaluation board from Edgeble AI.
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add dt-bindings for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- collect Rob Ack
Changes for v6:
- updated SOM and Carrier name
Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 244c42eaae8c..26fdd205a899 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -85,6 +85,12 @@ properties:
- const: chipspark,rayeager-px2
- const: rockchip,rk3066a
+ - description: Edgeble Neural Compute Module 2(Neu2) SoM based boards
+ items:
+ - const: edgeble,neural-compute-module-2-io # Edgeble Neural Compute Module 2 IO Board
+ - const: edgeble,neural-compute-module-2 # Edgeble Neural Compute Module 2 SoM
+ - const: rockchip,rv1126
+
- description: Elgin RV1108 R1
items:
- const: elgin,rv1108-r1
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 6/8] dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki, Rob Herring
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
Edgeble Neural Compute Module 2(Neu2) IO board is an industrial
form factor evaluation board from Edgeble AI.
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add dt-bindings for it.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- collect Rob Ack
Changes for v6:
- updated SOM and Carrier name
Documentation/devicetree/bindings/arm/rockchip.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 244c42eaae8c..26fdd205a899 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -85,6 +85,12 @@ properties:
- const: chipspark,rayeager-px2
- const: rockchip,rk3066a
+ - description: Edgeble Neural Compute Module 2(Neu2) SoM based boards
+ items:
+ - const: edgeble,neural-compute-module-2-io # Edgeble Neural Compute Module 2 IO Board
+ - const: edgeble,neural-compute-module-2 # Edgeble Neural Compute Module 2 SoM
+ - const: rockchip,rv1126
+
- description: Elgin RV1108 R1
items:
- const: elgin,rv1108-r1
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 7/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- fix dtbs_check
Changes for v6:
- updated the SOM name
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 +++++++++++++++++++++
1 file changed, 338 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
new file mode 100644
index 000000000000..7db3f8bb581d
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+ compatible = "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ aliases {
+ mmc0 = &emmc;
+ };
+
+ vcc5v0_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vccio_flash: regulator-vccio-flash {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_vol_sel>;
+ regulator-name = "vccio_flash";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ sdio_pwrseq: pwrseq-sdio {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+ rockchip,default-sample-phase = <90>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_flash>;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_buck5>;
+ vcc6-supply = <&vcc_buck5>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_npu_vepu: DCDC_REG1 {
+ regulator-name = "vdd_npu_vepu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc3v3_sys: DCDC_REG4 {
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_buck5: DCDC_REG5 {
+ regulator-name = "vcc_buck5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2200000>;
+ };
+ };
+
+ vcc_0v8: LDO_REG1 {
+ regulator-name = "vcc_0v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG2 {
+ regulator-name = "vcc1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd0v8_pmu: LDO_REG3 {
+ regulator-name = "vcc0v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <800000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG4 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_dovdd: LDO_REG5 {
+ regulator-name = "vcc_dovdd";
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_dvdd: LDO_REG6 {
+ regulator-name = "vcc_dvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_avdd: LDO_REG7 {
+ regulator-name = "vcc_avdd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG8 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: LDO_REG9 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_5v0: SWITCH_REG1 {
+ regulator-name = "vcc_5v0";
+ };
+
+ vcc_3v3: SWITCH_REG2 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ bt {
+ bt_enable: bt-enable {
+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ flash {
+ flash_vol_sel: flash-vol-sel {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio0-supply = <&vcc1v8_pmu>;
+ pmuio1-supply = <&vcc3v3_sys>;
+ vccio1-supply = <&vccio_flash>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_1v8>;
+ vccio4-supply = <&vcc_dovdd>;
+ vccio5-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_dovdd>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdio {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ max-frequency = <100000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca9377-bt";
+ clocks = <&rk809 1>;
+ enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; /* BT_RST */
+ max-speed = <2000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable>;
+ vddxo-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 7/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- fix dtbs_check
Changes for v6:
- updated the SOM name
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 +++++++++++++++++++++
1 file changed, 338 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
new file mode 100644
index 000000000000..7db3f8bb581d
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+ compatible = "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ aliases {
+ mmc0 = &emmc;
+ };
+
+ vcc5v0_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vccio_flash: regulator-vccio-flash {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_vol_sel>;
+ regulator-name = "vccio_flash";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ sdio_pwrseq: pwrseq-sdio {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+ rockchip,default-sample-phase = <90>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_flash>;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_buck5>;
+ vcc6-supply = <&vcc_buck5>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_npu_vepu: DCDC_REG1 {
+ regulator-name = "vdd_npu_vepu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc3v3_sys: DCDC_REG4 {
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_buck5: DCDC_REG5 {
+ regulator-name = "vcc_buck5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2200000>;
+ };
+ };
+
+ vcc_0v8: LDO_REG1 {
+ regulator-name = "vcc_0v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG2 {
+ regulator-name = "vcc1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd0v8_pmu: LDO_REG3 {
+ regulator-name = "vcc0v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <800000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG4 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_dovdd: LDO_REG5 {
+ regulator-name = "vcc_dovdd";
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_dvdd: LDO_REG6 {
+ regulator-name = "vcc_dvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_avdd: LDO_REG7 {
+ regulator-name = "vcc_avdd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG8 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: LDO_REG9 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_5v0: SWITCH_REG1 {
+ regulator-name = "vcc_5v0";
+ };
+
+ vcc_3v3: SWITCH_REG2 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ bt {
+ bt_enable: bt-enable {
+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ flash {
+ flash_vol_sel: flash-vol-sel {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio0-supply = <&vcc1v8_pmu>;
+ pmuio1-supply = <&vcc3v3_sys>;
+ vccio1-supply = <&vccio_flash>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_1v8>;
+ vccio4-supply = <&vcc_dovdd>;
+ vccio5-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_dovdd>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdio {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ max-frequency = <100000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca9377-bt";
+ clocks = <&rk809 1>;
+ enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; /* BT_RST */
+ max-speed = <2000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable>;
+ vddxo-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 7/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2)
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RV1126 from Edgeble AI.
