* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
@ 2010-01-28 12:16 Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 02/17] GRETH: Added support for selecting PHY address from config, PHY address was always set to zero before Daniel Hellstrom
` (17 more replies)
0 siblings, 18 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
include/asm-sparc/unaligned.h | 17 +++++++++++++++++
1 files changed, 17 insertions(+), 0 deletions(-)
create mode 100644 include/asm-sparc/unaligned.h
diff --git a/include/asm-sparc/unaligned.h b/include/asm-sparc/unaligned.h
new file mode 100644
index 0000000..4e604c1
--- /dev/null
+++ b/include/asm-sparc/unaligned.h
@@ -0,0 +1,17 @@
+#ifndef _ASM_SPARC_UNALIGNED_H
+#define _ASM_SPARC_UNALIGNED_H
+
+#ifdef __KERNEL__
+
+/*
+ * The SPARC can not do unaligned accesses, it must be split into multiple
+ * byte accesses. The SPARC is in big endian mode.
+ */
+#include <linux/unaligned/be_byteshift.h>
+#include <linux/unaligned/generic.h>
+
+#define get_unaligned __get_unaligned_be
+#define put_unaligned __put_unaligned_be
+
+#endif /* __KERNEL__ */
+#endif /* _ASM_SPARC_UNALIGNED_H */
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 02/17] GRETH: Added support for selecting PHY address from config, PHY address was always set to zero before.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 03/17] GRETH: Added extra RESET, this is needed if GRETH was stopped during an ethernet frame reception Daniel Hellstrom
` (16 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
drivers/net/greth.c | 69 +++++++++++++++++++++++++++++++-------------------
1 files changed, 43 insertions(+), 26 deletions(-)
diff --git a/drivers/net/greth.c b/drivers/net/greth.c
index 79bc4d9..833915d 100644
--- a/drivers/net/greth.c
+++ b/drivers/net/greth.c
@@ -45,7 +45,7 @@
/* ByPass Cache when reading regs */
#define GRETH_REGLOAD(addr) SPARC_NOCACHE_READ(addr)
/* Write-through cache ==> no bypassing needed on writes */
-#define GRETH_REGSAVE(addr,data) (*(unsigned int *)(addr) = (data))
+#define GRETH_REGSAVE(addr,data) (*(volatile unsigned int *)(addr) = (data))
#define GRETH_REGORIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)|data)
#define GRETH_REGANDIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)&data)
@@ -102,12 +102,12 @@ typedef struct {
} greth_priv;
/* Read MII register 'addr' from core 'regs' */
-static int read_mii(int addr, volatile greth_regs * regs)
+static int read_mii(int phyaddr, int regaddr, volatile greth_regs * regs)
{
while (GRETH_REGLOAD(®s->mdio) & GRETH_MII_BUSY) {
}
- GRETH_REGSAVE(®s->mdio, (0 << 11) | ((addr & 0x1F) << 6) | 2);
+ GRETH_REGSAVE(®s->mdio, ((phyaddr & 0x1F) << 11) | ((regaddr & 0x1F) << 6) | 2);
while (GRETH_REGLOAD(®s->mdio) & GRETH_MII_BUSY) {
}
@@ -119,14 +119,14 @@ static int read_mii(int addr, volatile greth_regs * regs)
}
}
-static void write_mii(int addr, int data, volatile greth_regs * regs)
+static void write_mii(int phyaddr, int regaddr, int data, volatile greth_regs * regs)
{
while (GRETH_REGLOAD(®s->mdio) & GRETH_MII_BUSY) {
}
GRETH_REGSAVE(®s->mdio,
- ((data & 0xFFFF) << 16) | (0 << 11) | ((addr & 0x1F) << 6)
- | 1);
+ ((data & 0xFFFF) << 16) | ((phyaddr & 0x1F) << 11) |
+ ((regaddr & 0x1F) << 6) | 1);
while (GRETH_REGLOAD(®s->mdio) & GRETH_MII_BUSY) {
}
@@ -146,8 +146,6 @@ int greth_init(struct eth_device *dev, bd_t * bis)
printf("greth_init\n");
#endif
- GRETH_REGSAVE(®s->control, 0);
-
if (!greth->rxbd_base) {
/* allocate descriptors */
@@ -161,6 +159,7 @@ int greth_init(struct eth_device *dev, bd_t * bis)
malloc(GRETH_RXBUF_EFF_SIZE * GRETH_RXBD_CNT);
}
+ memset(greth->rxbuf_base, 0, GRETH_RXBUF_EFF_SIZE * GRETH_RXBD_CNT);
/* initate rx decriptors */
for (i = 0; i < GRETH_RXBD_CNT; i++) {
greth->rxbd_base[i].addr = (unsigned int)
@@ -219,6 +218,11 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
greth_regs *regs = dev->regs;
int tmp, tmp1, tmp2, i;
unsigned int start, timeout;
+#ifdef CONFIG_SYS_GRLIB_GRETH_PHYADDR
+ int phyaddr = CONFIG_SYS_GRLIB_GRETH_PHYADDR;
+#else
+ int phyaddr = 0;
+#endif
/* X msecs to ticks */
timeout = usec2ticks(GRETH_PHY_TIMEOUT_MS * 1000);
@@ -230,17 +234,25 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
/* get phy control register default values */
- while ((tmp = read_mii(0, regs)) & 0x8000) {
- if (get_timer(start) > timeout)
+ while ((tmp = read_mii(phyaddr, 0, regs)) & 0x8000) {
+ if (get_timer(start) > timeout) {
+#ifdef DEBUG
+ printf("greth_init_phy: PHY read 1 failed\n");
+#endif
return 1; /* Fail */
+ }
}
/* reset PHY and wait for completion */
- write_mii(0, 0x8000 | tmp, regs);
+ write_mii(phyaddr, 0, 0x8000 | tmp, regs);
- while (((tmp = read_mii(0, regs))) & 0x8000) {
- if (get_timer(start) > timeout)
+ while (((tmp = read_mii(phyaddr, 0, regs))) & 0x8000) {
+ if (get_timer(start) > timeout) {
+#ifdef DEBUG
+ printf("greth_init_phy: PHY read 2 failed\n");
+#endif
return 1; /* Fail */
+ }
}
/* Check if PHY is autoneg capable and then determine operating
@@ -251,16 +263,16 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
dev->sp = 0;
dev->auto_neg = 0;
if (!((tmp >> 12) & 1)) {
- write_mii(0, 0, regs);
+ write_mii(phyaddr, 0, 0, regs);
} else {
/* wait for auto negotiation to complete and then check operating mode */
dev->auto_neg = 1;
i = 0;
- while (!(((tmp = read_mii(1, regs)) >> 5) & 1)) {
+ while (!(((tmp = read_mii(phyaddr, 1, regs)) >> 5) & 1)) {
if (get_timer(start) > timeout) {
printf("Auto negotiation timed out. "
"Selecting default config\n");
- tmp = read_mii(0, regs);
+ tmp = read_mii(phyaddr, 0, regs);
dev->gb = ((tmp >> 6) & 1)
&& !((tmp >> 13) & 1);
dev->sp = !((tmp >> 6) & 1)
@@ -270,8 +282,8 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
}
}
if ((tmp >> 8) & 1) {
- tmp1 = read_mii(9, regs);
- tmp2 = read_mii(10, regs);
+ tmp1 = read_mii(phyaddr, 9, regs);
+ tmp2 = read_mii(phyaddr, 10, regs);
if ((tmp1 & GRETH_MII_EXTADV_1000FD) &&
(tmp2 & GRETH_MII_EXTPRT_1000FD)) {
dev->gb = 1;
@@ -284,8 +296,8 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
}
}
if ((dev->gb == 0) || ((dev->gb == 1) && (dev->gbit_mac == 0))) {
- tmp1 = read_mii(4, regs);
- tmp2 = read_mii(5, regs);
+ tmp1 = read_mii(phyaddr, 4, regs);
+ tmp2 = read_mii(phyaddr, 5, regs);
if ((tmp1 & GRETH_MII_100TXFD) &&
(tmp2 & GRETH_MII_100TXFD)) {
dev->sp = 1;
@@ -302,7 +314,7 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
if ((dev->gb == 1) && (dev->gbit_mac == 0)) {
dev->gb = 0;
dev->fd = 0;
- write_mii(0, dev->sp << 13, regs);
+ write_mii(phyaddr, 0, dev->sp << 13, regs);
}
}
@@ -314,8 +326,8 @@ int greth_init_phy(greth_priv * dev, bd_t * bis)
#endif
/* Read out PHY info if extended registers are available */
if (tmp & 1) {
- tmp1 = read_mii(2, regs);
- tmp2 = read_mii(3, regs);
+ tmp1 = read_mii(phyaddr, 2, regs);
+ tmp2 = read_mii(phyaddr, 3, regs);
tmp1 = (tmp1 << 6) | ((tmp2 >> 10) & 0x3F);
tmp = tmp2 & 0xF;
@@ -542,10 +554,9 @@ int greth_recv(struct eth_device *dev)
/* increase index */
greth->rxbd_curr =
((unsigned int)greth->rxbd_curr >=
- (unsigned int)greth->rxbd_max) ? greth->
- rxbd_base : (greth->rxbd_curr + 1);
+ (unsigned int)greth->rxbd_max) ? greth->rxbd_base : (greth->rxbd_curr + 1);
- };
+ }
if (enable) {
GRETH_REGORIN(®s->control, GRETH_RXEN);
@@ -630,6 +641,9 @@ int greth_initialize(bd_t * bis)
/* initiate PHY, select speed/duplex depending on connected PHY */
if (greth_init_phy(greth, bis)) {
/* Failed to init PHY (timedout) */
+#ifdef DEBUG
+ printf("GRETH[0x%08x]: Failed to init PHY\n", greth->regs);
+#endif
return -1;
}
@@ -658,5 +672,8 @@ int greth_initialize(bd_t * bis)
/* set and remember MAC address */
greth_set_hwaddr(greth, addr);
+#ifdef DEBUG
+ printf("GRETH[0x%08x]: Initialized successfully\n", greth->regs);
+#endif
return 0;
}
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 03/17] GRETH: Added extra RESET, this is needed if GRETH was stopped during an ethernet frame reception.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 02/17] GRETH: Added support for selecting PHY address from config, PHY address was always set to zero before Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 04/17] LEON3: reimplemented AMBA Plug&Play scanning routines Daniel Hellstrom
` (15 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
drivers/net/greth.c | 14 ++++++++++++--
1 files changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/net/greth.c b/drivers/net/greth.c
index 833915d..383b25c 100644
--- a/drivers/net/greth.c
+++ b/drivers/net/greth.c
@@ -146,13 +146,23 @@ int greth_init(struct eth_device *dev, bd_t * bis)
printf("greth_init\n");
#endif
+ /* Reset core */
+ GRETH_REGSAVE(®s->control, (GRETH_RESET | (greth->gb << 8) |
+ (greth->sp << 7) | (greth->fd << 4)));
+
+ /* Wait for Reset to complete */
+ while ( GRETH_REGLOAD(®s->control) & GRETH_RESET) ;
+
+ GRETH_REGSAVE(®s->control,
+ ((greth->gb << 8) | (greth->sp << 7) | (greth->fd << 4)));
+
if (!greth->rxbd_base) {
/* allocate descriptors */
greth->rxbd_base = (greth_bd *)
memalign(0x1000, GRETH_RXBD_CNT * sizeof(greth_bd));
greth->txbd_base = (greth_bd *)
- memalign(0x1000, GRETH_RXBD_CNT * sizeof(greth_bd));
+ memalign(0x1000, GRETH_TXBD_CNT * sizeof(greth_bd));
/* allocate buffers to all descriptors */
greth->rxbuf_base =
@@ -185,7 +195,7 @@ int greth_init(struct eth_device *dev, bd_t * bis)
for (i = 0; i < GRETH_TXBD_CNT; i++) {
greth->txbd_base[i].addr = 0;
/* enable desciptor & set wrap bit if last descriptor */
- if (i >= (GRETH_RXBD_CNT - 1)) {
+ if (i >= (GRETH_TXBD_CNT - 1)) {
greth->txbd_base[i].stat = GRETH_BD_WR;
} else {
greth->txbd_base[i].stat = 0;
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 04/17] LEON3: reimplemented AMBA Plug&Play scanning routines.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 02/17] GRETH: Added support for selecting PHY address from config, PHY address was always set to zero before Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 03/17] GRETH: Added extra RESET, this is needed if GRETH was stopped during an ethernet frame reception Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 05/17] LEON3: added memory controller initialization using the new AMBA PnP routines Daniel Hellstrom
` (14 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
common/cmd_ambapp.c | 566 +++++++++++++++++++++++++-------
cpu/leon3/Makefile | 2 +-
cpu/leon3/ambapp.c | 581 +++++++++++++++++-----------------
cpu/leon3/ambapp_low.S | 798 ++++++++++++++++++++++++++++++++++++++++++++++
cpu/leon3/ambapp_low_c.S | 133 ++++++++
cpu/leon3/cpu_init.c | 182 ++++-------
cpu/leon3/serial.c | 8 +-
cpu/leon3/usb_uhci.c | 4 +-
drivers/net/greth.c | 15 +-
include/ambapp.h | 365 ++++++++++-----------
include/ambapp_ids.h | 256 +++++++++++++++
11 files changed, 2180 insertions(+), 730 deletions(-)
create mode 100644 cpu/leon3/ambapp_low.S
create mode 100644 cpu/leon3/ambapp_low_c.S
create mode 100644 include/ambapp_ids.h
diff --git a/common/cmd_ambapp.c b/common/cmd_ambapp.c
index bb20ab5..55b2757 100644
--- a/common/cmd_ambapp.c
+++ b/common/cmd_ambapp.c
@@ -31,92 +31,380 @@
DECLARE_GLOBAL_DATA_PTR;
-/* We put these variables into .data section so that they are zero
- * when entering the AMBA Plug & Play routines (in cpu/cpu/ambapp.c)
- * the first time. BSS is not garantueed to be zero since BSS
- * hasn't been cleared the first times entering the CPU AMBA functions.
- *
- * The AMBA PnP routines call these functions if ambapp_???_print is set.
- *
- */
-int ambapp_apb_print __attribute__ ((section(".data"))) = 0;
-int ambapp_ahb_print __attribute__ ((section(".data"))) = 0;
-
typedef struct {
int device_id;
char *name;
+ char *desc;
} ambapp_device_name;
-static ambapp_device_name gaisler_devices[] = {
- {GAISLER_LEON3, "GAISLER_LEON3"},
- {GAISLER_LEON3DSU, "GAISLER_LEON3DSU"},
- {GAISLER_ETHAHB, "GAISLER_ETHAHB"},
- {GAISLER_ETHMAC, "GAISLER_ETHMAC"},
- {GAISLER_APBMST, "GAISLER_APBMST"},
- {GAISLER_AHBUART, "GAISLER_AHBUART"},
- {GAISLER_SRCTRL, "GAISLER_SRCTRL"},
- {GAISLER_SDCTRL, "GAISLER_SDCTRL"},
- {GAISLER_APBUART, "GAISLER_APBUART"},
- {GAISLER_IRQMP, "GAISLER_IRQMP"},
- {GAISLER_AHBRAM, "GAISLER_AHBRAM"},
- {GAISLER_GPTIMER, "GAISLER_GPTIMER"},
- {GAISLER_PCITRG, "GAISLER_PCITRG"},
- {GAISLER_PCISBRG, "GAISLER_PCISBRG"},
- {GAISLER_PCIFBRG, "GAISLER_PCIFBRG"},
- {GAISLER_PCITRACE, "GAISLER_PCITRACE"},
- {GAISLER_AHBTRACE, "GAISLER_AHBTRACE"},
- {GAISLER_ETHDSU, "GAISLER_ETHDSU"},
- {GAISLER_PIOPORT, "GAISLER_PIOPORT"},
- {GAISLER_AHBJTAG, "GAISLER_AHBJTAG"},
- {GAISLER_ATACTRL, "GAISLER_ATACTRL"},
- {GAISLER_VGA, "GAISLER_VGA"},
- {GAISLER_KBD, "GAISLER_KBD"},
- {GAISLER_L2TIME, "GAISLER_L2TIME"},
- {GAISLER_L2C, "GAISLER_L2C"},
- {GAISLER_PLUGPLAY, "GAISLER_PLUGPLAY"},
- {GAISLER_SPW, "GAISLER_SPW"},
- {GAISLER_SPW2, "GAISLER_SPW2"},
- {GAISLER_EHCI, "GAISLER_EHCI"},
- {GAISLER_UHCI, "GAISLER_UHCI"},
- {GAISLER_AHBSTAT, "GAISLER_AHBSTAT"},
- {GAISLER_DDR2SPA, "GAISLER_DDR2SPA"},
- {GAISLER_DDRSPA, "GAISLER_DDRSPA"},
- {0, NULL}
+typedef struct {
+ unsigned int vendor_id;
+ char *name;
+ char *desc;
+ ambapp_device_name *devices;
+} ambapp_vendor_devnames;
+
+/** Vendor GAISLER devices */
+static ambapp_device_name GAISLER_devices[] =
+{
+ {GAISLER_LEON2DSU, "LEON2DSU", "Leon2 Debug Support Unit"},
+ {GAISLER_LEON3, "LEON3", "Leon3 SPARC V8 Processor"},
+ {GAISLER_LEON3DSU, "LEON3DSU", "Leon3 Debug Support Unit"},
+ {GAISLER_ETHAHB, "ETHAHB", "OC ethernet AHB interface"},
+ {GAISLER_APBMST, "APBMST", "AHB/APB Bridge"},
+ {GAISLER_AHBUART, "AHBUART", "AHB Debug UART"},
+ {GAISLER_SRCTRL, "SRCTRL", "Simple SRAM Controller"},
+ {GAISLER_SDCTRL, "SDCTRL", "PC133 SDRAM Controller"},
+ {GAISLER_SSRCTRL, "SSRCTRL", "Synchronous SRAM Controller"},
+ {GAISLER_APBUART, "APBUART", "Generic UART"},
+ {GAISLER_IRQMP, "IRQMP", "Multi-processor Interrupt Ctrl."},
+ {GAISLER_AHBRAM, "AHBRAM", "Single-port AHB SRAM module"},
+ {GAISLER_AHBDPRAM, "AHBDPRAM", "Dual-port AHB SRAM module"},
+ {GAISLER_GPTIMER, "GPTIMER", "Modular Timer Unit"},
+ {GAISLER_PCITRG, "PCITRG", "Simple 32-bit PCI Target"},
+ {GAISLER_PCISBRG, "PCISBRG", "Simple 32-bit PCI Bridge"},
+ {GAISLER_PCIFBRG, "PCIFBRG", "Fast 32-bit PCI Bridge"},
+ {GAISLER_PCITRACE, "PCITRACE", "32-bit PCI Trace Buffer"},
+ {GAISLER_DMACTRL, "DMACTRL", "AMBA DMA controller"},
+ {GAISLER_AHBTRACE, "AHBTRACE", "AMBA Trace Buffer"},
+ {GAISLER_DSUCTRL, "DSUCTRL", "DSU/ETH controller"},
+ {GAISLER_CANAHB, "CANAHB", "OC CAN AHB interface"},
+ {GAISLER_GPIO, "GPIO", "General Purpose I/O port"},
+ {GAISLER_AHBROM, "AHBROM", "Generic AHB ROM"},
+ {GAISLER_AHBJTAG, "AHBJTAG", "JTAG Debug Link"},
+ {GAISLER_ETHMAC, "ETHMAC", "GR Ethernet MAC"},
+ {GAISLER_SWNODE, "SWNODE", "SpaceWire Node Interface"},
+ {GAISLER_SPW, "SPW", "SpaceWire Serial Link"},
+ {GAISLER_AHB2AHB, "AHB2AHB", "AHB-to-AHB Bridge"},
+ {GAISLER_USBDC, "USBDC", "GR USB 2.0 Device Controller"},
+ {GAISLER_USB_DCL, "USB_DCL", "USB Debug Communication Link"},
+ {GAISLER_DDRMP, "DDRMP", "Multi-port DDR controller"},
+ {GAISLER_ATACTRL, "ATACTRL", "ATA controller"},
+ {GAISLER_DDRSP, "DDRSP", "Single-port DDR266 controller"},
+ {GAISLER_EHCI, "EHCI", "USB Enhanced Host Controller"},
+ {GAISLER_UHCI, "UHCI", "USB Universal Host Controller"},
+ {GAISLER_I2CMST, "I2CMST", "AMBA Wrapper for OC I2C-master"},
+ {GAISLER_SPW2, "SPW2", "GRSPW2 SpaceWire Serial Link"},
+ {GAISLER_AHBDMA, "AHBDMA", ""},
+ {GAISLER_NUHOSP3, "NUHOSP3", "Nuhorizons Spartan3 IO I/F"},
+ {GAISLER_CLKGATE, "CLKGATE", "Clock gating unit"},
+ {GAISLER_SPICTRL, "SPICTRL", "SPI Controller"},
+ {GAISLER_DDR2SP, "DDR2SP", "Single-port DDR2 controller"},
+ {GAISLER_SLINK, "SLINK", "SLINK Master"},
+ {GAISLER_GRTM, "GRTM", "CCSDS Telemetry Encoder"},
+ {GAISLER_GRTC, "GRTC", "CCSDS Telecommand Decoder"},
+ {GAISLER_GRPW, "GRPW", "PacketWire to AMBA AHB I/F"},
+ {GAISLER_GRCTM, "GRCTM", "CCSDS Time Manager"},
+ {GAISLER_GRHCAN, "GRHCAN", "ESA HurriCANe CAN with DMA"},
+ {GAISLER_GRFIFO, "GRFIFO", "FIFO Controller"},
+ {GAISLER_GRADCDAC, "GRADCDAC", "ADC / DAC Interface"},
+ {GAISLER_GRPULSE, "GRPULSE", "General Purpose I/O with Pulses"},
+ {GAISLER_GRTIMER, "GRTIMER", "Timer Unit with Latches"},
+ {GAISLER_AHB2PP, "AHB2PP", "AMBA AHB to Packet Parallel I/F"},
+ {GAISLER_GRVERSION, "GRVERSION", "Version and Revision Register"},
+ {GAISLER_APB2PW, "APB2PW", "PacketWire Transmit Interface"},
+ {GAISLER_PW2APB, "PW2APB", "PacketWire Receive Interface"},
+ {GAISLER_GRCAN, "GRCAN", "CAN Controller with DMA"},
+ {GAISLER_I2CSLV, "I2CSLV", "I2C Slave"},
+ {GAISLER_U16550, "U16550", "Simple 16550 UART"},
+ {GAISLER_AHBMST_EM, "AHBMST_EM", "AMBA Master Emulator"},
+ {GAISLER_AHBSLV_EM, "AHBSLV_EM", "AMBA Slave Emulator"},
+ {GAISLER_GRTESTMOD, "GRTESTMOD", "Test report module"},
+ {GAISLER_ASCS, "ASCS", "ASCS Master"},
+ {GAISLER_IPMVBCTRL, "IPMVBCTRL", "IPM-bus/MVBC memory controller"},
+ {GAISLER_SPIMCTRL, "SPIMCTRL", "SPI Memory Controller"},
+ {GAISLER_LEON4, "LEON4", "Leon4 SPARC V8 Processor"},
+ {GAISLER_LEON4DSU, "LEON4DSU", "Leon4 Debug Support Unit"},
+ {GAISLER_PWM, "PWM", "PWM generator"},
+ {GAISLER_L2CACHE, "L2CACHE", "L2-Cache Controller"},
+ {GAISLER_SDCTRL64, "SDCTRL64", ""},
+ {GAISLER_FTAHBRAM, "FTAHBRAM", "Generic FT AHB SRAM module"},
+ {GAISLER_FTSRCTRL, "FTSRCTRL", "Simple FT SRAM Controller"},
+ {GAISLER_AHBSTAT, "AHBSTAT", "AHB Status Register"},
+ {GAISLER_LEON3FT, "LEON3FT", "Leon3-FT SPARC V8 Processor"},
+ {GAISLER_FTMCTRL, "FTMCTRL", "Memory controller with EDAC"},
+ {GAISLER_FTSDCTRL, "FTSDCTRL", "FT PC133 SDRAM Controller"},
+ {GAISLER_FTSRCTRL8, "FTSRCTRL8", "FT 8-bit SRAM/16-bit IO Ctrl"},
+ {GAISLER_APBPS2, "APBPS2", "PS2 interface"},
+ {GAISLER_VGACTRL, "VGACTRL", "VGA controller"},
+ {GAISLER_LOGAN, "LOGAN", "On chip Logic Analyzer"},
+ {GAISLER_SVGACTRL, "SVGACTRL", "SVGA frame buffer"},
+ {GAISLER_T1AHB, "T1AHB", "Niagara T1 PCX/AHB bridge"},
+ {GAISLER_MP7WRAP, "MP7WRAP", "CoreMP7 wrapper"},
+ {GAISLER_GRSYSMON, "GRSYSMON", "AMBA wrapper for System Monitor"},
+ {GAISLER_GRACECTRL, "GRACECTRL", "System ACE I/F Controller"},
+ {GAISLER_ATAHBSLV, "ATAHBSLV", "AMBA Test Framework AHB Slave"},
+ {GAISLER_ATAHBMST, "ATAHBMST", "AMBA Test Framework AHB Master"},
+ {GAISLER_ATAPBSLV, "ATAPBSLV", "AMBA Test Framework APB Slave"},
+ {GAISLER_B1553BC, "B1553BC", "AMBA Wrapper for Core1553BBC"},
+ {GAISLER_B1553RT, "B1553RT", "AMBA Wrapper for Core1553BRT"},
+ {GAISLER_B1553BRM, "B1553BRM", "AMBA Wrapper for Core1553BRM"},
+ {GAISLER_AES, "AES", "Advanced Encryption Standard"},
+ {GAISLER_ECC, "ECC", "Elliptic Curve Cryptography"},
+ {GAISLER_PCIF, "PCIF", "AMBA Wrapper for CorePCIF"},
+ {GAISLER_CLKMOD, "CLKMOD", "CPU Clock Switching Ctrl module"},
+ {GAISLER_HAPSTRAK, "HAPSTRAK", "HAPS HapsTrak I/O Port"},
+ {GAISLER_TEST_1X2, "TEST_1X2", "HAPS TEST_1x2 interface"},
+ {GAISLER_WILD2AHB, "WILD2AHB", "WildCard CardBus interface"},
+ {GAISLER_BIO1, "BIO1", "Basic I/O board BIO1"},
+ {GAISLER_SATCAN, "SATCAN", "SatCAN controller"},
+ {GAISLER_CANMUX, "CANMUX", "CAN Bus multiplexer"},
+ {GAISLER_GRTMRX, "GRTMRX", "CCSDS Telemetry Receiver"},
+ {GAISLER_GRTCTX, "GRTCTX", "CCSDS Telecommand Transmitter"},
+ {GAISLER_GRTMDESC, "GRTMDESC", "CCSDS Telemetry Descriptor"},
+ {GAISLER_GRTMVC, "GRTMVC", "CCSDS Telemetry VC Generator"},
+ {GAISLER_GEFFE, "GEFFE", "Geffe Generator"},
+ {GAISLER_GPREG, "GPREG", ""},
+ {GAISLER_GRTMPAHB, "GRTMPAHB", "CCSDS Telemetry VC AHB Input"},
+ {0, NULL, NULL}
};
-static ambapp_device_name esa_devices[] = {
- {ESA_LEON2, "ESA_LEON2"},
- {ESA_MCTRL, "ESA_MCTRL"},
- {0, NULL}
+
+/** Vendor PENDER devices */
+static ambapp_device_name PENDER_devices[] =
+{
+ {0, NULL, NULL}
};
-static ambapp_device_name opencores_devices[] = {
- {OPENCORES_PCIBR, "OPENCORES_PCIBR"},
- {OPENCORES_ETHMAC, "OPENCORES_ETHMAC"},
+
+/** Vendor ESA devices */
+static ambapp_device_name ESA_devices[] =
+{
+ {ESA_LEON2, "LEON2", "Leon2 SPARC V8 Processor"},
+ {ESA_LEON2APB, "LEON2APB", "Leon2 Peripheral Bus"},
+ {ESA_IRQ, "IRQ", "Leon2 Interrupt Controller"},
+ {ESA_TIMER, "TIMER", "Leon2 Timer"},
+ {ESA_UART, "UART", "Leon2 UART"},
+ {ESA_CFG, "CFG", "Leon2 Configuration Register"},
+ {ESA_IO, "IO", "Leon2 Input/Output"},
+ {ESA_MCTRL, "MCTRL", "Leon2 Memory Controller"},
+ {ESA_PCIARB, "PCIARB", "PCI Arbiter"},
+ {ESA_HURRICANE, "HURRICANE", "HurriCANe/HurryAMBA CAN Ctrl"},
+ {ESA_SPW_RMAP, "SPW_RMAP", "UoD/Saab SpaceWire/RMAP link"},
+ {ESA_AHBUART, "AHBUART", "Leon2 AHB Debug UART"},
+ {ESA_SPWA, "SPWA", "ESA/ASTRIUM SpaceWire link"},
+ {ESA_BOSCHCAN, "BOSCHCAN", "SSC/BOSCH CAN Ctrl"},
+ {ESA_IRQ2, "IRQ2", "Leon2 Secondary Irq Controller"},
+ {ESA_AHBSTAT, "AHBSTAT", "Leon2 AHB Status Register"},
+ {ESA_WPROT, "WPROT", "Leon2 Write Protection"},
+ {ESA_WPROT2, "WPROT2", "Leon2 Extended Write Protection"},
+ {ESA_PDEC3AMBA, "PDEC3AMBA", "ESA CCSDS PDEC3AMBA TC Decoder"},
+ {ESA_PTME3AMBA, "PTME3AMBA", "ESA CCSDS PTME3AMBA TM Encoder"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor ASTRIUM devices */
+static ambapp_device_name ASTRIUM_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor OPENCHIP devices */
+static ambapp_device_name OPENCHIP_devices[] =
+{
+ {OPENCHIP_APBGPIO, "APBGPIO", "APB General Purpose IO"},
+ {OPENCHIP_APBI2C, "APBI2C", "APB I2C Interface"},
+ {OPENCHIP_APBSPI, "APBSPI", "APB SPI Interface"},
+ {OPENCHIP_APBCHARLCD, "APBCHARLCD", "APB Character LCD"},
+ {OPENCHIP_APBPWM, "APBPWM", "APB PWM"},
+ {OPENCHIP_APBPS2, "APBPS2", "APB PS/2 Interface"},
+ {OPENCHIP_APBMMCSD, "APBMMCSD", "APB MMC/SD Card Interface"},
+ {OPENCHIP_APBNAND, "APBNAND", "APB NAND(SmartMedia) Interface"},
+ {OPENCHIP_APBLPC, "APBLPC", "APB LPC Interface"},
+ {OPENCHIP_APBCF, "APBCF", "APB CompactFlash (IDE)"},
+ {OPENCHIP_APBSYSACE, "APBSYSACE", "APB SystemACE Interface"},
+ {OPENCHIP_APB1WIRE, "APB1WIRE", "APB 1-Wire Interface"},
+ {OPENCHIP_APBJTAG, "APBJTAG", "APB JTAG TAP Master"},
+ {OPENCHIP_APBSUI, "APBSUI", "APB Simple User Interface"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor OPENCORES devices */
+static ambapp_device_name OPENCORES_devices[] =
+{
+ {OPENCORES_PCIBR, "PCIBR", "PCI Bridge"},
+ {OPENCORES_ETHMAC, "ETHMAC", "Ethernet MAC"},
{0, NULL}
};
-typedef struct {
- unsigned int vendor_id;
- char *name;
- ambapp_device_name *devices;
-} ambapp_vendor_devnames;
-
-static ambapp_vendor_devnames vendors[] = {
- {VENDOR_GAISLER, "VENDOR_GAISLER", gaisler_devices},
- {VENDOR_ESA, "VENDOR_ESA", esa_devices},
- {VENDOR_OPENCORES, "VENDOR_OPENCORES", opencores_devices},
- {0, NULL, 0}
+
+/** Vendor CONTRIB devices */
+static ambapp_device_name CONTRIB_devices[] =
+{
+ {CONTRIB_CORE1, "CORE1", "Contributed core 1"},
+ {CONTRIB_CORE2, "CORE2", "Contributed core 2"},
+ {0, NULL, NULL}
};
-static char *ambapp_get_devname(ambapp_device_name * devs, int id)
+
+/** Vendor EONIC devices */
+static ambapp_device_name EONIC_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor RADIONOR devices */
+static ambapp_device_name RADIONOR_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor GLEICHMANN devices */
+static ambapp_device_name GLEICHMANN_devices[] =
+{
+ {GLEICHMANN_CUSTOM, "CUSTOM", "Custom device"},
+ {GLEICHMANN_GEOLCD01, "GEOLCD01", "GEOLCD01 graphics system"},
+ {GLEICHMANN_DAC, "DAC", "Sigma delta DAC"},
+ {GLEICHMANN_HPI, "HPI", "AHB-to-HPI bridge"},
+ {GLEICHMANN_SPI, "SPI", "SPI master"},
+ {GLEICHMANN_HIFC, "HIFC", "Human interface controller"},
+ {GLEICHMANN_ADCDAC, "ADCDAC", "Sigma delta ADC/DAC"},
+ {GLEICHMANN_SPIOC, "SPIOC", ""},
+ {GLEICHMANN_AC97, "AC97", ""},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor MENTA devices */
+static ambapp_device_name MENTA_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor SUN devices */
+static ambapp_device_name SUN_devices[] =
+{
+ {SUN_T1, "T1", "Niagara T1 SPARC V9 Processor"},
+ {SUN_S1, "S1", "Niagara S1 SPARC V9 Processor"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor MOVIDIA devices */
+static ambapp_device_name MOVIDIA_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor ORBITA devices */
+static ambapp_device_name ORBITA_devices[] =
+{
+ {ORBITA_1553B, "1553B", "MIL-STD-1553B Controller"},
