All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
@ 2010-07-23 14:46 ` Marek Szyprowski
  0 siblings, 0 replies; 6+ messages in thread
From: Marek Szyprowski @ 2010-07-23 14:46 UTC (permalink / raw)
  To: linux-samsung-soc, linux-arm-kernel
  Cc: m.szyprowski, kyungmin.park, kgene.kim, ben-linux

This patch add support for SDHCI blocks on Samsung Aquila board. The
following host controllers are defined:
1. Internal MoviNAND device (permanently wired to the controller)
2. Internal WiFI SDIO device (card is activated by power regualor)
3. External MMC/SD socket (card detection is provided by external
gpio interrupt)

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv210/Kconfig       |    4 +++
 arch/arm/mach-s5pv210/mach-aquila.c |   39 +++++++++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 12a2c6b..c64dff1 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -60,8 +60,12 @@ config MACH_AQUILA
 	select CPU_S5PV210
 	select ARCH_SPARSEMEM_ENABLE
 	select S5PV210_SETUP_FB_24BPP
+	select S5PV210_SETUP_SDHCI
 	select S3C_DEV_FB
 	select S5PC110_DEV_ONENAND
+	select S3C_DEV_HSMMC
+	select S3C_DEV_HSMMC1
+	select S3C_DEV_HSMMC2
 	help
 	  Machine support for the Samsung Aquila target based on S5PC110 SoC
 
diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c
index 0992618..a1f8d07 100644
--- a/arch/arm/mach-s5pv210/mach-aquila.c
+++ b/arch/arm/mach-s5pv210/mach-aquila.c
@@ -35,6 +35,7 @@
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/fb.h>
+#include <plat/sdhci.h>
 
 /* Following are default values for UCON, ULCON and UFCON UART registers */
 #define S5PV210_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
@@ -440,11 +441,47 @@ static void __init aquila_pmic_init(void)
 	s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP);
 }
 
+/* MoviNAND */
+static struct s3c_sdhci_platdata aquila_hsmmc0_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_PERMANENT,
+};
+
+/* Wireless LAN */
+static struct s3c_sdhci_platdata aquila_hsmmc1_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_EXTERNAL,
+	/* ext_cd_{init,cleanup} callbacks will be added later */
+};
+
+/* External Flash */
+#define AQUILA_EXT_FLASH_EN	S5PV210_MP05(4)
+#define AQUILA_EXT_FLASH_CD	S5PV210_GPH3(4)
+static struct s3c_sdhci_platdata aquila_hsmmc2_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_GPIO,
+	.ext_cd_gpio		= AQUILA_EXT_FLASH_CD,
+	.ext_cd_gpio_invert	= 1,
+};
+
+static void aquila_setup_sdhci(void)
+{
+	gpio_request(AQUILA_EXT_FLASH_EN, "FLASH_EN");
+	gpio_direction_output(AQUILA_EXT_FLASH_EN, 1);
+
+	s3c_sdhci0_set_platdata(&aquila_hsmmc0_data);
+	s3c_sdhci1_set_platdata(&aquila_hsmmc1_data);
+	s3c_sdhci2_set_platdata(&aquila_hsmmc2_data);
+};
+
 static struct platform_device *aquila_devices[] __initdata = {
 	&aquila_i2c_gpio_pmic,
 	&aquila_device_gpiokeys,
 	&s3c_device_fb,
 	&s5pc110_device_onenand,
+	&s3c_device_hsmmc0,
+	&s3c_device_hsmmc1,
+	&s3c_device_hsmmc2,
 };
 
 static void __init aquila_map_io(void)
@@ -460,6 +497,8 @@ static void __init aquila_machine_init(void)
 	aquila_pmic_init();
 	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4, i2c_gpio_pmic_devs,
 			ARRAY_SIZE(i2c_gpio_pmic_devs));
+	/* SDHCI */
+	aquila_setup_sdhci();
 
