Revised patch series for minimal HTC Dream support

Revised patch series for minimal HTC Dream support

[Brian Swetland]

This incorporates feedback from lkml/lakml, and I think is in
pretty good shape now.

msm_serial.c
- Ryan Mallon
  - remove some likely/unlikely not in hot-path code, for clarity
  - UART_TO_MSM() -> to_msm_uart()
  - clean up static structure declarations
- Pavel Machek
  - SUPPORT_SYSRQ needed for console break handling
  - remove hrtimer.h, other unused headers
  - Kconfig cleanup
- Alan Cox
  - set_termios should propogate used settings
- Linus Walleij
  - use resource_size() when appropriate
  - dev_err instead of printk(KERN_ERR...
  - remove some chatty printks
  - use __exit, __exit_p()

board-dream.c
- Stefan Schmidt
  - remove smc resources
  - remove unused headers

ll debug support
- Pavel Machek
  - remove extraneous 1002 label

[PATCH 1/3] [ARM] msm_serial: serial driver for MSM7K onboard serial peripheral.

[Brian Swetland]

From: Robert Love <rlove@google.com>

Provides support for the "lowspeed" UARTs on the MSM7k and QSD8k
family of SoCs from Qualcomm.  Serial console support included.

Signed-off-by: Robert Love <rlove@google.com>
Signed-off-by: Brian Swetland <swetland@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 drivers/serial/Kconfig      |   10 +
 drivers/serial/Makefile     |    1 +
 drivers/serial/msm_serial.c |  762 +++++++++++++++++++++++++++++++++++++++++++
 drivers/serial/msm_serial.h |  117 +++++++
 include/linux/serial_core.h |    3 +
 5 files changed, 893 insertions(+), 0 deletions(-)
 create mode 100644 drivers/serial/msm_serial.c
 create mode 100644 drivers/serial/msm_serial.h

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 1132c5c..1e3cc15 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1320,6 +1320,16 @@ config SERIAL_SGI_IOC3
 	  If you have an SGI Altix with an IOC3 serial card,
 	  say Y or M.  Otherwise, say N.
 