+ {ORBITA_429, "429", "429 Interface"},
+ {ORBITA_SPI, "SPI", "SPI Interface"},
+ {ORBITA_I2C, "I2C", "I2C Interface"},
+ {ORBITA_SMARTCARD, "SMARTCARD", "Smart Card Reader"},
+ {ORBITA_SDCARD, "SDCARD", "SD Card Reader"},
+ {ORBITA_UART16550, "UART16550", "16550 UART"},
+ {ORBITA_CRYPTO, "CRYPTO", "Crypto Engine"},
+ {ORBITA_SYSIF, "SYSIF", "System Interface"},
+ {ORBITA_PIO, "PIO", "Programmable IO module"},
+ {ORBITA_RTC, "RTC", "Real-Time Clock"},
+ {ORBITA_COLORLCD, "COLORLCD", "Color LCD Controller"},
+ {ORBITA_PCI, "PCI", "PCI Module"},
+ {ORBITA_DSP, "DSP", "DPS Co-Processor"},
+ {ORBITA_USBHOST, "USBHOST", "USB Host"},
+ {ORBITA_USBDEV, "USBDEV", "USB Device"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor SYNOPSYS devices */
+static ambapp_device_name SYNOPSYS_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor NASA devices */
+static ambapp_device_name NASA_devices[] =
+{
+ {NASA_EP32, "EP32", "EP32 Forth processor"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor CAL devices */
+static ambapp_device_name CAL_devices[] =
+{
+ {CAL_DDRCTRL, "DDRCTRL", ""},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor EMBEDDIT devices */
+static ambapp_device_name EMBEDDIT_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor CETON devices */
+static ambapp_device_name CETON_devices[] =
+{
+ {0, NULL, NULL}
+};
+
+
+/** Vendor ACTEL devices */
+static ambapp_device_name ACTEL_devices[] =
+{
+ {ACTEL_COREMP7, "COREMP7", "CoreMP7 Processor"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendor APPLECORE devices */
+static ambapp_device_name APPLECORE_devices[] =
+{
+ {APPLECORE_UTLEON3, "UTLEON3", "AppleCore uT-LEON3 Processor"},
+ {APPLECORE_UTLEON3DSU, "UTLEON3DSU", "AppleCore uT-LEON3 DSU"},
+ {0, NULL, NULL}
+};
+
+
+/** Vendors and their devices */
+static ambapp_vendor_devnames vendors[] =
+{
+ {VENDOR_GAISLER, "GAISLER", "Gaisler Research", GAISLER_devices},
+ {VENDOR_PENDER, "PENDER", "", PENDER_devices},
+ {VENDOR_ESA, "ESA", "European Space Agency", ESA_devices},
+ {VENDOR_ASTRIUM, "ASTRIUM", "", ASTRIUM_devices},
+ {VENDOR_OPENCHIP, "OPENCHIP", "OpenChip", OPENCHIP_devices},
+ {VENDOR_OPENCORES, "OPENCORES", "OpenCores", OPENCORES_devices},
+ {VENDOR_CONTRIB, "CONTRIB", "Various contributions", CONTRIB_devices},
+ {VENDOR_EONIC, "EONIC", "Eonic BV", EONIC_devices},
+ {VENDOR_RADIONOR, "RADIONOR", "Radionor Communications", RADIONOR_devices},
+ {VENDOR_GLEICHMANN, "GLEICHMANN", "Gleichmann Electronics", GLEICHMANN_devices},
+ {VENDOR_MENTA, "MENTA", "Menta", MENTA_devices},
+ {VENDOR_SUN, "SUN", "Sun Microsystems", SUN_devices},
+ {VENDOR_MOVIDIA, "MOVIDIA", "", MOVIDIA_devices},
+ {VENDOR_ORBITA, "ORBITA", "Orbita", ORBITA_devices},
+ {VENDOR_SYNOPSYS, "SYNOPSYS", "Synopsys Inc.", SYNOPSYS_devices},
+ {VENDOR_NASA, "NASA", "NASA", NASA_devices},
+ {VENDOR_CAL, "CAL", "", CAL_devices},
+ {VENDOR_EMBEDDIT, "EMBEDDIT", "Embedd.it", EMBEDDIT_devices},
+ {VENDOR_CETON, "CETON", "Ceton Corporation", CETON_devices},
+ {VENDOR_ACTEL, "ACTEL", "Actel Corporation", ACTEL_devices},
+ {VENDOR_APPLECORE, "APPLECORE", "AppleCore", APPLECORE_devices},
+ {0, NULL, NULL, NULL}
+};
+
+static ambapp_device_name *ambapp_get_dev(ambapp_device_name * devs, int id)
{
if (!devs)
return NULL;
while (devs->device_id > 0) {
if (devs->device_id == id)
- return devs->name;
+ return devs;
devs++;
}
return NULL;
@@ -125,10 +413,31 @@ static char *ambapp_get_devname(ambapp_device_name * devs, int id)
char *ambapp_device_id2str(int vendor, int id)
{
ambapp_vendor_devnames *ven = &vendors[0];
+ ambapp_device_name *dev;
+
+ while (ven->vendor_id > 0) {
+ if (ven->vendor_id == vendor) {
+ dev = ambapp_get_dev(ven->devices, id);
+ if ( !dev )
+ return NULL;
+ return dev->name;
+ }
+ ven++;
+ }
+ return NULL;
+}
+
+char *ambapp_device_id2desc(int vendor, int id)
+{
+ ambapp_vendor_devnames *ven = &vendors[0];
+ ambapp_device_name *dev;
while (ven->vendor_id > 0) {
if (ven->vendor_id == vendor) {
- return ambapp_get_devname(ven->devices, id);
+ dev = ambapp_get_dev(ven->devices, id);
+ if ( !dev )
+ return NULL;
+ return dev->desc;
}
ven++;
}
@@ -150,101 +459,107 @@ char *ambapp_vendor_id2str(int vendor)
static char *unknown = "unknown";
+char *ambapp_type_names[4] =
+{
+ /* 0 */ "UNUSED",
+ /* 1 */ "apb",
+ /* 2 */ "ahbmem",
+ /* 3 */ "ahbio"
+};
+
/* Print one APB device */
-void ambapp_print_apb(apbctrl_pp_dev * apb, ambapp_ahbdev * apbmst, int index)
+void ambapp_print_apb(ambapp_apbdev *dev, int index)
{
char *dev_str, *ven_str;
- int irq, ver, vendor, deviceid;
- unsigned int address, apbmst_base, mask;
-
- vendor = amba_vendor(apb->conf);
- deviceid = amba_device(apb->conf);
- irq = amba_irq(apb->conf);
- ver = amba_ver(apb->conf);
- apbmst_base = apbmst->address[0] & LEON3_IO_AREA;
- address = (apbmst_base | (((apb->bar & 0xfff00000) >> 12))) &
- (((apb->bar & 0x0000fff0) << 4) | 0xfff00000);
-
- mask = amba_membar_mask(apb->bar) << 8;
- mask = ((~mask) & 0x000fffff) + 1;
+ unsigned int freq;
- ven_str = ambapp_vendor_id2str(vendor);
+ ven_str = ambapp_vendor_id2str(dev->vendor);
if (!ven_str) {
ven_str = unknown;
dev_str = unknown;
} else {
- dev_str = ambapp_device_id2str(vendor, deviceid);
+ dev_str = ambapp_device_id2str(dev->vendor, dev->device);
if (!dev_str)
dev_str = unknown;
}
+
+ /* Get Frequency of Core */
+ freq = ambapp_bus_freq(&ambapp_plb, dev->ahb_bus_index);
- printf("0x%02x:0x%02x:0x%02x: %s %s\n"
+ printf("0x%02x:0x%02x:0x%02x: %s %s (%dkHz)\n"
" apb: 0x%08x - 0x%08x\n"
" irq: %-2d (ver: %-2d)\n",
- index, vendor, deviceid, ven_str, dev_str, address,
- address + mask, irq, ver);
+ index, dev->vendor, dev->device, ven_str, dev_str, freq / 1000,
+ dev->address, dev->address + (dev->mask-1),
+ dev->irq, dev->ver);
}
-void ambapp_print_ahb(ahbctrl_pp_dev * ahb, int index)
+void ambapp_print_ahb(ambapp_ahbdev *dev, int index)
{
- char *dev_str, *ven_str;
- int irq, ver, vendor, deviceid;
- unsigned int addr, mask;
- int j;
-
- vendor = amba_vendor(ahb->conf);
- deviceid = amba_device(ahb->conf);
- irq = amba_irq(ahb->conf);
- ver = amba_ver(ahb->conf);
+ char *dev_str, *ven_str, *type_str;
+ int i;
+ unsigned int freq;
- ven_str = ambapp_vendor_id2str(vendor);
+ ven_str = ambapp_vendor_id2str(dev->vendor);
if (!ven_str) {
ven_str = unknown;
dev_str = unknown;
} else {
- dev_str = ambapp_device_id2str(vendor, deviceid);
+ dev_str = ambapp_device_id2str(dev->vendor, dev->device);
if (!dev_str)
dev_str = unknown;
}
- printf("0x%02x:0x%02x:0x%02x: %s %s\n",
- index, vendor, deviceid, ven_str, dev_str);
+ /* Get Frequency of Core */
+ freq = ambapp_bus_freq(&ambapp_plb, dev->ahb_bus_index);
- for (j = 0; j < 4; j++) {
- addr = amba_membar_start(ahb->bars[j]);
- if (amba_membar_type(ahb->bars[j]) == 0)
+ printf("0x%02x:0x%02x:0x%02x: %s %s (%dkHz)\n",
+ index, dev->vendor, dev->device, ven_str, dev_str, freq / 1000);
+
+ for (i = 0; i < 4; i++) {
+ if ( dev->type[i] == 0 )
continue;
- if (amba_membar_type(ahb->bars[j]) == AMBA_TYPE_AHBIO)
- addr = AMBA_TYPE_AHBIO_ADDR(addr);
- mask = amba_membar_mask(ahb->bars[j]) << 20;
- printf(" mem: 0x%08x - 0x%08x\n", addr, addr + ((~mask) + 1));
+ type_str = ambapp_type_names[dev->type[i]];
+ printf(" %-7s: 0x%08x - 0x%08x\n", type_str, dev->address[i],
+ dev->address[i] + (dev->mask[i]-1));
}
- printf(" irq: %-2d (ver: %d)\n", irq, ver);
+ printf(" irq: %-2d (ver: %d)\n", dev->irq, dev->ver);
}
int do_ambapp_print(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
+ int index;
+ ambapp_apbdev apbdev;
+ ambapp_ahbdev ahbdev;
/* Print AHB Masters */
- puts("--------- AHB Masters ---------\n");
- ambapp_apb_print = 0;
- ambapp_ahb_print = 1;
- ambapp_ahbmst_count(99, 99); /* Get vendor&device 99 = nonexistent... */
+ puts("\n--------- AHB Masters ---------\n");
+ index = 0;
+ while ( ambapp_ahbmst_find(&ambapp_plb, 0, 0, index, &ahbdev) == 1 ) {
+ /* Found a AHB Master Device */
+ ambapp_print_ahb(&ahbdev, index);
+ index++;
+ }
/* Print AHB Slaves */
- puts("--------- AHB Slaves ---------\n");
- ambapp_ahbslv_count(99, 99); /* Get vendor&device 99 = nonexistent... */
+ puts("\n--------- AHB Slaves ---------\n");
+ index = 0;
+ while ( ambapp_ahbslv_find(&ambapp_plb, 0, 0, index, &ahbdev) == 1 ) {
+ /* Found a AHB Slave Device */
+ ambapp_print_ahb(&ahbdev, index);
+ index++;
+ }
/* Print APB Slaves */
- puts("--------- APB Slaves ---------\n");
- ambapp_apb_print = 1;
- ambapp_ahb_print = 0;
- ambapp_apb_count(99, 99); /* Get vendor&device 99 = nonexistent... */
-
- /* Reset, no futher printing */
- ambapp_apb_print = 0;
- ambapp_ahb_print = 0;
+ puts("\n--------- APB Slaves ---------\n");
+ index = 0;
+ while ( ambapp_apb_find(&ambapp_plb, 0, 0, index, &apbdev) == 1 ) {
+ /* Found a APB Slave Device */
+ ambapp_print_apb(&apbdev, index);
+ index++;
+ }
+
puts("\n");
return 0;
}
@@ -256,16 +571,19 @@ int ambapp_init_reloc(void)
while (vend->vendor_id && vend->name) {
vend->name = (char *)((unsigned int)vend->name + gd->reloc_off);
+ vend->desc = (char *)((unsigned int)vend->desc + gd->reloc_off);
vend->devices =
(ambapp_device_name *) ((unsigned int)vend->devices +
- gd->reloc_off);;
+ gd->reloc_off);
dev = vend->devices;
vend++;
if (!dev)
continue;
while (dev->device_id && dev->name) {
dev->name =
- (char *)((unsigned int)dev->name + gd->reloc_off);;
+ (char *)((unsigned int)dev->name + gd->reloc_off);
+ dev->desc =
+ (char *)((unsigned int)dev->desc + gd->reloc_off);
dev++;
}
}
diff --git a/cpu/leon3/Makefile b/cpu/leon3/Makefile
index 182543d..d8f89bc 100644
--- a/cpu/leon3/Makefile
+++ b/cpu/leon3/Makefile
@@ -26,7 +26,7 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(CPU).a
START = start.o
-SOBJS =
+SOBJS = ambapp_low.o ambapp_low_c.o
COBJS = cpu_init.o serial.o cpu.o ambapp.o interrupts.o prom.o usb_uhci.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
diff --git a/cpu/leon3/ambapp.c b/cpu/leon3/ambapp.c
index efd41ae..d332294 100644
--- a/cpu/leon3/ambapp.c
+++ b/cpu/leon3/ambapp.c
@@ -1,9 +1,8 @@
-/* Gaisler AMBA Plug&Play bus scanning. Functions
- * ending on _nomem is inteded to be used only during
- * initialization, only registers are used (no ram).
+/* GRLIB AMBA Plug&Play information scanning, relies on assembler
+ * routines.
*
- * (C) Copyright 2007
- * Daniel Hellstrom, Gaisler Research, daniel at gaisler.com
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -22,338 +21,348 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
+ *
*/
+/* #define DEBUG */
+
#include <common.h>
-#include <command.h>
#include <ambapp.h>
+#include <config.h>
+
+/************ C INTERFACE OF ASSEMBLER SCAN ROUTINES ************/
+struct ambapp_find_apb_info {
+ /* Address of APB device Plug&Play information */
+ struct ambapp_pnp_apb *pnp;
+ /* AHB Bus index of where the APB-Master Bridge device was found */
+ int ahb_bus_index;
+ int dec_index;
+};
-#if defined(CONFIG_CMD_AMBAPP)
-extern void ambapp_print_apb(apbctrl_pp_dev * apb,
- ambapp_ahbdev * apbmst, int index);
-extern void ambapp_print_ahb(ahbctrl_pp_dev * ahb, int index);
-extern int ambapp_apb_print;
-extern int ambapp_ahb_print;
-#endif
+struct ambapp_find_ahb_info {
+ /* Address of AHB device Plug&Play information */
+ struct ambapp_pnp_ahb *pnp;
+ /* AHB Bus index of where the AHB device was found */
+ int ahb_bus_index;
+ int dec_index;
+};
-static int ambapp_apb_scan(unsigned int vendor, /* Plug&Play Vendor ID */
- unsigned int driver, /* Plug&Play Device ID */
- ambapp_apbdev * dev, /* Result(s) is placed here */
- int index, /* Index of device to start copying Plug&Play
- * info into dev
- */
- int max_cnt /* Maximal count that dev can hold, if dev
- * is NULL function will stop scanning after
- * max_cnt devices are found.
- */
- )
+extern void ambapp_find_buses(
+ unsigned int ioarea,
+ struct ambapp_bus *abus
+ );
+
+extern int ambapp_find_apb(
+ struct ambapp_bus *abus,
+ unsigned int dev_vend,
+ int index,
+ struct ambapp_find_apb_info *result
+ );
+
+extern int ambapp_find_ahb(
+ struct ambapp_bus *abus,
+ unsigned int dev_vend,
+ int index,
+ int type,
+ struct ambapp_find_ahb_info *result
+ );
+
+/************ C ROUTINES USED BY U-BOOT AMBA CORE DRIVERS ************/
+struct ambapp_bus ambapp_plb;
+
+void ambapp_bus_init(
+ unsigned int ioarea,
+ unsigned int freq,
+ struct ambapp_bus *abus)
{
- int i, cnt = 0;
- unsigned int apbmst_base;
- ambapp_ahbdev apbmst;
- apbctrl_pp_dev *apb;
-
- if (max_cnt == 0)
- return 0;
-
- /* Get AMBA APB Master */
- if (ambapp_ahbslv_first(VENDOR_GAISLER, GAISLER_APBMST, &apbmst) != 1) {
- return 0;
- }
-
- /* Get APB CTRL Plug&Play info area */
- apbmst_base = apbmst.address[0] & LEON3_IO_AREA;
- apb = (apbctrl_pp_dev *) (apbmst_base | LEON3_CONF_AREA);
+ int i;
+
+ ambapp_find_buses(ioarea, abus);
+ for(i=0; i<6; i++)
+ if ( abus->ioareas[i] == 0 )
+ break;
+ abus->buses = i;
+ abus->freq = freq;
+}
- for (i = 0; i < LEON3_APB_SLAVES; i++) {
-#if defined(CONFIG_CMD_AMBAPP)
- if (ambapp_apb_print && amba_vendor(apb->conf)
- && amba_device(apb->conf)) {
- ambapp_print_apb(apb, &apbmst, i);
- }
-#endif
- if ((amba_vendor(apb->conf) == vendor) &&
- (amba_device(apb->conf) == driver) && ((index < 0)
- || (index-- == 0))) {
- /* Convert Plug&Play info into a more readable format */
- cnt++;
- if (dev) {
- dev->irq = amba_irq(apb->conf);
- dev->ver = amba_ver(apb->conf);
- dev->address =
- (apbmst_base |
- (((apb->
- bar & 0xfff00000) >> 12))) & (((apb->
- bar &
- 0x0000fff0)
- << 4) |
- 0xfff00000);
- dev++;
- }
- /* found max devices? */
- if (cnt >= max_cnt)
- return cnt;
- }
- /* Get next Plug&Play entry */
- apb++;
- }
- return cnt;
+/* Parse APB PnP Information */
+void ambapp_apb_parse(struct ambapp_find_apb_info *info, ambapp_apbdev *dev)
+{
+ struct ambapp_pnp_apb *apb = info->pnp;
+ unsigned int apbbase = (unsigned int)apb & 0xfff00000;
+
+ dev->vendor = amba_vendor(apb->id);
+ dev->device = amba_device(apb->id);
+ dev->irq = amba_irq(apb->id);
+ dev->ver = amba_ver(apb->id);
+ dev->address = (apbbase | (((apb->iobar & 0xfff00000) >> 12))) &
+ (((apb->iobar & 0x0000fff0) << 4) | 0xfff00000);
+ dev->mask = amba_apb_mask(apb->iobar);
+ dev->ahb_bus_index = info->ahb_bus_index - 1;
}
-unsigned int ambapp_apb_next_nomem(register unsigned int vendor, /* Plug&Play Vendor ID */
- register unsigned int driver, /* Plug&Play Device ID */
- register int index)
+/* Parse AHB PnP information */
+void ambapp_ahb_parse(struct ambapp_find_ahb_info *info, ambapp_ahbdev *dev)
{
- register int i;
- register ahbctrl_pp_dev *apbmst;
- register apbctrl_pp_dev *apb;
- register unsigned int apbmst_base;
-
- /* APBMST is a AHB Slave */
- apbmst = ambapp_ahb_next_nomem(VENDOR_GAISLER, GAISLER_APBMST, 1, 0);
- if (!apbmst)
- return 0;
-
- apbmst_base = amba_membar_start(apbmst->bars[0]);
- if (amba_membar_type(apbmst->bars[0]) == AMBA_TYPE_AHBIO)
- apbmst_base = AMBA_TYPE_AHBIO_ADDR(apbmst_base);
- apbmst_base &= LEON3_IO_AREA;
-
- /* Find the vendor/driver device on the first APB bus */
- apb = (apbctrl_pp_dev *) (apbmst_base | LEON3_CONF_AREA);
-
- for (i = 0; i < LEON3_APB_SLAVES; i++) {
- if ((amba_vendor(apb->conf) == vendor) &&
- (amba_device(apb->conf) == driver) && ((index < 0)
- || (index-- == 0))) {
- /* Convert Plug&Play info info a more readable format */
- return (apbmst_base | (((apb->bar & 0xfff00000) >> 12)))
- & (((apb->bar & 0x0000fff0) << 4) | 0xfff00000);
+ struct ambapp_pnp_ahb *ahb = info->pnp;
+ unsigned int ahbbase = (unsigned int)ahb & 0xfff00000;
+ int i, type;
+ unsigned int addr, mask, mbar;
+
+ dev->vendor = amba_vendor(ahb->id);
+ dev->device = amba_device(ahb->id);
+ dev->irq = amba_irq(ahb->id);
+ dev->ver = amba_ver(ahb->id);
+ dev->userdef[0] = ahb->custom[0];
+ dev->userdef[1] = ahb->custom[1];
+ dev->userdef[2] = ahb->custom[2];
+ dev->ahb_bus_index = info->ahb_bus_index - 1;
+ for (i=0; i<4; i++) {
+ mbar = ahb->mbar[i];
+ addr = amba_membar_start(mbar);
+ type = amba_membar_type(mbar);
+ if ( type == AMBA_TYPE_AHBIO ) {
+ addr = amba_ahbio_adr(addr, ahbbase);
+ mask = (((unsigned int)
+ (amba_membar_mask((~mbar))<<8)|0xff))+1;
+ } else {
+ /* AHB memory area, absolute address */
+ mask = (~((unsigned int)
+ (amba_membar_mask(mbar)<<20)))+1;
}
- /* Get next Plug&Play entry */
- apb++;
+ dev->address[i] = addr;
+ dev->mask[i] = mask;
+ dev->type[i] = type;
}
- return 0;
}
-/****************************** APB SLAVES ******************************/
-
-int ambapp_apb_count(unsigned int vendor, unsigned int driver)
+int ambapp_apb_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_apbdev *dev)
{
- return ambapp_apb_scan(vendor, driver, NULL, 0, LEON3_APB_SLAVES);
-}
+ unsigned int devid = AMBA_PNP_ID(vendor, device);
+ int found;
+ struct ambapp_find_apb_info apbdev;
-int ambapp_apb_first(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev)
-{
- return ambapp_apb_scan(vendor, driver, dev, 0, 1);
+ found = ambapp_find_apb(abus, devid, index, &apbdev);
+ if ( found == 1 ) {
+ ambapp_apb_parse(&apbdev, dev);
+ }
+ return found;
}
-int ambapp_apb_next(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev, int index)
+int ambapp_apb_count(struct ambapp_bus *abus, int vendor, int device)
{
- return ambapp_apb_scan(vendor, driver, dev, index, 1);
-}
+ unsigned int devid = AMBA_PNP_ID(vendor, device);
+ int found;
+ struct ambapp_find_apb_info apbdev;
-int ambapp_apbs_first(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev, int max_cnt)
-{
- return ambapp_apb_scan(vendor, driver, dev, 0, max_cnt);
+ found = ambapp_find_apb(abus, devid, 63, &apbdev);
+ if ( found == 1 ) {
+ return 64;
+ } else {
+ return 63 - apbdev.dec_index;
+ }
}
-enum {
- AHB_SCAN_MASTER = 0,
- AHB_SCAN_SLAVE = 1
-};
-
-/* Scan AMBA Plug&Play bus for AMBA AHB Masters or AHB Slaves
- * for a certain matching Vendor and Device ID.
- *
- * Return number of devices found.
- *
- * Compact edition...
- */
-static int ambapp_ahb_scan(unsigned int vendor, /* Plug&Play Vendor ID */
- unsigned int driver, /* Plug&Play Device ID */
- ambapp_ahbdev * dev, /* Result(s) is placed here */
- int index, /* Index of device to start copying Plug&Play
- * info into dev
- */
- int max_cnt, /* Maximal count that dev can hold, if dev
- * is NULL function will stop scanning after
- * max_cnt devices are found.
- */
- int type /* Selectes what type of devices to scan.
- * 0=AHB Masters
- * 1=AHB Slaves
- */
- )
+int ambapp_ahb_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_ahbdev *dev,
+ int type
+ )
{
- int i, j, cnt = 0, max_pp_devs;
- unsigned int addr;
- ahbctrl_info *info = (ahbctrl_info *) (LEON3_IO_AREA | LEON3_CONF_AREA);
- ahbctrl_pp_dev *ahb;
-
- if (max_cnt == 0)
- return 0;
-
- if (type == 0) {
- max_pp_devs = LEON3_AHB_MASTERS;
- ahb = info->masters;
- } else {
- max_pp_devs = LEON3_AHB_SLAVES;
- ahb = info->slaves;
- }
+ int found;
+ struct ambapp_find_ahb_info ahbdev;
+ unsigned int devid = AMBA_PNP_ID(vendor, device);
- for (i = 0; i < max_pp_devs; i++) {
-#if defined(CONFIG_CMD_AMBAPP)
- if (ambapp_ahb_print && amba_vendor(ahb->conf) &&
- amba_device(ahb->conf)) {
- ambapp_print_ahb(ahb, i);
- }
-#endif
- if ((amba_vendor(ahb->conf) == vendor) &&
- (amba_device(ahb->conf) == driver) &&
- ((index < 0) || (index-- == 0))) {
- /* Convert Plug&Play info info a more readable format */
- cnt++;
- if (dev) {
- dev->irq = amba_irq(ahb->conf);
- dev->ver = amba_ver(ahb->conf);
- dev->userdef[0] = ahb->userdef[0];
- dev->userdef[1] = ahb->userdef[1];
- dev->userdef[2] = ahb->userdef[2];
- for (j = 0; j < 4; j++) {
- addr = amba_membar_start(ahb->bars[j]);
- if (amba_membar_type(ahb->bars[j]) ==
- AMBA_TYPE_AHBIO)
- addr =
- AMBA_TYPE_AHBIO_ADDR(addr);
- dev->address[j] = addr;
- }
- dev++;
- }
- /* found max devices? */
- if (cnt >= max_cnt)
- return cnt;
- }
- /* Get next Plug&Play entry */
- ahb++;
+ found = ambapp_find_ahb(abus, devid, index, type, &ahbdev);
+ if ( found == 1 ) {
+ ambapp_ahb_parse(&ahbdev, dev);
}
- return cnt;
+ return found;
}
-unsigned int ambapp_ahb_get_info(ahbctrl_pp_dev * ahb, int info)
+int ambapp_ahbmst_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_ahbdev *dev)
{
- register unsigned int ret;
-
- if (!ahb)
- return 0;
-
- switch (info) {
- default:
- info = 0;
- case 0:
- case 1:
- case 2:
- case 3:
- /* Get Address from PnP Info */
- ret = amba_membar_start(ahb->bars[info]);
- if (amba_membar_type(ahb->bars[info]) == AMBA_TYPE_AHBIO)
- ret = AMBA_TYPE_AHBIO_ADDR(ret);
- return ret;
- }
- return 0;
+ return ambapp_ahb_find(abus, vendor, device, index, dev, DEV_AHB_MST);
+}
+int ambapp_ahbslv_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_ahbdev *dev)
+{
+ return ambapp_ahb_find(abus, vendor, device, index, dev, DEV_AHB_SLV);
}
-ahbctrl_pp_dev *ambapp_ahb_next_nomem(register unsigned int vendor, /* Plug&Play Vendor ID */
- register unsigned int driver, /* Plug&Play Device ID */
- register unsigned int opts, /* 1=slave, 0=master */
- register int index)
+int ambapp_ahb_count(struct ambapp_bus *abus, int vendor, int device, int type)
{
- register ahbctrl_pp_dev *ahb;
- register ahbctrl_info *info =
- (ahbctrl_info *) (LEON3_IO_AREA | LEON3_CONF_AREA);
- register int i;
- register int max_pp_devs;
-
- if (opts == 0) {
- max_pp_devs = LEON3_AHB_MASTERS;
- ahb = info->masters;
- } else {
- max_pp_devs = LEON3_AHB_SLAVES;
- ahb = info->slaves;
- }
+ int found;
+ struct ambapp_find_ahb_info ahbdev;
+ unsigned int devid = AMBA_PNP_ID(vendor, device);
- for (i = 0; i < max_pp_devs; i++) {
- if ((amba_vendor(ahb->conf) == vendor) &&
- (amba_device(ahb->conf) == driver) &&
- ((index < 0) || (index-- == 0))) {
- /* Convert Plug&Play info info a more readable format */
- return ahb;
- }
- /* Get next Plug&Play entry */
- ahb++;
+ found = ambapp_find_ahb(abus, devid, 63, type, &ahbdev);
+ if ( found == 1 ) {
+ return 64;
+ } else {
+ return 63 - ahbdev.dec_index;
}
- return 0;
}
-/****************************** AHB MASTERS ******************************/
-int ambapp_ahbmst_count(unsigned int vendor, unsigned int driver)
+int ambapp_ahbmst_count(struct ambapp_bus *abus, int vendor, int device)
{
- /* Get number of devices of this vendor&device ID */
- return ambapp_ahb_scan(vendor, driver, NULL, 0, LEON3_AHB_MASTERS,
- AHB_SCAN_MASTER);
+ return ambapp_ahb_count(abus, vendor, device, DEV_AHB_MST);
}
-int ambapp_ahbmst_first(unsigned int vendor, unsigned int driver,
- ambapp_ahbdev * dev)
+int ambapp_ahbslv_count(struct ambapp_bus *abus, int vendor, int device)
{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, 0, 1, AHB_SCAN_MASTER);
+ return ambapp_ahb_count(abus, vendor, device, DEV_AHB_SLV);
}
-int ambapp_ahbmst_next(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int index)
-{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, index, 1, AHB_SCAN_MASTER);
-}
+/* The define CONFIG_SYS_GRLIB_SINGLE_BUS may be defined on GRLIB systems
+ * where only one AHB Bus is available - no bridges are present. This option
+ * is available only to reduce the footprint.
+ *
+ * Defining this on a multi-bus GRLIB system may also work depending on the
+ * design.
+ */
-int ambapp_ahbmsts_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int max_cnt)
-{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, 0, max_cnt,
- AHB_SCAN_MASTER);
-}
+#ifndef CONFIG_SYS_GRLIB_SINGLE_BUS
-/****************************** AHB SLAVES ******************************/
-int ambapp_ahbslv_count(unsigned int vendor, unsigned int driver)
-{
- /* Get number of devices of this vendor&device ID */
- return ambapp_ahb_scan(vendor, driver, NULL, 0, LEON3_AHB_SLAVES,
- AHB_SCAN_SLAVE);
-}
+/* GAISLER AHB2AHB Version 1 Bridge Definitions */
+#define AHB2AHB_V1_FLAG_FFACT 0x0f0 /* Frequency factor against top bus */
+#define AHB2AHB_V1_FLAG_FFACT_DIR 0x100 /* Factor direction, 0=down, 1=up */
+#define AHB2AHB_V1_FLAG_MBUS 0x00c /* Master bus number mask */
+#define AHB2AHB_V1_FLAG_SBUS 0x003 /* Slave bus number mask */
-int ambapp_ahbslv_first(unsigned int vendor, unsigned int driver,
- ambapp_ahbdev * dev)
+/* Get Parent bus frequency. Note that since we go from a "child" bus
+ * to a parent bus, the frequency factor direction is inverted.