 	/* FB */
 	s3c_fb_set_platdata(&aquila_lcd_pdata);
-- 
1.7.1.569.g6f426

^ permalink raw reply related	[flat|nested] 6+ messages in thread
* [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
@ 2010-07-23 14:46 ` Marek Szyprowski
  0 siblings, 0 replies; 6+ messages in thread
From: Marek Szyprowski @ 2010-07-23 14:46 UTC (permalink / raw)
  To: linux-arm-kernel

This patch add support for SDHCI blocks on Samsung Aquila board. The
following host controllers are defined:
1. Internal MoviNAND device (permanently wired to the controller)
2. Internal WiFI SDIO device (card is activated by power regualor)
3. External MMC/SD socket (card detection is provided by external
gpio interrupt)

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
 arch/arm/mach-s5pv210/Kconfig       |    4 +++
 arch/arm/mach-s5pv210/mach-aquila.c |   39 +++++++++++++++++++++++++++++++++++
 2 files changed, 43 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 12a2c6b..c64dff1 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -60,8 +60,12 @@ config MACH_AQUILA
 	select CPU_S5PV210
 	select ARCH_SPARSEMEM_ENABLE
 	select S5PV210_SETUP_FB_24BPP
+	select S5PV210_SETUP_SDHCI
 	select S3C_DEV_FB
 	select S5PC110_DEV_ONENAND
+	select S3C_DEV_HSMMC
+	select S3C_DEV_HSMMC1
+	select S3C_DEV_HSMMC2
 	help
 	  Machine support for the Samsung Aquila target based on S5PC110 SoC
 
diff --git a/arch/arm/mach-s5pv210/mach-aquila.c b/arch/arm/mach-s5pv210/mach-aquila.c
index 0992618..a1f8d07 100644
--- a/arch/arm/mach-s5pv210/mach-aquila.c
+++ b/arch/arm/mach-s5pv210/mach-aquila.c
@@ -35,6 +35,7 @@
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/fb.h>
+#include <plat/sdhci.h>
 
 /* Following are default values for UCON, ULCON and UFCON UART registers */
 #define S5PV210_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
@@ -440,11 +441,47 @@ static void __init aquila_pmic_init(void)
 	s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP);
 }
 
+/* MoviNAND */
+static struct s3c_sdhci_platdata aquila_hsmmc0_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_PERMANENT,
+};
+
+/* Wireless LAN */
+static struct s3c_sdhci_platdata aquila_hsmmc1_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_EXTERNAL,
+	/* ext_cd_{init,cleanup} callbacks will be added later */
+};
+
+/* External Flash */
+#define AQUILA_EXT_FLASH_EN	S5PV210_MP05(4)
+#define AQUILA_EXT_FLASH_CD	S5PV210_GPH3(4)
+static struct s3c_sdhci_platdata aquila_hsmmc2_data __initdata = {
+	.max_width		= 4,
+	.cd_type		= S3C_SDHCI_CD_GPIO,
+	.ext_cd_gpio		= AQUILA_EXT_FLASH_CD,
+	.ext_cd_gpio_invert	= 1,
+};
+
+static void aquila_setup_sdhci(void)
+{
+	gpio_request(AQUILA_EXT_FLASH_EN, "FLASH_EN");
+	gpio_direction_output(AQUILA_EXT_FLASH_EN, 1);
+
+	s3c_sdhci0_set_platdata(&aquila_hsmmc0_data);
+	s3c_sdhci1_set_platdata(&aquila_hsmmc1_data);
+	s3c_sdhci2_set_platdata(&aquila_hsmmc2_data);
+};
+
 static struct platform_device *aquila_devices[] __initdata = {
 	&aquila_i2c_gpio_pmic,
 	&aquila_device_gpiokeys,
 	&s3c_device_fb,
 	&s5pc110_device_onenand,
+	&s3c_device_hsmmc0,
+	&s3c_device_hsmmc1,
+	&s3c_device_hsmmc2,
 };
 
 static void __init aquila_map_io(void)
@@ -460,6 +497,8 @@ static void __init aquila_machine_init(void)
 	aquila_pmic_init();
 	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4, i2c_gpio_pmic_devs,
 			ARRAY_SIZE(i2c_gpio_pmic_devs));
+	/* SDHCI */
+	aquila_setup_sdhci();
 
