[PATCHv2 00/11] Multiple fixes for Devkit8000

[PATCHv2 00/11] Multiple fixes for Devkit8000

[Thomas Weber]

These patches correct errors that were done while using the board code
from beagle board for Devkit8000. 

The Devkit8000 uses the TPS65930, an reduced version of the TWL4030. 
So not all power supplies from the TWL4030 are available.
The DSS2 do not need a VDVI any longer so it is removed. 
The definition of the supplies are changed to use the new REGULATOR_SUPPLY macro.
The pins for lcd and dvi powerdown are corrected.

Changes to v1:
 -remove the patches that only fix comments
 -expand the description of the patches

Kan-Ru Chen (2):
  OMAP2: Devkit8000: Enable DVI-D output
  OMAP2: Devkit8000: Setup LCD reset

Thomas Weber (9):
  OMAP2: Devkit8000: Cleanup for power supplies
  OMAP2: Devkit8000: change panel to generic panel
  OMAP2: Devkit8000: Remove unneeded VDVI supply
  OMAP2: Devkit8000: Remove non existing vsim supply
  OMAP2: Devkit8000: Remove en-/disable for tv panel
  OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro
  OMAP2: Devkit8000: Using gpio_is_valid macro
  OMAP2: Devkit8000: Remove unused omap_board_config
  OMAP2: Devkit8000: Fix regulator for power supply

 arch/arm/mach-omap2/board-devkit8000.c |  122 +++++++++++++++-----------------
 1 files changed, 58 insertions(+), 64 deletions(-)

[PATCHv2 00/11] Multiple fixes for Devkit8000

[Thomas Weber]

These patches correct errors that were done while using the board code
from beagle board for Devkit8000. 

The Devkit8000 uses the TPS65930, an reduced version of the TWL4030. 
So not all power supplies from the TWL4030 are available.
The DSS2 do not need a VDVI any longer so it is removed. 
The definition of the supplies are changed to use the new REGULATOR_SUPPLY macro.
The pins for lcd and dvi powerdown are corrected.

Changes to v1:
 -remove the patches that only fix comments
 -expand the description of the patches

Kan-Ru Chen (2):
  OMAP2: Devkit8000: Enable DVI-D output
  OMAP2: Devkit8000: Setup LCD reset

Thomas Weber (9):
  OMAP2: Devkit8000: Cleanup for power supplies
  OMAP2: Devkit8000: change panel to generic panel
  OMAP2: Devkit8000: Remove unneeded VDVI supply
  OMAP2: Devkit8000: Remove non existing vsim supply
  OMAP2: Devkit8000: Remove en-/disable for tv panel
  OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro
  OMAP2: Devkit8000: Using gpio_is_valid macro
  OMAP2: Devkit8000: Remove unused omap_board_config
  OMAP2: Devkit8000: Fix regulator for power supply

 arch/arm/mach-omap2/board-devkit8000.c |  122 +++++++++++++++-----------------
 1 files changed, 58 insertions(+), 64 deletions(-)

[PATCHv2 01/11] OMAP2: Devkit8000: Cleanup for power supplies

[Thomas Weber]

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   32 ++++++++++++++++++++++++++------
 1 files changed, 26 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 922b746..08a2a01 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,6 +168,10 @@ static struct regulator_consumer_supply devkit8000_vsim_supply = {
 	.supply			= "vmmc_aux",
 };
 
+/* ads7846 on SPI */
+static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
+	REGULATOR_SUPPLY("vcc", "spi2.0")
+};
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -282,7 +286,7 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll2_supplies[] = {
+static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
 	.supply		= "vdvi",
 	.dev		= &devkit8000_lcd_device.dev,
@@ -337,8 +341,8 @@ static struct regulator_init_data devkit8000_vdac = {
 	.consumer_supplies	= &devkit8000_vdda_dac_supply,
 };
 
-/* VPLL2 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll2 = {
+/* VPLL1 for digital video outputs */
+static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
 		.name			= "VDVI",
 		.min_uV			= 1800000,
@@ -348,8 +352,23 @@ static struct regulator_init_data devkit8000_vpll2 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll2_supplies),
-	.consumer_supplies	= devkit8000_vpll2_supplies,
+	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
+	.consumer_supplies	= devkit8000_vpll1_supplies,
+};
+
+/* VAUX4 for ads7846 and nubs */
+static struct regulator_init_data devkit8000_vio = {
+	.constraints = {
+		.min_uV                 = 1800000,
+		.max_uV                 = 1800000,
+		.apply_uV               = true,
+		.valid_modes_mask       = REGULATOR_MODE_NORMAL
+			| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask         = REGULATOR_CHANGE_MODE
+			| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
+	.consumer_supplies      = devkit8000_vio_supplies,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
@@ -376,7 +395,8 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.vmmc1		= &devkit8000_vmmc1,
 	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
-	.vpll2		= &devkit8000_vpll2,
+	.vpll1		= &devkit8000_vpll1,
+	.vio		= &devkit8000_vio,
 	.keypad		= &devkit8000_kp_data,
 };
 