+ */
+unsigned int gaisler_ahb2ahb_v1_freq(ambapp_ahbdev *ahb, unsigned int freq)
{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, 0, 1, AHB_SCAN_SLAVE);
+ int dir;
+ unsigned char ffact;
+
+ /* Get division/multiple factor */
+ ffact = (ahb->userdef[0] & AHB2AHB_V1_FLAG_FFACT) >> 4;
+ if ( ffact != 0 ) {
+ dir = ahb->userdef[0] & AHB2AHB_V1_FLAG_FFACT_DIR;
+
+ /* Calculate frequency by dividing or
+ * multiplying system frequency
+ */
+ if ( dir ) {
+ freq = freq * ffact;
+ } else {
+ freq = freq / ffact;
+ }
+ }
+
+ return freq;
}
-int ambapp_ahbslv_next(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int index)
+/* AHB2AHB and L2CACHE ver 2 is not supported yet. */
+unsigned int gaisler_ahb2ahb_v2_freq(ambapp_ahbdev *ahb, unsigned int freq)
{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, index, 1, AHB_SCAN_SLAVE);
+ printf("gaisler_ahb2ahb_v2_freq: AHB2AHB ver 2 not supported\n");
+ while(1) ;
}
+#endif
-int ambapp_ahbslvs_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int max_cnt)
+/* Return the frequency of a AHB bus identified by index found
+ * note that this is not the AHB Bus number.
+ */
+unsigned int ambapp_bus_freq (
+ struct ambapp_bus *abus,
+ int ahb_bus_index
+ )
{
- /* find first device of this */
- return ambapp_ahb_scan(vendor, driver, dev, 0, max_cnt, AHB_SCAN_SLAVE);
+ unsigned int freq = abus->freq;
+#ifndef CONFIG_SYS_GRLIB_SINGLE_BUS
+ unsigned int ioarea, ioarea_parent, bridge_pnp_ofs;
+ struct ambapp_find_ahb_info ahbinfo;
+ ambapp_ahbdev ahb;
+ int parent;
+
+ debug("ambapp_bus_freq: get freq on bus %d\n", ahb_bus_index);
+
+ while ( ahb_bus_index != 0) {
+
+ debug(" BUS[0]: 0x%08x\n", abus->ioareas[0]);
+ debug(" BUS[1]: 0x%08x\n", abus->ioareas[1]);
+ debug(" BUS[2]: 0x%08x\n", abus->ioareas[2]);
+ debug(" BUS[3]: 0x%08x\n", abus->ioareas[3]);
+ debug(" BUS[4]: 0x%08x\n", abus->ioareas[4]);
+ debug(" BUS[5]: 0x%08x\n", abus->ioareas[5]);
+
+ /* Get I/O area of AHB bus */
+ ioarea = abus->ioareas[ahb_bus_index];
+
+ printf(" IOAREA: 0x%08x\n", ioarea);
+
+ /* Get parent bus */
+ parent = (ioarea & 0x7);
+ if ( parent == 0 ) {
+ printf("ambapp_bus_freq: parent=0 indicates no parent! Stopping.\n");
+ while(1) ;
+ }
+ parent = parent - 1;
+ bridge_pnp_ofs = ioarea & 0x7e0;
+
+ debug(" PARENT: %d\n", parent);
+ debug(" BRIDGE_OFS: 0x%08x\n", bridge_pnp_ofs);
+
+ /* Get AHB/AHB bridge PnP address */
+ ioarea_parent = (abus->ioareas[parent] & 0xfff00000) |
+ AMBA_CONF_AREA | AMBA_AHB_SLAVE_CONF_AREA;
+ ahbinfo.pnp = (struct ambapp_pnp_ahb *)
+ (ioarea_parent | bridge_pnp_ofs);
+
+ debug(" IOAREA PARENT: 0x%08x\n", ioarea_parent);
+ debug(" BRIDGE PNP: 0x%08x\n", ahbinfo.pnp);
+
+ /* Parse the AHB information */
+ ahbinfo.ahb_bus_index = parent;
+ ambapp_ahb_parse(&ahbinfo, &ahb);
+
+ debug(" BRIDGE ID: VENDOR=%d(0x%x), DEVICE=%d(0x%x)\n",
+ ahb.vendor, ahb.vendor, ahb.device, ahb.device);
+
+ /* Different bridges may convert frequency differently */
+ if ( (ahb.vendor == VENDOR_GAISLER) &&
+ ((ahb.device == GAISLER_AHB2AHB) ||
+ (ahb.device == GAISLER_L2CACHE)) ) {
+ /* Get new frequency */
+ if ( ahb.ver > 1 ) {
+ freq = gaisler_ahb2ahb_v2_freq(&ahb, freq);
+ } else {
+ freq = gaisler_ahb2ahb_v1_freq(&ahb, freq);
+ }
+ debug(" NEW FREQ: %dHz\n", freq);
+ } else {
+ printf("ambapp_bus_freq: unsupported AMBA bridge\n");
+ while(1) ;
+ }
+
+ /* Step upwards towards system top bus */
+ ahb_bus_index = parent;
+ }
+#endif
+
+ debug("ambapp_bus_freq: %dHz\n", freq);
+
+ return freq;
}
diff --git a/cpu/leon3/ambapp_low.S b/cpu/leon3/ambapp_low.S
new file mode 100644
index 0000000..bbf2d01
--- /dev/null
+++ b/cpu/leon3/ambapp_low.S
@@ -0,0 +1,798 @@
+/* GRLIB AMBA Plug&Play information scanning implemented without
+ * using memory (stack) and one register window. The code scan
+ * the PnP info and inserts the AHB bridges/buses into register
+ * i0-i5.
+ * The code support
+ * - up to 6 AHB buses
+ * - multiple APB buses
+ * - support for AHB2AHB & L2CACHE bridges
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <ambapp.h>
+
+ .seg "text"
+ .globl _nomem_amba_init
+ .globl _nomem_ambapp_find_buses
+ .globl _nomem_find_apb
+ .globl _nomem_find_ahb
+
+/* Overview
+ * ========
+ *
+ * _nomem_amba_init - Init AMBA bus and calls _nomem_ambapp_find_buses
+ * _nomem_ambapp_find_buses - Scan AMBA PnP info for AHB buses/bridges and
+ * place them in i0-i5, see below
+ * _nomem_find_apb - Find one APB device identified by VENDOR:DEVICE
+ * ID and an index.
+ * _nomem_find_ahb - Find one AHB Master or Slave device identified
+ * by VENDOR:DEVICE ID and an index.
+ * init_ahb_bridges - Local function. Clears i0-i5
+ * insert_ahb_bridge - Local function. Insert a new AHB bus into first
+ * free register in i0-i5. It also checks that the
+ * bus has not already been added.
+ * get_ahb_bridge - Local function. Get AHB bus from registers,
+ * return register iN, where N is defined by o0.
+ *
+ * The _nomem_find_apb and _nomem_find_ahb function requires that i0-i5
+ * are populated with the AHB buses of the system. The registers are
+ * initialized by _nomem_ambapp_find_buses.
+ *
+ * AHB Bus result and requirements of i0-i5
+ * ========================================
+ *
+ * i0: AHB BUS0 IOAREA, no parent bus
+ * i1: AHB BUS1 IOAREA, parent bus is always i0 (AHB BUS0) and bridge address
+ * i2: AHB BUS2 IOAREA, 3-bit parent bus number and bridge address
+ * i3: AHB BUS3 IOAREA, 3-bit parent bus number and bridge address
+ * i4: AHB BUS4 IOAREA, 3-bit parent bus number and bridge address
+ * i5: AHB BUS5 IOAREA, 3-bit parent bus number and bridge address
+ *
+ * AHB BUS
+ * -------
+ * Bits 31-20 (0xfff00000) contain the found bus I/O Area (AHB PnP area).
+ *
+ * 3-bit Parent bus
+ * ----------------
+ * Bits 2-0 (0x00000007) contain parent bus number. Zero if no parent
+ * bus, 1 = parent is AHB BUS 0 (i0), 2 = parent is AHB BUS 1 (i1)..
+ *
+ * Bridge Address
+ * --------------
+ * Bits 10-5 (0x000007e0) contain the index of the Bridge's PnP
+ * information on the parent. Since all bridges are found in the
+ * PnP information they all have a PnP entry. Together with the
+ * parent bus number the PnP entry can be found:
+ * PnPEntry = (BRIDGE_ADDRESS + (iN & 0xfff00000)) | 0x000ff800
+ * where N is the parent bus minus one.
+ *
+ */
+
+/* Function initializes the AHB Bridge I/O AREA storage. (Clears i0-i5)
+ *
+ * Arguments
+ * none
+ *
+ * Results
+ * none
+ *
+ * Clobbered
+ * none
+ */
+
+init_ahb_bridges:
+ mov %g0, %i0
+ mov %g0, %i1
+ mov %g0, %i2
+ mov %g0, %i3
+ mov %g0, %i4
+ retl
+ mov %g0, %i5
+
+/* Function returns AHB Bridge I/O AREA for specified bus.
+ *
+ * Arguments
+ * - o0 = bus number
+ *
+ * Results
+ * - o0 = I/O AREA
+ *
+ * Clobbered
+ * none
+ */
+get_ahb_bridge:
+ cmp %o0, 1
+ be,a L1
+ mov %i0, %o0
+
+ cmp %o0, 2
+ be,a L1
+ mov %i1, %o0
+
+ cmp %o0, 3
+ be,a L1
+ mov %i2, %o0
+
+ cmp %o0, 4
+ be,a L1
+ mov %i3, %o0
+
+ cmp %o0, 5
+ be,a L1
+ mov %i4, %o0
+
+ cmp %o0, 6
+ be,a L1
+ mov %i5, %o0
+
+ /* o0 > 6: only 6 buses supported */
+ mov %g0, %o0
+L1:
+ retl
+ nop
+
+/* Function adds a AHB Bridge I/O AREA to the i0-i5 registers if
+ * not already added. It stores the bus PnP start information.
+ *
+ * Arguments
+ * - o0 = AHB Bridge I/O area
+ *
+ * Results
+ * none
+ *
+ * Clobbered
+ * o2, o3
+ */
+insert_ahb_bridge:
+ /* Check that bridge hasn't already been added */
+ andn %o0, 0x7ff, %o2
+ andn %i0, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+ andn %i1, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+ andn %i2, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+ andn %i3, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+ andn %i4, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+ andn %i5, 0x7ff, %o3
+ cmp %o3, %o2
+ be L2
+
+ /* Insert into first free posistion */
+ cmp %i0, %g0
+ be,a L2
+ mov %o0, %i0
+
+ cmp %i1, %g0
+ be,a L2
+ mov %o0, %i1
+
+ cmp %i2, %g0
+ be,a L2
+ mov %o0, %i2
+
+ cmp %i3, %g0
+ be,a L2
+ mov %o0, %i3
+
+ cmp %i4, %g0
+ be,a L2
+ mov %o0, %i4
+
+ cmp %i5, %g0
+ be,a L2
+ mov %o0, %i5
+L2:
+ retl
+ nop
+
+/* FUNCTION int _nomem_find_ahb_bus(
+ * unsigned int bridge,
+ * int vendor_device,
+ * int index,
+ * void **pconf,
+ * int not_used,
+ * int option
+ * )
+ *
+ * Scans the AHB Master or Slave area for a matching VENDOR:DEVICE, the
+ * index is decremented when a matching device is found but index is
+ * greater than zero. When index is zero and a matching DEVICE:VENDOR
+ * is found the AHB configuration address and AHB I/O area is returned.
+ *
+ * i0-i7,l0,l1,l2,l3,l4,g2,o6 is not available for use.
+ * o1,o5 Must be left untouched
+ *
+ * Results
+ * - o0 Number of found devices (1 or 0)
+ * - o2 is decremented for each matching VENDOR:DEVICE found, zero if found
+ * - o3 Address of the AHB PnP configuration entry (Only valid if o0=1)
+ *
+ * Clobbered
+ * - o3 (Clobbered when no device was found)
+ * - o4 (Number of Devices left to search)
+ * - o0 (Bus ID, PnP ID, Device)
+ */
+_nomem_find_ahb_bus:
+
+ /* Get number of Slaves/Masters. Only AHB Bus 0 has 64 AHB Masters/Slaves
+ * the other AHB buses has 16 slaves and 16 masters.
+ */
+ add %g0, 16, %o4 /* Defaulting to 16 */
+ andcc %o0, 0x7, %g0 /* 3-bit bus id */
+ be,a .L_maxloops_detected
+ add %g0, 64, %o4 /* AHB Bus 0 has 64 AHB Masters and Slaves */
+.L_maxloops_detected:
+
+ /* Get start address of AHB Slave or AHB Master area depending on what
+ * we are searching for.
+ */
+ andn %o0, 0x7ff, %o0 /* Remove Bus ID and 5-bit AHB/AHB Bridge PnP Address to get I/O Area */
+ set AMBA_CONF_AREA, %o3
+ or %o3, %o0, %o3 /* Master area address */
+
+ cmp %o5, DEV_AHB_SLV
+ be,a .L_conf_area_calculated
+ or %o3, AMBA_AHB_SLAVE_CONF_AREA, %o3 /* Add 0x800 to get to slave area */
+.L_conf_area_calculated:
+
+ /* Iterate over all AHB device and try to find matching DEVICE:VENDOR
+ * o1 - VENDOR|DEVICE
+ * o2 - Index
+ * o3 - Current AHB Device Configuration address
+ * o5 - Type (leave untouched)
+ *
+ * o4 - Number of AHB device left to process
+ * o0 - tmp
+ */
+.L_process_one_conf:
+ ld [%o3], %o0
+ andn %o0, 0xfff, %o0
+ cmp %o0, 0 /* No device if zero */
+ beq .L_next_conf
+ cmp %o1, 0 /* If VENDOR:DEVICE==0, consider all matching */
+ beq .L_process_ahb_dev_found
+ cmp %o0, %o1 /* Does VENDOR and DEVICE Match? */
+ bne .L_next_conf
+ nop
+.L_process_ahb_dev_found:
+ /* Found a Matching VENDOR:DEVICE, index must also match */
+ cmp %o2, %g0
+ bne .L_next_conf
+ dec %o2
+ /* Index matches also, return happy with o3 set to AHB Conf Address */
+ mov %g0, %o2
+ retl
+ add %g0, 1, %o0
+
+.L_next_conf:
+ subcc %o4, 1, %o4 /* One device has been processed, Are there more devices to process? */
+ bne .L_process_one_conf
+ add %o3, AMBA_AHB_CONF_LENGH, %o3 /* Next Configuration entry */
+ /* No Matching device found */
+ retl
+ mov %g0, %o0
+
+/* FUNCTION int _nomem_find_ahb(
+ * int unused,
+ * int vendor_device,
+ * int index,
+ * void **pconf,
+ * int *ahb_bus_index,
+ * int option,
+ * )
+ *
+ * Find a AHB Master or AHB Slave device, it puts the address of the AHB PnP
+ * configuration in o3 (pconf), the I/O Area base address in o4 (pioarea).
+ *
+ * Calls _nomem_find_ahb_bus for every AHB bus.
+ *
+ * i0-i7, l0, l1, o6, g1, g4-g7 is not available for use.
+ *
+ * Arguments
+ * - o0 Unused
+ *
+ * Results
+ * - o0 Number of found devices (1 or 0)
+ * - o2 Decremented Index (Zero if found)
+ * - o3 Address of the AHB PnP configuration entry
+ * - o4 AHB Bus index the device was found on (if o0=1)
+ * - o5 Left untouched
+ *
+ * Clobbered
+ * - o0 (AHB Bridge and used by _nomem_find_ahb_bus)
+ * - o2 (index is decremented)
+ * - l2 (Current AHB Bus index)
+ * - g2 (return address)
+ */
+_nomem_find_ahb:
+ mov %o7, %g2 /* Save return address */
+ /* Scan all AHB Buses found for the AHB Master/Slave matching VENDOR:DEVICE */
+ clr %l2
+.L_search_next_ahb_bus:
+ add %l2, 1, %l2
+ call get_ahb_bridge /* Get bus %l0 I/O Area */
+ mov %l2, %o0
+ cmp %o0, %g0
+ be .L_no_device_found /* If no more AHB bus is left to be scanned, proceed */
+ nop
+ call _nomem_find_ahb_bus /* Scan AHB bus %o0 for VENDOR:DEVICE. Index in o3 is decremented */
+ nop
+ cmp %o0, %g0 /* If VENDOR:DEVICE was not found scan next AHB Bus */
+ be .L_search_next_ahb_bus /* Do next bus is o0=0 (not found) */
+ nop
+ /* The device was found, o0 is 1 */
+ mov %g2, %o7 /* Restore return address */
+ retl
+ mov %l2, %o4 /* The AHB bus index the device was found on */
+
+ /* No device found matching */
+.L_no_device_found:
+ mov %g2, %o7 /* Restore return address */
+ retl
+ mov %g0, %o0
+
+
+/* FUNCTION int _nomem_find_apb_bus(
+ * int apbmst,
+ * int vendor_device,
+ * int index,
+ * void **pconf
+ * )
+ *
+ * Find a APB Slave device, it puts the address of the APB PnP configuration
+ * in o3 (pconf).
+ *
+ * Calls _nomem_find_ahb_bus for every AHB bus searching for AHB/APB Bridges.
+ * The AHB/APB bridges are AHB Slaves with ID GAISLER_APBMST.
+ *
+ * Results
+ * - o0 Number of found devices (1 or 0)
+ * - o2 Decremented Index
+ * - o3 Address of the found APB device PnP configuration entry
+ *
+ * Clobbered
+ * - o5 PnP VENDOR:DEVICE ID
+ */
+
+_nomem_find_apb_bus:
+ set AMBA_CONF_AREA, %o3
+ or %o0, %o3, %o3 /* Calc start of APB device PnP info */
+ add %g0, 16, %o0 /* o0, number of APB Slaves left to scan */
+.L_process_one_apb_conf:
+ ld [%o3], %o5
+ andn %o5, 0xfff, %o5
+ cmp %o5, 0 /* No device if zero */
+ beq .L_process_apb_dev_not_found
+ cmp %o1, 0 /* If VENDOR:DEVICE == -1, consider all matching */
+ beq .L_process_apb_dev_found
+ cmp %o1, %o5 /* Found VENDOR:DEVICE */
+ bne .L_process_apb_dev_not_found
+ nop
+
+.L_process_apb_dev_found:
+ /* Found matching device, compare index */
+ cmp %o2, %g0
+ bne .L_process_apb_dev_not_found
+ dec %o2
+ /* Matching index and VENDOR:DEVICE */
+ retl
+ add %g0, 1, %o0
+
+.L_process_apb_dev_not_found:
+ subcc %o0, 1, %o0
+ bne .L_process_one_apb_conf
+ add %o3, 8, %o3
+ retl
+ mov %g0, %o0
+
+/* FUNCTION int _nomem_find_apb(
+ * int unused,
+ * int vendor_device,
+ * int index,
+ * void **pconf,
+ * int *ahb_bus_index
+ * )
+ *
+ * Find a APB Slave device, it puts the address of the APB PnP configuration
+ * in o3 (pconf), the APB Master I/O Area base address in o4 (papbarea).
+ *
+ * Calls _nomem_find_ahb_bus for every AHB bus searching for AHB/APB Bridges.
+ * The AHB/APB bridges are AHB Slaves with ID GAISLER_APBMST.
+ *
+ * i0-i7, l0, l1, o6 is not available for use.
+ *
+ * Arguments
+ * - o0 Unused
+ *
+ * Results
+ * - o0 Number of found devices (1 or 0)
+ * - o2 Decremented Index if not found
+ * - o3 Address of the APB PnP configuration entry
+ * - o4 AHB Bus index of APB Bridge/APB Device
+ *
+ * Clobbered
+ * - o0 (AHB Bridge)
+ * - o2 (index is decremented)
+ * - l2 (APB DEV Index [7..4] : APBMST AHB Index [3..0])
+ * - l3 (Current AHB Bus index)
+ * - l4 (temporary storage for APB VENDOR:DEVICE)
+ * - o5 (AHB Slave ID)
+ * - o0 (clobbered by _nomem_find_ahb_bus)
+ * - g2 (Return address)
+ */
+_nomem_find_apb:
+ /* Scan all AHB Buses found for AHB/APB Bridges */
+ mov %o7, %g2 /* Save return address */
+ mov %o1, %l4 /* Save APB VENDOR:DEVICE */
+ sll %o2, 4, %l2 /* APB MST index = 0 */
+ add %g0, 1, %l3 /* AHB Bus index = 0 */
+.L2_search_next_ahb_bus:
+ call get_ahb_bridge /* Get bus %l3 I/O Area */
+ mov %l3, %o0
+ cmp %o0, %g0
+ be .L2_no_device_found /* If no more AHB bus is left to be scanned, proceed */
+ add %g0, DEV_AHB_SLV, %o5 /* Search for AHB Slave */
+ sethi %hi(AMBA_PNP_ID(VENDOR_GAISLER, GAISLER_APBMST)), %o1
+ call _nomem_find_ahb_bus /* Scan AHB bus %o0 for VENDOR:DEVICE. Index in o3 is decremented */
+ and %l2, 0xf, %o2 /* Set APBMST index */
+ cmp %o0, %g0 /* If no AHB/APB Bridge was not found, scan next AHB Bus */
+ be .L_no_apb_bridge_found /* Do next bus */
+ nop
+
+ /* The AHB/APB Bridge was found.
+ * Search for the requested APB Device on the APB bus using
+ * find_apb_bus, it will decrement the index.
+ */
+ ld [%o3 + AMBA_AHB_MBAR0_OFS], %o3
+ sll %o3, 16, %o0
+ and %o0, %o3, %o0 /* Address AND Address Mask */
+ sethi %hi(0xfff00000), %o3
+ and %o0, %o3, %o0 /* AHB/APB Bridge address */
+
+ srl %l2, 4, %o2 /* APB DEV Index */
+ call _nomem_find_apb_bus
+ mov %l4, %o1 /* APB VENDOR:DEVICE */
+ cmp %o0, %g0
+ be .L_apb_dev_not_found
+ mov %g2, %o7 /* Restore return address */
+ /* APB Device found
+ * o0 1
+ * o2 Index is decremented to zero
+ * o3 APB configuration address,
+ * o4 APB Bridge Configuration address.
+ */
+ mov %g0, %o2
+ retl
+ mov %l3, %o4
+
+.L_apb_dev_not_found:
+ /* Update APB DEV Index by saving output from find_apb_bus
+ * (index parameter) into bits [31..4] in L2.
+ */
+ sll %o2, 4, %o2
+ and %l2, 0xf, %l2
+ or %o2, %l2, %l2
+ /* Try finding the next AHB/APB Bridge on the same AHB bus
+ * to find more APB devices
+ */
+ ba .L2_search_next_ahb_bus /* Find next AHB/APB bridge */
+ inc %l2
+
+.L_no_apb_bridge_found:
+ inc %l3 /* Next AHB Bus */
+ ba .L2_search_next_ahb_bus /* Process next AHB bus */
+ andn %l2, 0xf, %l2 /* Start at APB Bridge index 0 at every AHB Bus */
+ /* No device found matching */
+.L2_no_device_found:
+ mov %g2, %o7 /* Restore return address */
+ srl %l2, 4, %o2 /* APB DEV Index */
+ retl
+ mov %g0, %o0
+
+
+
+/* FUNCTION _nomem_amba_scan_gaisler_ahb2ahb_bridge(unsigned int bridge, int bus)
+ *
+ * Constraints:
+ * - o1 may not be used
+ * - o0, o2, o3 may be used.
+ *
+ * Arguments
+ * - o0 PnP Address of Bridge AHB device
+ * - o2 PnP ID of AHB device
+ *
+ * Results
+ * - o0 Address of new bus PnP area or a 1 if AHB device is no bridge
+ *
+ * Clobbered
+ * - o0, o2
+ *
+ */
+_nomem_amba_scan_gaisler_ahb2ahb_bridge:
+ andn %o2, 0xfff, %o2
+ sethi %hi(AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_AHB2AHB)), %o3
+ cmp %o2, %o3
+ beq .L_is_ahb2ahb_bridge
+ nop
+
+ retl
+ add %g0, 1, %o0
+
+.L_is_ahb2ahb_bridge:
+ /* Found a GAISLER AHB2AHB bridge */
+ retl
+ ld [%o0 + AMBA_AHB_CUSTOM1_OFS], %o0 /* Get address of bridge PnP area */
+
+
+/* FUNCTION _nomem_amba_scan_gaisler_l2cache_bridge(unsigned int bridge, int bus)
+ *
+ * Constraints:
+ * - o1 may not be used
+ * - o0, o2, o3 may be used.
+ *
+ * Arguments
+ * - o0 PnP Address of Bridge AHB device
+ * - o2 PnP ID of AHB device
+ *
+ * Results
+ * - o0 Address of new bus PnP area or a 1 if AHB device is no bridge
+ *
+ * Clobbered
+ * - o0, o2
+ *
+ */
+_nomem_amba_scan_gaisler_l2cache_bridge:
+ andn %o2, 0xfff, %o2
+ sethi %hi(AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_L2CACHE)), %o3
+ cmp %o2, %o3
+ beq .L_is_l2cache_bridge
+ nop
+
+ retl
+ add %g0, 1, %o0
+
+.L_is_l2cache_bridge:
+ /* Found a GAISLER l2cache bridge */
+ retl
+ ld [%o0 + AMBA_AHB_CUSTOM1_OFS], %o0 /* Get address of bridge PnP area */
+
+
+/* FUNCTION _nomem_amba_scan(unsigned int bridge, int bus)
+ *
+ * Constraints:
+ * i0-i7, l0 is used by caller
+ * o5-o7 may not be used.
+ *
+ * Arguments
+ * - o0 Bridge Information: I/O AREA and parent bus
+ * - o1 Bus
+ *
+ * Results
+ * - o0 Number of AHB bridges found
+ *
+ * Clobbered
+ * - o0 (Current AHB slave conf address)
+ * - o2 (Used by insert_bridge)
+ * - o3 (Used by insert_bridge)
+ * - l1 (Number of AHB Slaves left to process)
+ * - l2 (Current AHB slave conf address)
+ * - g2 (Return address)
+ */
+_nomem_amba_scan:
+ mov %o7, %g2 /* Save return address */
+ set 16, %l1
+ cmp %o1, 1
+ be,a .L2_maxloops_detected
+ add %g0, 64, %l1
+.L2_maxloops_detected:
+
+ /* Clear 3-bit parent bus from bridge to get I/O AREA, then or
+ * (AMBA_CONF_AREA | AMBA_AHB_SLAVE_CONF_AREA) to get first AHB slave
+ * conf address.
+ */
+ andn %o0, 0x7ff, %o0
+ set (AMBA_CONF_AREA | AMBA_AHB_SLAVE_CONF_AREA), %l2
+ or %o0, %l2, %l2
+
+ /* Scan AHB Slave area for AHB<->AHB bridges. For each AHB device
+ * all "bridge drivers" are called, the driver function interface:
+ *
+ * Input:
+ * - o0 PnP Address of Bridge AHB device
+ * - o2 PnP ID of AHB device
+ * Return values:
+ * - o0 Address of new bus PnP area, returning a 1 in o2 means not found
+ *
+ * Constraints:
+ * - o1 may not be used
+ * - o0, o2, o3 may be used.
+ *
+ */
+.L_scan_one_ahb_slave:
+ ld [%l2], %o2
+
+ cmp %o2, %g0
+ beq .L_scan_next_ahb_slave
+ nop
+
+ /* Call the GAISLER AHB2AHB bridge driver */
+ call _nomem_amba_scan_gaisler_ahb2ahb_bridge
+ mov %l2, %o0
+ cmp %o0, 1
+ bne .L_found_bridge
+ ld [%l2], %o2
+
+ /* Call the GAISLER L2CACHE bridge driver */
+ call _nomem_amba_scan_gaisler_l2cache_bridge
+ mov %l2, %o0
+ cmp %o0, 1
+ bne .L_found_bridge
+ ld [%l2], %o2
+
+ /* Insert next bridge "driver" function here */
+
+
+ /* The PnP ID did not match a bridge - a new bus was not found ==>
+ * step to next AHB device */
+ ba .L_scan_next_ahb_slave
+ nop
+
+ /* Add Found bus */
+.L_found_bridge:
+ and %l2, 0x7e0, %o2
+ or %o2, %o0, %o0 /* Add AHB/AHB Bridge PnP address */
+ call insert_ahb_bridge /* Insert Bridge into found buses storage */
+ or %o1, %o0, %o0 /* Add parent bus LSB 3-bits */
+
+.L_scan_next_ahb_slave:
+ /* More Slaves to process? */
+ subcc %l1, 1, %l1
+ bne .L_scan_one_ahb_slave
+ add %l2, AMBA_AHB_CONF_LENGH, %l2
+
+ /* No more AHB devices to process */
+ mov %g2, %o7 /* Restore return address */
+ retl
+ nop
+
+/* FUNCTION _nomem_ambapp_find_buses(unsigned int ioarea)
+ *
+ * Find AMBA AHB buses.
+ *
+ * Constraints:
+ * i6-i7, l7 is used by caller
+ *
+ * Arguments
+ * - o0 Bridge Information: I/O AREA and parent bus
+ *
+ * Results
+ * - o0 Number of AHB bridges found
+ * - i0-i5 initialized
+ *
+ * Clobbered
+ * - o0 (Current AHB slave conf address)
+ * - o2 (Used by insert_bridge)
+ * - o3 (Used by insert_bridge)
+ * - l0 (Current AHB Bus)
+ * - l1 (Used by nomem_amba_scan)
+ * - l2 (Used by nomem_amba_scan)
+ * - l3 (Used by nomem_amba_scan)
+ * - l4 (Used by nomem_amba_scan)
+ *
+ * - g1 (level 1 return address)
+ * - g2 (Used by nomem_amba_scan)
+ */
+_nomem_ambapp_find_buses:
+ mov %o7, %g1 /* Save return address */
+
+ /* Initialize AHB Bus storage */
+ call init_ahb_bridges
+ nop
+
+ /* Insert AHB Bus 0 */
+ call insert_ahb_bridge
+ nop /* Argument already prepared by caller */
+
+ /* Scan AHB Bus 0 for AHB Bridges */
+ call _nomem_amba_scan
+ add %g0, 1, %o1
+
+ /* Scan all AHB Buses found for more AHB Bridges */
+ add %g0, 2, %l0
+.L100_search_next_ahb_bus:
+ call get_ahb_bridge /* Get bus %l0 I/O Area */
+ mov %l0, %o0
+ cmp %o0, %g0
+ be .L100_return /* If no more AHB bus is left to be scanned, proceed */
+ nop
+ call _nomem_amba_scan /* Scan bus %l0 for AHB Bridges. i0-i7,l0 is used */
+ mov %l0, %o1 /* I/O AREA untouched in o0 */
+ ba .L100_search_next_ahb_bus /* Do next bus */
+ add %l0, 1, %l0
+
+.L100_return:
+ mov %g1, %o7
+ retl
+ nop
+
+
+/* FUNCTION _nomem_amba_init(unsigned int ioarea)
+ *
+ * Find all AHB buses
+ *
+ * Constraints:
+ * i6, i7, o6, o7, l7, l6, g3, g4, g5, g6, g7 is used by caller
+ *
+ * Arguments
+ * - o0 Bridge Information: I/O AREA and parent bus
+ *
+ * Results
+ * - o0 Number of AHB bridges found
+ *
+ * Clobbered
+ * - l0, l1, l2, l3, l4, g1, g2 (used by _nomem_ambapp_find_buses)
+ * - o0, o1, o2, o3 (Used as arguments)
+ * - o5 (return address)
+ * - g1 (level 1 return address)
+ * - g2 (level 2 return address)
+ */
+_nomem_amba_init:
+ mov %o7, %o5 /* Save return address, o5 not used */
+
+ /* Scan for buses, it will init i0-i5 */
+ call _nomem_ambapp_find_buses
+ nop
+
+ mov %o5, %o7
+ retl
+ nop
+
+/* Call tree and their return address register
+ *
+ *_nomem_amba_scan (g1)
+ * -> init_ahb_bridges (o7)
+ * -> insert_ahb_bridge (o7)
+ * -> _nomem_amba_scan (g2)
+ * -> insert_ahb_bridge (o7)
+ * -> get_ahb_bridge (o7)
+ *
+ *
+ * -> _nomem_find_apb (g2)
+ * -> get_ahb_bridge (o7)
+ * -> _nomem_find_ahb_bus (o7)
+ * -> _nomem_find_apb_bus (o7)
+ * -> _nomem_find_ahb (g2)
+ * -> get_ahb_bridge (o7)
+ * -> _nomem_find_ahb_bus (o7)
+ * -> mem_handler.func() (o7)
+ *
+ */
diff --git a/cpu/leon3/ambapp_low_c.S b/cpu/leon3/ambapp_low_c.S
new file mode 100644
index 0000000..4ca6d55
--- /dev/null
+++ b/cpu/leon3/ambapp_low_c.S
@@ -0,0 +1,133 @@
+/* C-interface for AMBA PnP scanning functions implemented in
+ * ambapp_low.S. At the point the memory and stack can be
+ * used.
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+
+ .seg "text"
+ .extern _nomem_ambapp_find_buses
+ .extern _nomem_find_apb
+ .extern _nomem_find_ahb
+
+ .globl ambapp_find_buses
+ .globl ambapp_find_apb
+ .globl ambapp_find_ahb
+
+
+/* C-interface for _nomem_ambapp_find_buses used when memory is
+ * available.
