[PATCH 00/72] Blackfin updates for 2.6.32

[PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

Minor highlights:
 - shadow console to help with really early kernel output
 - proper decoding of double fault handling

Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.

Barry Song (9):
  Blackfin: bf537-stamp: add resources for AD1938 audio card
  Blackfin: bf538: add bfin_clear_PPI_STATUS() helper
  Blackfin: bf537-stamp: update AD714x resources
  Blackfin: bf537-stamp: drop ATA interrupt probe workaround
  Blackfin: cm-bf527/bf537-stamp: fix dm9000 resources
  Blackfin: bf538-ezkit: add resources for parallel flash
  Blackfin: bf537-stamp: update ad1836 resources
  Blackfin: delete '-spi' suffix in ad1836/ad1938 driver name
  Blackfin: bf538-ezkit: add SPI IRQ resources

Bernd Schmidt (1):
  Blackfin: add ICPLB coverage for async banks

Cliff Cai (1):
  Blackfin: bf533-stamp: fix typo in SPI frequency for ad1836 codec

Graf Yang (5):
  Blackfin: fix MPU handling of invalid memory accesses
  Blackfin: improve double fault debug handling
  Blackfin: SMP port does not yet support cpu frequency scaling
  Blackfin: handle the core timer interrupt with handle_percpu_irq on
    SMP
  Blackfin: swap clocksource ratings for gptimer/cycles

Harald Krapfenbauer (2):
  Blackfin: cm-bf537u: split board from cm-bf537e
  Blackfin: update cm board resources

Ingo Molnar (1):
  Blackfin: Fix link errors with binutils 2.19 and GCC 4.3

Jean Delvare (1):
  Blackfin: clean up duplicate I2C device type definitions

Michael Hennerich (6):
  Blackfin: bf537-stamp: update ADP5588 header name
  Blackfin: rename PCF8574 driver config
  Blackfin: convert boards to use platform data with smc91x
  Blackfin: remove useless duplicated assignment in gpio code
  Blackfin: fix spelling in a few comments
  Blackfin: bf537-stamp: add adp5588 gpio resources

Mike Frysinger (15):
  Blackfin: cleanup traps decode_address() a bit
  Blackfin: convert ptrace to new memory functions
  Blackfin: cleanup printk() usage in module code
  Blackfin: convert malloc()/memset() to zalloc() in module code
  Blackfin: cleanup module section checking
  Blackfin: fix module reloc handling for all memory regions
  Blackfin: push SRAM locks down into related ifdefs
  Blackfin: add support for common FDPIC ptrace requests
  Blackfin: drop unused MMR defines that only cause bad code to be
    written
  Blackfin: fix BF522/BF523 max VCO mixup
  Blackfin: drop board resources for dead devices (pbx/ad9960)
  Blackfin: punt dead cache locking code
  Blackfin: optimize fixed code handling for the most common case
  Blackfin: add some isram-driver self tests
  Blackfin: update ftrace_push_return_trace() breakage

Mingquan Pan (1):
  Blackfin: use KERN_ALERT in all kgdb_test output

Philippe Gerum (10):
  Blackfin: checkpatch --file arch/blackfin/kernel/ipipe.c
  Blackfin: fix misnomer of some I-pipe helpers
  Blackfin: export show_stack() to modules
  Blackfin: allow high priority domains to preempt schedule_tail()
  Blackfin: use generic name for EVT14 handler
  Blackfin: reuse evt_evt14 handler to perform irqtail epilogue
  Blackfin: allow EVT5 to preempt irqtail prologue (CONFIG_DEBUG_HWERR)
  Blackfin: document __ipipe_call_irqtail
  Blackfin: sanitize manual control of IPEND[4]
  Blackfin: inline I-pipe bypass code in ret_from_exception

Robin Getz (7):
  Blackfin: make EVT3->EVT5 lowering more robust wrt IPEND[4]
  Blackfin: reject outdated/unused/wrong relocation types
  Blackfin: clean up early memory setup code
  Blackfin: add an early shadow console
  Blackfin: catch hardware errors earlier during booting
  Blackfin: workaround anomaly 05000283
  Blackfin: fix typo in isram_write()

Roel Kluin (1):
  Blackfin: fix read buffer overflow

Sonic Zhang (3):
  Blackfin: unify duplicated SMP checks in L2 cache kconfig
  Blackfin: do not try displaying the end of the stack
  Blackfin: increase default async timings for parallel flashes

Stefan Pledl (2):
  Blackfin: fix BF548 UART0 DMA IRQ translation
  Blackfin: bf548-ezkit: fix incorrect LCD size parameters

Yi Li (7):
  Blackfin: bf537-stamp: declare SPI IRQ resources
  Blackfin: bf533-stamp: add resources for mmc_spi card
  Blackfin: update anomaly lists
  Blackfin: cleanup sync handling when enabling/disabling cplbs
  Blackfin: do not trace the exception handler
  Blackfin: use raw_smp_processor_id() in exception code
  Blackfin: fix BF54x SPI CS resources

 arch/blackfin/Kconfig                             |   25 +-
 arch/blackfin/Kconfig.debug                       |    6 +
 arch/blackfin/configs/BF518F-EZBRD_defconfig      |    4 +-
 arch/blackfin/configs/BF526-EZBRD_defconfig       |    4 +-
 arch/blackfin/configs/BF527-EZKIT_defconfig       |    4 +-
 arch/blackfin/configs/BF548-EZKIT_defconfig       |    2 +-
 arch/blackfin/include/asm/bfin-global.h           |    6 -
 arch/blackfin/include/asm/bfin5xx_spi.h           |    1 +
 arch/blackfin/include/asm/cplb.h                  |   46 ++-
 arch/blackfin/include/asm/early_printk.h          |   24 +
 arch/blackfin/include/asm/entry.h                 |   30 +-
 arch/blackfin/include/asm/ipipe.h                 |    7 -
 arch/blackfin/include/asm/irq_handler.h           |    1 +
 arch/blackfin/include/asm/mmu_context.h           |    6 +-
 arch/blackfin/include/asm/pda.h                   |    7 +
 arch/blackfin/kernel/Makefile                     |    1 +
 arch/blackfin/kernel/asm-offsets.c                |    7 +
 arch/blackfin/kernel/bfin_dma_5xx.c               |   14 +-
 arch/blackfin/kernel/bfin_gpio.c                  |    1 -
 arch/blackfin/kernel/cplb-mpu/cacheinit.c         |    6 +-
 arch/blackfin/kernel/cplb-mpu/cplbmgr.c           |   63 +--
 arch/blackfin/kernel/cplb-nompu/cacheinit.c       |    6 +-
 arch/blackfin/kernel/cplb-nompu/cplbinit.c        |   11 +-
 arch/blackfin/kernel/cplb-nompu/cplbmgr.c         |   35 +-
 arch/blackfin/kernel/early_printk.c               |   74 ++-
 arch/blackfin/kernel/entry.S                      |   24 +-
 arch/blackfin/kernel/ftrace.c                     |    2 +-
 arch/blackfin/kernel/ipipe.c                      |   83 ++--
 arch/blackfin/kernel/kgdb_test.c                  |    2 +-
 arch/blackfin/kernel/module.c                     |  266 ++++----
 arch/blackfin/kernel/process.c                    |   10 +-
 arch/blackfin/kernel/ptrace.c                     |  155 +++--
 arch/blackfin/kernel/setup.c                      |  120 ++---
 arch/blackfin/kernel/shadow_console.c             |  113 ++++
 arch/blackfin/kernel/time-ts.c                    |    4 +-
 arch/blackfin/kernel/traps.c                      |   88 ++-
 arch/blackfin/kernel/vmlinux.lds.S                |    4 +-
 arch/blackfin/lib/ins.S                           |    4 +-
 arch/blackfin/mach-bf518/boards/ezbrd.c           |   29 +-
 arch/blackfin/mach-bf518/include/mach/anomaly.h   |    1 +
 arch/blackfin/mach-bf518/include/mach/blackfin.h  |   10 -
 arch/blackfin/mach-bf527/boards/cm_bf527.c        |  164 ++---
 arch/blackfin/mach-bf527/boards/ezbrd.c           |   29 +-
 arch/blackfin/mach-bf527/boards/ezkit.c           |   58 +--
 arch/blackfin/mach-bf527/include/mach/anomaly.h   |   13 +-
 arch/blackfin/mach-bf527/include/mach/blackfin.h  |   10 -
 arch/blackfin/mach-bf533/boards/H8606.c           |   39 +-
 arch/blackfin/mach-bf533/boards/blackstamp.c      |   11 +
 arch/blackfin/mach-bf533/boards/cm_bf533.c        |  127 ++++-
 arch/blackfin/mach-bf533/boards/ezkit.c           |   13 +-
 arch/blackfin/mach-bf533/boards/stamp.c           |   83 ++-
 arch/blackfin/mach-bf533/dma.c                    |    8 +-
 arch/blackfin/mach-bf533/include/mach/blackfin.h  |    7 -
 arch/blackfin/mach-bf537/boards/Kconfig           |   12 +-
 arch/blackfin/mach-bf537/boards/Makefile          |    3 +-
 arch/blackfin/mach-bf537/boards/cm_bf537.c        |  638 ------------------
 arch/blackfin/mach-bf537/boards/cm_bf537e.c       |  727 +++++++++++++++++++++
 arch/blackfin/mach-bf537/boards/cm_bf537u.c       |  633 ++++++++++++++++++
 arch/blackfin/mach-bf537/boards/pnav10.c          |   29 +-
 arch/blackfin/mach-bf537/boards/stamp.c           |  249 ++++++--
 arch/blackfin/mach-bf537/boards/tcm_bf537.c       |   43 +-
 arch/blackfin/mach-bf537/dma.c                    |    8 +-
 arch/blackfin/mach-bf537/include/mach/anomaly.h   |    2 +-
 arch/blackfin/mach-bf537/include/mach/blackfin.h  |   90 ---
 arch/blackfin/mach-bf538/boards/ezkit.c           |   65 ++
 arch/blackfin/mach-bf538/include/mach/anomaly.h   |    2 +-
 arch/blackfin/mach-bf538/include/mach/blackfin.h  |   10 -
 arch/blackfin/mach-bf538/include/mach/cdefBF538.h |    1 +
 arch/blackfin/mach-bf548/boards/cm_bf548.c        |   19 +-
 arch/blackfin/mach-bf548/boards/ezkit.c           |   12 +-
 arch/blackfin/mach-bf548/dma.c                    |    8 +-
 arch/blackfin/mach-bf548/include/mach/anomaly.h   |   21 +-
 arch/blackfin/mach-bf548/include/mach/blackfin.h  |   89 ---
 arch/blackfin/mach-bf561/boards/cm_bf561.c        |  141 ++++-
 arch/blackfin/mach-bf561/boards/ezkit.c           |   13 +-
 arch/blackfin/mach-bf561/include/mach/anomaly.h   |    2 +
 arch/blackfin/mach-bf561/secondary.S              |   28 +-
 arch/blackfin/mach-common/Makefile                |    1 -
 arch/blackfin/mach-common/entry.S                 |  191 +++---
 arch/blackfin/mach-common/head.S                  |   19 +-
 arch/blackfin/mach-common/interrupt.S             |   78 ++--
 arch/blackfin/mach-common/ints-priority.c         |   19 +-
 arch/blackfin/mach-common/lock.S                  |  223 -------
 arch/blackfin/mach-common/pm.c                    |   64 +--
 arch/blackfin/mm/init.c                           |    3 +
 arch/blackfin/mm/isram-driver.c                   |  222 ++++++-
 arch/blackfin/mm/sram-alloc.c                     |   30 +-
 87 files changed, 3329 insertions(+), 2234 deletions(-)
 create mode 100644 arch/blackfin/kernel/shadow_console.c
 delete mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537.c
 create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537e.c
 create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537u.c
 delete mode 100644 arch/blackfin/mach-common/lock.S

[PATCH 01/72] Blackfin: bf537-stamp: update ADP5588 header name

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index bd65690..b8e8c92 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -1089,7 +1089,7 @@ static struct platform_device i2c_bfin_twi_device = {
 
 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
 #include <linux/input.h>
-#include <linux/i2c/adp5588_keys.h>
+#include <linux/i2c/adp5588.h>
 static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
 	[0]	 = KEY_GRAVE,
 	[1]	 = KEY_1,
-- 
1.6.4.2

[PATCH 02/72] Blackfin: bf537-stamp: declare SPI IRQ resources

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/bfin5xx_spi.h |    1 +
 arch/blackfin/mach-bf537/boards/stamp.c |    6 ++++++
 2 files changed, 7 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index aaeb4df..c281c63 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -127,6 +127,7 @@ struct bfin5xx_spi_chip {
 	u32 cs_gpio;
 	/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
 	u16 idle_tx_val;
+	u8 pio_interrupt; /* Enable spi data irq */
 };
 
 #endif /* _SPI_CHANNEL_H_ */
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index b8e8c92..d619313 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -555,6 +555,7 @@ static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 8,
+	.pio_interrupt = 0,
 };
 #endif
 
@@ -864,6 +865,11 @@ static struct resource bfin_spi0_resource[] = {
 	[1] = {
 		.start = CH_SPI,
 		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
 		.flags = IORESOURCE_IRQ,
 	},
 };
-- 
1.6.4.2

[PATCH 03/72] Blackfin: bf537-stamp: add resources for AD1938 audio card

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |   21 +++++++++++++++++++++
 1 files changed, 21 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d619313..b9da979 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -524,6 +524,15 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
+static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+	.cs_gpio = GPIO_PF5,
+};
+#endif
+
 #if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
 static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 	.enable_dma = 0,
@@ -754,6 +763,18 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
+
+#if defined(CONFIG_SND_BF5XX_SOC_AD1938) || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
+	{
+		.modalias = "ad1938-spi",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 0,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
+		.controller_data = &ad1938_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
 #if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
 	{
 		.modalias = "ad9960-spi",
-- 
1.6.4.2

[PATCH 04/72] Blackfin: make EVT3->EVT5 lowering more robust wrt IPEND[4]

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

We handle many exceptions at EVT5 (hardware error level) so that we can
catch exceptions in our exception handling code.  Today - if the global
interrupt enable bit (IPEND[4]) is set (interrupts disabled) our trap
handling code goes into a infinite loop, since we need interrupts to be
on to defer things to EVT5.

Normal kernel code should not trigger this for any reason as IPEND[4] gets
cleared early (when doing an interrupt context save) and the kernel stack
there should be sane (or something much worse is happening in the system).
But there have been a few times where this has happened, so this change
makes sure we dump a proper crash message even when things have gone south.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/pda.h    |    1 +
 arch/blackfin/kernel/asm-offsets.c |    1 +
 arch/blackfin/kernel/traps.c       |   19 ++++----
 arch/blackfin/mach-common/entry.S  |   86 ++++++++++++++++++++++-------------
 4 files changed, 66 insertions(+), 41 deletions(-)

diff --git a/arch/blackfin/include/asm/pda.h b/arch/blackfin/include/asm/pda.h
index b42555c..69b96b4 100644
--- a/arch/blackfin/include/asm/pda.h
+++ b/arch/blackfin/include/asm/pda.h
@@ -50,6 +50,7 @@ struct blackfin_pda {			/* Per-processor Data Area */
 	unsigned long ex_optr;
 	unsigned long ex_buf[4];
 	unsigned long ex_imask;		/* Saved imask from exception */
+	unsigned long ex_ipend;		/* Saved IPEND from exception */
 	unsigned long *ex_stack;	/* Exception stack space */
 
 #ifdef ANOMALY_05000261
diff --git a/arch/blackfin/kernel/asm-offsets.c b/arch/blackfin/kernel/asm-offsets.c
index b5df945..8ad4f2c 100644
--- a/arch/blackfin/kernel/asm-offsets.c
+++ b/arch/blackfin/kernel/asm-offsets.c
@@ -145,6 +145,7 @@ int main(void)
 	DEFINE(PDA_EXBUF, offsetof(struct blackfin_pda, ex_buf));
 	DEFINE(PDA_EXIMASK, offsetof(struct blackfin_pda, ex_imask));
 	DEFINE(PDA_EXSTACK, offsetof(struct blackfin_pda, ex_stack));
+	DEFINE(PDA_EXIPEND, offsetof(struct blackfin_pda, ex_ipend));
 #ifdef ANOMALY_05000261
 	DEFINE(PDA_LFRETX, offsetof(struct blackfin_pda, last_cplb_fault_retx));
 #endif
diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index bf2b2d1..fccf741 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -267,11 +267,6 @@ asmlinkage void trap_c(struct pt_regs *fp)
 	 * double faults if the stack has become corrupt
 	 */
 
-#ifndef CONFIG_KGDB
-	/* IPEND is skipped if KGDB isn't enabled (see entry code) */
-	fp->ipend = bfin_read_IPEND();
-#endif
-
 	/* trap_c() will be called for exceptions. During exceptions
 	 * processing, the pc value should be set with retx value.
 	 * With this change we can cleanup some code in signal.c- TODO
@@ -1116,10 +1111,16 @@ void show_regs(struct pt_regs *fp)
 
 	verbose_printk(KERN_NOTICE "%s", linux_banner);
 
-	verbose_printk(KERN_NOTICE "\nSEQUENCER STATUS:\t\t%s\n",
-		       print_tainted());
-	verbose_printk(KERN_NOTICE " SEQSTAT: %08lx  IPEND: %04lx  SYSCFG: %04lx\n",
-		       (long)fp->seqstat, fp->ipend, fp->syscfg);
+	verbose_printk(KERN_NOTICE "\nSEQUENCER STATUS:\t\t%s\n", print_tainted());
+	verbose_printk(KERN_NOTICE " SEQSTAT: %08lx  IPEND: %04lx  IMASK: %04lx  SYSCFG: %04lx\n",
+		(long)fp->seqstat, fp->ipend, cpu_pda[smp_processor_id()].ex_imask, fp->syscfg);
+	if (fp->ipend & EVT_IRPTEN)
+		verbose_printk(KERN_NOTICE "  Global Interrupts Disabled (IPEND[4])\n");
+	if (!(cpu_pda[smp_processor_id()].ex_imask & (EVT_IVG13 | EVT_IVG12 | EVT_IVG11 |
+			EVT_IVG10 | EVT_IVG9 | EVT_IVG8 | EVT_IVG7 | EVT_IVTMR)))
+		verbose_printk(KERN_NOTICE "  Peripheral interrupts masked off\n");
+	if (!(cpu_pda[smp_processor_id()].ex_imask & (EVT_IVG15 | EVT_IVG14)))
+		verbose_printk(KERN_NOTICE "  Kernel interrupts masked off\n");
 	if ((fp->seqstat & SEQSTAT_EXCAUSE) == VEC_HWERR) {
 		verbose_printk(KERN_NOTICE "  HWERRCAUSE: 0x%lx\n",
 			(fp->seqstat & SEQSTAT_HWERRCAUSE) >> 14);
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index fb1795d..4c07fcb 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -301,25 +301,31 @@ ENTRY(_ex_replaceable)
 	nop;
 
 ENTRY(_ex_trap_c)
+	/* The only thing that has been saved in this context is
+	 * (R7:6,P5:4), ASTAT & SP - don't use anything else
+	 */
+
+	GET_PDA(p5, r6);
+
 	/* Make sure we are not in a double fault */
 	p4.l = lo(IPEND);
 	p4.h = hi(IPEND);
 	r7 = [p4];
 	CC = BITTST (r7, 5);
 	if CC jump _double_fault;
+	[p5 + PDA_EXIPEND] = r7;
 
 	/* Call C code (trap_c) to handle the exception, which most
 	 * likely involves sending a signal to the current process.
 	 * To avoid double faults, lower our priority to IRQ5 first.
 	 */
-	P5.h = _exception_to_level5;
-	P5.l = _exception_to_level5;
+	r7.h = _exception_to_level5;
+	r7.l = _exception_to_level5;
 	p4.l = lo(EVT5);
 	p4.h = hi(EVT5);
-	[p4] = p5;
+	[p4] = r7;
 	csync;
 
-	GET_PDA(p5, r6);
 #ifndef CONFIG_DEBUG_DOUBLEFAULT
 
 	/*
@@ -349,8 +355,7 @@ ENTRY(_ex_trap_c)
 	BITCLR(r6, SYSCFG_SSSTEP_P);
 	SYSCFG = r6;
 
-	/* Disable all interrupts, but make sure level 5 is enabled so
-	 * we can switch to that level.  Save the old mask.  */
+	/* Save the current IMASK, since we change in order to jump to level 5 */
 	cli r6;
 	[p5 + PDA_EXIMASK] = r6;
 
@@ -358,9 +363,21 @@ ENTRY(_ex_trap_c)
 	p4.h = hi(SAFE_USER_INSTRUCTION);
 	retx = p4;
 
+	/* Disable all interrupts, but make sure level 5 is enabled so
+	 * we can switch to that level.
+	 */
 	r6 = 0x3f;
 	sti r6;
 
+	/* In case interrupts are disabled IPEND[4] (global interrupt disable bit)
+	 * clear it (re-enabling interrupts again) by the special sequence of pushing
+	 * RETI onto the stack.  This way we can lower ourselves to IVG5 even if the
+	 * exception was taken after the interrupt handler was called but before it
+	 * got a chance to enable global interrupts itself.
+	 */
+	[--sp] = reti;
+	sp += 4;
+
 	raise 5;
 	jump.s _bfin_return_from_exception;
 ENDPROC(_ex_trap_c)
@@ -420,47 +437,52 @@ ENDPROC(_double_fault)
 ENTRY(_exception_to_level5)
 	SAVE_ALL_SYS
 
-	GET_PDA(p4, r7);        /* Fetch current PDA */
-	r6 = [p4 + PDA_RETX];
+	GET_PDA(p5, r7);        /* Fetch current PDA */
+	r6 = [p5 + PDA_RETX];
 	[sp + PT_PC] = r6;
 
-	r6 = [p4 + PDA_SYSCFG];
+	r6 = [p5 + PDA_SYSCFG];
 	[sp + PT_SYSCFG] = r6;
 
-	/* Restore interrupt mask.  We haven't pushed RETI, so this
-	 * doesn't enable interrupts until we return from this handler.  */
-	r6 = [p4 + PDA_EXIMASK];
-	sti r6;
-
 	/* Restore the hardware error vector.  */
-	P5.h = _evt_ivhw;
-	P5.l = _evt_ivhw;
+	r7.h = _evt_ivhw;
+	r7.l = _evt_ivhw;
 	p4.l = lo(EVT5);
 	p4.h = hi(EVT5);
-	[p4] = p5;
+	[p4] = r7;
 	csync;
 
-	p2.l = lo(IPEND);
-	p2.h = hi(IPEND);
-	csync;
-	r0 = [p2];              /* Read current IPEND */
-	[sp + PT_IPEND] = r0;   /* Store IPEND */
+#ifdef CONFIG_DEBUG_DOUBLEFAULT
+	/* Now that we have the hardware error vector programmed properly
+	 * we can re-enable interrupts (IPEND[4]), so if the _trap_c causes
+	 * another hardware error, we can catch it (self-nesting).
+	 */
+	[--sp] = reti;
+	sp += 4;
+#endif
+
+	r7 = [p5 + PDA_EXIPEND]	/* Read the IPEND from the Exception state */
+	[sp + PT_IPEND] = r7;   /* Store IPEND onto the stack */
 
 	r0 = sp; 	/* stack frame pt_regs pointer argument ==> r0 */
 	SP += -12;
 	call _trap_c;
 	SP += 12;
 
-#ifdef CONFIG_DEBUG_DOUBLEFAULT
-	/* Grab ILAT */
-	p2.l = lo(ILAT);
-	p2.h = hi(ILAT);
-	r0 = [p2];
-	r1 = 0x20;  /* Did I just cause anther HW error? */
-	r0 = r0 & r1;
-	CC = R0 == R1;
-	if CC JUMP _double_fault;
-#endif
+	/* If interrupts were off during the exception (IPEND[4] = 1), turn them off
+	 * before we return.
+	 */
+	CC = BITTST(r7, EVT_IRPTEN_P)
+	if !CC jump 1f;
+	/* this will load a random value into the reti register - but that is OK,
+	 * since we do restore it to the correct value in the 'RESTORE_ALL_SYS' macro
+	 */
+	sp += -4;
+	reti = [sp++];
+1:
+	/* restore the interrupt mask (IMASK) */
+	r6 = [p5 + PDA_EXIMASK];
+	sti r6;
 
 	call _ret_from_exception;
 	RESTORE_ALL_SYS
-- 
1.6.4.2

[PATCH 05/72] Blackfin: checkpatch --file arch/blackfin/kernel/ipipe.c

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/ipipe.c |   36 +++++++++++++++++++-----------------
 1 files changed, 19 insertions(+), 17 deletions(-)

diff --git a/arch/blackfin/kernel/ipipe.c b/arch/blackfin/kernel/ipipe.c
index b8d2203..a725677 100644
--- a/arch/blackfin/kernel/ipipe.c
+++ b/arch/blackfin/kernel/ipipe.c
@@ -30,10 +30,10 @@
 #include <linux/slab.h>
 #include <linux/errno.h>
 #include <linux/kthread.h>
-#include <asm/unistd.h>
+#include <linux/unistd.h>
+#include <linux/io.h>
 #include <asm/system.h>
 #include <asm/atomic.h>
-#include <asm/io.h>
 
 DEFINE_PER_CPU(struct pt_regs, __ipipe_tick_regs);
 
@@ -90,6 +90,7 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
 	struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr();
 	struct ipipe_domain *this_domain, *next_domain;
 	struct list_head *head, *pos;
+	struct ipipe_irqdesc *idesc;
 	int m_ack, s = -1;
 
 	/*
@@ -100,17 +101,20 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
 	 */
 	m_ack = (regs == NULL || irq == IRQ_SYSTMR || irq == IRQ_CORETMR);
 	this_domain = __ipipe_current_domain;
+	idesc = &this_domain->irqs[irq];
 
-	if (unlikely(test_bit(IPIPE_STICKY_FLAG, &this_domain->irqs[irq].control)))
+	if (unlikely(test_bit(IPIPE_STICKY_FLAG, &idesc->control)))
 		head = &this_domain->p_link;
 	else {
 		head = __ipipe_pipeline.next;
 		next_domain = list_entry(head, struct ipipe_domain, p_link);
-		if (likely(test_bit(IPIPE_WIRED_FLAG, &next_domain->irqs[irq].control))) {
-			if (!m_ack && next_domain->irqs[irq].acknowledge != NULL)
-				next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
+		idesc = &next_domain->irqs[irq];
+		if (likely(test_bit(IPIPE_WIRED_FLAG, &idesc->control))) {
+			if (!m_ack && idesc->acknowledge != NULL)
+				idesc->acknowledge(irq, irq_to_desc(irq));
 			if (test_bit(IPIPE_SYNCDEFER_FLAG, &p->status))
-				s = __test_and_set_bit(IPIPE_STALL_FLAG, &p->status);
+				s = __test_and_set_bit(IPIPE_STALL_FLAG,
+						       &p->status);
 			__ipipe_dispatch_wired(next_domain, irq);
 			goto out;
 		}
@@ -121,14 +125,15 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
 	pos = head;
 	while (pos != &__ipipe_pipeline) {
 		next_domain = list_entry(pos, struct ipipe_domain, p_link);
-		if (test_bit(IPIPE_HANDLE_FLAG, &next_domain->irqs[irq].control)) {
+		idesc = &next_domain->irqs[irq];
+		if (test_bit(IPIPE_HANDLE_FLAG, &idesc->control)) {
 			__ipipe_set_irq_pending(next_domain, irq);
-			if (!m_ack && next_domain->irqs[irq].acknowledge != NULL) {
-				next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
+			if (!m_ack && idesc->acknowledge != NULL) {
+				idesc->acknowledge(irq, irq_to_desc(irq));
 				m_ack = 1;
 			}
 		}
-		if (!test_bit(IPIPE_PASS_FLAG, &next_domain->irqs[irq].control))
+		if (!test_bit(IPIPE_PASS_FLAG, &idesc->control))
 			break;
 		pos = next_domain->p_link.next;
 	}
@@ -333,12 +338,9 @@ asmlinkage void __ipipe_sync_root(void)
 
 void ___ipipe_sync_pipeline(unsigned long syncmask)
 {
-	if (__ipipe_root_domain_p) {
-		if (test_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status)))
-			return;
-	}
+	if (__ipipe_root_domain_p &&
+	    test_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status)))
+		return;
 
 	__ipipe_sync_stage(syncmask);
 }
-
-EXPORT_SYMBOL(show_stack);
-- 
1.6.4.2

[PATCH 06/72] Blackfin: fix misnomer of some I-pipe helpers

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

__ipipe_{stall, unstall}_root_raw() identifiers may leave the reader
under the impression that only the virtual state is affected by these
operations, which is wrong. Pick names following the convention used
throughout the interrupt pipeline code.

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/ipipe.h |    7 ------
 arch/blackfin/kernel/ipipe.c      |   44 ++++++++++++++++--------------------
 arch/blackfin/lib/ins.S           |    4 +-
 3 files changed, 22 insertions(+), 33 deletions(-)

diff --git a/arch/blackfin/include/asm/ipipe.h b/arch/blackfin/include/asm/ipipe.h
index 87ba9ad..4617ba6 100644
--- a/arch/blackfin/include/asm/ipipe.h
+++ b/arch/blackfin/include/asm/ipipe.h
@@ -145,10 +145,6 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs);
 
 int __ipipe_get_irq_priority(unsigned irq);
 
-void __ipipe_stall_root_raw(void);
-
-void __ipipe_unstall_root_raw(void);
-
 void __ipipe_serial_debug(const char *fmt, ...);
 
 asmlinkage void __ipipe_call_irqtail(unsigned long addr);
@@ -234,9 +230,6 @@ int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc);
 #define task_hijacked(p)		0
 #define ipipe_trap_notify(t, r)  	0
 
-#define __ipipe_stall_root_raw()	do { } while (0)
-#define __ipipe_unstall_root_raw()	do { } while (0)
-
 #define ipipe_init_irq_threads()		do { } while (0)
 #define ipipe_start_irq_thread(irq, desc)	0
 
diff --git a/arch/blackfin/kernel/ipipe.c b/arch/blackfin/kernel/ipipe.c
index a725677..be4f24e 100644
--- a/arch/blackfin/kernel/ipipe.c
+++ b/arch/blackfin/kernel/ipipe.c
@@ -191,30 +191,6 @@ void __ipipe_disable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
 }
 EXPORT_SYMBOL(__ipipe_disable_irqdesc);
 
-void __ipipe_stall_root_raw(void)
-{
-	/*
-	 * This code is called by the ins{bwl} routines (see
-	 * arch/blackfin/lib/ins.S), which are heavily used by the
-	 * network stack. It masks all interrupts but those handled by
-	 * non-root domains, so that we keep decent network transfer
-	 * rates for Linux without inducing pathological jitter for
-	 * the real-time domain.
-	 */
-	__asm__ __volatile__ ("sti %0;" : : "d"(__ipipe_irq_lvmask));
-
-	__set_bit(IPIPE_STALL_FLAG,
-		  &ipipe_root_cpudom_var(status));
-}
-
-void __ipipe_unstall_root_raw(void)
-{
-	__clear_bit(IPIPE_STALL_FLAG,
-		    &ipipe_root_cpudom_var(status));
-
-	__asm__ __volatile__ ("sti %0;" : : "d"(bfin_irq_flags));
-}
-
 int __ipipe_syscall_root(struct pt_regs *regs)
 {
 	struct ipipe_percpu_domain_data *p;
@@ -344,3 +320,23 @@ void ___ipipe_sync_pipeline(unsigned long syncmask)
 
 	__ipipe_sync_stage(syncmask);
 }
+
+void __ipipe_disable_root_irqs_hw(void)
+{
+	/*
+	 * This code is called by the ins{bwl} routines (see
+	 * arch/blackfin/lib/ins.S), which are heavily used by the
+	 * network stack. It masks all interrupts but those handled by
+	 * non-root domains, so that we keep decent network transfer
+	 * rates for Linux without inducing pathological jitter for
+	 * the real-time domain.
+	 */
+	bfin_sti(__ipipe_irq_lvmask);
+	__set_bit(IPIPE_STALL_FLAG, &ipipe_root_cpudom_var(status));
+}
+
+void __ipipe_enable_root_irqs_hw(void)
+{
+	__clear_bit(IPIPE_STALL_FLAG, &ipipe_root_cpudom_var(status));
+	bfin_sti(bfin_irq_flags);
+}
diff --git a/arch/blackfin/lib/ins.S b/arch/blackfin/lib/ins.S
index 1863a6b..3edbd8d 100644
--- a/arch/blackfin/lib/ins.S
+++ b/arch/blackfin/lib/ins.S
@@ -16,7 +16,7 @@
 	[--sp] = rets; \
 	[--sp] = (P5:0); \
 	sp += -12; \
-	call ___ipipe_stall_root_raw; \
+	call ___ipipe_disable_root_irqs_hw; \
 	sp += 12; \
 	(P5:0) = [sp++];
 # define CLI_INNER_NOP
@@ -28,7 +28,7 @@
 #ifdef CONFIG_IPIPE
 # define DO_STI \
 	sp += -12; \
-	call ___ipipe_unstall_root_raw; \
+	call ___ipipe_enable_root_irqs_hw; \
 	sp += 12; \
 2:	rets = [sp++];
 #else
-- 
1.6.4.2

[PATCH 07/72] Blackfin: export show_stack() to modules

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/traps.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index fccf741..5994597 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -944,6 +944,7 @@ void show_stack(struct task_struct *task, unsigned long *stack)
 	}
 #endif
 }
+EXPORT_SYMBOL(show_stack);
 
 void dump_stack(void)
 {
-- 
1.6.4.2

[PATCH 08/72] Blackfin: allow high priority domains to preempt schedule_tail()

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

ret_from_fork is always entered with hw interrupts off, which prevents
real-time domains to preempt the Linux kernel during part of the
initial context switch to the new task, which could in turn raise the
worst-case latency figures.

To avoid this, stall the root domain stage in the interrupt pipeline
to keep the scheduling tail code free from Linux-handled IRQs, then
enable hardware interrupts again.

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/entry.S |   24 ++++++++++++++++++++++--
 1 files changed, 22 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/kernel/entry.S b/arch/blackfin/kernel/entry.S
index a9cfba9..3f8769b 100644
--- a/arch/blackfin/kernel/entry.S
+++ b/arch/blackfin/kernel/entry.S
@@ -43,8 +43,28 @@
 
 ENTRY(_ret_from_fork)
 #ifdef CONFIG_IPIPE
-	[--sp] = reti; 		/* IRQs on. */
-	SP += 4;
+	/*
+	 * Hw IRQs are off on entry, and we don't want the scheduling tail
+	 * code to starve high priority domains from interrupts while it
+	 * runs. Therefore we first stall the root stage to have the
+	 * virtual interrupt state reflect IMASK.
+	 */
+	p0.l = ___ipipe_root_status;
+	p0.h = ___ipipe_root_status;
+	r4 = [p0];
+	bitset(r4, 0);
+	[p0] = r4;
+	/*
+	 * Then we may enable hw IRQs, allowing preemption from high
+	 * priority domains. schedule_tail() will do local_irq_enable()
+	 * since Blackfin does not define __ARCH_WANT_UNLOCKED_CTXSW, so
+	 * there is no need to unstall the root domain by ourselves
+	 * afterwards.
+	 */
+	p0.l = _bfin_irq_flags;
+	p0.h = _bfin_irq_flags;
+	r4 = [p0];
+	sti r4;
 #endif /* CONFIG_IPIPE */
 	SP += -12;
 	call _schedule_tail;
-- 
1.6.4.2

[PATCH 09/72] Blackfin: use generic name for EVT14 handler

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

The purpose of the EVT14 handler may depend on whether CONFIG_IPIPE is
enabled, albeit its implementation can be the same in both cases. When
the interrupt pipeline is enabled, EVT14 can be used to raise the core
priority level for the running code; when CONFIG_IPIPE is off, EVT14
can be used to lower this level before running softirq handlers.

Rename evt14_softirq to evt_evt14 to pick an identifier that fits
both, which allows to reuse the same vector setup code as well.