-- 
1.7.1

[PATCHv2 01/11] OMAP2: Devkit8000: Cleanup for power supplies

[Thomas Weber]

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   32 ++++++++++++++++++++++++++------
 1 files changed, 26 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 922b746..08a2a01 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,6 +168,10 @@ static struct regulator_consumer_supply devkit8000_vsim_supply = {
 	.supply			= "vmmc_aux",
 };
 
+/* ads7846 on SPI */
+static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
+	REGULATOR_SUPPLY("vcc", "spi2.0")
+};
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -282,7 +286,7 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll2_supplies[] = {
+static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
 	.supply		= "vdvi",
 	.dev		= &devkit8000_lcd_device.dev,
@@ -337,8 +341,8 @@ static struct regulator_init_data devkit8000_vdac = {
 	.consumer_supplies	= &devkit8000_vdda_dac_supply,
 };
 
-/* VPLL2 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll2 = {
+/* VPLL1 for digital video outputs */
+static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
 		.name			= "VDVI",
 		.min_uV			= 1800000,
@@ -348,8 +352,23 @@ static struct regulator_init_data devkit8000_vpll2 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll2_supplies),
-	.consumer_supplies	= devkit8000_vpll2_supplies,
+	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
+	.consumer_supplies	= devkit8000_vpll1_supplies,
+};
+
+/* VAUX4 for ads7846 and nubs */
+static struct regulator_init_data devkit8000_vio = {
+	.constraints = {
+		.min_uV                 = 1800000,
+		.max_uV                 = 1800000,
+		.apply_uV               = true,
+		.valid_modes_mask       = REGULATOR_MODE_NORMAL
+			| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask         = REGULATOR_CHANGE_MODE
+			| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
+	.consumer_supplies      = devkit8000_vio_supplies,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
@@ -376,7 +395,8 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.vmmc1		= &devkit8000_vmmc1,
 	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
-	.vpll2		= &devkit8000_vpll2,
+	.vpll1		= &devkit8000_vpll1,
+	.vio		= &devkit8000_vio,
 	.keypad		= &devkit8000_kp_data,
 };
 
-- 
1.7.1

[PATCHv2 01/11] OMAP2: Devkit8000: Cleanup for power supplies

[Thomas Weber]

Corrected the wrong power supplies in devkit8000 code.

Add supply for ads7846 to support the new regulator framework for
touchscreen.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   32 ++++++++++++++++++++++++++------
 1 files changed, 26 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 922b746..08a2a01 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,6 +168,10 @@ static struct regulator_consumer_supply devkit8000_vsim_supply = {
 	.supply			= "vmmc_aux",
 };
 
+/* ads7846 on SPI */
+static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
+	REGULATOR_SUPPLY("vcc", "spi2.0")
+};
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -282,7 +286,7 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll2_supplies[] = {
+static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
 	.supply		= "vdvi",
 	.dev		= &devkit8000_lcd_device.dev,
@@ -337,8 +341,8 @@ static struct regulator_init_data devkit8000_vdac = {
 	.consumer_supplies	= &devkit8000_vdda_dac_supply,
 };
 
-/* VPLL2 for digital video outputs */
-static struct regulator_init_data devkit8000_vpll2 = {
+/* VPLL1 for digital video outputs */
+static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
 		.name			= "VDVI",
 		.min_uV			= 1800000,
@@ -348,8 +352,23 @@ static struct regulator_init_data devkit8000_vpll2 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll2_supplies),
-	.consumer_supplies	= devkit8000_vpll2_supplies,
+	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
+	.consumer_supplies	= devkit8000_vpll1_supplies,
+};
+
+/* VAUX4 for ads7846 and nubs */
+static struct regulator_init_data devkit8000_vio = {
+	.constraints = {
+		.min_uV                 = 1800000,
+		.max_uV                 = 1800000,
+		.apply_uV               = true,
+		.valid_modes_mask       = REGULATOR_MODE_NORMAL
+			| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask         = REGULATOR_CHANGE_MODE
+			| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
+	.consumer_supplies      = devkit8000_vio_supplies,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
@@ -376,7 +395,8 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.vmmc1		= &devkit8000_vmmc1,
 	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
-	.vpll2		= &devkit8000_vpll2,
+	.vpll1		= &devkit8000_vpll1,
+	.vio		= &devkit8000_vio,
 	.keypad		= &devkit8000_kp_data,
 };
 
-- 
1.7.1

[PATCHv2 02/11] OMAP2: Devkit8000: change panel to generic panel

[Thomas Weber]

Choose the generic panel for lcd code of Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 08a2a01..3bde0e6 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -175,7 +175,7 @@ static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
-	.driver_name            = "innolux_at_panel",
+	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
 	.platform_enable        = devkit8000_panel_enable_lcd,
-- 
1.7.1

[PATCHv2 02/11] OMAP2: Devkit8000: change panel to generic panel

[Thomas Weber]

Choose the generic panel for lcd code of Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 08a2a01..3bde0e6 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -175,7 +175,7 @@ static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
-	.driver_name            = "innolux_at_panel",
+	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
 	.platform_enable        = devkit8000_panel_enable_lcd,
-- 
1.7.1