+config SERIAL_MSM
+	bool "MSM on-chip serial port support"
+	depends on ARM && ARCH_MSM
+	select SERIAL_CORE
+
+config SERIAL_MSM_CONSOLE
+	bool "MSM serial console support"
+	depends on SERIAL_MSM
+	select SERIAL_CORE_CONSOLE
+
 config SERIAL_NETX
 	tristate "NetX serial port support"
 	depends on ARM && ARCH_NETX
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 45a8658..d5a2998 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -71,6 +71,7 @@ obj-$(CONFIG_SERIAL_SGI_IOC4) += ioc4_serial.o
 obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
 obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
 obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
+obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
 obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
diff --git a/drivers/serial/msm_serial.c b/drivers/serial/msm_serial.c
new file mode 100644
index 0000000..b0569d9
--- /dev/null
+++ b/drivers/serial/msm_serial.c
@@ -0,0 +1,762 @@
+/*
+ * drivers/serial/msm_serial.c - driver for msm7k serial device and console
+ *
+ * Copyright (C) 2007 Google, Inc.
+ * Author: Robert Love <rlove@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#if defined(CONFIG_SERIAL_MSM_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+# define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/clk.h>
+#include <linux/platform_device.h>
+
+#include "msm_serial.h"
+
+struct msm_port {
+	struct uart_port	uart;
+	char			name[16];
+	struct clk		*clk;
+	unsigned int		imr;
+};
+
+#define to_msm_uart(uart_port) ((struct msm_port *) uart_port)
+
+static inline void msm_write(struct uart_port *port, unsigned int val,
+			     unsigned int off)
+{
+	__raw_writel(val, port->membase + off);
+}
+
+static inline unsigned int msm_read(struct uart_port *port, unsigned int off)
+{
+	return __raw_readl(port->membase + off);
+}
+
+static void msm_stop_tx(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	msm_port->imr &= ~UART_IMR_TXLEV;
+	msm_write(port, msm_port->imr, UART_IMR);
+}
+
+static void msm_start_tx(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	msm_port->imr |= UART_IMR_TXLEV;
+	msm_write(port, msm_port->imr, UART_IMR);
+}
+
+static void msm_stop_rx(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	msm_port->imr &= ~(UART_IMR_RXLEV | UART_IMR_RXSTALE);
+	msm_write(port, msm_port->imr, UART_IMR);
+}
+
+static void msm_enable_ms(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	msm_port->imr |= UART_IMR_DELTA_CTS;
+	msm_write(port, msm_port->imr, UART_IMR);
+}
+
+static void handle_rx(struct uart_port *port)
+{
+	struct tty_struct *tty = port->info->port.tty;
+	unsigned int sr;
+
+	/*
+	 * Handle overrun. My understanding of the hardware is that overrun
+	 * is not tied to the RX buffer, so we handle the case out of band.
+	 */
+	if ((msm_read(port, UART_SR) & UART_SR_OVERRUN)) {
+		port->icount.overrun++;
+		tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+		msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR);
+	}
+
+	/* and now the main RX loop */
+	while ((sr = msm_read(port, UART_SR)) & UART_SR_RX_READY) {
+		unsigned int c;
+		char flag = TTY_NORMAL;
+
+		c = msm_read(port, UART_RF);
+
+		if (sr & UART_SR_RX_BREAK) {
+			port->icount.brk++;
+			if (uart_handle_break(port))
+				continue;
+		} else if (sr & UART_SR_PAR_FRAME_ERR) {
+			port->icount.frame++;
+		} else {
+			port->icount.rx++;
+		}
+
+		/* Mask conditions we're ignorning. */
+		sr &= port->read_status_mask;
+
+		if (sr & UART_SR_RX_BREAK) {
+			flag = TTY_BREAK;
+		} else if (sr & UART_SR_PAR_FRAME_ERR) {
+			flag = TTY_FRAME;
+		}
+
+		if (!uart_handle_sysrq_char(port, c))
+			tty_insert_flip_char(tty, c, flag);
+	}
+
+	tty_flip_buffer_push(tty);
+}
+
+static void handle_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->info->xmit;
+	struct msm_port *msm_port = to_msm_uart(port);
+	int sent_tx;
+
+	if (port->x_char) {
+		msm_write(port, port->x_char, UART_TF);
+		port->icount.tx++;
+		port->x_char = 0;
+	}
+
+	while (msm_read(port, UART_SR) & UART_SR_TX_READY) {
+		if (uart_circ_empty(xmit)) {
+			/* disable tx interrupts */
+			msm_port->imr &= ~UART_IMR_TXLEV;
+			msm_write(port, msm_port->imr, UART_IMR);
+			break;
+		}
+
+		msm_write(port, xmit->buf[xmit->tail], UART_TF);
+
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		port->icount.tx++;
+		sent_tx = 1;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+}
+
+static void handle_delta_cts(struct uart_port *port)
+{
+	msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR);
+	port->icount.cts++;
+	wake_up_interruptible(&port->info->delta_msr_wait);
+}
+
+static irqreturn_t msm_irq(int irq, void *dev_id)
+{
+	struct uart_port *port = dev_id;
+	struct msm_port *msm_port = to_msm_uart(port);
+	unsigned int misr;
+
+	spin_lock(&port->lock);
+	misr = msm_read(port, UART_MISR);
+	msm_write(port, 0, UART_IMR); /* disable interrupt */
+
+	if (misr & (UART_IMR_RXLEV | UART_IMR_RXSTALE))
+		handle_rx(port);
+	if (misr & UART_IMR_TXLEV)
+		handle_tx(port);
+	if (misr & UART_IMR_DELTA_CTS)
+		handle_delta_cts(port);
+
+	msm_write(port, msm_port->imr, UART_IMR); /* restore interrupt */
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int msm_tx_empty(struct uart_port *port)
+{
+	return (msm_read(port, UART_SR) & UART_SR_TX_EMPTY) ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int msm_get_mctrl(struct uart_port *port)
+{
+	return TIOCM_CAR | TIOCM_CTS | TIOCM_DSR | TIOCM_RTS;
+}
+
+static void msm_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	unsigned int mr;
+
+	mr = msm_read(port, UART_MR1);
+
+	if (!(mctrl & TIOCM_RTS)) {
+		mr &= ~UART_MR1_RX_RDY_CTL;
+		msm_write(port, mr, UART_MR1);
+		msm_write(port, UART_CR_CMD_RESET_RFR, UART_CR);
+	} else {
+		mr |= UART_MR1_RX_RDY_CTL;
+		msm_write(port, mr, UART_MR1);
+	}
+}
+
+static void msm_break_ctl(struct uart_port *port, int break_ctl)
+{
+	if (break_ctl)
+		msm_write(port, UART_CR_CMD_START_BREAK, UART_CR);
+	else
+		msm_write(port, UART_CR_CMD_STOP_BREAK, UART_CR);
+}
+
+static int msm_set_baud_rate(struct uart_port *port, unsigned int baud)
+{
+	unsigned int baud_code, rxstale, watermark;
+
+	switch (baud) {
+	case 300:
+		baud_code = UART_CSR_300;
+		rxstale = 1;
+		break;
+	case 600:
+		baud_code = UART_CSR_600;
+		rxstale = 1;
+		break;
+	case 1200:
+		baud_code = UART_CSR_1200;
+		rxstale = 1;
+		break;
+	case 2400:
+		baud_code = UART_CSR_2400;
+		rxstale = 1;
+		break;
+	case 4800:
+		baud_code = UART_CSR_4800;
+		rxstale = 1;
+		break;
+	case 9600:
+		baud_code = UART_CSR_9600;
+		rxstale = 2;
+		break;
+	case 14400:
+		baud_code = UART_CSR_14400;
+		rxstale = 3;
+		break;
+	case 19200:
+		baud_code = UART_CSR_19200;
+		rxstale = 4;
+		break;
+	case 28800:
+		baud_code = UART_CSR_28800;
+		rxstale = 6;
+		break;
+	case 38400:
+		baud_code = UART_CSR_38400;
+		rxstale = 8;
+		break;
+	case 57600:
+		baud_code = UART_CSR_57600;
+		rxstale = 16;
+		break;
+	case 115200:
+	default:
+		baud_code = UART_CSR_115200;
+		baud = 115200;
+		rxstale = 31;
+		break;
+	}
+
+	msm_write(port, baud_code, UART_CSR);
+
+	/* RX stale watermark */
+	watermark = UART_IPR_STALE_LSB & rxstale;
+	watermark |= UART_IPR_RXSTALE_LAST;