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/bfin-global.h   |    1 -
 arch/blackfin/include/asm/irq_handler.h   |    1 +
 arch/blackfin/mach-common/entry.S         |    8 ++++----
 arch/blackfin/mach-common/ints-priority.c |    2 +-
 4 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin-global.h b/arch/blackfin/include/asm/bfin-global.h
index e39277e..e6ecbe4 100644
--- a/arch/blackfin/include/asm/bfin-global.h
+++ b/arch/blackfin/include/asm/bfin-global.h
@@ -66,7 +66,6 @@ extern void program_IAR(void);
 
 extern asmlinkage void lower_to_irq14(void);
 extern asmlinkage void bfin_return_from_exception(void);
-extern asmlinkage void evt14_softirq(void);
 extern asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs);
 extern int bfin_internal_set_wake(unsigned int irq, unsigned int state);
 
diff --git a/arch/blackfin/include/asm/irq_handler.h b/arch/blackfin/include/asm/irq_handler.h
index 139b520..7d9e2d3 100644
--- a/arch/blackfin/include/asm/irq_handler.h
+++ b/arch/blackfin/include/asm/irq_handler.h
@@ -17,6 +17,7 @@ asmlinkage void evt_evt10(void);
 asmlinkage void evt_evt11(void);
 asmlinkage void evt_evt12(void);
 asmlinkage void evt_evt13(void);
+asmlinkage void evt_evt14(void);
 asmlinkage void evt_soft_int1(void);
 asmlinkage void evt_system_call(void);
 asmlinkage void init_exception_buff(void);
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 4c07fcb..919f7ae 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -975,10 +975,10 @@ ENTRY(_lower_to_irq14)
 #endif
 
 #ifdef CONFIG_DEBUG_HWERR
-	/* enable irq14 & hwerr interrupt, until we transition to _evt14_softirq */
+	/* enable irq14 & hwerr interrupt, until we transition to _evt_evt14 */
 	r0 = (EVT_IVG14 | EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
 #else
-	/* Only enable irq14 interrupt, until we transition to _evt14_softirq */
+	/* Only enable irq14 interrupt, until we transition to _evt_evt14 */
 	r0 = (EVT_IVG14 | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
 #endif
 	sti r0;
@@ -986,7 +986,7 @@ ENTRY(_lower_to_irq14)
 	rti;
 ENDPROC(_lower_to_irq14)
 
-ENTRY(_evt14_softirq)
+ENTRY(_evt_evt14)
 #ifdef CONFIG_DEBUG_HWERR
 	r0 = (EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
 	sti r0;
@@ -996,7 +996,7 @@ ENTRY(_evt14_softirq)
 	[--sp] = RETI;
 	SP += 4;
 	rts;
-ENDPROC(_evt14_softirq)
+ENDPROC(_evt_evt14)
 
 ENTRY(_schedule_and_signal_from_int)
 	/* To end up here, vector 15 was changed - so we have to change it
diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c
index b421501..4cc55bc 100644
--- a/arch/blackfin/mach-common/ints-priority.c
+++ b/arch/blackfin/mach-common/ints-priority.c
@@ -967,7 +967,7 @@ void __cpuinit init_exception_vectors(void)
 	bfin_write_EVT11(evt_evt11);
 	bfin_write_EVT12(evt_evt12);
 	bfin_write_EVT13(evt_evt13);
-	bfin_write_EVT14(evt14_softirq);
+	bfin_write_EVT14(evt_evt14);
 	bfin_write_EVT15(evt_system_call);
 	CSYNC();
 }
-- 
1.6.4.2

[PATCH 10/72] Blackfin: reuse evt_evt14 handler to perform irqtail epilogue

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-common/interrupt.S |   24 +-----------------------
 1 files changed, 1 insertions(+), 23 deletions(-)

diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index 9c46680..ae7fc88 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -276,33 +276,11 @@ ENTRY(___ipipe_call_irqtail)
 	( r7:4, p5:3 ) = [sp++];
 	rets = [sp++];
 
-	[--sp] = reti;
-	reti = [sp++];          /* IRQs are off. */
-	r0.h = 3f;
-	r0.l = 3f;
-	p0.l = lo(EVT14);
-	p0.h = hi(EVT14);
-	[p0] = r0;
-	csync;
 	r0 = 0x401f (z);
 	sti r0;
-	raise 14;
-	[--sp] = reti;          /* IRQs on. */
+	raise 14;		/* Branches to _evt_evt14 */
 2:
 	jump 2b;                /* Likely paranoid. */
-3:
-	sp += 4;                /* Discard saved RETI */
-	r0.h = _evt14_softirq;
-	r0.l = _evt14_softirq;
-	p0.l = lo(EVT14);
-	p0.h = hi(EVT14);
-	[p0] = r0;
-	csync;
-	p0.l = _bfin_irq_flags;
-	p0.h = _bfin_irq_flags;
-	r0 = [p0];
-	sti r0;
-	rts;
 ENDPROC(___ipipe_call_irqtail)
 
 #endif /* CONFIG_IPIPE */
-- 
1.6.4.2

[PATCH 11/72] Blackfin: allow EVT5 to preempt irqtail prologue (CONFIG_DEBUG_HWERR)

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-common/interrupt.S |   10 +++++++++-
 1 files changed, 9 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index ae7fc88..29fbf67 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -276,7 +276,15 @@ ENTRY(___ipipe_call_irqtail)
 	( r7:4, p5:3 ) = [sp++];
 	rets = [sp++];
 
-	r0 = 0x401f (z);
+#ifdef CONFIG_DEBUG_HWERR
+	/* enable irq14 & hwerr interrupt, until we transition to _evt_evt14 */
+	r0 = (EVT_IVG14 | EVT_IVHW | \
+		EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#else
+	/* Only enable irq14 interrupt, until we transition to _evt_evt14 */
+	r0 = (EVT_IVG14 | \
+		EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+#endif
 	sti r0;
 	raise 14;		/* Branches to _evt_evt14 */
 2:
-- 
1.6.4.2

[PATCH 12/72] Blackfin: document __ipipe_call_irqtail

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-common/interrupt.S |   25 +++++++++++++++++++++++++
 1 files changed, 25 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index 29fbf67..c754ff7 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -261,6 +261,31 @@ ENTRY(_evt_system_call)
 ENDPROC(_evt_system_call)
 
 #ifdef CONFIG_IPIPE
+/*
+ * __ipipe_call_irqtail: lowers the current priority level to EVT15
+ * before running a user-defined routine, then raises the priority
+ * level to EVT14 to prepare the caller for a normal interrupt
+ * return through RTI.
+ *
+ * We currently use this facility in two occasions:
+ *
+ * - to branch to __ipipe_irq_tail_hook as requested by a high
+ *   priority domain after the pipeline delivered an interrupt,
+ *   e.g. such as Xenomai, in order to start its rescheduling
+ *   procedure, since we may not switch tasks when IRQ levels are
+ *   nested on the Blackfin, so we have to fake an interrupt return
+ *   so that we may reschedule immediately.
+ *
+ * - to branch to sync_root_irqs, in order to play any interrupt
+ *   pending for the root domain (i.e. the Linux kernel). This lowers
+ *   the core priority level enough so that Linux IRQ handlers may
+ *   never delay interrupts handled by high priority domains; we defer
+ *   those handlers until this point instead. This is a substitute
+ *   to using a threaded interrupt model for the Linux kernel.
+ *
+ * r0: address of user-defined routine
+ * context: caller must have preempted EVT15, hw interrupts must be off.
+ */
 ENTRY(___ipipe_call_irqtail)
 	p0 = r0;
 	r0.l = 1f;
-- 
1.6.4.2

[PATCH 13/72] Blackfin: sanitize manual control of IPEND[4]

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Cleanup is performed in two ways:

- remove extraneous updates of IPEND[4] w/ CONFIG_IPIPE,
  and document remaining use.

- substitute pop-reg-from-stack instructions with plain SP fixups in
  all save-RETI-then-discard patterns.

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-common/entry.S |   25 +++++++++++--------------
 1 files changed, 11 insertions(+), 14 deletions(-)

diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 919f7ae..2c58b60 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -708,8 +708,14 @@ ENTRY(_system_call)
 #ifdef CONFIG_IPIPE
 	cc = BITTST(r7, TIF_IRQ_SYNC);
 	if !cc jump .Lsyscall_no_irqsync;
+	/*
+	 * Clear IPEND[4] manually to undo what resume_userspace_1 just did;
+	 * we need this so that high priority domain interrupts may still
+	 * preempt the current domain while the pipeline log is being played
+	 * back.
+	 */
 	[--sp] = reti;
-	r0 = [sp++];
+	SP += 4; /* don't merge with next insn to keep the pattern obvious */
 	SP += -12;
 	call ___ipipe_sync_root;
 	SP += 12;
@@ -721,7 +727,7 @@ ENTRY(_system_call)
 
 	/* Reenable interrupts.  */
 	[--sp] = reti;
-	r0 = [sp++];
+	sp += 4;
 
 	SP += -12;
 	call _schedule;
@@ -737,7 +743,7 @@ ENTRY(_system_call)
 .Lsyscall_do_signals:
 	/* Reenable interrupts.  */
 	[--sp] = reti;
-	r0 = [sp++];
+	sp += 4;
 
 	r0 = sp;
 	SP += -12;
@@ -747,10 +753,6 @@ ENTRY(_system_call)
 .Lsyscall_really_exit:
 	r5 = [sp + PT_RESERVED];
 	rets = r5;
-#ifdef CONFIG_IPIPE
-	[--sp] = reti;
-	r5 = [sp++];
-#endif /* CONFIG_IPIPE */
 	rts;
 ENDPROC(_system_call)
 
@@ -904,14 +906,9 @@ ENDPROC(_ret_from_exception)
 
 #ifdef CONFIG_IPIPE
 
-_sync_root_irqs:
-	[--sp] = reti;		/* Reenable interrupts */
-	r0 = [sp++];
-	jump.l ___ipipe_sync_root
-
 _resume_kernel_from_int:
-	r0.l = _sync_root_irqs
-	r0.h = _sync_root_irqs
+	r0.l = ___ipipe_sync_root;
+	r0.h = ___ipipe_sync_root;
 	[--sp] = rets;
 	[--sp] = ( r7:4, p5:3 );
 	SP += -12;
-- 
1.6.4.2

[PATCH 14/72] Blackfin: inline I-pipe bypass code in ret_from_exception

[Mike Frysinger]

From: Philippe Gerum <rpm@xenomai.org>

Signed-off-by: Philippe Gerum <rpm@xenomai.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/ipipe.c      |    5 -----
 arch/blackfin/mach-common/entry.S |   14 +++++++-------
 2 files changed, 7 insertions(+), 12 deletions(-)

diff --git a/arch/blackfin/kernel/ipipe.c b/arch/blackfin/kernel/ipipe.c
index be4f24e..5d73823 100644
--- a/arch/blackfin/kernel/ipipe.c
+++ b/arch/blackfin/kernel/ipipe.c
@@ -164,11 +164,6 @@ out:
 		__clear_bit(IPIPE_STALL_FLAG, &p->status);
 }
 
-int __ipipe_check_root(void)
-{
-	return ipipe_root_domain_p;
-}
-
 void __ipipe_enable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
 {
 	struct irq_desc *desc = irq_to_desc(irq);
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 2c58b60..cbc5b6d 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -840,13 +840,13 @@ ENDPROC(_resume)
 
 ENTRY(_ret_from_exception)
 #ifdef CONFIG_IPIPE
-	[--sp] = rets;
-	SP += -12;
-	call ___ipipe_check_root
-	SP += 12
-	rets = [sp++];
-	cc = r0 == 0;
-	if cc jump 4f;                /* not on behalf of Linux, get out */
+	p2.l = _per_cpu__ipipe_percpu_domain;
+	p2.h = _per_cpu__ipipe_percpu_domain;
+	r0.l = _ipipe_root;
+	r0.h = _ipipe_root;
+	r2 = [p2];
+	cc = r0 == r2;
+	if !cc jump 4f;  /* not on behalf of the root domain, get out */
 #endif /* CONFIG_IPIPE */
 	p2.l = lo(IPEND);
 	p2.h = hi(IPEND);
-- 
1.6.4.2

[PATCH 15/72] Blackfin: cleanup traps decode_address() a bit

[Mike Frysinger]

Unify the address display to shrink the code, and add missing decoding of
a few special Blackfin-specific regions (L1 ROM and MMRs).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/traps.c |   48 ++++++++++++++++++++++++++---------------
 1 files changed, 30 insertions(+), 18 deletions(-)

diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 5994597..519acca 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -100,7 +100,11 @@ static void decode_address(char *buf, unsigned long address)
 	char *modname;
 	char *delim = ":";
 	char namebuf[128];
+#endif
+
+	buf += sprintf(buf, "<0x%08lx> ", address);
 
+#ifdef CONFIG_KALLSYMS
 	/* look up the address and see if we are in kernel space */
 	symname = kallsyms_lookup(address, &symsize, &offset, &modname, namebuf);
 
@@ -108,23 +112,33 @@ static void decode_address(char *buf, unsigned long address)
 		/* yeah! kernel space! */
 		if (!modname)
 			modname = delim = "";
-		sprintf(buf, "<0x%p> { %s%s%s%s + 0x%lx }",
-		              (void *)address, delim, modname, delim, symname,
-		              (unsigned long)offset);
+		sprintf(buf, "{ %s%s%s%s + 0x%lx }",
+		        delim, modname, delim, symname,
+		        (unsigned long)offset);
 		return;
-
 	}
 #endif
 
-	/* Problem in fixed code section? */
 	if (address >= FIXED_CODE_START && address < FIXED_CODE_END) {
-		sprintf(buf, "<0x%p> /* Maybe fixed code section */", (void *)address);
+		/* Problem in fixed code section? */
+		strcat(buf, "/* Maybe fixed code section */");
+		return;
+
+	} else if (address < CONFIG_BOOT_LOAD) {
+		/* Problem somewhere before the kernel start address */
+		strcat(buf, "/* Maybe null pointer? */");
+		return;
+
+	} else if (address >= COREMMR_BASE) {
+		strcat(buf, "/* core mmrs */");
+		return;
+
+	} else if (address >= SYSMMR_BASE) {
+		strcat(buf, "/* system mmrs */");
 		return;
-	}
 
-	/* Problem somewhere before the kernel start address */
-	if (address < CONFIG_BOOT_LOAD) {
-		sprintf(buf, "<0x%p> /* Maybe null pointer? */", (void *)address);
+	} else if (address >= L1_ROM_START && address < L1_ROM_START + L1_ROM_LENGTH) {
+		strcat(buf, "/* on-chip L1 ROM */");
 		return;
 	}
 
@@ -172,18 +186,16 @@ static void decode_address(char *buf, unsigned long address)
 						offset = (address - vma->vm_start) +
 							 (vma->vm_pgoff << PAGE_SHIFT);
 
-					sprintf(buf, "<0x%p> [ %s + 0x%lx ]",
-						(void *)address, name, offset);
+					sprintf(buf, "[ %s + 0x%lx ]", name, offset);
 				} else
-					sprintf(buf, "<0x%p> [ %s vma:0x%lx-0x%lx]",
-						(void *)address, name,
-						vma->vm_start, vma->vm_end);
+					sprintf(buf, "[ %s vma:0x%lx-0x%lx]",
+						name, vma->vm_start, vma->vm_end);
 
 				if (!in_atomic)
 					mmput(mm);
 
-				if (!strlen(buf))
-					sprintf(buf, "<0x%p> [ %s ] dynamic memory", (void *)address, name);
+				if (buf[0] == '\0')
+					sprintf(buf, "[ %s ] dynamic memory", name);
 
 				goto done;
 			}
@@ -193,7 +205,7 @@ static void decode_address(char *buf, unsigned long address)
 	}
 
 	/* we were unable to find this address anywhere */
-	sprintf(buf, "<0x%p> /* kernel dynamic memory */", (void *)address);
+	sprintf(buf, "/* kernel dynamic memory */");
 
 done:
 	write_unlock_irqrestore(&tasklist_lock, flags);
-- 
1.6.4.2

[PATCH 16/72] Blackfin: convert ptrace to new memory functions

[Mike Frysinger]

Now that we have a Blackfin memory function to figure out how to properly
access the different regions, drop the custom memory range checks in our
ptrace code and use that.  It makes the code nicer and fixes bugs where
the ptrace logic wasn't handling all the different regions.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/ptrace.c |  129 +++++++++++++++++++++++------------------
 1 files changed, 72 insertions(+), 57 deletions(-)

diff --git a/arch/blackfin/kernel/ptrace.c b/arch/blackfin/kernel/ptrace.c
index 6a387ee..271d7c6 100644
--- a/arch/blackfin/kernel/ptrace.c
+++ b/arch/blackfin/kernel/ptrace.c
@@ -206,6 +206,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 {
 	int ret;
 	unsigned long __user *datap = (unsigned long __user *)data;
+	void *paddr = (void *)addr;
 
 	switch (request) {
 		/* when I and D space are separate, these will need to be fixed. */
@@ -215,42 +216,49 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 	case PTRACE_PEEKTEXT:	/* read word at location addr. */
 		{
 			unsigned long tmp = 0;
-			int copied;
+			int copied = 0, to_copy = sizeof(tmp);
 
 			ret = -EIO;
-			pr_debug("ptrace: PEEKTEXT at addr 0x%08lx + %ld\n", addr, sizeof(data));
-			if (is_user_addr_valid(child, addr, sizeof(tmp)) < 0)
+			pr_debug("ptrace: PEEKTEXT at addr 0x%08lx + %i\n", addr, to_copy);
+			if (is_user_addr_valid(child, addr, to_copy) < 0)
 				break;
 			pr_debug("ptrace: user address is valid\n");
 
-			if (L1_CODE_LENGTH != 0 && addr >= get_l1_code_start()
-			    && addr + sizeof(tmp) <= get_l1_code_start() + L1_CODE_LENGTH) {
-				safe_dma_memcpy (&tmp, (const void *)(addr), sizeof(tmp));
-				copied = sizeof(tmp);
-
-			} else if (L1_DATA_A_LENGTH != 0 && addr >= L1_DATA_A_START
-			    && addr + sizeof(tmp) <= L1_DATA_A_START + L1_DATA_A_LENGTH) {
-				memcpy(&tmp, (const void *)(addr), sizeof(tmp));
-				copied = sizeof(tmp);
-
-			} else if (L1_DATA_B_LENGTH != 0 && addr >= L1_DATA_B_START
-			    && addr + sizeof(tmp) <= L1_DATA_B_START + L1_DATA_B_LENGTH) {
-				memcpy(&tmp, (const void *)(addr), sizeof(tmp));
-				copied = sizeof(tmp);
-
-			} else if (addr >= FIXED_CODE_START
-			    && addr + sizeof(tmp) <= FIXED_CODE_END) {
-				copy_from_user_page(0, 0, 0, &tmp, (const void *)(addr), sizeof(tmp));
-				copied = sizeof(tmp);
-
-			} else
+			switch (bfin_mem_access_type(addr, to_copy)) {
+			case BFIN_MEM_ACCESS_CORE:
+			case BFIN_MEM_ACCESS_CORE_ONLY:
 				copied = access_process_vm(child, addr, &tmp,
-							   sizeof(tmp), 0);
+				                           to_copy, 0);
+				if (copied)
+					break;
+
+				/* hrm, why didn't that work ... maybe no mapping */
+				if (addr >= FIXED_CODE_START &&
+				    addr + to_copy <= FIXED_CODE_END) {
+					copy_from_user_page(0, 0, 0, &tmp, paddr, to_copy);
+					copied = to_copy;
+				} else if (addr >= BOOT_ROM_START) {
+					memcpy(&tmp, paddr, to_copy);
+					copied = to_copy;
+				}
 
-			pr_debug("ptrace: copied size %d [0x%08lx]\n", copied, tmp);
-			if (copied != sizeof(tmp))
 				break;
-			ret = put_user(tmp, datap);
+			case BFIN_MEM_ACCESS_DMA:
+				if (safe_dma_memcpy(&tmp, paddr, to_copy))
+					copied = to_copy;
+				break;
+			case BFIN_MEM_ACCESS_ITEST:
+				if (isram_memcpy(&tmp, paddr, to_copy))
+					copied = to_copy;
+				break;
+			default:
+				copied = 0;
+				break;
+			}
+
+			pr_debug("ptrace: copied size %d [0x%08lx]\n", copied, tmp);
+			if (copied == to_copy)
+				ret = put_user(tmp, datap);
 			break;
 		}
 
@@ -294,43 +302,50 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 		/* fall through */
 	case PTRACE_POKETEXT:	/* write the word at location addr. */
 		{
-			int copied;
+			int copied = 0, to_copy = sizeof(data);
 
 			ret = -EIO;
-			pr_debug("ptrace: POKETEXT at addr 0x%08lx + %ld bytes %lx\n",
-			         addr, sizeof(data), data);
-			if (is_user_addr_valid(child, addr, sizeof(data)) < 0)
+			pr_debug("ptrace: POKETEXT at addr 0x%08lx + %i bytes %lx\n",
+			         addr, to_copy, data);
+			if (is_user_addr_valid(child, addr, to_copy) < 0)
 				break;
 			pr_debug("ptrace: user address is valid\n");
 
-			if (L1_CODE_LENGTH != 0 && addr >= get_l1_code_start()
-			    && addr + sizeof(data) <= get_l1_code_start() + L1_CODE_LENGTH) {
-				safe_dma_memcpy ((void *)(addr), &data, sizeof(data));
-				copied = sizeof(data);
-
-			} else if (L1_DATA_A_LENGTH != 0 && addr >= L1_DATA_A_START
-			    && addr + sizeof(data) <= L1_DATA_A_START + L1_DATA_A_LENGTH) {
-				memcpy((void *)(addr), &data, sizeof(data));
-				copied = sizeof(data);
-
-			} else if (L1_DATA_B_LENGTH != 0 && addr >= L1_DATA_B_START
-			    && addr + sizeof(data) <= L1_DATA_B_START + L1_DATA_B_LENGTH) {
-				memcpy((void *)(addr), &data, sizeof(data));
-				copied = sizeof(data);
-
-			} else if (addr >= FIXED_CODE_START
-			    && addr + sizeof(data) <= FIXED_CODE_END) {
-				copy_to_user_page(0, 0, 0, (void *)(addr), &data, sizeof(data));
-				copied = sizeof(data);
-
-			} else
+			switch (bfin_mem_access_type(addr, to_copy)) {
+			case BFIN_MEM_ACCESS_CORE:
+			case BFIN_MEM_ACCESS_CORE_ONLY:
 				copied = access_process_vm(child, addr, &data,
-							   sizeof(data), 1);
+				                           to_copy, 0);
+				if (copied)
+					break;
+
+				/* hrm, why didn't that work ... maybe no mapping */
+				if (addr >= FIXED_CODE_START &&
+				    addr + to_copy <= FIXED_CODE_END) {
+					copy_to_user_page(0, 0, 0, paddr, &data, to_copy);
+					copied = to_copy;
+				} else if (addr >= BOOT_ROM_START) {
+					memcpy(paddr, &data, to_copy);
+					copied = to_copy;
+				}
 
-			pr_debug("ptrace: copied size %d\n", copied);
-			if (copied != sizeof(data))
 				break;
-			ret = 0;
+			case BFIN_MEM_ACCESS_DMA:
+				if (safe_dma_memcpy(paddr, &data, to_copy))
+					copied = to_copy;
+				break;
+			case BFIN_MEM_ACCESS_ITEST:
+				if (isram_memcpy(paddr, &data, to_copy))
+					copied = to_copy;
+				break;
+			default:
+				copied = 0;
+				break;
+			}
+
+			pr_debug("ptrace: copied size %d\n", copied);
+			if (copied == to_copy)
+				ret = 0;
 			break;
 		}
 
-- 
1.6.4.2

[PATCH 17/72] Blackfin: reject outdated/unused/wrong relocation types

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

All kernel modules are required to be built with -mlong-calls and thus
should not generate any of these relocations.  If they do, it means the
module has not been compiled properly, so rather than trying to handle
them (and running into random run time errors) just error out on module
load to force the module to be compiled correctly.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/module.c |   42 +++++++---------------------------------
 1 files changed, 8 insertions(+), 34 deletions(-)

diff --git a/arch/blackfin/kernel/module.c b/arch/blackfin/kernel/module.c
index d5aee36..bb94078 100644
--- a/arch/blackfin/kernel/module.c
+++ b/arch/blackfin/kernel/module.c
@@ -243,40 +243,6 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 #endif
 		switch (ELF32_R_TYPE(rel[i].r_info)) {
 
-		case R_BFIN_PCREL24:
-		case R_BFIN_PCREL24_JUMP_L:
-			/* Add the value, subtract its postition */
-			location16 =
-			    (uint16_t *) (sechdrs[sechdrs[relsec].sh_info].
-					  sh_addr + rel[i].r_offset - 2);
-			location32 = (uint32_t *) location16;
-			value -= (uint32_t) location32;
-			value >>= 1;
-			if ((value & 0xFF000000) != 0 &&
-			    (value & 0xFF000000) != 0xFF000000) {
-				printk(KERN_ERR "module %s: relocation overflow\n",
-				       mod->name);
-				return -ENOEXEC;
-			}
-			pr_debug("value is %x, before %x-%x after %x-%x\n", value,
-			       *location16, *(location16 + 1),
-			       (*location16 & 0xff00) | (value >> 16 & 0x00ff),
-			       value & 0xffff);
-			*location16 =
-			    (*location16 & 0xff00) | (value >> 16 & 0x00ff);
-			*(location16 + 1) = value & 0xffff;
-			break;
-		case R_BFIN_PCREL12_JUMP:
-		case R_BFIN_PCREL12_JUMP_S:
-			value -= (uint32_t) location32;
-			value >>= 1;
-			*location16 = (value & 0xfff);
-			break;
-		case R_BFIN_PCREL10:
-			value -= (uint32_t) location32;
-			value >>= 1;
-			*location16 = (value & 0x3ff);
-			break;
 		case R_BFIN_LUIMM16:
 			pr_debug("before %x after %x\n", *location16,
 				       (value & 0xffff));
@@ -302,6 +268,14 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 			pr_debug("before %x after %x\n", *location32, value);
 			*location32 = value;
 			break;
+		case R_BFIN_PCREL24:
+		case R_BFIN_PCREL24_JUMP_L:
+		case R_BFIN_PCREL12_JUMP:
+		case R_BFIN_PCREL12_JUMP_S:
+		case R_BFIN_PCREL10:
+			printk(KERN_ERR "module %s: Unsupported relocation: %u (no -mlong-calls?)\n"
+				mod->name, ELF32_R_TYPE(rel[i].r_info));
+			return -ENOEXEC;
 		default:
 			printk(KERN_ERR "module %s: Unknown relocation: %u\n",
 			       mod->name, ELF32_R_TYPE(rel[i].r_info));
-- 
1.6.4.2

[PATCH 18/72] Blackfin: cleanup printk() usage in module code

[Mike Frysinger]

Convert all printk() statements to use the common pr_xxx() funcs and use
the new pr_fmt() function to standardize all of the output.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/module.c |   59 +++++++++++++++++-----------------------
 1 files changed, 25 insertions(+), 34 deletions(-)

diff --git a/arch/blackfin/kernel/module.c b/arch/blackfin/kernel/module.c
index bb94078..b8f4c67 100644
--- a/arch/blackfin/kernel/module.c
+++ b/arch/blackfin/kernel/module.c
@@ -27,6 +27,7 @@
  * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#define pr_fmt(fmt) "module %s: " fmt
 
 #include <linux/moduleloader.h>
 #include <linux/elf.h>
@@ -72,9 +73,8 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l1_inst_sram_alloc(s->sh_size);
 			mod->arch.text_l1 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-				       "module %s: L1 instruction memory allocation failed\n",
-				       mod->name);
+				pr_err("L1 inst memory allocation failed\n",
+					mod->name);
 				return -1;
 			}
 			dma_memcpy(dest, (void *)s->sh_addr, s->sh_size);
@@ -87,8 +87,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l1_data_sram_alloc(s->sh_size);
 			mod->arch.data_a_l1 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L1 data memory allocation failed\n",
+				pr_err("L1 data memory allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -102,8 +101,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l1_data_sram_alloc(s->sh_size);
 			mod->arch.bss_a_l1 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L1 data memory allocation failed\n",
+				pr_err("L1 data memory allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -115,8 +113,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l1_data_B_sram_alloc(s->sh_size);
 			mod->arch.data_b_l1 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L1 data memory allocation failed\n",
+				pr_err("L1 data memory allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -128,8 +125,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l1_data_B_sram_alloc(s->sh_size);
 			mod->arch.bss_b_l1 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L1 data memory allocation failed\n",
+				pr_err("L1 data memory allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -143,9 +139,8 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l2_sram_alloc(s->sh_size);
 			mod->arch.text_l2 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-				       "module %s: L2 SRAM allocation failed\n",
-				       mod->name);
+				pr_err("L2 SRAM allocation failed\n",
+					mod->name);
 				return -1;
 			}
 			memcpy(dest, (void *)s->sh_addr, s->sh_size);
@@ -158,8 +153,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l2_sram_alloc(s->sh_size);
 			mod->arch.data_l2 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L2 SRAM allocation failed\n",
+				pr_err("L2 SRAM allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -173,8 +167,7 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 			dest = l2_sram_alloc(s->sh_size);
 			mod->arch.bss_l2 = dest;
 			if (dest == NULL) {
-				printk(KERN_ERR
-					"module %s: L2 SRAM allocation failed\n",
+				pr_err("L2 SRAM allocation failed\n",
 					mod->name);
 				return -1;
 			}
@@ -190,7 +183,7 @@ int
 apply_relocate(Elf_Shdr * sechdrs, const char *strtab,
 	       unsigned int symindex, unsigned int relsec, struct module *me)
 {
-	printk(KERN_ERR "module %s: .rel unsupported\n", me->name);
+	pr_err(".rel unsupported\n", me->name);
 	return -ENOEXEC;
 }
 
@@ -217,8 +210,8 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 	uint16_t *location16;
 	uint32_t value;
 
-	pr_debug("Applying relocate section %u to %u\n", relsec,
-	       sechdrs[relsec].sh_info);
+	pr_debug("applying relocate section %u to %u\n", mod->name,
+		relsec, sechdrs[relsec].sh_info);
 	for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
 		/* This is where to make the change */
 		location16 =
@@ -231,21 +224,22 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 		    + ELF32_R_SYM(rel[i].r_info);
 		value = sym->st_value;
 		value += rel[i].r_addend;
-		pr_debug("location is %x, value is %x type is %d \n",
-			 (unsigned int) location32, value,
-			 ELF32_R_TYPE(rel[i].r_info));
+
 #ifdef CONFIG_SMP
 		if ((unsigned long)location16 >= COREB_L1_DATA_A_START) {
-			printk(KERN_ERR "module %s: cannot relocate in L1: %u (SMP kernel)",
-				       mod->name, ELF32_R_TYPE(rel[i].r_info));
+			pr_err("cannot relocate in L1: %u (SMP kernel)",
+				mod->name, ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
 		}
 #endif
+
+		pr_debug("location is %lx, value is %x type is %d\n",
+			mod->name, (unsigned long)location32, value,
+			ELF32_R_TYPE(rel[i].r_info));
+
 		switch (ELF32_R_TYPE(rel[i].r_info)) {
 
 		case R_BFIN_LUIMM16:
-			pr_debug("before %x after %x\n", *location16,
-				       (value & 0xffff));
 			tmp = (value & 0xffff);
 			if ((unsigned long)location16 >= L1_CODE_START) {
 				dma_memcpy(location16, &tmp, 2);
@@ -253,8 +247,6 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 				*location16 = tmp;
 			break;
 		case R_BFIN_HUIMM16:
-			pr_debug("before %x after %x\n", *location16,
-				       ((value >> 16) & 0xffff));
 			tmp = ((value >> 16) & 0xffff);
 			if ((unsigned long)location16 >= L1_CODE_START) {
 				dma_memcpy(location16, &tmp, 2);
@@ -265,7 +257,6 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 			*location16 = (value & 0xffff);
 			break;
 		case R_BFIN_BYTE4_DATA:
-			pr_debug("before %x after %x\n", *location32, value);
 			*location32 = value;
 			break;
 		case R_BFIN_PCREL24:
@@ -273,12 +264,12 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 		case R_BFIN_PCREL12_JUMP:
 		case R_BFIN_PCREL12_JUMP_S:
 		case R_BFIN_PCREL10:
-			printk(KERN_ERR "module %s: Unsupported relocation: %u (no -mlong-calls?)\n"
+			pr_err("unsupported relocation: %u (no -mlong-calls?)\n",
 				mod->name, ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
 		default:
-			printk(KERN_ERR "module %s: Unknown relocation: %u\n",
-			       mod->name, ELF32_R_TYPE(rel[i].r_info));
+			pr_err("unknown relocation: %u\n", mod->name,
+				ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
 		}
 	}
-- 
1.6.4.2

[PATCH 19/72] Blackfin: convert malloc()/memset() to zalloc() in module code

[Mike Frysinger]

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/module.c |    6 ++----
 1 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/kernel/module.c b/arch/blackfin/kernel/module.c
index b8f4c67..50d7fbf 100644
--- a/arch/blackfin/kernel/module.c
+++ b/arch/blackfin/kernel/module.c
@@ -98,14 +98,13 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 		if (strcmp(".l1.bss", secstrings + s->sh_name) == 0 ||
 		    ((strcmp(".bss", secstrings + s->sh_name) == 0) &&
 		     (hdr->e_flags & EF_BFIN_DATA_IN_L1) && (s->sh_size > 0))) {
-			dest = l1_data_sram_alloc(s->sh_size);
+			dest = l1_data_sram_zalloc(s->sh_size);
 			mod->arch.bss_a_l1 = dest;
 			if (dest == NULL) {
 				pr_err("L1 data memory allocation failed\n",
 					mod->name);
 				return -1;
 			}
-			memset(dest, 0, s->sh_size);
 			s->sh_flags &= ~SHF_ALLOC;
 			s->sh_addr = (unsigned long)dest;
 		}
@@ -164,14 +163,13 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 		if (strcmp(".l2.bss", secstrings + s->sh_name) == 0 ||
 		    ((strcmp(".bss", secstrings + s->sh_name) == 0) &&
 		     (hdr->e_flags & EF_BFIN_DATA_IN_L2) && (s->sh_size > 0))) {
-			dest = l2_sram_alloc(s->sh_size);
+			dest = l2_sram_zalloc(s->sh_size);
 			mod->arch.bss_l2 = dest;
 			if (dest == NULL) {
 				pr_err("L2 SRAM allocation failed\n",
 					mod->name);
 				return -1;
 			}
-			memset(dest, 0, s->sh_size);
 			s->sh_flags &= ~SHF_ALLOC;
 			s->sh_addr = (unsigned long)dest;
 		}
-- 
1.6.4.2

[PATCH 20/72] Blackfin: cleanup module section checking

[Mike Frysinger]

The current module section handling code has a lot of verbose statements
copied and pasted throughout which makes it pretty hard to digest at a
glance.  By unifying all of these up front, it is a lot easier to quickly
get an idea of what is actually going on.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/module.c |  111 ++++++++++++++++++++++-------------------
 1 files changed, 60 insertions(+), 51 deletions(-)

diff --git a/arch/blackfin/kernel/module.c b/arch/blackfin/kernel/module.c
index 50d7fbf..2ad805e 100644
--- a/arch/blackfin/kernel/module.c
+++ b/arch/blackfin/kernel/module.c
@@ -53,7 +53,7 @@ void module_free(struct module *mod, void *module_region)
 
 /* Transfer the section to the L1 memory */
 int
-module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
+module_frob_arch_sections(Elf_Ehdr *hdr, Elf_Shdr *sechdrs,
 			  char *secstrings, struct module *mod)
 {
 	/*
@@ -64,12 +64,18 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 	 * NOTE: this breaks the semantic of mod->arch structure.
 	 */
 	Elf_Shdr *s, *sechdrs_end = sechdrs + hdr->e_shnum;
-	void *dest = NULL;
+	void *dest;
 
 	for (s = sechdrs; s < sechdrs_end; ++s) {
-		if ((strcmp(".l1.text", secstrings + s->sh_name) == 0) ||
-		    ((strcmp(".text", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_CODE_IN_L1) && (s->sh_size > 0))) {
+		const char *shname = secstrings + s->sh_name;
+
+		if (s->sh_size == 0)
+			continue;
+
+		if (!strcmp(".l1.text", shname) ||
+		    (!strcmp(".text", shname) &&
+		     (hdr->e_flags & EF_BFIN_CODE_IN_L1))) {
+
 			dest = l1_inst_sram_alloc(s->sh_size);
 			mod->arch.text_l1 = dest;
 			if (dest == NULL) {
@@ -78,12 +84,11 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			dma_memcpy(dest, (void *)s->sh_addr, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if ((strcmp(".l1.data", secstrings + s->sh_name) == 0) ||
-		    ((strcmp(".data", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_DATA_IN_L1) && (s->sh_size > 0))) {
+
+		} else if (!strcmp(".l1.data", shname) ||
+		           (!strcmp(".data", shname) &&
+		            (hdr->e_flags & EF_BFIN_DATA_IN_L1))) {
+
 			dest = l1_data_sram_alloc(s->sh_size);
 			mod->arch.data_a_l1 = dest;
 			if (dest == NULL) {
@@ -92,12 +97,11 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			memcpy(dest, (void *)s->sh_addr, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if (strcmp(".l1.bss", secstrings + s->sh_name) == 0 ||
-		    ((strcmp(".bss", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_DATA_IN_L1) && (s->sh_size > 0))) {
+
+		} else if (!strcmp(".l1.bss", shname) ||
+		           (!strcmp(".bss", shname) &&
+		            (hdr->e_flags & EF_BFIN_DATA_IN_L1))) {
+
 			dest = l1_data_sram_zalloc(s->sh_size);
 			mod->arch.bss_a_l1 = dest;
 			if (dest == NULL) {
@@ -105,10 +109,9 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 					mod->name);
 				return -1;
 			}
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if (strcmp(".l1.data.B", secstrings + s->sh_name) == 0) {
+
+		} else if (!strcmp(".l1.data.B", shname)) {
+
 			dest = l1_data_B_sram_alloc(s->sh_size);
 			mod->arch.data_b_l1 = dest;
 			if (dest == NULL) {
@@ -117,10 +120,9 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			memcpy(dest, (void *)s->sh_addr, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if (strcmp(".l1.bss.B", secstrings + s->sh_name) == 0) {
+
+		} else if (!strcmp(".l1.bss.B", shname)) {
+
 			dest = l1_data_B_sram_alloc(s->sh_size);
 			mod->arch.bss_b_l1 = dest;
 			if (dest == NULL) {
@@ -129,12 +131,11 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			memset(dest, 0, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if ((strcmp(".l2.text", secstrings + s->sh_name) == 0) ||
-		    ((strcmp(".text", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_CODE_IN_L2) && (s->sh_size > 0))) {
+
+		} else if (!strcmp(".l2.text", shname) ||
+		           (!strcmp(".text", shname) &&
+		            (hdr->e_flags & EF_BFIN_CODE_IN_L2))) {
+
 			dest = l2_sram_alloc(s->sh_size);
 			mod->arch.text_l2 = dest;
 			if (dest == NULL) {
@@ -143,12 +144,11 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			memcpy(dest, (void *)s->sh_addr, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if ((strcmp(".l2.data", secstrings + s->sh_name) == 0) ||
-		    ((strcmp(".data", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_DATA_IN_L2) && (s->sh_size > 0))) {
+
+		} else if (!strcmp(".l2.data", shname) ||
+		           (!strcmp(".data", shname) &&
+		            (hdr->e_flags & EF_BFIN_DATA_IN_L2))) {
+
 			dest = l2_sram_alloc(s->sh_size);
 			mod->arch.data_l2 = dest;
 			if (dest == NULL) {
@@ -157,12 +157,11 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 				return -1;
 			}
 			memcpy(dest, (void *)s->sh_addr, s->sh_size);
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
-		if (strcmp(".l2.bss", secstrings + s->sh_name) == 0 ||
-		    ((strcmp(".bss", secstrings + s->sh_name) == 0) &&
-		     (hdr->e_flags & EF_BFIN_DATA_IN_L2) && (s->sh_size > 0))) {
+
+		} else if (!strcmp(".l2.bss", shname) ||
+		           (!strcmp(".bss", shname) &&
+		            (hdr->e_flags & EF_BFIN_DATA_IN_L2))) {
+
 			dest = l2_sram_zalloc(s->sh_size);
 			mod->arch.bss_l2 = dest;
 			if (dest == NULL) {
@@ -170,10 +169,14 @@ module_frob_arch_sections(Elf_Ehdr * hdr, Elf_Shdr * sechdrs,
 					mod->name);
 				return -1;
 			}
-			s->sh_flags &= ~SHF_ALLOC;
-			s->sh_addr = (unsigned long)dest;
-		}
+
+		} else
+			continue;
+
+		s->sh_flags &= ~SHF_ALLOC;
+		s->sh_addr = (unsigned long)dest;
 	}
+
 	return 0;
 }
 
@@ -295,22 +298,28 @@ module_finalize(const Elf_Ehdr * hdr,
 	for (i = 1; i < hdr->e_shnum; i++) {
 		const char *strtab = (char *)sechdrs[strindex].sh_addr;
 		unsigned int info = sechdrs[i].sh_info;
+		const char *shname = secstrings + sechdrs[i].sh_name;
 
 		/* Not a valid relocation section? */
 		if (info >= hdr->e_shnum)
 			continue;
 