[PATCHv2 02/11] OMAP2: Devkit8000: change panel to generic panel

[Thomas Weber]

Choose the generic panel for lcd code of Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 08a2a01..3bde0e6 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -175,7 +175,7 @@ static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
-	.driver_name            = "innolux_at_panel",
+	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
 	.platform_enable        = devkit8000_panel_enable_lcd,
-- 
1.7.1

[PATCHv2 03/11] OMAP2: Devkit8000: Enable DVI-D output

[Thomas Weber]

From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
 arch/arm/mach-omap2/board-devkit8000.c |   15 +++++++++++++++
 1 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3bde0e6..17a2517 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -140,13 +140,18 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
 }
+
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
@@ -186,6 +191,7 @@ static struct omap_dss_device devkit8000_dvi_device = {
 	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
+	.reset_gpio             = -EINVAL, /* will be replaced */
 	.platform_enable        = devkit8000_panel_enable_dvi,
 	.platform_disable       = devkit8000_panel_disable_dvi,
 };
@@ -272,6 +278,15 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
 	devkit8000_vsim_supply.dev = mmc[0].dev;
 
+	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+	/* gpio + 7 is "DVI_PD" (out, active low) */
+	devkit8000_dvi_device.reset_gpio = gpio + 7;
+	gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
+	/* Disable until needed */
+	gpio_direction_output(devkit8000_dvi_device.reset_gpio, 0);
+
 	return 0;
 }
 
-- 
1.7.1

[PATCHv2 03/11] OMAP2: Devkit8000: Enable DVI-D output

[Thomas Weber]

From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
 arch/arm/mach-omap2/board-devkit8000.c |   15 +++++++++++++++
 1 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3bde0e6..17a2517 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -140,13 +140,18 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
 }
+
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
@@ -186,6 +191,7 @@ static struct omap_dss_device devkit8000_dvi_device = {
 	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
+	.reset_gpio             = -EINVAL, /* will be replaced */
 	.platform_enable        = devkit8000_panel_enable_dvi,
 	.platform_disable       = devkit8000_panel_disable_dvi,
 };
@@ -272,6 +278,15 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
 	devkit8000_vsim_supply.dev = mmc[0].dev;
 
+	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+	/* gpio + 7 is "DVI_PD" (out, active low) */
+	devkit8000_dvi_device.reset_gpio = gpio + 7;
+	gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
+	/* Disable until needed */
+	gpio_direction_output(devkit8000_dvi_device.reset_gpio, 0);
+
 	return 0;
 }
 
-- 
1.7.1

[PATCHv2 03/11] OMAP2: Devkit8000: Enable DVI-D output

[Thomas Weber]

From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the DVI-D output setup of Devkit8000

Devkit8000 has different DVI reset pin with the BeagleBoard.
On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
 arch/arm/mach-omap2/board-devkit8000.c |   15 +++++++++++++++
 1 files changed, 15 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3bde0e6..17a2517 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -140,13 +140,18 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
 }
+
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
@@ -186,6 +191,7 @@ static struct omap_dss_device devkit8000_dvi_device = {
 	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
+	.reset_gpio             = -EINVAL, /* will be replaced */
 	.platform_enable        = devkit8000_panel_enable_dvi,
 	.platform_disable       = devkit8000_panel_disable_dvi,
 };
@@ -272,6 +278,15 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
 	devkit8000_vsim_supply.dev = mmc[0].dev;
 
+	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
+	/* gpio + 7 is "DVI_PD" (out, active low) */
+	devkit8000_dvi_device.reset_gpio = gpio + 7;
+	gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
+	/* Disable until needed */
+	gpio_direction_output(devkit8000_dvi_device.reset_gpio, 0);
+
 	return 0;
 }
 
-- 
1.7.1

[PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset

[Thomas Weber]

From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
 arch/arm/mach-omap2/board-devkit8000.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 17a2517..70552d8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -134,11 +134,15 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 	twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
 	twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
 
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
@@ -183,6 +187,7 @@ static struct omap_dss_device devkit8000_lcd_device = {
 	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
+	.reset_gpio             = -EINVAL, /* will be replaced */
 	.platform_enable        = devkit8000_panel_enable_lcd,
 	.platform_disable       = devkit8000_panel_disable_lcd,
 };
@@ -281,6 +286,12 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
+        /* gpio + 1 is "LCD_PWREN" (out, active high) */
+	devkit8000_lcd_device.reset_gpio = gpio + 1;
+	gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN");
+	/* Disable until needed */
+	gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);
+
 	/* gpio + 7 is "DVI_PD" (out, active low) */
 	devkit8000_dvi_device.reset_gpio = gpio + 7;
 	gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
-- 
1.7.1

[PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset

[Thomas Weber]

From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
 arch/arm/mach-omap2/board-devkit8000.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 17a2517..70552d8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -134,11 +134,15 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 	twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
 	twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
 