+	watermark |= UART_IPR_STALE_TIMEOUT_MSB & (rxstale << 2);
+	msm_write(port, watermark, UART_IPR);
+
+	/* set RX watermark */
+	watermark = (port->fifosize * 3) / 4;
+	msm_write(port, watermark, UART_RFWR);
+
+	/* set TX watermark */
+	msm_write(port, 10, UART_TFWR);
+
+	return baud;
+}
+
+static void msm_reset(struct uart_port *port)
+{
+	/* reset everything */
+	msm_write(port, UART_CR_CMD_RESET_RX, UART_CR);
+	msm_write(port, UART_CR_CMD_RESET_TX, UART_CR);
+	msm_write(port, UART_CR_CMD_RESET_ERR, UART_CR);
+	msm_write(port, UART_CR_CMD_RESET_BREAK_INT, UART_CR);
+	msm_write(port, UART_CR_CMD_RESET_CTS, UART_CR);
+	msm_write(port, UART_CR_CMD_SET_RFR, UART_CR);
+}
+
+static void msm_init_clock(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	clk_enable(msm_port->clk);
+
+	msm_write(port, 0xC0, UART_MREG);
+	msm_write(port, 0xB2, UART_NREG);
+	msm_write(port, 0x7D, UART_DREG);
+	msm_write(port, 0x1C, UART_MNDREG);
+}
+
+static int msm_startup(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+	unsigned int data, rfr_level;
+	int ret;
+
+	snprintf(msm_port->name, sizeof(msm_port->name),
+		 "msm_serial%d", port->line);
+
+	ret = request_irq(port->irq, msm_irq, IRQF_TRIGGER_HIGH,
+			  msm_port->name, port);
+	if (ret)
+		return ret;
+
+	msm_init_clock(port);
+
+	if (port->fifosize > 12)
+		rfr_level = port->fifosize - 12;
+	else
+		rfr_level = port->fifosize;
+
+	/* set automatic RFR level */
+	data = msm_read(port, UART_MR1);
+	data &= ~UART_MR1_AUTO_RFR_LEVEL1;
+	data &= ~UART_MR1_AUTO_RFR_LEVEL0;
+	data |= UART_MR1_AUTO_RFR_LEVEL1 & (rfr_level << 2);
+	data |= UART_MR1_AUTO_RFR_LEVEL0 & rfr_level;
+	msm_write(port, data, UART_MR1);
+
+	/* make sure that RXSTALE count is non-zero */
+	data = msm_read(port, UART_IPR);
+	if (!data) {
+		data |= UART_IPR_RXSTALE_LAST;
+		data |= UART_IPR_STALE_LSB;
+		msm_write(port, data, UART_IPR);
+	}
+
+	msm_reset(port);
+
+	msm_write(port, 0x05, UART_CR);	/* enable TX & RX */
+
+	/* turn on RX and CTS interrupts */
+	msm_port->imr = UART_IMR_RXLEV | UART_IMR_RXSTALE |
+			UART_IMR_CURRENT_CTS;
+	msm_write(port, msm_port->imr, UART_IMR);
+
+	return 0;
+}
+
+static void msm_shutdown(struct uart_port *port)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	msm_port->imr = 0;
+	msm_write(port, 0, UART_IMR); /* disable interrupts */
+
+	clk_disable(msm_port->clk);
+
+	free_irq(port->irq, port);
+}
+
+static void msm_set_termios(struct uart_port *port, struct ktermios *termios,
+			    struct ktermios *old)
+{
+	unsigned long flags;
+	unsigned int baud, mr;
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* calculate and set baud rate */
+	baud = uart_get_baud_rate(port, termios, old, 300, 115200);
+	baud = msm_set_baud_rate(port, baud);
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, baud, baud);
+
+	/* calculate parity */
+	mr = msm_read(port, UART_MR2);
+	mr &= ~UART_MR2_PARITY_MODE;
+	if (termios->c_cflag & PARENB) {
+		if (termios->c_cflag & PARODD)
+			mr |= UART_MR2_PARITY_MODE_ODD;
+		else if (termios->c_cflag & CMSPAR)
+			mr |= UART_MR2_PARITY_MODE_SPACE;
+		else
+			mr |= UART_MR2_PARITY_MODE_EVEN;
+	}
+
+	/* calculate bits per char */
+	mr &= ~UART_MR2_BITS_PER_CHAR;
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		mr |= UART_MR2_BITS_PER_CHAR_5;
+		break;
+	case CS6:
+		mr |= UART_MR2_BITS_PER_CHAR_6;
+		break;
+	case CS7:
+		mr |= UART_MR2_BITS_PER_CHAR_7;
+		break;
+	case CS8:
+	default:
+		mr |= UART_MR2_BITS_PER_CHAR_8;
+		break;
+	}
+
+	/* calculate stop bits */
+	mr &= ~(UART_MR2_STOP_BIT_LEN_ONE | UART_MR2_STOP_BIT_LEN_TWO);
+	if (termios->c_cflag & CSTOPB)
+		mr |= UART_MR2_STOP_BIT_LEN_TWO;
+	else
+		mr |= UART_MR2_STOP_BIT_LEN_ONE;
+
+	/* set parity, bits per char, and stop bit */
+	msm_write(port, mr, UART_MR2);
+
+	/* calculate and set hardware flow control */
+	mr = msm_read(port, UART_MR1);
+	mr &= ~(UART_MR1_CTS_CTL | UART_MR1_RX_RDY_CTL);
+	if (termios->c_cflag & CRTSCTS) {
+		mr |= UART_MR1_CTS_CTL;
+		mr |= UART_MR1_RX_RDY_CTL;
+	}
+	msm_write(port, mr, UART_MR1);
+
+	/* Configure status bits to ignore based on termio flags. */
+	port->read_status_mask = 0;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= UART_SR_PAR_FRAME_ERR;
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		port->read_status_mask |= UART_SR_RX_BREAK;
+
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *msm_type(struct uart_port *port)
+{
+	return "MSM";
+}
+
+static void msm_release_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *resource;
+
+	resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!resource)
+		return;
+
+	release_mem_region(port->mapbase, resource_size(resource));
+	iounmap(port->membase);
+	port->membase = NULL;
+}
+
+static int msm_request_port(struct uart_port *port)
+{
+	struct platform_device *pdev = to_platform_device(port->dev);
+	struct resource *resource;
+	resource_size_t size;
+
+	resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!resource)
+		return -ENXIO;
+	size = resource_size(resource);
+
+	if (!request_mem_region(port->mapbase, size, "msm_serial"))
+		return -EBUSY;
+
+	port->membase = ioremap(port->mapbase, size);
+	if (!port->membase) {
+		release_mem_region(port->mapbase, size);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void msm_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE) {
+		port->type = PORT_MSM;
+		msm_request_port(port);
+	}
+}
+
+static int msm_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_MSM)
+		return -EINVAL;
+	if (port->irq != ser->irq)
+		return -EINVAL;
+	return 0;
+}
+
+static void msm_power(struct uart_port *port, unsigned int state,
+		      unsigned int oldstate)
+{
+	struct msm_port *msm_port = to_msm_uart(port);
+
+	switch (state) {
+	case 0:
+		clk_enable(msm_port->clk);
+		break;
+	case 3:
+		clk_disable(msm_port->clk);
+		break;
+	default:
+		dev_err(port->dev, "Unknown PM state %d\n", state);
+	}
+}
+
+static struct uart_ops msm_uart_pops = {
+	.tx_empty	= msm_tx_empty,
+	.set_mctrl	= msm_set_mctrl,
+	.get_mctrl	= msm_get_mctrl,
+	.stop_tx	= msm_stop_tx,
+	.start_tx	= msm_start_tx,
+	.stop_rx	= msm_stop_rx,
+	.enable_ms	= msm_enable_ms,
+	.break_ctl	= msm_break_ctl,
+	.startup	= msm_startup,
+	.shutdown	= msm_shutdown,
+	.set_termios	= msm_set_termios,
+	.type		= msm_type,
+	.release_port	= msm_release_port,
+	.request_port	= msm_request_port,
+	.config_port	= msm_config_port,
+	.verify_port	= msm_verify_port,
+	.pm		= msm_power,
+};
+
+static struct msm_port msm_uart_ports[] = {
+	{
+		.uart = {
+			.iotype		= UPIO_MEM,
+			.ops		= &msm_uart_pops,
+			.flags		= UPF_BOOT_AUTOCONF,
+			.fifosize 	= 512,
+			.line		= 0,
+		},
+	},
+	{
+		.uart = {
+			.iotype		= UPIO_MEM,
+			.ops		= &msm_uart_pops,
+			.flags		= UPF_BOOT_AUTOCONF,
+			.fifosize	= 512,
+			.line		= 1,
+		},
+	},
+	{
+		.uart = {
+			.iotype		= UPIO_MEM,
+			.ops		= &msm_uart_pops,
+			.flags		= UPF_BOOT_AUTOCONF,
+			.fifosize	= 64,
+			.line		= 2,
+		},
+	},
+};
+
+#define UART_NR	ARRAY_SIZE(msm_uart_ports)
+
+static inline struct uart_port *get_port_from_line(unsigned int line)
+{
+	return &msm_uart_ports[line].uart;
+}
+
+#ifdef CONFIG_SERIAL_MSM_CONSOLE
+
+static void msm_console_putchar(struct uart_port *port, int c)