-		if ((sechdrs[i].sh_type == SHT_RELA) &&
-		    ((strcmp(".rela.l2.text", secstrings + sechdrs[i].sh_name) == 0) ||
-		    (strcmp(".rela.l1.text", secstrings + sechdrs[i].sh_name) == 0) ||
-		    ((strcmp(".rela.text", secstrings + sechdrs[i].sh_name) == 0) &&
-			(hdr->e_flags & (EF_BFIN_CODE_IN_L1|EF_BFIN_CODE_IN_L2))))) {
+		/* Only support RELA relocation types */
+		if (sechdrs[i].sh_type != SHT_RELA)
+			continue;
+
+		if (!strcmp(".rela.l2.text", shname) ||
+		    !strcmp(".rela.l1.text", shname) ||
+		    (!strcmp(".rela.text", shname) &&
+			 (hdr->e_flags & (EF_BFIN_CODE_IN_L1 | EF_BFIN_CODE_IN_L2)))) {
+
 			err = apply_relocate_add((Elf_Shdr *) sechdrs, strtab,
 					   symindex, i, mod);
 			if (err < 0)
 				return -ENOEXEC;
 		}
 	}
+
 	return 0;
 }
 
-- 
1.6.4.2

[PATCH 21/72] Blackfin: fix module reloc handling for all memory regions

[Mike Frysinger]

The current module relocation code has spotty handling wrt different
memory regions (like L1 instruction).  Rather than try to fix each
little spot, use the new common memory functions to greatly simplify
everything and make sure it is always correct.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/module.c |   62 ++++++++++++++++++++++------------------
 1 files changed, 34 insertions(+), 28 deletions(-)

diff --git a/arch/blackfin/kernel/module.c b/arch/blackfin/kernel/module.c
index 2ad805e..67fc7a5 100644
--- a/arch/blackfin/kernel/module.c
+++ b/arch/blackfin/kernel/module.c
@@ -37,6 +37,7 @@
 #include <linux/kernel.h>
 #include <asm/dma.h>
 #include <asm/cacheflush.h>
+#include <asm/uaccess.h>
 
 void *module_alloc(unsigned long size)
 {
@@ -199,26 +200,23 @@ apply_relocate(Elf_Shdr * sechdrs, const char *strtab,
 /*            gas does not generate it.                                  */
 /*************************************************************************/
 int
-apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
+apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab,
 		   unsigned int symindex, unsigned int relsec,
 		   struct module *mod)
 {
 	unsigned int i;
-	unsigned short tmp;
 	Elf32_Rela *rel = (void *)sechdrs[relsec].sh_addr;
 	Elf32_Sym *sym;
-	uint32_t *location32;
-	uint16_t *location16;
-	uint32_t value;
+	unsigned long location, value, size;
 
 	pr_debug("applying relocate section %u to %u\n", mod->name,
 		relsec, sechdrs[relsec].sh_info);
+
 	for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
 		/* This is where to make the change */
-		location16 =
-		    (uint16_t *) (sechdrs[sechdrs[relsec].sh_info].sh_addr +
-				  rel[i].r_offset);
-		location32 = (uint32_t *) location16;
+		location = sechdrs[sechdrs[relsec].sh_info].sh_addr +
+		           rel[i].r_offset;
+
 		/* This is the symbol it is referring to. Note that all
 		   undefined symbols have been resolved. */
 		sym = (Elf32_Sym *) sechdrs[symindex].sh_addr
@@ -227,39 +225,28 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 		value += rel[i].r_addend;
 
 #ifdef CONFIG_SMP
-		if ((unsigned long)location16 >= COREB_L1_DATA_A_START) {
+		if (location >= COREB_L1_DATA_A_START) {
 			pr_err("cannot relocate in L1: %u (SMP kernel)",
 				mod->name, ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
 		}
 #endif
 
-		pr_debug("location is %lx, value is %x type is %d\n",
-			mod->name, (unsigned long)location32, value,
-			ELF32_R_TYPE(rel[i].r_info));
+		pr_debug("location is %lx, value is %lx type is %d\n",
+			mod->name, location, value, ELF32_R_TYPE(rel[i].r_info));
 
 		switch (ELF32_R_TYPE(rel[i].r_info)) {
 
-		case R_BFIN_LUIMM16:
-			tmp = (value & 0xffff);
-			if ((unsigned long)location16 >= L1_CODE_START) {
-				dma_memcpy(location16, &tmp, 2);
-			} else
-				*location16 = tmp;
-			break;
 		case R_BFIN_HUIMM16:
-			tmp = ((value >> 16) & 0xffff);
-			if ((unsigned long)location16 >= L1_CODE_START) {
-				dma_memcpy(location16, &tmp, 2);
-			} else
-				*location16 = tmp;
-			break;
+			value >>= 16;
+		case R_BFIN_LUIMM16:
 		case R_BFIN_RIMM16:
-			*location16 = (value & 0xffff);
+			size = 2;
 			break;
 		case R_BFIN_BYTE4_DATA:
-			*location32 = value;
+			size = 4;
 			break;
+
 		case R_BFIN_PCREL24:
 		case R_BFIN_PCREL24_JUMP_L:
 		case R_BFIN_PCREL12_JUMP:
@@ -268,12 +255,31 @@ apply_relocate_add(Elf_Shdr * sechdrs, const char *strtab,
 			pr_err("unsupported relocation: %u (no -mlong-calls?)\n",
 				mod->name, ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
+
 		default:
 			pr_err("unknown relocation: %u\n", mod->name,
 				ELF32_R_TYPE(rel[i].r_info));
 			return -ENOEXEC;
 		}
+
+		switch (bfin_mem_access_type(location, size)) {
+		case BFIN_MEM_ACCESS_CORE:
+		case BFIN_MEM_ACCESS_CORE_ONLY:
+			memcpy((void *)location, &value, size);
+			break;
+		case BFIN_MEM_ACCESS_DMA:
+			dma_memcpy((void *)location, &value, size);
+			break;
+		case BFIN_MEM_ACCESS_ITEST:
+			isram_memcpy((void *)location, &value, size);
+			break;
+		default:
+			pr_err("invalid relocation for %#lx\n",
+				mod->name, location);
+			return -ENOEXEC;
+		}
 	}
+
 	return 0;
 }
 
-- 
1.6.4.2

[PATCH 22/72] Blackfin: clean up early memory setup code

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

Remove code duplication, and only print out memory warnings when they are
an actual problem.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/setup.c |   60 ++++++++++++++++++++++-------------------
 1 files changed, 32 insertions(+), 28 deletions(-)

diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index 6225eda..6dbf219 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -511,6 +511,7 @@ static __init void memory_setup(void)
 #ifdef CONFIG_MTD_UCLINUX
 	unsigned long mtd_phys = 0;
 #endif
+	unsigned long max_mem;
 
 	_rambase = (unsigned long)_stext;
 	_ramstart = (unsigned long)_end;
@@ -520,7 +521,22 @@ static __init void memory_setup(void)
 		panic("DMA region exceeds memory limit: %lu.",
 			_ramend - _ramstart);
 	}
-	memory_end = _ramend - DMA_UNCACHED_REGION;
+	max_mem = memory_end = _ramend - DMA_UNCACHED_REGION;
+
+#if (defined(CONFIG_BFIN_EXTMEM_ICACHEABLE) && ANOMALY_05000263)
+	/* Due to a Hardware Anomaly we need to limit the size of usable
+	 * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
+	 * 05000263 - Hardware loop corrupted when taking an ICPLB exception
+	 */
+# if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
+	if (max_mem >= 56 * 1024 * 1024)
+		max_mem = 56 * 1024 * 1024;
+# else
+	if (max_mem >= 60 * 1024 * 1024)
+		max_mem = 60 * 1024 * 1024;
+# endif				/* CONFIG_DEBUG_HUNT_FOR_ZERO */
+#endif				/* ANOMALY_05000263 */
+
 
 #ifdef CONFIG_MPU
 	/* Round up to multiple of 4MB */
@@ -549,22 +565,16 @@ static __init void memory_setup(void)
 
 # if defined(CONFIG_ROMFS_FS)
 	if (((unsigned long *)mtd_phys)[0] == ROMSB_WORD0
-	    && ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1)
+	    && ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1) {
 		mtd_size =
 		    PAGE_ALIGN(be32_to_cpu(((unsigned long *)mtd_phys)[2]));
-#  if (defined(CONFIG_BFIN_EXTMEM_ICACHEABLE) && ANOMALY_05000263)
-	/* Due to a Hardware Anomaly we need to limit the size of usable
-	 * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
-	 * 05000263 - Hardware loop corrupted when taking an ICPLB exception
-	 */
-#   if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
-	if (memory_end >= 56 * 1024 * 1024)
-		memory_end = 56 * 1024 * 1024;
-#   else
-	if (memory_end >= 60 * 1024 * 1024)
-		memory_end = 60 * 1024 * 1024;
-#   endif				/* CONFIG_DEBUG_HUNT_FOR_ZERO */
-#  endif				/* ANOMALY_05000263 */
+
+		/* ROM_FS is XIP, so if we found it, we need to limit memory */
+		if (memory_end > max_mem) {
+			pr_info("Limiting kernel memory to %liMB due to anomaly 05000263\n", max_mem >> 20);
+			memory_end = max_mem;
+		}
+	}
 # endif				/* CONFIG_ROMFS_FS */
 
 	/* Since the default MTD_UCLINUX has no magic number, we just blindly
@@ -586,20 +596,14 @@ static __init void memory_setup(void)
 	}
 #endif				/* CONFIG_MTD_UCLINUX */
 
-#if (defined(CONFIG_BFIN_EXTMEM_ICACHEABLE) && ANOMALY_05000263)
-	/* Due to a Hardware Anomaly we need to limit the size of usable
-	 * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
-	 * 05000263 - Hardware loop corrupted when taking an ICPLB exception
+	/* We need lo limit memory, since everything could have a text section
+	 * of userspace in it, and expose anomaly 05000263. If the anomaly
+	 * doesn't exist, or we don't need to - then dont.
 	 */
-#if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
-	if (memory_end >= 56 * 1024 * 1024)
-		memory_end = 56 * 1024 * 1024;
-#else
-	if (memory_end >= 60 * 1024 * 1024)
-		memory_end = 60 * 1024 * 1024;
-#endif				/* CONFIG_DEBUG_HUNT_FOR_ZERO */
-	printk(KERN_NOTICE "Warning: limiting memory to %liMB due to hardware anomaly 05000263\n", memory_end >> 20);
-#endif				/* ANOMALY_05000263 */
+	if (memory_end > max_mem) {
+		pr_info("Limiting kernel memory to %liMB due to anomaly 05000263\n", max_mem >> 20);
+		memory_end = max_mem;
+	}
 
 #ifdef CONFIG_MPU
 	page_mask_nelts = ((_ramend >> PAGE_SHIFT) + 31) / 32;
-- 
1.6.4.2

[PATCH 23/72] Blackfin: rename PCF8574 driver config

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

The "TWI_KEYPAD" driver was renamed to "INPUT_PCF8574", so update the
defines in the board resources accordingly.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf518/boards/ezbrd.c    |    2 +-
 arch/blackfin/mach-bf527/boards/cm_bf527.c |    2 +-
 arch/blackfin/mach-bf527/boards/ezbrd.c    |    2 +-
 arch/blackfin/mach-bf527/boards/ezkit.c    |    2 +-
 arch/blackfin/mach-bf533/boards/stamp.c    |    2 +-
 arch/blackfin/mach-bf537/boards/stamp.c    |    2 +-
 arch/blackfin/mach-bf548/boards/ezkit.c    |    2 +-
 7 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 809be26..4c594e6 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -539,7 +539,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index b09484f..3a62066 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -799,7 +799,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		.type = "pcf8574_lcd",
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.type = "pcf8574_keypad",
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 2ad68cd..809c790 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -596,7 +596,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 75e563d..b843d0e 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -863,7 +863,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PF8,
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 3d743cc..42d4c9f 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -458,7 +458,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = 39,
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index b9da979..72d11de 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -1348,7 +1348,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = IRQ_PG6,
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index dc0dd9b..aa82836 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -869,7 +869,7 @@ static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 	},
 #endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 		.irq = 212,
-- 
1.6.4.2

[PATCH 24/72] Blackfin: unify duplicated SMP checks in L2 cache kconfig

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig |    4 +---
 1 files changed, 1 insertions(+), 3 deletions(-)

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 7faa2f5..8d04ed9 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -987,7 +987,7 @@ endchoice
 config BFIN_L2_DCACHEABLE
 	bool "Enable DCACHE for L2 SRAM"
 	depends on BFIN_DCACHE
-	depends on BF54x || BF561
+	depends on (BF54x || BF561) && !SMP
 	default n
 choice
 	prompt "L2 SRAM DCACHE policy"
@@ -995,11 +995,9 @@ choice
 	default BFIN_L2_WRITEBACK
 config BFIN_L2_WRITEBACK
 	bool "Write back"
-	depends on !SMP
 
 config BFIN_L2_WRITETHROUGH
 	bool "Write through"
-	depends on !SMP
 endchoice
 
 
-- 
1.6.4.2

[PATCH 25/72] Blackfin: push SRAM locks down into related ifdefs

[Mike Frysinger]

Rather than defining the locks and initializing them all the time, only do
so when we actually need them (i.e. the SRAM regions exist).  This avoids
dead data and code bloat during runtime.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mm/sram-alloc.c |   30 +++++++++++++++++-------------
 1 files changed, 17 insertions(+), 13 deletions(-)

diff --git a/arch/blackfin/mm/sram-alloc.c b/arch/blackfin/mm/sram-alloc.c
index 0bc3c4e..e095094 100644
--- a/arch/blackfin/mm/sram-alloc.c
+++ b/arch/blackfin/mm/sram-alloc.c
@@ -42,11 +42,6 @@
 #include <asm/mem_map.h>
 #include "blackfin_sram.h"
 
-static DEFINE_PER_CPU(spinlock_t, l1sram_lock) ____cacheline_aligned_in_smp;
-static DEFINE_PER_CPU(spinlock_t, l1_data_sram_lock) ____cacheline_aligned_in_smp;
-static DEFINE_PER_CPU(spinlock_t, l1_inst_sram_lock) ____cacheline_aligned_in_smp;
-static spinlock_t l2_sram_lock ____cacheline_aligned_in_smp;
-
 /* the data structure for L1 scratchpad and DATA SRAM */
 struct sram_piece {
 	void *paddr;
@@ -55,6 +50,7 @@ struct sram_piece {
 	struct sram_piece *next;
 };
 
+static DEFINE_PER_CPU(spinlock_t, l1sram_lock) ____cacheline_aligned_in_smp;
 static DEFINE_PER_CPU(struct sram_piece, free_l1_ssram_head);
 static DEFINE_PER_CPU(struct sram_piece, used_l1_ssram_head);
 
@@ -68,12 +64,18 @@ static DEFINE_PER_CPU(struct sram_piece, free_l1_data_B_sram_head);
 static DEFINE_PER_CPU(struct sram_piece, used_l1_data_B_sram_head);
 #endif
 
+#if L1_DATA_A_LENGTH || L1_DATA_B_LENGTH
+static DEFINE_PER_CPU(spinlock_t, l1_data_sram_lock) ____cacheline_aligned_in_smp;
+#endif
+
 #if L1_CODE_LENGTH != 0
+static DEFINE_PER_CPU(spinlock_t, l1_inst_sram_lock) ____cacheline_aligned_in_smp;
 static DEFINE_PER_CPU(struct sram_piece, free_l1_inst_sram_head);
 static DEFINE_PER_CPU(struct sram_piece, used_l1_inst_sram_head);
 #endif
 
 #if L2_LENGTH != 0
+static spinlock_t l2_sram_lock ____cacheline_aligned_in_smp;
 static struct sram_piece free_l2_sram_head, used_l2_sram_head;
 #endif
 
@@ -225,10 +227,10 @@ static void __init l2_sram_init(void)
 	printk(KERN_INFO "Blackfin L2 SRAM: %d KB (%d KB free)\n",
 		L2_LENGTH >> 10,
 		free_l2_sram_head.next->size >> 10);
-#endif
 
 	/* mutex initialize */
 	spin_lock_init(&l2_sram_lock);
+#endif
 }
 
 static int __init bfin_sram_init(void)
@@ -416,18 +418,17 @@ EXPORT_SYMBOL(sram_free);
 
 void *l1_data_A_sram_alloc(size_t size)
 {
+#if L1_DATA_A_LENGTH != 0
 	unsigned long flags;
-	void *addr = NULL;
+	void *addr;
 	unsigned int cpu;
 
 	cpu = get_cpu();
 	/* add mutex operation */
 	spin_lock_irqsave(&per_cpu(l1_data_sram_lock, cpu), flags);
 
-#if L1_DATA_A_LENGTH != 0
 	addr = _sram_alloc(size, &per_cpu(free_l1_data_A_sram_head, cpu),
 			&per_cpu(used_l1_data_A_sram_head, cpu));
-#endif
 
 	/* add mutex operation */
 	spin_unlock_irqrestore(&per_cpu(l1_data_sram_lock, cpu), flags);
@@ -437,11 +438,15 @@ void *l1_data_A_sram_alloc(size_t size)
 		 (long unsigned int)addr, size);
 
 	return addr;
+#else
+	return NULL;
+#endif
 }
 EXPORT_SYMBOL(l1_data_A_sram_alloc);
 
 int l1_data_A_sram_free(const void *addr)
 {
+#if L1_DATA_A_LENGTH != 0
 	unsigned long flags;
 	int ret;
 	unsigned int cpu;
@@ -450,18 +455,17 @@ int l1_data_A_sram_free(const void *addr)
 	/* add mutex operation */
 	spin_lock_irqsave(&per_cpu(l1_data_sram_lock, cpu), flags);
 
-#if L1_DATA_A_LENGTH != 0
 	ret = _sram_free(addr, &per_cpu(free_l1_data_A_sram_head, cpu),
 			&per_cpu(used_l1_data_A_sram_head, cpu));
-#else
-	ret = -1;
-#endif
 
 	/* add mutex operation */
 	spin_unlock_irqrestore(&per_cpu(l1_data_sram_lock, cpu), flags);
 	put_cpu();
 
 	return ret;
+#else
+	return -1;
+#endif
 }
 EXPORT_SYMBOL(l1_data_A_sram_free);
 
-- 
1.6.4.2

[PATCH 26/72] Blackfin: add support for common FDPIC ptrace requests

[Mike Frysinger]

The FDPIC arches support a standard set of ptrace requests so rather than
define our own custom API, hook up those requests for common code to
leverage.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/ptrace.c |   26 ++++++++++++++++++++++++--
 1 files changed, 24 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/kernel/ptrace.c b/arch/blackfin/kernel/ptrace.c
index 271d7c6..30f4828 100644
--- a/arch/blackfin/kernel/ptrace.c
+++ b/arch/blackfin/kernel/ptrace.c
@@ -285,9 +285,9 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 				tmp = child->mm->start_data;
 #ifdef CONFIG_BINFMT_ELF_FDPIC
 			} else if (addr == (sizeof(struct pt_regs) + 12)) {
-				tmp = child->mm->context.exec_fdpic_loadmap;
+				goto case_PTRACE_GETFDPIC_EXEC;
 			} else if (addr == (sizeof(struct pt_regs) + 16)) {
-				tmp = child->mm->context.interp_fdpic_loadmap;
+				goto case_PTRACE_GETFDPIC_INTERP;
 #endif
 			} else {
 				tmp = get_reg(child, addr);
@@ -296,6 +296,28 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
 			break;
 		}
 
+#ifdef CONFIG_BINFMT_ELF_FDPIC
+	case PTRACE_GETFDPIC: {
+		unsigned long tmp = 0;
+
+		switch (addr) {
+		case_PTRACE_GETFDPIC_EXEC:
+		case PTRACE_GETFDPIC_EXEC:
+			tmp = child->mm->context.exec_fdpic_loadmap;
+			break;
+		case_PTRACE_GETFDPIC_INTERP:
+		case PTRACE_GETFDPIC_INTERP:
+			tmp = child->mm->context.interp_fdpic_loadmap;
+			break;
+		default:
+			break;
+		}
+
+		ret = put_user(tmp, datap);
+		break;
+	}
+#endif
+
 		/* when I and D space are separate, this will have to be fixed. */
 	case PTRACE_POKEDATA:
 		pr_debug("ptrace: PTRACE_PEEKDATA\n");
-- 
1.6.4.2

[PATCH 27/72] Blackfin: add an early shadow console

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

Add a memory based shadow console to keep a copy of the printk buffer in a
location which can be found externally.  This allows bootloaders to locate
and utilize the log buffer in case of silent (early/resume/etc...) crashes.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/early_printk.h |    2 +
 arch/blackfin/kernel/Makefile            |    1 +
 arch/blackfin/kernel/setup.c             |    2 +
 arch/blackfin/kernel/shadow_console.c    |   78 ++++++++++++++++++++++++++++++
 4 files changed, 83 insertions(+), 0 deletions(-)
 create mode 100644 arch/blackfin/kernel/shadow_console.c

diff --git a/arch/blackfin/include/asm/early_printk.h b/arch/blackfin/include/asm/early_printk.h
index 110f1c1..f5b6b7d 100644
--- a/arch/blackfin/include/asm/early_printk.h
+++ b/arch/blackfin/include/asm/early_printk.h
@@ -23,6 +23,8 @@
 
 #ifdef CONFIG_EARLY_PRINTK
 extern int setup_early_printk(char *);
+extern void enable_shadow_console(void);
 #else
 #define setup_early_printk(fmt) do { } while (0)
+#define enable_shadow_console(fmt)  do { } while (0)
 #endif /* CONFIG_EARLY_PRINTK */
diff --git a/arch/blackfin/kernel/Makefile b/arch/blackfin/kernel/Makefile
index 141d928..a8ddbc8 100644
--- a/arch/blackfin/kernel/Makefile
+++ b/arch/blackfin/kernel/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_MODULES)                += module.o
 obj-$(CONFIG_KGDB)                   += kgdb.o
 obj-$(CONFIG_KGDB_TESTS)             += kgdb_test.o
 obj-$(CONFIG_EARLY_PRINTK)           += early_printk.o
+obj-$(CONFIG_EARLY_PRINTK)           += shadow_console.o
 obj-$(CONFIG_STACKTRACE)             += stacktrace.o
 
 # the kgdb test puts code into L2 and without linker
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index 6dbf219..3974764 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -810,6 +810,8 @@ void __init setup_arch(char **cmdline_p)
 {
 	unsigned long sclk, cclk;
 
+	enable_shadow_console();
+
 	/* Check to make sure we are running on the right processor */
 	if (unlikely(CPUID != bfin_cpuid()))
 		printk(KERN_ERR "ERROR: Not running on ADSP-%s: unknown CPUID 0x%04x Rev 0.%d\n",
diff --git a/arch/blackfin/kernel/shadow_console.c b/arch/blackfin/kernel/shadow_console.c
new file mode 100644
index 0000000..15819ff
--- /dev/null
+++ b/arch/blackfin/kernel/shadow_console.c
@@ -0,0 +1,78 @@
+/*
+ * manage a small early shadow of the log buffer which we can pass between the
+ * bootloader so early crash messages are communicated properly and easily
+ *
+ * Copyright 2009 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/string.h>
+#include <asm/blackfin.h>
+#include <asm/irq_handler.h>
+#include <asm/early_printk.h>
+
+#define SHADOW_CONSOLE_START		(0x500)
+#define SHADOW_CONSOLE_END		(0x1000)
+#define SHADOW_CONSOLE_MAGIC_LOC	(0x4F0)
+#define SHADOW_CONSOLE_MAGIC		(0xDEADBEEF)
+
+static __initdata char *shadow_console_buffer = (char *)SHADOW_CONSOLE_START;
+
+static __init void early_shadow_write(struct console *con, const char *s,
+				unsigned int n)
+{
+	/*
+	 * save 2 bytes for the double null at the end
+	 * once we fail on a long line, make sure we don't write a short line afterwards
+	 */
+	if ((shadow_console_buffer + n) <= (char *)(SHADOW_CONSOLE_END - 2)) {
+		memcpy(shadow_console_buffer, s, n);
+		shadow_console_buffer += n;
+		shadow_console_buffer[0] = 0;
+		shadow_console_buffer[1] = 0;
+	} else
+		shadow_console_buffer = (char *)SHADOW_CONSOLE_END;
+}
+
+static __initdata struct console early_shadow_console = {
+	.name = "early_shadow",
+	.write = early_shadow_write,
+	.flags = CON_BOOT | CON_PRINTBUFFER,
+	.index = -1,
+	.device = 0,
+};
+
+__init void enable_shadow_console(void)
+{
+	int *loc = (int *)SHADOW_CONSOLE_MAGIC_LOC;
+
+	if (!(early_shadow_console.flags & CON_ENABLED)) {
+		register_console(&early_shadow_console);
+		/* for now, assume things are going to fail */
+		*loc = SHADOW_CONSOLE_MAGIC;
+		loc++;
+		*loc = SHADOW_CONSOLE_START;
+	}
+}
+
+static __init int disable_shadow_console(void)
+{
+	/*
+	 * by the time pure_initcall runs, the standard console is enabled,
+	 * and the early_console is off, so unset the magic numbers
+	 * unregistering the console is taken care of in common code (See
+	 * ./kernel/printk:disable_boot_consoles() )
+	 */
+	int *loc = (int *)SHADOW_CONSOLE_MAGIC_LOC;
+
+	*loc = 0;
+
+	return 0;
+}
+pure_initcall(disable_shadow_console);
-- 
1.6.4.2

[PATCH 28/72] Blackfin: catch hardware errors earlier during booting

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

Allow hardware errors to be caught during early portions of booting, and
leave something in the shadow console that people can use to debug their
system with (to be printed out by the bootloader on next reset).

This enables the hardare error interrupts in head.S, allowing us to find
hardware errors when they happen (well, as much as you can with a hardware
error) and prints out the trace if it is enabled.  This will catch errors
(like booting the wrong image on a 533) which previously resulted in a
infinite loop/hang, as well as random hardware errors before before
setup_arch().

To disable this debug only feature - turn off EARLY_PRINTK.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/early_printk.h |   22 +++++++++
 arch/blackfin/kernel/bfin_dma_5xx.c      |    6 ++
 arch/blackfin/kernel/early_printk.c      |   74 ++++++++++++++++++++++++++++--
 arch/blackfin/kernel/setup.c             |    3 +
 arch/blackfin/kernel/shadow_console.c    |   51 +++++++++++++++++---
 arch/blackfin/mach-common/head.S         |   11 ++++
 arch/blackfin/mm/init.c                  |    3 +
 7 files changed, 158 insertions(+), 12 deletions(-)

diff --git a/arch/blackfin/include/asm/early_printk.h b/arch/blackfin/include/asm/early_printk.h
index f5b6b7d..53a762b 100644
--- a/arch/blackfin/include/asm/early_printk.h
+++ b/arch/blackfin/include/asm/early_printk.h
@@ -21,10 +21,32 @@
  * GNU General Public License for more details.
  */
 
+
+#ifndef __ASM_EARLY_PRINTK_H__
+#define __ASM_EARLY_PRINTK_H__
+
 #ifdef CONFIG_EARLY_PRINTK
+/* For those that don't include it already */
+#include <linux/console.h>
+
 extern int setup_early_printk(char *);
 extern void enable_shadow_console(void);
+extern int shadow_console_enabled(void);
+extern void mark_shadow_error(void);
+extern void early_shadow_reg(unsigned long reg, unsigned int n);
+extern void early_shadow_write(struct console *con, const char *s,
+	unsigned int n) __attribute__((nonnull(2)));
+#define early_shadow_puts(str) early_shadow_write(NULL, str, strlen(str))
+#define early_shadow_stamp() \
+	do { \
+		early_shadow_puts(__FILE__ " : " __stringify(__LINE__) " ["); \
+		early_shadow_puts(__func__); \
+		early_shadow_puts("]\n"); \
+	} while (0)
 #else
 #define setup_early_printk(fmt) do { } while (0)
 #define enable_shadow_console(fmt)  do { } while (0)
+#define early_shadow_stamp() do { } while (0)
 #endif /* CONFIG_EARLY_PRINTK */
+
+#endif /* __ASM_EARLY_PRINTK_H__ */
diff --git a/arch/blackfin/kernel/bfin_dma_5xx.c b/arch/blackfin/kernel/bfin_dma_5xx.c
index 9f9b828..14dea1a 100644
--- a/arch/blackfin/kernel/bfin_dma_5xx.c
+++ b/arch/blackfin/kernel/bfin_dma_5xx.c
@@ -19,6 +19,7 @@
 #include <asm/cacheflush.h>
 #include <asm/dma.h>
 #include <asm/uaccess.h>
+#include <asm/early_printk.h>
 
 /*
  * To make sure we work around 05000119 - we always check DMA_DONE bit,
@@ -236,6 +237,7 @@ void blackfin_dma_resume(void)
  */
 void __init blackfin_dma_early_init(void)
 {
+	early_shadow_stamp();
 	bfin_write_MDMA_S0_CONFIG(0);
 	bfin_write_MDMA_S1_CONFIG(0);
 }
@@ -246,6 +248,8 @@ void __init early_dma_memcpy(void *pdst, const void *psrc, size_t size)
 	unsigned long src = (unsigned long)psrc;
 	struct dma_register *dst_ch, *src_ch;
 
+	early_shadow_stamp();
+
 	/* We assume that everything is 4 byte aligned, so include
 	 * a basic sanity check
 	 */
@@ -300,6 +304,8 @@ void __init early_dma_memcpy(void *pdst, const void *psrc, size_t size)
 
 void __init early_dma_memcpy_done(void)
 {
+	early_shadow_stamp();
+
 	while ((bfin_read_MDMA_S0_CONFIG() && !(bfin_read_MDMA_D0_IRQ_STATUS() & DMA_DONE)) ||
 	       (bfin_read_MDMA_S1_CONFIG() && !(bfin_read_MDMA_D1_IRQ_STATUS() & DMA_DONE)))
 		continue;
diff --git a/arch/blackfin/kernel/early_printk.c b/arch/blackfin/kernel/early_printk.c
index 2ab5681..931c78b 100644
--- a/arch/blackfin/kernel/early_printk.c
+++ b/arch/blackfin/kernel/early_printk.c
@@ -27,6 +27,7 @@
 #include <linux/serial_core.h>
 #include <linux/console.h>
 #include <linux/string.h>
+#include <linux/reboot.h>
 #include <asm/blackfin.h>
 #include <asm/irq_handler.h>
 #include <asm/early_printk.h>
@@ -181,6 +182,22 @@ asmlinkage void __init init_early_exception_vectors(void)
 	u32 evt;
 	SSYNC();
 
+	/*
+	 * This starts up the shadow buffer, incase anything crashes before
+	 * setup arch
+	 */
+	mark_shadow_error();
+	early_shadow_puts(linux_banner);
+	early_shadow_stamp();
+
+	if (CPUID != bfin_cpuid()) {
+		early_shadow_puts("Running on wrong machine type, expected");
+		early_shadow_reg(CPUID, 16);
+		early_shadow_puts(", but running on");
+		early_shadow_reg(bfin_cpuid(), 16);
+		early_shadow_puts("\n");
+	}
+
 	/* cannot program in software:
 	 * evt0 - emulation (jtag)
 	 * evt1 - reset
@@ -199,6 +216,7 @@ asmlinkage void __init init_early_exception_vectors(void)
 
 }
 
+__attribute__((__noreturn__))
 asmlinkage void __init early_trap_c(struct pt_regs *fp, void *retaddr)
 {
 	/* This can happen before the uart is initialized, so initialize
@@ -210,10 +228,58 @@ asmlinkage void __init early_trap_c(struct pt_regs *fp, void *retaddr)
 	if (likely(early_console == NULL) && CPUID == bfin_cpuid())
 		setup_early_printk(DEFAULT_EARLY_PORT);
 
-	printk(KERN_EMERG "Early panic\n");
-	dump_bfin_mem(fp);
-	show_regs(fp);
-	dump_bfin_trace_buffer();
+	if (!shadow_console_enabled()) {
+		/* crap - we crashed before setup_arch() */
+		early_shadow_puts("panic before setup_arch\n");
+		early_shadow_puts("IPEND:");
+		early_shadow_reg(fp->ipend, 16);
+		if (fp->seqstat & SEQSTAT_EXCAUSE) {
+			early_shadow_puts("\nEXCAUSE:");
+			early_shadow_reg(fp->seqstat & SEQSTAT_EXCAUSE, 8);
+		}
+		if (fp->seqstat & SEQSTAT_HWERRCAUSE) {
+			early_shadow_puts("\nHWERRCAUSE:");
+			early_shadow_reg(
+				(fp->seqstat & SEQSTAT_HWERRCAUSE) >> 14, 8);
+		}
+		early_shadow_puts("\nErr @");
+		if (fp->ipend & EVT_EVX)
+			early_shadow_reg(fp->retx, 32);
+		else
+			early_shadow_reg(fp->pc, 32);
+#ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
+		early_shadow_puts("\nTrace:");
+		if (likely(bfin_read_TBUFSTAT() & TBUFCNT)) {
+			while (bfin_read_TBUFSTAT() & TBUFCNT) {
+				early_shadow_puts("\nT  :");
+				early_shadow_reg(bfin_read_TBUF(), 32);
+				early_shadow_puts("\n S :");
+				early_shadow_reg(bfin_read_TBUF(), 32);
+			}
+		}
+#endif
+		early_shadow_puts("\nUse bfin-elf-addr2line to determine "
+			"function names\n");
+		/*
+		 * We should panic(), but we can't - since panic calls printk,
+		 * and printk uses memcpy.
+		 * we want to reboot, but if the machine type is different,
+		 * can't due to machine specific reboot sequences
+		 */
+		if (CPUID == bfin_cpuid()) {
+			early_shadow_puts("Trying to restart\n");
+			machine_restart("");
+		}
+
+		early_shadow_puts("Halting, since it is not safe to restart\n");
+		while (1)
+			asm volatile ("EMUEXCPT; IDLE;\n");
+
+	} else {
+		printk(KERN_EMERG "Early panic\n");
+		show_regs(fp);
+		dump_bfin_trace_buffer();
+	}
 
 	panic("Died early");
 }
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index 3974764..f92fffc 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -187,6 +187,8 @@ void __init bfin_relocate_l1_mem(void)
 	unsigned long l1_data_b_length;
 	unsigned long l2_length;
 
+	early_shadow_stamp();
+
 	/*
 	 * due to the ALIGN(4) in the arch/blackfin/kernel/vmlinux.lds.S
 	 * we know that everything about l1 text/data is nice and aligned,
@@ -1352,6 +1354,7 @@ const struct seq_operations cpuinfo_op = {
 
 void __init cmdline_init(const char *r0)
 {
+	early_shadow_stamp();
 	if (r0)
 		strncpy(command_line, r0, COMMAND_LINE_SIZE);
 }
diff --git a/arch/blackfin/kernel/shadow_console.c b/arch/blackfin/kernel/shadow_console.c
index 15819ff..8b8c710 100644
--- a/arch/blackfin/kernel/shadow_console.c
+++ b/arch/blackfin/kernel/shadow_console.c
@@ -24,15 +24,18 @@
 
 static __initdata char *shadow_console_buffer = (char *)SHADOW_CONSOLE_START;
 
-static __init void early_shadow_write(struct console *con, const char *s,
+__init void early_shadow_write(struct console *con, const char *s,
 				unsigned int n)
 {
+	unsigned int i;
 	/*
 	 * save 2 bytes for the double null at the end
 	 * once we fail on a long line, make sure we don't write a short line afterwards
 	 */
 	if ((shadow_console_buffer + n) <= (char *)(SHADOW_CONSOLE_END - 2)) {
-		memcpy(shadow_console_buffer, s, n);
+		/* can't use memcpy - it may not be relocated yet */
+		for (i = 0; i <= n; i++)
+			shadow_console_buffer[i] = s[i];
 		shadow_console_buffer += n;
 		shadow_console_buffer[0] = 0;
 		shadow_console_buffer[1] = 0;
@@ -48,16 +51,24 @@ static __initdata struct console early_shadow_console = {
 	.device = 0,
 };
 
-__init void enable_shadow_console(void)
+__init int shadow_console_enabled(void)
+{
+	return early_shadow_console.flags & CON_ENABLED;
+}
+
+__init void mark_shadow_error(void)
 {
 	int *loc = (int *)SHADOW_CONSOLE_MAGIC_LOC;
+	loc[0] = SHADOW_CONSOLE_MAGIC;
+	loc[1] = SHADOW_CONSOLE_START;
+}
 
-	if (!(early_shadow_console.flags & CON_ENABLED)) {
+__init void enable_shadow_console(void)
+{
+	if (!shadow_console_enabled()) {
 		register_console(&early_shadow_console);
 		/* for now, assume things are going to fail */
-		*loc = SHADOW_CONSOLE_MAGIC;
-		loc++;
-		*loc = SHADOW_CONSOLE_START;
+		mark_shadow_error();
 	}
 }
 
@@ -71,8 +82,32 @@ static __init int disable_shadow_console(void)
 	 */
 	int *loc = (int *)SHADOW_CONSOLE_MAGIC_LOC;
 
-	*loc = 0;
+	loc[0] = 0;
 
 	return 0;
 }
 pure_initcall(disable_shadow_console);
+
+/*
+ * since we can't use printk, dump numbers (as hex), n = # bits
+ */
+__init void early_shadow_reg(unsigned long reg, unsigned int n)
+{
+	/*
+	 * can't use any "normal" kernel features, since thay
+	 * may not be relocated to their execute address yet
+	 */
+	int i;
+	char ascii[11] = " 0x";
+
+	n = n / 4;
+	reg = reg << ((8 - n) * 4);
+	n += 3;
+
+	for (i = 3; i <= n ; i++) {
+		ascii[i] = hex_asc_lo(reg >> 28);
+		reg <<= 4;
+	}
+	early_shadow_write(NULL, ascii, n);
+
+}
diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S
index f826f6b..6691012 100644
--- a/arch/blackfin/mach-common/head.S
+++ b/arch/blackfin/mach-common/head.S
@@ -153,6 +153,8 @@ ENTRY(__start)
 
 #ifdef CONFIG_EARLY_PRINTK
 	call _init_early_exception_vectors;
+	r0 = (EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU);
+	sti r0;
 #endif
 
 	r0 = 0 (x);
@@ -212,12 +214,21 @@ ENTRY(__start)
 	[p0] = p1;
 	csync;
 
+#ifdef CONFIG_EARLY_PRINTK
+	r0 = (EVT_IVG15 | EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU) (z);
+#else
 	r0 = EVT_IVG15 (z);
+#endif
 	sti r0;
 
 	raise 15;
+#ifdef CONFIG_EARLY_PRINTK
+	p0.l = _early_trap;
+	p0.h = _early_trap;
+#else
 	p0.l = .LWAIT_HERE;
 	p0.h = .LWAIT_HERE;
+#endif
 	reti = p0;
 #if ANOMALY_05000281
 	nop; nop; nop;
diff --git a/arch/blackfin/mm/init.c b/arch/blackfin/mm/init.c
index 68bd0bd..b88ce7f 100644
--- a/arch/blackfin/mm/init.c
+++ b/arch/blackfin/mm/init.c
@@ -33,6 +33,7 @@
 #include <asm/bfin-global.h>
 #include <asm/pda.h>
 #include <asm/cplbinit.h>
+#include <asm/early_printk.h>
 #include "blackfin_sram.h"
 
 /*
@@ -113,6 +114,8 @@ asmlinkage void __init init_pda(void)
 {
 	unsigned int cpu = raw_smp_processor_id();
 
+	early_shadow_stamp();
+
 	/* Initialize the PDA fields holding references to other parts
 	   of the memory. The content of such memory is still
 	   undefined at the time of the call, we are only setting up
-- 
1.6.4.2

[PATCH 29/72] Blackfin: fix BF548 UART0 DMA IRQ translation

[Mike Frysinger]

From: Stefan Pledl <stefan.pledl@mesutronic.de>

The initial BF54x port included some defines to keep code simple across
different processors, but it just ended up causing the UART0 DMA IRQs to
be set to the UART1 channels.

Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf548/dma.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/mach-bf548/dma.c b/arch/blackfin/mach-bf548/dma.c
index 5359806..d9239bc 100644
--- a/arch/blackfin/mach-bf548/dma.c
+++ b/arch/blackfin/mach-bf548/dma.c
@@ -91,16 +91,16 @@ int channel2irq(unsigned int channel)
 		ret_irq = IRQ_SPI1;
 		break;
 	case CH_UART0_RX:
-		ret_irq = IRQ_UART_RX;
+		ret_irq = IRQ_UART0_RX;
 		break;
 	case CH_UART0_TX:
-		ret_irq = IRQ_UART_TX;
+		ret_irq = IRQ_UART0_TX;
 		break;
 	case CH_UART1_RX:
-		ret_irq = IRQ_UART_RX;
+		ret_irq = IRQ_UART1_RX;
 		break;
 	case CH_UART1_TX:
-		ret_irq = IRQ_UART_TX;
+		ret_irq = IRQ_UART1_TX;
 		break;
 	case CH_EPPI0:
 		ret_irq = IRQ_EPPI0;
-- 
1.6.4.2

[PATCH 30/72] Blackfin: bf538: add bfin_clear_PPI_STATUS() helper

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

Add the bf538 version of bfin_clear_PPI_STATUS() to match all other ports.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf538/include/mach/cdefBF538.h |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf538/include/mach/cdefBF538.h b/arch/blackfin/mach-bf538/include/mach/cdefBF538.h
index 99ca3f4..1de6751 100644
--- a/arch/blackfin/mach-bf538/include/mach/cdefBF538.h
+++ b/arch/blackfin/mach-bf538/include/mach/cdefBF538.h
@@ -1310,6 +1310,7 @@
 #define bfin_write_PPI_CONTROL(val)    bfin_write16(PPI_CONTROL, val)
 #define bfin_read_PPI_STATUS()         bfin_read16(PPI_STATUS)
 #define bfin_write_PPI_STATUS(val)     bfin_write16(PPI_STATUS, val)
+#define bfin_clear_PPI_STATUS()        bfin_read_PPI_STATUS()
 #define bfin_read_PPI_DELAY()          bfin_read16(PPI_DELAY)
 #define bfin_write_PPI_DELAY(val)      bfin_write16(PPI_DELAY, val)
 #define bfin_read_PPI_COUNT()          bfin_read16(PPI_COUNT)
-- 
1.6.4.2

[PATCH 31/72] Blackfin: bf533-stamp: add resources for mmc_spi card

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf533/boards/stamp.c |   40 +++++++++++++++++++++++++++++++
 1 files changed, 40 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 42d4c9f..e6548a6 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -35,6 +35,7 @@
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
+#include <linux/spi/mmc_spi.h>
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 #include <linux/usb/isp1362.h>
 #endif
@@ -223,6 +224,34 @@ static struct bfin5xx_spi_chip spidev_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+#define MMC_SPI_CARD_DETECT_INT IRQ_PF5
+static int bfin_mmc_spi_init(struct device *dev,
+	irqreturn_t (*detect_int)(int, void *), void *data)
+{
+	return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int,
+		IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+		"mmc-spi-detect", data);
+}
+
+static void bfin_mmc_spi_exit(struct device *dev, void *data)
+{
+	free_irq(MMC_SPI_CARD_DETECT_INT, data);
+}
+
+static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
+	.init = bfin_mmc_spi_init,
+	.exit = bfin_mmc_spi_exit,
+	.detect_delay = 100, /* msecs */
+};
+
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+	.pio_interrupt = 0,
+};
+#endif
+
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
 	{
@@ -286,6 +315,17 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &spidev_chip_info,
 	},
 #endif
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 4,
+		.platform_data = &bfin_mmc_spi_pdata,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
 };
 
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-- 
1.6.4.2

[PATCH 32/72] Blackfin: do not try displaying the end of the stack

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

The end of the stack may not be valid (and that could be OK), so do not
attempt to parse it.  If we do, we might use a bad pointer in kernel space
which makes things panic().

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/traps.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 519acca..18c6cd4 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -911,7 +911,7 @@ void show_stack(struct task_struct *task, unsigned long *stack)
 		frame_no = 0;
 
 		for (addr = (unsigned int *)((unsigned int)stack & ~0xF), i = 0;
-		     addr <= endstack; addr++, i++) {
+		     addr < endstack; addr++, i++) {
 
 			ret_addr = 0;
 			if (!j && i % 8 == 0)
-- 
1.6.4.2

[PATCH 33/72] Blackfin: bf537-stamp: update AD714x resources

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

Push the device table to the board resources as data interpretation can be
changed on a per-board basis.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |  133 ++++++++++++++++++++++++++++++-
 1 files changed, 131 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 72d11de..e5fffe7 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -540,6 +540,120 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
 
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+
+static struct ad714x_slider_plat slider_plat[] = {
+	{
+		.start_stage = 0,
+		.end_stage = 7,
+		.max_coord = 128,
+	},
+};
+
+static struct ad714x_button_plat button_plat[] = {
+	{
+		.keycode = BTN_FORWARD,
+		.l_mask = 0,
+		.h_mask = 0x600,
+	},
+	{
+		.keycode = BTN_LEFT,
+		.l_mask = 0,
+		.h_mask = 0x500,
+	},
+	{
+		.keycode = BTN_MIDDLE,
+		.l_mask = 0,
+		.h_mask = 0x800,
+	},
+	{
+		.keycode = BTN_RIGHT,
+		.l_mask = 0x100,
+		.h_mask = 0x400,
+	},
+	{
+		.keycode = BTN_BACK,
+		.l_mask = 0x200,
+		.h_mask = 0x400,
+	},
+};
+static struct ad714x_platform_data ad7147_platfrom_data = {
+	.slider_num = 1,
+	.button_num = 5,
+	.slider = slider_plat,
+	.button = button_plat,
+	.stage_cfg_reg =  {
+		{0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+		{0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
+		{0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
+		{0xFF7B, 0x3FFF, 0x506,  0x2626, 1100, 1100, 1150, 1150},
+		{0xFDFE, 0x3FFF, 0x606,  0x2626, 1100, 1100, 1150, 1150},
+		{0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
+		{0xFFEF, 0x1FFF, 0x0,    0x2626, 1100, 1100, 1150, 1150},
+	},
+	.sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
+};
+#endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
+#include <linux/input.h>
+#include <linux/input/ad714x.h>
+static struct ad714x_button_plat button_plat[] = {
+	{
+		.keycode = BTN_1,
+		.l_mask = 0,
+		.h_mask = 0x1,
+	},
+	{
+		.keycode = BTN_2,
+		.l_mask = 0,
+		.h_mask = 0x2,
+	},
+	{
+		.keycode = BTN_3,
+		.l_mask = 0,
+		.h_mask = 0x4,
+	},
+	{
+		.keycode = BTN_4,
+		.l_mask = 0x0,
+		.h_mask = 0x8,
+	},
+};
+static struct ad714x_platform_data ad7142_platfrom_data = {
+	.button_num = 4,
+	.button = button_plat,
+	.stage_cfg_reg =  {
+		/* fixme: figure out right setting for all comoponent according
+		 * to hardware feature of EVAL-AD7142EB board */
+		{0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+		{0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+		{0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+		{0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+		{0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
+	},
+	.sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
+};
+#endif
+
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 
@@ -784,6 +898,20 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad9960_spi_chip_info,
 	},
 #endif
+
+#if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
+	{
+		.modalias = "ad714x_captouch",
+		.max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
+		.irq = IRQ_PF4,
+		.bus_num = 0,
+		.chip_select = 5,
+		.mode = SPI_MODE_3,
+		.platform_data = &ad7147_platfrom_data,
+		.controller_data = &ad7147_spi_chip_info,
+	},
+#endif
+
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -1337,10 +1465,11 @@ static struct adp5520_platform_data adp5520_pdev_data = {
 #endif
 
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
-#if defined(CONFIG_JOYSTICK_AD7142) || defined(CONFIG_JOYSTICK_AD7142_MODULE)
+#if defined(CONFIG_INPUT_EVAL_AD7142EB)
 	{
-		I2C_BOARD_INFO("ad7142_joystick", 0x2C),
+		I2C_BOARD_INFO("ad7142_captouch", 0x2C),
 		.irq = IRQ_PG5,
+		.platform_data = (void *)&ad7142_platfrom_data,
 	},
 #endif
 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
-- 
1.6.4.2

[PATCH 34/72] Blackfin: clean up duplicate I2C device type definitions

[Mike Frysinger]

From: Jean Delvare <khali@linux-fr.org>

I2C_BOARD_INFO() already sets .type, no need to set it again.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf527/boards/cm_bf527.c |    2 --
 1 files changed, 0 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 3a62066..85f9ac5 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -796,13 +796,11 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_lcd", 0x22),
-		.type = "pcf8574_lcd",
 	},
 #endif
 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 	{
 		I2C_BOARD_INFO("pcf8574_keypad", 0x27),
-		.type = "pcf8574_keypad",
 		.irq = IRQ_PF8,
 	},
 #endif
-- 
1.6.4.2

[PATCH 35/72] Blackfin: fix MPU handling of invalid memory accesses

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

The protect_page() function was incorrectly setting up the hardware tables
based on possible access capabilities rather than the actual requested
values.  This means we would grant more access to mmap-ed pages than we
should have.  Once we fix this, we need to tweak the signal generated by
such accesses to aline ourselves with other ports.  This allows the LTP
mmap0{5,6,7} cases to run properly.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/mmu_context.h |    6 +++---
 arch/blackfin/kernel/traps.c            |    2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/include/asm/mmu_context.h b/arch/blackfin/include/asm/mmu_context.h
index 944e29f..040410b 100644
--- a/arch/blackfin/include/asm/mmu_context.h
+++ b/arch/blackfin/include/asm/mmu_context.h
@@ -127,17 +127,17 @@ static inline void protect_page(struct mm_struct *mm, unsigned long addr,
 	unsigned long idx = page >> 5;
 	unsigned long bit = 1 << (page & 31);
 
-	if (flags & VM_MAYREAD)
+	if (flags & VM_READ)
 		mask[idx] |= bit;
 	else
 		mask[idx] &= ~bit;
 	mask += page_mask_nelts;
-	if (flags & VM_MAYWRITE)
+	if (flags & VM_WRITE)
 		mask[idx] |= bit;
 	else
 		mask[idx] &= ~bit;
 	mask += page_mask_nelts;
-	if (flags & VM_MAYEXEC)
+	if (flags & VM_EXEC)
 		mask[idx] |= bit;
 	else
 		mask[idx] &= ~bit;
diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 18c6cd4..644e35e 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -411,7 +411,7 @@ asmlinkage void trap_c(struct pt_regs *fp)
 	/* 0x23 - Data CPLB protection violation, handled here */
 	case VEC_CPLB_VL:
 		info.si_code = ILL_CPLB_VI;
-		sig = SIGBUS;
+		sig = SIGSEGV;
 		strerror = KERN_NOTICE EXC_0x23(KERN_NOTICE);
 		CHK_DEBUGGER_TRAP_MAYBE();
 		break;
-- 
1.6.4.2

[PATCH 36/72] Blackfin: bf533-stamp: fix typo in SPI frequency for ad1836 codec

[Mike Frysinger]

From: Cliff Cai <cliff.cai@analog.com>

One too many zeros means we run way faster than the codec can handle.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf533/boards/stamp.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index e6548a6..7a7b656 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -280,7 +280,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
 		.modalias = "ad1836-spi",
-		.max_speed_hz = 31250000,     /* max spi clock (SCK) speed in HZ */
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
 		.controller_data = &ad1836_spi_chip_info,
-- 
1.6.4.2

[PATCH 37/72] Blackfin: improve double fault debug handling

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

Since the hardware only provides reporting for the last exception handled,
and the values are valid only when executing the exception handler, we
need to save the context for reporting at a later point.  While we do this
for one exception, it doesn't work properly when handling a second one as
the original exception is clobbered by the double fault.  So when double
fault debugging is enabled, create a dedicated shadow of these values and
save/restore out of there.  Now the crash report properly displays the
first exception as well as the second one.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/pda.h      |    6 ++++++
 arch/blackfin/kernel/asm-offsets.c   |    6 ++++++
 arch/blackfin/kernel/traps.c         |    8 ++++----
 arch/blackfin/mach-bf561/secondary.S |    8 ++++----
 arch/blackfin/mach-common/entry.S    |   22 +++++++++++++---------
 arch/blackfin/mach-common/head.S     |    8 ++++----
 6 files changed, 37 insertions(+), 21 deletions(-)

diff --git a/arch/blackfin/include/asm/pda.h b/arch/blackfin/include/asm/pda.h
index 69b96b4..a6f9569 100644
--- a/arch/blackfin/include/asm/pda.h
+++ b/arch/blackfin/include/asm/pda.h
@@ -61,6 +61,12 @@ struct blackfin_pda {			/* Per-processor Data Area */
 	unsigned long retx;
 	unsigned long seqstat;
 	unsigned int __nmi_count;	/* number of times NMI asserted on this CPU */
+#ifdef CONFIG_DEBUG_DOUBLEFAULT
+	unsigned long dcplb_doublefault_addr;
+	unsigned long icplb_doublefault_addr;
+	unsigned long retx_doublefault;
+	unsigned long seqstat_doublefault;
+#endif
 };
 
 extern struct blackfin_pda cpu_pda[];
diff --git a/arch/blackfin/kernel/asm-offsets.c b/arch/blackfin/kernel/asm-offsets.c
index 8ad4f2c..f05d1b9 100644
--- a/arch/blackfin/kernel/asm-offsets.c
+++ b/arch/blackfin/kernel/asm-offsets.c
@@ -153,6 +153,12 @@ int main(void)
 	DEFINE(PDA_ICPLB, offsetof(struct blackfin_pda, icplb_fault_addr));
 	DEFINE(PDA_RETX, offsetof(struct blackfin_pda, retx));
 	DEFINE(PDA_SEQSTAT, offsetof(struct blackfin_pda, seqstat));
+#ifdef CONFIG_DEBUG_DOUBLEFAULT
+	DEFINE(PDA_DF_DCPLB, offsetof(struct blackfin_pda, dcplb_doublefault_addr));
+	DEFINE(PDA_DF_ICPLB, offsetof(struct blackfin_pda, icplb_doublefault_addr));
+	DEFINE(PDA_DF_SEQSTAT, offsetof(struct blackfin_pda, seqstat_doublefault));
+	DEFINE(PDA_DF_RETX, offsetof(struct blackfin_pda, retx_doublefault));
+#endif
 #ifdef CONFIG_SMP
 	/* Inter-core lock (in L2 SRAM) */
 	DEFINE(SIZEOF_CORELOCK, sizeof(struct corelock_slot));
diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 644e35e..0904430 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -229,12 +229,12 @@ asmlinkage void double_fault_c(struct pt_regs *fp)
 	if (((long)fp->seqstat &  SEQSTAT_EXCAUSE) == VEC_UNCOV) {
 		unsigned int cpu = smp_processor_id();
 		char buf[150];
-		decode_address(buf, cpu_pda[cpu].retx);
+		decode_address(buf, cpu_pda[cpu].retx_doublefault);
 		printk(KERN_EMERG "While handling exception (EXCAUSE = 0x%x) at %s:\n",
-			(unsigned int)cpu_pda[cpu].seqstat & SEQSTAT_EXCAUSE, buf);
-		decode_address(buf, cpu_pda[cpu].dcplb_fault_addr);
+			(unsigned int)cpu_pda[cpu].seqstat_doublefault & SEQSTAT_EXCAUSE, buf);
+		decode_address(buf, cpu_pda[cpu].dcplb_doublefault_addr);
 		printk(KERN_NOTICE "   DCPLB_FAULT_ADDR: %s\n", buf);
-		decode_address(buf, cpu_pda[cpu].icplb_fault_addr);
+		decode_address(buf, cpu_pda[cpu].icplb_doublefault_addr);
 		printk(KERN_NOTICE "   ICPLB_FAULT_ADDR: %s\n", buf);
 
 		decode_address(buf, fp->retx);
diff --git a/arch/blackfin/mach-bf561/secondary.S b/arch/blackfin/mach-bf561/secondary.S
index 35280f0..097550f 100644
--- a/arch/blackfin/mach-bf561/secondary.S
+++ b/arch/blackfin/mach-bf561/secondary.S
@@ -126,22 +126,22 @@ ENTRY(_coreb_trampoline_start)
 	 * below
 	 */
 	GET_PDA(p0, r0);
-	r7 = [p0 + PDA_RETX];
+	r7 = [p0 + PDA_DF_RETX];
 	p1.l = _init_saved_retx_coreb;
 	p1.h = _init_saved_retx_coreb;
 	[p1] = r7;
 
-	r7 = [p0 + PDA_DCPLB];
+	r7 = [p0 + PDA_DF_DCPLB];
 	p1.l = _init_saved_dcplb_fault_addr_coreb;
 	p1.h = _init_saved_dcplb_fault_addr_coreb;
 	[p1] = r7;
 
-	r7 = [p0 + PDA_ICPLB];
+	r7 = [p0 + PDA_DF_ICPLB];
 	p1.l = _init_saved_icplb_fault_addr_coreb;
 	p1.h = _init_saved_icplb_fault_addr_coreb;
 	[p1] = r7;
 
-	r7 = [p0 + PDA_SEQSTAT];
+	r7 = [p0 + PDA_DF_SEQSTAT];
 	p1.l = _init_saved_seqstat_coreb;
 	p1.h = _init_saved_seqstat_coreb;
 	[p1] = r7;
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index cbc5b6d..4e8e3fe 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -326,8 +326,6 @@ ENTRY(_ex_trap_c)
 	[p4] = r7;
 	csync;
 
-#ifndef CONFIG_DEBUG_DOUBLEFAULT
-
 	/*
 	 * Save these registers, as they are only valid in exception context
 	 *  (where we are now - as soon as we defer to IRQ5, they can change)
@@ -347,7 +345,10 @@ ENTRY(_ex_trap_c)
 
 	r6 = retx;
 	[p5 + PDA_RETX] = r6;
-#endif
+
+	r6 = SEQSTAT;
+	[p5 + PDA_SEQSTAT] = r6;
+
 	/* Save the state of single stepping */
 	r6 = SYSCFG;
 	[p5 + PDA_SYSCFG] = r6;
@@ -444,6 +445,9 @@ ENTRY(_exception_to_level5)
 	r6 = [p5 + PDA_SYSCFG];
 	[sp + PT_SYSCFG] = r6;
 
+	r6 = [p5 + PDA_SEQSTAT]; /* Read back seqstat */
+	[sp + PT_SEQSTAT] = r6;
+
 	/* Restore the hardware error vector.  */
 	r7.h = _evt_ivhw;
 	r7.l = _evt_ivhw;
@@ -496,7 +500,7 @@ ENTRY(_trap) /* Exception: 4th entry into system event table(supervisor mode)*/
 	 */
 	EX_SCRATCH_REG = sp;
 	GET_PDA_SAFE(sp);
-	sp = [sp + PDA_EXSTACK]
+	sp = [sp + PDA_EXSTACK];
 	/* Try to deal with syscalls quickly.  */
 	[--sp] = ASTAT;
 	[--sp] = (R7:6,P5:4);
@@ -532,18 +536,18 @@ ENTRY(_trap) /* Exception: 4th entry into system event table(supervisor mode)*/
 	p4.l = lo(DCPLB_FAULT_ADDR);
 	p4.h = hi(DCPLB_FAULT_ADDR);
 	r7 = [p4];
-	[p5 + PDA_DCPLB] = r7;
+	[p5 + PDA_DF_DCPLB] = r7;
 
 	p4.l = lo(ICPLB_FAULT_ADDR);
 	p4.h = hi(ICPLB_FAULT_ADDR);
 	r7 = [p4];
-	[p5 + PDA_ICPLB] = r7;
+	[p5 + PDA_DF_ICPLB] = r7;
 
-	r6 = retx;
-	[p5 + PDA_RETX] = r6;
+	r7 = retx;
+	[p5 + PDA_DF_RETX] = r7;
 
 	r7 = SEQSTAT;		/* reason code is in bit 5:0 */
-	[p5 + PDA_SEQSTAT] = r7;
+	[p5 + PDA_DF_SEQSTAT] = r7;
 #else
 	r7 = SEQSTAT;           /* reason code is in bit 5:0 */
 #endif
diff --git a/arch/blackfin/mach-common/head.S b/arch/blackfin/mach-common/head.S
index 6691012..9c79dfe 100644
--- a/arch/blackfin/mach-common/head.S
+++ b/arch/blackfin/mach-common/head.S
@@ -124,22 +124,22 @@ ENTRY(__start)
 	 * below
 	 */
 	GET_PDA(p0, r0);
-	r6 = [p0 + PDA_RETX];
+	r6 = [p0 + PDA_DF_RETX];
 	p1.l = _init_saved_retx;
 	p1.h = _init_saved_retx;
 	[p1] = r6;
 
-	r6 = [p0 + PDA_DCPLB];
+	r6 = [p0 + PDA_DF_DCPLB];
 	p1.l = _init_saved_dcplb_fault_addr;
 	p1.h = _init_saved_dcplb_fault_addr;
 	[p1] = r6;
 
-	r6 = [p0 + PDA_ICPLB];
+	r6 = [p0 + PDA_DF_ICPLB];
 	p1.l = _init_saved_icplb_fault_addr;
 	p1.h = _init_saved_icplb_fault_addr;
 	[p1] = r6;
 
-	r6 = [p0 + PDA_SEQSTAT];
+	r6 = [p0 + PDA_DF_SEQSTAT];
 	p1.l = _init_saved_seqstat;
 	p1.h = _init_saved_seqstat;
 	[p1] = r6;
-- 
1.6.4.2

[PATCH 38/72] Blackfin: bf537-stamp: drop ATA interrupt probe workaround

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

The interrupt probe workaround doesn't work without hacks to common code,
and the add-on card only needs a simple resistor to fix the problem, so
drop the board-specific hack.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |    5 -----
 1 files changed, 0 insertions(+), 5 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index e5fffe7..192e34e 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -1728,11 +1728,6 @@ static int __init stamp_init(void)
 	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 
-#if (defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)) \
-	 && defined(PATA_INT)
-	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
-#endif
-
 	return 0;
 }
 
-- 
1.6.4.2

[PATCH 39/72] Blackfin: convert boards to use platform data with smc91x

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

Latest smc91x driver allows you to specify settings in board resources
rather than needing CONFIG_BLACKFIN in the drivers/net/smc91x.h header.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf527/boards/cm_bf527.c   |   11 +++++++++++
 arch/blackfin/mach-bf527/boards/ezkit.c      |   11 +++++++++++
 arch/blackfin/mach-bf533/boards/H8606.c      |   11 +++++++++++
 arch/blackfin/mach-bf533/boards/blackstamp.c |   11 +++++++++++
 arch/blackfin/mach-bf533/boards/cm_bf533.c   |   11 +++++++++++
 arch/blackfin/mach-bf533/boards/ezkit.c      |   11 +++++++++++
 arch/blackfin/mach-bf533/boards/stamp.c      |   11 +++++++++++
 arch/blackfin/mach-bf537/boards/cm_bf537.c   |   11 +++++++++++
 arch/blackfin/mach-bf537/boards/pnav10.c     |   11 +++++++++++
 arch/blackfin/mach-bf537/boards/stamp.c      |   11 +++++++++++
 arch/blackfin/mach-bf537/boards/tcm_bf537.c  |   11 +++++++++++
 arch/blackfin/mach-bf538/boards/ezkit.c      |   11 +++++++++++
 arch/blackfin/mach-bf561/boards/cm_bf561.c   |   10 ++++++++++
 arch/blackfin/mach-bf561/boards/ezkit.c      |   11 +++++++++++
 14 files changed, 153 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 85f9ac5..cb360e9 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -275,6 +275,14 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -293,6 +301,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index b843d0e..617a287 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -292,6 +292,14 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -310,6 +318,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 38cf8ff..1bd8b61 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -88,6 +88,14 @@ static struct platform_device dm9000_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -110,6 +118,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c
index 9ecdc36..8208d67 100644
--- a/arch/blackfin/mach-bf533/boards/blackstamp.c
+++ b/arch/blackfin/mach-bf533/boards/blackstamp.c
@@ -48,6 +48,14 @@ static struct platform_device rtc_device = {
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -66,6 +74,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 1443e92..7052568 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -195,6 +195,14 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.start = 0x20200300,
@@ -211,6 +219,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index 4e3e511..88b2dfc 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -67,6 +67,14 @@ static struct platform_device bfin_fb_adv7393_device = {
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -84,6 +92,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 7a7b656..f3dc283 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -63,6 +63,14 @@ static struct platform_device rtc_device = {
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -81,6 +89,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 2a87d1c..3681d2c 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -223,6 +223,14 @@ static struct platform_device hitachi_fb_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.start = 0x20200300,
@@ -240,6 +248,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 838240f..3bbe102 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -92,6 +92,14 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -110,6 +118,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 192e34e..313249e 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -171,6 +171,14 @@ static struct platform_device rtc_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -189,6 +197,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index e523e6e..97a86b4 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -223,6 +223,14 @@ static struct platform_device hitachi_fb_device = {
 #endif
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.start = 0x20200300,
@@ -240,6 +248,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf538/boards/ezkit.c b/arch/blackfin/mach-bf538/boards/ezkit.c
index 57695b4..42297fa 100644
--- a/arch/blackfin/mach-bf538/boards/ezkit.c
+++ b/arch/blackfin/mach-bf538/boards/ezkit.c
@@ -177,6 +177,14 @@ static struct platform_device bfin_sir2_device = {
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -194,6 +202,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 0c9d72c..ebb0755 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -213,6 +213,13 @@ static struct platform_device hitachi_fb_device = {
 
 
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
 
 static struct resource smc91x_resources[] = {
 	{
@@ -231,6 +238,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 4df904f..10edc99 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -147,6 +147,14 @@ static struct platform_device net2272_bfin_device = {
  *  Driver needs to know address, irq and flag pin.
  */
 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
 static struct resource smc91x_resources[] = {
 	{
 		.name = "smc91x-regs",
@@ -166,6 +174,9 @@ static struct platform_device smc91x_device = {
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
 };
 #endif
 
-- 
1.6.4.2

[PATCH 40/72] Blackfin: drop unused MMR defines that only cause bad code to be written

[Mike Frysinger]

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf518/include/mach/blackfin.h |   10 ---
 arch/blackfin/mach-bf527/include/mach/blackfin.h |   10 ---
 arch/blackfin/mach-bf533/dma.c                   |    8 +-
 arch/blackfin/mach-bf533/include/mach/blackfin.h |    7 --
 arch/blackfin/mach-bf537/dma.c                   |    8 +-
 arch/blackfin/mach-bf537/include/mach/blackfin.h |   90 ----------------------
 arch/blackfin/mach-bf538/include/mach/blackfin.h |   10 ---
 arch/blackfin/mach-bf548/include/mach/blackfin.h |   89 ---------------------
 8 files changed, 8 insertions(+), 224 deletions(-)

diff --git a/arch/blackfin/mach-bf518/include/mach/blackfin.h b/arch/blackfin/mach-bf518/include/mach/blackfin.h
index e8e14c2..83421d3 100644
--- a/arch/blackfin/mach-bf518/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf518/include/mach/blackfin.h
@@ -68,11 +68,6 @@
 #endif
 #endif
 
-/* UART_IIR Register */
-#define STATUS(x)	((x << 1) & 0x06)
-#define STATUS_P1	0x02
-#define STATUS_P0	0x01
-
 #define BFIN_UART_NR_PORTS	2
 
 #define OFFSET_THR              0x00	/* Transmit Holding register            */
@@ -88,11 +83,6 @@
 #define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
 #define OFFSET_GCTL             0x24	/* Global Control Register              */
 
-/* DPMC*/
-#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
-#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
-#define STOPCK_OFF STOPCK
-
 /* PLL_DIV Masks													*/
 #define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
 #define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
diff --git a/arch/blackfin/mach-bf527/include/mach/blackfin.h b/arch/blackfin/mach-bf527/include/mach/blackfin.h
index 03665a8..ea9cb0f 100644
--- a/arch/blackfin/mach-bf527/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf527/include/mach/blackfin.h
@@ -56,11 +56,6 @@
 #endif
 #endif
 
-/* UART_IIR Register */
-#define STATUS(x)	((x << 1) & 0x06)
-#define STATUS_P1	0x02
-#define STATUS_P0	0x01
-
 #define BFIN_UART_NR_PORTS	2
 
 #define OFFSET_THR              0x00	/* Transmit Holding register            */
@@ -76,11 +71,6 @@
 #define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
 #define OFFSET_GCTL             0x24	/* Global Control Register              */
 
-/* DPMC*/
-#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
-#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
-#define STOPCK_OFF STOPCK
-
 /* PLL_DIV Masks													*/
 #define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
 #define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
diff --git a/arch/blackfin/mach-bf533/dma.c b/arch/blackfin/mach-bf533/dma.c
index 0a6eb8f..7a443c3 100644
--- a/arch/blackfin/mach-bf533/dma.c
+++ b/arch/blackfin/mach-bf533/dma.c
@@ -76,12 +76,12 @@ int channel2irq(unsigned int channel)
 		ret_irq = IRQ_SPI;
 		break;
 
-	case CH_UART_RX:
-		ret_irq = IRQ_UART_RX;
+	case CH_UART0_RX:
+		ret_irq = IRQ_UART0_RX;
 		break;
 
-	case CH_UART_TX:
-		ret_irq = IRQ_UART_TX;
+	case CH_UART0_TX:
+		ret_irq = IRQ_UART0_TX;
 		break;
 
 	case CH_MEM_STREAM0_SRC:
diff --git a/arch/blackfin/mach-bf533/include/mach/blackfin.h b/arch/blackfin/mach-bf533/include/mach/blackfin.h
index 39aa175..499e897 100644
--- a/arch/blackfin/mach-bf533/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf533/include/mach/blackfin.h
@@ -43,13 +43,6 @@
 
 #define BFIN_UART_NR_PORTS      1
 
-#define CH_UART_RX CH_UART0_RX
-#define CH_UART_TX CH_UART0_TX
-
-#define IRQ_UART_ERROR IRQ_UART0_ERROR
-#define IRQ_UART_RX    IRQ_UART0_RX
-#define IRQ_UART_TX    IRQ_UART0_TX
-
 #define OFFSET_THR              0x00	/* Transmit Holding register            */
 #define OFFSET_RBR              0x00	/* Receive Buffer register              */
 #define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
diff --git a/arch/blackfin/mach-bf537/dma.c b/arch/blackfin/mach-bf537/dma.c
index 8118505..d23fc0e 100644
--- a/arch/blackfin/mach-bf537/dma.c
+++ b/arch/blackfin/mach-bf537/dma.c
@@ -96,12 +96,12 @@ int channel2irq(unsigned int channel)
 		ret_irq = IRQ_SPI;
 		break;
 
-	case CH_UART_RX:
-		ret_irq = IRQ_UART_RX;
+	case CH_UART0_RX:
+		ret_irq = IRQ_UART0_RX;
 		break;
 
-	case CH_UART_TX:
-		ret_irq = IRQ_UART_TX;
+	case CH_UART0_TX:
+		ret_irq = IRQ_UART0_TX;
 		break;
 
 	case CH_MEM_STREAM0_SRC:
diff --git a/arch/blackfin/mach-bf537/include/mach/blackfin.h b/arch/blackfin/mach-bf537/include/mach/blackfin.h
index f5e5015..9ee8834 100644
--- a/arch/blackfin/mach-bf537/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf537/include/mach/blackfin.h
@@ -45,96 +45,11 @@
 #if !defined(__ASSEMBLY__)
 #include "cdefBF534.h"
 
-/* UART 0*/
-#define bfin_read_UART_THR() bfin_read_UART0_THR()
-#define bfin_write_UART_THR(val) bfin_write_UART0_THR(val)
-#define bfin_read_UART_RBR() bfin_read_UART0_RBR()
-#define bfin_write_UART_RBR(val) bfin_write_UART0_RBR(val)
-#define bfin_read_UART_DLL() bfin_read_UART0_DLL()
-#define bfin_write_UART_DLL(val) bfin_write_UART0_DLL(val)
-#define bfin_read_UART_IER() bfin_read_UART0_IER()
-#define bfin_write_UART_IER(val) bfin_write_UART0_IER(val)
-#define bfin_read_UART_DLH() bfin_read_UART0_DLH()
-#define bfin_write_UART_DLH(val) bfin_write_UART0_DLH(val)
-#define bfin_read_UART_IIR() bfin_read_UART0_IIR()
-#define bfin_write_UART_IIR(val) bfin_write_UART0_IIR(val)
-#define bfin_read_UART_LCR() bfin_read_UART0_LCR()
-#define bfin_write_UART_LCR(val) bfin_write_UART0_LCR(val)
-#define bfin_read_UART_MCR() bfin_read_UART0_MCR()
-#define bfin_write_UART_MCR(val) bfin_write_UART0_MCR(val)
-#define bfin_read_UART_LSR() bfin_read_UART0_LSR()
-#define bfin_write_UART_LSR(val) bfin_write_UART0_LSR(val)
-#define bfin_read_UART_SCR() bfin_read_UART0_SCR()
-#define bfin_write_UART_SCR(val) bfin_write_UART0_SCR(val)
-#define bfin_read_UART_GCTL() bfin_read_UART0_GCTL()
-#define bfin_write_UART_GCTL(val) bfin_write_UART0_GCTL(val)
-
 #if defined(CONFIG_BF537) || defined(CONFIG_BF536)
 #include "cdefBF537.h"
 #endif
 #endif
 
-/* MAP used DEFINES from BF533 to BF537 - so we don't need to change them in the driver, kernel, etc. */
-
-/* UART_IIR Register */
-#define STATUS(x)	((x << 1) & 0x06)
-#define STATUS_P1	0x02
-#define STATUS_P0	0x01
-
-/* DMA Channel */
-#define bfin_read_CH_UART_RX() bfin_read_CH_UART0_RX()
-#define bfin_write_CH_UART_RX(val) bfin_write_CH_UART0_RX(val)
-#define CH_UART_RX CH_UART0_RX
-#define bfin_read_CH_UART_TX() bfin_read_CH_UART0_TX()
-#define bfin_write_CH_UART_TX(val) bfin_write_CH_UART0_TX(val)
-#define CH_UART_TX CH_UART0_TX
-
-/* System Interrupt Controller */
-#define bfin_read_IRQ_UART_RX() bfin_read_IRQ_UART0_RX()
-#define bfin_write_IRQ_UART_RX(val) bfin_write_IRQ_UART0_RX(val)
-#define IRQ_UART_RX IRQ_UART0_RX
-#define bfin_read_IRQ_UART_TX() bfin_read_IRQ_UART0_TX()
-#define bfin_write_IRQ_UART_TX(val) bfin_write_IRQ_UART0_TX(val)
-#define	IRQ_UART_TX IRQ_UART0_TX
-#define bfin_read_IRQ_UART_ERROR() bfin_read_IRQ_UART0_ERROR()
-#define bfin_write_IRQ_UART_ERROR(val) bfin_write_IRQ_UART0_ERROR(val)
-#define	IRQ_UART_ERROR IRQ_UART0_ERROR
-
-/* MMR Registers*/
-#define bfin_read_UART_THR() bfin_read_UART0_THR()
-#define bfin_write_UART_THR(val) bfin_write_UART0_THR(val)
-#define BFIN_UART_THR UART0_THR
-#define bfin_read_UART_RBR() bfin_read_UART0_RBR()
-#define bfin_write_UART_RBR(val) bfin_write_UART0_RBR(val)
-#define BFIN_UART_RBR UART0_RBR
-#define bfin_read_UART_DLL() bfin_read_UART0_DLL()
-#define bfin_write_UART_DLL(val) bfin_write_UART0_DLL(val)
-#define BFIN_UART_DLL UART0_DLL
-#define bfin_read_UART_IER() bfin_read_UART0_IER()
-#define bfin_write_UART_IER(val) bfin_write_UART0_IER(val)
-#define BFIN_UART_IER UART0_IER
-#define bfin_read_UART_DLH() bfin_read_UART0_DLH()
-#define bfin_write_UART_DLH(val) bfin_write_UART0_DLH(val)
-#define BFIN_UART_DLH UART0_DLH
-#define bfin_read_UART_IIR() bfin_read_UART0_IIR()
-#define bfin_write_UART_IIR(val) bfin_write_UART0_IIR(val)
-#define BFIN_UART_IIR UART0_IIR
-#define bfin_read_UART_LCR() bfin_read_UART0_LCR()
-#define bfin_write_UART_LCR(val) bfin_write_UART0_LCR(val)
-#define BFIN_UART_LCR UART0_LCR
-#define bfin_read_UART_MCR() bfin_read_UART0_MCR()
-#define bfin_write_UART_MCR(val) bfin_write_UART0_MCR(val)
-#define BFIN_UART_MCR UART0_MCR
-#define bfin_read_UART_LSR() bfin_read_UART0_LSR()
-#define bfin_write_UART_LSR(val) bfin_write_UART0_LSR(val)
-#define BFIN_UART_LSR UART0_LSR
-#define bfin_read_UART_SCR() bfin_read_UART0_SCR()
-#define bfin_write_UART_SCR(val) bfin_write_UART0_SCR(val)
-#define BFIN_UART_SCR  UART0_SCR
-#define bfin_read_UART_GCTL() bfin_read_UART0_GCTL()
-#define bfin_write_UART_GCTL(val) bfin_write_UART0_GCTL(val)
-#define BFIN_UART_GCTL UART0_GCTL
-
 #define BFIN_UART_NR_PORTS	2
 
 #define OFFSET_THR              0x00	/* Transmit Holding register            */
@@ -150,11 +65,6 @@
 #define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
 #define OFFSET_GCTL             0x24	/* Global Control Register              */
 
-/* DPMC*/
-#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
-#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
-#define STOPCK_OFF STOPCK
-
 /* PLL_DIV Masks													*/
 #define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
 #define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
diff --git a/arch/blackfin/mach-bf538/include/mach/blackfin.h b/arch/blackfin/mach-bf538/include/mach/blackfin.h
index 9496196..5ecee16 100644
--- a/arch/blackfin/mach-bf538/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf538/include/mach/blackfin.h
@@ -47,11 +47,6 @@
 #endif
 #endif
 