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
+	if (dssdev->reset_gpio != -EINVAL)
+		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
@@ -183,6 +187,7 @@ static struct omap_dss_device devkit8000_lcd_device = {
 	.driver_name            = "generic_panel",
 	.type                   = OMAP_DISPLAY_TYPE_DPI,
 	.phy.dpi.data_lines     = 24,
+	.reset_gpio             = -EINVAL, /* will be replaced */
 	.platform_enable        = devkit8000_panel_enable_lcd,
 	.platform_disable       = devkit8000_panel_disable_lcd,
 };
@@ -281,6 +286,12 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
+        /* gpio + 1 is "LCD_PWREN" (out, active high) */
+	devkit8000_lcd_device.reset_gpio = gpio + 1;
+	gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN");
+	/* Disable until needed */
+	gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);
+
 	/* gpio + 7 is "DVI_PD" (out, active low) */
 	devkit8000_dvi_device.reset_gpio = gpio + 7;
 	gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
-- 
1.7.1

[PATCHv2 05/11] OMAP2: Devkit8000: Remove unneeded VDVI supply

[Thomas Weber]

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    5 -----
 1 files changed, 0 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 70552d8..8cc8c3b 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -314,10 +314,6 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 
 static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
-	.supply		= "vdvi",
-	.dev		= &devkit8000_lcd_device.dev,
-	},
-	{
 	.supply		= "vdds_dsi",
 	.dev		= &devkit8000_dss_device.dev,
 	}
@@ -370,7 +366,6 @@ static struct regulator_init_data devkit8000_vdac = {
 /* VPLL1 for digital video outputs */
 static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
-		.name			= "VDVI",
 		.min_uV			= 1800000,
 		.max_uV			= 1800000,
 		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-- 
1.7.1

[PATCHv2 05/11] OMAP2: Devkit8000: Remove unneeded VDVI supply

[Thomas Weber]

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    5 -----
 1 files changed, 0 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 70552d8..8cc8c3b 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -314,10 +314,6 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 
 static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
-	.supply		= "vdvi",
-	.dev		= &devkit8000_lcd_device.dev,
-	},
-	{
 	.supply		= "vdds_dsi",
 	.dev		= &devkit8000_dss_device.dev,
 	}
@@ -370,7 +366,6 @@ static struct regulator_init_data devkit8000_vdac = {
 /* VPLL1 for digital video outputs */
 static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
-		.name			= "VDVI",
 		.min_uV			= 1800000,
 		.max_uV			= 1800000,
 		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-- 
1.7.1

[PATCHv2 05/11] OMAP2: Devkit8000: Remove unneeded VDVI supply

[Thomas Weber]

The VDVI power supply is no longer needed in
board code with the new DSS2 interface.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    5 -----
 1 files changed, 0 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 70552d8..8cc8c3b 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -314,10 +314,6 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 
 static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
 	{
-	.supply		= "vdvi",
-	.dev		= &devkit8000_lcd_device.dev,
-	},
-	{
 	.supply		= "vdds_dsi",
 	.dev		= &devkit8000_dss_device.dev,
 	}
@@ -370,7 +366,6 @@ static struct regulator_init_data devkit8000_vdac = {
 /* VPLL1 for digital video outputs */
 static struct regulator_init_data devkit8000_vpll1 = {
 	.constraints = {
-		.name			= "VDVI",
 		.min_uV			= 1800000,
 		.max_uV			= 1800000,
 		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-- 
1.7.1

[PATCHv2 06/11] OMAP2: Devkit8000: Remove non existing vsim supply

[Thomas Weber]

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   22 ----------------------
 1 files changed, 0 insertions(+), 22 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 8cc8c3b..59877b1 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,15 +168,10 @@ static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
 {
 }
 
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
 
-static struct regulator_consumer_supply devkit8000_vsim_supply = {
-	.supply			= "vmmc_aux",
-};
-
 /* ads7846 on SPI */
 static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 	REGULATOR_SUPPLY("vcc", "spi2.0")
@@ -281,7 +276,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 
 	/* link regulators to MMC adapters */
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
-	devkit8000_vsim_supply.dev = mmc[0].dev;
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -334,21 +328,6 @@ static struct regulator_init_data devkit8000_vmmc1 = {
 	.consumer_supplies	= &devkit8000_vmmc1_supply,
 };
 
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data devkit8000_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &devkit8000_vsim_supply,
-};
-
 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
 static struct regulator_init_data devkit8000_vdac = {
 	.constraints = {
@@ -414,7 +393,6 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.gpio		= &devkit8000_gpio_data,
 	.codec		= &devkit8000_codec_data,
 	.vmmc1		= &devkit8000_vmmc1,
-	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
 	.vpll1		= &devkit8000_vpll1,
 	.vio		= &devkit8000_vio,
-- 
1.7.1

[PATCHv2 06/11] OMAP2: Devkit8000: Remove non existing vsim supply

[Thomas Weber]

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   22 ----------------------
 1 files changed, 0 insertions(+), 22 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 8cc8c3b..59877b1 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,15 +168,10 @@ static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
 {
 }
 