+ */
+ambapp_find_buses:
+ save %sp, -104, %sp
+ mov %i1, %l7 /* Save second argument */
+ call _nomem_ambapp_find_buses
+ mov %i0, %o0
+
+ /* Store result */
+ st %g0, [%l7+0x00]
+ st %i0, [%l7+0x04]
+ st %i1, [%l7+0x08]
+ st %i2, [%l7+0x0c]
+ st %i3, [%l7+0x10]
+ st %i4, [%l7+0x14]
+ st %i5, [%l7+0x18]
+
+ ret
+ restore
+
+/* C-interface for _nomem_find_apb used when memory is
+ * available.
+ *
+ * void ambapp_find_apb(
+ * struct ambapp_bus *abus,
+ * unsigned int dev_vend,
+ * int index,
+ * struct ambapp_find_apb_info *result
+ * );
+ *
+ */
+ambapp_find_apb:
+ save %sp, -104, %sp
+
+ mov %i3, %l7 /* Save second argument */
+ mov %i1, %o1
+ mov %i2, %o2
+
+ /* Initialize buses available in system */
+ ld [%i0+0x08], %i1
+ ld [%i0+0x0c], %i2
+ ld [%i0+0x10], %i3
+ ld [%i0+0x14], %i4
+ ld [%i0+0x18], %i5
+
+ call _nomem_find_apb
+ ld [%i0+0x04], %i0
+
+ st %o2, [%l7+0x08] /* Decremented Index */
+ st %o3, [%l7] /* PnP configuration address of APB Device */
+ st %o4, [%l7+0x04] /* AHB Bus Index of AHB/APB bridge and APB Device */
+ mov %o0, %i0
+ ret
+ restore
+
+/* C-interface for _nomem_find_ahb used when memory is
+ * available.
+ *
+ * void ambapp_find_ahb(
+ * struct ambapp_bus *abus,
+ * unsigned int dev_vend,
+ * int index,
+ * int type,
+ * struct ambapp_find_ahb_info *result
+ * );
+ *
+ */
+ambapp_find_ahb:
+ save %sp, -104, %sp
+
+ mov %i4, %l7 /* Save second argument */
+ clr %o0
+ mov %i1, %o1
+ mov %i2, %o2
+ clr %o3
+ clr %o4
+ mov %i3, %o5
+
+ /* Initialize buses available in system */
+ ld [%i0+0x08], %i1
+ ld [%i0+0x0c], %i2
+ ld [%i0+0x10], %i3
+ ld [%i0+0x14], %i4
+ ld [%i0+0x18], %i5
+
+ call _nomem_find_ahb
+ ld [%i0+0x04], %i0
+
+ st %o2, [%l7+0x08] /* Decremented Index */
+ st %o3, [%l7] /* PnP configuration address of AHB Device */
+ st %o4, [%l7+0x04] /* AHB Bus Index of AHB Device */
+ mov %o0, %i0
+ ret
+ restore
diff --git a/cpu/leon3/cpu_init.c b/cpu/leon3/cpu_init.c
index be22ec2..046cfb8 100644
--- a/cpu/leon3/cpu_init.c
+++ b/cpu/leon3/cpu_init.c
@@ -31,6 +31,11 @@
#include <config.h>
+/* Default Plug&Play I/O area */
+#ifndef CONFIG_AMBAPP_IOAREA
+#define CONFIG_AMBAPP_IOAREA AMBA_DEFAULT_IOAREA
+#endif
+
DECLARE_GLOBAL_DATA_PTR;
/* reset CPU (jump to 0, without reset) */
@@ -53,64 +58,29 @@ struct {
/*
* Breath some life into the CPU...
*
- * Set up the memory map,
- * initialize a bunch of registers.
- *
* Run from FLASH/PROM:
- * - until memory controller is set up, only registers avaiable
+ * - memory controller has already been setup up, stack can be used
* - no global variables available for writing
* - constants avaiable
*/
-
void cpu_init_f(void)
{
- /* these varaiable must not be initialized */
- ambapp_dev_irqmp *irqmp;
- ambapp_apbdev apbdev;
- register unsigned int apbmst;
-
- /* find AMBA APB Master */
- apbmst = (unsigned int)
- ambapp_ahb_next_nomem(VENDOR_GAISLER, GAISLER_APBMST, 1, 0);
- if (!apbmst) {
- /*
- * no AHB/APB bridge, something is wrong
- * ==> jump to start (or hang)
- */
- while (1) ;
- }
- /* Init memory controller */
- if (init_memory_ctrl()) {
- while (1) ;
- }
-
- /****************************************************
- * From here we can use the main memory and the stack.
- */
- /* Find AMBA APB IRQMP Controller */
- if (ambapp_apb_first(VENDOR_GAISLER, GAISLER_IRQMP, &apbdev) != 1) {
- /* no IRQ controller, something is wrong
- * ==> jump to start (or hang)
- */
- while (1) ;
- }
- irqmp = (ambapp_dev_irqmp *) apbdev.address;
-
- /* initialize the IRQMP */
- irqmp->ilevel = 0xf; /* all IRQ off */
- irqmp->iforce = 0;
- irqmp->ipend = 0;
- irqmp->iclear = 0xfffe; /* clear all old pending interrupts */
- irqmp->cpu_mask[0] = 0; /* mask all IRQs on CPU 0 */
- irqmp->cpu_force[0] = 0; /* no force IRQ on CPU 0 */
-
- /* cache */
}
+/* Routine called from start.S,
+ *
+ * Run from FLASH/PROM:
+ * - memory controller has already been setup up, stack can be used
+ * - global variables available for read/writing
+ * - constants avaiable
+ */
void cpu_init_f2(void)
{
-
+ /* Initialize the AMBA Plug & Play bus structure, the bus
+ * structure represents the AMBA bus that the CPU is located at.
+ */
+ ambapp_bus_init(CONFIG_AMBAPP_IOAREA, CONFIG_SYS_CLK_FREQ, &ambapp_plb);
}
/*
@@ -119,95 +89,59 @@ void cpu_init_f2(void)
int cpu_init_r(void)
{
ambapp_apbdev apbdev;
+ int index, cpu;
+ ambapp_dev_gptimer *timer = NULL;
+ unsigned int bus_freq;
/*
* Find AMBA APB IRQMP Controller,
- * When we come so far we know there is a IRQMP available
*/
- ambapp_apb_first(VENDOR_GAISLER, GAISLER_IRQMP, &apbdev);
- irqmp = (ambapp_dev_irqmp *) apbdev.address;
-
- /* timer */
- if (ambapp_apb_first(VENDOR_GAISLER, GAISLER_GPTIMER, &apbdev) != 1) {
- printf("cpu_init_r: gptimer not found!\n");
- return 1;
- }
- gptimer = (ambapp_dev_gptimer *) apbdev.address;
- gptimer_irq = apbdev.irq;
-
- /* initialize prescaler common to all timers to 1MHz */
- gptimer->scalar = gptimer->scalar_reload =
- (((CONFIG_SYS_CLK_FREQ / 1000) + 500) / 1000) - 1;
-
- return (0);
-}
-
-/* find & setup memory controller */
-int init_memory_ctrl()
-{
- register ambapp_dev_mctrl *mctrl;
- register ambapp_dev_sdctrl *sdctrl;
- register ambapp_dev_ddrspa *ddrspa;
- register ambapp_dev_ddr2spa *ddr2spa;
- register ahbctrl_pp_dev *ahb;
- register unsigned int base;
- register int not_found_mctrl = -1;
-
- /* find ESA Memory controller */
- base = ambapp_apb_next_nomem(VENDOR_ESA, ESA_MCTRL, 0);
- if (base) {
- mctrl = (ambapp_dev_mctrl *) base;
-
- /* config MCTRL memory controller */
- mctrl->mcfg1 = CONFIG_SYS_GRLIB_MEMCFG1 | (mctrl->mcfg1 & 0x300);
- mctrl->mcfg2 = CONFIG_SYS_GRLIB_MEMCFG2;
- mctrl->mcfg3 = CONFIG_SYS_GRLIB_MEMCFG3;
- not_found_mctrl = 0;
+ if ( ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER,
+ GAISLER_IRQMP, 0, &apbdev) != 1 ) {
+ printf("cpu_init_r: IRQ controller not found\n");
+ while (1) ;
}
+ irqmp = (ambapp_dev_irqmp *) apbdev.address;
- /* find Gaisler Fault Tolerant Memory controller */
- base = ambapp_apb_next_nomem(VENDOR_GAISLER, GAISLER_FTMCTRL, 0);
- if (base) {
- mctrl = (ambapp_dev_mctrl *) base;
-
- /* config MCTRL memory controller */
- mctrl->mcfg1 = CONFIG_SYS_GRLIB_FT_MEMCFG1 | (mctrl->mcfg1 & 0x300);
- mctrl->mcfg2 = CONFIG_SYS_GRLIB_FT_MEMCFG2;
- mctrl->mcfg3 = CONFIG_SYS_GRLIB_FT_MEMCFG3;
- not_found_mctrl = 0;
+ /* initialize the IRQMP */
+ irqmp->ilevel = 0xf; /* all IRQ off */
+ irqmp->iforce = 0;
+ irqmp->ipend = 0;
+ irqmp->iclear = 0xfffe; /* clear all old pending interrupts */
+ for (cpu=0; cpu<16; cpu++) {
+ /* mask and clear force for all IRQs on CPU[N] */
+ irqmp->cpu_mask[cpu] = 0;
+ irqmp->cpu_force[cpu] = 0;
}
- /* find SDRAM controller */
- base = ambapp_apb_next_nomem(VENDOR_GAISLER, GAISLER_SDCTRL, 0);
- if (base) {
- sdctrl = (ambapp_dev_sdctrl *) base;
-
- /* config memory controller */
- sdctrl->sdcfg = CONFIG_SYS_GRLIB_SDRAM;
- not_found_mctrl = 0;
- }
+ /* timer */
+ index = 0;
+ while (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_GPTIMER,
+ index, &apbdev) == 1)
+ {
+ timer = (ambapp_dev_gptimer *) apbdev.address;
+ if ( gptimer == NULL ) {
+ gptimer = timer;
+ gptimer_irq = apbdev.irq;
+ }
+
+ /* Different buses may have different frequency, the
+ * frequency of the bus tell in which frequency the timer
+ * prescaler operates.
+ */
+ bus_freq = ambapp_bus_freq(&ambapp_plb, apbdev.ahb_bus_index);
- ahb = ambapp_ahb_next_nomem(VENDOR_GAISLER, GAISLER_DDR2SPA, 1, 0);
- if (ahb) {
- ddr2spa = (ambapp_dev_ddr2spa *) ambapp_ahb_get_info(ahb, 1);
+ /* initialize prescaler common to all timers to 1MHz */
+ timer->scalar = timer->scalar_reload =
+ (((bus_freq / 1000) + 500) / 1000) - 1;
- /* Config DDR2 memory controller */
- ddr2spa->cfg1 = CONFIG_SYS_GRLIB_DDR2_CFG1;
- ddr2spa->cfg3 = CONFIG_SYS_GRLIB_DDR2_CFG3;
- not_found_mctrl = 0;
+ index++;
}
-
- ahb = ambapp_ahb_next_nomem(VENDOR_GAISLER, GAISLER_DDRSPA, 1, 0);
- if (ahb) {
- ddrspa = (ambapp_dev_ddrspa *) ambapp_ahb_get_info(ahb, 1);
-
- /* Config DDR memory controller */
- ddrspa->ctrl = CONFIG_SYS_GRLIB_DDR_CFG;
- not_found_mctrl = 0;
+ if ( !gptimer ) {
+ printf("cpu_init_r: gptimer not found!\n");
+ return 1;
}
-
- /* failed to find any memory controller */
- return not_found_mctrl;
+ return (0);
}
/* Uses Timer 0 to get accurate
diff --git a/cpu/leon3/serial.c b/cpu/leon3/serial.c
index 4b2fcb8..15c380e 100644
--- a/cpu/leon3/serial.c
+++ b/cpu/leon3/serial.c
@@ -30,6 +30,11 @@
DECLARE_GLOBAL_DATA_PTR;
+/* Select which UART that will become u-boot console */
+#ifndef CONFIG_SYS_GRLIB_APBUART_INDEX
+#define CONFIG_SYS_GRLIB_APBUART_INDEX 0
+#endif
+
/* Force cache miss each time a serial controller reg is read */
#define CACHE_BYPASS 1
@@ -48,7 +53,8 @@ int serial_init(void)
unsigned int tmp;
/* find UART */
- if (ambapp_apb_first(VENDOR_GAISLER, GAISLER_APBUART, &apbdev) == 1) {
+ if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_APBUART,
+ CONFIG_SYS_GRLIB_APBUART_INDEX, &apbdev) == 1) {
leon3_apbuart = (ambapp_dev_apbuart *) apbdev.address;
diff --git a/cpu/leon3/usb_uhci.c b/cpu/leon3/usb_uhci.c
index 8f99e1d..01310e2 100644
--- a/cpu/leon3/usb_uhci.c
+++ b/cpu/leon3/usb_uhci.c
@@ -708,11 +708,11 @@ void handle_usb_interrupt(void)
*/
int usb_lowlevel_init(void)
{
- unsigned char temp;
ambapp_ahbdev ahbdev;
/* Find GRUSB core using AMBA Plug&Play information */
- if (ambapp_ahbslv_first(VENDOR_GAISLER, GAISLER_UHCI, &ahbdev) != 1) {
+ if (ambapp_ahbslv_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_UHCI,
+ CONFIG_SYS_GRLIB_GRUSB_INDEX, &ahbdev) != 1 ) {
printf("USB UHCI: Failed to find GRUSB controller\n");
return -1;
}
diff --git a/drivers/net/greth.c b/drivers/net/greth.c
index 383b25c..5ac0379 100644
--- a/drivers/net/greth.c
+++ b/drivers/net/greth.c
@@ -42,6 +42,13 @@
#define GRETH_PHY_TIMEOUT_MS 3000
#endif
+/* Let board select which GRETH to use as network interface, set
+ * this to zero if only one GRETH is available.
+ */
+#ifndef CONFIG_SYS_GRLIB_GRETH_INDEX
+#define CONFIG_SYS_GRLIB_GRETH_INDEX 0
+#endif
+
/* ByPass Cache when reading regs */
#define GRETH_REGLOAD(addr) SPARC_NOCACHE_READ(addr)
/* Write-through cache ==> no bypassing needed on writes */
@@ -605,8 +612,12 @@ int greth_initialize(bd_t * bis)
#ifdef DEBUG
printf("Scanning for GRETH\n");
#endif
- /* Find Device & IRQ via AMBA Plug&Play information */
- if (ambapp_apb_first(VENDOR_GAISLER, GAISLER_ETHMAC, &apbdev) != 1) {
+ /* Find Device & IRQ via AMBA Plug&Play information,
+ * CONFIG_SYS_GRLIB_GRETH_INDEX select which GRETH if multiple
+ * GRETHs in system.
+ */
+ if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_ETHMAC,
+ CONFIG_SYS_GRLIB_GRETH_INDEX, &apbdev) != 1) {
return -1; /* GRETH not found */
}
diff --git a/include/ambapp.h b/include/ambapp.h
index 42c990c..c1c07aa 100644
--- a/include/ambapp.h
+++ b/include/ambapp.h
@@ -3,8 +3,8 @@
* the APB bus, also freely available in GRLIB at
* www.gaisler.com.
*
- * (C) Copyright 2007
- * Daniel Hellstrom, Gaisler Research, daniel at gaisler.com.
+ * (C) Copyright 2009
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
*
* See file CREDITS for list of people who contributed to this
* project.
@@ -29,116 +29,136 @@
#ifndef __AMBAPP_H__
#define __AMBAPP_H__
-/* Default location of Plug&Play info
- * normally 0xfffff000 for AHB masters
- * and 0xfffff800 for AHB slaves.
- * Normally no need to change this.
- */
-#define LEON3_IO_AREA 0xfff00000
-#define LEON3_CONF_AREA 0xff000
-#define LEON3_AHB_SLAVE_CONF_AREA (1 << 11)
-
-/* Max devices this software will support */
-#define LEON3_AHB_MASTERS 16
-#define LEON3_AHB_SLAVES 16
-/*#define LEON3_APB_MASTERS 1*/ /* Number of APB buses that has Plug&Play */
-#define LEON3_APB_SLAVES 16 /* Total number of APB slaves per APB bus */
-
-/* Vendor codes */
-#define VENDOR_GAISLER 1
-#define VENDOR_PENDER 2
-#define VENDOR_ESA 4
-#define VENDOR_ASTRIUM 6
-#define VENDOR_OPENCHIP 7
-#define VENDOR_OPENCORES 8
-#define VENDOR_CONTRIB 9
-#define VENDOR_EONIC 11
-#define VENDOR_RADIONOR 15
-#define VENDOR_GLEICHMANN 16
-#define VENDOR_MENTA 17
-#define VENDOR_SUN 19
-#define VENDOR_EMBEDDIT 234
-#define VENDOR_CAL 202
-
-/* Gaisler Research device id's */
-#define GAISLER_LEON3 0x003
-#define GAISLER_LEON3DSU 0x004
-#define GAISLER_ETHAHB 0x005
-#define GAISLER_APBMST 0x006
-#define GAISLER_AHBUART 0x007
-#define GAISLER_SRCTRL 0x008
-#define GAISLER_SDCTRL 0x009
-#define GAISLER_APBUART 0x00C
-#define GAISLER_IRQMP 0x00D
-#define GAISLER_AHBRAM 0x00E
-#define GAISLER_GPTIMER 0x011
-#define GAISLER_PCITRG 0x012
-#define GAISLER_PCISBRG 0x013
-#define GAISLER_PCIFBRG 0x014
-#define GAISLER_PCITRACE 0x015
-#define GAISLER_PCIDMA 0x016
-#define GAISLER_AHBTRACE 0x017
-#define GAISLER_ETHDSU 0x018
-#define GAISLER_PIOPORT 0x01A
-#define GAISLER_AHBJTAG 0x01c
-#define GAISLER_SPW 0x01f
-#define GAISLER_ATACTRL 0x024
-#define GAISLER_VGA 0x061
-#define GAISLER_KBD 0X060
-#define GAISLER_ETHMAC 0x01D
-#define GAISLER_DDRSPA 0x025
-#define GAISLER_EHCI 0x026
-#define GAISLER_UHCI 0x027
-#define GAISLER_SPW2 0x029
-#define GAISLER_DDR2SPA 0x02E
-#define GAISLER_AHBSTAT 0x052
-#define GAISLER_FTMCTRL 0x054
-
-#define GAISLER_L2TIME 0xffd /* internal device: leon2 timer */
-#define GAISLER_L2C 0xffe /* internal device: leon2compat */
-#define GAISLER_PLUGPLAY 0xfff /* internal device: plug & play configarea */
-
-/* European Space Agency device id's */
-#define ESA_LEON2 0x2
-#define ESA_MCTRL 0xF
-
-/* Opencores device id's */
-#define OPENCORES_PCIBR 0x4
-#define OPENCORES_ETHMAC 0x5
-
-/* Vendor codes */
-
-/*
- *
- * Macros for manipulating Configuration registers
- *
- */
-
-#define amba_vendor(x) (((x) >> 24) & 0xff)
-
-#define amba_device(x) (((x) >> 12) & 0xfff)
-
-#define amba_membar_start(mbar) \
- (((mbar) & 0xfff00000) & (((mbar) & 0xfff0) << 16))
-
-#define amba_iobar_start(base, iobar) \
- ((base) | ((((iobar) & 0xfff00000)>>12) & (((iobar) & 0xfff0)<<4)) )
+#include <ambapp_ids.h>
-#define amba_irq(conf) ((conf) & 0xf)
+#ifndef __ASSEMBLER__
+/* Structures used to access Plug&Play information directly */
+struct ambapp_pnp_ahb {
+ const unsigned int id; /* VENDOR, DEVICE, VER, IRQ, */
+ const unsigned int custom[3];
+ const unsigned int mbar[4]; /* MASK, ADDRESS, TYPE,
+ * CACHABLE/PREFETCHABLE */
+};
+
+struct ambapp_pnp_apb {
+ const unsigned int id; /* VENDOR, DEVICE, VER, IRQ, */
+ const unsigned int iobar; /* MASK, ADDRESS, TYPE,
+ * CACHABLE/PREFETCHABLE */
+};
-#define amba_ver(conf) (((conf)>>5) & 0x1f)
+/* AMBA Plug&Play AHB Masters & Slaves information locations
+ * Max devices is 64 supported by HW, however often only 16
+ * are used.
+ */
+struct ambapp_pnp_info {
+ struct ambapp_pnp_ahb masters[64];
+ struct ambapp_pnp_ahb slaves[63];
+ const unsigned int unused[4];
+ const unsigned int systemid[4];
+};
+
+/* Describes a AMBA PnP bus */
+struct ambapp_bus {
+ int buses; /* Number of buses */
+ unsigned int ioareas[6]; /* PnP I/O AREAs of AHB buses */
+ unsigned int freq; /* Frequency of bus0 [Hz] */
+};
+
+/* Processor Local AMBA bus */
+extern struct ambapp_bus ambapp_plb;
+
+/* Get Bus frequency of a certain AMBA bus */
+extern unsigned int ambapp_bus_freq(
+ struct ambapp_bus *abus,
+ int ahb_bus_index
+ );
+
+/* AMBA PnP information of a APB Device */
+typedef struct {
+ unsigned int vendor;
+ unsigned int device;
+ unsigned char irq;
+ unsigned char ver;
+ unsigned int address;
+ unsigned int mask;
+ int ahb_bus_index;
+} ambapp_apbdev;
-#define amba_membar_type(mbar) ((mbar) & 0xf)
+/* AMBA PnP information of a AHB Device */
+typedef struct {
+ unsigned int vendor;
+ unsigned int device;
+ unsigned char irq;
+ unsigned char ver;
+ unsigned int userdef[3];
+ unsigned int address[4];
+ unsigned int mask[4];
+ int type[4];
+ int ahb_bus_index;
+} ambapp_ahbdev;
-#define amba_membar_mask(mbar) (((mbar)>>4) & 0xfff)
+/* Scan AMBA Bus for AHB Bridges */
+extern void ambapp_bus_init(
+ unsigned int ioarea,
+ unsigned int freq,
+ struct ambapp_bus *abus);
-#define AMBA_TYPE_APBIO 0x1
-#define AMBA_TYPE_MEM 0x2
-#define AMBA_TYPE_AHBIO 0x3
+/* Find APB Slave device by index using breath first search.
+ *
+ * When vendor and device are both set to zero, any device
+ * with a non-zero device ID will match the search. It may be
+ * useful when processing all devices on a AMBA bus.
+ */
+extern int ambapp_apb_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_apbdev *dev
+ );
+
+/* Find AHB Master device by index using breath first search.
+ *
+ * When vendor and device are both set to zero, any device
+ * with a non-zero device ID will match the search. It may be
+ * useful when processing all devices on a AMBA bus.
+ */
+extern int ambapp_ahbmst_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_ahbdev *dev
+ );
+
+/* Find AHB Slave device by index using breath first search.
+ *
+ * When vendor and device are both set to zero, any device
+ * with a non-zero device ID will match the search. It may be
+ * useful when processing all devices on a AMBA bus.
+ */
+extern int ambapp_ahbslv_find(
+ struct ambapp_bus *abus,
+ int vendor,
+ int device,
+ int index,
+ ambapp_ahbdev *dev
+ );
+
+/* Return number of APB Slave devices of a certain ID (VENDOR:DEVICE)
+ * zero is returned if no devices was found.
+ */
+extern int ambapp_apb_count(struct ambapp_bus *abus, int vendor, int device);
-#define AMBA_TYPE_AHBIO_ADDR(addr) (LEON3_IO_AREA | ((addr) >> 12))
+/* Return number of AHB Master devices of a certain ID (VENDOR:DEVICE)
+ * zero is returned if no devices was found.
+ */
+extern int ambapp_ahbmst_count(struct ambapp_bus *abus, int vendor, int device);
-#ifndef __ASSEMBLER__
+/* Return number of AHB Slave devices of a certain ID (VENDOR:DEVICE)
+ * zero is returned if no devices was found.
+ */
+extern int ambapp_ahbslv_count(struct ambapp_bus *abus, int vendor, int device);
#ifdef CONFIG_CMD_AMBAPP
@@ -152,109 +172,72 @@ char *ambapp_device_id2str(int vendor, int id);
/* Return name of vendor */
char *ambapp_vendor_id2str(int vendor);
-#endif
-/*
- * Types and structure used for AMBA Plug & Play bus scanning
- */
+/* Return description of a device */
+char *ambapp_device_id2desc(int vendor, int id);
-/* AMBA Plug&Play AHB information layout */
-typedef struct {
- unsigned int conf;
- unsigned int userdef[3];
- unsigned int bars[4];
-} ahbctrl_pp_dev;
-
-/* Prototypes for scanning AMBA Plug&Play bus for AMBA
- * i) AHB Masters
- * ii) AHB Slaves
- * iii) APB Slaves (APB MST is a AHB Slave)
- */
+#endif
-typedef struct {
- unsigned char irq;
- unsigned char ver;
- unsigned int address;
-} ambapp_apbdev;
+#endif /* defined(__ASSEMBLER__) */
-typedef struct {
- unsigned char irq;
- unsigned char ver;
- unsigned int userdef[3];
- unsigned int address[4];
-} ambapp_ahbdev;
+#define AMBA_DEFAULT_IOAREA 0xfff00000
+#define AMBA_CONF_AREA 0xff000
+#define AMBA_AHB_SLAVE_CONF_AREA 0x800
-/* AMBA Plug&Play AHB Masters & Slaves information locations
- * Max devices is 64 supported by HW, however often only 8
- * are used.
- */
-typedef struct {
- ahbctrl_pp_dev masters[64];
- ahbctrl_pp_dev slaves[64];
-} ahbctrl_info;
+#define DEV_NONE 0
+#define DEV_AHB_MST 1
+#define DEV_AHB_SLV 2
+#define DEV_APB_SLV 3
-/* AMBA Plug&Play AHB information layout */
-typedef struct {
- unsigned int conf;
- unsigned int bar;
-} apbctrl_pp_dev;
+#define AMBA_TYPE_APBIO 0x1
+#define AMBA_TYPE_MEM 0x2
+#define AMBA_TYPE_AHBIO 0x3
-/* All functions return the number of found devices
- * 0 = no devices found
+/* ID layout for APB and AHB devices */
+#define AMBA_PNP_ID(vendor, device) ( ((vendor)<<24) | ((device)<<12) )
+
+/* APB Slave PnP layout definitions */
+#define AMBA_APB_ID_OFS (0*4)
+#define AMBA_APB_IOBAR_OFS (1*4)
+#define AMBA_APB_CONF_LENGH (2*4)
+
+/* AHB Master/Slave layout PnP definitions */
+#define AMBA_AHB_ID_OFS (0*4)
+#define AMBA_AHB_CUSTOM0_OFS (1*4)
+#define AMBA_AHB_CUSTOM1_OFS (2*4)
+#define AMBA_AHB_CUSTOM2_OFS (3*4)
+#define AMBA_AHB_MBAR0_OFS (4*4)
+#define AMBA_AHB_MBAR1_OFS (5*4)
+#define AMBA_AHB_MBAR2_OFS (6*4)
+#define AMBA_AHB_MBAR3_OFS (7*4)
+#define AMBA_AHB_CONF_LENGH (8*4)
+
+/* Macros for extracting information from AMBA PnP information
+ * registers.
*/
-/****************************** APB SLAVES ******************************/
-int ambapp_apb_count(unsigned int vendor, unsigned int driver);
-
-int ambapp_apb_first(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev);
-
-int ambapp_apb_next(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev, int index);
-
-int ambapp_apbs_first(unsigned int vendor,
- unsigned int driver, ambapp_apbdev * dev, int max_cnt);
-
-/****************************** AHB MASTERS ******************************/
-int ambapp_ahbmst_count(unsigned int vendor, unsigned int driver);
-
-int ambapp_ahbmst_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev);
+#define amba_vendor(x) (((x) >> 24) & 0xff)
-int ambapp_ahbmst_next(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int index);
+#define amba_device(x) (((x) >> 12) & 0xfff)
-int ambapp_ahbmsts_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int max_cnt);
+#define amba_irq(conf) ((conf) & 0x1f)
-/****************************** AHB SLAVES ******************************/
-int ambapp_ahbslv_count(unsigned int vendor, unsigned int driver);
+#define amba_ver(conf) (((conf)>>5) & 0x1f)
-int ambapp_ahbslv_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev);
+#define amba_iobar_start(base, iobar) \
+ ((base) | ((((iobar) & 0xfff00000)>>12) & (((iobar) & 0xfff0)<<4)) )
-int ambapp_ahbslv_next(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int index);
+#define amba_membar_start(mbar) \
+ (((mbar) & 0xfff00000) & (((mbar) & 0xfff0) << 16))
-int ambapp_ahbslvs_first(unsigned int vendor,
- unsigned int driver, ambapp_ahbdev * dev, int max_cnt);
+#define amba_membar_type(mbar) ((mbar) & 0xf)
-/*************************** AHB/APB only regs functions *************************
- * During start up, no memory is available we can use the simplified functions
- * to get to the memory controller.
- *
- * Functions uses no stack/memory, only registers.
- */
-unsigned int ambapp_apb_next_nomem(register unsigned int vendor, /* Plug&Play Vendor ID */
- register unsigned int driver, /* Plug&Play Device ID */
- register int index);
+#define amba_membar_mask(mbar) (((mbar) >> 4) & 0xfff)
-ahbctrl_pp_dev *ambapp_ahb_next_nomem(register unsigned int vendor, /* Plug&Play Vendor ID */
- register unsigned int driver, /* Plug&Play Device ID */
- register unsigned int opts, /* scan for AHB 1=slave, 0=masters */
- register int index);
+#define amba_ahbio_adr(addr,base_ioarea) \
+ ((unsigned int)(base_ioarea) | ((addr) >> 12))
-unsigned int ambapp_ahb_get_info(ahbctrl_pp_dev * ahb, int info);
+#define amba_apb_mask(iobar) ((~(amba_membar_mask(iobar)<<8) & 0x000fffff) + 1)
/*************************** AMBA Plug&Play device register MAPS *****************/
@@ -308,6 +291,8 @@ unsigned int ambapp_ahb_get_info(ahbctrl_pp_dev * ahb, int info);
#define LEON_REG_PS2_CTRL_RI 0x00000004 /* Keyboard receive interrupt */
#define LEON_REG_PS2_CTRL_TI 0x00000008 /* Keyboard transmit interrupt */
+#ifndef __ASSEMBLER__
+
typedef struct {
volatile unsigned int ilevel;
volatile unsigned int ipend;
diff --git a/include/ambapp_ids.h b/include/ambapp_ids.h
new file mode 100644
index 0000000..b7eb98b
--- /dev/null
+++ b/include/ambapp_ids.h
@@ -0,0 +1,256 @@
+/* AMBA Plug & Play Bus Vendor and Device IDs.