General features:
- Rockchip RV1126
- 2/4GB LPDDR4
- 8/16/32GB eMMC
- 2x MIPI CSI2 FPC connector
- Fn-link 8223A-SR WiFi/BT
Industrial grade (-40 °C to +85 °C) version of the same class of module
called Neu2k powered with Rockchip RV1126K.
Neu2 needs to mount on top of Edgeble IO boards for creating complete
platform solutions.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8:
- none
Changes for v7:
- fix dtbs_check
Changes for v6:
- updated the SOM name
arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi | 338 +++++++++++++++++++++
1 file changed, 338 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
new file mode 100644
index 000000000000..7db3f8bb581d
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2.dtsi
@@ -0,0 +1,338 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/ {
+ compatible = "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ aliases {
+ mmc0 = &emmc;
+ };
+
+ vcc5v0_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vccio_flash: regulator-vccio-flash {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&flash_vol_sel>;
+ regulator-name = "vccio_flash";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ };
+
+ sdio_pwrseq: pwrseq-sdio {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
+ rockchip,default-sample-phase = <90>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vccio_flash>;
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_buck5>;
+ vcc6-supply = <&vcc_buck5>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_npu_vepu: DCDC_REG1 {
+ regulator-name = "vdd_npu_vepu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc3v3_sys: DCDC_REG4 {
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_buck5: DCDC_REG5 {
+ regulator-name = "vcc_buck5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2200000>;
+ };
+ };
+
+ vcc_0v8: LDO_REG1 {
+ regulator-name = "vcc_0v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc1v8_pmu: LDO_REG2 {
+ regulator-name = "vcc1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd0v8_pmu: LDO_REG3 {
+ regulator-name = "vcc0v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <800000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG4 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_dovdd: LDO_REG5 {
+ regulator-name = "vcc_dovdd";
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_dvdd: LDO_REG6 {
+ regulator-name = "vcc_dvdd";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_avdd: LDO_REG7 {
+ regulator-name = "vcc_avdd";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG8 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: LDO_REG9 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_5v0: SWITCH_REG1 {
+ regulator-name = "vcc_5v0";
+ };
+
+ vcc_3v3: SWITCH_REG2 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ bt {
+ bt_enable: bt-enable {
+ rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ flash {
+ flash_vol_sel: flash-vol-sel {
+ rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wifi_enable_h: wifi-enable-h {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio0-supply = <&vcc1v8_pmu>;
+ pmuio1-supply = <&vcc3v3_sys>;
+ vccio1-supply = <&vccio_flash>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_1v8>;
+ vccio4-supply = <&vcc_dovdd>;
+ vccio5-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_dovdd>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdio {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ max-frequency = <100000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_ctsn &uart0_rtsn>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca9377-bt";
+ clocks = <&rk809 1>;
+ enable-gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_HIGH>; /* BT_RST */
+ max-speed = <2000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable>;
+ vddxo-supply = <&vcc3v3_sys>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 8/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-23 18:31 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7:
- none
Changes for v6:
- update the carrier name.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++++++++++++++++++++
2 files changed, 39 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e48cfbc4e8e4..40cc34bd4945 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1122,6 +1122,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rv1108-elgin-r1.dtb \
rv1108-evb.dtb \
+ rv1126-edgeble-neu2-io.dtb \
rk3036-evb.dtb \
rk3036-kylin.dtb \
rk3066a-bqcurie2.dtb \
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
new file mode 100644
index 000000000000..ae1cf344239b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-edgeble-neu2.dtsi"
+
+/ {
+ model = "Edgeble Neu2 IO Board";
+ compatible = "edgeble,neural-compute-module-2-io",
+ "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr104;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 8/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7:
- none
Changes for v6:
- update the carrier name.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++++++++++++++++++++
2 files changed, 39 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e48cfbc4e8e4..40cc34bd4945 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1122,6 +1122,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rv1108-elgin-r1.dtb \
rv1108-evb.dtb \
+ rv1126-edgeble-neu2-io.dtb \
rk3036-evb.dtb \
rk3036-kylin.dtb \
rk3066a-bqcurie2.dtb \
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
new file mode 100644
index 000000000000..ae1cf344239b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-edgeble-neu2.dtsi"
+
+/ {
+ model = "Edgeble Neu2 IO Board";
+ compatible = "edgeble,neural-compute-module-2-io",
+ "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr104;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.25.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 37+ messages in thread
* [PATCH v8 8/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO
@ 2022-11-23 18:31 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-11-23 18:31 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker, Jagan Teki
Neural Compute Module 2(Neu2) IO board is an industrial form factor
evaluation board from Edgeble AI.