-/* UART_IIR Register */
-#define STATUS(x)	((x << 1) & 0x06)
-#define STATUS_P1	0x02
-#define STATUS_P0	0x01
-
 #define BFIN_UART_NR_PORTS	3
 
 #define OFFSET_THR              0x00	/* Transmit Holding register            */
@@ -67,11 +62,6 @@
 #define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
 #define OFFSET_GCTL             0x24	/* Global Control Register              */
 
-/* DPMC*/
-#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
-#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
-#define STOPCK_OFF STOPCK
-
 /* PLL_DIV Masks													*/
 #define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
 #define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
diff --git a/arch/blackfin/mach-bf548/include/mach/blackfin.h b/arch/blackfin/mach-bf548/include/mach/blackfin.h
index 6b97396..318667b 100644
--- a/arch/blackfin/mach-bf548/include/mach/blackfin.h
+++ b/arch/blackfin/mach-bf548/include/mach/blackfin.h
@@ -72,97 +72,8 @@
 #include "cdefBF549.h"
 #endif
 
-/* UART 1*/
-#define bfin_read_UART_THR()		bfin_read_UART1_THR()
-#define bfin_write_UART_THR(val)	bfin_write_UART1_THR(val)
-#define bfin_read_UART_RBR()		bfin_read_UART1_RBR()
-#define bfin_write_UART_RBR(val)	bfin_write_UART1_RBR(val)
-#define bfin_read_UART_DLL()		bfin_read_UART1_DLL()
-#define bfin_write_UART_DLL(val)	bfin_write_UART1_DLL(val)
-#define bfin_read_UART_IER()		bfin_read_UART1_IER()
-#define bfin_write_UART_IER(val)	bfin_write_UART1_IER(val)
-#define bfin_read_UART_DLH()		bfin_read_UART1_DLH()
-#define bfin_write_UART_DLH(val)	bfin_write_UART1_DLH(val)
-#define bfin_read_UART_IIR()		bfin_read_UART1_IIR()
-#define bfin_write_UART_IIR(val)	bfin_write_UART1_IIR(val)
-#define bfin_read_UART_LCR()		bfin_read_UART1_LCR()
-#define bfin_write_UART_LCR(val)	bfin_write_UART1_LCR(val)
-#define bfin_read_UART_MCR()		bfin_read_UART1_MCR()
-#define bfin_write_UART_MCR(val)	bfin_write_UART1_MCR(val)
-#define bfin_read_UART_LSR()		bfin_read_UART1_LSR()
-#define bfin_write_UART_LSR(val)	bfin_write_UART1_LSR(val)
-#define bfin_read_UART_SCR()		bfin_read_UART1_SCR()
-#define bfin_write_UART_SCR(val)	bfin_write_UART1_SCR(val)
-#define bfin_read_UART_GCTL()		bfin_read_UART1_GCTL()
-#define bfin_write_UART_GCTL(val)	bfin_write_UART1_GCTL(val)
-
 #endif
 
-/* MAP used DEFINES from BF533 to BF54x - so we don't need to change 
- * them in the driver, kernel, etc. */
-
-/* UART_IIR Register */
-#define STATUS(x)	((x << 1) & 0x06)
-#define STATUS_P1	0x02
-#define STATUS_P0	0x01
-
-/* UART 0*/
-
-/* DMA Channel */
-#define bfin_read_CH_UART_RX()		bfin_read_CH_UART1_RX()
-#define bfin_write_CH_UART_RX(val)	bfin_write_CH_UART1_RX(val)
-#define bfin_read_CH_UART_TX()		bfin_read_CH_UART1_TX()
-#define bfin_write_CH_UART_TX(val)	bfin_write_CH_UART1_TX(val)
-#define CH_UART_RX			CH_UART1_RX
-#define CH_UART_TX			CH_UART1_TX
-
-/* System Interrupt Controller */
-#define bfin_read_IRQ_UART_RX()		bfin_read_IRQ_UART1_RX()
-#define bfin_write_IRQ_UART_RX(val)	bfin_write_IRQ_UART1_RX(val)
-#define bfin_read_IRQ_UART_TX()		bfin_read_IRQ_UART1_TX()
-#define bfin_write_IRQ_UART_TX(val)	bfin_write_IRQ_UART1_TX(val)
-#define bfin_read_IRQ_UART_ERROR()	bfin_read_IRQ_UART1_ERROR()
-#define bfin_write_IRQ_UART_ERROR(val)	bfin_write_IRQ_UART1_ERROR(val)
-#define IRQ_UART_RX			IRQ_UART1_RX
-#define	IRQ_UART_TX			IRQ_UART1_TX
-#define	IRQ_UART_ERROR			IRQ_UART1_ERROR
-
-/* MMR Registers*/
-#define bfin_read_UART_THR()		bfin_read_UART1_THR()
-#define bfin_write_UART_THR(val)	bfin_write_UART1_THR(val)
-#define bfin_read_UART_RBR()		bfin_read_UART1_RBR()
-#define bfin_write_UART_RBR(val)	bfin_write_UART1_RBR(val)
-#define bfin_read_UART_DLL()		bfin_read_UART1_DLL()
-#define bfin_write_UART_DLL(val)	bfin_write_UART1_DLL(val)
-#define bfin_read_UART_IER()		bfin_read_UART1_IER()
-#define bfin_write_UART_IER(val)	bfin_write_UART1_IER(val)
-#define bfin_read_UART_DLH()		bfin_read_UART1_DLH()
-#define bfin_write_UART_DLH(val)	bfin_write_UART1_DLH(val)
-#define bfin_read_UART_IIR()		bfin_read_UART1_IIR()
-#define bfin_write_UART_IIR(val)	bfin_write_UART1_IIR(val)
-#define bfin_read_UART_LCR()		bfin_read_UART1_LCR()
-#define bfin_write_UART_LCR(val)	bfin_write_UART1_LCR(val)
-#define bfin_read_UART_MCR()		bfin_read_UART1_MCR()
-#define bfin_write_UART_MCR(val)	bfin_write_UART1_MCR(val)
-#define bfin_read_UART_LSR()		bfin_read_UART1_LSR()
-#define bfin_write_UART_LSR(val)	bfin_write_UART1_LSR(val)
-#define bfin_read_UART_SCR()		bfin_read_UART1_SCR()
-#define bfin_write_UART_SCR(val)	bfin_write_UART1_SCR(val)
-#define bfin_read_UART_GCTL()		bfin_read_UART1_GCTL()
-#define bfin_write_UART_GCTL(val)	bfin_write_UART1_GCTL(val)
-
-#define BFIN_UART_THR			UART1_THR
-#define BFIN_UART_RBR			UART1_RBR
-#define BFIN_UART_DLL			UART1_DLL
-#define BFIN_UART_IER			UART1_IER
-#define BFIN_UART_DLH			UART1_DLH
-#define BFIN_UART_IIR			UART1_IIR
-#define BFIN_UART_LCR			UART1_LCR
-#define BFIN_UART_MCR			UART1_MCR
-#define BFIN_UART_LSR			UART1_LSR
-#define BFIN_UART_SCR			UART1_SCR
-#define BFIN_UART_GCTL			UART1_GCTL
-
 #define BFIN_UART_NR_PORTS	4
 
 #define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
-- 
1.6.4.2

[PATCH 41/72] Blackfin: cm-bf527/bf537-stamp: fix dm9000 resources

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

The dm9000 driver expects two IORESOURCE_MEM to get at the device, so make
sure we declare things properly.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf527/boards/cm_bf527.c |    7 ++++++-
 arch/blackfin/mach-bf537/boards/stamp.c    |    7 ++++++-
 2 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index cb360e9..18b9bd7 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -311,10 +311,15 @@ static struct platform_device smc91x_device = {
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
-		.end	= 0x203FB800 + 8,
+		.end	= 0x203FB800 + 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= 0x203FB804,
+		.end	= 0x203FB804 + 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_PF9,
 		.end	= IRQ_PF9,
 		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 313249e..9b67006 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -207,10 +207,15 @@ static struct platform_device smc91x_device = {
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
-		.end	= 0x203FB800 + 8,
+		.end	= 0x203FB800 + 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= 0x203FB804,
+		.end	= 0x203FB804 + 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_PF9,
 		.end	= IRQ_PF9,
 		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
-- 
1.6.4.2

[PATCH 42/72] Blackfin: bf548-ezkit: fix incorrect LCD size parameters

[Mike Frysinger]

From: Stefan Pledl <stefan.pledl@mesutronic.de>

I think we have to use the physical dimensions [mm] of the display for
.width and .heigth in struct bfin_bf54xfb_mach_info bf54x_lq043_data which
are copied to fbinfo->var.height/.width in bf54x-lq043fb.c.

linux/fb.h describes this values as 'height/weight of picture in mm'

Otherwise QT calcs the wrong dpi value and the displayed fonts are very
small.

Signed-off-by: Stefan Pledl <stefan.pledl@mesutronic.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf548/boards/ezkit.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index aa82836..3c06010 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -99,8 +99,8 @@ static struct platform_device bfin_isp1760_device = {
 #include <mach/bf54x-lq043.h>
 
 static struct bfin_bf54xfb_mach_info bf54x_lq043_data = {
-	.width =	480,
-	.height =	272,
+	.width =	95,
+	.height =	54,
 	.xres =		{480, 480, 480},
 	.yres =		{272, 272, 272},
 	.bpp =		{24, 24, 24},
-- 
1.6.4.2

[PATCH 43/72] Blackfin: fix read buffer overflow

[Mike Frysinger]

From: Roel Kluin <roel.kluin@gmail.com>

Check whether index is within bounds before testing the element.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/bfin_dma_5xx.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/kernel/bfin_dma_5xx.c b/arch/blackfin/kernel/bfin_dma_5xx.c
index 14dea1a..384868d 100644
--- a/arch/blackfin/kernel/bfin_dma_5xx.c
+++ b/arch/blackfin/kernel/bfin_dma_5xx.c
@@ -147,8 +147,8 @@ EXPORT_SYMBOL(request_dma);
 
 int set_dma_callback(unsigned int channel, irq_handler_t callback, void *data)
 {
-	BUG_ON(!(dma_ch[channel].chan_status != DMA_CHANNEL_FREE
-	       && channel < MAX_DMA_CHANNELS));
+	BUG_ON(channel >= MAX_DMA_CHANNELS ||
+			dma_ch[channel].chan_status == DMA_CHANNEL_FREE);
 
 	if (callback != NULL) {
 		int ret;
@@ -182,8 +182,8 @@ static void clear_dma_buffer(unsigned int channel)
 void free_dma(unsigned int channel)
 {
 	pr_debug("freedma() : BEGIN \n");
-	BUG_ON(!(dma_ch[channel].chan_status != DMA_CHANNEL_FREE
-	       && channel < MAX_DMA_CHANNELS));
+	BUG_ON(channel >= MAX_DMA_CHANNELS ||
+			dma_ch[channel].chan_status == DMA_CHANNEL_FREE);
 
 	/* Halt the DMA */
 	disable_dma(channel);
-- 
1.6.4.2

[PATCH 44/72] Blackfin: bf538-ezkit: add resources for parallel flash

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

The board has some parallel flash hooked up to the async banks, so add
appropriate physmap resources for it.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf538/boards/ezkit.c |   49 +++++++++++++++++++++++++++++++
 1 files changed, 49 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf538/boards/ezkit.c b/arch/blackfin/mach-bf538/boards/ezkit.c
index 42297fa..9113f60 100644
--- a/arch/blackfin/mach-bf538/boards/ezkit.c
+++ b/arch/blackfin/mach-bf538/boards/ezkit.c
@@ -31,6 +31,7 @@
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
 #include <linux/mtd/partitions.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
@@ -561,6 +562,50 @@ static struct platform_device bfin_dpmc = {
 	},
 };
 
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition ezkit_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0x40000,
+		.offset     = 0,
+	}, {
+		.name       = "linux kernel(nor)",
+		.size       = 0x180000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "file system(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data ezkit_flash_data = {
+	.width      = 2,
+	.parts      = ezkit_partitions,
+	.nr_parts   = ARRAY_SIZE(ezkit_partitions),
+};
+
+static struct resource ezkit_flash_resource = {
+	.start = 0x20000000,
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	.end   = 0x202fffff,
+#else
+	.end   = 0x203fffff,
+#endif
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ezkit_flash_device = {
+	.name          = "physmap-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &ezkit_flash_data,
+	},
+	.num_resources = 1,
+	.resource      = &ezkit_flash_resource,
+};
+#endif
+
 static struct platform_device *cm_bf538_devices[] __initdata = {
 
 	&bfin_dpmc,
@@ -609,6 +654,10 @@ static struct platform_device *cm_bf538_devices[] __initdata = {
 #endif
 
 	&bfin_gpios_device,
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&ezkit_flash_device,
+#endif
 };
 
 static int __init ezkit_init(void)
-- 
1.6.4.2

[PATCH 45/72] Blackfin: update anomaly lists

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf518/include/mach/anomaly.h |    1 +
 arch/blackfin/mach-bf527/include/mach/anomaly.h |   13 +++++++++++--
 arch/blackfin/mach-bf537/include/mach/anomaly.h |    2 +-
 arch/blackfin/mach-bf538/include/mach/anomaly.h |    2 +-
 arch/blackfin/mach-bf548/include/mach/anomaly.h |   21 +++++++++++++++++++--
 arch/blackfin/mach-bf561/include/mach/anomaly.h |    2 ++
 6 files changed, 35 insertions(+), 6 deletions(-)

diff --git a/arch/blackfin/mach-bf518/include/mach/anomaly.h b/arch/blackfin/mach-bf518/include/mach/anomaly.h
index 753ed81..e9c6539 100644
--- a/arch/blackfin/mach-bf518/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf518/include/mach/anomaly.h
@@ -124,6 +124,7 @@
 #define ANOMALY_05000386 (0)
 #define ANOMALY_05000389 (0)
 #define ANOMALY_05000400 (0)
+#define ANOMALY_05000402 (0)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000447 (0)
diff --git a/arch/blackfin/mach-bf527/include/mach/anomaly.h b/arch/blackfin/mach-bf527/include/mach/anomaly.h
index c438ca8..3f90526 100644
--- a/arch/blackfin/mach-bf527/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf527/include/mach/anomaly.h
@@ -7,7 +7,7 @@
  */
 
 /* This file should be up to date with:
- *  - Revision C, 03/13/2009; ADSP-BF526 Blackfin Processor Anomaly List
+ *  - Revision D, 08/14/2009; ADSP-BF526 Blackfin Processor Anomaly List
  *  - Revision F, 03/03/2009; ADSP-BF527 Blackfin Processor Anomaly List
  */
 
@@ -176,7 +176,7 @@
 #define ANOMALY_05000443 (1)
 /* The WURESET Bit in the SYSCR Register is not Functional */
 #define ANOMALY_05000445 (1)
-/* USB DMA Short Packet Data Corruption */
+/* USB DMA Mode 1 Short Packet Data Corruption */
 #define ANOMALY_05000450 (1)
 /* BCODE_QUICKBOOT, BCODE_ALLBOOT, and BCODE_FULLBOOT Settings in SYSCR Register Not Functional */
 #define ANOMALY_05000451 (1)
@@ -186,12 +186,20 @@
 #define ANOMALY_05000456 (1)
 /* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */
 #define ANOMALY_05000457 (1)
+/* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */
+#define ANOMALY_05000460 (1)
 /* False Hardware Error when RETI Points to Invalid Memory */
 #define ANOMALY_05000461 (1)
+/* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
+#define ANOMALY_05000462 (1)
 /* USB Rx DMA hang */
 #define ANOMALY_05000465 (1)
+/* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */
+#define ANOMALY_05000466 (1)
 /* Possible RX data corruption when control & data EP FIFOs are accessed via the core */
 #define ANOMALY_05000467 (1)
+/* PLL Latches Incorrect Settings During Reset */
+#define ANOMALY_05000469 (1)
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000099 (0)
@@ -238,6 +246,7 @@
 #define ANOMALY_05000362 (1)
 #define ANOMALY_05000363 (0)
 #define ANOMALY_05000400 (0)
+#define ANOMALY_05000402 (0)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000447 (0)
 #define ANOMALY_05000448 (0)
diff --git a/arch/blackfin/mach-bf537/include/mach/anomaly.h b/arch/blackfin/mach-bf537/include/mach/anomaly.h
index e66aa13..f091ad2 100644
--- a/arch/blackfin/mach-bf537/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf537/include/mach/anomaly.h
@@ -143,7 +143,7 @@
 /* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */
 #define ANOMALY_05000371 (1)
 /* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
-#define ANOMALY_05000402 (__SILICON_REVISION__ >= 5)
+#define ANOMALY_05000402 (__SILICON_REVISION__ == 2)
 /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */
 #define ANOMALY_05000403 (1)
 /* Speculative Fetches Can Cause Undesired External FIFO Operations */
diff --git a/arch/blackfin/mach-bf538/include/mach/anomaly.h b/arch/blackfin/mach-bf538/include/mach/anomaly.h
index 451cf8a..26b7608 100644
--- a/arch/blackfin/mach-bf538/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf538/include/mach/anomaly.h
@@ -113,7 +113,7 @@
 /* GPIO Pins PC1 and PC4 Can Function as Normal Outputs */
 #define ANOMALY_05000375 (__SILICON_REVISION__ < 4)
 /* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
-#define ANOMALY_05000402 (__SILICON_REVISION__ < 4)
+#define ANOMALY_05000402 (__SILICON_REVISION__ == 3)
 /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */
 #define ANOMALY_05000403 (1)
 /* Speculative Fetches Can Cause Undesired External FIFO Operations */
diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h
index cd040fe..52b116a 100644
--- a/arch/blackfin/mach-bf548/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h
@@ -7,7 +7,7 @@
  */
 
 /* This file should be up to date with:
- *  - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
+ *  - Revision I, 07/23/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
@@ -162,6 +162,8 @@
 #define ANOMALY_05000430 (__SILICON_REVISION__ >= 2)
 /* Incorrect Use of Stack in Lockbox Firmware During Authentication */
 #define ANOMALY_05000431 (__SILICON_REVISION__ < 3)
+/* SW Breakpoints Ignored Upon Return From Lockbox Authentication */
+#define ANOMALY_05000434 (1)
 /* OTP Write Accesses Not Supported */
 #define ANOMALY_05000442 (__SILICON_REVISION__ < 1)
 /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */
@@ -176,12 +178,26 @@
 #define ANOMALY_05000449 (__SILICON_REVISION__ == 1)
 /* USB DMA Mode 1 Short Packet Data Corruption */
 #define ANOMALY_05000450 (1)
+/* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */
+#define ANOMALY_05000452 (__SILICON_REVISION__ < 1)
 /* USB Receive Interrupt Is Not Generated in DMA Mode 1 */
-#define ANOMALY_05000456 (__SILICON_REVISION__ < 3)
+#define ANOMALY_05000456 (1)
+/* Host DMA Port Responds to Certain Bus Activity Without HOST_CE Assertion */
+#define ANOMALY_05000457 (1)
+/* USB DMA Mode 1 Failure When Multiple USB DMA Channels Are Concurrently Enabled */
+#define ANOMALY_05000460 (1)
 /* False Hardware Error when RETI Points to Invalid Memory */
 #define ANOMALY_05000461 (1)
+/* Synchronization Problem at Startup May Cause SPORT Transmit Channels to Misalign */
+#define ANOMALY_05000462 (1)
+/* USB DMA RX Data Corruption */
+#define ANOMALY_05000463 (1)
+/* USB TX DMA Hang */
+#define ANOMALY_05000464 (1)
 /* USB Rx DMA hang */
 #define ANOMALY_05000465 (1)
+/* TxPktRdy Bit Not Set for Transmit Endpoint When Core and DMA Access USB Endpoint FIFOs Simultaneously */
+#define ANOMALY_05000466 (1)
 /* Possible RX data corruption when control & data EP FIFOs are accessed via the core */
 #define ANOMALY_05000467 (1)
 
@@ -230,6 +246,7 @@
 #define ANOMALY_05000364 (0)
 #define ANOMALY_05000380 (0)
 #define ANOMALY_05000400 (0)
+#define ANOMALY_05000402 (0)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000435 (0)
diff --git a/arch/blackfin/mach-bf561/include/mach/anomaly.h b/arch/blackfin/mach-bf561/include/mach/anomaly.h
index a5312b2..70da495 100644
--- a/arch/blackfin/mach-bf561/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf561/include/mach/anomaly.h
@@ -262,6 +262,8 @@
 #define ANOMALY_05000366 (1)
 /* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */
 #define ANOMALY_05000371 (1)
+/* SSYNC Stalls Processor when Executed from Non-Cacheable Memory */
+#define ANOMALY_05000402 (__SILICON_REVISION__ == 4)
 /* Level-Sensitive External GPIO Wakeups May Cause Indefinite Stall */
 #define ANOMALY_05000403 (1)
 /* TESTSET Instruction Causes Data Corruption with Writeback Data Cache Enabled */
-- 
1.6.4.2

[PATCH 46/72] Blackfin: bf537-stamp: update ad1836 resources

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

Update the ad1836 resources for the new ASoC driver.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |   22 +++++++++++++++++-----
 1 files changed, 17 insertions(+), 5 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 9b67006..d438ca4 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -532,8 +532,8 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
-	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 	.enable_dma = 0,
 	.bits_per_word = 16,
@@ -883,14 +883,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
-	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+#if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
+	|| defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 	{
 		.modalias = "ad1836-spi",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
 		.controller_data = &ad1836_spi_chip_info,
+		.mode = SPI_MODE_3,
 	},
 #endif
 
@@ -1628,6 +1629,13 @@ static struct platform_device bfin_dpmc = {
 	},
 };
 
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+static struct platform_device bfin_tdm = {
+	.name = "bfin-tdm",
+	/* TODO: add platform data here */
+};
+#endif
+
 static struct platform_device *stamp_devices[] __initdata = {
 
 	&bfin_dpmc,
@@ -1733,6 +1741,10 @@ static struct platform_device *stamp_devices[] __initdata = {
 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 	&stamp_flash_device,
 #endif
+
+#if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
+	&bfin_tdm,
+#endif
 };
 
 static int __init stamp_init(void)
-- 
1.6.4.2

[PATCH 47/72] Blackfin: cleanup sync handling when enabling/disabling cplbs

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

The handling of updating the [DI]MEM_CONTROL MMRs does not follow proper
sync procedures as laid out in the Blackfin programming manual.  So rather
than audit/fix every call location, create helper functions that do the
right things in order to safely update these MMRs.  Then convert all call
sites to use these new helper functions.

While we're fixing the code, drop the workaround for anomaly 05000125 as
that anomaly applies to old versions of silicon that we do not support.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/cplb.h            |   46 +++++++++++++++++++-
 arch/blackfin/kernel/cplb-mpu/cacheinit.c   |    6 ++-
 arch/blackfin/kernel/cplb-mpu/cplbmgr.c     |   61 +++++---------------------
 arch/blackfin/kernel/cplb-nompu/cacheinit.c |    6 ++-
 arch/blackfin/kernel/cplb-nompu/cplbmgr.c   |   33 ++------------
 arch/blackfin/mach-bf561/secondary.S        |   20 ++-------
 arch/blackfin/mach-common/entry.S           |   14 ++----
 arch/blackfin/mach-common/pm.c              |   64 +++-----------------------
 8 files changed, 84 insertions(+), 166 deletions(-)

diff --git a/arch/blackfin/include/asm/cplb.h b/arch/blackfin/include/asm/cplb.h
index c5dacf8..d18d168 100644
--- a/arch/blackfin/include/asm/cplb.h
+++ b/arch/blackfin/include/asm/cplb.h
@@ -125,4 +125,48 @@
 #define FAULT_USERSUPV  (1 << 17)
 #define FAULT_CPLBBITS  0x0000ffff
 
-#endif				/* _CPLB_H */
+#ifndef __ASSEMBLY__
+
+static inline void _disable_cplb(u32 mmr, u32 mask)
+{
+	u32 ctrl = bfin_read32(mmr) & ~mask;
+	/* CSYNC to ensure load store ordering */
+	__builtin_bfin_csync();
+	bfin_write32(mmr, ctrl);
+	__builtin_bfin_ssync();
+}
+static inline void disable_cplb(u32 mmr, u32 mask)
+{
+	u32 ctrl = bfin_read32(mmr) & ~mask;
+	CSYNC();
+	bfin_write32(mmr, ctrl);
+	SSYNC();
+}
+#define _disable_dcplb() _disable_cplb(DMEM_CONTROL, ENDCPLB)
+#define  disable_dcplb()  disable_cplb(DMEM_CONTROL, ENDCPLB)
+#define _disable_icplb() _disable_cplb(IMEM_CONTROL, ENICPLB)
+#define  disable_icplb()  disable_cplb(IMEM_CONTROL, ENICPLB)
+
+static inline void _enable_cplb(u32 mmr, u32 mask)
+{
+	u32 ctrl = bfin_read32(mmr) | mask;
+	/* CSYNC to ensure load store ordering */
+	__builtin_bfin_csync();
+	bfin_write32(mmr, ctrl);
+	__builtin_bfin_ssync();
+}
+static inline void enable_cplb(u32 mmr, u32 mask)
+{
+	u32 ctrl = bfin_read32(mmr) | mask;
+	CSYNC();
+	bfin_write32(mmr, ctrl);
+	SSYNC();
+}
+#define _enable_dcplb()  _enable_cplb(DMEM_CONTROL, ENDCPLB)
+#define  enable_dcplb()   enable_cplb(DMEM_CONTROL, ENDCPLB)
+#define _enable_icplb()  _enable_cplb(IMEM_CONTROL, ENICPLB)
+#define  enable_icplb()   enable_cplb(IMEM_CONTROL, ENICPLB)
+
+#endif		/* __ASSEMBLY__ */
+
+#endif		/* _CPLB_H */
diff --git a/arch/blackfin/kernel/cplb-mpu/cacheinit.c b/arch/blackfin/kernel/cplb-mpu/cacheinit.c
index d5a86c3..a082681 100644
--- a/arch/blackfin/kernel/cplb-mpu/cacheinit.c
+++ b/arch/blackfin/kernel/cplb-mpu/cacheinit.c
@@ -30,13 +30,14 @@ void __cpuinit bfin_icache_init(struct cplb_entry *icplb_tbl)
 	unsigned long ctrl;
 	int i;
 
-	SSYNC();
 	for (i = 0; i < MAX_CPLBS; i++) {
 		bfin_write32(ICPLB_ADDR0 + i * 4, icplb_tbl[i].addr);
 		bfin_write32(ICPLB_DATA0 + i * 4, icplb_tbl[i].data);
 	}
 	ctrl = bfin_read_IMEM_CONTROL();
 	ctrl |= IMC | ENICPLB;
+	/* CSYNC to ensure load store ordering */
+	CSYNC();
 	bfin_write_IMEM_CONTROL(ctrl);
 	SSYNC();
 }
@@ -48,7 +49,6 @@ void __cpuinit bfin_dcache_init(struct cplb_entry *dcplb_tbl)
 	unsigned long ctrl;
 	int i;
 
-	SSYNC();
 	for (i = 0; i < MAX_CPLBS; i++) {
 		bfin_write32(DCPLB_ADDR0 + i * 4, dcplb_tbl[i].addr);
 		bfin_write32(DCPLB_DATA0 + i * 4, dcplb_tbl[i].data);
@@ -63,6 +63,8 @@ void __cpuinit bfin_dcache_init(struct cplb_entry *dcplb_tbl)
 	 *  to port B
 	 */
 	ctrl |= DMEM_CNTR | PORT_PREF0 | (ANOMALY_05000287 ? PORT_PREF1 : 0);
+	/* CSYNC to ensure load store ordering */
+	CSYNC();
 	bfin_write_DMEM_CONTROL(ctrl);
 	SSYNC();
 }
diff --git a/arch/blackfin/kernel/cplb-mpu/cplbmgr.c b/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
index bcdfe9b..651b127 100644
--- a/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
+++ b/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
@@ -22,6 +22,7 @@
 
 #include <asm/blackfin.h>
 #include <asm/cacheflush.h>
+#include <asm/cplb.h>
 #include <asm/cplbinit.h>
 #include <asm/mmu_context.h>
 
@@ -41,46 +42,6 @@ int nr_dcplb_miss[NR_CPUS], nr_icplb_miss[NR_CPUS];
 int nr_icplb_supv_miss[NR_CPUS], nr_dcplb_prot[NR_CPUS];
 int nr_cplb_flush[NR_CPUS];
 
-static inline void disable_dcplb(void)
-{
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_DMEM_CONTROL();
-	ctrl &= ~ENDCPLB;
-	bfin_write_DMEM_CONTROL(ctrl);
-	SSYNC();
-}
-
-static inline void enable_dcplb(void)
-{
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_DMEM_CONTROL();
-	ctrl |= ENDCPLB;
-	bfin_write_DMEM_CONTROL(ctrl);
-	SSYNC();
-}
-
-static inline void disable_icplb(void)
-{
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_IMEM_CONTROL();
-	ctrl &= ~ENICPLB;
-	bfin_write_IMEM_CONTROL(ctrl);
-	SSYNC();
-}
-
-static inline void enable_icplb(void)
-{
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_IMEM_CONTROL();
-	ctrl |= ENICPLB;
-	bfin_write_IMEM_CONTROL(ctrl);
-	SSYNC();
-}
-
 /*
  * Given the contents of the status register, return the index of the
  * CPLB that caused the fault.
@@ -198,10 +159,10 @@ static noinline int dcplb_miss(unsigned int cpu)
 	dcplb_tbl[cpu][idx].addr = addr;
 	dcplb_tbl[cpu][idx].data = d_data;
 
-	disable_dcplb();
+	_disable_dcplb();
 	bfin_write32(DCPLB_DATA0 + idx * 4, d_data);
 	bfin_write32(DCPLB_ADDR0 + idx * 4, addr);
-	enable_dcplb();
+	_enable_dcplb();
 
 	return 0;
 }
@@ -288,10 +249,10 @@ static noinline int icplb_miss(unsigned int cpu)
 	icplb_tbl[cpu][idx].addr = addr;
 	icplb_tbl[cpu][idx].data = i_data;
 
-	disable_icplb();
+	_disable_icplb();
 	bfin_write32(ICPLB_DATA0 + idx * 4, i_data);
 	bfin_write32(ICPLB_ADDR0 + idx * 4, addr);
-	enable_icplb();
+	_enable_icplb();
 
 	return 0;
 }
@@ -340,19 +301,19 @@ void flush_switched_cplbs(unsigned int cpu)
 	nr_cplb_flush[cpu]++;
 
 	local_irq_save_hw(flags);
-	disable_icplb();
+	_disable_icplb();
 	for (i = first_switched_icplb; i < MAX_CPLBS; i++) {
 		icplb_tbl[cpu][i].data = 0;
 		bfin_write32(ICPLB_DATA0 + i * 4, 0);
 	}
-	enable_icplb();
+	_enable_icplb();
 
-	disable_dcplb();
+	_disable_dcplb();
 	for (i = first_switched_dcplb; i < MAX_CPLBS; i++) {
 		dcplb_tbl[cpu][i].data = 0;
 		bfin_write32(DCPLB_DATA0 + i * 4, 0);
 	}
-	enable_dcplb();
+	_enable_dcplb();
 	local_irq_restore_hw(flags);
 
 }
@@ -385,7 +346,7 @@ void set_mask_dcplbs(unsigned long *masks, unsigned int cpu)
 #endif
 	}
 
-	disable_dcplb();
+	_disable_dcplb();
 	for (i = first_mask_dcplb; i < first_switched_dcplb; i++) {
 		dcplb_tbl[cpu][i].addr = addr;
 		dcplb_tbl[cpu][i].data = d_data;
@@ -393,6 +354,6 @@ void set_mask_dcplbs(unsigned long *masks, unsigned int cpu)
 		bfin_write32(DCPLB_ADDR0 + i * 4, addr);
 		addr += PAGE_SIZE;
 	}
-	enable_dcplb();
+	_enable_dcplb();
 	local_irq_restore_hw(flags);
 }
diff --git a/arch/blackfin/kernel/cplb-nompu/cacheinit.c b/arch/blackfin/kernel/cplb-nompu/cacheinit.c
index d5a86c3..a082681 100644
--- a/arch/blackfin/kernel/cplb-nompu/cacheinit.c
+++ b/arch/blackfin/kernel/cplb-nompu/cacheinit.c
@@ -30,13 +30,14 @@ void __cpuinit bfin_icache_init(struct cplb_entry *icplb_tbl)
 	unsigned long ctrl;
 	int i;
 
-	SSYNC();
 	for (i = 0; i < MAX_CPLBS; i++) {
 		bfin_write32(ICPLB_ADDR0 + i * 4, icplb_tbl[i].addr);
 		bfin_write32(ICPLB_DATA0 + i * 4, icplb_tbl[i].data);
 	}
 	ctrl = bfin_read_IMEM_CONTROL();
 	ctrl |= IMC | ENICPLB;
+	/* CSYNC to ensure load store ordering */
+	CSYNC();
 	bfin_write_IMEM_CONTROL(ctrl);
 	SSYNC();
 }
@@ -48,7 +49,6 @@ void __cpuinit bfin_dcache_init(struct cplb_entry *dcplb_tbl)
 	unsigned long ctrl;
 	int i;
 
-	SSYNC();
 	for (i = 0; i < MAX_CPLBS; i++) {
 		bfin_write32(DCPLB_ADDR0 + i * 4, dcplb_tbl[i].addr);
 		bfin_write32(DCPLB_DATA0 + i * 4, dcplb_tbl[i].data);
@@ -63,6 +63,8 @@ void __cpuinit bfin_dcache_init(struct cplb_entry *dcplb_tbl)
 	 *  to port B
 	 */
 	ctrl |= DMEM_CNTR | PORT_PREF0 | (ANOMALY_05000287 ? PORT_PREF1 : 0);
+	/* CSYNC to ensure load store ordering */
+	CSYNC();
 	bfin_write_DMEM_CONTROL(ctrl);
 	SSYNC();
 }
diff --git a/arch/blackfin/kernel/cplb-nompu/cplbmgr.c b/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
index 12b0308..aabbb42 100644
--- a/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
+++ b/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
@@ -48,36 +48,13 @@ int nr_cplb_flush[NR_CPUS], nr_dcplb_prot[NR_CPUS];
 #define MGR_ATTR
 #endif
 
-/*
- * We're in an exception handler.  The normal cli nop nop workaround
- * isn't going to do very much, as the only thing that can interrupt
- * us is an NMI, and the cli isn't going to stop that.
- */
-#define NOWA_SSYNC __asm__ __volatile__ ("ssync;")
-
-/* Anomaly handlers provide SSYNCs, so avoid extra if anomaly is present */
-#if ANOMALY_05000125
-
-#define bfin_write_DMEM_CONTROL_SSYNC(v)    bfin_write_DMEM_CONTROL(v)
-#define bfin_write_IMEM_CONTROL_SSYNC(v)    bfin_write_IMEM_CONTROL(v)
-
-#else
-
-#define bfin_write_DMEM_CONTROL_SSYNC(v) \
-    do { NOWA_SSYNC; bfin_write_DMEM_CONTROL(v); NOWA_SSYNC; } while (0)
-#define bfin_write_IMEM_CONTROL_SSYNC(v) \
-    do { NOWA_SSYNC; bfin_write_IMEM_CONTROL(v); NOWA_SSYNC; } while (0)
-
-#endif
-
 static inline void write_dcplb_data(int cpu, int idx, unsigned long data,
 				    unsigned long addr)
 {
-	unsigned long ctrl = bfin_read_DMEM_CONTROL();
-	bfin_write_DMEM_CONTROL_SSYNC(ctrl & ~ENDCPLB);
+	_disable_dcplb();
 	bfin_write32(DCPLB_DATA0 + idx * 4, data);
 	bfin_write32(DCPLB_ADDR0 + idx * 4, addr);
-	bfin_write_DMEM_CONTROL_SSYNC(ctrl);
+	_enable_dcplb();
 
 #ifdef CONFIG_CPLB_INFO
 	dcplb_tbl[cpu][idx].addr = addr;
@@ -88,12 +65,10 @@ static inline void write_dcplb_data(int cpu, int idx, unsigned long data,
 static inline void write_icplb_data(int cpu, int idx, unsigned long data,
 				    unsigned long addr)
 {
-	unsigned long ctrl = bfin_read_IMEM_CONTROL();
-
-	bfin_write_IMEM_CONTROL_SSYNC(ctrl & ~ENICPLB);
+	_disable_icplb();
 	bfin_write32(ICPLB_DATA0 + idx * 4, data);
 	bfin_write32(ICPLB_ADDR0 + idx * 4, addr);
-	bfin_write_IMEM_CONTROL_SSYNC(ctrl);
+	_enable_icplb();
 
 #ifdef CONFIG_CPLB_INFO
 	icplb_tbl[cpu][idx].addr = addr;
diff --git a/arch/blackfin/mach-bf561/secondary.S b/arch/blackfin/mach-bf561/secondary.S
index 097550f..f72a6af 100644
--- a/arch/blackfin/mach-bf561/secondary.S
+++ b/arch/blackfin/mach-bf561/secondary.S
@@ -85,16 +85,10 @@ ENTRY(_coreb_trampoline_start)
 	R0 = ~ENICPLB;
 	R0 = R0 & R1;
 
-	/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
-	CLI R2;
-	SSYNC;
-#endif
+	/* Disabling of CPLBs should be proceeded by a CSYNC */
+	CSYNC;
 	[p0] = R0;
 	SSYNC;
-#ifdef ANOMALY_05000125
-	STI R2;
-#endif
 
 	/* Turn off the dcache */
 	p0.l = LO(DMEM_CONTROL);
@@ -103,16 +97,10 @@ ENTRY(_coreb_trampoline_start)
 	R0 = ~ENDCPLB;
 	R0 = R0 & R1;
 
-	/* Anomaly 05000125 */
-#ifdef ANOMALY_05000125
-	CLI R2;
-	SSYNC;
-#endif
+	/* Disabling of CPLBs should be proceeded by a CSYNC */
+	CSYNC;
 	[p0] = R0;
 	SSYNC;
-#ifdef ANOMALY_05000125
-	STI R2;
-#endif
 
 	/* in case of double faults, save a few things */
 	p0.l = _init_retx_coreb;
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 4e8e3fe..e7eb163 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -397,8 +397,7 @@ ENTRY(_double_fault)
 
 	R5 = [P4];              /* Control Register*/
 	BITCLR(R5,ENICPLB_P);
-	SSYNC;          /* SSYNC required before writing to IMEM_CONTROL. */
-	.align 8;
+	CSYNC;          /* Disabling of CPLBs should be proceeded by a CSYNC */
 	[P4] = R5;
 	SSYNC;
 
@@ -406,8 +405,7 @@ ENTRY(_double_fault)
 	P4.H = HI(DMEM_CONTROL);
 	R5 = [P4];
 	BITCLR(R5,ENDCPLB_P);
-	SSYNC;          /* SSYNC required before writing to DMEM_CONTROL. */
-	.align 8;
+	CSYNC;          /* Disabling of CPLBs should be proceeded by a CSYNC */
 	[P4] = R5;
 	SSYNC;
 