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel@gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+
+#ifndef __AMBAPP_IDS_H__
+#define __AMBAPP_IDS_H__
+
+/* Vendor ID defines */
+#define VENDOR_GAISLER 0x01
+#define VENDOR_PENDER 0x02
+#define VENDOR_ESA 0x04
+#define VENDOR_ASTRIUM 0x06
+#define VENDOR_OPENCHIP 0x07
+#define VENDOR_OPENCORES 0x08
+#define VENDOR_CONTRIB 0x09
+#define VENDOR_EONIC 0x0b
+#define VENDOR_RADIONOR 0x0f
+#define VENDOR_GLEICHMANN 0x10
+#define VENDOR_MENTA 0x11
+#define VENDOR_SUN 0x13
+#define VENDOR_MOVIDIA 0x14
+#define VENDOR_ORBITA 0x17
+#define VENDOR_SYNOPSYS 0x21
+#define VENDOR_NASA 0x22
+#define VENDOR_CAL 0xca
+#define VENDOR_EMBEDDIT 0xea
+#define VENDOR_CETON 0xcb
+#define VENDOR_ACTEL 0xac
+#define VENDOR_APPLECORE 0xae
+
+/* Aeroflex Gaisler device ID defines */
+#define GAISLER_LEON2DSU 0x002
+#define GAISLER_LEON3 0x003
+#define GAISLER_LEON3DSU 0x004
+#define GAISLER_ETHAHB 0x005
+#define GAISLER_APBMST 0x006
+#define GAISLER_AHBUART 0x007
+#define GAISLER_SRCTRL 0x008
+#define GAISLER_SDCTRL 0x009
+#define GAISLER_SSRCTRL 0x00a
+#define GAISLER_APBUART 0x00c
+#define GAISLER_IRQMP 0x00d
+#define GAISLER_AHBRAM 0x00e
+#define GAISLER_AHBDPRAM 0x00f
+#define GAISLER_GPTIMER 0x011
+#define GAISLER_PCITRG 0x012
+#define GAISLER_PCISBRG 0x013
+#define GAISLER_PCIFBRG 0x014
+#define GAISLER_PCITRACE 0x015
+#define GAISLER_DMACTRL 0x016
+#define GAISLER_AHBTRACE 0x017
+#define GAISLER_DSUCTRL 0x018
+#define GAISLER_CANAHB 0x019
+#define GAISLER_GPIO 0x01a
+#define GAISLER_AHBROM 0x01b
+#define GAISLER_AHBJTAG 0x01c
+#define GAISLER_ETHMAC 0x01d
+#define GAISLER_SWNODE 0x01e
+#define GAISLER_SPW 0x01f
+#define GAISLER_AHB2AHB 0x020
+#define GAISLER_USBDC 0x021
+#define GAISLER_USB_DCL 0x022
+#define GAISLER_DDRMP 0x023
+#define GAISLER_ATACTRL 0x024
+#define GAISLER_DDRSP 0x025
+#define GAISLER_EHCI 0x026
+#define GAISLER_UHCI 0x027
+#define GAISLER_I2CMST 0x028
+#define GAISLER_SPW2 0x029
+#define GAISLER_AHBDMA 0x02a
+#define GAISLER_NUHOSP3 0x02b
+#define GAISLER_CLKGATE 0x02c
+#define GAISLER_SPICTRL 0x02d
+#define GAISLER_DDR2SP 0x02e
+#define GAISLER_SLINK 0x02f
+#define GAISLER_GRTM 0x030
+#define GAISLER_GRTC 0x031
+#define GAISLER_GRPW 0x032
+#define GAISLER_GRCTM 0x033
+#define GAISLER_GRHCAN 0x034
+#define GAISLER_GRFIFO 0x035
+#define GAISLER_GRADCDAC 0x036
+#define GAISLER_GRPULSE 0x037
+#define GAISLER_GRTIMER 0x038
+#define GAISLER_AHB2PP 0x039
+#define GAISLER_GRVERSION 0x03a
+#define GAISLER_APB2PW 0x03b
+#define GAISLER_PW2APB 0x03c
+#define GAISLER_GRCAN 0x03d
+#define GAISLER_I2CSLV 0x03e
+#define GAISLER_U16550 0x03f
+#define GAISLER_AHBMST_EM 0x040
+#define GAISLER_AHBSLV_EM 0x041
+#define GAISLER_GRTESTMOD 0x042
+#define GAISLER_ASCS 0x043
+#define GAISLER_IPMVBCTRL 0x044
+#define GAISLER_SPIMCTRL 0x045
+#define GAISLER_LEON4 0x048
+#define GAISLER_LEON4DSU 0x049
+#define GAISLER_PWM 0x04a
+#define GAISLER_L2CACHE 0x04b
+#define GAISLER_SDCTRL64 0x04c
+#define GAISLER_FTAHBRAM 0x050
+#define GAISLER_FTSRCTRL 0x051
+#define GAISLER_AHBSTAT 0x052
+#define GAISLER_LEON3FT 0x053
+#define GAISLER_FTMCTRL 0x054
+#define GAISLER_FTSDCTRL 0x055
+#define GAISLER_FTSRCTRL8 0x056
+#define GAISLER_APBPS2 0x060
+#define GAISLER_VGACTRL 0x061
+#define GAISLER_LOGAN 0x062
+#define GAISLER_SVGACTRL 0x063
+#define GAISLER_T1AHB 0x064
+#define GAISLER_MP7WRAP 0x065
+#define GAISLER_GRSYSMON 0x066
+#define GAISLER_GRACECTRL 0x067
+#define GAISLER_ATAHBSLV 0x068
+#define GAISLER_ATAHBMST 0x069
+#define GAISLER_ATAPBSLV 0x06a
+#define GAISLER_B1553BC 0x070
+#define GAISLER_B1553RT 0x071
+#define GAISLER_B1553BRM 0x072
+#define GAISLER_AES 0x073
+#define GAISLER_ECC 0x074
+#define GAISLER_PCIF 0x075
+#define GAISLER_CLKMOD 0x076
+#define GAISLER_HAPSTRAK 0x077
+#define GAISLER_TEST_1X2 0x078
+#define GAISLER_WILD2AHB 0x079
+#define GAISLER_BIO1 0x07a
+#define GAISLER_SATCAN 0x080
+#define GAISLER_CANMUX 0x081
+#define GAISLER_GRTMRX 0x082
+#define GAISLER_GRTCTX 0x083
+#define GAISLER_GRTMDESC 0x084
+#define GAISLER_GRTMVC 0x085
+#define GAISLER_GEFFE 0x086
+#define GAISLER_GPREG 0x087
+#define GAISLER_GRTMPAHB 0x088
+
+/* European Space Agency device ID defines */
+#define ESA_LEON2 0x002
+#define ESA_LEON2APB 0x003
+#define ESA_IRQ 0x005
+#define ESA_TIMER 0x006
+#define ESA_UART 0x007
+#define ESA_CFG 0x008
+#define ESA_IO 0x009
+#define ESA_MCTRL 0x00f
+#define ESA_PCIARB 0x010
+#define ESA_HURRICANE 0x011
+#define ESA_SPW_RMAP 0x012
+#define ESA_AHBUART 0x013
+#define ESA_SPWA 0x014
+#define ESA_BOSCHCAN 0x015
+#define ESA_IRQ2 0x016
+#define ESA_AHBSTAT 0x017
+#define ESA_WPROT 0x018
+#define ESA_WPROT2 0x019
+#define ESA_PDEC3AMBA 0x020
+#define ESA_PTME3AMBA 0x021
+
+/* OpenChip device ID defines */
+#define OPENCHIP_APBGPIO 0x001
+#define OPENCHIP_APBI2C 0x002
+#define OPENCHIP_APBSPI 0x003
+#define OPENCHIP_APBCHARLCD 0x004
+#define OPENCHIP_APBPWM 0x005
+#define OPENCHIP_APBPS2 0x006
+#define OPENCHIP_APBMMCSD 0x007
+#define OPENCHIP_APBNAND 0x008
+#define OPENCHIP_APBLPC 0x009
+#define OPENCHIP_APBCF 0x00a
+#define OPENCHIP_APBSYSACE 0x00b
+#define OPENCHIP_APB1WIRE 0x00c
+#define OPENCHIP_APBJTAG 0x00d
+#define OPENCHIP_APBSUI 0x00e
+
+/* Various contributions device ID defines */
+#define CONTRIB_CORE1 0x001
+#define CONTRIB_CORE2 0x002
+
+/* Gleichmann Electronics device ID defines */
+#define GLEICHMANN_CUSTOM 0x001
+#define GLEICHMANN_GEOLCD01 0x002
+#define GLEICHMANN_DAC 0x003
+#define GLEICHMANN_HPI 0x004
+#define GLEICHMANN_SPI 0x005
+#define GLEICHMANN_HIFC 0x006
+#define GLEICHMANN_ADCDAC 0x007
+#define GLEICHMANN_SPIOC 0x008
+#define GLEICHMANN_AC97 0x009
+
+/* Sun Microsystems device ID defines */
+#define SUN_T1 0x001
+#define SUN_S1 0x011
+
+/* Orbita device ID defines */
+#define ORBITA_1553B 0x001
+#define ORBITA_429 0x002
+#define ORBITA_SPI 0x003
+#define ORBITA_I2C 0x004
+#define ORBITA_SMARTCARD 0x064
+#define ORBITA_SDCARD 0x065
+#define ORBITA_UART16550 0x066
+#define ORBITA_CRYPTO 0x067
+#define ORBITA_SYSIF 0x068
+#define ORBITA_PIO 0x069
+#define ORBITA_RTC 0x0c8
+#define ORBITA_COLORLCD 0x12c
+#define ORBITA_PCI 0x190
+#define ORBITA_DSP 0x1f4
+#define ORBITA_USBHOST 0x258
+#define ORBITA_USBDEV 0x2bc
+
+/* NASA device ID defines */
+#define NASA_EP32 0x001
+
+/* CAL device ID defines */
+#define CAL_DDRCTRL 0x188
+
+/* Actel Corporation device ID defines */
+#define ACTEL_COREMP7 0x001
+
+/* AppleCore device ID defines */
+#define APPLECORE_UTLEON3 0x001
+#define APPLECORE_UTLEON3DSU 0x002
+
+/* Opencores device id's */
+#define OPENCORES_PCIBR 0x4
+#define OPENCORES_ETHMAC 0x5
+
+#endif
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 05/17] LEON3: added memory controller initialization using the new AMBA PnP routines.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (2 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 04/17] LEON3: reimplemented AMBA Plug&Play scanning routines Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 06/17] LEON3: Moved GRLIB core header files to common include/grlib directory Daniel Hellstrom
` (13 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/Makefile | 5 +-
cpu/leon3/memcfg.c | 276 ++++++++++++++++++++++++++++++++++++++
cpu/leon3/memcfg.h | 106 +++++++++++++++
cpu/leon3/memcfg_low.S | 270 +++++++++++++++++++++++++++++++++++++
cpu/leon3/start.S | 36 +++++
include/configs/gr_cpci_ax2000.h | 27 ++--
include/configs/gr_ep2s60.h | 32 +++--
include/configs/gr_xc3s_1500.h | 23 ++--
include/configs/grsim.h | 27 +++--
9 files changed, 754 insertions(+), 48 deletions(-)
create mode 100644 cpu/leon3/memcfg.c
create mode 100644 cpu/leon3/memcfg.h
create mode 100644 cpu/leon3/memcfg_low.S
diff --git a/cpu/leon3/Makefile b/cpu/leon3/Makefile
index d8f89bc..f1bb808 100644
--- a/cpu/leon3/Makefile
+++ b/cpu/leon3/Makefile
@@ -26,8 +26,9 @@ include $(TOPDIR)/config.mk
LIB = $(obj)lib$(CPU).a
START = start.o
-SOBJS = ambapp_low.o ambapp_low_c.o
-COBJS = cpu_init.o serial.o cpu.o ambapp.o interrupts.o prom.o usb_uhci.o
+SOBJS = ambapp_low.o ambapp_low_c.o memcfg_low.o
+COBJS = cpu_init.o serial.o cpu.o ambapp.o interrupts.o prom.o usb_uhci.o \
+ memcfg.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/leon3/memcfg.c b/cpu/leon3/memcfg.c
new file mode 100644
index 0000000..83e55e4
--- /dev/null
+++ b/cpu/leon3/memcfg.c
@@ -0,0 +1,276 @@
+/* GRLIB Memory controller setup. The register values are used
+ * from the associated low level assembler routine implemented
+ * in memcfg_low.S.
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <ambapp.h>
+#include "memcfg.h"
+#include <config.h>
+
+#ifdef CONFIG_SYS_GRLIB_ESA_MCTRL1
+struct mctrl_setup esa_mctrl1_cfg =
+{
+ .reg_mask = 0x7,
+ .regs =
+ {
+ {
+ .mask = 0x00000300,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3,
+ },
+ }
+};
+#ifdef CONFIG_SYS_GRLIB_ESA_MCTRL2
+struct mctrl_setup esa_mctrl2_cfg =
+{
+ .reg_mask = 0x7,
+ .regs =
+ {
+ {
+ .mask = 0x00000300,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL2_CFG1,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL2_CFG2,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_ESA_MCTRL2_CFG3,
+ },
+ }
+};
+#endif
+#endif
+
+#ifdef CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+struct mctrl_setup gaisler_ftmctrl1_cfg =
+{
+ .reg_mask = 0x7,
+ .regs =
+ {
+ {
+ .mask = 0x00000300,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3,
+ },
+ }
+};
+#ifdef CONFIG_SYS_GRLIB_GAISLER_FTMCTRL2
+struct mctrl_setup gaisler_ftmctrl2_cfg =
+{
+ .reg_mask = 0x7,
+ .regs =
+ {
+ {
+ .mask = 0x00000300,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL2_CFG1,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL2_CFG2,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_FTMCTRL2_CFG3,
+ },
+ }
+};
+#endif
+#endif
+
+#ifdef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
+struct mctrl_setup gaisler_sdctrl1_cfg =
+{
+ .reg_mask = 0x1,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_SDCTRL1_CTRL,
+ },
+ }
+};
+#ifdef CONFIG_SYS_GRLIB_GAISLER_SDCTRL2
+struct mctrl_setup gaisler_sdctrl2_cfg =
+{
+ .reg_mask = 0x1,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_SDCTRL2_CTRL,
+ },
+ }
+};
+#endif
+#endif
+
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
+struct ahbmctrl_setup gaisler_ddr2spa1_cfg =
+{
+ .ahb_mbar_no = 1,
+ .reg_mask = 0xd,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1_CFG1,
+ },
+ { 0x00000000, 0},
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1_CFG3,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1_CFG4,
+ },
+ }
+};
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA2
+struct ahbmctrl_setup gaisler_ddr2spa2_cfg =
+{
+ .ahb_mbar_no = 1,
+ .reg_mask = 0xd,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA2_CFG1,
+ },
+ { 0x00000000, 0},
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA2_CFG3,
+ },
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDR2SPA2_CFG4,
+ },
+ }
+};
+#endif
+#endif
+
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
+struct ahbmctrl_setup gaisler_ddrspa1_cfg =
+{
+ .ahb_mbar_no = 1,
+ .reg_mask = 0x1,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL,
+ },
+ }
+};
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDRSPA2
+struct ahbmctrl_setup gaisler_ddrspa2_cfg =
+{
+ .ahb_mbar_no = 1,
+ .reg_mask = 0x1,
+ .regs =
+ {
+ {
+ .mask = 0x00000000,
+ .value = CONFIG_SYS_GRLIB_GAISLER_DDRSPA2_CTRL,
+ },
+ }
+};
+#endif
+#endif
+
+struct grlib_mctrl_handler grlib_mctrl_handlers[] =
+{
+
+/* ESA MCTRL (PROM/FLASH/IO/SRAM/SDRAM) */
+#ifdef CONFIG_SYS_GRLIB_ESA_MCTRL1
+ {DEV_APB_SLV, 0, MH_UNUSED, AMBA_PNP_ID(VENDOR_ESA,ESA_MCTRL),
+ _nomem_mctrl_init, (void *)&esa_mctrl1_cfg},
+#ifdef CONFIG_SYS_GRLIB_ESA_MCTRL2
+ {DEV_APB_SLV, 1, MH_UNUSED, AMBA_PNP_ID(VENDOR_ESA,ESA_MCTRL),
+ _nomem_mctrl_init, (void *)&esa_mctrl2_cfg},
+#endif
+#endif
+
+/* GAISLER Fault Tolerant Memory controller (PROM/FLASH/IO/SRAM/SDRAM) */
+#ifdef CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+ {DEV_APB_SLV, 0, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_FTMCTRL),
+ _nomem_mctrl_init, (void *)&gaisler_ftmctrl1_cfg},
+#ifdef CONFIG_SYS_GRLIB_GAISLER_FTMCTRL2
+ {DEV_APB_SLV, 1, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_FTMCTRL),
+ _nomem_mctrl_init, (void *)&gaisler_ftmctrl2_cfg},
+#endif
+#endif
+
+/* GAISLER SDRAM-only Memory controller (SDRAM) */
+#ifdef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
+ {DEV_APB_SLV, 0, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_SDCTRL),
+ _nomem_mctrl_init, (void *)&gaisler_sdctrl1_cfg},
+#ifdef CONFIG_SYS_GRLIB_GAISLER_SDCTRL2
+ {DEV_APB_SLV, 1, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_SDCTRL),
+ _nomem_mctrl_init, (void *)&gaisler_sdctrl2_cfg},
+#endif
+#endif
+
+/* GAISLER DDR Memory controller (DDR) */
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
+ {DEV_AHB_SLV, 0, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_DDRSP),
+ _nomem_ahbmctrl_init, (void *)&gaisler_ddrspa1_cfg},
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDRSPA2
+ {DEV_AHB_SLV, 1, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_DDRSP),
+ _nomem_ahbmctrl_init, (void *)&gaisler_ddrspa2_cfg},
+#endif
+#endif
+
+/* GAISLER DDR2 Memory controller (DDR2) */
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
+ {DEV_AHB_SLV, 0, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_DDR2SP),
+ _nomem_ahbmctrl_init, (void *)&gaisler_ddr2spa1_cfg},
+#ifdef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA2
+ {DEV_AHB_SLV, 1, MH_UNUSED, AMBA_PNP_ID(VENDOR_GAISLER,GAISLER_DDR2SP),
+ _nomem_ahbmctrl_init, (void *)&gaisler_ddr2spa2_cfg},
+#endif
+#endif
+
+ /* Mark end */
+ MH_END
+};
diff --git a/cpu/leon3/memcfg.h b/cpu/leon3/memcfg.h
new file mode 100644
index 0000000..0b4738e
--- /dev/null
+++ b/cpu/leon3/memcfg.h
@@ -0,0 +1,106 @@
+/* GRLIB Memory controller setup structures
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef __MEMCFG_H__
+#define __MEMCFG_H__
+
+/*********** Low Level Memory Controller Initalization ***********/
+
+#ifndef __ASSEMBLER__
+
+typedef void (*mctrl_handler_t)(
+ struct grlib_mctrl_handler *dev,
+ void *conf,
+ unsigned int ioarea
+ );
+
+/* Memory Controller Handler Structure */
+struct grlib_mctrl_handler {
+ unsigned char type; /* 0x00. MASK: AHB MST&SLV, APB SLV */
+ char index; /* 0x01. Unit number, 0, 1, 2... */
+ char unused[2]; /* 0x02 */
+ unsigned int ven_dev; /* 0x04. Device and Vendor */
+ mctrl_handler_t func; /* 0x08. Memory Controller Handler */
+ void *priv; /* 0x0c. Optional private data, ptr to
+ * info how to set up controller */
+};
+
+extern struct grlib_mctrl_handler grlib_mctrl_handlers[];
+
+#endif
+
+#define MH_STRUCT_SIZE (4*4)
+#define MH_TYPE 0x00
+#define MH_INDEX 0x01
+#define MH_UNUSED 0x02
+#define MH_VENDOR_DEVICE 0x04
+#define MH_FUNC 0x08
+#define MH_PRIV 0x0c
+
+#define MH_TYPE_NONE DEV_NONE
+#define MH_TYPE_AHB_MST DEV_AHB_MST
+#define MH_TYPE_AHB_SLV DEV_AHB_SLV
+#define MH_TYPE_APB_SLV DEV_APB_SLV
+
+#define MH_UNUSED {0, 0}
+#define MH_END {DEV_NONE, 0, MH_UNUSED, AMBA_PNP_ID(0,0), 0, 0}
+
+/*********** Low Level Memory Controller Initalization Handlers ***********/
+
+#ifndef __ASSEMBLER__
+extern void _nomem_mctrl_init(
+ struct grlib_mctrl_handler *dev,
+ void *conf,
+ unsigned int ioarea_apbmst);
+
+struct mctrl_setup {
+ unsigned int reg_mask; /* Which registers to write */
+ struct {
+ unsigned int mask; /* Mask used keep reg bits unchanged */
+ unsigned int value; /* Value written to register */
+ } regs[8];
+};
+
+extern void _nomem_ahbmctrl_init(
+ struct grlib_mctrl_handler *dev,
+ void *conf,
+ unsigned int ioarea_apbmst);
+
+struct ahbmctrl_setup {
+ int ahb_mbar_no; /* MBAR to get register address from */
+ unsigned int reg_mask; /* Which registers to write */
+ struct {
+ unsigned int mask; /* Mask used keep reg bits unchanged */
+ unsigned int value; /* Value written to register */
+ } regs[8];
+};
+#endif
+
+/* mctrl_setup data structure defines */
+#define NREGS_OFS 0
+#define REGS_OFS 0x4
+#define REGS_SIZE 8
+
+#endif
diff --git a/cpu/leon3/memcfg_low.S b/cpu/leon3/memcfg_low.S
new file mode 100644
index 0000000..7ff7230
--- /dev/null
+++ b/cpu/leon3/memcfg_low.S
@@ -0,0 +1,270 @@
+/* This is the memory initialization functions, the function
+ * implemented below initializes each memory controller
+ * found and specified by the input grlib_mctrl_handler structure.
+ *
+ * After the memory controllers have been initialized the stack
+ * can be used.
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <ambapp.h>
+#include "memcfg.h"
+#include <config.h>
+
+ .seg "text"
+ .globl _nomem_memory_ctrl_init
+ .globl _nomem_mctrl_init, _nomem_ahbmctrl_init
+ .extern _nomem_find_apb
+ .extern _nomem_find_ahb
+
+
+/* FUNCTION
+ * _nomem_memory_controller_init(struct grlib_mctrl_handler *mem_handlers)
+ *
+ * Initialize AMBA devices, _nomem_amba_init() has prepared i0-i5
+ * with the AHB buses on the system.
+ *
+ * For each entry in mem_handlers find the VENDOR:DEVICE and handle it
+ * by calling the handler function pointer.
+ *
+ * Constraints:
+ * i6, i7, o6, l7, l6, g3, g4, g5, g6, g7 is used by caller
+ * o7 is return address
+ * l5 reserved for this function for future use.
+ *
+ * Arguments
+ * - o0 Pointer to memory handler array
+ *
+ * Results
+ * - o0 Number of memory controllers found
+ *
+ * Clobbered
+ * - o0 (Current AHB slave conf address)
+ * - l0 (mem handler entry address)
+ * - l1 (Return value, number of memory controllers found)
+ * - o7 (function pointer)
+ * - l0, l1, l2, l3, l4, g1, g2 (used by _nomem_ambapp_find_buses)
+ * - o0, o1, o2, o3, o4, o5 (Used as arguments)
+ *
+ * - g1 ( level 1 return address)
+ * - g2 ( level 2 return address)
+ */
+
+_nomem_memory_ctrl_init:
+ /* At this point all AHB buses has been found and the I/O Areas of
+ * all AHB buses is stored in the i0-i5 registers. Max 6 buses. Next,
+ * memory controllers are found by searching all buses for matching
+ * VENDOR:DEVICE. The VENDOR:DEVICE to search for are taken from the
+ * mem_handlers array. For each match the function pointer stored in
+ * the mem_handler entry is called to handle the hardware setup.
+ */
+ mov %o7, %g1 /* Save return address */
+ mov %o0, %l0
+ mov %g0, %l1 /* The return value */
+
+.L_do_one_mem_handler:
+ ld [%l0 + MH_FUNC], %o7
+ cmp %o7, %g0
+ be .L_all_mctrl_handled
+ nop
+
+ /*** Scan for memory controller ***/
+
+ /* Set up argments, o5 not used by _nomem_find_apb */
+ ldub [%l0 + MH_TYPE], %o5
+ clr %o4
+ clr %o3
+ ldub [%l0 + MH_INDEX], %o2
+ ld [%l0 + MH_VENDOR_DEVICE], %o1
+
+ /* An empty config? */
+ cmp %o5, DEV_NONE
+ beq .L_all_mctrl_next
+
+ /* Select function (APB or AHB) */
+ cmp %o5, DEV_APB_SLV
+ bne .L_find_ahb_memctrl
+ clr %o0
+.L_find_apb_memctrl:
+ call _nomem_find_apb /* Scan for APB slave device */
+ nop
+
+ /* o3 = iobar address
+ * o4 = AHB Bus index
+ *
+ * REG ADR = ((iobar >> 12) & (iobar << 4) & 0xfff00) | "APB Base"
+ */
+ ld [%o3 + AMBA_APB_IOBAR_OFS], %o5
+ srl %o5, 12, %o2
+ sll %o5, 4, %o5
+ and %o2, %o5, %o5
+ set 0xfff00, %o2
+ and %o2, %o5, %o5
+ sethi %hi(0xfff00000), %o2
+ and %o3, %o2, %o2
+ or %o5, %o2, %o5 /* Register base address */
+
+ ba .L_call_one_mem_handler
+ nop
+
+.L_find_ahb_memctrl:
+ call _nomem_find_ahb /* Scan for AHB Slave or Master.
+ * o5 determine type. */
+ nop
+ clr %o5
+
+ /* Call the handler function if the hardware was found
+ *
+ * o0 = mem_handler
+ * o1 = Configuration address
+ * o2 = AHB Bus index
+ * o3 = APB Base register (if APB Slave)
+ *
+ * Constraints:
+ * i0-i7, l0, l1, l5, g1, g3-g7 may no be used.
+ */
+.L_call_one_mem_handler:
+ cmp %o0, %g0
+ be .L_all_mctrl_next
+ mov %l0, %o0 /* Mem handler pointer */
+ mov %o3, %o1 /* AMBA PnP Configuration address */
+ mov %o4, %o2 /* AHB Bus index */
+ ld [%l0 + MH_FUNC], %o7 /* Get Function pointer */
+ call %o7
+ mov %o5, %o3 /* APB Register Base Address */
+
+ inc %l1 /* Number of Memory controllers
+ * handled. */
+
+ /* Do next entry in mem_handlers */
+.L_all_mctrl_next:
+ ba .L_do_one_mem_handler
+ add %l0, MH_STRUCT_SIZE, %l0
+
+.L_all_mctrl_handled:
+ mov %g1, %o7 /* Restore return address */
+ retl
+ mov %l1, %o0
+
+
+
+/* Generic Memory controller initialization routine (APB Registers)
+ *
+ * o0 = mem_handler structure pointer
+ * o1 = Configuration address
+ * o2 = AHB Bus index
+ * o3 = APB Base register
+ *
+ * Clobbered
+ * o0-o4
+ */
+_nomem_mctrl_init:
+ ld [%o0 + MH_PRIV], %o0 /* Get Private structure */
+ ld [%o0], %o1 /* Get Reg Mask */
+ and %o1, 0xff, %o1
+ add %o0, REGS_OFS, %o0 /* Point to first reg */
+.L_do_one_reg:
+ andcc %o1, 0x1, %g0
+ beq .L_do_next_reg
+ ld [%o0], %o2
+ ld [%o3], %o4
+ and %o4, %o2, %o4
+ ld [%o0 + 4], %o2
+ or %o4, %o2, %o4
+ st %o4, [%o3]
+
+.L_do_next_reg:
+ add %o0, REGS_SIZE, %o0
+ add %o3, 4, %o3
+ srl %o1, 1, %o1
+ cmp %o1, 0
+ bne .L_do_one_reg
+ nop
+
+ /* No more registers to write */
+ retl
+ nop
+
+
+
+/* Generic Memory controller initialization routine (AHB Registers)
+ *
+ * o0 = mem_handler structure pointer
+ * o1 = Configuration address of memory controller
+ * o2 = AHB Bus index
+ *
+ * Clobbered
+ * o0-o5
+ */
+_nomem_ahbmctrl_init:
+ ld [%o0 + MH_PRIV], %o0 /* Get Private structure */
+
+ /* Get index of AHB MBAR to get registers from */
+ ld [%o0], %o5
+ add %o0, 4, %o0
+
+ /* Get Address of MBAR in PnP info */
+ add %o5, 4, %o5
+ sll %o5, 2, %o5
+ add %o5, %o1, %o5 /* Address of MBAR */
+
+ /* Get Address of registers from PnP information
+ * Address is in AHB I/O format, i.e. relative to bus
+ *
+ * ADR = (iobar & (iobar << 16) & 0xfff00000)
+ * IOADR = (ADR >> 12) | "APB Base"
+ */
+ ld [%o5], %o5
+ sll %o5, 16, %o4
+ and %o5, %o4, %o5
+ sethi %hi(0xfff00000), %o4
+ and %o5, %o4, %o5 /* ADR */
+ and %o4, %o1, %o4
+ srl %o5, 12, %o5
+ or %o5, %o4, %o3 /* IOADR in o3 */
+
+ ld [%o0], %o1 /* Get Reg Mask */
+ and %o1, 0xff, %o1
+ add %o0, REGS_OFS, %o0 /* Point to first reg */
+.L_do_one_ahbreg:
+ andcc %o1, 0x1, %g0
+ beq .L_do_next_reg
+ ld [%o0], %o2
+ ld [%o3], %o4
+ and %o4, %o2, %o4
+ ld [%o0 + 4], %o2
+ or %o4, %o2, %o4
+ st %o4, [%o3]
+
+.L_do_next_ahbreg:
+ add %o0, REGS_SIZE, %o0
+ add %o3, 4, %o3
+ srl %o1, 1, %o1
+ cmp %o1, 0
+ bne .L_do_one_reg
+ nop
+
+ /* No more registers to write */
+ retl
+ nop
diff --git a/cpu/leon3/start.S b/cpu/leon3/start.S
index bd634bd..d9faa86 100644
--- a/cpu/leon3/start.S
+++ b/cpu/leon3/start.S
@@ -29,6 +29,12 @@
#include <asm/leon.h>
#include <timestamp.h>
#include <version.h>
+#include <ambapp.h>
+
+/* Default Plug&Play I/O area */
+#ifndef CONFIG_AMBAPP_IOAREA
+#define CONFIG_AMBAPP_IOAREA AMBA_DEFAULT_IOAREA
+#endif
/* Entry for traps which jump to a programmer-specified trap handler. */
#define TRAPR(H) \
@@ -205,6 +211,7 @@ version_string:
.ascii CONFIG_IDENT_STRING, "\0"
.section ".text"
+ .extern _nomem_amba_init, _nomem_memory_ctrl_init
.align 4
_hardreset:
@@ -256,6 +263,34 @@ stackp:
andn %fp, 0x0f, %fp
sub %fp, 64, %sp
+/* Scan AMBA Bus for AMBA buses using PnP information. All found
+ * AMBA buses I/O area will be located in i0-i5 upon return.
+ * The i0-i5 registers are later used by _nomem_amba_init2
+ */
+ambainit:
+ call _nomem_amba_init
+ sethi %hi(CONFIG_AMBAPP_IOAREA), %o0
+
+/* Scan AMBA Buses for memory controllers, then initialize the
+ * memory controllers. Note that before setting up the memory controller
+ * the stack can not be used.
+ */
+memory_ctrl_init:
+ sethi %hi(grlib_mctrl_handlers), %o0
+ call _nomem_memory_ctrl_init
+ or %o0, %lo(grlib_mctrl_handlers), %o0
+
+/* The return valu indicate how many memory controllers where found and
+ * initialized, if no memory controller was initialized, we can not continue
+ * because from here on we expect memory to be working.
+ */
+ cmp %o0, 0
+memory_ctrl_init_failed:
+ beq memory_ctrl_init_failed
+ nop
+
+/*** From now on the stack can be used. ***/
+
cpu_init_unreloc:
call cpu_init_f
nop
@@ -385,6 +420,7 @@ jump:
set board_init_f,%o1
set CONFIG_SYS_RELOC_MONITOR_BASE,%o2
+ set TEXT_START, %g1
add %o1,%o2,%o1
sub %o1,%g1,%o1
call %o1
diff --git a/include/configs/gr_cpci_ax2000.h b/include/configs/gr_cpci_ax2000.h
index d188439..b9d45dd 100644
--- a/include/configs/gr_cpci_ax2000.h
+++ b/include/configs/gr_cpci_ax2000.h
@@ -340,33 +340,36 @@
/* AMBA Plug & Play info display on startup */
/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-#define CONFIG_SYS_GRLIB_SDRAM 0
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
/* See, GRLIB Docs (grip.pdf) on how to set up
* These the memory controller registers.
*/
-#define CONFIG_SYS_GRLIB_MEMCFG1 (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x10f800ff | (1<<11))
#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x82206000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82206000
#else
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x82205260
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82205260
#endif
-#define CONFIG_SYS_GRLIB_MEMCFG3 0x0809a000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x0809a000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x10f800ff | (1<<11))
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x10f800ff | (1<<11))
#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x82206000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82206000
#else
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x82205260
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82205260
#endif
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x0809a000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x0809a000
/* no DDR controller */
-#define CONFIG_SYS_GRLIB_DDR_CFG 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
/* no DDR2 Controller */
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
/* Calculate scaler register value from default baudrate */
#define CONFIG_SYS_GRLIB_APBUART_SCALER \
diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
index 3a568ff..6edb92c 100644
--- a/include/configs/gr_ep2s60.h
+++ b/include/configs/gr_ep2s60.h
@@ -326,23 +326,29 @@
/* AMBA Plug & Play info display on startup */
/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-#define CONFIG_SYS_GRLIB_SDRAM 0
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
/* See, GRLIB Docs (grip.pdf) on how to set up
* These the memory controller registers.
*/
-#define CONFIG_SYS_GRLIB_MEMCFG1 (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x00000000
-#define CONFIG_SYS_GRLIB_MEMCFG3 0x00000000
-
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x00000000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x00000000
-
-#define CONFIG_SYS_GRLIB_DDR_CFG 0xa900830a
-
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x00000000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00000000
+
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x00000000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00000000
+
+/* DDR controller */
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL 0xa900830a
+
+/* no DDR2 Controller */
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
/* Calculate scaler register value from default baudrate */
#define CONFIG_SYS_GRLIB_APBUART_SCALER \
diff --git a/include/configs/gr_xc3s_1500.h b/include/configs/gr_xc3s_1500.h
index 4dd9a0f..1f9dd4a 100644
--- a/include/configs/gr_xc3s_1500.h
+++ b/include/configs/gr_xc3s_1500.h
@@ -288,25 +288,28 @@
/* AMBA Plug & Play info display on startup */
/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-#define CONFIG_SYS_GRLIB_SDRAM 0
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
/* See, GRLIB Docs (grip.pdf) on how to set up
* These the memory controller registers.