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
 
-static struct regulator_consumer_supply devkit8000_vsim_supply = {
-	.supply			= "vmmc_aux",
-};
-
 /* ads7846 on SPI */
 static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 	REGULATOR_SUPPLY("vcc", "spi2.0")
@@ -281,7 +276,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 
 	/* link regulators to MMC adapters */
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
-	devkit8000_vsim_supply.dev = mmc[0].dev;
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -334,21 +328,6 @@ static struct regulator_init_data devkit8000_vmmc1 = {
 	.consumer_supplies	= &devkit8000_vmmc1_supply,
 };
 
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data devkit8000_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &devkit8000_vsim_supply,
-};
-
 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
 static struct regulator_init_data devkit8000_vdac = {
 	.constraints = {
@@ -414,7 +393,6 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.gpio		= &devkit8000_gpio_data,
 	.codec		= &devkit8000_codec_data,
 	.vmmc1		= &devkit8000_vmmc1,
-	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
 	.vpll1		= &devkit8000_vpll1,
 	.vio		= &devkit8000_vio,
-- 
1.7.1

[PATCHv2 06/11] OMAP2: Devkit8000: Remove non existing vsim supply

[Thomas Weber]

The Devkit8000 uses the cost reduced variant tps65930 of the twl4030.
The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2.

vaux2 is not used on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   22 ----------------------
 1 files changed, 0 insertions(+), 22 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 8cc8c3b..59877b1 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -168,15 +168,10 @@ static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
 {
 }
 
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
 
-static struct regulator_consumer_supply devkit8000_vsim_supply = {
-	.supply			= "vmmc_aux",
-};
-
 /* ads7846 on SPI */
 static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
 	REGULATOR_SUPPLY("vcc", "spi2.0")
@@ -281,7 +276,6 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 
 	/* link regulators to MMC adapters */
 	devkit8000_vmmc1_supply.dev = mmc[0].dev;
-	devkit8000_vsim_supply.dev = mmc[0].dev;
 
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -334,21 +328,6 @@ static struct regulator_init_data devkit8000_vmmc1 = {
 	.consumer_supplies	= &devkit8000_vmmc1_supply,
 };
 
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data devkit8000_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= 1,
-	.consumer_supplies	= &devkit8000_vsim_supply,
-};
-
 /* VDAC for DSS driving S-Video (8 mA unloaded, max 65 mA) */
 static struct regulator_init_data devkit8000_vdac = {
 	.constraints = {
@@ -414,7 +393,6 @@ static struct twl4030_platform_data devkit8000_twldata = {
 	.gpio		= &devkit8000_gpio_data,
 	.codec		= &devkit8000_codec_data,
 	.vmmc1		= &devkit8000_vmmc1,
-	.vsim		= &devkit8000_vsim,
 	.vdac		= &devkit8000_vdac,
 	.vpll1		= &devkit8000_vpll1,
 	.vio		= &devkit8000_vio,
-- 
1.7.1

[PATCHv2 07/11] OMAP2: Devkit8000: Remove en-/disable for tv panel

[Thomas Weber]

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   12 ------------
 1 files changed, 0 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 59877b1..095dc7a 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,16 +158,6 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
-{
-
-	return 0;
-}
-
-static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
-{
-}
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
@@ -201,8 +191,6 @@ static struct omap_dss_device devkit8000_tv_device = {
 	.driver_name            = "venc",
 	.type                   = OMAP_DISPLAY_TYPE_VENC,
 	.phy.venc.type          = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.platform_enable        = devkit8000_panel_enable_tv,
-	.platform_disable       = devkit8000_panel_disable_tv,
 };
 
 
-- 
1.7.1

[PATCHv2 07/11] OMAP2: Devkit8000: Remove en-/disable for tv panel

[Thomas Weber]

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   12 ------------
 1 files changed, 0 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 59877b1..095dc7a 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,16 +158,6 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
-{
-
-	return 0;
-}
-
-static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
-{
-}
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
@@ -201,8 +191,6 @@ static struct omap_dss_device devkit8000_tv_device = {
 	.driver_name            = "venc",
 	.type                   = OMAP_DISPLAY_TYPE_VENC,
 	.phy.venc.type          = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.platform_enable        = devkit8000_panel_enable_tv,
-	.platform_disable       = devkit8000_panel_disable_tv,
 };
 
 
-- 
1.7.1

[PATCHv2 07/11] OMAP2: Devkit8000: Remove en-/disable for tv panel

[Thomas Weber]

devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already
done in DSS2 code. So they are no longer needed in board code.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   12 ------------
 1 files changed, 0 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 59877b1..095dc7a 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,16 +158,6 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static int devkit8000_panel_enable_tv(struct omap_dss_device *dssdev)
-{
-
-	return 0;
-}
-
-static void devkit8000_panel_disable_tv(struct omap_dss_device *dssdev)
-{
-}
-
 static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
 	.supply			= "vmmc",
 };
@@ -201,8 +191,6 @@ static struct omap_dss_device devkit8000_tv_device = {
 	.driver_name            = "venc",
 	.type                   = OMAP_DISPLAY_TYPE_VENC,
 	.phy.venc.type          = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.platform_enable        = devkit8000_panel_enable_tv,
-	.platform_disable       = devkit8000_panel_disable_tv,
 };
 