@@ -1146,9 +1144,7 @@ ENTRY(_early_trap)
 
 	R5 = [P4];              /* Control Register*/
 	BITCLR(R5,ENICPLB_P);
-	CLI R1;
-	SSYNC;          /* SSYNC required before writing to IMEM_CONTROL. */
-	.align 8;
+	CSYNC;          /* Disabling of CPLBs should be proceeded by a CSYNC */
 	[P4] = R5;
 	SSYNC;
 
@@ -1156,11 +1152,9 @@ ENTRY(_early_trap)
 	P4.H = HI(DMEM_CONTROL);
 	R5 = [P4];
 	BITCLR(R5,ENDCPLB_P);
-	SSYNC;          /* SSYNC required before writing to DMEM_CONTROL. */
-	.align 8;
+	CSYNC;          /* Disabling of CPLBs should be proceeded by a CSYNC */
 	[P4] = R5;
 	SSYNC;
-	STI R1;
 
 	r0 = sp;        /* stack frame pt_regs pointer argument ==> r0 */
 	r1 = RETX;
diff --git a/arch/blackfin/mach-common/pm.c b/arch/blackfin/mach-common/pm.c
index 9e7e27b..0e3d4ff 100644
--- a/arch/blackfin/mach-common/pm.c
+++ b/arch/blackfin/mach-common/pm.c
@@ -38,6 +38,7 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 
+#include <asm/cplb.h>
 #include <asm/gpio.h>
 #include <asm/dma.h>
 #include <asm/dpmc.h>
@@ -170,58 +171,6 @@ static void flushinv_all_dcache(void)
 }
 #endif
 
-static inline void dcache_disable(void)
-{
-#ifdef CONFIG_BFIN_DCACHE
-	unsigned long ctrl;
-
-#if defined(CONFIG_BFIN_EXTMEM_WRITEBACK) || defined(CONFIG_BFIN_L2_WRITEBACK)
-	flushinv_all_dcache();
-#endif
-	SSYNC();
-	ctrl = bfin_read_DMEM_CONTROL();
-	ctrl &= ~ENDCPLB;
-	bfin_write_DMEM_CONTROL(ctrl);
-	SSYNC();
-#endif
-}
-
-static inline void dcache_enable(void)
-{
-#ifdef CONFIG_BFIN_DCACHE
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_DMEM_CONTROL();
-	ctrl |= ENDCPLB;
-	bfin_write_DMEM_CONTROL(ctrl);
-	SSYNC();
-#endif
-}
-
-static inline void icache_disable(void)
-{
-#ifdef CONFIG_BFIN_ICACHE
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_IMEM_CONTROL();
-	ctrl &= ~ENICPLB;
-	bfin_write_IMEM_CONTROL(ctrl);
-	SSYNC();
-#endif
-}
-
-static inline void icache_enable(void)
-{
-#ifdef CONFIG_BFIN_ICACHE
-	unsigned long ctrl;
-	SSYNC();
-	ctrl = bfin_read_IMEM_CONTROL();
-	ctrl |= ENICPLB;
-	bfin_write_IMEM_CONTROL(ctrl);
-	SSYNC();
-#endif
-}
-
 int bfin_pm_suspend_mem_enter(void)
 {
 	unsigned long flags;
@@ -258,16 +207,19 @@ int bfin_pm_suspend_mem_enter(void)
 
 	bfin_gpio_pm_hibernate_suspend();
 
-	dcache_disable();
-	icache_disable();
+#if defined(CONFIG_BFIN_EXTMEM_WRITEBACK) || defined(CONFIG_BFIN_L2_WRITEBACK)
+	flushinv_all_dcache();
+#endif
+	_disable_dcplb();
+	_disable_icplb();
 	bf53x_suspend_l1_mem(memptr);
 
 	do_hibernate(wakeup | vr_wakeup);	/* Goodbye */
 
 	bf53x_resume_l1_mem(memptr);
 
-	icache_enable();
-	dcache_enable();
+	_enable_icplb();
+	_enable_dcplb();
 
 	bfin_gpio_pm_hibernate_restore();
 	blackfin_dma_resume();
-- 
1.6.4.2

[PATCH 48/72] Blackfin: SMP port does not yet support cpu frequency scaling

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

We have an item to get this fixed, but in the mean time, disable selection
via Kconfig dependencies.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig |    4 +++-
 1 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 8d04ed9..6040aad 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -1152,11 +1152,12 @@ source "fs/Kconfig.binfmt"
 endmenu
 
 menu "Power management options"
+	depends on !SMP
+
 source "kernel/power/Kconfig"
 
 config ARCH_SUSPEND_POSSIBLE
 	def_bool y
-	depends on !SMP
 
 choice
 	prompt "Standby Power Saving Mode"
@@ -1244,6 +1245,7 @@ config PM_BFIN_WAKE_GP
 endmenu
 
 menu "CPU Frequency scaling"
+	depends on !SMP
 
 source "drivers/cpufreq/Kconfig"
 
-- 
1.6.4.2

[PATCH 49/72] Blackfin: fix BF522/BF523 max VCO mixup

[Mike Frysinger]

The BF522 and BF523 had their real max VCO values swapped.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 6040aad..8d6b5ae 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -574,8 +574,8 @@ config MAX_VCO_HZ
 	default 400000000 if BF514
 	default 400000000 if BF516
 	default 400000000 if BF518
-	default 600000000 if BF522
-	default 400000000 if BF523
+	default 400000000 if BF522
+	default 600000000 if BF523
 	default 400000000 if BF524
 	default 600000000 if BF525
 	default 400000000 if BF526
-- 
1.6.4.2

[PATCH 50/72] Blackfin: do not trace the exception handler

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

Since the exception handler cannot cause exceptions, we cannot trace it
without easily causing double faults and crashing the system.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/traps.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 0904430..7b3ba06 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -257,7 +257,7 @@ static int kernel_mode_regs(struct pt_regs *regs)
 	return regs->ipend & 0xffc0;
 }
 
-asmlinkage void trap_c(struct pt_regs *fp)
+asmlinkage notrace void trap_c(struct pt_regs *fp)
 {
 #ifdef CONFIG_DEBUG_BFIN_HWTRACE_ON
 	int j;
-- 
1.6.4.2

[PATCH 51/72] Blackfin: drop board resources for dead devices (pbx/ad9960)

[Mike Frysinger]

These hardware devices are dead and the drivers never cleaned up/merged,
so punt the useless board resource info.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf518/boards/ezbrd.c     |   27 ----------------
 arch/blackfin/mach-bf527/boards/cm_bf527.c  |   43 --------------------------
 arch/blackfin/mach-bf527/boards/ezbrd.c     |   27 ----------------
 arch/blackfin/mach-bf527/boards/ezkit.c     |   43 --------------------------
 arch/blackfin/mach-bf533/boards/H8606.c     |   26 ----------------
 arch/blackfin/mach-bf533/boards/stamp.c     |   28 -----------------
 arch/blackfin/mach-bf537/boards/cm_bf537.c  |   17 ----------
 arch/blackfin/mach-bf537/boards/pnav10.c    |   16 ----------
 arch/blackfin/mach-bf537/boards/stamp.c     |   44 ---------------------------
 arch/blackfin/mach-bf537/boards/tcm_bf537.c |   17 ----------
 arch/blackfin/mach-bf561/boards/cm_bf561.c  |   16 ----------
 11 files changed, 0 insertions(+), 304 deletions(-)

diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 4c594e6..03e4a99 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -199,15 +199,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -296,24 +287,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 18b9bd7..fdd518c 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -495,13 +495,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -509,15 +502,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -591,15 +575,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -610,24 +585,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 809c790..68b4c80 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -263,15 +263,6 @@ static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -376,24 +367,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 617a287..4ab9cfa 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -512,13 +512,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -526,15 +519,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 	.enable_dma = 0,
@@ -632,15 +616,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
@@ -652,24 +627,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 1bd8b61..30ff3c4 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -201,15 +201,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x1c04,
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 /* Notice: for blackfin, the speed_hz is the value of register
  * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
@@ -248,23 +239,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias	 = "fxs-spi",
-		.max_speed_hz	 = 4,
-		.bus_num	 = 1,
-		.chip_select	 = 3,
-		.controller_data = &spi_si3xxx_chip_info,
-	},
-
-	{
-		.modalias	 = "fxo-spi",
-		.max_speed_hz	 = 4,
-		.bus_num	 = 1,
-		.chip_select	 = 2,
-		.controller_data = &spi_si3xxx_chip_info,
-	},
-#endif
 };
 
 /* SPI (0) */
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index f3dc283..3954baa 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -219,15 +219,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 static struct bfin5xx_spi_chip spidev_chip_info = {
 	.enable_dma = 0,
@@ -298,25 +289,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
-
 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 	{
 		.modalias = "spidev",
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 3681d2c..159e5b2 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 3bbe102..0d93bbe 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -293,13 +293,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -366,15 +359,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d438ca4..d5aabee 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -549,13 +549,6 @@ static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
 #include <linux/input.h>
 #include <linux/input/ad714x.h>
@@ -698,15 +691,6 @@ static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-	.ctl_reg	= 0x4, /* send zero */
-	.enable_dma	= 0,
-	.bits_per_word	= 8,
-	.cs_change_per_word = 1,
-};
-#endif
-
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 #include <linux/spi/ad7877.h>
 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
@@ -906,16 +890,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_INPUT_EVAL_AD7147EBZ)
 	{
 		.modalias = "ad714x_captouch",
@@ -940,24 +914,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.mode = SPI_MODE_3,
 	},
 #endif
-#if defined(CONFIG_PBX)
-	{
-		.modalias = "fxs-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J11_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-	{
-		.modalias = "fxo-spi",
-		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 8 - CONFIG_J19_JUMPER,
-		.controller_data = &spi_si3xxx_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 	{
 		.modalias		= "ad7877",
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 97a86b4..88eade8 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -101,13 +101,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -150,16 +143,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 	},
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index ebb0755..cedcc3c 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -98,13 +98,6 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
 
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 	.enable_dma = 0,
@@ -146,15 +139,6 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.controller_data = &ad1836_spi_chip_info,
 	},
 #endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-	{
-		.modalias = "ad9960-spi",
-		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &ad9960_spi_chip_info,
-	},
-#endif
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
-- 
1.6.4.2

[PATCH 52/72] Blackfin: punt dead cache locking code

[Mike Frysinger]

No one uses these functions, and some are duplicate of existing C code.  So
just punt the whole thing.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig                   |    4 -
 arch/blackfin/include/asm/bfin-global.h |    5 -
 arch/blackfin/kernel/setup.c            |   51 -------
 arch/blackfin/mach-common/Makefile      |    1 -
 arch/blackfin/mach-common/lock.S        |  223 -------------------------------
 5 files changed, 0 insertions(+), 284 deletions(-)
 delete mode 100644 arch/blackfin/mach-common/lock.S

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 8d6b5ae..f20dc77 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -917,10 +917,6 @@ comment "Cache Support"
 config BFIN_ICACHE
 	bool "Enable ICACHE"
 	default y
-config BFIN_ICACHE_LOCK
-	bool "Enable Instruction Cache Locking"
-	depends on BFIN_ICACHE
-	default n
 config BFIN_EXTMEM_ICACHEABLE
 	bool "Enable ICACHE for external memory"
 	depends on BFIN_ICACHE
diff --git a/arch/blackfin/include/asm/bfin-global.h b/arch/blackfin/include/asm/bfin-global.h
index e6ecbe4..aef0594 100644
--- a/arch/blackfin/include/asm/bfin-global.h
+++ b/arch/blackfin/include/asm/bfin-global.h
@@ -99,11 +99,6 @@ extern unsigned long bfin_sic_iwr[];
 extern unsigned vr_wakeup;
 extern u16 _bfin_swrst; /* shadow for Software Reset Register (SWRST) */
 
-#ifdef CONFIG_BFIN_ICACHE_LOCK
-extern void cache_grab_lock(int way);
-extern void bfin_cache_lock(int way);
-#endif
-
 #endif
 
 #endif				/* _BLACKFIN_H_ */
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index f92fffc..ce02f98 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -1238,57 +1238,6 @@ static int show_cpuinfo(struct seq_file *m, void *v)
 #ifdef __ARCH_SYNC_CORE_ICACHE
 	seq_printf(m, "SMP Icache Flushes\t: %lu\n\n", cpudata->icache_invld_count);
 #endif
-#ifdef CONFIG_BFIN_ICACHE_LOCK
-	switch ((cpudata->imemctl >> 3) & WAYALL_L) {
-	case WAY0_L:
-		seq_printf(m, "Way0 Locked-Down\n");
-		break;
-	case WAY1_L:
-		seq_printf(m, "Way1 Locked-Down\n");
-		break;
-	case WAY01_L:
-		seq_printf(m, "Way0,Way1 Locked-Down\n");
-		break;
-	case WAY2_L:
-		seq_printf(m, "Way2 Locked-Down\n");
-		break;
-	case WAY02_L:
-		seq_printf(m, "Way0,Way2 Locked-Down\n");
-		break;
-	case WAY12_L:
-		seq_printf(m, "Way1,Way2 Locked-Down\n");
-		break;
-	case WAY012_L:
-		seq_printf(m, "Way0,Way1 & Way2 Locked-Down\n");
-		break;
-	case WAY3_L:
-		seq_printf(m, "Way3 Locked-Down\n");
-		break;
-	case WAY03_L:
-		seq_printf(m, "Way0,Way3 Locked-Down\n");
-		break;
-	case WAY13_L:
-		seq_printf(m, "Way1,Way3 Locked-Down\n");
-		break;
-	case WAY013_L:
-		seq_printf(m, "Way 0,Way1,Way3 Locked-Down\n");
-		break;
-	case WAY32_L:
-		seq_printf(m, "Way3,Way2 Locked-Down\n");
-		break;
-	case WAY320_L:
-		seq_printf(m, "Way3,Way2,Way0 Locked-Down\n");
-		break;
-	case WAY321_L:
-		seq_printf(m, "Way3,Way2,Way1 Locked-Down\n");
-		break;
-	case WAYALL_L:
-		seq_printf(m, "All Ways are locked\n");
-		break;
-	default:
-		seq_printf(m, "No Ways are locked\n");
-	}
-#endif
 
 	if (cpu_num != num_possible_cpus() - 1)
 		return 0;
diff --git a/arch/blackfin/mach-common/Makefile b/arch/blackfin/mach-common/Makefile
index dd8b2dc..814cb48 100644
--- a/arch/blackfin/mach-common/Makefile
+++ b/arch/blackfin/mach-common/Makefile
@@ -6,7 +6,6 @@ obj-y := \
 	cache.o cache-c.o entry.o head.o \
 	interrupt.o arch_checks.o ints-priority.o
 
-obj-$(CONFIG_BFIN_ICACHE_LOCK) += lock.o
 obj-$(CONFIG_PM)          += pm.o dpmc_modes.o
 obj-$(CONFIG_CPU_FREQ)    += cpufreq.o
 obj-$(CONFIG_CPU_VOLTAGE) += dpmc.o
diff --git a/arch/blackfin/mach-common/lock.S b/arch/blackfin/mach-common/lock.S
deleted file mode 100644
index 6c5f5f0..0000000
--- a/arch/blackfin/mach-common/lock.S
+++ /dev/null
@@ -1,223 +0,0 @@
-/*
- * File:         arch/blackfin/mach-common/lock.S
- * Based on:
- * Author:       LG Soft India
- *
- * Created:      ?
- * Description:  kernel locks
- *
- * Modified:
- *               Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-
-#include <linux/linkage.h>
-#include <asm/blackfin.h>
-
-.text
-
-/* When you come here, it is assumed that
- * R0 - Which way to be locked
- */
-
-ENTRY(_cache_grab_lock)
-
-	[--SP]=( R7:0,P5:0 );
-
-	P1.H = HI(IMEM_CONTROL);
-	P1.L = LO(IMEM_CONTROL);
-	P5.H = HI(ICPLB_ADDR0);
-	P5.L = LO(ICPLB_ADDR0);
-	P4.H = HI(ICPLB_DATA0);
-	P4.L = LO(ICPLB_DATA0);
-	R7 = R0;
-
-	/* If the code of interest already resides in the cache
-	 * invalidate the entire cache itself.
-	 * invalidate_entire_icache;
-	 */
-
-	SP += -12;
-	[--SP] = RETS;
-	CALL _invalidate_entire_icache;
-	RETS = [SP++];
-	SP += 12;
-
-	/* Disable the Interrupts*/
-
-	CLI R3;
-
-.LLOCK_WAY:
-
-	/* Way0 - 0xFFA133E0
-	 * Way1 - 0xFFA137E0
-	 * Way2 - 0xFFA13BE0	Total Way Size = 4K
-	 * Way3 - 0xFFA13FE0
-	 */
-
-	/* Procedure Ex. -Set the locks for other ways by setting ILOC[3:1]
-	 * Only Way0 of the instruction cache can now be
-	 * replaced by a new code
-	 */
-
-	R5 = R7;
-	CC = BITTST(R7,0);
-	IF CC JUMP .LCLEAR1;
-	R7 = 0;
-	BITSET(R7,0);
-	JUMP .LDONE1;
-
-.LCLEAR1:
-	R7 = 0;
-	BITCLR(R7,0);
-.LDONE1:	R4 = R7 << 3;
-	R7 = [P1];
-	R7 = R7 | R4;
-	SSYNC;		/* SSYNC required writing to IMEM_CONTROL. */
-	.align 8;
-	[P1] = R7;
-	SSYNC;
-
-	R7 = R5;
-	CC = BITTST(R7,1);
-	IF CC JUMP .LCLEAR2;
-	R7 = 0;
-	BITSET(R7,1);
-	JUMP .LDONE2;
-
-.LCLEAR2:
-	R7 = 0;
-	BITCLR(R7,1);
-.LDONE2:	R4 = R7 << 3;
-	R7 = [P1];
-	R7 = R7 | R4;
-	SSYNC;		/* SSYNC required writing to IMEM_CONTROL. */
-	.align 8;
-	[P1] = R7;
-	SSYNC;
-
-	R7 = R5;
-	CC = BITTST(R7,2);
-	IF CC JUMP .LCLEAR3;
-	R7 = 0;
-	BITSET(R7,2);
-	JUMP .LDONE3;
-.LCLEAR3:
-	R7 = 0;
-	BITCLR(R7,2);
-.LDONE3:	R4 = R7 << 3;
-	R7 = [P1];
-	R7 = R7 | R4;
-	SSYNC;		/* SSYNC required writing to IMEM_CONTROL. */
-	.align 8;
-	[P1] = R7;
-	SSYNC;
-
-
-	R7 = R5;
-	CC = BITTST(R7,3);
-	IF CC JUMP .LCLEAR4;
-	R7 = 0;
-	BITSET(R7,3);
-	JUMP .LDONE4;
-.LCLEAR4:
-	R7 = 0;
-	BITCLR(R7,3);
-.LDONE4:	R4 = R7 << 3;
-	R7 = [P1];
-	R7 = R7 | R4;
-	SSYNC;		/* SSYNC required writing to IMEM_CONTROL. */
-	.align 8;
-	[P1] = R7;
-	SSYNC;
-
-	STI R3;
-
-	( R7:0,P5:0 ) = [SP++];
-
-	RTS;
-ENDPROC(_cache_grab_lock)
-
-/* After the execution of critical code, the code is now locked into
- * the cache way. Now we need to set ILOC.
- *
- * R0 - Which way to be locked
- */
-
-ENTRY(_bfin_cache_lock)
-
-	[--SP]=( R7:0,P5:0 );
-
-	P1.H = HI(IMEM_CONTROL);
-	P1.L = LO(IMEM_CONTROL);
-
-	/* Disable the Interrupts*/
-	CLI R3;
-
-	R7 = [P1];
-	R2 = ~(0x78) (X);	/* mask out ILOC */
-	R7 = R7 & R2;
-	R0 = R0 << 3;
-	R7 = R0 | R7;
-	SSYNC;		/* SSYNC required writing to IMEM_CONTROL. */
-	.align 8;
-	[P1] = R7;
-	SSYNC;
-	/* Renable the Interrupts */
-	STI R3;
-
-	( R7:0,P5:0 ) = [SP++];
-	RTS;
-ENDPROC(_bfin_cache_lock)
-
-/* Invalidate the Entire Instruction cache by
- * disabling IMC bit
- */
-ENTRY(_invalidate_entire_icache)
-	[--SP] = ( R7:5);
-
-	P0.L = LO(IMEM_CONTROL);
-	P0.H = HI(IMEM_CONTROL);
-	R7 = [P0];
-
-	/* Clear the IMC bit , All valid bits in the instruction
-	 * cache are set to the invalid state
-	 */
-	BITCLR(R7,IMC_P);
-	CLI R6;
-	SSYNC;		/* SSYNC required before invalidating cache. */
-	.align 8;
-	[P0] = R7;
-	SSYNC;
-	STI R6;
-
-	/* Configures the instruction cache agian */
-	R6 = (IMC | ENICPLB);
-	R7 = R7 | R6;
-
-	CLI R6;
-	SSYNC;		/* SSYNC required before writing to IMEM_CONTROL. */
-	.align 8;
-	[P0] = R7;
-	SSYNC;
-	STI R6;
-
-	( R7:5) = [SP++];
-	RTS;
-ENDPROC(_invalidate_entire_icache)
-- 
1.6.4.2

[PATCH 53/72] Blackfin: delete '-spi' suffix in ad1836/ad1938 driver name

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

The ASoC drivers have dropped the redundant "-spi" suffix in the driver
name, so update the board resources accordingly.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf527/boards/cm_bf527.c  |    2 +-
 arch/blackfin/mach-bf527/boards/ezkit.c     |    2 +-
 arch/blackfin/mach-bf533/boards/H8606.c     |    2 +-
 arch/blackfin/mach-bf533/boards/cm_bf533.c  |    2 +-
 arch/blackfin/mach-bf533/boards/ezkit.c     |    2 +-
 arch/blackfin/mach-bf533/boards/stamp.c     |    2 +-
 arch/blackfin/mach-bf537/boards/cm_bf537.c  |    2 +-
 arch/blackfin/mach-bf537/boards/pnav10.c    |    2 +-
 arch/blackfin/mach-bf537/boards/stamp.c     |    4 ++--
 arch/blackfin/mach-bf537/boards/tcm_bf537.c |    2 +-
 arch/blackfin/mach-bf548/boards/ezkit.c     |    2 +-
 arch/blackfin/mach-bf561/boards/cm_bf561.c  |    2 +-
 arch/blackfin/mach-bf561/boards/ezkit.c     |    2 +-
 13 files changed, 14 insertions(+), 14 deletions(-)

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index fdd518c..a0f623d 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -568,7 +568,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c
index 4ab9cfa..2849b09 100644
--- a/arch/blackfin/mach-bf527/boards/ezkit.c
+++ b/arch/blackfin/mach-bf527/boards/ezkit.c
@@ -609,7 +609,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf533/boards/H8606.c b/arch/blackfin/mach-bf533/boards/H8606.c
index 30ff3c4..6c2b47f 100644
--- a/arch/blackfin/mach-bf533/boards/H8606.c
+++ b/arch/blackfin/mach-bf533/boards/H8606.c
@@ -231,7 +231,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 16,
 		.bus_num = 1,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index 7052568..ef31bc5 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -130,7 +130,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf533/boards/ezkit.c b/arch/blackfin/mach-bf533/boards/ezkit.c
index 88b2dfc..fd518e3 100644
--- a/arch/blackfin/mach-bf533/boards/ezkit.c
+++ b/arch/blackfin/mach-bf533/boards/ezkit.c
@@ -274,7 +274,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf533/boards/stamp.c b/arch/blackfin/mach-bf533/boards/stamp.c
index 3954baa..729fd7c 100644
--- a/arch/blackfin/mach-bf533/boards/stamp.c
+++ b/arch/blackfin/mach-bf533/boards/stamp.c
@@ -281,7 +281,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 159e5b2..220cfda 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -135,7 +135,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 0d93bbe..10b35b8 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -352,7 +352,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index d5aabee..7ce7d94 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -870,7 +870,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 	|| defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
@@ -881,7 +881,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BF5XX_SOC_AD1938) || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
 	{
-		.modalias = "ad1938-spi",
+		.modalias = "ad1938",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 0,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 88eade8..dc4f161 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -135,7 +135,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index 3c06010..e50d136 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -702,7 +702,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 1,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index cedcc3c..5721620 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -132,7 +132,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 
 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
diff --git a/arch/blackfin/mach-bf561/boards/ezkit.c b/arch/blackfin/mach-bf561/boards/ezkit.c
index 10edc99..caed96b 100644
--- a/arch/blackfin/mach-bf561/boards/ezkit.c
+++ b/arch/blackfin/mach-bf561/boards/ezkit.c
@@ -345,7 +345,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 	{
-		.modalias = "ad1836-spi",
+		.modalias = "ad1836",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
-- 
1.6.4.2

[PATCH 54/72] Blackfin: optimize fixed code handling for the most common case

[Mike Frysinger]

The majority of the time we are returning to user space, it is not in the
fixed atomic code region.  So rather than branch to a function where we
check the PC and return, do the check inline and branch only when needed.

Also, tweak some of the fixed code handling based on assumptions we are
aware of but cannot be expressed in C.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/process.c    |   10 ++--------
 arch/blackfin/mach-common/entry.S |    6 ++++++
 2 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/blackfin/kernel/process.c b/arch/blackfin/kernel/process.c
index 9da36ba..f5b2861 100644
--- a/arch/blackfin/kernel/process.c
+++ b/arch/blackfin/kernel/process.c
@@ -282,25 +282,19 @@ void finish_atomic_sections (struct pt_regs *regs)
 {
 	int __user *up0 = (int __user *)regs->p0;
 
-	if (regs->pc < ATOMIC_SEQS_START || regs->pc >= ATOMIC_SEQS_END)
-		return;
-
 	switch (regs->pc) {
 	case ATOMIC_XCHG32 + 2:
 		put_user(regs->r1, up0);
-		regs->pc += 2;
+		regs->pc = ATOMIC_XCHG32 + 4;
 		break;
 
 	case ATOMIC_CAS32 + 2:
 	case ATOMIC_CAS32 + 4:
 		if (regs->r0 == regs->r1)
+	case ATOMIC_CAS32 + 6:
 			put_user(regs->r2, up0);
 		regs->pc = ATOMIC_CAS32 + 8;
 		break;
-	case ATOMIC_CAS32 + 6:
-		put_user(regs->r2, up0);
-		regs->pc += 2;
-		break;
 
 	case ATOMIC_ADD32 + 2:
 		regs->r0 = regs->r1 + regs->r0;
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index e7eb163..a9b15aa 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -1025,6 +1025,12 @@ ENTRY(_schedule_and_signal_from_int)
 #endif
 	sti r0;
 
+	/* finish the userspace "atomic" functions for it */
+	r1 = FIXED_CODE_END;
+	r2 = [sp + PT_PC];
+	cc = r1 <= r2;
+	if cc jump .Lresume_userspace (bp);
+
 	r0 = sp;
 	sp += -12;
 	call _finish_atomic_sections;
-- 
1.6.4.2

[PATCH 55/72] Blackfin: handle the core timer interrupt with handle_percpu_irq on SMP

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-common/ints-priority.c |   17 ++++++++++-------
 1 files changed, 10 insertions(+), 7 deletions(-)

diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c
index 4cc55bc..6ffda78 100644
--- a/arch/blackfin/mach-common/ints-priority.c
+++ b/arch/blackfin/mach-common/ints-priority.c
@@ -1052,18 +1052,26 @@ int __init init_arch_irq(void)
 			set_irq_chained_handler(irq, bfin_demux_error_irq);
 			break;
 #endif
+
 #ifdef CONFIG_SMP
+#ifdef CONFIG_TICKSOURCE_GPTMR0
+		case IRQ_TIMER0:
+#endif
+#ifdef CONFIG_TICKSOURCE_CORETMR
+		case IRQ_CORETMR:
+#endif
 		case IRQ_SUPPLE_0:
 		case IRQ_SUPPLE_1:
 			set_irq_handler(irq, handle_percpu_irq);
 			break;
 #endif
+
 #ifdef CONFIG_IPIPE
 #ifndef CONFIG_TICKSOURCE_CORETMR
 		case IRQ_TIMER0:
 			set_irq_handler(irq, handle_simple_irq);
 			break;
-#endif /* !CONFIG_TICKSOURCE_CORETMR */
+#endif
 		case IRQ_CORETMR:
 			set_irq_handler(irq, handle_simple_irq);
 			break;
@@ -1071,15 +1079,10 @@ int __init init_arch_irq(void)
 			set_irq_handler(irq, handle_level_irq);
 			break;
 #else /* !CONFIG_IPIPE */
-#ifdef CONFIG_TICKSOURCE_GPTMR0
-		case IRQ_TIMER0:
-			set_irq_handler(irq, handle_percpu_irq);
-			break;
-#endif /* CONFIG_TICKSOURCE_GPTMR0 */
 		default:
 			set_irq_handler(irq, handle_simple_irq);
 			break;
-#endif	/* !CONFIG_IPIPE */
+#endif /* !CONFIG_IPIPE */
 		}
 	}
 
-- 
1.6.4.2

[PATCH 56/72] Blackfin: Fix link errors with binutils 2.19 and GCC 4.3

[Mike Frysinger]

From: Ingo Molnar <mingo@elte.hu>

Not sure whether this has been reported/fixed before.

Today I built a Blackfin tool-chain from scratch for -tip testing,
and it triggers:

 arch/blackfin/kernel/vmlinux.lds:1238: undefined section `.data_a_l1' referenced in expression

and:

 arch/blackfin/kernel/vmlinux.lds:1238: undefined section `.text_data_l1'
referenced in expression

Now i dont have any way to test this linker script, but it now at
least builds fine after fixing what appears to be typos in those
assert statements.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/vmlinux.lds.S |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/kernel/vmlinux.lds.S b/arch/blackfin/kernel/vmlinux.lds.S
index 6ac307c..77f8659 100644
--- a/arch/blackfin/kernel/vmlinux.lds.S
+++ b/arch/blackfin/kernel/vmlinux.lds.S
@@ -221,7 +221,7 @@ SECTIONS
 		. = ALIGN(4);
 		__ebss_l1 = .;
 	}
-	ASSERT (SIZEOF(.data_a_l1) <= L1_DATA_A_LENGTH, "L1 data A overflow!")
+	ASSERT (SIZEOF(.data_l1) <= L1_DATA_A_LENGTH, "L1 data A overflow!")
 
 	.data_b_l1 L1_DATA_B_START : AT(LOADADDR(.data_l1) + SIZEOF(.data_l1))
 	{
@@ -262,7 +262,7 @@ SECTIONS
 		. = ALIGN(4);
 		__ebss_l2 = .;
 	}
-	ASSERT (SIZEOF(.text_data_l1) <= L2_LENGTH, "L2 overflow!")
+	ASSERT (SIZEOF(.text_data_l2) <= L2_LENGTH, "L2 overflow!")
 
 	/* Force trailing alignment of our init section so that when we
 	 * free our init memory, we don't leave behind a partial page.
-- 
1.6.4.2

[PATCH 57/72] Blackfin: remove useless duplicated assignment in gpio code

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/bfin_gpio.c |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/kernel/bfin_gpio.c b/arch/blackfin/kernel/bfin_gpio.c
index 6b94462..fc4681c 100644
--- a/arch/blackfin/kernel/bfin_gpio.c
+++ b/arch/blackfin/kernel/bfin_gpio.c
@@ -722,7 +722,6 @@ void bfin_gpio_pm_hibernate_suspend(void)
 		gpio_bank_saved[bank].fer = gpio_array[bank]->port_fer;
 		gpio_bank_saved[bank].mux = gpio_array[bank]->port_mux;
 		gpio_bank_saved[bank].data = gpio_array[bank]->data;
-		gpio_bank_saved[bank].data = gpio_array[bank]->data;
 		gpio_bank_saved[bank].inen = gpio_array[bank]->inen;
 		gpio_bank_saved[bank].dir = gpio_array[bank]->dir_set;
 	}
-- 
1.6.4.2

[PATCH 58/72] Blackfin: use raw_smp_processor_id() in exception code

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

When preempt debugging is enabled, smp_processor_id() may utilize the
"current" structure.  This may not be safe to access under all exceptions
due to it being in dynamically allocated memory.  So in exception code,
make sure we use raw_smp_processor_id() instead to get at the real value
directly.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/cplb-mpu/cplbmgr.c   |    2 +-
 arch/blackfin/kernel/cplb-nompu/cplbmgr.c |    2 +-
 arch/blackfin/kernel/traps.c              |   12 ++++++------
 3 files changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/blackfin/kernel/cplb-mpu/cplbmgr.c b/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
index 651b127..8e1e9e9 100644
--- a/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
+++ b/arch/blackfin/kernel/cplb-mpu/cplbmgr.c
@@ -280,7 +280,7 @@ static noinline int dcplb_protection_fault(unsigned int cpu)
 int cplb_hdr(int seqstat, struct pt_regs *regs)
 {
 	int cause = seqstat & 0x3f;
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu = raw_smp_processor_id();
 	switch (cause) {
 	case 0x23:
 		return dcplb_protection_fault(cpu);
diff --git a/arch/blackfin/kernel/cplb-nompu/cplbmgr.c b/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
index aabbb42..d9ea46c 100644
--- a/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
+++ b/arch/blackfin/kernel/cplb-nompu/cplbmgr.c
@@ -202,7 +202,7 @@ MGR_ATTR static int dcplb_miss(int cpu)
 MGR_ATTR int cplb_hdr(int seqstat, struct pt_regs *regs)
 {
 	int cause = seqstat & 0x3f;
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu = raw_smp_processor_id();
 	switch (cause) {
 	case VEC_CPLB_I_M:
 		return icplb_miss(cpu);
diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 7b3ba06..56464cb 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -227,7 +227,7 @@ asmlinkage void double_fault_c(struct pt_regs *fp)
 	printk(KERN_EMERG "Double Fault\n");
 #ifdef CONFIG_DEBUG_DOUBLEFAULT_PRINT
 	if (((long)fp->seqstat &  SEQSTAT_EXCAUSE) == VEC_UNCOV) {
-		unsigned int cpu = smp_processor_id();
+		unsigned int cpu = raw_smp_processor_id();
 		char buf[150];
 		decode_address(buf, cpu_pda[cpu].retx_doublefault);
 		printk(KERN_EMERG "While handling exception (EXCAUSE = 0x%x) at %s:\n",
@@ -263,7 +263,7 @@ asmlinkage notrace void trap_c(struct pt_regs *fp)
 	int j;
 #endif
 #ifdef CONFIG_DEBUG_HUNT_FOR_ZERO
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu = raw_smp_processor_id();
 #endif
 	const char *strerror = NULL;
 	int sig = 0;
@@ -1098,7 +1098,7 @@ void show_regs(struct pt_regs *fp)
 	struct irqaction *action;
 	unsigned int i;
 	unsigned long flags = 0;
-	unsigned int cpu = smp_processor_id();
+	unsigned int cpu = raw_smp_processor_id();
 	unsigned char in_atomic = (bfin_read_IPEND() & 0x10) || in_atomic();
 
 	verbose_printk(KERN_NOTICE "\n");
@@ -1126,13 +1126,13 @@ void show_regs(struct pt_regs *fp)
 
 	verbose_printk(KERN_NOTICE "\nSEQUENCER STATUS:\t\t%s\n", print_tainted());
 	verbose_printk(KERN_NOTICE " SEQSTAT: %08lx  IPEND: %04lx  IMASK: %04lx  SYSCFG: %04lx\n",
-		(long)fp->seqstat, fp->ipend, cpu_pda[smp_processor_id()].ex_imask, fp->syscfg);
+		(long)fp->seqstat, fp->ipend, cpu_pda[raw_smp_processor_id()].ex_imask, fp->syscfg);
 	if (fp->ipend & EVT_IRPTEN)
 		verbose_printk(KERN_NOTICE "  Global Interrupts Disabled (IPEND[4])\n");
-	if (!(cpu_pda[smp_processor_id()].ex_imask & (EVT_IVG13 | EVT_IVG12 | EVT_IVG11 |
+	if (!(cpu_pda[raw_smp_processor_id()].ex_imask & (EVT_IVG13 | EVT_IVG12 | EVT_IVG11 |
 			EVT_IVG10 | EVT_IVG9 | EVT_IVG8 | EVT_IVG7 | EVT_IVTMR)))
 		verbose_printk(KERN_NOTICE "  Peripheral interrupts masked off\n");
-	if (!(cpu_pda[smp_processor_id()].ex_imask & (EVT_IVG15 | EVT_IVG14)))
+	if (!(cpu_pda[raw_smp_processor_id()].ex_imask & (EVT_IVG15 | EVT_IVG14)))
 		verbose_printk(KERN_NOTICE "  Kernel interrupts masked off\n");
 	if ((fp->seqstat & SEQSTAT_EXCAUSE) == VEC_HWERR) {
 		verbose_printk(KERN_NOTICE "  HWERRCAUSE: 0x%lx\n",
-- 
1.6.4.2

[PATCH 59/72] Blackfin: fix spelling in a few comments

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/setup.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index ce02f98..369535b 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -112,7 +112,7 @@ void __cpuinit bfin_setup_caches(unsigned int cpu)
 	/*
 	 * In cache coherence emulation mode, we need to have the
 	 * D-cache enabled before running any atomic operation which
-	 * might invove cache invalidation (i.e. spinlock, rwlock).
+	 * might involve cache invalidation (i.e. spinlock, rwlock).
 	 * So printk's are deferred until then.
 	 */
 #ifdef CONFIG_BFIN_ICACHE
@@ -699,7 +699,7 @@ static __init void setup_bootmem_allocator(void)
 	sanitize_memmap(bfin_memmap.map, &bfin_memmap.nr_map);
 	print_memory_map("boot memmap");
 
-	/* intialize globals in linux/bootmem.h */
+	/* initialize globals in linux/bootmem.h */
 	find_min_max_pfn();
 	/* pfn of the last usable page frame */
 	if (max_pfn > memory_end >> PAGE_SHIFT)
-- 
1.6.4.2

[PATCH 60/72] Blackfin: workaround anomaly 05000283

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

Make sure our interrupt entry code with exact hardware errors handles
anomaly 05000283 (infinite stall in system MMR kill) so we don't stall
while under load.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/include/asm/entry.h     |   30 ++++++++++++++++++++++++++----
 arch/blackfin/mach-common/entry.S     |   18 ++----------------
 arch/blackfin/mach-common/interrupt.S |   19 +++----------------
 3 files changed, 31 insertions(+), 36 deletions(-)

diff --git a/arch/blackfin/include/asm/entry.h b/arch/blackfin/include/asm/entry.h
index ec58efc..55b808f 100644
--- a/arch/blackfin/include/asm/entry.h
+++ b/arch/blackfin/include/asm/entry.h
@@ -36,6 +36,21 @@
 # define LOAD_IPIPE_IPEND
 #endif
 
+/*
+ * Workaround for anomalies 05000283 and 05000315
+ */
+#if ANOMALY_05000283 || ANOMALY_05000315
+# define ANOMALY_283_315_WORKAROUND(preg, dreg)		\
+	cc = dreg == dreg;				\
+	preg.h = HI(CHIPID);				\
+	preg.l = LO(CHIPID);				\
+	if cc jump 1f;					\
+	dreg.l = W[preg];				\
+1:
+#else
+# define ANOMALY_283_315_WORKAROUND(preg, dreg)
+#endif /* ANOMALY_05000283 || ANOMALY_05000315 */
+
 #ifndef CONFIG_EXACT_HWERR
 /* As a debugging aid - we save IPEND when DEBUG_KERNEL is on,
  * otherwise it is a waste of cycles.
@@ -88,17 +103,22 @@
  * As you can see by the code - we actually need to do two SSYNCS - one to
  * make sure the read/writes complete, and another to make sure the hardware
  * error is recognized by the core.
+ *
+ * The extra nop before the SSYNC is to make sure we work around 05000244,
+ * since the 283/315 workaround includes a branch to the end
  */
 #define INTERRUPT_ENTRY(N)						\
-    SSYNC;								\
-    SSYNC;								\
     [--sp] = SYSCFG;							\
     [--sp] = P0;	/*orig_p0*/					\
     [--sp] = R0;	/*orig_r0*/					\
     [--sp] = (R7:0,P5:0);						\
     R1 = ASTAT;								\
+    ANOMALY_283_315_WORKAROUND(p0, r0)					\
     P0.L = LO(ILAT);							\
     P0.H = HI(ILAT);							\
+    NOP;								\
+    SSYNC;								\
+    SSYNC;								\
     R0 = [P0];								\
     CC = BITTST(R0, EVT_IVHW_P);					\
     IF CC JUMP 1f;							\
@@ -118,15 +138,17 @@
     RTI;
 
 #define TIMER_INTERRUPT_ENTRY(N)					\
-    SSYNC;								\
-    SSYNC;								\
     [--sp] = SYSCFG;							\
     [--sp] = P0;	/*orig_p0*/					\
     [--sp] = R0;	/*orig_r0*/					\
     [--sp] = (R7:0,P5:0);						\
     R1 = ASTAT;								\
+    ANOMALY_283_315_WORKAROUND(p0, r0)					\
     P0.L = LO(ILAT);							\
     P0.H = HI(ILAT);							\
+    NOP;								\
+    SSYNC;								\
+    SSYNC;								\
     R0 = [P0];								\
     CC = BITTST(R0, EVT_IVHW_P);					\
     IF CC JUMP 1f;							\
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index a9b15aa..01af24c 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -513,14 +513,7 @@ ENTRY(_trap) /* Exception: 4th entry into system event table(supervisor mode)*/
 	ssync;
 #endif
 
-#if ANOMALY_05000283 || ANOMALY_05000315
-	cc = r7 == r7;
-	p5.h = HI(CHIPID);
-	p5.l = LO(CHIPID);
-	if cc jump 1f;
-	r7.l = W[p5];
-1:
-#endif
+	ANOMALY_283_315_WORKAROUND(p5, r7)
 
 #ifdef CONFIG_DEBUG_DOUBLEFAULT
 	/*
@@ -1134,14 +1127,7 @@ ENTRY(_early_trap)
 	SAVE_ALL_SYS
 	trace_buffer_stop(p0,r0);
 
-#if ANOMALY_05000283 || ANOMALY_05000315
-	cc = r5 == r5;
-	p4.h = HI(CHIPID);
-	p4.l = LO(CHIPID);
-	if cc jump 1f;
-	r5.l = W[p4];
-1:
-#endif
+	ANOMALY_283_315_WORKAROUND(p4, r5)
 
 	/* Turn caches off, to ensure we don't get double exceptions */
 
diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index c754ff7..82d417e 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -119,14 +119,8 @@ __common_int_entry:
 	fp = 0;
 #endif
 
-#if ANOMALY_05000283 || ANOMALY_05000315
-	cc = r7 == r7;
-	p5.h = HI(CHIPID);
-	p5.l = LO(CHIPID);
-	if cc jump 1f;
-	r7.l = W[p5];
-1:
-#endif
+	ANOMALY_283_315_WORKAROUND(p5, r7)
+
 	r1 =  sp;
 	SP += -12;
 #ifdef CONFIG_IPIPE
@@ -158,14 +152,7 @@ ENTRY(_evt_ivhw)
 	fp = 0;
 #endif
 
-#if ANOMALY_05000283 || ANOMALY_05000315
-	cc = r7 == r7;
-	p5.h = HI(CHIPID);
-	p5.l = LO(CHIPID);
-	if cc jump 1f;
-	r7.l = W[p5];
-1:
-#endif
+	ANOMALY_283_315_WORKAROUND(p5, r7)
 
 	/* Handle all stacked hardware errors
 	 * To make sure we don't hang forever, only do it 10 times
-- 
1.6.4.2

[PATCH 61/72] Blackfin: add some isram-driver self tests

[Mike Frysinger]

Make it easy to figure out if code changes here are correct.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig.debug     |    6 +
 arch/blackfin/mm/isram-driver.c |  212 ++++++++++++++++++++++++++++++++++++++-
 2 files changed, 216 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/Kconfig.debug b/arch/blackfin/Kconfig.debug
index 1fc4981..87f195e 100644
--- a/arch/blackfin/Kconfig.debug
+++ b/arch/blackfin/Kconfig.debug
@@ -252,4 +252,10 @@ config ACCESS_CHECK
 
 	  Say N here to disable that check to improve the performance.
 