+{
+	while (!(msm_read(port, UART_SR) & UART_SR_TX_READY))
+		;
+	msm_write(port, c, UART_TF);
+}
+
+static void msm_console_write(struct console *co, const char *s,
+			      unsigned int count)
+{
+	struct uart_port *port;
+	struct msm_port *msm_port;
+
+	BUG_ON(co->index < 0 || co->index >= UART_NR);
+
+	port = get_port_from_line(co->index);
+	msm_port = to_msm_uart(port);
+
+	spin_lock(&port->lock);
+	uart_console_write(port, s, count, msm_console_putchar);
+	spin_unlock(&port->lock);
+}
+
+static int __init msm_console_setup(struct console *co, char *options)
+{
+	struct uart_port *port;
+	int baud, flow, bits, parity;
+
+	if (co->index >= UART_NR || co->index < 0)
+		return -ENXIO;
+
+	port = get_port_from_line(co->index);
+
+	if (!port->membase)
+		return -ENXIO;
+
+	port->cons = co;
+
+	msm_init_clock(port);
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	bits = 8;
+	parity = 'n';
+	flow = 'n';
+	msm_write(port, UART_MR2_BITS_PER_CHAR_8 | UART_MR2_STOP_BIT_LEN_ONE,
+		  UART_MR2);	/* 8N1 */
+
+	if (baud < 300 || baud > 115200)
+		baud = 115200;
+	msm_set_baud_rate(port, baud);
+
+	msm_reset(port);
+
+	return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver msm_uart_driver;
+
+static struct console msm_console = {
+	.name	= "ttyMSM",
+	.write	= msm_console_write,
+	.device	= uart_console_device,
+	.setup	= msm_console_setup,
+	.flags	= CON_PRINTBUFFER,
+	.index	= -1,
+	.data	= &msm_uart_driver,
+};
+
+#define MSM_CONSOLE	(&msm_console)
+
+#else
+#define MSM_CONSOLE	NULL
+#endif
+
+static struct uart_driver msm_uart_driver = {
+	.owner		= THIS_MODULE,
+	.driver_name	= "msm_serial",
+	.dev_name	= "ttyMSM",
+	.nr		= UART_NR,
+	.cons		= MSM_CONSOLE,
+};
+
+static int __init msm_serial_probe(struct platform_device *pdev)
+{
+	struct msm_port *msm_port;
+	struct resource *resource;
+	struct uart_port *port;
+
+	if (pdev->id < 0 || pdev->id >= UART_NR)
+		return -ENXIO;
+
+	port = get_port_from_line(pdev->id);
+	port->dev = &pdev->dev;
+	msm_port = to_msm_uart(port);
+
+	msm_port->clk = clk_get(&pdev->dev, "uart_clk");
+	if (IS_ERR(msm_port->clk))
+		return PTR_ERR(msm_port->clk);
+	port->uartclk = clk_get_rate(msm_port->clk);
+
+	resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!resource)
+		return -ENXIO;
+	port->mapbase = resource->start;
+
+	port->irq = platform_get_irq(pdev, 0);
+	if (port->irq < 0)
+		return -ENXIO;
+
+	platform_set_drvdata(pdev, port);
+
+	return uart_add_one_port(&msm_uart_driver, port);
+}
+
+static int __exit msm_serial_remove(struct platform_device *pdev)
+{
+	struct msm_port *msm_port = platform_get_drvdata(pdev);
+
+	clk_put(msm_port->clk);
+
+	return 0;
+}
+
+static struct platform_driver msm_platform_driver = {
+	.probe = msm_serial_probe,
+	.remove = __exit_p(msm_serial_remove),
+	.driver = {
+		.name = "msm_serial",
+		.owner = THIS_MODULE,
+	},
+};
+
+static int __init msm_serial_init(void)
+{
+	int ret;
+
+	ret = uart_register_driver(&msm_uart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_probe(&msm_platform_driver, msm_serial_probe);
+	if (ret)
+		uart_unregister_driver(&msm_uart_driver);
+
+	return ret;
+}
+
+static void __exit msm_serial_exit(void)
+{
+#ifdef CONFIG_SERIAL_MSM_CONSOLE
+	unregister_console(&msm_console);
+#endif
+	platform_driver_unregister(&msm_platform_driver);
+	uart_unregister_driver(&msm_uart_driver);
+}
+
+module_init(msm_serial_init);
+module_exit(msm_serial_exit);
+
+MODULE_AUTHOR("Robert Love <rlove@google.com>");
+MODULE_DESCRIPTION("Driver for msm7x serial device");
+MODULE_LICENSE("GPL");
diff --git a/drivers/serial/msm_serial.h b/drivers/serial/msm_serial.h
new file mode 100644
index 0000000..689f1fa
--- /dev/null
+++ b/drivers/serial/msm_serial.h
@@ -0,0 +1,117 @@
+/*
+ * drivers/serial/msm_serial.h
+ *
+ * Copyright (C) 2007 Google, Inc.
+ * Author: Robert Love <rlove@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __DRIVERS_SERIAL_MSM_SERIAL_H
+#define __DRIVERS_SERIAL_MSM_SERIAL_H
+
+#define UART_MR1			0x0000
+
+#define UART_MR1_AUTO_RFR_LEVEL0	0x3F
+#define UART_MR1_AUTO_RFR_LEVEL1	0x3FF00
+#define UART_MR1_RX_RDY_CTL    		(1 << 7)
+#define UART_MR1_CTS_CTL       		(1 << 6)
+
+#define UART_MR2			0x0004
+#define UART_MR2_ERROR_MODE		(1 << 6)
+#define UART_MR2_BITS_PER_CHAR		0x30
+#define UART_MR2_BITS_PER_CHAR_5	(0x0 << 4)
+#define UART_MR2_BITS_PER_CHAR_6	(0x1 << 4)
+#define UART_MR2_BITS_PER_CHAR_7	(0x2 << 4)
+#define UART_MR2_BITS_PER_CHAR_8	(0x3 << 4)
+#define UART_MR2_STOP_BIT_LEN_ONE	(0x1 << 2)
+#define UART_MR2_STOP_BIT_LEN_TWO	(0x3 << 2)
+#define UART_MR2_PARITY_MODE_NONE	0x0
+#define UART_MR2_PARITY_MODE_ODD	0x1
+#define UART_MR2_PARITY_MODE_EVEN	0x2
+#define UART_MR2_PARITY_MODE_SPACE	0x3
+#define UART_MR2_PARITY_MODE		0x3
+
+#define UART_CSR	0x0008
+#define UART_CSR_115200	0xFF
+#define UART_CSR_57600	0xEE
+#define UART_CSR_38400	0xDD
+#define UART_CSR_28800	0xCC
+#define UART_CSR_19200	0xBB
+#define UART_CSR_14400	0xAA
+#define UART_CSR_9600	0x99
+#define UART_CSR_4800	0x77
+#define UART_CSR_2400	0x55
+#define UART_CSR_1200	0x44
+#define UART_CSR_600	0x33
+#define UART_CSR_300	0x22
+
+#define UART_TF		0x000C
+
+#define UART_CR				0x0010
+#define UART_CR_CMD_NULL		(0 << 4)
+#define UART_CR_CMD_RESET_RX		(1 << 4)
+#define UART_CR_CMD_RESET_TX		(2 << 4)
+#define UART_CR_CMD_RESET_ERR		(3 << 4)
+#define UART_CR_CMD_RESET_BREAK_INT	(4 << 4)
+#define UART_CR_CMD_START_BREAK		(5 << 4)
+#define UART_CR_CMD_STOP_BREAK		(6 << 4)
+#define UART_CR_CMD_RESET_CTS		(7 << 4)
+#define UART_CR_CMD_PACKET_MODE		(9 << 4)
+#define UART_CR_CMD_MODE_RESET		(12 << 4)
+#define UART_CR_CMD_SET_RFR		(13 << 4)
+#define UART_CR_CMD_RESET_RFR		(14 << 4)
+#define UART_CR_TX_DISABLE		(1 << 3)
+#define UART_CR_TX_ENABLE		(1 << 3)
+#define UART_CR_RX_DISABLE		(1 << 3)
+#define UART_CR_RX_ENABLE		(1 << 3)
+
+#define UART_IMR		0x0014
+#define UART_IMR_TXLEV		(1 << 0)
+#define UART_IMR_RXSTALE	(1 << 3)
+#define UART_IMR_RXLEV		(1 << 4)
+#define UART_IMR_DELTA_CTS	(1 << 5)
+#define UART_IMR_CURRENT_CTS	(1 << 6)
+
+#define UART_IPR_RXSTALE_LAST		0x20
+#define UART_IPR_STALE_LSB		0x1F
+#define UART_IPR_STALE_TIMEOUT_MSB	0x3FF80
+
+#define UART_IPR	0x0018
+#define UART_TFWR	0x001C
+#define UART_RFWR	0x0020
+#define UART_HCR	0x0024
+
+#define UART_MREG		0x0028
+#define UART_NREG		0x002C
+#define UART_DREG		0x0030
+#define UART_MNDREG		0x0034
+#define UART_IRDA		0x0038
+#define UART_MISR_MODE		0x0040
+#define UART_MISR_RESET		0x0044
+#define UART_MISR_EXPORT	0x0048
+#define UART_MISR_VAL		0x004C
+#define UART_TEST_CTRL		0x0050
+
+#define UART_SR			0x0008
+#define UART_SR_HUNT_CHAR	(1 << 7)
+#define UART_SR_RX_BREAK	(1 << 6)
+#define UART_SR_PAR_FRAME_ERR	(1 << 5)
+#define UART_SR_OVERRUN		(1 << 4)
+#define UART_SR_TX_EMPTY	(1 << 3)
+#define UART_SR_TX_READY	(1 << 2)
+#define UART_SR_RX_FULL		(1 << 1)
+#define UART_SR_RX_READY	(1 << 0)
+
+#define UART_RF		0x000C
+#define UART_MISR	0x0010
+#define UART_ISR	0x0014
+
+#endif	/* __DRIVERS_SERIAL_MSM_SERIAL_H */
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 6fd80c4..23d2fb0 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -171,6 +171,9 @@
 /* Timberdale UART */
 #define PORT_TIMBUART	87
 