 
-- 
1.7.1

[PATCHv2 08/11] OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro

[Thomas Weber]

Replacing supplies with the REGULATOR_SUPPLY macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   33 ++++++++++++-------------------
 1 files changed, 13 insertions(+), 20 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 095dc7a..3da88c8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,14 +158,13 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
-	.supply			= "vmmc",
-};
+static struct regulator_consumer_supply devkit8000_vmmc1_supply =
+	REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
+
 
 /* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi2.0")
-};
+static struct regulator_consumer_supply devkit8000_vio_supply =
+	REGULATOR_SUPPLY("vcc", "spi2.0");
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -214,10 +213,8 @@ static struct platform_device devkit8000_dss_device = {
 	},
 };
 
-static struct regulator_consumer_supply devkit8000_vdda_dac_supply = {
-	.supply = "vdda_dac",
-	.dev	= &devkit8000_dss_device.dev,
-};
+static struct regulator_consumer_supply devkit8000_vdda_dac_supply =
+	REGULATOR_SUPPLY("vdda_dac", "omapdss");
 
 static int board_keymap[] = {
 	KEY(0, 0, KEY_1),
@@ -294,12 +291,8 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
-	{
-	.supply		= "vdds_dsi",
-	.dev		= &devkit8000_dss_device.dev,
-	}
-};
+static struct regulator_consumer_supply devkit8000_vpll1_supply =
+	REGULATOR_SUPPLY("vdds_dsi", "omapdss");
 
 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
 static struct regulator_init_data devkit8000_vmmc1 = {
@@ -340,8 +333,8 @@ static struct regulator_init_data devkit8000_vpll1 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
-	.consumer_supplies	= devkit8000_vpll1_supplies,
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &devkit8000_vpll1_supply,
 };
 
 /* VAUX4 for ads7846 and nubs */
@@ -355,8 +348,8 @@ static struct regulator_init_data devkit8000_vio = {
 		.valid_ops_mask         = REGULATOR_CHANGE_MODE
 			| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
-	.consumer_supplies      = devkit8000_vio_supplies,
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &devkit8000_vio_supply,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
-- 
1.7.1

[PATCHv2 08/11] OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro

[Thomas Weber]

Replacing supplies with the REGULATOR_SUPPLY macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   33 ++++++++++++-------------------
 1 files changed, 13 insertions(+), 20 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 095dc7a..3da88c8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,14 +158,13 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
-	.supply			= "vmmc",
-};
+static struct regulator_consumer_supply devkit8000_vmmc1_supply =
+	REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
+
 
 /* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi2.0")
-};
+static struct regulator_consumer_supply devkit8000_vio_supply =
+	REGULATOR_SUPPLY("vcc", "spi2.0");
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -214,10 +213,8 @@ static struct platform_device devkit8000_dss_device = {
 	},
 };
 
-static struct regulator_consumer_supply devkit8000_vdda_dac_supply = {
-	.supply = "vdda_dac",
-	.dev	= &devkit8000_dss_device.dev,
-};
+static struct regulator_consumer_supply devkit8000_vdda_dac_supply =
+	REGULATOR_SUPPLY("vdda_dac", "omapdss");
 
 static int board_keymap[] = {
 	KEY(0, 0, KEY_1),
@@ -294,12 +291,8 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
-	{
-	.supply		= "vdds_dsi",
-	.dev		= &devkit8000_dss_device.dev,
-	}
-};
+static struct regulator_consumer_supply devkit8000_vpll1_supply =
+	REGULATOR_SUPPLY("vdds_dsi", "omapdss");
 
 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
 static struct regulator_init_data devkit8000_vmmc1 = {
@@ -340,8 +333,8 @@ static struct regulator_init_data devkit8000_vpll1 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
-	.consumer_supplies	= devkit8000_vpll1_supplies,
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &devkit8000_vpll1_supply,
 };
 
 /* VAUX4 for ads7846 and nubs */
@@ -355,8 +348,8 @@ static struct regulator_init_data devkit8000_vio = {
 		.valid_ops_mask         = REGULATOR_CHANGE_MODE
 			| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
-	.consumer_supplies      = devkit8000_vio_supplies,
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &devkit8000_vio_supply,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
-- 
1.7.1

[PATCHv2 08/11] OMAP2: Devkit8000: Using the REGULATOR_SUPPLY macro

[Thomas Weber]

Replacing supplies with the REGULATOR_SUPPLY macro.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |   33 ++++++++++++-------------------
 1 files changed, 13 insertions(+), 20 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 095dc7a..3da88c8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -158,14 +158,13 @@ static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-static struct regulator_consumer_supply devkit8000_vmmc1_supply = {
-	.supply			= "vmmc",
-};
+static struct regulator_consumer_supply devkit8000_vmmc1_supply =
+	REGULATOR_SUPPLY("vmmc", "mmci-omap-hs.0");
+
 