General features:
- microSD slot
- MIPI DSI connector
- 2x USB Host
- 1x USB OTG
- Ethernet
- mini PCIe
- Onboard PoE
- RS485, RS232, CAN
- Micro Phone array
- Speaker
- RTC battery slot
- 40-pin expansion
Neu2 needs to mount on top of this IO board in order to create complete
Edgeble Neural Compute Module 2(Neu2) IO platform.
Add support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
---
Changes for v8, v7:
- none
Changes for v6:
- update the carrier name.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts | 38 ++++++++++++++++++++
2 files changed, 39 insertions(+)
create mode 100644 arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e48cfbc4e8e4..40cc34bd4945 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1122,6 +1122,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rv1108-elgin-r1.dtb \
rv1108-evb.dtb \
+ rv1126-edgeble-neu2-io.dtb \
rk3036-evb.dtb \
rk3036-kylin.dtb \
rk3066a-bqcurie2.dtb \
diff --git a/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
new file mode 100644
index 000000000000..ae1cf344239b
--- /dev/null
+++ b/arch/arm/boot/dts/rv1126-edgeble-neu2-io.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
+ */
+
+/dts-v1/;
+#include "rv1126.dtsi"
+#include "rv1126-edgeble-neu2.dtsi"
+
+/ {
+ model = "Edgeble Neu2 IO Board";
+ compatible = "edgeble,neural-compute-module-2-io",
+ "edgeble,neural-compute-module-2", "rockchip,rv1126";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_bus4 &sdmmc0_det>;
+ rockchip,default-sample-phase = <90>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr104;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-11-24 11:22 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 37+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-24 11:22 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker
On 23/11/2022 19:31, Jagan Teki wrote:
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-11-24 11:22 ` Krzysztof Kozlowski
0 siblings, 0 replies; 37+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-24 11:22 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker
On 23/11/2022 19:31, Jagan Teki wrote:
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-11-24 11:22 ` Krzysztof Kozlowski
0 siblings, 0 replies; 37+ messages in thread
From: Krzysztof Kozlowski @ 2022-11-24 11:22 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: Daniel Lezcano, linux-arm-kernel, linux-rockchip, devicetree,
Johan Jonker
On 23/11/2022 19:31, Jagan Teki wrote:
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
2022-11-23 18:31 ` Jagan Teki
(?)
@ 2022-12-13 7:50 ` Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-12-13 7:50 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Daniel Lezcano
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Daniel or Can someone please pick this? Heiko is holding this series
due to this patch.
Jagan.
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-12-13 7:50 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-12-13 7:50 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Daniel Lezcano
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Daniel or Can someone please pick this? Heiko is holding this series
due to this patch.
Jagan.
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-12-13 7:50 ` Jagan Teki
0 siblings, 0 replies; 37+ messages in thread
From: Jagan Teki @ 2022-12-13 7:50 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Daniel Lezcano
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>
> Add rockchip timer compatible string for rockchip rv1126.
>
> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
> ---
Daniel or Can someone please pick this? Heiko is holding this series
due to this patch.
Jagan.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
2022-12-13 7:50 ` Jagan Teki
(?)
@ 2022-12-13 8:48 ` Daniel Lezcano
-1 siblings, 0 replies; 37+ messages in thread
From: Daniel Lezcano @ 2022-12-13 8:48 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On 13/12/2022 08:50, Jagan Teki wrote:
> On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>>
>> Add rockchip timer compatible string for rockchip rv1126.
>>
>> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
>> ---
>
> Daniel or Can someone please pick this? Heiko is holding this series
> due to this patch.