+config BFIN_ISRAM_SELF_TEST
+	bool "isram boot self tests"
+	default n
+	help
+	  Run some self tests of the isram driver code at boot.
+
 endmenu
diff --git a/arch/blackfin/mm/isram-driver.c b/arch/blackfin/mm/isram-driver.c
index c080e70..02eaaa6 100644
--- a/arch/blackfin/mm/isram-driver.c
+++ b/arch/blackfin/mm/isram-driver.c
@@ -16,6 +16,8 @@
  * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  */
 
+#define pr_fmt(fmt) "isram: " fmt
+
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/types.h>
@@ -23,6 +25,7 @@
 #include <linux/sched.h>
 
 #include <asm/blackfin.h>
+#include <asm/dma.h>
 
 /*
  * IMPORTANT WARNING ABOUT THESE FUNCTIONS
@@ -127,8 +130,7 @@ static bool isram_check_addr(const void *addr, size_t n)
 	    (addr < (void *)(L1_CODE_START + L1_CODE_LENGTH))) {
 		if ((addr + n) > (void *)(L1_CODE_START + L1_CODE_LENGTH)) {
 			show_stack(NULL, NULL);
-			printk(KERN_ERR "isram_memcpy: copy involving %p length "
-					"(%zu) too long\n", addr, n);
+			pr_err("copy involving %p length (%zu) too long\n", addr, n);
 		}
 		return true;
 	}
@@ -199,3 +201,209 @@ void *isram_memcpy(void *dest, const void *src, size_t n)
 }
 EXPORT_SYMBOL(isram_memcpy);
 
+#ifdef CONFIG_BFIN_ISRAM_SELF_TEST
+
+#define TEST_LEN 0x100
+
+static __init void hex_dump(unsigned char *buf, int len)
+{
+	while (len--)
+		pr_cont("%02x", *buf++);
+}
+
+static __init int isram_read_test(char *sdram, void *l1inst)
+{
+	int i, ret = 0;
+	uint64_t data1, data2;
+
+	pr_info("INFO: running isram_read tests\n");
+
+	/* setup some different data to play with */
+	for (i = 0; i < TEST_LEN; ++i)
+		sdram[i] = i;
+	dma_memcpy(l1inst, sdram, TEST_LEN);
+
+	/* make sure we can read the L1 inst */
+	for (i = 0; i < TEST_LEN; i += sizeof(uint64_t)) {
+		data1 = isram_read(l1inst + i);
+		memcpy(&data2, sdram + i, sizeof(data2));
+		if (memcmp(&data1, &data2, sizeof(uint64_t))) {
+			pr_err("FAIL: isram_read(%p) returned %#llx but wanted %#llx\n",
+				l1inst + i, data1, data2);
+			++ret;
+		}
+	}
+
+	return ret;
+}
+
+static __init int isram_write_test(char *sdram, void *l1inst)
+{
+	int i, ret = 0;
+	uint64_t data1, data2;
+
+	pr_info("INFO: running isram_write tests\n");
+
+	/* setup some different data to play with */
+	memset(sdram, 0, TEST_LEN * 2);
+	dma_memcpy(l1inst, sdram, TEST_LEN);
+	for (i = 0; i < TEST_LEN; ++i)
+		sdram[i] = i;
+
+	/* make sure we can write the L1 inst */
+	for (i = 0; i < TEST_LEN; i += sizeof(uint64_t)) {
+		memcpy(&data1, sdram + i, sizeof(data1));
+		isram_write(l1inst + i, data1);
+		data2 = isram_read(l1inst + i);
+		if (memcmp(&data1, &data2, sizeof(uint64_t))) {
+			pr_err("FAIL: isram_write(%p, %#llx) != %#llx\n",
+				l1inst + i, data1, data2);
+			++ret;
+		}
+	}
+
+	dma_memcpy(sdram + TEST_LEN, l1inst, TEST_LEN);
+	if (memcmp(sdram, sdram + TEST_LEN, TEST_LEN)) {
+		pr_err("FAIL: isram_write() did not work properly\n");
+		++ret;
+	}
+
+	return ret;
+}
+
+static __init int
+_isram_memcpy_test(char pattern, void *sdram, void *l1inst, const char *smemcpy,
+                   void *(*fmemcpy)(void *, const void *, size_t))
+{
+	memset(sdram, pattern, TEST_LEN);
+	fmemcpy(l1inst, sdram, TEST_LEN);
+	fmemcpy(sdram + TEST_LEN, l1inst, TEST_LEN);
+	if (memcmp(sdram, sdram + TEST_LEN, TEST_LEN)) {
+		pr_err("FAIL: %s(%p <=> %p, %#x) failed (data is %#x)\n",
+			smemcpy, l1inst, sdram, TEST_LEN, pattern);
+		return 1;
+	}
+	return 0;
+}
+#define _isram_memcpy_test(a, b, c, d) _isram_memcpy_test(a, b, c, #d, d)
+
+static __init int isram_memcpy_test(char *sdram, void *l1inst)
+{
+	int i, j, thisret, ret = 0;
+
+	/* check broad isram_memcpy() */
+	pr_info("INFO: running broad isram_memcpy tests\n");
+	for (i = 0xf; i >= 0; --i)
+		ret += _isram_memcpy_test(i, sdram, l1inst, isram_memcpy);
+
+	/* check read of small, unaligned, and hardware 64bit limits */
+	pr_info("INFO: running isram_memcpy (read) tests\n");
+
+	for (i = 0; i < TEST_LEN; ++i)
+		sdram[i] = i;
+	dma_memcpy(l1inst, sdram, TEST_LEN);
+
+	thisret = 0;
+	for (i = 0; i < TEST_LEN - 32; ++i) {
+		unsigned char cmp[32];
+		for (j = 1; j <= 32; ++j) {
+			memset(cmp, 0, sizeof(cmp));
+			isram_memcpy(cmp, l1inst + i, j);
+			if (memcmp(cmp, sdram + i, j)) {
+				pr_err("FAIL: %p:", l1inst + 1);
+				hex_dump(cmp, j);
+				pr_cont(" SDRAM:");
+				hex_dump(sdram + i, j);
+				pr_cont("\n");
+				if (++thisret > 20) {
+					pr_err("FAIL: skipping remaining series\n");
+					i = TEST_LEN;
+					break;
+				}
+			}
+		}
+	}
+	ret += thisret;
+
+	/* check write of small, unaligned, and hardware 64bit limits */
+	pr_info("INFO: running isram_memcpy (write) tests\n");
+
+	memset(sdram + TEST_LEN, 0, TEST_LEN);
+	dma_memcpy(l1inst, sdram + TEST_LEN, TEST_LEN);
+
+	thisret = 0;
+	for (i = 0; i < TEST_LEN - 32; ++i) {
+		unsigned char cmp[32];
+		for (j = 1; j <= 32; ++j) {
+			isram_memcpy(l1inst + i, sdram + i, j);
+			dma_memcpy(cmp, l1inst + i, j);
+			if (memcmp(cmp, sdram + i, j)) {
+				pr_err("FAIL: %p:", l1inst + i);
+				hex_dump(cmp, j);
+				pr_cont(" SDRAM:");
+				hex_dump(sdram + i, j);
+				pr_cont("\n");
+				if (++thisret > 20) {
+					pr_err("FAIL: skipping remaining series\n");
+					i = TEST_LEN;
+					break;
+				}
+			}
+		}
+	}
+	ret += thisret;
+
+	return ret;
+}
+
+static __init int isram_test_init(void)
+{
+	int ret;
+	char *sdram;
+	void *l1inst;
+
+	sdram = kmalloc(TEST_LEN * 2, GFP_KERNEL);
+	if (!sdram) {
+		pr_warning("SKIP: could not allocate sdram\n");
+		return 0;
+	}
+
+	l1inst = l1_inst_sram_alloc(TEST_LEN);
+	if (!l1inst) {
+		kfree(sdram);
+		pr_warning("SKIP: could not allocate L1 inst\n");
+		return 0;
+	}
+
+	/* sanity check initial L1 inst state */
+	ret = 1;
+	pr_info("INFO: running initial dma_memcpy checks\n");
+	if (_isram_memcpy_test(0xa, sdram, l1inst, dma_memcpy))
+		goto abort;
+	if (_isram_memcpy_test(0x5, sdram, l1inst, dma_memcpy))
+		goto abort;
+
+	ret = 0;
+	ret += isram_read_test(sdram, l1inst);
+	ret += isram_write_test(sdram, l1inst);
+	ret += isram_memcpy_test(sdram, l1inst);
+
+ abort:
+	sram_free(l1inst);
+	kfree(sdram);
+
+	if (ret)
+		return -EIO;
+
+	pr_info("PASS: all tests worked !\n");
+	return 0;
+}
+late_initcall(isram_test_init);
+
+static __exit void isram_test_exit(void)
+{
+	/* stub to allow unloading */
+}
+module_exit(isram_test_exit);
+
+#endif
-- 
1.6.4.2

[PATCH 62/72] Blackfin: bf537-stamp: add adp5588 gpio resources

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich@analog.com>

For the adp5588 GPIO daughter card.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf537/boards/stamp.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf537/boards/stamp.c b/arch/blackfin/mach-bf537/boards/stamp.c
index 7ce7d94..9db6b40 100644
--- a/arch/blackfin/mach-bf537/boards/stamp.c
+++ b/arch/blackfin/mach-bf537/boards/stamp.c
@@ -1437,6 +1437,14 @@ static struct adp5520_platform_data adp5520_pdev_data = {
 
 #endif
 
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+#include <linux/i2c/adp5588.h>
+static struct adp5588_gpio_platfrom_data adp5588_gpio_data = {
+	.gpio_start = 50,
+	.pullup_dis_mask = 0,
+};
+#endif
+
 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 #if defined(CONFIG_INPUT_EVAL_AD7142EB)
 	{
@@ -1484,6 +1492,12 @@ static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 		.platform_data = (void *)&adxl34x_info,
 	},
 #endif
+#if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
+	{
+		I2C_BOARD_INFO("adp5588-gpio", 0x34),
+		.platform_data = (void *)&adp5588_gpio_data,
+	},
+#endif
 };
 
 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-- 
1.6.4.2

[PATCH 63/72] Blackfin: fix typo in isram_write()

[Mike Frysinger]

From: Robin Getz <robin.getz@analog.com>

The DTEST write bit is 2, not 1.  Improve comments in the related macro
while we're here.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mm/isram-driver.c |   10 ++++++----
 1 files changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/mm/isram-driver.c b/arch/blackfin/mm/isram-driver.c
index 02eaaa6..beb1a60 100644
--- a/arch/blackfin/mm/isram-driver.c
+++ b/arch/blackfin/mm/isram-driver.c
@@ -53,10 +53,12 @@ static DEFINE_SPINLOCK(dtest_lock);
 #define IADDR2DTEST(x) \
 	({ unsigned long __addr = (unsigned long)(x); \
 		(__addr & 0x47F8)        | /* address bits 14 & 10:3 */ \
+		(__addr & 0x8000) << 23  | /* Bank A/B               */ \
 		(__addr & 0x0800) << 15  | /* address bit  11        */ \
-		(__addr  & 0x3000) << 4  | /* address bits 13:12     */ \
-		(__addr  & 0x8000) << 8  | /* address bit  15        */ \
-		(0x1000004);               /* isram access           */ \
+		(__addr & 0x3000) <<  4  | /* address bits 13:12     */ \
+		(__addr & 0x8000) <<  8  | /* address bit  15        */ \
+		(0x1000000)              | /* instruction access = 1 */ \
+		(0x4);                     /* data array = 1         */ \
 	})
 
 /* Takes a pointer, and returns the offset (in bits) which things should be shifted */
@@ -73,7 +75,7 @@ static void isram_write(const void *addr, uint64_t data)
 	if (addr >= (void *)(L1_CODE_START + L1_CODE_LENGTH))
 		return;
 
-	cmd = IADDR2DTEST(addr) | 1;             /* write */
+	cmd = IADDR2DTEST(addr) | 2;             /* write */
 
 	/*
 	 * Writes to DTEST_DATA[0:1] need to be atomic with write to DTEST_COMMAND
-- 
1.6.4.2

[PATCH 64/72] Blackfin: fix BF54x SPI CS resources

[Mike Frysinger]

From: Yi Li <yi.li@analog.com>

The BF54x has three slave select signals for SPI0/SPI1, not eight.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf548/boards/cm_bf548.c |    4 ++--
 arch/blackfin/mach-bf548/boards/ezkit.c    |    4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
index f5a3c30..290b6e9 100644
--- a/arch/blackfin/mach-bf548/boards/cm_bf548.c
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -642,7 +642,7 @@ static struct resource bfin_spi1_resource[] = {
 
 /* SPI controller data */
 static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
-	.num_chipselect = 8,
+	.num_chipselect = 3,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -658,7 +658,7 @@ static struct platform_device bf54x_spi_master0 = {
 };
 
 static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
-	.num_chipselect = 8,
+	.num_chipselect = 3,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index e50d136..c66f380 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -783,7 +783,7 @@ static struct resource bfin_spi1_resource[] = {
 
 /* SPI controller data */
 static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
-	.num_chipselect = 8,
+	.num_chipselect = 3,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };
@@ -799,7 +799,7 @@ static struct platform_device bf54x_spi_master0 = {
 };
 
 static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
-	.num_chipselect = 8,
+	.num_chipselect = 3,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
 };
-- 
1.6.4.2

[PATCH 65/72] Blackfin: use KERN_ALERT in all kgdb_test output

[Mike Frysinger]

From: Mingquan Pan <grace.pan@analog.com>

Most messages are already using KERN_ALERT, so be consistent to make
things easier to check with test scripts.

Signed-off-by: Mingquan Pan <grace.pan@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/kgdb_test.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/kernel/kgdb_test.c b/arch/blackfin/kernel/kgdb_test.c
index dbcf3e4..59fc42d 100644
--- a/arch/blackfin/kernel/kgdb_test.c
+++ b/arch/blackfin/kernel/kgdb_test.c
@@ -54,7 +54,7 @@ void kgdb_l2_test(void)
 
 int kgdb_test(char *name, int len, int count, int z)
 {
-	printk(KERN_DEBUG "kgdb name(%d): %s, %d, %d\n", len, name, count, z);
+	printk(KERN_ALERT "kgdb name(%d): %s, %d, %d\n", len, name, count, z);
 	count = z;
 	return count;
 }
-- 
1.6.4.2

[PATCH 66/72] Blackfin: add ICPLB coverage for async banks

[Mike Frysinger]

From: Bernd Schmidt <bernds_cb1@t-online.de>

When doing XIP, we need to execute out of the async banks, so we need
ICPLBs to allow this.

Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/cplb-nompu/cplbinit.c |   11 +++++++++--
 1 files changed, 9 insertions(+), 2 deletions(-)

diff --git a/arch/blackfin/kernel/cplb-nompu/cplbinit.c b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
index 685f160..5d8ad50 100644
--- a/arch/blackfin/kernel/cplb-nompu/cplbinit.c
+++ b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
@@ -36,7 +36,7 @@ int first_switched_icplb PDT_ATTR;
 int first_switched_dcplb PDT_ATTR;
 
 struct cplb_boundary dcplb_bounds[9] PDT_ATTR;
-struct cplb_boundary icplb_bounds[7] PDT_ATTR;
+struct cplb_boundary icplb_bounds[9] PDT_ATTR;
 
 int icplb_nr_bounds PDT_ATTR;
 int dcplb_nr_bounds PDT_ATTR;
@@ -167,14 +167,21 @@ void __init generate_cplb_tables_all(void)
 		icplb_bounds[i_i++].data = (reserved_mem_icache_on ?
 					    SDRAM_IGENERIC : SDRAM_INON_CHBL);
 	}
+	/* Addressing hole up to the async bank.  */
+	icplb_bounds[i_i].eaddr = ASYNC_BANK0_BASE;
+	icplb_bounds[i_i++].data = 0;
+	/* ASYNC banks.  */
+	icplb_bounds[i_i].eaddr = ASYNC_BANK3_BASE + ASYNC_BANK3_SIZE;
+	icplb_bounds[i_i++].data = SDRAM_EBIU;
 	/* Addressing hole up to BootROM.  */
 	icplb_bounds[i_i].eaddr = BOOT_ROM_START;
 	icplb_bounds[i_i++].data = 0;
 	/* BootROM -- largest one should be less than 1 meg.  */
 	icplb_bounds[i_i].eaddr = BOOT_ROM_START + (1 * 1024 * 1024);
 	icplb_bounds[i_i++].data = SDRAM_IGENERIC;
+
 	if (L2_LENGTH) {
-		/* Addressing hole up to L2 SRAM, including the async bank.  */
+		/* Addressing hole up to L2 SRAM.  */
 		icplb_bounds[i_i].eaddr = L2_START;
 		icplb_bounds[i_i++].data = 0;
 		/* L2 SRAM.  */
-- 
1.6.4.2

[PATCH 67/72] Blackfin: increase default async timings for parallel flashes

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang@analog.com>

The default async timings are a little too fast for the parallel flash
that is attached by default to the async banks.  So slow things down a bit
so accessing the hardware is stable.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/configs/BF518F-EZBRD_defconfig |    4 ++--
 arch/blackfin/configs/BF526-EZBRD_defconfig  |    4 ++--
 arch/blackfin/configs/BF527-EZKIT_defconfig  |    4 ++--
 arch/blackfin/configs/BF548-EZKIT_defconfig  |    2 +-
 4 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/blackfin/configs/BF518F-EZBRD_defconfig b/arch/blackfin/configs/BF518F-EZBRD_defconfig
index dcfb488..9905b26 100644
--- a/arch/blackfin/configs/BF518F-EZBRD_defconfig
+++ b/arch/blackfin/configs/BF518F-EZBRD_defconfig
@@ -358,9 +358,9 @@ CONFIG_C_AMBEN_ALL=y
 # EBIU_AMBCTL Control
 #
 CONFIG_BANK_0=0x7BB0
-CONFIG_BANK_1=0x5554
+CONFIG_BANK_1=0x7BB0
 CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0xFFC0
+CONFIG_BANK_3=0x99B2
 
 #
 # Bus options (PCI, PCMCIA, EISA, MCA, ISA)
diff --git a/arch/blackfin/configs/BF526-EZBRD_defconfig b/arch/blackfin/configs/BF526-EZBRD_defconfig
index 48a3a7a..9dc6820 100644
--- a/arch/blackfin/configs/BF526-EZBRD_defconfig
+++ b/arch/blackfin/configs/BF526-EZBRD_defconfig
@@ -359,9 +359,9 @@ CONFIG_C_AMBEN_ALL=y
 # EBIU_AMBCTL Control
 #
 CONFIG_BANK_0=0x7BB0
-CONFIG_BANK_1=0x5554
+CONFIG_BANK_1=0x7BB0
 CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0xFFC0
+CONFIG_BANK_3=0x99B2
 
 #
 # Bus options (PCI, PCMCIA, EISA, MCA, ISA)
diff --git a/arch/blackfin/configs/BF527-EZKIT_defconfig b/arch/blackfin/configs/BF527-EZKIT_defconfig
index dd83527..77e35d4 100644
--- a/arch/blackfin/configs/BF527-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF527-EZKIT_defconfig
@@ -363,9 +363,9 @@ CONFIG_C_AMBEN_ALL=y
 # EBIU_AMBCTL Control
 #
 CONFIG_BANK_0=0x7BB0
-CONFIG_BANK_1=0x5554
+CONFIG_BANK_1=0x7BB0
 CONFIG_BANK_2=0x7BB0
-CONFIG_BANK_3=0xFFC0
+CONFIG_BANK_3=0x99B2
 
 #
 # Bus options (PCI, PCMCIA, EISA, MCA, ISA)
diff --git a/arch/blackfin/configs/BF548-EZKIT_defconfig b/arch/blackfin/configs/BF548-EZKIT_defconfig
index b3d3cab..f773ad1 100644
--- a/arch/blackfin/configs/BF548-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF548-EZKIT_defconfig
@@ -400,7 +400,7 @@ CONFIG_C_AMBEN_ALL=y
 # EBIU_AMBCTL Control
 #
 CONFIG_BANK_0=0x7BB0
-CONFIG_BANK_1=0x5554
+CONFIG_BANK_1=0x7BB0
 CONFIG_BANK_2=0x7BB0
 CONFIG_BANK_3=0x99B2
 CONFIG_EBIU_MBSCTLVAL=0x0
-- 
1.6.4.2

[PATCH 68/72] Blackfin: bf538-ezkit: add SPI IRQ resources

[Mike Frysinger]

From: Barry Song <barry.song@analog.com>

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf538/boards/ezkit.c |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/arch/blackfin/mach-bf538/boards/ezkit.c b/arch/blackfin/mach-bf538/boards/ezkit.c
index 9113f60..f2ac3b0 100644
--- a/arch/blackfin/mach-bf538/boards/ezkit.c
+++ b/arch/blackfin/mach-bf538/boards/ezkit.c
@@ -402,6 +402,11 @@ static struct resource bfin_spi2_resource[] = {
 	[1] = {
 		.start = CH_SPI2,
 		.end   = CH_SPI2,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI2,
+		.end   = IRQ_SPI2,
 		.flags = IORESOURCE_IRQ,
 	}
 };
-- 
1.6.4.2

[PATCH 69/72] Blackfin: cm-bf537u: split board from cm-bf537e

[Mike Frysinger]

From: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>

The cm-bf537u module, while similar to the cm-bf537e, is different enough
to warrant its own resources.  It has a USB controller but no PHY.

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig                       |    7 +-
 arch/blackfin/mach-bf537/boards/Kconfig     |   12 +-
 arch/blackfin/mach-bf537/boards/Makefile    |    3 +-
 arch/blackfin/mach-bf537/boards/cm_bf537.c  |  632 -----------------------
 arch/blackfin/mach-bf537/boards/cm_bf537e.c |  727 +++++++++++++++++++++++++++
 arch/blackfin/mach-bf537/boards/cm_bf537u.c |  633 +++++++++++++++++++++++
 6 files changed, 1375 insertions(+), 639 deletions(-)
 delete mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537.c
 create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537e.c
 create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537u.c

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index f20dc77..e7a781d 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -342,8 +342,9 @@ config MEM_MT48LC64M4A2FB_7E
 config MEM_MT48LC16M16A2TG_75
 	bool
 	depends on (BFIN533_EZKIT || BFIN561_EZKIT \
-		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
-		|| H8606_HVSISTEMAS || BFIN527_BLUETECHNIX_CM)
+		|| BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM_E \
+		|| BFIN537_BLUETECHNIX_CM_U || H8606_HVSISTEMAS \
+		|| BFIN527_BLUETECHNIX_CM)
 	default y
 
 config MEM_MT48LC32M8A2_75
@@ -459,7 +460,7 @@ config VCO_MULT
 	default "45" if BFIN533_STAMP
 	default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
 	default "22" if BFIN533_BLUETECHNIX_CM
-	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
+	default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
 	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
 	help
diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig
index 77c59da..44132fd 100644
--- a/arch/blackfin/mach-bf537/boards/Kconfig
+++ b/arch/blackfin/mach-bf537/boards/Kconfig
@@ -9,11 +9,17 @@ config BFIN537_STAMP
 	help
 	  BF537-STAMP board support.
 
-config BFIN537_BLUETECHNIX_CM
-	bool "Bluetechnix CM-BF537"
+config BFIN537_BLUETECHNIX_CM_E
+	bool "Bluetechnix CM-BF537E"
 	depends on (BF537)
 	help
-	  CM-BF537 support for EVAL- and DEV-Board.
+	  CM-BF537E support for EVAL- and DEV-Board.
+
+config BFIN537_BLUETECHNIX_CM_U
+	bool "Bluetechnix CM-BF537U"
+	depends on (BF537)
+	help
+	  CM-BF537U support for EVAL- and DEV-Board.
 
 config BFIN537_BLUETECHNIX_TCM
 	bool "Bluetechnix TCM-BF537"
diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile
index 68b98a7..7e6aa4e 100644
--- a/arch/blackfin/mach-bf537/boards/Makefile
+++ b/arch/blackfin/mach-bf537/boards/Makefile
@@ -3,7 +3,8 @@
 #
 