 /* ads7846 on SPI */
-static struct regulator_consumer_supply devkit8000_vio_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi2.0")
-};
+static struct regulator_consumer_supply devkit8000_vio_supply =
+	REGULATOR_SUPPLY("vcc", "spi2.0");
 
 static struct omap_dss_device devkit8000_lcd_device = {
 	.name                   = "lcd",
@@ -214,10 +213,8 @@ static struct platform_device devkit8000_dss_device = {
 	},
 };
 
-static struct regulator_consumer_supply devkit8000_vdda_dac_supply = {
-	.supply = "vdda_dac",
-	.dev	= &devkit8000_dss_device.dev,
-};
+static struct regulator_consumer_supply devkit8000_vdda_dac_supply =
+	REGULATOR_SUPPLY("vdda_dac", "omapdss");
 
 static int board_keymap[] = {
 	KEY(0, 0, KEY_1),
@@ -294,12 +291,8 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.setup		= devkit8000_twl_gpio_setup,
 };
 
-static struct regulator_consumer_supply devkit8000_vpll1_supplies[] = {
-	{
-	.supply		= "vdds_dsi",
-	.dev		= &devkit8000_dss_device.dev,
-	}
-};
+static struct regulator_consumer_supply devkit8000_vpll1_supply =
+	REGULATOR_SUPPLY("vdds_dsi", "omapdss");
 
 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
 static struct regulator_init_data devkit8000_vmmc1 = {
@@ -340,8 +333,8 @@ static struct regulator_init_data devkit8000_vpll1 = {
 		.valid_ops_mask		= REGULATOR_CHANGE_MODE
 					| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies	= ARRAY_SIZE(devkit8000_vpll1_supplies),
-	.consumer_supplies	= devkit8000_vpll1_supplies,
+	.num_consumer_supplies	= 1,
+	.consumer_supplies	= &devkit8000_vpll1_supply,
 };
 
 /* VAUX4 for ads7846 and nubs */
@@ -355,8 +348,8 @@ static struct regulator_init_data devkit8000_vio = {
 		.valid_ops_mask         = REGULATOR_CHANGE_MODE
 			| REGULATOR_CHANGE_STATUS,
 	},
-	.num_consumer_supplies  = ARRAY_SIZE(devkit8000_vio_supplies),
-	.consumer_supplies      = devkit8000_vio_supplies,
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &devkit8000_vio_supply,
 };
 
 static struct twl4030_usb_data devkit8000_usb_data = {
-- 
1.7.1

[PATCHv2 09/11] OMAP2: Devkit8000: Using gpio_is_valid macro

[Thomas Weber]

Using the macro gpio_is_valid for check of valid gpio pins.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3da88c8..dbd16de 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -134,27 +134,27 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 	twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
 	twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
 
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-- 
1.7.1

[PATCHv2 09/11] OMAP2: Devkit8000: Using gpio_is_valid macro

[Thomas Weber]

Using the macro gpio_is_valid for check of valid gpio pins.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 3da88c8..dbd16de 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -134,27 +134,27 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 	twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
 	twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
 
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
 static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 1);
 	return 0;
 }
 
 static void devkit8000_panel_disable_dvi(struct omap_dss_device *dssdev)
 {
-	if (dssdev->reset_gpio != -EINVAL)
+	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value(dssdev->reset_gpio, 0);
 }
 
-- 
1.7.1

[PATCHv2 10/11] OMAP2: Devkit8000: Remove unused omap_board_config

[Thomas Weber]

omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index dbd16de..a485d39 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -126,8 +126,6 @@ static struct omap2_hsmmc_info mmc[] = {
 	},
 	{}	/* Terminator */
 };
-static struct omap_board_config_kernel devkit8000_config[] __initdata = {
-};
 
 static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 {
@@ -464,8 +462,6 @@ static struct platform_device keys_gpio = {
 
 static void __init devkit8000_init_irq(void)
 {
-	omap_board_config = devkit8000_config;
-	omap_board_config_size = ARRAY_SIZE(devkit8000_config);
 	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
 			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
@@ -797,8 +793,6 @@ static void __init devkit8000_init(void)
 	devkit8000_i2c_init();
 	platform_add_devices(devkit8000_devices,
 			ARRAY_SIZE(devkit8000_devices));
-	omap_board_config = devkit8000_config;
-	omap_board_config_size = ARRAY_SIZE(devkit8000_config);
 
 	spi_register_board_info(devkit8000_spi_board_info,
 	ARRAY_SIZE(devkit8000_spi_board_info));
-- 
1.7.1