+/* Qualcomm MSM SoCs */
+#define PORT_MSM	88
+
 #ifdef __KERNEL__
 
 #include <linux/compiler.h>
-- 
1.6.2.4

[PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Brian Swetland]

Provides options to select one of the three "lowspeed" UARTs
on MSM7k SoCs for DEBUG_LL output from the zImage decompressor
and kernel.

Signed-off-by: Brian Swetland <swetland@google.com>
---
 arch/arm/mach-msm/Kconfig                    |   24 ++++++++++++++++++++++++
 arch/arm/mach-msm/include/mach/debug-macro.S |   24 +++++++++++++++++-------
 arch/arm/mach-msm/include/mach/msm_iomap.h   |   12 ++++++++++++
 arch/arm/mach-msm/include/mach/uncompress.h  |    7 +++++++
 arch/arm/mach-msm/io.c                       |    3 +++
 5 files changed, 63 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
index d140abc..35f2a90 100644
--- a/arch/arm/mach-msm/Kconfig
+++ b/arch/arm/mach-msm/Kconfig
@@ -3,6 +3,30 @@ if ARCH_MSM
 comment "MSM Board Type"
 	depends on ARCH_MSM
 
+config MSM_DEBUG_UART
+	int
+	default 1 if MSM_DEBUG_UART1
+	default 2 if MSM_DEBUG_UART2
+	default 3 if MSM_DEBUG_UART3
+
+choice
+	prompt "Debug UART"
+
+	default MSM_DEBUG_UART_NONE
+
+	config MSM_DEBUG_UART_NONE
+		bool "None"
+
+	config MSM_DEBUG_UART1
+		bool "UART1"
+
+	config MSM_DEBUG_UART2
+		bool "UART2"
+
+	config MSM_DEBUG_UART3
+		bool "UART3"
+endchoice
+
 config MACH_HALIBUT
 	depends on ARCH_MSM
 	default y
diff --git a/arch/arm/mach-msm/include/mach/debug-macro.S b/arch/arm/mach-msm/include/mach/debug-macro.S
index 1db3c97..d48747e 100644
--- a/arch/arm/mach-msm/include/mach/debug-macro.S
+++ b/arch/arm/mach-msm/include/mach/debug-macro.S
@@ -14,15 +14,18 @@
  *
  */
 
+
+
 #include <mach/hardware.h>
 #include <mach/msm_iomap.h>
 
+#ifdef CONFIG_MSM_DEBUG_UART
 	.macro	addruart,rx
 	@ see if the MMU is enabled and select appropriate base address
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1
-	ldreq	\rx, =MSM_UART1_PHYS
-	movne	\rx, #0
+	ldreq	\rx, =MSM_DEBUG_UART_PHYS
+	ldrne	\rx, =MSM_DEBUG_UART_BASE
 	.endm
 
 	.macro	senduart,rd,rx
@@ -32,13 +35,20 @@
 
 	.macro	waituart,rd,rx
 	@ wait for TX_READY
-	teq	\rx, #0
-	bne	2f
-1:	ldr	\rd, [\rx, #0x08]
+1001:	ldr	\rd, [\rx, #0x08]
 	tst	\rd, #0x04
-	beq	1b
-2:
+	beq	1001b
+	.endm
+#else
+	.macro	addruart,rx
+	.endm
+
+	.macro	senduart,rd,rx
+	.endm
+
+	.macro	waituart,rd,rx
 	.endm
+#endif
 
 	.macro	busyuart,rd,rx
 	.endm
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h
index 2f7b4c8..9dae1a9 100644
--- a/arch/arm/mach-msm/include/mach/msm_iomap.h
+++ b/arch/arm/mach-msm/include/mach/msm_iomap.h
@@ -84,6 +84,18 @@
 #define MSM_UART3_PHYS        0xA9C00000
 #define MSM_UART3_SIZE        SZ_4K
 
+#ifdef CONFIG_MSM_DEBUG_UART
+#define MSM_DEBUG_UART_BASE   0xE1000000
+#if CONFIG_MSM_DEBUG_UART == 1
+#define MSM_DEBUG_UART_PHYS   MSM_UART1_PHYS
+#elif CONFIG_MSM_DEBUG_UART == 2
+#define MSM_DEBUG_UART_PHYS   MSM_UART2_PHYS
+#elif CONFIG_MSM_DEBUG_UART == 3
+#define MSM_DEBUG_UART_PHYS   MSM_UART3_PHYS
+#endif
+#define MSM_DEBUG_UART_SIZE   SZ_4K
+#endif
+
 #define MSM_SDC1_PHYS         0xA0400000
 #define MSM_SDC1_SIZE         SZ_4K
 
diff --git a/arch/arm/mach-msm/include/mach/uncompress.h b/arch/arm/mach-msm/include/mach/uncompress.h
index 026e895..d94292c 100644
--- a/arch/arm/mach-msm/include/mach/uncompress.h
+++ b/arch/arm/mach-msm/include/mach/uncompress.h
@@ -16,9 +16,16 @@
 #ifndef __ASM_ARCH_MSM_UNCOMPRESS_H
 
 #include "hardware.h"
+#include "linux/io.h"
+#include "mach/msm_iomap.h"
 
 static void putc(int c)
 {
+#if defined(MSM_DEBUG_UART_PHYS)
+	unsigned base = MSM_DEBUG_UART_PHYS;
+	while (!(readl(base + 0x08) & 0x04)) ;
+	writel(c, base + 0x0c);
+#endif
 }
 
 static inline void flush(void)
diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
index 6e7692f..1c5e7da 100644
--- a/arch/arm/mach-msm/io.c
+++ b/arch/arm/mach-msm/io.c
@@ -42,6 +42,9 @@ static struct map_desc msm_io_desc[] __initdata = {
 	MSM_DEVICE(GPIO1),
 	MSM_DEVICE(GPIO2),
 	MSM_DEVICE(CLK_CTL),
+#ifdef CONFIG_MSM_DEBUG_UART
+	MSM_DEVICE(DEBUG_UART),
+#endif
 	{
 		.virtual =  (unsigned long) MSM_SHARED_RAM_BASE,
 		.pfn =      __phys_to_pfn(MSM_SHARED_RAM_PHYS),
-- 
1.6.2.4

[PATCH 3/3] [ARM] msm: add minimal board file for HTC Dream device

[Brian Swetland]

This is just enough to get the device booting and serial console
working.  Sufficient for debugging further MSM7k/Dream Support.
This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
are all the same hardware, known as "trout" to the ARM machine
database).

Signed-off-by: Brian Swetland <swetland@google.com>
---
 arch/arm/mach-msm/Kconfig       |    6 +++
 arch/arm/mach-msm/Makefile      |    1 +
 arch/arm/mach-msm/board-dream.c |   84 +++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-msm/board-dream.h |    5 ++
 4 files changed, 96 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-msm/board-dream.c
 create mode 100644 arch/arm/mach-msm/board-dream.h

diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
index 35f2a90..f780086 100644
--- a/arch/arm/mach-msm/Kconfig
+++ b/arch/arm/mach-msm/Kconfig
@@ -34,4 +34,10 @@ config MACH_HALIBUT
 	help
 	  Support for the Qualcomm SURF7201A eval board.
 