*/
-#define CONFIG_SYS_GRLIB_MEMCFG1 (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x82206000
-#define CONFIG_SYS_GRLIB_MEMCFG3 0x00136000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x000000ff | (1<<11))
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82206000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00136000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x82206000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x00136000
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x000000ff | (1<<11))
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82206000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00136000
/* no DDR controller */
-#define CONFIG_SYS_GRLIB_DDR_CFG 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
/* no DDR2 Controller */
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
/* Calculate scaler register value from default baudrate */
#define CONFIG_SYS_GRLIB_APBUART_SCALER \
diff --git a/include/configs/grsim.h b/include/configs/grsim.h
index c3f1a31..f815672 100644
--- a/include/configs/grsim.h
+++ b/include/configs/grsim.h
@@ -307,27 +307,32 @@
/* AMBA Plug & Play info display on startup */
/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-#define CONFIG_SYS_GRLIB_SDRAM 0
-#define CONFIG_SYS_GRLIB_MEMCFG1 (0x000000ff | (1<<11))
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
+
+/* LEON2 MCTRL configuration */
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x000000ff | (1<<11))
#if CONFIG_GRSIM
/* GRSIM configuration */
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x82206000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82206000
#else
/* TSIM configuration */
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x00001820
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x00001820
#endif
-#define CONFIG_SYS_GRLIB_MEMCFG3 0x00136000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00136000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x000000ff | (1<<11))
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x82206000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x00136000
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x000000ff | (1<<11))
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82206000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00136000
/* no DDR controller */
-#define CONFIG_SYS_GRLIB_DDR_CFG 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
/* no DDR2 Controller */
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
#define CONFIG_SYS_GRLIB_APBUART_SCALER \
((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10)
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 06/17] LEON3: Moved GRLIB core header files to common include/grlib directory
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (3 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 05/17] LEON3: added memory controller initialization using the new AMBA PnP routines Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 07/17] LEON3: serial baud rate register support multiple buses with different frequency Daniel Hellstrom
` (12 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/cpu_init.c | 10 ++--
cpu/leon3/interrupts.c | 7 ++-
cpu/leon3/memcfg.h | 1 -
cpu/leon3/prom.c | 7 ++-
cpu/leon3/serial.c | 16 +++---
drivers/net/greth.c | 2 +-
include/ambapp.h | 137 -----------------------------------------------
include/grlib/apbuart.h | 63 +++++++++++++++++++++
include/grlib/gptimer.h | 50 +++++++++++++++++
include/grlib/greth.h | 103 +++++++++++++++++++++++++++++++++++
include/grlib/irqmp.h | 39 +++++++++++++
11 files changed, 277 insertions(+), 158 deletions(-)
create mode 100644 include/grlib/apbuart.h
create mode 100644 include/grlib/gptimer.h
create mode 100644 include/grlib/greth.h
create mode 100644 include/grlib/irqmp.h
diff --git a/cpu/leon3/cpu_init.c b/cpu/leon3/cpu_init.c
index 046cfb8..e2e1181 100644
--- a/cpu/leon3/cpu_init.c
+++ b/cpu/leon3/cpu_init.c
@@ -28,6 +28,8 @@
#include <asm/asi.h>
#include <asm/leon.h>
#include <ambapp.h>
+#include <grlib/irqmp.h>
+#include <grlib/gptimer.h>
#include <config.h>
@@ -41,11 +43,7 @@ DECLARE_GLOBAL_DATA_PTR;
/* reset CPU (jump to 0, without reset) */
void start(void);
-/* find & initialize the memory controller */
-int init_memory_ctrl(void);
-
ambapp_dev_irqmp *irqmp = NULL;
-ambapp_dev_mctrl memctrl;
ambapp_dev_gptimer *gptimer = NULL;
unsigned int gptimer_irq = 0;
int leon3_snooping_avail = 0;
@@ -164,8 +162,8 @@ int timer_interrupt_init_cpu(void)
gptimer->e[0].val = 0;
gptimer->e[0].rld = 999; /* (((1000000 / 100) - 1)) */
gptimer->e[0].ctrl =
- (LEON3_GPTIMER_EN |
- LEON3_GPTIMER_RL | LEON3_GPTIMER_LD | LEON3_GPTIMER_IRQEN);
+ (GPTIMER_CTRL_EN | GPTIMER_CTRL_RS |
+ GPTIMER_CTRL_LD | GPTIMER_CTRL_IE);
return gptimer_irq;
}
diff --git a/cpu/leon3/interrupts.c b/cpu/leon3/interrupts.c
index ac6aca5..d927de1 100644
--- a/cpu/leon3/interrupts.c
+++ b/cpu/leon3/interrupts.c
@@ -39,6 +39,8 @@
#include <asm/leon.h>
#include <ambapp.h>
+#include <grlib/irqmp.h>
+#include <grlib/gptimer.h>
/* 15 normal irqs and a non maskable interrupt */
#define NR_IRQS 15
@@ -141,9 +143,8 @@ int interrupt_init_cpu(void)
/* Handle Timer 0 IRQ */
void timer_interrupt_cpu(void *arg)
{
- gptimer->e[0].ctrl = (LEON3_GPTIMER_EN |
- LEON3_GPTIMER_RL |
- LEON3_GPTIMER_LD | LEON3_GPTIMER_IRQEN);
+ gptimer->e[0].ctrl = (GPTIMER_CTRL_EN | GPTIMER_CTRL_RS |
+ GPTIMER_CTRL_LD | GPTIMER_CTRL_IE);
/* nothing to do here */
return;
}
diff --git a/cpu/leon3/memcfg.h b/cpu/leon3/memcfg.h
index 0b4738e..02086ce 100644
--- a/cpu/leon3/memcfg.h
+++ b/cpu/leon3/memcfg.h
@@ -54,7 +54,6 @@ extern struct grlib_mctrl_handler grlib_mctrl_handlers[];
#define MH_STRUCT_SIZE (4*4)
#define MH_TYPE 0x00
#define MH_INDEX 0x01
-#define MH_UNUSED 0x02
#define MH_VENDOR_DEVICE 0x04
#define MH_FUNC 0x08
#define MH_PRIV 0x0c
diff --git a/cpu/leon3/prom.c b/cpu/leon3/prom.c
index 18d2fb2..86376bb 100644
--- a/cpu/leon3/prom.c
+++ b/cpu/leon3/prom.c
@@ -32,6 +32,9 @@
#include <asm/irq.h>
#include <asm/leon.h>
#include <ambapp.h>
+#include <grlib/apbuart.h>
+#include <grlib/irqmp.h>
+#include <grlib/gptimer.h>
#include <config.h>
/*
@@ -757,14 +760,14 @@ static int PROM_TEXT leon_nbputchar(int c)
/* Wait for last character to go. */
while (!(SPARC_BYPASS_READ(&uart->status)
- & LEON_REG_UART_STATUS_THE)) ;
+ & APBUART_STATUS_THE)) ;
/* Send data */
SPARC_BYPASS_WRITE(&uart->data, c);
/* Wait for data to be sent */
while (!(SPARC_BYPASS_READ(&uart->status)
- & LEON_REG_UART_STATUS_TSE)) ;
+ & APBUART_STATUS_TSE)) ;
return 0;
}
diff --git a/cpu/leon3/serial.c b/cpu/leon3/serial.c
index 15c380e..8964310 100644
--- a/cpu/leon3/serial.c
+++ b/cpu/leon3/serial.c
@@ -27,6 +27,7 @@
#include <asm/processor.h>
#include <asm/leon.h>
#include <ambapp.h>
+#include <grlib/apbuart.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -69,9 +70,9 @@ int serial_init(void)
/* Let bit 11 be unchanged (debug bit for GRMON) */
tmp = READ_WORD(leon3_apbuart->ctrl);
- leon3_apbuart->ctrl = ((tmp & LEON_REG_UART_CTRL_DBG) |
- LEON_REG_UART_CTRL_RE |
- LEON_REG_UART_CTRL_TE);
+ leon3_apbuart->ctrl = ((tmp & APBUART_CTRL_DBG) |
+ APBUART_CTRL_RE |
+ APBUART_CTRL_TE);
return 0;
}
@@ -92,14 +93,14 @@ void serial_putc_raw(const char c)
return;
/* Wait for last character to go. */
- while (!(READ_WORD(leon3_apbuart->status) & LEON_REG_UART_STATUS_THE)) ;
+ while (!(READ_WORD(leon3_apbuart->status) & APBUART_STATUS_THE)) ;
/* Send data */
leon3_apbuart->data = c;
#ifdef LEON_DEBUG
/* Wait for data to be sent */
- while (!(READ_WORD(leon3_apbuart->status) & LEON_REG_UART_STATUS_TSE)) ;
+ while (!(READ_WORD(leon3_apbuart->status) & APBUART_STATUS_TSE)) ;
#endif
}
@@ -116,7 +117,7 @@ int serial_getc(void)
return 0;
/* Wait for a character to arrive. */
- while (!(READ_WORD(leon3_apbuart->status) & LEON_REG_UART_STATUS_DR)) ;
+ while (!(READ_WORD(leon3_apbuart->status) & APBUART_STATUS_DR)) ;
/* read data */
return READ_WORD(leon3_apbuart->data);
@@ -125,8 +126,7 @@ int serial_getc(void)
int serial_tstc(void)
{
if (leon3_apbuart)
- return (READ_WORD(leon3_apbuart->status) &
- LEON_REG_UART_STATUS_DR);
+ return (READ_WORD(leon3_apbuart->status) & APBUART_STATUS_DR);
return 0;
}
diff --git a/drivers/net/greth.c b/drivers/net/greth.c
index 5ac0379..582bc81 100644
--- a/drivers/net/greth.c
+++ b/drivers/net/greth.c
@@ -35,7 +35,7 @@
/* #define DEBUG */
-#include "greth.h"
+#include <grlib/greth.h>
/* Default to 3s timeout on autonegotiation */
#ifndef GRETH_PHY_TIMEOUT_MS
diff --git a/include/ambapp.h b/include/ambapp.h
index c1c07aa..2a4c966 100644
--- a/include/ambapp.h
+++ b/include/ambapp.h
@@ -239,141 +239,4 @@ char *ambapp_device_id2desc(int vendor, int id);
#define amba_apb_mask(iobar) ((~(amba_membar_mask(iobar)<<8) & 0x000fffff) + 1)
-/*************************** AMBA Plug&Play device register MAPS *****************/
-
-/*
- * The following defines the bits in the LEON UART Status Registers.
- */
-
-#define LEON_REG_UART_STATUS_DR 0x00000001 /* Data Ready */
-#define LEON_REG_UART_STATUS_TSE 0x00000002 /* TX Send Register Empty */
-#define LEON_REG_UART_STATUS_THE 0x00000004 /* TX Hold Register Empty */
-#define LEON_REG_UART_STATUS_BR 0x00000008 /* Break Error */
-#define LEON_REG_UART_STATUS_OE 0x00000010 /* RX Overrun Error */
-#define LEON_REG_UART_STATUS_PE 0x00000020 /* RX Parity Error */
-#define LEON_REG_UART_STATUS_FE 0x00000040 /* RX Framing Error */
-#define LEON_REG_UART_STATUS_ERR 0x00000078 /* Error Mask */
-
-/*
- * The following defines the bits in the LEON UART Ctrl Registers.
- */
-
-#define LEON_REG_UART_CTRL_RE 0x00000001 /* Receiver enable */
-#define LEON_REG_UART_CTRL_TE 0x00000002 /* Transmitter enable */
-#define LEON_REG_UART_CTRL_RI 0x00000004 /* Receiver interrupt enable */
-#define LEON_REG_UART_CTRL_TI 0x00000008 /* Transmitter interrupt enable */
-#define LEON_REG_UART_CTRL_PS 0x00000010 /* Parity select */
-#define LEON_REG_UART_CTRL_PE 0x00000020 /* Parity enable */
-#define LEON_REG_UART_CTRL_FL 0x00000040 /* Flow control enable */
-#define LEON_REG_UART_CTRL_LB 0x00000080 /* Loop Back enable */
-#define LEON_REG_UART_CTRL_DBG (1<<11) /* Debug Bit used by GRMON */
-
-#define LEON3_GPTIMER_EN 1
-#define LEON3_GPTIMER_RL 2
-#define LEON3_GPTIMER_LD 4
-#define LEON3_GPTIMER_IRQEN 8
-
-/*
- * The following defines the bits in the LEON PS/2 Status Registers.
- */
-
-#define LEON_REG_PS2_STATUS_DR 0x00000001 /* Data Ready */
-#define LEON_REG_PS2_STATUS_PE 0x00000002 /* Parity error */
-#define LEON_REG_PS2_STATUS_FE 0x00000004 /* Framing error */
-#define LEON_REG_PS2_STATUS_KI 0x00000008 /* Keyboard inhibit */
-
-/*
- * The following defines the bits in the LEON PS/2 Ctrl Registers.
- */
-
-#define LEON_REG_PS2_CTRL_RE 0x00000001 /* Receiver enable */
-#define LEON_REG_PS2_CTRL_TE 0x00000002 /* Transmitter enable */
-#define LEON_REG_PS2_CTRL_RI 0x00000004 /* Keyboard receive interrupt */
-#define LEON_REG_PS2_CTRL_TI 0x00000008 /* Keyboard transmit interrupt */
-
-#ifndef __ASSEMBLER__
-
-typedef struct {
- volatile unsigned int ilevel;
- volatile unsigned int ipend;
- volatile unsigned int iforce;
- volatile unsigned int iclear;
- volatile unsigned int mstatus;
- volatile unsigned int notused[11];
- volatile unsigned int cpu_mask[16];
- volatile unsigned int cpu_force[16];
-} ambapp_dev_irqmp;
-
-typedef struct {
- volatile unsigned int data;
- volatile unsigned int status;
- volatile unsigned int ctrl;
- volatile unsigned int scaler;
-} ambapp_dev_apbuart;
-
-typedef struct {
- volatile unsigned int val;
- volatile unsigned int rld;
- volatile unsigned int ctrl;
- volatile unsigned int unused;
-} ambapp_dev_gptimer_element;
-
-#define LEON3_GPTIMER_CTRL_EN 0x1 /* Timer enable */
-#define LEON3_GPTIMER_CTRL_RS 0x2 /* Timer reStart */
-#define LEON3_GPTIMER_CTRL_LD 0x4 /* Timer reLoad */
-#define LEON3_GPTIMER_CTRL_IE 0x8 /* interrupt enable */
-#define LEON3_GPTIMER_CTRL_IP 0x10 /* interrupt flag/pending */
-#define LEON3_GPTIMER_CTRL_CH 0x20 /* Chain with previous timer */
-
-typedef struct {
- volatile unsigned int scalar;
- volatile unsigned int scalar_reload;
- volatile unsigned int config;
- volatile unsigned int unused;
- volatile ambapp_dev_gptimer_element e[8];
-} ambapp_dev_gptimer;
-
-typedef struct {
- volatile unsigned int iodata;
- volatile unsigned int ioout;
- volatile unsigned int iodir;
- volatile unsigned int irqmask;
- volatile unsigned int irqpol;
- volatile unsigned int irqedge;
-} ambapp_dev_ioport;
-
-typedef struct {
- volatile unsigned int write;
- volatile unsigned int dummy;
- volatile unsigned int txcolor;
- volatile unsigned int bgcolor;
-} ambapp_dev_textvga;
-
-typedef struct {
- volatile unsigned int data;
- volatile unsigned int status;
- volatile unsigned int ctrl;
-} ambapp_dev_apbps2;
-
-typedef struct {
- unsigned int mcfg1, mcfg2, mcfg3;
-} ambapp_dev_mctrl;
-
-typedef struct {
- unsigned int sdcfg;
-} ambapp_dev_sdctrl;
-
-typedef struct {
- unsigned int cfg1;
- unsigned int cfg2;
- unsigned int cfg3;
-} ambapp_dev_ddr2spa;
-
-typedef struct {
- unsigned int ctrl;
- unsigned int cfg;
-} ambapp_dev_ddrspa;
-
-#endif
-
#endif
diff --git a/include/grlib/apbuart.h b/include/grlib/apbuart.h
new file mode 100644
index 0000000..92bbcdf
--- /dev/null
+++ b/include/grlib/apbuart.h
@@ -0,0 +1,63 @@
+/* GRLIB APBUART definitions
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __GRLIB_APBUART_H__
+#define __GRLIB_APBUART_H__
+
+/* APBUART Register map */
+typedef struct {
+ volatile unsigned int data;
+ volatile unsigned int status;
+ volatile unsigned int ctrl;
+ volatile unsigned int scaler;
+} ambapp_dev_apbuart;
+
+/*
+ * The following defines the bits in the LEON UART Status Registers.
+ */
+
+#define APBUART_STATUS_DR 0x00000001 /* Data Ready */
+#define APBUART_STATUS_TSE 0x00000002 /* TX Send Register Empty */
+#define APBUART_STATUS_THE 0x00000004 /* TX Hold Register Empty */
+#define APBUART_STATUS_BR 0x00000008 /* Break Error */
+#define APBUART_STATUS_OE 0x00000010 /* RX Overrun Error */
+#define APBUART_STATUS_PE 0x00000020 /* RX Parity Error */
+#define APBUART_STATUS_FE 0x00000040 /* RX Framing Error */
+#define APBUART_STATUS_ERR 0x00000078 /* Error Mask */
+
+/*
+ * The following defines the bits in the LEON UART Ctrl Registers.
+ */
+
+#define APBUART_CTRL_RE 0x00000001 /* Receiver enable */
+#define APBUART_CTRL_TE 0x00000002 /* Transmitter enable */
+#define APBUART_CTRL_RI 0x00000004 /* Receiver interrupt enable */
+#define APBUART_CTRL_TI 0x00000008 /* Transmitter interrupt enable */
+#define APBUART_CTRL_PS 0x00000010 /* Parity select */
+#define APBUART_CTRL_PE 0x00000020 /* Parity enable */
+#define APBUART_CTRL_FL 0x00000040 /* Flow control enable */
+#define APBUART_CTRL_LB 0x00000080 /* Loop Back enable */
+#define APBUART_CTRL_DBG (1<<11) /* Debug Bit used by GRMON */
+
+#endif
diff --git a/include/grlib/gptimer.h b/include/grlib/gptimer.h
new file mode 100644
index 0000000..4e79874
--- /dev/null
+++ b/include/grlib/gptimer.h
@@ -0,0 +1,50 @@
+/* GRLIB GPTIMER (General Purpose Timer) definitions
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __GRLIB_GPTIMER_H__
+#define __GRLIB_GPTIMER_H__
+
+typedef struct {
+ volatile unsigned int val;
+ volatile unsigned int rld;
+ volatile unsigned int ctrl;
+ volatile unsigned int unused;
+} ambapp_dev_gptimer_element;
+
+#define GPTIMER_CTRL_EN 0x1 /* Timer enable */
+#define GPTIMER_CTRL_RS 0x2 /* Timer reStart */
+#define GPTIMER_CTRL_LD 0x4 /* Timer reLoad */
+#define GPTIMER_CTRL_IE 0x8 /* interrupt enable */
+#define GPTIMER_CTRL_IP 0x10 /* interrupt flag/pending */
+#define GPTIMER_CTRL_CH 0x20 /* Chain with previous timer */
+
+typedef struct {
+ volatile unsigned int scalar;
+ volatile unsigned int scalar_reload;
+ volatile unsigned int config;
+ volatile unsigned int unused;
+ volatile ambapp_dev_gptimer_element e[8];
+} ambapp_dev_gptimer;
+
+#endif
diff --git a/include/grlib/greth.h b/include/grlib/greth.h
new file mode 100644
index 0000000..08cdad4
--- /dev/null
+++ b/include/grlib/greth.h
@@ -0,0 +1,103 @@
+/* Gaisler.com GRETH 10/100/1000 Ethernet MAC definitions
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __GRLIB_GRETH_H__
+#define __GRLIB_GRETH_H__
+
+#define GRETH_FD 0x10
+#define GRETH_RESET 0x40
+#define GRETH_MII_BUSY 0x8
+#define GRETH_MII_NVALID 0x10
+
+/* MII registers */
+#define GRETH_MII_EXTADV_1000FD 0x00000200
+#define GRETH_MII_EXTADV_1000HD 0x00000100
+#define GRETH_MII_EXTPRT_1000FD 0x00000800
+#define GRETH_MII_EXTPRT_1000HD 0x00000400
+
+#define GRETH_MII_100T4 0x00000200
+#define GRETH_MII_100TXFD 0x00000100
+#define GRETH_MII_100TXHD 0x00000080
+#define GRETH_MII_10FD 0x00000040
+#define GRETH_MII_10HD 0x00000020
+
+#define GRETH_BD_EN 0x800
+#define GRETH_BD_WR 0x1000
+#define GRETH_BD_IE 0x2000
+#define GRETH_BD_LEN 0x7FF
+
+#define GRETH_TXEN 0x1
+#define GRETH_INT_TX 0x8
+#define GRETH_TXI 0x4
+#define GRETH_TXBD_STATUS 0x0001C000
+#define GRETH_TXBD_MORE 0x20000
+#define GRETH_TXBD_IPCS 0x40000
+#define GRETH_TXBD_TCPCS 0x80000
+#define GRETH_TXBD_UDPCS 0x100000
+#define GRETH_TXBD_ERR_LC 0x10000
+#define GRETH_TXBD_ERR_UE 0x4000
+#define GRETH_TXBD_ERR_AL 0x8000
+#define GRETH_TXBD_NUM 128
+#define GRETH_TXBD_NUM_MASK (GRETH_TXBD_NUM-1)
+#define GRETH_TX_BUF_SIZE 2048
+
+#define GRETH_INT_RX 0x4
+#define GRETH_RXEN 0x2
+#define GRETH_RXI 0x8
+#define GRETH_RXBD_STATUS 0xFFFFC000
+#define GRETH_RXBD_ERR_AE 0x4000
+#define GRETH_RXBD_ERR_FT 0x8000
+#define GRETH_RXBD_ERR_CRC 0x10000
+#define GRETH_RXBD_ERR_OE 0x20000
+#define GRETH_RXBD_ERR_LE 0x40000
+#define GRETH_RXBD_IP_DEC 0x80000
+#define GRETH_RXBD_IP_CSERR 0x100000
+#define GRETH_RXBD_UDP_DEC 0x200000
+#define GRETH_RXBD_UDP_CSERR 0x400000
+#define GRETH_RXBD_TCP_DEC 0x800000
+#define GRETH_RXBD_TCP_CSERR 0x1000000
+
+#define GRETH_RXBD_NUM 128
+#define GRETH_RXBD_NUM_MASK (GRETH_RXBD_NUM-1)
+#define GRETH_RX_BUF_SIZE 2048
+
+/* Ethernet configuration registers */
+typedef struct _greth_regs {
+ volatile unsigned int control;
+ volatile unsigned int status;
+ volatile unsigned int esa_msb;
+ volatile unsigned int esa_lsb;
+ volatile unsigned int mdio;
+ volatile unsigned int tx_desc_p;
+ volatile unsigned int rx_desc_p;
+ volatile unsigned int edcl_ip;
+} greth_regs;
+
+/* Ethernet buffer descriptor */
+typedef struct _greth_bd {
+ volatile unsigned int stat;
+ unsigned int addr; /* Buffer address not changed by HW */
+} greth_bd;
+
+#endif
diff --git a/include/grlib/irqmp.h b/include/grlib/irqmp.h
new file mode 100644
index 0000000..1cf45ee
--- /dev/null
+++ b/include/grlib/irqmp.h
@@ -0,0 +1,39 @@
+/* GRLIB IRQMP (IRQ Multi-processor controller) definitions
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel@gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __GRLIB_IRQMP_H__
+#define __GRLIB_IRQMP_H__
+
+typedef struct {
+ volatile unsigned int ilevel;
+ volatile unsigned int ipend;
+ volatile unsigned int iforce;
+ volatile unsigned int iclear;
+ volatile unsigned int mstatus;
+ volatile unsigned int notused[11];
+ volatile unsigned int cpu_mask[16];
+ volatile unsigned int cpu_force[16];
+} ambapp_dev_irqmp;
+
+#endif
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 07/17] LEON3: serial baud rate register support multiple buses with different frequency.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (4 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 06/17] LEON3: Moved GRLIB core header files to common include/grlib directory Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 08/17] SPARC: added function that checks if IRQ is on or off Daniel Hellstrom
` (11 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/serial.c | 17 ++++++++++++++---
1 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/cpu/leon3/serial.c b/cpu/leon3/serial.c
index 8964310..1f17ede 100644
--- a/cpu/leon3/serial.c
+++ b/cpu/leon3/serial.c
@@ -47,11 +47,18 @@ DECLARE_GLOBAL_DATA_PTR;
#endif
ambapp_dev_apbuart *leon3_apbuart = NULL;
+unsigned int apbuart_freq = CONFIG_SYS_CLK_FREQ;
+
+unsigned int apbuart_calc_scaler(unsigned int apbuart_freq, unsigned int baud)
+{
+ return ((((apbuart_freq*10)/(baud*8))-5)/10);
+}
int serial_init(void)
{
ambapp_apbdev apbdev;
unsigned int tmp;
+ unsigned int freq;
/* find UART */
if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_APBUART,
@@ -65,7 +72,13 @@ int serial_init(void)
*
* Receiver & transmitter enable
*/
+#ifdef CONFIG_SYS_GRLIB_APBUART_SCALER
leon3_apbuart->scaler = CONFIG_SYS_GRLIB_APBUART_SCALER;
+#else
+ /* APBUART Frequency is equal to bus frequency */
+ freq = ambapp_bus_freq(&ambapp_plb, apbdev.ahb_bus_index);
+ leon3_apbuart->scaler = apbuart_calc_scaler(freq, CONFIG_BAUDRATE);
+#endif
/* Let bit 11 be unchanged (debug bit for GRMON) */
tmp = READ_WORD(leon3_apbuart->ctrl);
@@ -136,9 +149,7 @@ void serial_setbrg(void)
/* update baud rate settings, read it from gd->baudrate */
unsigned int scaler;
if (leon3_apbuart && (gd->baudrate > 0)) {
- scaler =
- (((CONFIG_SYS_CLK_FREQ * 10) / (gd->baudrate * 8)) -
- 5) / 10;
+ scaler = apbuart_calc_scaler(apbuart_freq, gd->baudrate);
leon3_apbuart->scaler = scaler;
}
return;
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 08/17] SPARC: added function that checks if IRQ is on or off.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (5 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 07/17] LEON3: serial baud rate register support multiple buses with different frequency Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 09/17] LEON3: added busy wait function, made wait_ms() work when IRQ is disabled Daniel Hellstrom
` (10 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
include/asm-sparc/irq.h | 3 +++
lib_sparc/interrupts.c | 7 +++++++
2 files changed, 10 insertions(+), 0 deletions(-)
diff --git a/include/asm-sparc/irq.h b/include/asm-sparc/irq.h
index c5538c0..ce78169 100644
--- a/include/asm-sparc/irq.h
+++ b/include/asm-sparc/irq.h
@@ -46,4 +46,7 @@ extern int intLock(void);
/* Sets the PIL to oldLevel */
extern void intUnlock(int oldLevel);
+/* Return non-zero if interrupts are currently enabled */
+extern int interrupt_is_enabled(void);
+
#endif
diff --git a/lib_sparc/interrupts.c b/lib_sparc/interrupts.c
index 4c73b82..4d53e8c 100644
--- a/lib_sparc/interrupts.c
+++ b/lib_sparc/interrupts.c
@@ -63,6 +63,13 @@ int disable_interrupts(void)
return intLock();
}
+int interrupt_is_enabled(void)
+{
+ if ( get_pil() == 15 )
+ return 0;
+ return 1;
+}
+
int interrupt_init(void)
{
int ret;
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 09/17] LEON3: added busy wait function, made wait_ms() work when IRQ is disabled.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (6 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 08/17] SPARC: added function that checks if IRQ is on or off Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 10/17] LEON3: added CPU count and frequency detection Daniel Hellstrom
` (9 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/cpu_init.c | 30 ++++++++++++++++++++++++++++--
1 files changed, 28 insertions(+), 2 deletions(-)
diff --git a/cpu/leon3/cpu_init.c b/cpu/leon3/cpu_init.c
index e2e1181..d2f47e1 100644
--- a/cpu/leon3/cpu_init.c
+++ b/cpu/leon3/cpu_init.c
@@ -142,14 +142,40 @@ int cpu_init_r(void)
return (0);
}
+/* Busy wait a number of ms */
+void cpu_wait_ms_busy(unsigned long ms)
+{
+ unsigned int ms_delay;
+ volatile unsigned int tmp;
+
+ /* ~10-20 cycles per decrement */
+ ms_delay = leon_cpu_freq / (1000 * 10);
+ do {
+ /* Wait ~1ms */
+ tmp = ms_delay;
+ while ( tmp-- > 0 )
+ ;
+ } while ( --ms > 0 );
+}
+
/* Uses Timer 0 to get accurate
* pauses. Max 2 raised to 32 ticks
*
*/
void cpu_wait_ticks(unsigned long ticks)
{
- unsigned long start = get_timer(0);
- while (get_timer(start) < ticks) ;
+ unsigned long start;
+
+ if ( interrupt_is_enabled() ) {
+ start = get_timer(0);
+ while (get_timer(start) < ticks) ;
+ } else {
+ /* Interrupts disabled, this means that we cannot
+ * use get_timer(), it relies on IRQ. Instead the
+ * CPU frequency is used.
+ */
+ cpu_wait_ms_busy( ticks2usec(ticks) / 1000 );
+ }
}
/* initiate and setup timer0 interrupt to 1MHz
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 10/17] LEON3: added CPU count and frequency detection.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (7 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 09/17] LEON3: added busy wait function, made wait_ms() work when IRQ is disabled Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 11/17] SPARC: removed USB stop from linux bootm, arch-independent bootm stop USB Daniel Hellstrom
` (8 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/cpu.c | 42 +++++++++++++++++++++++++++++++++++++++++-
include/asm-sparc/leon3.h | 13 +++++++++++++
2 files changed, 54 insertions(+), 1 deletions(-)
diff --git a/cpu/leon3/cpu.c b/cpu/leon3/cpu.c
index 976f311..5cc9513 100644
--- a/cpu/leon3/cpu.c
+++ b/cpu/leon3/cpu.c
@@ -29,15 +29,55 @@
#include <asm/io.h>
#include <asm/processor.h>
+#include <ambapp.h>
DECLARE_GLOBAL_DATA_PTR;
extern void _reset_reloc(void);
+int leon_cpu_cnt = 1;
+int leon_ver = 3;
+unsigned int leon_cpu_freq = CONFIG_SYS_CLK_FREQ;
+
+int cpu_freq(void)
+{
+ ambapp_ahbdev dev;
+
+ if ( leon_ver == 3 ) {
+ ambapp_ahbmst_find(&ambapp_plb, VENDOR_GAISLER,
+ GAISLER_LEON3, 0, &dev);
+ } else {
+ ambapp_ahbmst_find(&ambapp_plb, VENDOR_GAISLER,
+ GAISLER_LEON4, 0, &dev);
+ }
+
+ leon_cpu_freq = ambapp_bus_freq(&ambapp_plb, dev.ahb_bus_index);
+}
+
int checkcpu(void)
{
+ int cnt;
+ char str[4];
+
/* check LEON version here */
- printf("CPU: LEON3\n");
+ cnt = ambapp_ahbmst_count(&ambapp_plb, VENDOR_GAISLER, GAISLER_LEON3);
+ if ( cnt <= 0 ) {
+ cnt = ambapp_ahbmst_count(&ambapp_plb, VENDOR_GAISLER, GAISLER_LEON4);
+ if ( cnt > 0 )
+ leon_ver = 4;
+ }
+
+ cpu_freq();
+
+ str[0] = '\0';
+ if ( cnt > 1 ) {
+ leon_cpu_cnt = cnt;
+ str[0] = '0' + cnt;
+ str[1] = 'x';
+ str[2] = '\0';
+ }
+ printf("CPU: %sLEON%d @ %dMHz\n", str, leon_ver, leon_cpu_freq / 1000000);
+
return 0;
}
diff --git a/include/asm-sparc/leon3.h b/include/asm-sparc/leon3.h
index b90d35b..60396c4 100644
--- a/include/asm-sparc/leon3.h
+++ b/include/asm-sparc/leon3.h
@@ -33,4 +33,17 @@
* ctrl, memory controllers etc.