[PATCHv2 10/11] OMAP2: Devkit8000: Remove unused omap_board_config

[Thomas Weber]

omap_board_config is no longer used and thats why empty.
This patch removes the empty omap_board_config.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index dbd16de..a485d39 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -126,8 +126,6 @@ static struct omap2_hsmmc_info mmc[] = {
 	},
 	{}	/* Terminator */
 };
-static struct omap_board_config_kernel devkit8000_config[] __initdata = {
-};
 
 static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 {
@@ -464,8 +462,6 @@ static struct platform_device keys_gpio = {
 
 static void __init devkit8000_init_irq(void)
 {
-	omap_board_config = devkit8000_config;
-	omap_board_config_size = ARRAY_SIZE(devkit8000_config);
 	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
 			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
@@ -797,8 +793,6 @@ static void __init devkit8000_init(void)
 	devkit8000_i2c_init();
 	platform_add_devices(devkit8000_devices,
 			ARRAY_SIZE(devkit8000_devices));
-	omap_board_config = devkit8000_config;
-	omap_board_config_size = ARRAY_SIZE(devkit8000_config);
 
 	spi_register_board_info(devkit8000_spi_board_info,
 	ARRAY_SIZE(devkit8000_spi_board_info));
-- 
1.7.1

[PATCHv2 11/11] OMAP2: Devkit8000: Fix regulator for power supply

[Thomas Weber]

Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index a485d39..648b565 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -380,7 +380,7 @@ static struct twl4030_platform_data devkit8000_twldata = {
 
 static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
 	{
-		I2C_BOARD_INFO("twl4030", 0x48),
+		I2C_BOARD_INFO("tps65930", 0x48),
 		.flags = I2C_CLIENT_WAKE,
 		.irq = INT_34XX_SYS_NIRQ,
 		.platform_data = &devkit8000_twldata,
-- 
1.7.1

[PATCHv2 11/11] OMAP2: Devkit8000: Fix regulator for power supply

[Thomas Weber]

Devkit8000 uses the TPS65930 and not the TWL4030.
The TPS65930 uses only a subset of the power supplies
of the TWL4030.

Signed-off-by: Thomas Weber <weber@corscience.de>
---
 arch/arm/mach-omap2/board-devkit8000.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index a485d39..648b565 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -380,7 +380,7 @@ static struct twl4030_platform_data devkit8000_twldata = {
 
 static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
 	{
-		I2C_BOARD_INFO("twl4030", 0x48),
+		I2C_BOARD_INFO("tps65930", 0x48),
 		.flags = I2C_CLIENT_WAKE,
 		.irq = INT_34XX_SYS_NIRQ,
 		.platform_data = &devkit8000_twldata,
-- 
1.7.1

[APPLIED] [PATCHv2 01/11] OMAP2: Devkit8000: Cleanup for power supplies

[Tony Lindgren]

This patch has been applied to the linux-omap
by youw fwiendly patch wobot.

Branch in linux-omap: devel-boards

Initial commit ID (Likely to change): 463afcd5a832d0e3c8530e9cbbee329e019acb77

PatchWorks
http://patchwork.kernel.org/patch/103759/

Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=463afcd5a832d0e3c8530e9cbbee329e019acb77

[APPLIED] [PATCHv2 02/11] OMAP2: Devkit8000: change panel to generic panel

[Tony Lindgren]

This patch has been applied to the linux-omap
by youw fwiendly patch wobot.

Branch in linux-omap: devel-boards

Initial commit ID (Likely to change): 91fe4e154b2f422c9725e59d2d1f3dfcdbb504e7

PatchWorks
http://patchwork.kernel.org/patch/103762/

Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=91fe4e154b2f422c9725e59d2d1f3dfcdbb504e7

[APPLIED] [PATCHv2 03/11] OMAP2: Devkit8000: Enable DVI-D output

[Tony Lindgren]

This patch has been applied to the linux-omap
by youw fwiendly patch wobot.

Branch in linux-omap: devel-boards

Initial commit ID (Likely to change): 023a27927ca5f22b55db92a99da164452d66e537

PatchWorks
http://patchwork.kernel.org/patch/103763/

Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=023a27927ca5f22b55db92a99da164452d66e537

Re: [PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset

[Tony Lindgren]

* Thomas Weber <weber@corscience.de> [100602 14:33]:
> From: Kan-Ru Chen <kanru@0xlab.org>
> 
> This patch corrects the LCD reset pin configuration.
> 
> Original code from early devkit8000 patch sets the TWL4030 GPIO_1
> to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
> are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
> disabled when other display is turned on.

Applied this and the rest of the series too.

Tony

[PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset

[Tony Lindgren]

* Thomas Weber <weber@corscience.de> [100602 14:33]:
> From: Kan-Ru Chen <kanru@0xlab.org>
> 
> This patch corrects the LCD reset pin configuration.
> 
> Original code from early devkit8000 patch sets the TWL4030 GPIO_1
> to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
> are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
> disabled when other display is turned on.

Applied this and the rest of the series too.

Tony

Re: [PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset

[Thomas Weber]

Am 05.07.2010 14:57, schrieb Tony Lindgren:
> * Thomas Weber <weber@corscience.de> [100602 14:33]:
>   
>> From: Kan-Ru Chen <kanru@0xlab.org>
>>
>> This patch corrects the LCD reset pin configuration.
>>
>> Original code from early devkit8000 patch sets the TWL4030 GPIO_1
>> to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
>> are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
>> disabled when other display is turned on.
>>     
> Applied this and the rest of the series too.
>
>   
Thanks.
Thomas
> Tony
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>
>
>