+config MACH_TROUT
+	default y
+	bool "HTC Dream (aka trout)"
+	help
+	  Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
+
 endif
diff --git a/arch/arm/mach-msm/Makefile b/arch/arm/mach-msm/Makefile
index 1aa4700..91e6f5c 100644
--- a/arch/arm/mach-msm/Makefile
+++ b/arch/arm/mach-msm/Makefile
@@ -6,3 +6,4 @@ obj-y += clock.o clock-7x01a.o
 
 obj-$(CONFIG_MACH_HALIBUT) += board-halibut.o
 
+obj-$(CONFIG_MACH_TROUT) += board-dream.o
diff --git a/arch/arm/mach-msm/board-dream.c b/arch/arm/mach-msm/board-dream.c
new file mode 100644
index 0000000..6eae7e3
--- /dev/null
+++ b/arch/arm/mach-msm/board-dream.c
@@ -0,0 +1,84 @@
+/* linux/arch/arm/mach-msm/board-dream.c
+ *
+ * Copyright (C) 2009 Google, Inc.
+ * Author: Brian Swetland <swetland@google.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/board.h>
+#include <mach/hardware.h>
+#include <mach/msm_iomap.h>
+
+#include "devices.h"
+#include "board-dream.h"
+
+static struct platform_device *devices[] __initdata = {
+	&msm_device_uart3,
+	&msm_device_smd,
+	&msm_device_nand,
+	&msm_device_hsusb,
+	&msm_device_i2c,
+};
+
+extern struct sys_timer msm_timer;
+
+static void __init trout_init_irq(void)
+{
+	msm_init_irq();
+}
+
+static void __init trout_init(void)
+{
+	platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
+static struct map_desc trout_io_desc[] __initdata = {
+	{
+		.virtual = TROUT_CPLD_BASE,
+		.pfn     = __phys_to_pfn(TROUT_CPLD_START),
+		.length  = TROUT_CPLD_SIZE,
+		.type    = MT_DEVICE_NONSHARED
+	}
+};
+
+static void __init trout_map_io(void)
+{
+	msm_map_common_io();
+	iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
+
+#ifdef CONFIG_MSM_DEBUG_UART3
+	/* route UART3 to the "H2W" extended usb connector */
+	writeb(0x80, TROUT_CPLD_BASE + 0x00);
+#endif
+
+	msm_clock_init();
+}
+
+MACHINE_START(TROUT, "HTC Dream")
+#ifdef CONFIG_MSM_DEBUG_UART
+	.phys_io	= MSM_DEBUG_UART_PHYS,
+	.io_pg_offst	= ((MSM_DEBUG_UART_BASE) >> 18) & 0xfffc,
+#endif
+	.boot_params	= 0x10000100,
+	.map_io		= trout_map_io,
+	.init_irq	= trout_init_irq,
+	.init_machine	= trout_init,
+	.timer		= &msm_timer,
+MACHINE_END
diff --git a/arch/arm/mach-msm/board-dream.h b/arch/arm/mach-msm/board-dream.h
new file mode 100644
index 0000000..4f345a5
--- /dev/null
+++ b/arch/arm/mach-msm/board-dream.h
@@ -0,0 +1,5 @@
+
+#define TROUT_CPLD_BASE   0xE8100000
+#define TROUT_CPLD_START  0x98000000
+#define TROUT_CPLD_SIZE   SZ_4K
+
-- 
1.6.2.4

Re: [PATCH 3/3] [ARM] msm: add minimal board file for HTC Dream device

[GeunSik Lim]

On Thu, Jun 18, 2009 at 9:31 AM, Brian Swetland<swetland@google.com> wrote:
> This is just enough to get the device booting and serial console
> working.  Sufficient for debugging further MSM7k/Dream Support.
> This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
> are all the same hardware, known as "trout" to the ARM machine
> database).
Hi Brian,
I have one silly question.
I still not understand "trout" meaning with your description.

> +config MACH_TROUT
> +       default y
> +       bool "HTC Dream (aka trout)"
> +       help
> +         Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
> +
"trout" word just means HTC Dream Model. Is it right?
Thks,

-- 
Regards,
GeunSik Lim ( Samsung Electronics )
Blog : http://blog.naver.com/invain/
e-Mail: geunsik.lim@samsung.com
           leemgs@gmail.com , leemgs1@gmail.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Re: [PATCH 3/3] [ARM] msm: add minimal board file for HTC Dream device

[Brian Swetland]

On Wed, Jun 17, 2009 at 6:56 PM, GeunSik Lim<leemgs1@gmail.com> wrote:
> On Thu, Jun 18, 2009 at 9:31 AM, Brian Swetland<swetland@google.com> wrote:
>> This is just enough to get the device booting and serial console
>> working.  Sufficient for debugging further MSM7k/Dream Support.
>> This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
>> are all the same hardware, known as "trout" to the ARM machine
>> database).
> Hi Brian,
> I have one silly question.
> I still not understand "trout" meaning with your description.
>
>> +config MACH_TROUT
>> +       default y
>> +       bool "HTC Dream (aka trout)"
>> +       help
>> +         Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
>> +
> "trout" word just means HTC Dream Model. Is it right?

Yes -- this is the ARM linux kernel machine ID for this hardware:
http://www.arm.linux.org.uk/developer/machines/list.php?id=1440

Brian

Re: [PATCH 1/3] [ARM] msm_serial: serial driver for MSM7K onboard serial peripheral.

[Alan Cox]

On Wed, 17 Jun 2009 17:31:13 -0700
Brian Swetland <swetland@google.com> wrote:

> From: Robert Love <rlove@google.com>
> 
> Provides support for the "lowspeed" UARTs on the MSM7k and QSD8k
> family of SoCs from Qualcomm.  Serial console support included.
> 
> Signed-off-by: Robert Love <rlove@google.com>
> Signed-off-by: Brian Swetland <swetland@google.com>
> Acked-by: Pavel Machek <pavel@ucw.cz>

If you fold other peoples patches into something please preserve the
authorship data and preferably keep the two patches separated as it
otherwise causes merge problems if stuff (eg the serial patches) goes via
two trees at once.

At the moment the ttydev tree has
	-> your original -> my (intel's I guess) fixes ->

and if the updated one also went in via the arm tree git can't always
figure out what is going on.

If its only going by one path and you know that then just adding an
additional note on the authorship of updates is fine but this being
serial/tty and ARM is likely to hit both trees.

Alan

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Pavel Machek]

On Wed 2009-06-17 17:31:14, Brian Swetland wrote:
> Provides options to select one of the three "lowspeed" UARTs
> on MSM7k SoCs for DEBUG_LL output from the zImage decompressor
> and kernel.
> 
> Signed-off-by: Brian Swetland <swetland@google.com>

Acked-by: Pavel Machek <pavel@ucw.cz>

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Re: [PATCH 3/3] [ARM] msm: add minimal board file for HTC Dream device

[Pavel Machek]

On Wed 2009-06-17 17:31:15, Brian Swetland wrote:
> This is just enough to get the device booting and serial console
> working.  Sufficient for debugging further MSM7k/Dream Support.
> This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
> are all the same hardware, known as "trout" to the ARM machine
> database).
> 
> Signed-off-by: Brian Swetland <swetland@google.com>

Acked-by: Pavel Machek <pavel@ucw.cz>

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Re: [PATCH 3/3] [ARM] msm: add minimal board file for HTC Dream device

[GeunSik Lim]

On Thu, Jun 18, 2009 at 11:44 AM, Brian Swetland<swetland@google.com> wrote:
> On Wed, Jun 17, 2009 at 6:56 PM, GeunSik Lim<leemgs1@gmail.com> wrote:
>> On Thu, Jun 18, 2009 at 9:31 AM, Brian Swetland<swetland@google.com> wrote:
>>> This is just enough to get the device booting and serial console
>>> working.  Sufficient for debugging further MSM7k/Dream Support.
>>> This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
>>> are all the same hardware, known as "trout" to the ARM machine
>>> database).
>> Hi Brian,
>> I have one silly question.
>> I still not understand "trout" meaning with your description.
>>
>>> +config MACH_TROUT
>>> +       default y
>>> +       bool "HTC Dream (aka trout)"
>>> +       help
>>> +         Support for the HTC Dream, T-Mobile G1, Android ADP1 devices.
>>> +
>> "trout" word just means HTC Dream Model. Is it right?
>
> Yes -- this is the ARM linux kernel machine ID for this hardware:
> http://www.arm.linux.org.uk/developer/machines/list.php?id=1440
>
> Brian
>
Looks good to me.
Reviewed-by: GeunSik Lim <geunsik.lim@samsung.com>


-- 
Regards,
GeunSik Lim ( Samsung Electronics )
Blog : http://blog.naver.com/invain/
e-Mail: geunsik.lim@samsung.com
           leemgs@gmail.com , leemgs1@gmail.com
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Re: [PATCH 1/3] [ARM] msm_serial: serial driver for MSM7K onboard serial peripheral.