Applied, with a trivial conflict fix
Thanks
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-12-13 8:48 ` Daniel Lezcano
0 siblings, 0 replies; 37+ messages in thread
From: Daniel Lezcano @ 2022-12-13 8:48 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On 13/12/2022 08:50, Jagan Teki wrote:
> On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>>
>> Add rockchip timer compatible string for rockchip rv1126.
>>
>> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
>> ---
>
> Daniel or Can someone please pick this? Heiko is holding this series
> due to this patch.
Applied, with a trivial conflict fix
Thanks
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 37+ messages in thread
* Re: [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer for rv1126
@ 2022-12-13 8:48 ` Daniel Lezcano
0 siblings, 0 replies; 37+ messages in thread
From: Daniel Lezcano @ 2022-12-13 8:48 UTC (permalink / raw)
To: Jagan Teki, Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
Cc: linux-arm-kernel, linux-rockchip, devicetree, Johan Jonker
On 13/12/2022 08:50, Jagan Teki wrote:
> On Thu, 24 Nov 2022 at 00:02, Jagan Teki <jagan@edgeble.ai> wrote:
>>
>> Add rockchip timer compatible string for rockchip rv1126.
>>
>> Signed-off-by: Jagan Teki <jagan@edgeble.ai>
>> ---
>
> Daniel or Can someone please pick this? Heiko is holding this series
> due to this patch.
Applied, with a trivial conflict fix
Thanks
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 37+ messages in thread
* [tip: timers/core] dt-bindings: timer: rk-timer: Add rktimer for rv1126
2022-11-23 18:31 ` Jagan Teki
` (3 preceding siblings ...)
(?)
@ 2023-02-13 18:26 ` tip-bot2 for Jagan Teki
-1 siblings, 0 replies; 37+ messages in thread
From: tip-bot2 for Jagan Teki @ 2023-02-13 18:26 UTC (permalink / raw)
To: linux-tip-commits
Cc: Jagan Teki, Krzysztof Kozlowski, Daniel Lezcano, x86, linux-kernel
The following commit has been merged into the timers/core branch of tip:
Commit-ID: b3cbfb7927922e4586f890a70a22f13130247b4e
Gitweb: https://git.kernel.org/tip/b3cbfb7927922e4586f890a70a22f13130247b4e
Author: Jagan Teki <jagan@edgeble.ai>
AuthorDate: Thu, 24 Nov 2022 00:01:18 +05:30
Committer: Daniel Lezcano <daniel.lezcano@linaro.org>
CommitterDate: Mon, 13 Feb 2023 13:10:16 +01:00
dt-bindings: timer: rk-timer: Add rktimer for rv1126
Add rockchip timer compatible string for rockchip rv1126.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221123183124.6911-3-jagan@edgeble.ai
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
---
Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
index b61ed1a..65e5983 100644
--- a/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/rockchip,rk-timer.yaml
@@ -17,6 +17,7 @@ properties:
- items:
- enum:
- rockchip,rv1108-timer
+ - rockchip,rv1126-timer
- rockchip,rk3036-timer
- rockchip,rk3128-timer
- rockchip,rk3188-timer
^ permalink raw reply related [flat|nested] 37+ messages in thread
end of thread, other threads:[~2023-02-13 18:27 UTC | newest]
Thread overview: 37+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-23 18:31 [PATCH v8 0/8] ARM: Add Rockchip RV1126 support Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 1/8] dt-bindings: arm: rockchip: Add pmu compatible for rv1126 Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 2/8] dt-bindings: timer: rk-timer: Add rktimer " Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-24 11:22 ` Krzysztof Kozlowski
2022-11-24 11:22 ` Krzysztof Kozlowski
2022-11-24 11:22 ` Krzysztof Kozlowski
2022-12-13 7:50 ` Jagan Teki
2022-12-13 7:50 ` Jagan Teki
2022-12-13 7:50 ` Jagan Teki
2022-12-13 8:48 ` Daniel Lezcano
2022-12-13 8:48 ` Daniel Lezcano
2022-12-13 8:48 ` Daniel Lezcano
2023-02-13 18:26 ` [tip: timers/core] " tip-bot2 for Jagan Teki
2022-11-23 18:31 ` [PATCH v8 3/8] ARM: dts: rockchip: Add Rockchip RV1126 pinctrl Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 4/8] ARM: dts: rockchip: Add Rockchip RV1126 SoC Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 5/8] dt-bindings: vendor-prefixes: Add Edgeble AI Technologies Pvt. Ltd Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 6/8] dt-bindings: arm: rockchip: Add Edgeble Neural Compute Module 2 Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 7/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` [PATCH v8 8/8] ARM: dts: rockchip: rv1126: Add Edgeble Neural Compute Module 2(Neu2) IO Jagan Teki
2022-11-23 18:31 ` Jagan Teki
2022-11-23 18:31 ` Jagan Teki
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.