*/
+
+#ifndef __ASSEMBLER__
+/* The frequency of the CPU */
+extern unsigned int leon_cpu_freq;
+
+/* Number of LEON processors in system */
+extern int leon_cpu_cnt;
+
+/* Ver/subversion of CPU */
+extern int leon_ver;
+
+#endif /* __ASSEMBLER__ */
+
#endif
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 11/17] SPARC: removed USB stop from linux bootm, arch-independent bootm stop USB.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (8 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 10/17] LEON3: added CPU count and frequency detection Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 12/17] SPARC: added optional cpu_late_init routine Daniel Hellstrom
` (7 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
lib_sparc/bootm.c | 8 --------
1 files changed, 0 insertions(+), 8 deletions(-)
diff --git a/lib_sparc/bootm.c b/lib_sparc/bootm.c
index c62cf57..f517325 100644
--- a/lib_sparc/bootm.c
+++ b/lib_sparc/bootm.c
@@ -35,10 +35,6 @@ extern image_header_t header;
extern void srmmu_init_cpu(unsigned int entry);
extern void prepare_bootargs(char *bootargs);
-#ifdef CONFIG_USB_UHCI
-extern int usb_lowlevel_stop(void);
-#endif
-
/* sparc kernel argument (the ROM vector) */
struct linux_romvec *kernel_arg_promvec;
@@ -125,10 +121,6 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t * images)
linux_hdr->linuxver_minor, linux_hdr->linuxver_revision);
#endif
-#ifdef CONFIG_USB_UHCI
- usb_lowlevel_stop();
-#endif
-
/* set basic boot params in kernel header now that it has been
* extracted and is writeable.
*/
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 12/17] SPARC: added optional cpu_late_init routine.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (9 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 11/17] SPARC: removed USB stop from linux bootm, arch-independent bootm stop USB Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 13/17] LEON3: Added GRETH EDCL debug link IP address initialization Daniel Hellstrom
` (6 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
lib_sparc/board.c | 5 +++++
1 files changed, 5 insertions(+), 0 deletions(-)
diff --git a/lib_sparc/board.c b/lib_sparc/board.c
index 11eea60..d829af0 100644
--- a/lib_sparc/board.c
+++ b/lib_sparc/board.c
@@ -65,6 +65,7 @@ extern void timer_interrupt_init(void);
extern void malloc_bin_reloc(void);
extern int do_ambapp_print(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[]);
extern int prom_init(void);
+extern void cpu_late_init(void);
#if defined(CONFIG__CMD_DOC)
void doc_init(void);
@@ -353,6 +354,10 @@ void board_init_f(ulong bootflag)
/* relocate environment function pointers etc. */
env_relocate();
+#if defined(CONFIG_CPU_LATE_INIT)
+ cpu_late_init();
+#endif
+
#if defined(CONFIG_BOARD_LATE_INIT)
board_late_init();
#endif
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 13/17] LEON3: Added GRETH EDCL debug link IP address initialization.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (10 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 12/17] SPARC: added optional cpu_late_init routine Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 14/17] LEON: added support for GRLIB SPI Memory controller, spi command interface Daniel Hellstrom
` (5 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/cpu_init.c | 14 +++++
cpu/leon3/greth.c | 152 ++++++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 166 insertions(+), 0 deletions(-)
create mode 100644 cpu/leon3/greth.c
diff --git a/cpu/leon3/cpu_init.c b/cpu/leon3/cpu_init.c
index d2f47e1..39c4bb8 100644
--- a/cpu/leon3/cpu_init.c
+++ b/cpu/leon3/cpu_init.c
@@ -43,6 +43,9 @@ DECLARE_GLOBAL_DATA_PTR;
/* reset CPU (jump to 0, without reset) */
void start(void);
+/* Initialize GRETH EDCL on startup */
+extern void greth_edcl_init(void);
+
ambapp_dev_irqmp *irqmp = NULL;
ambapp_dev_gptimer *gptimer = NULL;
unsigned int gptimer_irq = 0;
@@ -142,6 +145,17 @@ int cpu_init_r(void)
return (0);
}
+/* Late CPU initialization
+ *
+ * At this point environment variables is available.
+ */
+void cpu_late_init(void)
+{
+#ifdef CONFIG_SYS_GRETH_EDCL_IP
+ greth_edcl_init();
+#endif
+}
+
/* Busy wait a number of ms */
void cpu_wait_ms_busy(unsigned long ms)
{
diff --git a/cpu/leon3/greth.c b/cpu/leon3/greth.c
new file mode 100644
index 0000000..7f341e6
--- /dev/null
+++ b/cpu/leon3/greth.c
@@ -0,0 +1,152 @@
+/* GRETH EDCL IP number initialization
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ambapp.h>
+#include <config.h>
+#include <grlib/greth.h>
+
+#ifdef CONFIG_SYS_GRETH_EDCL_IP
+
+/* Set EDCL IP of GRETH[core_index] to IP number as indicated by ip_str
+ *
+ * This is useful for designs that have a disabled EDCL (IP=0.0.0.0) on
+ * reset, or when the default EDCL IP is no correct. Often 192.168.0.51
+ * is default, the IP must be unique which is a problem when multiple
+ * boards are used.
+ *
+ * NOTE: The EDCL IP must not be the same IP as U-BOOT is using.
+ *
+ * NOTE: This code should not be located in the GRETH driver, because
+ * we might want to set the EDCL debug link IP but not enable
+ * u-boot networking.
+ */
+int greth_edcl_ip_set(int core_index, char *ip_str)
+{
+ ambapp_apbdev apbdev;
+ unsigned int *greth_ip_reg;
+ unsigned int ip;
+ char *start, *end;
+ unsigned char ipbyte;
+ int i;
+
+ /* Find Device & IRQ via AMBA Plug&Play information,
+ * CONFIG_SYS_GRLIB_GRETH_INDEX select which GRETH if multiple
+ * GRETHs in system.
+ */
+ if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_ETHMAC,
+ core_index, &apbdev) != 1) {
+ return -1; /* GRETH not found */
+ }
+ greth_ip_reg = (unsigned int *)(apbdev.address + 0x1C);
+
+ /* Convert IP String into IP number */
+ ip = 0;
+ start = ip_str;
+ for (i = 0; i < 4; i++) {
+ ipbyte = simple_strtoul(start, &end, 10);
+ ip |= ipbyte << (24-i*8);
+ start = end + 1; /* Next byte in IP-string */
+ }
+
+ /* Set new IP address of EDCL */
+ *greth_ip_reg = ip;
+
+ printf("GRETH[0x%08x] EDCL IP: %s\n",
+ (unsigned int)greth_ip_reg, ip_str);
+
+ return 0;
+};
+
+char *greth_edcl_ip_table[8] =
+{
+#ifdef CONFIG_SYS_GRETH0_EDCL_IP_STR
+ CONFIG_SYS_GRETH0_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH1_EDCL_IP_STR
+ CONFIG_SYS_GRETH1_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH2_EDCL_IP_STR
+ CONFIG_SYS_GRETH2_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH3_EDCL_IP_STR
+ CONFIG_SYS_GRETH3_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH4_EDCL_IP_STR
+ CONFIG_SYS_GRETH4_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH5_EDCL_IP_STR
+ CONFIG_SYS_GRETH5_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH6_EDCL_IP_STR
+ CONFIG_SYS_GRETH6_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+#ifdef CONFIG_SYS_GRETH7_EDCL_IP_STR
+ CONFIG_SYS_GRETH7_EDCL_IP_STR,
+#else
+ NULL,
+#endif
+};
+
+void greth_edcl_init(void)
+{
+ int i;
+ char *ip_str;
+ char envname[16];
+
+ /* Set EDCL IP of the first 8 cores, if requested by user through
+ * Environment variable "greth_edcl_ipN" when N identifies which
+ * GRETH core, or through defines set in board configuration.
+ */
+ strcpy(envname, "greth_edcl_ipX");
+ for (i=0; i<8; i++) {
+ /* Is there a config for */
+ envname[13] = '0' + i;
+ ip_str = getenv(envname);
+ if ( ip_str == NULL ) {
+ ip_str = greth_edcl_ip_table[i];
+ }
+ if ( ip_str != NULL ) {
+ if ( greth_edcl_ip_set(i, ip_str) )
+ break;
+ }
+ }
+}
+
+#endif
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 14/17] LEON: added support for GRLIB SPI Memory controller, spi command interface.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (11 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 13/17] LEON3: Added GRETH EDCL debug link IP address initialization Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 15/17] LEON3: fixed MMU table for systems with larger memory than 128MB Daniel Hellstrom
` (4 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
drivers/spi/Makefile | 1 +
drivers/spi/spimctrl_spi.c | 261 ++++++++++++++++++++++++++++++++++++++++++++
include/grlib/spimctrl.h | 69 ++++++++++++
lib_sparc/board.c | 14 +++
4 files changed, 345 insertions(+), 0 deletions(-)
create mode 100644 drivers/spi/spimctrl_spi.c
create mode 100644 include/grlib/spimctrl.h
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 824d8e7..a730d45 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -34,6 +34,7 @@ COBJS-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o
COBJS-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
COBJS-$(CONFIG_MXC_SPI) += mxc_spi.o
COBJS-$(CONFIG_SOFT_SPI) += soft_spi.o
+COBJS-$(CONFIG_SPIMCTRL_SPI) += spimctrl_spi.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --git a/drivers/spi/spimctrl_spi.c b/drivers/spi/spimctrl_spi.c
new file mode 100644
index 0000000..a37cfa9
--- /dev/null
+++ b/drivers/spi/spimctrl_spi.c
@@ -0,0 +1,261 @@
+/* SPI interface driver for GRLIB SPIMCTRL (SPI Memory controller)
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom <daniel@gaisler.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <spi.h>
+#include <ambapp.h>
+#include <grlib/spimctrl.h>
+
+struct spimctrl_priv {
+ struct spimctrl_regs *regs;
+ int irq;
+ unsigned int mode;
+ unsigned int max_hz;
+};
+
+struct spi_slave_internal {
+ struct spi_slave dev;
+ struct spimctrl_priv *priv;
+ int locked;
+};
+
+static int spimctrl_cnt = 0;
+static struct spimctrl_priv *spimctrl_devs;
+
+int spimctrl_probe(void)
+{
+ int cnt, i, found;
+ ambapp_ahbdev ahbdev;
+ struct spimctrl_priv *priv;
+
+ cnt = ambapp_ahbslv_count(&ambapp_plb,VENDOR_GAISLER,GAISLER_SPIMCTRL);
+ debug("Found %d SPIMCTRLS\n", cnt);
+ if ( cnt < 1 )
+ return 0;
+
+ spimctrl_cnt = cnt;
+ spimctrl_devs = (struct spimctrl_priv *) malloc(sizeof(*priv) * cnt);
+ memset(spimctrl_devs, 0, sizeof(struct spimctrl_priv) * cnt);
+
+ for (i=0; i<cnt; i++) {
+ found = ambapp_ahbslv_find(&ambapp_plb, VENDOR_GAISLER,
+ GAISLER_SPIMCTRL, i, &ahbdev);
+ if ( !found ) {
+ printf("spimctrl_probe: internal AMBA error\n");
+ while (1) ;
+ }
+
+ priv = &spimctrl_devs[i];
+ priv->regs = (struct spimctrl_regs *)ahbdev.address[0];
+ priv->irq = ahbdev.irq;
+
+ debug("SPIMCTRL[%d]: 0x%x irq %d\n",
+ i, (unsigned int)priv->regs, priv->irq);
+ }
+
+ return cnt;
+}
+
+void spimctrl_init(struct spimctrl_priv *priv)
+{
+ debug("SPIMCTRL_INIT\n");
+
+ /* Finish any previous ongoing user activity, this should
+ * not normally happen, but may when debugging.
+ */
+ if ( priv->regs->stat & SPIMCTRL_STAT_DONE )
+ priv->regs->stat = SPIMCTRL_STAT_DONE;
+
+ if ( priv->regs->ctrl & SPIMCTRL_CTRL_USRC ) {
+ /* Exit User mode */
+ priv->regs->ctrl = SPIMCTRL_CTRL_CSN;
+ }
+}
+
+void spimctrl_cs_activate(struct spimctrl_priv *priv)
+{
+ debug("CS ACT\n");
+
+ if ( priv->regs->stat & SPIMCTRL_STAT_DONE )
+ priv->regs->stat = SPIMCTRL_STAT_DONE;
+
+ /* Enter User mode */
+ priv->regs->ctrl = SPIMCTRL_CTRL_CSN | SPIMCTRL_CTRL_USRC;
+
+ /* Lower chip-select */
+ priv->regs->ctrl = SPIMCTRL_CTRL_USRC;
+}
+
+void spimctrl_cs_deactivate(struct spimctrl_priv *priv)
+{
+ debug("CS INACT\n");
+
+ /* Rise chip select */
+ priv->regs->ctrl = SPIMCTRL_CTRL_CSN | SPIMCTRL_CTRL_USRC;
+
+ /* Exit User mode */
+ priv->regs->ctrl = SPIMCTRL_CTRL_CSN;
+}
+
+void spimctrl_transfer_byte(struct spimctrl_priv *priv, char *out, char *in)
+{
+ unsigned int stat;
+ unsigned char rx;
+
+ while( (stat=priv->regs->stat) &
+ (SPIMCTRL_STAT_BUSY|SPIMCTRL_STAT_DONE) ) {
+ debug("WAITING1: 0x%x\n", stat);
+ }
+ debug("OK STAT1: 0x%x\n", stat);
+
+ if ( out ) {
+ priv->regs->tx = out[0];
+ } else {
+ priv->regs->tx = 0;
+ }
+
+ while ( ((stat=priv->regs->stat) & SPIMCTRL_STAT_DONE) == 0 ) {
+ debug("WAITING2: 0x%x\n", stat);
+ }
+ debug("OK STAT2: 0x%x\n", stat);
+ rx = priv->regs->rx;
+ if ( in ) {
+ in[0] = rx;
+ }
+ priv->regs->stat = SPIMCTRL_STAT_DONE;
+
+ if ( out && in ) {
+ debug("OUT 0x%02x ; IN 0x%02x\n", out[0], in[0]);
+ } else if ( out ) {
+ debug("OUT 0x%02x\n", out[0]);
+ } else if ( in ) {
+ debug("IN: 0x%02x\n", in[0]);
+ }
+}
+
+void spi_init(void)
+{
+ int i;
+
+ debug("SPI INIT\n");
+
+ /* Find SPIMCTRL cores */
+ spimctrl_probe();
+
+ /* Init SPIMCTRL Core */
+ for ( i=0; i<spimctrl_cnt; i++) {
+ spimctrl_init(&spimctrl_devs[i]);
+ }
+}
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+ unsigned int max_hz, unsigned int mode)
+{
+ struct spi_slave_internal *slave;
+
+ debug("spi_setup_slave(%d, %d, %d, %d)\n", bus, cs, max_hz, mode);
+
+ if ( bus >= spimctrl_cnt ) {
+ printf("spi_setup_slave: NO SUCH BUS: %d\n", bus);
+ return NULL;
+ }
+
+ slave = malloc(sizeof(struct spi_slave_internal));
+ if (!slave)
+ return NULL;
+
+ slave->dev.bus = bus;
+ slave->dev.cs = cs;
+ slave->priv = &spimctrl_devs[bus];
+ slave->priv->mode = mode;
+ slave->priv->max_hz = max_hz;
+ slave->locked = 0;
+
+ return &slave->dev;
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+ free(slave);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+ struct spi_slave_internal *slv = (void *)slave;
+
+ if ( slv->locked )
+ return -1;
+ slv->locked = 1;
+
+ return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+ struct spi_slave_internal *slv = (void *)slave;
+
+ slv->locked = 0;
+ return;
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
+ void *din, unsigned long flags)
+{
+ struct spi_slave_internal *slv = (void *)slave;
+ int i, cnt;
+ unsigned char *out, *in;
+
+ debug("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n",
+ slave->bus, slave->cs, (uint)dout, (uint)din, bitlen);
+
+ if ( (bitlen & 0x7) != 0 ) {
+ printf("spi_xfer: Bitlength of != 8 not supported\n");
+ return -1;
+ }
+
+ if (flags & SPI_XFER_BEGIN) {
+ /* Set Chip Select */
+ spimctrl_cs_activate(slv->priv);
+ }
+
+ out = (unsigned char *)dout;
+ in = (unsigned char *)din;
+ cnt = bitlen / 8;
+ for (i=0; i<cnt; i++){
+ spimctrl_transfer_byte(slv->priv, out, in);
+
+ if ( out )
+ out++;
+ if ( in )
+ in++;
+ }
+
+ if (flags & SPI_XFER_END) {
+ /* End transfer by rising ChipSelect again */
+ spimctrl_cs_deactivate(slv->priv);
+ }
+
+ return 0;
+}
diff --git a/include/grlib/spimctrl.h b/include/grlib/spimctrl.h
new file mode 100644
index 0000000..8329745
--- /dev/null
+++ b/include/grlib/spimctrl.h
@@ -0,0 +1,69 @@
+/* GRLIB SPI Memory controller (SPIMCTRL) definitions
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __GRLIB_SPIMCTRL_H__
+#define __GRLIB_SPIMCTRL_H__
+
+/*** REGISTER LAYOUT ***/
+struct spimctrl_regs {
+ volatile unsigned int conf; /* 0x00 */
+ volatile unsigned int ctrl; /* 0x04 */
+ volatile unsigned int stat; /* 0x08 */
+ volatile unsigned int rx; /* 0x0C */
+ volatile unsigned int tx; /* 0x10 */
+};
+
+/*** CONFIGURATION REGISTER 0x00 ***/
+#define SPIMCTRL_CONF_READCMD_BIT 0
+#define SPIMCTRL_CONF_READCMD 0xff
+
+/*** CONTROL REGISTER 0x04 ***/
+#define SPIMCTRL_CTRL_USRC_BIT 0
+#define SPIMCTRL_CTRL_IEN_BIT 1
+#define SPIMCTRL_CTRL_EAS_BIT 2
+#define SPIMCTRL_CTRL_CSN_BIT 3
+#define SPIMCTRL_CTRL_RST_BIT 4
+
+#define SPIMCTRL_CTRL_USRC (1<<SPIMCTRL_CTRL_USRC_BIT)
+#define SPIMCTRL_CTRL_IEN (1<<SPIMCTRL_CTRL_IEN_BIT)
+#define SPIMCTRL_CTRL_EAS (1<<SPIMCTRL_CTRL_EAS_BIT)
+#define SPIMCTRL_CTRL_CSN (1<<SPIMCTRL_CTRL_CSN_BIT)
+#define SPIMCTRL_CTRL_RST (1<<SPIMCTRL_CTRL_RST_BIT)
+
+/*** STATUS REGISTER 0x08 ***/
+#define SPIMCTRL_STAT_DONE_BIT 0
+#define SPIMCTRL_STAT_BUSY_BIT 1
+#define SPIMCTRL_STAT_INT_BIT 2
+#define SPIMCTRL_STAT_ERR_BIT 3
+#define SPIMCTRL_STAT_TO_BIT 4
+#define SPIMCTRL_STAT_CD_BIT 5
+
+#define SPIMCTRL_STAT_DONE (1<<SPIMCTRL_STAT_DONE_BIT)
+#define SPIMCTRL_STAT_BUSY (1<<SPIMCTRL_STAT_BUSY_BIT)
+#define SPIMCTRL_STAT_INT (1<<SPIMCTRL_STAT_INT_BIT)
+#define SPIMCTRL_STAT_ERR (1<<SPIMCTRL_STAT_ERR_BIT)
+#define SPIMCTRL_STAT_TO (1<<SPIMCTRL_STAT_TO_BIT)
+#define SPIMCTRL_STAT_CD (1<<SPIMCTRL_STAT_CD_BIT)
+
+#endif
diff --git a/lib_sparc/board.c b/lib_sparc/board.c
index d829af0..3362f39 100644
--- a/lib_sparc/board.c
+++ b/lib_sparc/board.c
@@ -97,6 +97,16 @@ static int init_baudrate(void)
return (0);
}
+#if defined(CONFIG_HARD_SPI)
+static int init_func_spi (void)
+{
+ puts ("SPI: ");
+ spi_init ();
+ puts ("ready\n");
+ return (0);
+}
+#endif
+
/***********************************************************************/
/*
@@ -304,6 +314,10 @@ void board_init_f(ulong bootflag)
CONFIG_SYS_MALLOC_END - CONFIG_SYS_MALLOC_BASE);
malloc_bin_reloc();
+#if defined(CONFIG_HARD_SPI)
+ init_func_spi();
+#endif
+
#if !defined(CONFIG_SYS_NO_FLASH)
puts("FLASH: ");
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 15/17] LEON3: fixed MMU table for systems with larger memory than 128MB.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (12 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 14/17] LEON: added support for GRLIB SPI Memory controller, spi command interface Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 16/17] bootm command: added argument to arch_preboot_os, function may depend on OS type Daniel Hellstrom
` (3 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
cpu/leon3/prom.c | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/cpu/leon3/prom.c b/cpu/leon3/prom.c
index 86376bb..6cd2281 100644
--- a/cpu/leon3/prom.c
+++ b/cpu/leon3/prom.c
@@ -1059,6 +1059,22 @@ void srmmu_init_cpu(unsigned int entry)
((CONFIG_SYS_SDRAM_BASE + 0x6000000) >> 4) | ACC_SU_ALL | PTE;
psrmmu_tables->pgd_table[0xf7] =
((CONFIG_SYS_SDRAM_BASE + 0x7000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xf8] =
+ ((CONFIG_SYS_SDRAM_BASE + 0x8000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xf9] =
+ ((CONFIG_SYS_SDRAM_BASE + 0x9000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xfa] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xa000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xfb] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xb000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xfc] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xc000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xfd] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xd000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xfe] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xe000000) >> 4) | ACC_SU_ALL | PTE;
+ psrmmu_tables->pgd_table[0xff] =
+ ((CONFIG_SYS_SDRAM_BASE + 0xf000000) >> 4) | ACC_SU_ALL | PTE;
/* convert rom vec pointer to virtual address */
kernel_arg_promvec = (struct linux_romvec *)
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 16/17] bootm command: added argument to arch_preboot_os, function may depend on OS type.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (13 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 15/17] LEON3: fixed MMU table for systems with larger memory than 128MB Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 17/17] SPARC, LEON3: added support for multiprocessing, tested Linux 2.6.21.1 SMP and RTEMS-4.10 AMP Daniel Hellstrom
` (2 subsequent siblings)
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
common/cmd_bootm.c | 8 ++++----
cpu/mpc85xx/cpu_init.c | 2 +-
2 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/common/cmd_bootm.c b/common/cmd_bootm.c
index 94ddac3..f795857 100644
--- a/common/cmd_bootm.c
+++ b/common/cmd_bootm.c
@@ -170,11 +170,11 @@ void __arch_lmb_reserve(struct lmb *lmb)
void arch_lmb_reserve(struct lmb *lmb) __attribute__((weak, alias("__arch_lmb_reserve")));
/* Allow for arch specific config before we boot */
-void __arch_preboot_os(void)
+void __arch_preboot_os(int os)
{
/* please define platform specific arch_preboot_os() */
}
-void arch_preboot_os(void) __attribute__((weak, alias("__arch_preboot_os")));
+void arch_preboot_os(int os) __attribute__((weak, alias("__arch_preboot_os")));
#if defined(__ARM__)
#define IH_INITRD_ARCH IH_ARCH_ARM
@@ -571,7 +571,7 @@ int do_bootm_subcommand (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
break;
case BOOTM_STATE_OS_GO:
disable_interrupts();
- arch_preboot_os();
+ arch_preboot_os(images.os.os);
boot_fn(BOOTM_STATE_OS_GO, argc, argv, &images);
break;
}
@@ -704,7 +704,7 @@ int do_bootm (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
return 1;
}
- arch_preboot_os();
+ arch_preboot_os(images.os.os);
boot_fn(0, argc, argv, &images);
diff --git a/cpu/mpc85xx/cpu_init.c b/cpu/mpc85xx/cpu_init.c
index 0041a60..100f8f4 100644
--- a/cpu/mpc85xx/cpu_init.c
+++ b/cpu/mpc85xx/cpu_init.c
@@ -382,7 +382,7 @@ int cpu_init_r(void)
extern void setup_ivors(void);
-void arch_preboot_os(void)
+void arch_preboot_os(int os)
{
u32 msr;
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 17/17] SPARC, LEON3: added support for multiprocessing, tested Linux 2.6.21.1 SMP and RTEMS-4.10 AMP.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (14 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 16/17] bootm command: added argument to arch_preboot_os, function may depend on OS type Daniel Hellstrom
@ 2010-01-28 12:16 ` Daniel Hellstrom
2010-01-28 20:41 ` [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Mike Frysinger
2010-05-05 21:35 ` Wolfgang Denk
17 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-01-28 12:16 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
board/gaisler/gr_cpci_ax2000/u-boot.lds | 7 ++
board/gaisler/gr_ep2s60/u-boot.lds | 7 ++
board/gaisler/gr_xc3s_1500/u-boot.lds | 7 ++
board/gaisler/grsim/u-boot.lds | 7 ++
cpu/leon3/Makefile | 2 +-
cpu/leon3/cpu.c | 10 ++-
cpu/leon3/cpu_mp.c | 80 ++++++++++++++
cpu/leon3/prom.c | 32 +++---
cpu/leon3/start.S | 70 ++++++++++++
include/asm-sparc/boot_mp.h | 70 ++++++++++++
include/configs/gr_cpci_ax2000.h | 12 ++-
include/configs/gr_ep2s60.h | 12 ++-
include/configs/gr_xc3s_1500.h | 14 ++-
include/configs/grsim.h | 12 ++-
lib_sparc/Makefile | 2 +-
lib_sparc/boot_mp.c | 177 +++++++++++++++++++++++++++++++
lib_sparc/bootm.c | 57 ++++++++--
17 files changed, 540 insertions(+), 38 deletions(-)
create mode 100644 cpu/leon3/cpu_mp.c
create mode 100644 include/asm-sparc/boot_mp.h
create mode 100644 lib_sparc/boot_mp.c
diff --git a/board/gaisler/gr_cpci_ax2000/u-boot.lds b/board/gaisler/gr_cpci_ax2000/u-boot.lds
index d5d7842..17a0fc3 100644
--- a/board/gaisler/gr_cpci_ax2000/u-boot.lds
+++ b/board/gaisler/gr_cpci_ax2000/u-boot.lds
@@ -72,6 +72,13 @@ SECTIONS
*(.prom.text)
. = ALIGN(16);
__prom_end = .;
+ /* Align MP section to the same as the MAX size of the MP section */
+ . = ALIGN(512);
+ __mp_start = .;
+ *(.mp.data)
+ *(.mp.text)
+ . = ALIGN(16);
+ __mp_end = .;
*(.text)
*(.fixup)
*(.gnu.warning)
diff --git a/board/gaisler/gr_ep2s60/u-boot.lds b/board/gaisler/gr_ep2s60/u-boot.lds
index 99aa0ad..c02a6d2 100644
--- a/board/gaisler/gr_ep2s60/u-boot.lds
+++ b/board/gaisler/gr_ep2s60/u-boot.lds
@@ -72,6 +72,13 @@ SECTIONS
*(.prom.text)
. = ALIGN(16);
__prom_end = .;
+ /* Align MP section to the same as the MAX size of the MP section */
+ . = ALIGN(512);
+ __mp_start = .;
+ *(.mp.data)
+ *(.mp.text)
+ . = ALIGN(16);
+ __mp_end = .;
*(.text)
*(.fixup)
*(.gnu.warning)
diff --git a/board/gaisler/gr_xc3s_1500/u-boot.lds b/board/gaisler/gr_xc3s_1500/u-boot.lds
index 3b13190..de7ea6b 100644
--- a/board/gaisler/gr_xc3s_1500/u-boot.lds
+++ b/board/gaisler/gr_xc3s_1500/u-boot.lds
@@ -72,6 +72,13 @@ SECTIONS
*(.prom.text)
. = ALIGN(16);
__prom_end = .;
+ /* Align MP section to the same as the MAX size of the MP section */
+ . = ALIGN(512);
+ __mp_start = .;
+ *(.mp.data)
+ *(.mp.text)
+ . = ALIGN(16);
+ __mp_end = .;
*(.text)
*(.fixup)
*(.gnu.warning)
diff --git a/board/gaisler/grsim/u-boot.lds b/board/gaisler/grsim/u-boot.lds
index 0fa6627..ac7dbec 100644
--- a/board/gaisler/grsim/u-boot.lds
+++ b/board/gaisler/grsim/u-boot.lds
@@ -71,6 +71,13 @@ SECTIONS
*(.prom.text)
. = ALIGN(16);
__prom_end = .;
+ /* Align MP section to the same as the MAX size of the MP section */
+ . = ALIGN(512);
+ __mp_start = .;
+ *(.mp.data)
+ *(.mp.text)
+ . = ALIGN(16);
+ __mp_end = .;
*(.text)
*(.fixup)
*(.gnu.warning)
diff --git a/cpu/leon3/Makefile b/cpu/leon3/Makefile
index f1bb808..4d36061 100644
--- a/cpu/leon3/Makefile
+++ b/cpu/leon3/Makefile
@@ -28,7 +28,7 @@ LIB = $(obj)lib$(CPU).a
START = start.o
SOBJS = ambapp_low.o ambapp_low_c.o memcfg_low.o
COBJS = cpu_init.o serial.o cpu.o ambapp.o interrupts.o prom.o usb_uhci.o \
- memcfg.o
+ memcfg.o cpu_mp.o
SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/leon3/cpu.c b/cpu/leon3/cpu.c
index 5cc9513..13d3dd7 100644
--- a/cpu/leon3/cpu.c
+++ b/cpu/leon3/cpu.c
@@ -83,8 +83,14 @@ int checkcpu(void)
/* ------------------------------------------------------------------------- */
-void cpu_reset(void)
+int cpu_reset(int nr)
{
+ if ( nr > 0 ) {
+ puts(" CPU[N] RESET NOT SUPPORTED BY ARCHITECTURE (N>0), "
+ "SYSTEM RESET IS POSSIBLE.");
+ return -1;
+ }
+
/* Interrupts off */
disable_interrupts();
@@ -94,7 +100,7 @@ void cpu_reset(void)
int do_reset(cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
{
- cpu_reset();
+ cpu_reset(0);
return 1;
diff --git a/cpu/leon3/cpu_mp.c b/cpu/leon3/cpu_mp.c
new file mode 100644
index 0000000..5cd5a6a
--- /dev/null
+++ b/cpu/leon3/cpu_mp.c
@@ -0,0 +1,80 @@
+/* Interface implementation for cmd_mp.c on multi processor LEON
+ * CPUs
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Gaisler Research, daniel at gaisler.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+
+#ifdef CONFIG_MP
+
+#include <grlib/irqmp.h>
+
+extern int leon_cpu_cnt;
+extern ambapp_dev_irqmp *irqmp;
+
+int cpu_numcores(void)
+{
+ return leon_cpu_cnt;
+}
+
+int cpu_status(int nr)
+{
+ printf("LEON CPUs available: %d\n", leon_cpu_cnt);
+
+ return 0;
+}
+
+int cpu_release(int nr, int argc, char *argv[])
+{
+ unsigned int ep, stack, arg0, arg1;
+
+ /* Get entry point, stack and argument */
+ if ( argc < 2 ) {
+ printf( " At least 5 arguments must be given.\n"
+ " Argument 4 is entry point\n"
+ " Argument 5 is stack\n"
+ " Argument 6-7 is kernel arg 0 and 1 (OPTIONAL)\n");
+ return -1;
+ }
+ ep = simple_strtoul(argv[0], NULL, 16);
+ stack = simple_strtoul(argv[1], NULL, 16);
+ arg0 = arg1 = 0;
+
+ if ( argc > 2 ) {
+ arg0 = simple_strtoul(argv[2], NULL, 16);
+ }
+ if ( argc > 3 ) {
+ arg1 = simple_strtoul(argv[3], NULL, 16);
+ }
+
+ /* Register CPU start up options into MP table */
+ boot_mp_cpu_setup(nr, ep, stack, (void *)arg0, (void *)arg1);
+
+ /* Release CPU by writing to IRQ controller MP register */
+ irqmp->mstatus = (1<<nr);
+
+ return 0;
+}
+
+#endif
diff --git a/cpu/leon3/prom.c b/cpu/leon3/prom.c
index 6cd2281..2a4fc2d 100644
--- a/cpu/leon3/prom.c
+++ b/cpu/leon3/prom.c
@@ -31,6 +31,7 @@
#include <asm/processor.h>
#include <asm/irq.h>
#include <asm/leon.h>
+#include <asm/boot_mp.h>
#include <ambapp.h>
#include <grlib/apbuart.h>
#include <grlib/irqmp.h>
@@ -931,21 +932,9 @@ void leon_prom_init(struct leon_prom_info *pspi)
/* Set the pointer to the Console UART in romvec */
pspi->reloc_funcs.leon3_apbuart = leon3_apbuart;
- {
- int j = 1;
-#ifdef CONFIG_SMP
- ambapp_dev_irqmp *b;
- b = (ambapp_dev_irqmp *) leon3_getapbbase(VENDOR_GAISLER,
- GAISLER_IRQMP);
- if (b) {
- j = 1 + ((LEON3_BYPASS_LOAD_PA(&(b->mpstatus))
- >> LEON3_IRQMPSTATUS_CPUNR) & 0xf);
- }
-#endif
#undef nodes
- pspi->nodes[2 + j].level = -1;
- pspi->nodes[2 + j].properties = __va(spi.root_properties + 3);
- }
+ pspi->nodes[2 + leon_cpu_cnt].level = -1;
+ pspi->nodes[2 + leon_cpu_cnt].properties = __va(spi.root_properties + 3);
/* Set Ethernet MAC address from environment */
if ((addr_str = getenv("ethaddr")) != NULL) {
@@ -1024,7 +1013,7 @@ void prepare_bootargs(char *bootargs)
}
}
-void srmmu_init_cpu(unsigned int entry)
+void srmmu_init(unsigned int entry)
{
sparc_srmmu_setup *psrmmu_tables = (void *)
((((unsigned int)&srmmu_tables) & PROM_SIZE_MASK) +
@@ -1079,6 +1068,19 @@ void srmmu_init_cpu(unsigned int entry)
/* convert rom vec pointer to virtual address */
kernel_arg_promvec = (struct linux_romvec *)
(((unsigned int)kernel_arg_promvec & 0x0fffffff) | 0xf0000000);
+}
+
+#ifdef CONFIG_MP
+/* This function must be located in the MP or PROM part of the application because
+ * it will be called from CPU1, CPU2 ... after CPU0 has made it into the kernel
+ * and started the other CPUs
+ */
+void MP_TEXT boot_mp_linux_cpu_preinit(int cpu)
+#else
+void boot_mp_linux_cpu_preinit(int cpu)
+#endif
+{
+ sparc_srmmu_setup *psrmmu_tables = (void *)CONFIG_SYS_PROM_OFFSET;
/* Set Context pointer to point to context table
* 256 contexts supported.
diff --git a/cpu/leon3/start.S b/cpu/leon3/start.S
index d9faa86..1f30150 100644
--- a/cpu/leon3/start.S
+++ b/cpu/leon3/start.S
@@ -27,6 +27,7 @@
#include <asm/psr.h>
#include <asm/stack.h>
#include <asm/leon.h>
+#include <asm/boot_mp.h>
#include <timestamp.h>
#include <version.h>
#include <ambapp.h>
@@ -258,6 +259,20 @@ wininit:
set WIM_INIT, %g3
mov %g3, %wim
+#ifdef CONFIG_MP
+/* In a multi CPU system (and the slave CPUs have been started) the slaves
+ * have a special boot up sequence. It is expected that CPU0 has already run
+ * u-boot and it has loaded an OS which now have activated one or more slave
+ * CPUs.