[Brian Swetland]

On Thu, Jun 18, 2009 at 2:20 AM, Alan Cox<alan@lxorguk.ukuu.org.uk> wrote:
> On Wed, 17 Jun 2009 17:31:13 -0700
> Brian Swetland <swetland@google.com> wrote:
>
>> From: Robert Love <rlove@google.com>
>>
>> Provides support for the "lowspeed" UARTs on the MSM7k and QSD8k
>> family of SoCs from Qualcomm.  Serial console support included.
>>
>> Signed-off-by: Robert Love <rlove@google.com>
>> Signed-off-by: Brian Swetland <swetland@google.com>
>> Acked-by: Pavel Machek <pavel@ucw.cz>
>
> If you fold other peoples patches into something please preserve the
> authorship data and preferably keep the two patches separated as it
> otherwise causes merge problems if stuff (eg the serial patches) goes via
> two trees at once.

Ah, sorry about that -- I can resend the revised patch that your patch
applies against (but without your changes merged in).  Previously, for
the ARM stuff I got the impression that a single patch folding small
changes in was preferred, but I may have misunderstood the workflow.

> At the moment the ttydev tree has
>        -> your original -> my (intel's I guess) fixes ->
>
> and if the updated one also went in via the arm tree git can't always
> figure out what is going on.
>
> If its only going by one path and you know that then just adding an
> additional note on the authorship of updates is fine but this being
> serial/tty and ARM is likely to hit both trees.
>
> Alan
>

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Pavel Machek]

On Mon 2009-06-15 11:43:23, Brian Swetland wrote:
> On Mon, Jun 15, 2009 at 11:34 AM, Pavel Machek<pavel@ucw.cz> wrote:
> >> > ...and those that do, have it at fixed uart, no?
> >>
> >> Well, I'd like to support the SoC generally, not just Dream -- it's
> >> used in a bunch of different devices, and there's nothing that forces
> >> you to use UART3 everywhere (I certainly have seen some 7k hardware
> >> that uses UART1 as the debug serial port).
> >
> > Aha, ok, I guess that should go to the changelog. (Nice bonus would be
> > if it was automatically/correctly set up when user selects machine
> > type... Actually, how does that work if you support few boards with
> > same kernel...?)
> 
> At this point a kernel for multiple boards with different DEBUG_LL
> uarts doesn't work correctly -- I'm not sure this could be done
> without making the debug macro code, etc, a lot messier (since it has
> to write to the physical uart address in early boot and I believe that
> happens before the machine type is determined, though maybe I'm
> wrong).

Ok, makes sense.
									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Brian Swetland]

On Mon, Jun 15, 2009 at 11:34 AM, Pavel Machek<pavel@ucw.cz> wrote:
>> > ...and those that do, have it at fixed uart, no?
>>
>> Well, I'd like to support the SoC generally, not just Dream -- it's
>> used in a bunch of different devices, and there's nothing that forces
>> you to use UART3 everywhere (I certainly have seen some 7k hardware
>> that uses UART1 as the debug serial port).
>
> Aha, ok, I guess that should go to the changelog. (Nice bonus would be
> if it was automatically/correctly set up when user selects machine
> type... Actually, how does that work if you support few boards with
> same kernel...?)

At this point a kernel for multiple boards with different DEBUG_LL
uarts doesn't work correctly -- I'm not sure this could be done
without making the debug macro code, etc, a lot messier (since it has
to write to the physical uart address in early boot and I believe that
happens before the machine type is determined, though maybe I'm
wrong).

For a shipping kernel that's just including the serial driver and not
the DEBUG_LL stuff, it doesn't have a problem (since the uart is
configured from the board file a bit later in boot).

Brian

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Pavel Machek]

On Mon 2009-06-15 11:30:11, Brian Swetland wrote:
> On Mon, Jun 15, 2009 at 6:20 AM, Pavel Machek<pavel@ucw.cz> wrote:
> > Hi!
> >
> >> Signed-off-by: Brian Swetland <swetland@google.com>
> >> ---
> >>  arch/arm/mach-msm/Kconfig                    |   24 ++++++++++++++++++++++++
> >>  arch/arm/mach-msm/include/mach/debug-macro.S |   25 ++++++++++++++++++-------
> >>  arch/arm/mach-msm/include/mach/msm_iomap.h   |   12 ++++++++++++
> >>  arch/arm/mach-msm/include/mach/uncompress.h  |    7 +++++++
> >>  arch/arm/mach-msm/io.c                       |    3 +++
> >>  5 files changed, 64 insertions(+), 7 deletions(-)
> >
> > I'm not sure if this is appropriate for mainline at this point. It
> > seems like few people have debug cable at this point...
> >
> >> +config MSM_DEBUG_UART
> >> +     int
> >> +     default 1 if MSM_DEBUG_UART1
> >> +     default 2 if MSM_DEBUG_UART2
> >> +     default 3 if MSM_DEBUG_UART3
> >
> > ...and those that do, have it at fixed uart, no?
> 
> Well, I'd like to support the SoC generally, not just Dream -- it's
> used in a bunch of different devices, and there's nothing that forces
> you to use UART3 everywhere (I certainly have seen some 7k hardware
> that uses UART1 as the debug serial port).

Aha, ok, I guess that should go to the changelog. (Nice bonus would be
if it was automatically/correctly set up when user selects machine
type... Actually, how does that work if you support few boards with
same kernel...?)



									Pavel
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Brian Swetland]

On Mon, Jun 15, 2009 at 6:20 AM, Pavel Machek<pavel@ucw.cz> wrote:
> Hi!
>
>> Signed-off-by: Brian Swetland <swetland@google.com>
>> ---
>>  arch/arm/mach-msm/Kconfig                    |   24 ++++++++++++++++++++++++
>>  arch/arm/mach-msm/include/mach/debug-macro.S |   25 ++++++++++++++++++-------
>>  arch/arm/mach-msm/include/mach/msm_iomap.h   |   12 ++++++++++++
>>  arch/arm/mach-msm/include/mach/uncompress.h  |    7 +++++++
>>  arch/arm/mach-msm/io.c                       |    3 +++
>>  5 files changed, 64 insertions(+), 7 deletions(-)
>
> I'm not sure if this is appropriate for mainline at this point. It
> seems like few people have debug cable at this point...
>
>> +config MSM_DEBUG_UART
>> +     int
>> +     default 1 if MSM_DEBUG_UART1
>> +     default 2 if MSM_DEBUG_UART2
>> +     default 3 if MSM_DEBUG_UART3
>
> ...and those that do, have it at fixed uart, no?

Well, I'd like to support the SoC generally, not just Dream -- it's
used in a bunch of different devices, and there's nothing that forces
you to use UART3 everywhere (I certainly have seen some 7k hardware
that uses UART1 as the debug serial port).

Brian

Re: [PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Pavel Machek]

Hi!

> Signed-off-by: Brian Swetland <swetland@google.com>
> ---
>  arch/arm/mach-msm/Kconfig                    |   24 ++++++++++++++++++++++++
>  arch/arm/mach-msm/include/mach/debug-macro.S |   25 ++++++++++++++++++-------
>  arch/arm/mach-msm/include/mach/msm_iomap.h   |   12 ++++++++++++
>  arch/arm/mach-msm/include/mach/uncompress.h  |    7 +++++++
>  arch/arm/mach-msm/io.c                       |    3 +++
>  5 files changed, 64 insertions(+), 7 deletions(-)

I'm not sure if this is appropriate for mainline at this point. It
seems like few people have debug cable at this point...