 obj-$(CONFIG_BFIN537_STAMP)            += stamp.o
-obj-$(CONFIG_BFIN537_BLUETECHNIX_CM)   += cm_bf537.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_E) += cm_bf537e.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_U) += cm_bf537u.o
 obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM)  += tcm_bf537.o
 obj-$(CONFIG_PNAV10)                   += pnav10.o
 obj-$(CONFIG_CAMSIG_MINOTAUR)          += minotaur.o
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
deleted file mode 100644
index 220cfda..0000000
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ /dev/null
@@ -1,632 +0,0 @@
-/*
- * File:         arch/blackfin/mach-bf537/boards/cm_bf537.c
- * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
- * Author:       Aidan Williams <aidan@nicta.com.au>
- *
- * Created:      2005
- * Description:  Board description file
- *
- * Modified:
- *               Copyright 2005 National ICT Australia (NICTA)
- *               Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-
-#include <linux/device.h>
-#include <linux/etherdevice.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
-#include <linux/ata_platform.h>
-#include <linux/irq.h>
-#include <asm/dma.h>
-#include <asm/bfin5xx_spi.h>
-#include <asm/portmux.h>
-#include <asm/dpmc.h>
-
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "Bluetechnix CM BF537";
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-/* all SPI peripherals info goes here */
-
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
-static struct mtd_partition bfin_spi_flash_partitions[] = {
-	{
-		.name = "bootloader(spi)",
-		.size = 0x00020000,
-		.offset = 0,
-		.mask_flags = MTD_CAP_ROM
-	}, {
-		.name = "linux kernel(spi)",
-		.size = 0xe0000,
-		.offset = 0x20000
-	}, {
-		.name = "file system(spi)",
-		.size = 0x700000,
-		.offset = 0x00100000,
-	}
-};
-
-static struct flash_platform_data bfin_spi_flash_data = {
-	.name = "m25p80",
-	.parts = bfin_spi_flash_partitions,
-	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
-	.type = "m25p64",
-};
-
-/* SPI flash chip (m25p64) */
-static struct bfin5xx_spi_chip spi_flash_chip_info = {
-	.enable_dma = 0,         /* use dma transfer with this chip*/
-	.bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-	.enable_dma = 1,         /* use dma transfer with this chip*/
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
-	.enable_dma = 0,
-	.bits_per_word = 8,
-};
-#endif
-
-static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
-	{
-		/* the modalias must be the same as spi device driver name */
-		.modalias = "m25p80", /* Name of spi_driver for this device */
-		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
-		.platform_data = &bfin_spi_flash_data,
-		.controller_data = &spi_flash_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-	{
-		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0, /* Framework bus number */
-		.chip_select = 1, /* Framework chip select. */
-		.platform_data = NULL, /* No spi_driver specific config */
-		.controller_data = &spi_adc_chip_info,
-	},
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-	{
-		.modalias = "ad1836",
-		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
-		.controller_data = &ad1836_spi_chip_info,
-	},
-#endif
-
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-	{
-		.modalias = "mmc_spi",
-		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
-		.bus_num = 0,
-		.chip_select = 1,
-		.controller_data = &mmc_spi_chip_info,
-		.mode = SPI_MODE_3,
-	},
-#endif
-};
-
-/* SPI (0) */
-static struct resource bfin_spi0_resource[] = {
-	[0] = {
-		.start = SPI0_REGBASE,
-		.end   = SPI0_REGBASE + 0xFF,
-		.flags = IORESOURCE_MEM,
-		},
-	[1] = {
-		.start = CH_SPI,
-		.end   = CH_SPI,
-		.flags = IORESOURCE_DMA,
-	},
-	[2] = {
-		.start = IRQ_SPI,
-		.end   = IRQ_SPI,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-/* SPI controller data */
-static struct bfin5xx_spi_master bfin_spi0_info = {
-	.num_chipselect = 8,
-	.enable_dma = 1,  /* master has the ability to do dma transfer */
-	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
-};
-
-static struct platform_device bfin_spi0_device = {
-	.name = "bfin-spi",
-	.id = 0, /* Bus number */
-	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
-	.resource = bfin_spi0_resource,
-	.dev = {
-		.platform_data = &bfin_spi0_info, /* Passed to driver */
-	},
-};
-#endif  /* spi master and devices */
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
-	.name = "rtc-bfin",
-	.id   = -1,
-};
-#endif
-
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
-static struct platform_device hitachi_fb_device = {
-	.name = "hitachi-tx09",
-};
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-#include <linux/smc91x.h>
-
-static struct smc91x_platdata smc91x_info = {
-	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
-	.leda = RPC_LED_100_10,
-	.ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
-	{
-		.start = 0x20200300,
-		.end = 0x20200300 + 16,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = IRQ_PF14,
-		.end = IRQ_PF14,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-		},
-};
-
-static struct platform_device smc91x_device = {
-	.name = "smc91x",
-	.id = 0,
-	.num_resources = ARRAY_SIZE(smc91x_resources),
-	.resource = smc91x_resources,
-	.dev	= {
-		.platform_data	= &smc91x_info,
-	},
-};
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
-	{
-		.start = 0x20308000,
-		.end = 0x20308000,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = 0x20308004,
-		.end = 0x20308004,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = IRQ_PG15,
-		.end = IRQ_PG15,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-static struct isp1362_platform_data isp1362_priv = {
-	.sel15Kres = 1,
-	.clknotstop = 0,
-	.oc_enable = 0,
-	.int_act_high = 0,
-	.int_edge_triggered = 0,
-	.remote_wakeup_connected = 0,
-	.no_power_switching = 1,
-	.power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
-	.name = "isp1362-hcd",
-	.id = 0,
-	.dev = {
-		.platform_data = &isp1362_priv,
-	},
-	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
-	.resource = isp1362_hcd_resources,
-};
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-static struct resource net2272_bfin_resources[] = {
-	{
-		.start = 0x20200000,
-		.end = 0x20200000 + 0x100,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = IRQ_PH14,
-		.end = IRQ_PH14,
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-	},
-};
-
-static struct platform_device net2272_bfin_device = {
-	.name = "net2272",
-	.id = -1,
-	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
-	.resource = net2272_bfin_resources,
-};
-#endif
-
-static struct resource bfin_gpios_resources = {
-	.start = 0,
-	.end   = MAX_BLACKFIN_GPIOS - 1,
-	.flags = IORESOURCE_IRQ,
-};
-
-static struct platform_device bfin_gpios_device = {
-	.name = "simple-gpio",
-	.id = -1,
-	.num_resources = 1,
-	.resource = &bfin_gpios_resources,
-};
-
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
-static struct mtd_partition cm_partitions[] = {
-	{
-		.name   = "bootloader(nor)",
-		.size   = 0x40000,
-		.offset = 0,
-	}, {
-		.name   = "linux kernel(nor)",
-		.size   = 0xE0000,
-		.offset = MTDPART_OFS_APPEND,
-	}, {
-		.name   = "file system(nor)",
-		.size   = MTDPART_SIZ_FULL,
-		.offset = MTDPART_OFS_APPEND,
-	}
-};
-
-static struct physmap_flash_data cm_flash_data = {
-	.width    = 2,
-	.parts    = cm_partitions,
-	.nr_parts = ARRAY_SIZE(cm_partitions),
-};
-
-static unsigned cm_flash_gpios[] = { GPIO_PF4 };
-
-static struct resource cm_flash_resource[] = {
-	{
-		.name  = "cfi_probe",
-		.start = 0x20000000,
-		.end   = 0x201fffff,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = (unsigned long)cm_flash_gpios,
-		.end   = ARRAY_SIZE(cm_flash_gpios),
-		.flags = IORESOURCE_IRQ,
-	}
-};
-
-static struct platform_device cm_flash_device = {
-	.name          = "gpio-addr-flash",
-	.id            = 0,
-	.dev = {
-		.platform_data = &cm_flash_data,
-	},
-	.num_resources = ARRAY_SIZE(cm_flash_resource),
-	.resource      = cm_flash_resource,
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
-	{
-		.start = 0xFFC00400,
-		.end = 0xFFC004FF,
-		.flags = IORESOURCE_MEM,
-	}, {
-		.start = 0xFFC02000,
-		.end = 0xFFC020FF,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device bfin_uart_device = {
-	.name = "bfin-uart",
-	.id = 1,
-	.num_resources = ARRAY_SIZE(bfin_uart_resources),
-	.resource = bfin_uart_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
-	{
-		.start = 0xFFC00400,
-		.end = 0xFFC004FF,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = IRQ_UART0_RX,
-		.end = IRQ_UART0_RX+1,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.start = CH_UART0_RX,
-		.end = CH_UART0_RX+1,
-		.flags = IORESOURCE_DMA,
-	},
-};
-static struct platform_device bfin_sir0_device = {
-	.name = "bfin_sir",
-	.id = 0,
-	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
-	.resource = bfin_sir0_resources,
-};
-#endif
-#ifdef CONFIG_BFIN_SIR1
-static struct resource bfin_sir1_resources[] = {
-	{
-		.start = 0xFFC02000,
-		.end = 0xFFC020FF,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = IRQ_UART1_RX,
-		.end = IRQ_UART1_RX+1,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.start = CH_UART1_RX,
-		.end = CH_UART1_RX+1,
-		.flags = IORESOURCE_DMA,
-	},
-};
-static struct platform_device bfin_sir1_device = {
-	.name = "bfin_sir",
-	.id = 1,
-	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
-	.resource = bfin_sir1_resources,
-};
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-static struct resource bfin_twi0_resource[] = {
-	[0] = {
-		.start = TWI0_REGBASE,
-		.end   = TWI0_REGBASE,
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = IRQ_TWI,
-		.end   = IRQ_TWI,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device i2c_bfin_twi_device = {
-	.name = "i2c-bfin-twi",
-	.id = 0,
-	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
-	.resource = bfin_twi0_resource,
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-static struct platform_device bfin_sport0_uart_device = {
-	.name = "bfin-sport-uart",
-	.id = 0,
-};
-
-static struct platform_device bfin_sport1_uart_device = {
-	.name = "bfin-sport-uart",
-	.id = 1,
-};
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-static struct platform_device bfin_mii_bus = {
-	.name = "bfin_mii_bus",
-};
-
-static struct platform_device bfin_mac_device = {
-	.name = "bfin_mac",
-	.dev.platform_data = &bfin_mii_bus,
-};
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-#define PATA_INT	IRQ_PF14
-
-static struct pata_platform_info bfin_pata_platform_data = {
-	.ioport_shift = 2,
-	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
-};
-
-static struct resource bfin_pata_resources[] = {
-	{
-		.start = 0x2030C000,
-		.end = 0x2030C01F,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = 0x2030D018,
-		.end = 0x2030D01B,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = PATA_INT,
-		.end = PATA_INT,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device bfin_pata_device = {
-	.name = "pata_platform",
-	.id = -1,
-	.num_resources = ARRAY_SIZE(bfin_pata_resources),
-	.resource = bfin_pata_resources,
-	.dev = {
-		.platform_data = &bfin_pata_platform_data,
-	}
-};
-#endif
-
-static const unsigned int cclk_vlev_datasheet[] =
-{
-	VRPAIR(VLEV_085, 250000000),
-	VRPAIR(VLEV_090, 376000000),
-	VRPAIR(VLEV_095, 426000000),
-	VRPAIR(VLEV_100, 426000000),
-	VRPAIR(VLEV_105, 476000000),
-	VRPAIR(VLEV_110, 476000000),
-	VRPAIR(VLEV_115, 476000000),
-	VRPAIR(VLEV_120, 500000000),
-	VRPAIR(VLEV_125, 533000000),
-	VRPAIR(VLEV_130, 600000000),
-};
-
-static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
-	.tuple_tab = cclk_vlev_datasheet,
-	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
-	.vr_settling_time = 25 /* us */,
-};
-
-static struct platform_device bfin_dpmc = {
-	.name = "bfin dpmc",
-	.dev = {
-		.platform_data = &bfin_dmpc_vreg_data,
-	},
-};
-
-static struct platform_device *cm_bf537_devices[] __initdata = {
-
-	&bfin_dpmc,
-
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
-	&hitachi_fb_device,
-#endif
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-	&rtc_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-	&bfin_uart_device,
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-	&bfin_sir0_device,
-#endif
-#ifdef CONFIG_BFIN_SIR1
-	&bfin_sir1_device,
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-	&i2c_bfin_twi_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-	&bfin_sport0_uart_device,
-	&bfin_sport1_uart_device,
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-	&isp1362_hcd_device,
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-	&smc91x_device,
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-	&bfin_mii_bus,
-	&bfin_mac_device,
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-	&net2272_bfin_device,
-#endif
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-	&bfin_spi0_device,
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-	&bfin_pata_device,
-#endif
-
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
-	&cm_flash_device,
-#endif
-
-	&bfin_gpios_device,
-};
-
-static int __init cm_bf537_init(void)
-{
-	printk(KERN_INFO "%s(): registering device resources\n", __func__);
-	platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
-#endif
-	return 0;
-}
-
-arch_initcall(cm_bf537_init);
-
-void bfin_get_ether_addr(char *addr)
-{
-	random_ether_addr(addr);
-	printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
-}
-EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537e.c b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
new file mode 100644
index 0000000..87acb7d
--- /dev/null
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
@@ -0,0 +1,727 @@
+/*
+ * File:         arch/blackfin/mach-bf537/boards/cm_bf537.c
+ * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:      2005
+ * Description:  Board description file
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <linux/ata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM BF537E";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00020000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = 0xe0000,
+		.offset = 0x20000
+	}, {
+		.name = "file system(spi)",
+		.size = 0x700000,
+		.offset = 0x00100000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+static struct platform_device hitachi_fb_device = {
+	.name = "hitachi-tx09",
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91x_resources[] = {
+	{
+		.start = 0x20200300,
+		.end = 0x20200300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF14,
+		.end = IRQ_PF14,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		},
+};
+
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20308000,
+		.end = 0x20308000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20308004,
+		.end = 0x20308004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PG15,
+		.end = IRQ_PG15,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PG13,
+		.end = IRQ_PG13,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+	.start = 0,
+	.end   = MAX_BLACKFIN_GPIOS - 1,
+	.flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+	.name = "simple-gpio",
+	.id = -1,
+	.num_resources = 1,
+	.resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+	{
+		.name   = "bootloader(nor)",
+		.size   = 0x40000,
+		.offset = 0,
+	}, {
+		.name   = "linux kernel(nor)",
+		.size   = 0x100000,
+		.offset = MTDPART_OFS_APPEND,
+	}, {
+		.name   = "file system(nor)",
+		.size   = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data cm_flash_data = {
+	.width    = 2,
+	.parts    = cm_partitions,
+	.nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PF4 };
+
+static struct resource cm_flash_resource[] = {
+	{
+		.name  = "cfi_probe",
+		.start = 0x20000000,
+		.end   = 0x201fffff,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = (unsigned long)cm_flash_gpios,
+		.end   = ARRAY_SIZE(cm_flash_gpios),
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device cm_flash_device = {
+	.name          = "gpio-addr-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &cm_flash_data,
+	},
+	.num_resources = ARRAY_SIZE(cm_flash_resource),
+	.resource      = cm_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART0_ERROR,
+		.end = IRQ_UART0_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_TX,
+		.end = CH_UART0_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart0_device = {
+	.name = "bfin-uart",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
+	.resource = bfin_uart0_resources,
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = IRQ_UART1_ERROR,
+		.end = IRQ_UART1_ERROR,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_TX,
+		.end = CH_UART1_TX,
+		.flags = IORESOURCE_DMA,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX,
+		.flags = IORESOURCE_DMA,
+	},
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+	{
+		/*
+		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+		 */
+		.start = -1,
+		.end = -1,
+		.flags = IORESOURCE_IO,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart1_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
+	.resource = bfin_uart1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir0_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
+	.resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir1_device = {
+	.name = "bfin_sir",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
+	.resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+	.name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+	.dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT	IRQ_PF14
+
+static struct pata_platform_info bfin_pata_platform_data = {
+	.ioport_shift = 2,
+	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+	{
+		.start = 0x2030C000,
+		.end = 0x2030C01F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = 0x2030D018,
+		.end = 0x2030D01B,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = PATA_INT,
+		.end = PATA_INT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pata_device = {
+	.name = "pata_platform",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pata_resources),
+	.resource = bfin_pata_resources,
+	.dev = {
+		.platform_data = &bfin_pata_platform_data,
+	}
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+	VRPAIR(VLEV_085, 250000000),
+	VRPAIR(VLEV_090, 376000000),
+	VRPAIR(VLEV_095, 426000000),
+	VRPAIR(VLEV_100, 426000000),
+	VRPAIR(VLEV_105, 476000000),
+	VRPAIR(VLEV_110, 476000000),
+	VRPAIR(VLEV_115, 476000000),
+	VRPAIR(VLEV_120, 500000000),
+	VRPAIR(VLEV_125, 533000000),
+	VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *cm_bf537e_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+	&hitachi_fb_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	&bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	&bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+	&bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	&bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mii_bus,
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	&bfin_pata_device,
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+	&cm_flash_device,
+#endif
+
+	&bfin_gpios_device,
+};
+
+static int __init cm_bf537e_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+	return 0;
+}
+
+arch_initcall(cm_bf537e_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+	random_ether_addr(addr);
+	printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537u.c b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
new file mode 100644
index 0000000..8219dc3
--- /dev/null
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
@@ -0,0 +1,633 @@
+/*
+ * File:         arch/blackfin/mach-bf537/boards/cm_bf537u.c
+ * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:      2005
+ * Description:  Board description file
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <linux/ata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+#include <linux/spi/mmc_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM BF537U";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00020000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = 0xe0000,
+		.offset = 0x20000
+	}, {
+		.name = "file system(spi)",
+		.size = 0x700000,
+		.offset = 0x00100000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+	{
+		.modalias = "mmc_spi",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &mmc_spi_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_DMA,
+	},
+	[2] = {
+		.start = IRQ_SPI,
+		.end   = IRQ_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+static struct platform_device hitachi_fb_device = {
+	.name = "hitachi-tx09",
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+	.leda = RPC_LED_100_10,
+	.ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91x_resources[] = {
+	{
+		.start = 0x20200300,
+		.end = 0x20200300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF14,
+		.end = IRQ_PF14,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+		},
+};
+
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20308000,
+		.end = 0x20308000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20308004,
+		.end = 0x20308004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PG15,
+		.end = IRQ_PG15,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20200000,
+		.end = 0x20200000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PH14,
+		.end = IRQ_PH14,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+	.start = 0,
+	.end   = MAX_BLACKFIN_GPIOS - 1,
+	.flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+	.name = "simple-gpio",
+	.id = -1,
+	.num_resources = 1,
+	.resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+	{
+		.name   = "bootloader(nor)",
+		.size   = 0x40000,
+		.offset = 0,
+	}, {
+		.name   = "linux kernel(nor)",
+		.size   = 0x100000,
+		.offset = MTDPART_OFS_APPEND,
+	}, {
+		.name   = "file system(nor)",
+		.size   = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data cm_flash_data = {
+	.width    = 2,
+	.parts    = cm_partitions,
+	.nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PH0 };
+
+static struct resource cm_flash_resource[] = {
+	{
+		.name  = "cfi_probe",
+		.start = 0x20000000,
+		.end   = 0x201fffff,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = (unsigned long)cm_flash_gpios,
+		.end   = ARRAY_SIZE(cm_flash_gpios),
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device cm_flash_device = {
+	.name          = "gpio-addr-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &cm_flash_data,
+	},
+	.num_resources = ARRAY_SIZE(cm_flash_resource),
+	.resource      = cm_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART0_RX,
+		.end = IRQ_UART0_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART0_RX,
+		.end = CH_UART0_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir0_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
+	.resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_UART1_RX,
+		.end = IRQ_UART1_RX+1,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.start = CH_UART1_RX,
+		.end = CH_UART1_RX+1,
+		.flags = IORESOURCE_DMA,
+	},
+};
+static struct platform_device bfin_sir1_device = {
+	.name = "bfin_sir",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
+	.resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+	.name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+	.dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT	IRQ_PF14
+
+static struct pata_platform_info bfin_pata_platform_data = {
+	.ioport_shift = 2,
+	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+	{
+		.start = 0x2030C000,
+		.end = 0x2030C01F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = 0x2030D018,
+		.end = 0x2030D01B,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = PATA_INT,
+		.end = PATA_INT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pata_device = {
+	.name = "pata_platform",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pata_resources),
+	.resource = bfin_pata_resources,
+	.dev = {
+		.platform_data = &bfin_pata_platform_data,
+	}
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+	VRPAIR(VLEV_085, 250000000),
+	VRPAIR(VLEV_090, 376000000),
+	VRPAIR(VLEV_095, 426000000),
+	VRPAIR(VLEV_100, 426000000),
+	VRPAIR(VLEV_105, 476000000),
+	VRPAIR(VLEV_110, 476000000),
+	VRPAIR(VLEV_115, 476000000),
+	VRPAIR(VLEV_120, 500000000),
+	VRPAIR(VLEV_125, 533000000),
+	VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *cm_bf537u_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+	&hitachi_fb_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+	&bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	&bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mii_bus,
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	&bfin_pata_device,
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+	&cm_flash_device,
+#endif
+
+	&bfin_gpios_device,
+};
+
+static int __init cm_bf537u_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+	platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+	return 0;
+}
+
+arch_initcall(cm_bf537u_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+	random_ether_addr(addr);
+	printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
-- 
1.6.4.2

[PATCH 70/72] Blackfin: update cm board resources

[Mike Frysinger]

From: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/mach-bf527/boards/cm_bf527.c  |   97 ++++++++++++----------
 arch/blackfin/mach-bf533/boards/cm_bf533.c  |  114 ++++++++++++++++++++++++++-
 arch/blackfin/mach-bf537/boards/tcm_bf537.c |   13 ++--
 arch/blackfin/mach-bf548/boards/cm_bf548.c  |   15 +++-
 arch/blackfin/mach-bf561/boards/cm_bf561.c  |  113 ++++++++++++++++++++++++++-
 5 files changed, 297 insertions(+), 55 deletions(-)

diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index a0f623d..08a3f01 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -151,46 +151,6 @@ static struct platform_device musb_device = {
 };
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
-static struct mtd_partition ezkit_partitions[] = {
-	{
-		.name       = "bootloader(nor)",
-		.size       = 0x40000,
-		.offset     = 0,
-	}, {
-		.name       = "linux kernel(nor)",
-		.size       = 0x1C0000,
-		.offset     = MTDPART_OFS_APPEND,
-	}, {
-		.name       = "file system(nor)",
-		.size       = MTDPART_SIZ_FULL,
-		.offset     = MTDPART_OFS_APPEND,
-	}
-};
-
-static struct physmap_flash_data ezkit_flash_data = {
-	.width      = 2,
-	.parts      = ezkit_partitions,
-	.nr_parts   = ARRAY_SIZE(ezkit_partitions),
-};
-
-static struct resource ezkit_flash_resource = {
-	.start = 0x20000000,
-	.end   = 0x201fffff,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device ezkit_flash_device = {
-	.name          = "physmap-flash",
-	.id            = 0,
-	.dev = {
-		.platform_data = &ezkit_flash_data,
-	},
-	.num_resources = 1,
-	.resource      = &ezkit_flash_resource,
-};
-#endif
-
 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 static struct mtd_partition partition_info[] = {
 	{
@@ -662,6 +622,55 @@ static struct platform_device bfin_fb_adv7393_device = {
 };
 #endif
 
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+	{
+		.name   = "bootloader(nor)",
+		.size   = 0x40000,
+		.offset = 0,
+	}, {
+		.name   = "linux kernel(nor)",
+		.size   = 0x100000,
+		.offset = MTDPART_OFS_APPEND,
+	}, {
+		.name   = "file system(nor)",
+		.size   = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data cm_flash_data = {
+	.width    = 2,
+	.parts    = cm_partitions,
+	.nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PH9, GPIO_PG11 };
+
+static struct resource cm_flash_resource[] = {
+	{
+		.name  = "cfi_probe",
+		.start = 0x20000000,
+		.end   = 0x201fffff,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = (unsigned long)cm_flash_gpios,
+		.end   = ARRAY_SIZE(cm_flash_gpios),
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device cm_flash_device = {
+	.name          = "gpio-addr-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &cm_flash_data,
+	},
+	.num_resources = ARRAY_SIZE(cm_flash_resource),
+	.resource      = cm_flash_resource,
+};
+#endif
+
 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 static struct resource bfin_uart_resources[] = {
 #ifdef CONFIG_SERIAL_BFIN_UART0
@@ -847,7 +856,7 @@ static struct platform_device bfin_dpmc = {
 	},
 };
 
-static struct platform_device *stamp_devices[] __initdata = {
+static struct platform_device *cmbf527_devices[] __initdata = {
 
 	&bfin_dpmc,
 
@@ -930,8 +939,8 @@ static struct platform_device *stamp_devices[] __initdata = {
 	&bfin_device_gpiokeys,
 #endif
 
-#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
-	&ezkit_flash_device,
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+	&cm_flash_device,
 #endif
 
 	&bfin_gpios_device,
@@ -942,7 +951,7 @@ static int __init cm_init(void)
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	i2c_register_board_info(0, bfin_i2c_board_info,
 				ARRAY_SIZE(bfin_i2c_board_info));
-	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+	platform_add_devices(cmbf527_devices, ARRAY_SIZE(cmbf527_devices));
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 	return 0;
 }
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index ef31bc5..7443b26 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -31,8 +31,10 @@
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
+#include <linux/spi/mmc_spi.h>
 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 #include <linux/usb/isp1362.h>
 #endif
@@ -141,9 +143,9 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
-		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 5,
+		.chip_select = 1,
 		.controller_data = &mmc_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
@@ -225,6 +227,40 @@ static struct platform_device smc91x_device = {
 };
 #endif
 
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
+static struct resource smsc911x_resources[] = {
+	{
+		.name = "smsc911x-memory",
+		.start = 0x20308000,
+		.end = 0x20308000 + 0xFF,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF8,
+		.end = IRQ_PF8,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	},
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+	.flags = SMSC911X_USE_16BIT,
+	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+	.name = "smsc911x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smsc911x_resources),
+	.resource = smsc911x_resources,
+	.dev = {
+		.platform_data = &smsc911x_config,
+	},
+};
+#endif
+
 static struct resource bfin_gpios_resources = {
 	.start = 0,
 	.end   = MAX_BLACKFIN_GPIOS - 1,
@@ -335,6 +371,68 @@ static struct platform_device isp1362_hcd_device = {
 };
 #endif
 
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF6,
+		.end = IRQ_PF6,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+
+
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition para_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0x40000,
+		.offset     = 0,
+	}, {
+		.name       = "linux+rootfs(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	},
+};
+
+static struct physmap_flash_data para_flash_data = {
+	.width      = 2,
+	.parts      = para_partitions,
+	.nr_parts   = ARRAY_SIZE(para_partitions),
+};
+
+static struct resource para_flash_resource = {
+	.start = 0x20000000,
+	.end   = 0x201fffff,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device para_flash_device = {
+	.name          = "physmap-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &para_flash_data,
+	},
+	.num_resources = 1,
+	.resource      = &para_flash_resource,
+};
+#endif
+
+
+
 static const unsigned int cclk_vlev_datasheet[] =
 {
 	VRPAIR(VLEV_085, 250000000),
@@ -393,10 +491,22 @@ static struct platform_device *cm_bf533_devices[] __initdata = {
 	&smc91x_device,
 #endif
 
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+	&smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 	&bfin_spi0_device,
 #endif
 
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&para_flash_device,
+#endif
+
 	&bfin_gpios_device,
 };
 
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index dc4f161..61353f7 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -45,6 +45,7 @@
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
+#include <linux/spi/mmc_spi.h>
 
 /*
  * Name the Board for the /proc/cpuinfo
@@ -148,7 +149,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 		.modalias = "mmc_spi",
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 5,
+		.chip_select = 1,
 		.controller_data = &mmc_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
@@ -279,12 +280,12 @@ static struct platform_device isp1362_hcd_device = {
 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 static struct resource net2272_bfin_resources[] = {
 	{
-		.start = 0x20200000,
-		.end = 0x20200000 + 0x100,
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
 	}, {
-		.start = IRQ_PH14,
-		.end = IRQ_PH14,
+		.start = IRQ_PG13,
+		.end = IRQ_PG13,
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 	},
 };
@@ -318,7 +319,7 @@ static struct mtd_partition cm_partitions[] = {
 		.offset = 0,
 	}, {
 		.name   = "linux kernel(nor)",
-		.size   = 0xE0000,
+		.size   = 0x100000,
 		.offset = MTDPART_OFS_APPEND,
 	}, {
 		.name   = "file system(nor)",
diff --git a/arch/blackfin/mach-bf548/boards/cm_bf548.c b/arch/blackfin/mach-bf548/boards/cm_bf548.c
index 290b6e9..e565aae 100644
--- a/arch/blackfin/mach-bf548/boards/cm_bf548.c
+++ b/arch/blackfin/mach-bf548/boards/cm_bf548.c
@@ -291,6 +291,8 @@ static struct platform_device bfin_sir3_device = {
 #endif
 
 #if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
 static struct resource smsc911x_resources[] = {
 	{
 		.name = "smsc911x-memory",
@@ -304,11 +306,22 @@ static struct resource smsc911x_resources[] = {
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 	},
 };
+
+static struct smsc911x_platform_config smsc911x_config = {
+	.flags = SMSC911X_USE_16BIT,
+	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
 static struct platform_device smsc911x_device = {
 	.name = "smsc911x",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smsc911x_resources),
 	.resource = smsc911x_resources,
+	.dev = {
+		.platform_data = &smsc911x_config,
+	},
 };
 #endif
 
@@ -473,7 +486,7 @@ static struct mtd_partition para_partitions[] = {
 		.offset     = 0,
 	}, {
 		.name       = "linux kernel(nor)",
-		.size       = 0x400000,
+		.size       = 0x100000,
 		.offset     = MTDPART_OFS_APPEND,
 	}, {
 		.name       = "file system(nor)",
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 5721620..6577ecf 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -42,6 +42,7 @@
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
+#include <linux/mtd/physmap.h>
 
 /*
  * Name the Board for the /proc/cpuinfo
@@ -142,9 +143,9 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 	{
 		.modalias = "mmc_spi",
-		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
-		.chip_select = 5,
+		.chip_select = 1,
 		.controller_data = &mmc_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
@@ -228,6 +229,62 @@ static struct platform_device smc91x_device = {
 };
 #endif
 
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
+static struct resource smsc911x_resources[] = {
+	{
+		.name = "smsc911x-memory",
+		.start = 0x24008000,
+		.end = 0x24008000 + 0xFF,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = IRQ_PF43,
+		.end = IRQ_PF43,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	},
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+	.flags = SMSC911X_USE_16BIT,
+	.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+	.name = "smsc911x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smsc911x_resources),
+	.resource = smsc911x_resources,
+	.dev = {
+		.platform_data = &smsc911x_config,
+	},
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x24000000,
+		.end = 0x24000000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF45,
+		.end = IRQ_PF45,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
 static struct resource bfin_gpios_resources = {
 	.start = 0,
 	.end   = MAX_BLACKFIN_GPIOS - 1,
@@ -363,6 +420,46 @@ static struct platform_device bfin_pata_device = {
 };
 #endif
 
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+static struct mtd_partition para_partitions[] = {
+	{
+		.name       = "bootloader(nor)",
+		.size       = 0x40000,
+		.offset     = 0,
+	}, {
+		.name       = "linux kernel(nor)",
+		.size       = 0x100000,
+		.offset     = MTDPART_OFS_APPEND,
+	}, {
+		.name       = "file system(nor)",
+		.size       = MTDPART_SIZ_FULL,
+		.offset     = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct physmap_flash_data para_flash_data = {
+	.width      = 2,
+	.parts      = para_partitions,
+	.nr_parts   = ARRAY_SIZE(para_partitions),
+};
+
+static struct resource para_flash_resource = {
+	.start = 0x20000000,
+	.end   = 0x207fffff,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device para_flash_device = {
+	.name          = "physmap-flash",
+	.id            = 0,
+	.dev = {
+		.platform_data = &para_flash_data,
+	},
+	.num_resources = 1,
+	.resource      = &para_flash_resource,
+};
+#endif
+
 static const unsigned int cclk_vlev_datasheet[] =
 {
 	VRPAIR(VLEV_085, 250000000),
@@ -416,6 +513,14 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
 	&smc91x_device,
 #endif
 
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+	&smsc911x_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 	&bfin_spi0_device,
 #endif
@@ -424,6 +529,10 @@ static struct platform_device *cm_bf561_devices[] __initdata = {
 	&bfin_pata_device,
 #endif
 
+#if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
+	&para_flash_device,
+#endif
+
 	&bfin_gpios_device,
 };
 
-- 
1.6.4.2

[PATCH 71/72] Blackfin: update ftrace_push_return_trace() breakage

[Mike Frysinger]

Commit 71e308a239c updated ftrace_push_return_trace() prototype but didn't
update the Blackfin ftrace code, so things broke.  Since we don't support
the new stuff yet, call it with stub values.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/kernel/ftrace.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/blackfin/kernel/ftrace.c b/arch/blackfin/kernel/ftrace.c
index 905bfc4..f2c85ac 100644
--- a/arch/blackfin/kernel/ftrace.c
+++ b/arch/blackfin/kernel/ftrace.c
@@ -24,7 +24,7 @@ void prepare_ftrace_return(unsigned long *parent, unsigned long self_addr)
 	if (unlikely(atomic_read(&current->tracing_graph_pause)))
 		return;
 
-	if (ftrace_push_return_trace(*parent, self_addr, &trace.depth) == -EBUSY)
+	if (ftrace_push_return_trace(*parent, self_addr, &trace.depth, 0) == -EBUSY)
 		return;
 
 	trace.func = self_addr;
-- 
1.6.4.2

[PATCH 72/72] Blackfin: swap clocksource ratings for gptimer/cycles

[Mike Frysinger]

From: Graf Yang <graf.yang@analog.com>

The cycles clocksource is a higher resolution than the gptimer one, so
make sure the ratings field reflects this.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 arch/blackfin/Kconfig          |    2 +-
 arch/blackfin/kernel/time-ts.c |    4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index e7a781d..9a01d44 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -648,7 +648,7 @@ config CYCLES_CLOCKSOURCE
 	  writing the registers will most likely crash the kernel.
 
 config GPTMR0_CLOCKSOURCE
-	bool "Use GPTimer0 as a clocksource (higher rating)"
+	bool "Use GPTimer0 as a clocksource"
 	select BFIN_GPTIMERS
 	depends on GENERIC_CLOCKEVENTS
 	depends on !TICKSOURCE_GPTMR0
diff --git a/arch/blackfin/kernel/time-ts.c b/arch/blackfin/kernel/time-ts.c
index 0791eba..f971576 100644
--- a/arch/blackfin/kernel/time-ts.c
+++ b/arch/blackfin/kernel/time-ts.c
@@ -66,7 +66,7 @@ static cycle_t bfin_read_cycles(struct clocksource *cs)
 
 static struct clocksource bfin_cs_cycles = {
 	.name		= "bfin_cs_cycles",
-	.rating		= 350,
+	.rating		= 400,
 	.read		= bfin_read_cycles,
 	.mask		= CLOCKSOURCE_MASK(64),
 	.shift		= 22,
@@ -115,7 +115,7 @@ static cycle_t bfin_read_gptimer0(void)
 
 static struct clocksource bfin_cs_gptimer0 = {
 	.name		= "bfin_cs_gptimer0",
-	.rating		= 400,
+	.rating		= 350,
 	.read		= bfin_read_gptimer0,
 	.mask		= CLOCKSOURCE_MASK(32),
 	.shift		= 22,
-- 
1.6.4.2

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
> Minor highlights:
>  - shadow console to help with really early kernel output
>  - proper decoding of double fault handling
> 
> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
> 

Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
several errors..  Could you clean those up those errors before sending
this up stream?

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Mon, Sep 14, 2009 at 16:50, Daniel Walker wrote:
> On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
>> Minor highlights:
>>  - shadow console to help with really early kernel output
>>  - proper decoding of double fault handling
>>
>> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
>>
>
> Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
> several errors..  Could you clean those up those errors before sending
> this up stream?

i already checked/reviewed the output in the series
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Mon, 2009-09-14 at 16:57 -0400, Mike Frysinger wrote:
> On Mon, Sep 14, 2009 at 16:50, Daniel Walker wrote:
> > On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
> >> Minor highlights:
> >>  - shadow console to help with really early kernel output
> >>  - proper decoding of double fault handling
> >>
> >> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
> >>
> >
> > Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
> > several errors..  Could you clean those up those errors before sending
> > this up stream?
> 
> i already checked/reviewed the output in the series

The remaining problems can be fixed .. Why did you leave those errors ?

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Mon, Sep 14, 2009 at 17:04, Daniel Walker wrote:
> On Mon, 2009-09-14 at 16:57 -0400, Mike Frysinger wrote:
>> On Mon, Sep 14, 2009 at 16:50, Daniel Walker wrote:
>> > On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
>> >> Minor highlights:
>> >>  - shadow console to help with really early kernel output
>> >>  - proper decoding of double fault handling
>> >>
>> >> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
>> >>
>> >
>> > Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
>> > several errors..  Could you clean those up those errors before sending
>> > this up stream?
>>
>> i already checked/reviewed the output in the series
>
> The remaining problems can be fixed .. Why did you leave those errors ?

i'm not going to sweat 80 col warnings when the line is 81 cols with
tabs of 8 spaces

as for the other errors, you probably didnt read the code.  you saw
"error" and assumed checkpatch was correct.  it isnt always as it isnt
a C parser.
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Mon, 2009-09-14 at 17:07 -0400, Mike Frysinger wrote:
> On Mon, Sep 14, 2009 at 17:04, Daniel Walker wrote:
> > On Mon, 2009-09-14 at 16:57 -0400, Mike Frysinger wrote:
> >> On Mon, Sep 14, 2009 at 16:50, Daniel Walker wrote:
> >> > On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
> >> >> Minor highlights:
> >> >>  - shadow console to help with really early kernel output
> >> >>  - proper decoding of double fault handling
> >> >>
> >> >> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
> >> >>
> >> >
> >> > Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
> >> > several errors..  Could you clean those up those errors before sending
> >> > this up stream?
> >>
> >> i already checked/reviewed the output in the series
> >
> > The remaining problems can be fixed .. Why did you leave those errors ?
> 
> i'm not going to sweat 80 col warnings when the line is 81 cols with
> tabs of 8 spaces

The line length ones I'm not worried about, those are just warnings..

> as for the other errors, you probably didnt read the code.  you saw
> "error" and assumed checkpatch was correct.  it isnt always as it isnt
> a C parser.

Checkpatch is finding real issues with your patches.. You have
indentations issues in several of the patches. Your removing good
formatting and replacing it improper formatting. For instance,

ERROR: code indent should use tabs where possible
#115: FILE: arch/blackfin/kernel/module.c:102:
+^I^I           (!strcmp(".bss", shname) &&$

The line your removing had the proper formatting, but this new line has
improper formatting.. You have several of these issues, you must think
they aren't important but checkpatch has the WARNING and ERROR
classification for a reason .. The errors are actual style violation
that really need to be either cleaned up or explained..

They can be trivially fixed, it's just a matter of adding the proper
indentation ..

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Mon, Sep 14, 2009 at 17:21, Daniel Walker wrote:
> On Mon, 2009-09-14 at 17:07 -0400, Mike Frysinger wrote:
>> On Mon, Sep 14, 2009 at 17:04, Daniel Walker wrote:
>> > On Mon, 2009-09-14 at 16:57 -0400, Mike Frysinger wrote:
>> >> On Mon, Sep 14, 2009 at 16:50, Daniel Walker wrote:
>> >> > On Mon, 2009-09-14 at 16:07 -0400, Mike Frysinger wrote:
>> >> >> Minor highlights:
>> >> >>  - shadow console to help with really early kernel output
>> >> >>  - proper decoding of double fault handling
>> >> >>
>> >> >> Otherwise, we've got the normal bug fixes, IPIPE updates, and clean ups.
>> >> >>
>> >> >
>> >> > Patches 15, 16, 20, 21, and 61 all have checkpatch errors some with
>> >> > several errors..  Could you clean those up those errors before sending
>> >> > this up stream?
>> >>
>> >> i already checked/reviewed the output in the series
>> >
>> > The remaining problems can be fixed .. Why did you leave those errors ?
>>
>> i'm not going to sweat 80 col warnings when the line is 81 cols with
>> tabs of 8 spaces
>
> The line length ones I'm not worried about, those are just warnings..
>
>> as for the other errors, you probably didnt read the code.  you saw
>> "error" and assumed checkpatch was correct.  it isnt always as it isnt
>> a C parser.
>
> Checkpatch is finding real issues with your patches.. You have
> indentations issues in several of the patches. Your removing good
> formatting and replacing it improper formatting. For instance,
>
> ERROR: code indent should use tabs where possible
> #115: FILE: arch/blackfin/kernel/module.c:102:
> +^I^I           (!strcmp(".bss", shname) &&$
>
> The line your removing had the proper formatting, but this new line has
> improper formatting.. You have several of these issues, you must think
> they aren't important but checkpatch has the WARNING and ERROR
> classification for a reason .. The errors are actual style violation
> that really need to be either cleaned up or explained..
>
> They can be trivially fixed, it's just a matter of adding the proper
> indentation ..

this code i had rewritten and as fallout, the style changed.  looks
fine to me, and no, this particular checpatch "error" is not always
worthwhile (like in this case).
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Mon, 2009-09-14 at 18:17 -0400, Mike Frysinger wrote:
> 
> this code i had rewritten and as fallout, the style changed.  looks
> fine to me, and no, this particular checpatch "error" is not always
> worthwhile (like in this case).

Have you read Documentation/CodingStyle ? Can you better explain why
your don't want to follow that document ? Most people accept that to be
the style of code in Linux, and that is what checkpatch checks for..

We also have this quote from Documentation/SubmittingPatches

"4) Style check your changes.

Check your patch for basic style violations, details of which can be
found in Documentation/CodingStyle.  Failure to do so simply wastes
the reviewers time and will get your patch rejected, probably
without even being read.

At a minimum you should check your patches with the patch style
checker prior to submission (scripts/checkpatch.pl).  You should
be able to justify all violations that remain in your patch."

If you ultimately don't correct these changes, I'd ask that in the
future you submit pull requests for the blackfin architecture instead of
sending individual patches ..

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
> On Mon, 2009-09-14 at 18:17 -0400, Mike Frysinger wrote:
>> this code i had rewritten and as fallout, the style changed.  looks
>> fine to me, and no, this particular checpatch "error" is not always
>> worthwhile (like in this case).
>
> Have you read Documentation/CodingStyle ? Can you better explain why
> your don't want to follow that document ? Most people accept that to be
> the style of code in Linux, and that is what checkpatch checks for..

sorry, never heard of Documentation/
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
> If you ultimately don't correct these changes, I'd ask that in the
> future you submit pull requests for the blackfin architecture instead of
> sending individual patches ..

you havent been following anything related to how Blackfin (or any
arch?) patches are merged.  this patch series is for review only from
my tree.  no one is picking these up because they've already been
picked up.
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Tue, 2009-09-15 at 22:56 -0400, Mike Frysinger wrote:
> On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
> > If you ultimately don't correct these changes, I'd ask that in the
> > future you submit pull requests for the blackfin architecture instead of
> > sending individual patches ..
> 
> you havent been following anything related to how Blackfin (or any
> arch?) patches are merged.  this patch series is for review only from
> my tree.  no one is picking these up because they've already been
> picked up.

Picked up by Linus? You know this isn't the "blackfin" list right? You
don't seem to care too about review your getting from _this_ list. So
why in the world are you sending your patches (all 72 of them!) here ..

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Tue, Sep 15, 2009 at 23:06, Daniel Walker wrote:
> On Tue, 2009-09-15 at 22:56 -0400, Mike Frysinger wrote:
>> On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
>> > If you ultimately don't correct these changes, I'd ask that in the
>> > future you submit pull requests for the blackfin architecture instead of
>> > sending individual patches ..
>>
>> you havent been following anything related to how Blackfin (or any
>> arch?) patches are merged.  this patch series is for review only from
>> my tree.  no one is picking these up because they've already been
>> picked up.
>
> Picked up by Linus? You know this isn't the "blackfin" list right? You
> don't seem to care too about review your getting from _this_ list. So
> why in the world are you sending your patches (all 72 of them!) here ..

Linus doesnt pick up random patches, he does pull requests.  Blackfin
patches already get reviewed on the Blackfin list (during original
commit and later merge).  i post all the patches for sanity checking
things we may have missed (it happens).  any sane mailer makes it
trivial to delete/ignore a single thread, and for anyone reading LKML,
not using a sane mailer is a poor excuse.  i'm open to review of real
issues with the code (locking / leaks / design problems / etc...).
forcing a respin of patches for a minor style difference is noise.
-mike

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Daniel Walker]

On Tue, 2009-09-15 at 23:21 -0400, Mike Frysinger wrote:
> On Tue, Sep 15, 2009 at 23:06, Daniel Walker wrote:
> > On Tue, 2009-09-15 at 22:56 -0400, Mike Frysinger wrote:
> >> On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
> >> > If you ultimately don't correct these changes, I'd ask that in the
> >> > future you submit pull requests for the blackfin architecture instead of
> >> > sending individual patches ..
> >>
> >> you havent been following anything related to how Blackfin (or any
> >> arch?) patches are merged.  this patch series is for review only from
> >> my tree.  no one is picking these up because they've already been
> >> picked up.
> >
> > Picked up by Linus? You know this isn't the "blackfin" list right? You
> > don't seem to care too about review your getting from _this_ list. So
> > why in the world are you sending your patches (all 72 of them!) here ..
> 
> Linus doesnt pick up random patches, he does pull requests.  Blackfin
> patches already get reviewed on the Blackfin list (during original
> commit and later merge).  i post all the patches for sanity checking
> things we may have missed (it happens).  any sane mailer makes it
> trivial to delete/ignore a single thread, and for anyone reading LKML,
> not using a sane mailer is a poor excuse.  i'm open to review of real
> issues with the code (locking / leaks / design problems / etc...).
> forcing a respin of patches for a minor style difference is noise.

I read all of LKML, sane mailer or not _your_ patches are noise .. You
have your own mailing list. You have no good reason to post that many
patches here, and it's more than likely no one is reviewing them (except
me, and your ignoring my valid comments) .. If you have specific patches
that have questionable "locking, leaks, or design problems" that's
welcome, but not what your doing..

Daniel

Re: [PATCH 00/72] Blackfin updates for 2.6.32

[Mike Frysinger]

On Tue, Sep 15, 2009 at 23:59, Daniel Walker wrote:
> On Tue, 2009-09-15 at 23:21 -0400, Mike Frysinger wrote:
>> On Tue, Sep 15, 2009 at 23:06, Daniel Walker wrote:
>> > On Tue, 2009-09-15 at 22:56 -0400, Mike Frysinger wrote:
>> >> On Mon, Sep 14, 2009 at 18:36, Daniel Walker wrote:
>> >> > If you ultimately don't correct these changes, I'd ask that in the
>> >> > future you submit pull requests for the blackfin architecture instead of
>> >> > sending individual patches ..
>> >>
>> >> you havent been following anything related to how Blackfin (or any
>> >> arch?) patches are merged.  this patch series is for review only from
>> >> my tree.  no one is picking these up because they've already been
>> >> picked up.
>> >
>> > Picked up by Linus? You know this isn't the "blackfin" list right? You
>> > don't seem to care too about review your getting from _this_ list. So
>> > why in the world are you sending your patches (all 72 of them!) here ..
>>
>> Linus doesnt pick up random patches, he does pull requests.  Blackfin
>> patches already get reviewed on the Blackfin list (during original
>> commit and later merge).  i post all the patches for sanity checking
>> things we may have missed (it happens).  any sane mailer makes it
>> trivial to delete/ignore a single thread, and for anyone reading LKML,
>> not using a sane mailer is a poor excuse.  i'm open to review of real
>> issues with the code (locking / leaks / design problems / etc...).
>> forcing a respin of patches for a minor style difference is noise.
>
> I read all of LKML, sane mailer or not _your_ patches are noise .. You
> have your own mailing list. You have no good reason to post that many
> patches here, and it's more than likely no one is reviewing them (except
> me, and your ignoring my valid comments) .. If you have specific patches
> that have questionable "locking, leaks, or design problems" that's
> welcome, but not what your doing..

if i thought something had questionable code, i'd of fixed it myself,
or specifically asked someone.  if the larger lkml community would
prefer to not see the patch series for review, i have no program
refraining, but i havent seen a negative response so far.  i have seen
some random fixes which were certainly nice.
-mike