+ */
+multi_cpu_detect:
+ rd %asr17, %g3
+ srl %g3, 28, %g3
+ cmp %g3, %g0
+ bne slave_cpu_init
+ nop
+#endif
+
stackp:
set CONFIG_SYS_INIT_SP_OFFSET, %fp
andn %fp, 0x0f, %fp
@@ -386,6 +401,23 @@ prom_relocate_loop:
bne prom_relocate_loop
inc 16,%g4
+#ifdef CONFIG_MP
+mp_relocate:
+ set __mp_start, %g2
+ set __mp_end, %g3
+ set CONFIG_SYS_MP_OFFSET, %g4
+
+mp_relocate_loop:
+ ldd [%g2],%l0
+ ldd [%g2+8],%l2
+ std %l0,[%g4]
+ std %l2,[%g4+8]
+ inc 16,%g2
+ subcc %g3,%g2,%g0
+ bne mp_relocate_loop
+ inc 16,%g4
+#endif
+
/* Trap table has been moved, lets tell CPU about
* the new trap table address
*/
@@ -651,3 +683,41 @@ _reset_reloc:
set start, %l0
call %l0
nop
+
+#ifdef CONFIG_MP
+/* Slave CPUs reach here */
+slave_cpu_init:
+
+ /* Get Index into cpu slave struct */
+ sll %g3, 4, %i0
+
+ set (CONFIG_SYS_MP_OFFSET+0x4), %o1 /* cpu_table is mp_data+0x4 */
+ add %i0, %o1, %i0
+
+ /* Setup Stack Pointer from config */
+ ld [%i0 + BOOT_MP_CPU_STACK], %fp
+ andn %fp, 0x0f, %fp
+ sub %fp, 64, %sp
+
+ /* Call OS-dependent CPU init routine */
+ set CONFIG_SYS_MP_OFFSET, %o1 /* cpu_table is mp_data+0x0 */
+ ld [%o1], %o1
+ cmp %o1, 0
+ beq slave_cpu_boot_kernel
+ nop
+ call %o1
+ clr %o0
+
+ /* Call Kernel */
+slave_cpu_boot_kernel:
+ ld [%i0 + BOOT_MP_CPU_ARG0], %o0 /* ARG0 */
+ ld [%i0 + BOOT_MP_CPU_ARG1], %o1 /* ARG1 */
+ ld [%i0 + BOOT_MP_CPU_EP], %o3 /* ENTRY POINT */
+ call %o3
+ clr %o2
+
+dead_slave:
+ /* Kernel Failed or no support for MP */
+ ta 0x1
+ nop
+#endif
diff --git a/include/asm-sparc/boot_mp.h b/include/asm-sparc/boot_mp.h
new file mode 100644
index 0000000..e033b9c
--- /dev/null
+++ b/include/asm-sparc/boot_mp.h
@@ -0,0 +1,70 @@
+/* Multiprocessor boot setup functions.
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Gaisler Research, daniel at gaisler.com.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#ifndef __ASM_SPARC_BOOT_MP_H__
+#define __ASM_SPARC_BOOT_MP_H__
+
+#define MP_TEXT __attribute__ ((__section__ (".mp.text")))
+#define MP_DATA __attribute__ ((__section__ (".mp.data")))
+
+#define BOOT_MP_CPU_EP 0x00
+#define BOOT_MP_CPU_STACK 0x04
+#define BOOT_MP_CPU_ARG0 0x08
+#define BOOT_MP_CPU_ARG1 0x0C
+
+#ifndef __ASSEMBLER__
+
+/* Allow for arch specific CPU initialization before RTEMS boot */
+extern void boot_mp_rtems_cpu_preinit(int cpu);
+
+/* Allow for arch specific CPU initialization before VxWorks boot */
+extern void boot_mp_vxworks_cpu_preinit(int cpu);
+
+/* Allow for arch specific CPU initialization before Linux boot */
+extern void boot_mp_linux_cpu_preinit(int cpu);
+
+struct boot_mp_cpu {
+ unsigned int entry_point;
+ unsigned int stack;
+ void *arg0;
+ void *arg1;
+};
+
+/* All CPU entry points and stacks */
+extern struct boot_mp_cpu boot_mp_cpu_table[];
+
+extern void boot_mp_os_setup(int os);
+
+extern void boot_mp_cpu_setup(
+ int cpu,
+ unsigned int entry_point,
+ unsigned int stack,
+ void *arg0,
+ void *arg1
+ );
+
+/* Init a CPU before entering the kernel */
+extern void boot_mp_cpu_preinit(int cpu);
+
+#endif
+
+#endif
diff --git a/include/configs/gr_cpci_ax2000.h b/include/configs/gr_cpci_ax2000.h
index b9d45dd..a6d669d 100644
--- a/include/configs/gr_cpci_ax2000.h
+++ b/include/configs/gr_cpci_ax2000.h
@@ -264,8 +264,16 @@
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
+#ifdef CONFIG_MP
+#define CONFIG_SYS_MP_SIZE 512
+#define CONFIG_SYS_MP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_MP_SIZE)
+#else
+#define CONFIG_SYS_MP_SIZE 0
+#define CONFIG_SYS_MP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#endif
+
+#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_MP_SIZE-CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_MP_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
diff --git a/include/configs/gr_ep2s60.h b/include/configs/gr_ep2s60.h
index 6edb92c..10afca2 100644
--- a/include/configs/gr_ep2s60.h
+++ b/include/configs/gr_ep2s60.h
@@ -232,8 +232,16 @@
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
+#ifdef CONFIG_MP
+#define CONFIG_SYS_MP_SIZE 512
+#define CONFIG_SYS_MP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_MP_SIZE)
+#else
+#define CONFIG_SYS_MP_SIZE 0
+#define CONFIG_SYS_MP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#endif
+
+#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_MP_SIZE-CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_MP_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
diff --git a/include/configs/gr_xc3s_1500.h b/include/configs/gr_xc3s_1500.h
index 1f9dd4a..b57640a 100644
--- a/include/configs/gr_xc3s_1500.h
+++ b/include/configs/gr_xc3s_1500.h
@@ -54,6 +54,8 @@
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION
+#define CONFIG_MP
+#define CONFIG_MP_MAX_CPUS 4
/*
* Supported commands
@@ -209,8 +211,16 @@
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
+#ifdef CONFIG_MP
+#define CONFIG_SYS_MP_SIZE 512
+#define CONFIG_SYS_MP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_MP_SIZE)
+#else
+#define CONFIG_SYS_MP_SIZE 0
+#define CONFIG_SYS_MP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#endif
+
+#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_MP_SIZE-CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_MP_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
diff --git a/include/configs/grsim.h b/include/configs/grsim.h
index f815672..9e177e6 100644
--- a/include/configs/grsim.h
+++ b/include/configs/grsim.h
@@ -234,8 +234,16 @@
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
+#ifdef CONFIG_MP
+#define CONFIG_SYS_MP_SIZE 512
+#define CONFIG_SYS_MP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_MP_SIZE)
+#else
+#define CONFIG_SYS_MP_SIZE 0
+#define CONFIG_SYS_MP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#endif
+
+#define CONFIG_SYS_PROM_SIZE (8192-CONFIG_SYS_MP_SIZE-CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_MP_OFFSET-CONFIG_SYS_PROM_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE (0x10000-32)
diff --git a/lib_sparc/Makefile b/lib_sparc/Makefile
index 040ca10..3860fdc 100644
--- a/lib_sparc/Makefile
+++ b/lib_sparc/Makefile
@@ -27,7 +27,7 @@ LIB = $(obj)lib$(ARCH).a
SOBJS =
-COBJS = board.o cache.o interrupts.o time.o bootm.o
+COBJS = board.o cache.o interrupts.o time.o bootm.o boot_mp.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/lib_sparc/boot_mp.c b/lib_sparc/boot_mp.c
new file mode 100644
index 0000000..3154fd1
--- /dev/null
+++ b/lib_sparc/boot_mp.c
@@ -0,0 +1,177 @@
+/* SPARC Multi-Processor initialization
+ *
+ * (C) Copyright 2010
+ * Daniel Hellstrom, Aeroflex Gaisler, daniel at gaisler.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/boot_mp.h>
+#include <config.h>
+
+#ifdef CONFIG_MP
+
+#ifndef CONFIG_MP_MAX_CPUS
+ #error CONFIG_MP_MAX_CPUS must be defined
+#endif
+
+typedef int (*cpu_preinit_func) (int cpu);
+
+/* Structure of all MP DATA section */
+struct boot_mp_data {
+ /* Function called for each CPU before entering kernel */
+ cpu_preinit_func func;
+
+ /* All CPU entry points and so on */
+ struct boot_mp_cpu cpu_table[CONFIG_MP_MAX_CPUS];
+
+ /* OS to boot */
+ int os;
+};
+
+struct boot_mp_data MP_DATA mp_data;
+
+/* Allow for specific RTEMS CPU initialization before RTEMS AMP boot */
+void MP_TEXT __boot_mp_rtems_cpu_preinit(int cpu)
+{
+
+}
+void boot_mp_rtems_cpu_preinit(int cpu)
+ __attribute__((weak, alias("__boot_mp_rtems_cpu_preinit")));
+
+/* Allow for specific VxWorks CPU initialization before slave CPUs boot */
+void MP_TEXT __boot_mp_vxworks_cpu_preinit(int cpu)
+{
+
+}
+void boot_mp_vxworks_cpu_preinit(int cpu)
+ __attribute__((weak, alias("__boot_mp_vxworks_cpu_preinit")));
+
+/* Allow for specific Linux CPU initialization before slave CPUs boot */
+void MP_TEXT __boot_mp_linux_cpu_preinit(int cpu)
+{
+
+}
+void boot_mp_linux_cpu_preinit(int cpu)
+ __attribute__((weak, alias("__boot_mp_linux_cpu_preinit")));
+
+static cpu_preinit_func os_cpu_preinit[] =
+{
+ [IH_OS_LINUX] = boot_mp_linux_cpu_preinit,
+ [IH_OS_RTEMS] = boot_mp_rtems_cpu_preinit,
+ [IH_OS_VXWORKS] = boot_mp_vxworks_cpu_preinit,
+};
+
+void boot_mp_os_setup(int os)
+{
+ struct boot_mp_data *mpd = (void *)CONFIG_SYS_MP_OFFSET;
+ unsigned int func;
+
+ mpd->os = os;
+
+ func = (unsigned int)os_cpu_preinit[os];
+ if ( func == 0 ) {
+ /* We assume that the OS booting does not support MP and will
+ * therefore not start the other CPUs.
+ */
+ mpd->func = 0;
+ } else {
+ mpd->func = CONFIG_SYS_MP_OFFSET + (func & (CONFIG_SYS_MP_SIZE-1));
+ }
+
+ debug("boot_mp_os_setup: 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x\n",
+ os,
+ os_cpu_preinit,
+ &os_cpu_preinit[os],
+ (unsigned int)os_cpu_preinit[os],
+ CONFIG_SYS_MP_SIZE,
+ ((unsigned int)os_cpu_preinit[os] & (CONFIG_SYS_MP_SIZE-1))
+ );
+}
+
+void boot_mp_cpu_setup(
+ int cpu,
+ unsigned int entry_point,
+ unsigned int stack,
+ void *arg0,
+ void *arg1
+ )
+{
+ struct boot_mp_data *mpd = (void *)CONFIG_SYS_MP_OFFSET;
+
+ if ( cpu >= CONFIG_MP_MAX_CPUS )
+ return;
+
+ mpd->cpu_table[cpu].entry_point = entry_point;
+ mpd->cpu_table[cpu].stack = stack;
+ mpd->cpu_table[cpu].arg0 = arg0;
+ mpd->cpu_table[cpu].arg1 = arg1;
+
+ debug("boot_mp_cpu_setup(%d): ep=0x%x stack=0x%x, arg=[0x%x,0x%x]\n",
+ cpu, entry_point, stack, arg0, arg1);
+}
+
+/* In a RTEMS AMP system all CPUs have different entry points and stacks,
+ * the addresses are taken from the environment variables:
+ * cpu0_entry and cpu0_stack
+ */
+void boot_mp_rtems_setup(void)
+{
+ char *str;
+ char env_str[16];
+ int cpu;
+ unsigned int entry, stack;
+
+ for(cpu=0; cpu<CONFIG_MP_MAX_CPUS; cpu++) {
+
+ entry = 0;
+ stack = 0;
+
+ strcpy(env_str, "cpuX_entry");
+ env_str[3] = '0' + cpu;
+ if ( (str = getenv(env_str)) != NULL ) {
+ entry = simple_strtoul(str, NULL, 16);
+ }
+
+ strcpy(env_str, "cpuX_stack");
+ env_str[3] = '0' + cpu;
+ if ( (str = getenv(env_str)) != NULL ) {
+ stack = simple_strtoul(str, NULL, 16);
+ }
+
+ boot_mp_cpu_setup(
+ cpu,
+ (unsigned int)entry,
+ (unsigned int)stack,
+ NULL,
+ NULL);
+ }
+}
+
+/* Prepare boot, called from bootm */
+void arch_preboot_os(int os)
+{
+ boot_mp_os_setup(os);
+
+ if ( os == IH_OS_RTEMS )
+ boot_mp_rtems_setup();
+}
+
+#endif
diff --git a/lib_sparc/bootm.c b/lib_sparc/bootm.c
index f517325..428ad97 100644
--- a/lib_sparc/bootm.c
+++ b/lib_sparc/bootm.c
@@ -28,11 +28,12 @@
#include <asm/prom.h>
#include <asm/cache.h>
#include <image.h>
+#include <asm-sparc/boot_mp.h>
#define PRINT_KERNEL_HEADER
extern image_header_t header;
-extern void srmmu_init_cpu(unsigned int entry);
+extern void srmmu_init(unsigned int entry);
extern void prepare_bootargs(char *bootargs);
/* sparc kernel argument (the ROM vector) */
@@ -43,7 +44,8 @@ struct linux_romvec *kernel_arg_promvec;
#define RAMDISK_IMAGE_START_MASK 0x07FF
#define RAMDISK_PROMPT_FLAG 0x8000
#define RAMDISK_LOAD_FLAG 0x4000
-struct __attribute__ ((packed)) {
+/* Linux Single CPU Header */
+struct linux_up_hdr {
char traptable[PAGE_SIZE];
char swapper_pg_dir[PAGE_SIZE];
char pg0[PAGE_SIZE];
@@ -73,7 +75,13 @@ struct __attribute__ ((packed)) {
unsigned int end;
} ver_0203;
} hdr_input;
-} *linux_hdr;
+} __attribute__ ((packed)) ;
+
+/* Linux SMP Header */
+struct linux_smp_hdr {
+ char traptable[3][PAGE_SIZE];
+ struct linux_up_hdr single_hdr;
+} __attribute__ ((packed));
/* temporary initrd image holder */
image_header_t ihdr;
@@ -98,23 +106,34 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t * images)
void (*kernel) (struct linux_romvec *, void *);
struct lmb *lmb = &images->lmb;
int ret;
+ int i;
+ struct linux_up_hdr *linux_hdr;
+ struct linux_smp_hdr *linux_smp_hdr;
if ((flag != 0) && (flag != BOOTM_STATE_OS_GO))
return 1;
- /* Get virtual address of kernel start */
- linux_hdr = (void *)images->os.load;
-
- /* */
+ /* Kernel Entry Point */
kernel = (void (*)(struct linux_romvec *, void *))images->ep;
+ /* Get virtual address of kernel start */
+ linux_hdr = (struct linux_up_hdr *)images->os.load;
+
/* check for a SPARC kernel */
if ((linux_hdr->hdr[0] != 'H') ||
(linux_hdr->hdr[1] != 'd') ||
(linux_hdr->hdr[2] != 'r') || (linux_hdr->hdr[3] != 'S')) {
- puts("Error reading header of SPARC Linux kernel, aborting\n");
- goto error;
+ /* Not a valid Linux Header, check if Linux SMP header */
+ linux_smp_hdr = (struct linux_smp_hdr *)images->os.load;
+ linux_hdr = (struct linux_up_hdr *)&linux_smp_hdr->single_hdr;
+ if ((linux_hdr->hdr[0] != 'H') ||
+ (linux_hdr->hdr[1] != 'd') ||
+ (linux_hdr->hdr[2] != 'r') || (linux_hdr->hdr[3] != 'S')) {
+ puts("Error reading header of SPARC Linux kernel, aborting\n");
+ goto error;
+ }
}
+
#ifdef PRINT_KERNEL_HEADER
printf("## Found SPARC Linux kernel %d.%d.%d ...\n",
linux_hdr->linuxver_major,
@@ -164,8 +183,24 @@ int do_bootm_linux(int flag, int argc, char *argv[], bootm_headers_t * images)
bootargs = getenv("bootargs");
prepare_bootargs(bootargs);
- /* turn on mmu & setup context table & page table for process 0 (kernel) */
- srmmu_init_cpu((unsigned int)kernel);
+ /* Init MMU table of SRMMU and more */
+ srmmu_init((unsigned int)kernel);
+
+#ifdef CONFIG_MP
+ for(i=0; i<CONFIG_MP_MAX_CPUS; i++) {
+ boot_mp_cpu_setup(
+ i,
+ (unsigned int)kernel,
+ (unsigned int)CONFIG_SYS_INIT_SP_OFFSET,
+ kernel_arg_promvec,
+ NULL);
+ }
+#endif
+
+ /* turn on mmu & setup context table & page table for process 0 (kernel).
+ * This function is later called by each CPU in a multiprocessor system.
+ */
+ boot_mp_linux_cpu_preinit(0);
/* Enter SPARC Linux kernel
* From now on the only code in u-boot that will be
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (15 preceding siblings ...)
2010-01-28 12:16 ` [U-Boot] [PATCH 17/17] SPARC, LEON3: added support for multiprocessing, tested Linux 2.6.21.1 SMP and RTEMS-4.10 AMP Daniel Hellstrom
@ 2010-01-28 20:41 ` Mike Frysinger
2010-02-01 17:08 ` Daniel Hellstrom
2010-05-05 21:35 ` Wolfgang Denk
17 siblings, 1 reply; 26+ messages in thread
From: Mike Frysinger @ 2010-01-28 20:41 UTC (permalink / raw)
To: u-boot
On Thursday 28 January 2010 07:16:20 Daniel Hellstrom wrote:
> Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
> ---
> include/asm-sparc/unaligned.h | 17 +++++++++++++++++
> 1 files changed, 17 insertions(+), 0 deletions(-)
> create mode 100644 include/asm-sparc/unaligned.h
>
> diff --git a/include/asm-sparc/unaligned.h b/include/asm-sparc/unaligned.h
> new file mode 100644
> index 0000000..4e604c1
> --- /dev/null
> +++ b/include/asm-sparc/unaligned.h
> @@ -0,0 +1,17 @@
> +#ifndef _ASM_SPARC_UNALIGNED_H
> +#define _ASM_SPARC_UNALIGNED_H
> +
> +#ifdef __KERNEL__
> +
> +/*
> + * The SPARC can not do unaligned accesses, it must be split into multiple
> + * byte accesses. The SPARC is in big endian mode.
> + */
> +#include <linux/unaligned/be_byteshift.h>
> +#include <linux/unaligned/generic.h>
> +
> +#define get_unaligned __get_unaligned_be
> +#define put_unaligned __put_unaligned_be
> +
> +#endif /* __KERNEL__ */
> +#endif /* _ASM_SPARC_UNALIGNED_H */
there is a proposed asm-generic/unaligned.h on the mailing list which i think
you could use. you'd just need:
#include <asm-generic/unaligned.h>
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100128/329f0c76/attachment.pgp
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-01-28 20:41 ` [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Mike Frysinger
@ 2010-02-01 17:08 ` Daniel Hellstrom
2010-03-16 20:44 ` Mike Frysinger
0 siblings, 1 reply; 26+ messages in thread
From: Daniel Hellstrom @ 2010-02-01 17:08 UTC (permalink / raw)
To: u-boot
Mike Frysinger wrote:
>On Thursday 28 January 2010 07:16:20 Daniel Hellstrom wrote:
>
>
>>Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
>>---
>> include/asm-sparc/unaligned.h | 17 +++++++++++++++++
>> 1 files changed, 17 insertions(+), 0 deletions(-)
>> create mode 100644 include/asm-sparc/unaligned.h
>>
>>diff --git a/include/asm-sparc/unaligned.h b/include/asm-sparc/unaligned.h
>>new file mode 100644
>>index 0000000..4e604c1
>>--- /dev/null
>>+++ b/include/asm-sparc/unaligned.h
>>@@ -0,0 +1,17 @@
>>+#ifndef _ASM_SPARC_UNALIGNED_H
>>+#define _ASM_SPARC_UNALIGNED_H
>>+
>>+#ifdef __KERNEL__
>>+
>>+/*
>>+ * The SPARC can not do unaligned accesses, it must be split into multiple
>>+ * byte accesses. The SPARC is in big endian mode.
>>+ */
>>+#include <linux/unaligned/be_byteshift.h>
>>+#include <linux/unaligned/generic.h>
>>+
>>+#define get_unaligned __get_unaligned_be
>>+#define put_unaligned __put_unaligned_be
>>+
>>+#endif /* __KERNEL__ */
>>+#endif /* _ASM_SPARC_UNALIGNED_H */
>>
>>
>
>there is a proposed asm-generic/unaligned.h on the mailing list which i think
>you could use. you'd just need:
>#include <asm-generic/unaligned.h>
>-mike
>
>
Thank you for your comment, I will update this patch.
Daniel
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-02-01 17:08 ` Daniel Hellstrom
@ 2010-03-16 20:44 ` Mike Frysinger
0 siblings, 0 replies; 26+ messages in thread
From: Mike Frysinger @ 2010-03-16 20:44 UTC (permalink / raw)
To: u-boot
On Monday 01 February 2010 12:08:51 Daniel Hellstrom wrote:
> Mike Frysinger wrote:
> >there is a proposed asm-generic/unaligned.h on the mailing list which i
> >think you could use. you'd just need:
> >#include <asm-generic/unaligned.h>
>
> Thank you for your comment, I will update this patch.
the generic unaligned.h has been merged if you want to post your one-line
patch now ...
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100316/e8073a90/attachment.pgp
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
` (16 preceding siblings ...)
2010-01-28 20:41 ` [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Mike Frysinger
@ 2010-05-05 21:35 ` Wolfgang Denk
2010-05-06 6:37 ` Daniel Hellstrom
17 siblings, 1 reply; 26+ messages in thread
From: Wolfgang Denk @ 2010-05-05 21:35 UTC (permalink / raw)
To: u-boot
Dear Daniel Hellstrom,
In message <1264680996-13804-1-git-send-email-daniel@gaisler.com> you wrote:
> Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
> ---
> include/asm-sparc/unaligned.h | 17 +++++++++++++++++
> 1 files changed, 17 insertions(+), 0 deletions(-)
> create mode 100644 include/asm-sparc/unaligned.h
This whole patch series has been out there for many months, but I'm
still waiting for a pull request from you.
Do you have any such plans?
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Sorry, but my karma just ran over your dogma.
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-05-05 21:35 ` Wolfgang Denk
@ 2010-05-06 6:37 ` Daniel Hellstrom
2010-05-06 10:57 ` Wolfgang Denk
0 siblings, 1 reply; 26+ messages in thread
From: Daniel Hellstrom @ 2010-05-06 6:37 UTC (permalink / raw)
To: u-boot
Dear Wolfgang,
I had some minor remarks on patch 1 and 2 as I recall, and a minor
change on another patch I discovered myself. Unfortunately I have been
very busy, I am really sorry for that. I will try to pull my self
together and finish them in the weekend.
Do I have to repost the patches, now that they are so delayed?
Thank you for your interest, that really helps,
Daniel Hellstrom
Wolfgang Denk wrote:
>Dear Daniel Hellstrom,
>
>In message <1264680996-13804-1-git-send-email-daniel@gaisler.com> you wrote:
>
>
>>Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
>>---
>> include/asm-sparc/unaligned.h | 17 +++++++++++++++++
>> 1 files changed, 17 insertions(+), 0 deletions(-)
>> create mode 100644 include/asm-sparc/unaligned.h
>>
>>
>
>This whole patch series has been out there for many months, but I'm
>still waiting for a pull request from you.
>
>Do you have any such plans?
>
>Best regards,
>
>Wolfgang Denk
>
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-05-06 6:37 ` Daniel Hellstrom
@ 2010-05-06 10:57 ` Wolfgang Denk
0 siblings, 0 replies; 26+ messages in thread
From: Wolfgang Denk @ 2010-05-06 10:57 UTC (permalink / raw)
To: u-boot
Dear Daniel Hellstrom,
In message <4BE263AD.7020006@gaisler.com> you wrote:
>
> I had some minor remarks on patch 1 and 2 as I recall, and a minor
> change on another patch I discovered myself. Unfortunately I have been
> very busy, I am really sorry for that. I will try to pull my self
> together and finish them in the weekend.
>
> Do I have to repost the patches, now that they are so delayed?
You will probably have to rebase these anyway, so please also repost.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"A fractal is by definition a set for which the Hausdorff Besicovitch
dimension strictly exceeds the topological dimension."
- Mandelbrot, _The Fractal Geometry of Nature_
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-05-19 22:01 ` Mike Frysinger
@ 2010-05-26 11:29 ` Daniel Hellstrom
0 siblings, 0 replies; 26+ messages in thread
From: Daniel Hellstrom @ 2010-05-26 11:29 UTC (permalink / raw)
To: u-boot
Hi,
Thank you for the input, I will resend the patch with Magnus as author.
Daniel
Mike Frysinger wrote:
>the subject line is incorrect. you dont credit people via summary/changelogs,
>you do it via the tags. so if Magnus wrote this patch, he should be credited
>with authorship (so use --author when committing). if he gave tips or
>something, then perhaps use Reported-by.
>-mike
>
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
2010-05-18 14:47 Daniel Hellstrom
@ 2010-05-19 22:01 ` Mike Frysinger
2010-05-26 11:29 ` Daniel Hellstrom
0 siblings, 1 reply; 26+ messages in thread
From: Mike Frysinger @ 2010-05-19 22:01 UTC (permalink / raw)
To: u-boot
the subject line is incorrect. you dont credit people via summary/changelogs,
you do it via the tags. so if Magnus wrote this patch, he should be credited
with authorship (so use --author when committing). if he gave tips or
something, then perhaps use Reported-by.
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
Url : http://lists.denx.de/pipermail/u-boot/attachments/20100519/89a69174/attachment.pgp
^ permalink raw reply [flat|nested] 26+ messages in thread
* [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander.
@ 2010-05-18 14:47 Daniel Hellstrom
2010-05-19 22:01 ` Mike Frysinger
0 siblings, 1 reply; 26+ messages in thread
From: Daniel Hellstrom @ 2010-05-18 14:47 UTC (permalink / raw)
To: u-boot
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
---
arch/sparc/include/asm/byteorder.h | 1 +
arch/sparc/include/asm/unaligned.h | 10 ++++++++++
2 files changed, 11 insertions(+), 0 deletions(-)
create mode 100644 arch/sparc/include/asm/unaligned.h
diff --git a/arch/sparc/include/asm/byteorder.h b/arch/sparc/include/asm/byteorder.h
index b9fc656..e3b3dec 100644
--- a/arch/sparc/include/asm/byteorder.h
+++ b/arch/sparc/include/asm/byteorder.h
@@ -32,6 +32,7 @@
#if defined(__GNUC__) && !defined(__STRICT_ANSI__)
#define __BYTEORDER_HAS_U64__
+#define __SWAB_64_THRU_32__
#endif
#include <linux/byteorder/big_endian.h>
#endif /* _SPARC_BYTEORDER_H */
diff --git a/arch/sparc/include/asm/unaligned.h b/arch/sparc/include/asm/unaligned.h
new file mode 100644
index 0000000..0e646f7
--- /dev/null
+++ b/arch/sparc/include/asm/unaligned.h
@@ -0,0 +1,10 @@
+#ifndef _ASM_SPARC_UNALIGNED_H
+#define _ASM_SPARC_UNALIGNED_H
+
+/*
+ * The SPARC can not do unaligned accesses, it must be split into multiple
+ * byte accesses. The SPARC is in big endian mode.
+ */
+#include <asm-generic/unaligned.h>
+
+#endif /* _ASM_SPARC_UNALIGNED_H */
--
1.5.4
^ permalink raw reply related [flat|nested] 26+ messages in thread
end of thread, other threads:[~2010-05-26 11:29 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-01-28 12:16 [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 02/17] GRETH: Added support for selecting PHY address from config, PHY address was always set to zero before Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 03/17] GRETH: Added extra RESET, this is needed if GRETH was stopped during an ethernet frame reception Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 04/17] LEON3: reimplemented AMBA Plug&Play scanning routines Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 05/17] LEON3: added memory controller initialization using the new AMBA PnP routines Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 06/17] LEON3: Moved GRLIB core header files to common include/grlib directory Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 07/17] LEON3: serial baud rate register support multiple buses with different frequency Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 08/17] SPARC: added function that checks if IRQ is on or off Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 09/17] LEON3: added busy wait function, made wait_ms() work when IRQ is disabled Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 10/17] LEON3: added CPU count and frequency detection Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 11/17] SPARC: removed USB stop from linux bootm, arch-independent bootm stop USB Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 12/17] SPARC: added optional cpu_late_init routine Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 13/17] LEON3: Added GRETH EDCL debug link IP address initialization Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 14/17] LEON: added support for GRLIB SPI Memory controller, spi command interface Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 15/17] LEON3: fixed MMU table for systems with larger memory than 128MB Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 16/17] bootm command: added argument to arch_preboot_os, function may depend on OS type Daniel Hellstrom
2010-01-28 12:16 ` [U-Boot] [PATCH 17/17] SPARC, LEON3: added support for multiprocessing, tested Linux 2.6.21.1 SMP and RTEMS-4.10 AMP Daniel Hellstrom
2010-01-28 20:41 ` [U-Boot] [PATCH 01/17] SPARC: added unaligned definitions, patch supplied by Magnus Sjalander Mike Frysinger
2010-02-01 17:08 ` Daniel Hellstrom
2010-03-16 20:44 ` Mike Frysinger
2010-05-05 21:35 ` Wolfgang Denk
2010-05-06 6:37 ` Daniel Hellstrom
2010-05-06 10:57 ` Wolfgang Denk
2010-05-18 14:47 Daniel Hellstrom
2010-05-19 22:01 ` Mike Frysinger
2010-05-26 11:29 ` Daniel Hellstrom
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.