> +config MSM_DEBUG_UART
> +	int
> +	default 1 if MSM_DEBUG_UART1
> +	default 2 if MSM_DEBUG_UART2
> +	default 3 if MSM_DEBUG_UART3

...and those that do, have it at fixed uart, no? 

> index 1db3c97..ab772cc 100644
> --- a/arch/arm/mach-msm/include/mach/debug-macro.S
> +++ b/arch/arm/mach-msm/include/mach/debug-macro.S
> @@ -14,15 +14,18 @@
>   *
>   */
>  
> +
> +
>  #include <mach/hardware.h>
>  #include <mach/msm_iomap.h>

It has enough lines, already...

> +#ifdef CONFIG_MSM_DEBUG_UART
>  	.macro	addruart,rx
>  	@ see if the MMU is enabled and select appropriate base address
>  	mrc	p15, 0, \rx, c1, c0
>  	tst	\rx, #1
> -	ldreq	\rx, =MSM_UART1_PHYS
> -	movne	\rx, #0
> +	ldreq	\rx, =MSM_DEBUG_UART_PHYS
> +	ldrne	\rx, =MSM_DEBUG_UART_BASE
>  	.endm
>  
>  	.macro	senduart,rd,rx
> @@ -32,13 +35,21 @@
>  
>  	.macro	waituart,rd,rx
>  	@ wait for TX_READY
> -	teq	\rx, #0
> -	bne	2f
> -1:	ldr	\rd, [\rx, #0x08]
> +1001:	ldr	\rd, [\rx, #0x08]
>  	tst	\rd, #0x04
> -	beq	1b
> -2:
> +	beq	1001b
> +1002:
> +	.endm

Is the 1002 label required?

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

[PATCH 2/3] [ARM] msm: make debugging UART (for DEBUG_LL) configurable

[Brian Swetland]

Signed-off-by: Brian Swetland <swetland@google.com>
---
 arch/arm/mach-msm/Kconfig                    |   24 ++++++++++++++++++++++++
 arch/arm/mach-msm/include/mach/debug-macro.S |   25 ++++++++++++++++++-------
 arch/arm/mach-msm/include/mach/msm_iomap.h   |   12 ++++++++++++
 arch/arm/mach-msm/include/mach/uncompress.h  |    7 +++++++
 arch/arm/mach-msm/io.c                       |    3 +++
 5 files changed, 64 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig
index d140abc..35f2a90 100644
--- a/arch/arm/mach-msm/Kconfig
+++ b/arch/arm/mach-msm/Kconfig
@@ -3,6 +3,30 @@ if ARCH_MSM
 comment "MSM Board Type"
 	depends on ARCH_MSM
 
+config MSM_DEBUG_UART
+	int
+	default 1 if MSM_DEBUG_UART1
+	default 2 if MSM_DEBUG_UART2
+	default 3 if MSM_DEBUG_UART3
+
+choice
+	prompt "Debug UART"
+
+	default MSM_DEBUG_UART_NONE
+
+	config MSM_DEBUG_UART_NONE
+		bool "None"
+
+	config MSM_DEBUG_UART1
+		bool "UART1"
+
+	config MSM_DEBUG_UART2
+		bool "UART2"
+
+	config MSM_DEBUG_UART3
+		bool "UART3"
+endchoice
+
 config MACH_HALIBUT
 	depends on ARCH_MSM
 	default y
diff --git a/arch/arm/mach-msm/include/mach/debug-macro.S b/arch/arm/mach-msm/include/mach/debug-macro.S
index 1db3c97..ab772cc 100644
--- a/arch/arm/mach-msm/include/mach/debug-macro.S
+++ b/arch/arm/mach-msm/include/mach/debug-macro.S
@@ -14,15 +14,18 @@
  *
  */
 
+
+
 #include <mach/hardware.h>
 #include <mach/msm_iomap.h>
 
+#ifdef CONFIG_MSM_DEBUG_UART
 	.macro	addruart,rx
 	@ see if the MMU is enabled and select appropriate base address
 	mrc	p15, 0, \rx, c1, c0
 	tst	\rx, #1
-	ldreq	\rx, =MSM_UART1_PHYS
-	movne	\rx, #0
+	ldreq	\rx, =MSM_DEBUG_UART_PHYS
+	ldrne	\rx, =MSM_DEBUG_UART_BASE
 	.endm
 
 	.macro	senduart,rd,rx
@@ -32,13 +35,21 @@
 
 	.macro	waituart,rd,rx
 	@ wait for TX_READY
-	teq	\rx, #0
-	bne	2f
-1:	ldr	\rd, [\rx, #0x08]
+1001:	ldr	\rd, [\rx, #0x08]
 	tst	\rd, #0x04
-	beq	1b
-2:
+	beq	1001b
+1002:
+	.endm
+#else
+	.macro	addruart,rx
+	.endm
+
+	.macro	senduart,rd,rx
+	.endm
+
+	.macro	waituart,rd,rx
 	.endm
+#endif
 
 	.macro	busyuart,rd,rx
 	.endm
diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h
index 2f7b4c8..9dae1a9 100644
--- a/arch/arm/mach-msm/include/mach/msm_iomap.h
+++ b/arch/arm/mach-msm/include/mach/msm_iomap.h
@@ -84,6 +84,18 @@
 #define MSM_UART3_PHYS        0xA9C00000
 #define MSM_UART3_SIZE        SZ_4K
 
+#ifdef CONFIG_MSM_DEBUG_UART
+#define MSM_DEBUG_UART_BASE   0xE1000000
+#if CONFIG_MSM_DEBUG_UART == 1
+#define MSM_DEBUG_UART_PHYS   MSM_UART1_PHYS
+#elif CONFIG_MSM_DEBUG_UART == 2
+#define MSM_DEBUG_UART_PHYS   MSM_UART2_PHYS
+#elif CONFIG_MSM_DEBUG_UART == 3
+#define MSM_DEBUG_UART_PHYS   MSM_UART3_PHYS
+#endif
+#define MSM_DEBUG_UART_SIZE   SZ_4K
+#endif
+
 #define MSM_SDC1_PHYS         0xA0400000
 #define MSM_SDC1_SIZE         SZ_4K
 
diff --git a/arch/arm/mach-msm/include/mach/uncompress.h b/arch/arm/mach-msm/include/mach/uncompress.h
index 026e895..d94292c 100644
--- a/arch/arm/mach-msm/include/mach/uncompress.h
+++ b/arch/arm/mach-msm/include/mach/uncompress.h
@@ -16,9 +16,16 @@
 #ifndef __ASM_ARCH_MSM_UNCOMPRESS_H
 
 #include "hardware.h"
+#include "linux/io.h"
+#include "mach/msm_iomap.h"
 
 static void putc(int c)
 {
+#if defined(MSM_DEBUG_UART_PHYS)
+	unsigned base = MSM_DEBUG_UART_PHYS;
+	while (!(readl(base + 0x08) & 0x04)) ;
+	writel(c, base + 0x0c);
+#endif
 }
 
 static inline void flush(void)
diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
index 6e7692f..1c5e7da 100644
--- a/arch/arm/mach-msm/io.c
+++ b/arch/arm/mach-msm/io.c
@@ -42,6 +42,9 @@ static struct map_desc msm_io_desc[] __initdata = {
 	MSM_DEVICE(GPIO1),
 	MSM_DEVICE(GPIO2),
 	MSM_DEVICE(CLK_CTL),
+#ifdef CONFIG_MSM_DEBUG_UART
+	MSM_DEVICE(DEBUG_UART),
+#endif
 	{
 		.virtual =  (unsigned long) MSM_SHARED_RAM_BASE,
 		.pfn =      __phys_to_pfn(MSM_SHARED_RAM_PHYS),
-- 
1.6.2.4