 	/* FB */
 	s3c_fb_set_platdata(&aquila_lcd_pdata);
-- 
1.7.1.569.g6f426

^ permalink raw reply related	[flat|nested] 6+ messages in thread
* Re: [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
  2010-07-23 14:46 ` Marek Szyprowski
@ 2010-07-28 15:03   ` nitin vishnoi
  -1 siblings, 0 replies; 6+ messages in thread
From: nitin vishnoi @ 2010-07-28 15:03 UTC (permalink / raw)
  To: Marek Szyprowski
  Cc: kgene.kim, kyungmin.park, linux-samsung-soc, ben-linux, linux-arm-kernel


[-- Attachment #1.1: Type: text/plain, Size: 396 bytes --]

Hi

I need the support for wifi driver(lpm series chip),it needs the sdio
interface,but i m using the 2.6.21.7 kernel version.in which sdio driver is
not supporting for the Wifi(unifi_sdio) driver.
and in wifi driver installation guide also it is given wifi driver will
support higher than 2.6.24 version and onwards.
So can i get some patch for 2.6.21.7 version for sdio driver.

Regards

Nitin

[-- Attachment #1.2: Type: text/html, Size: 462 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 6+ messages in thread
* [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
@ 2010-07-28 15:03   ` nitin vishnoi
  0 siblings, 0 replies; 6+ messages in thread
From: nitin vishnoi @ 2010-07-28 15:03 UTC (permalink / raw)
  To: linux-arm-kernel

Hi

I need the support for wifi driver(lpm series chip),it needs the sdio
interface,but i m using the 2.6.21.7 kernel version.in which sdio driver is
not supporting for the Wifi(unifi_sdio) driver.
and in wifi driver installation guide also it is given wifi driver will
support higher than 2.6.24 version and onwards.
So can i get some patch for 2.6.21.7 version for sdio driver.

Regards

Nitin
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100728/f54bdbd6/attachment-0001.html>

^ permalink raw reply	[flat|nested] 6+ messages in thread
* RE: [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
  2010-07-23 14:46 ` Marek Szyprowski
@ 2010-08-04 10:56   ` Kukjin Kim
  -1 siblings, 0 replies; 6+ messages in thread
From: Kukjin Kim @ 2010-08-04 10:56 UTC (permalink / raw)
  To: 'Marek Szyprowski', linux-samsung-soc, linux-arm-kernel
  Cc: kyungmin.park, ben-linux

Marek Szyprowski wrote:
> 
> This patch add support for SDHCI blocks on Samsung Aquila board. The
> following host controllers are defined:
> 1. Internal MoviNAND device (permanently wired to the controller)
> 2. Internal WiFI SDIO device (card is activated by power regualor)
> 3. External MMC/SD socket (card detection is provided by external
> gpio interrupt)
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv210/Kconfig       |    4 +++
>  arch/arm/mach-s5pv210/mach-aquila.c |   39
> +++++++++++++++++++++++++++++++++++
>  2 files changed, 43 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
> index 12a2c6b..c64dff1 100644
> --- a/arch/arm/mach-s5pv210/Kconfig
> +++ b/arch/arm/mach-s5pv210/Kconfig
> @@ -60,8 +60,12 @@ config MACH_AQUILA
>  	select CPU_S5PV210
>  	select ARCH_SPARSEMEM_ENABLE
>  	select S5PV210_SETUP_FB_24BPP
> +	select S5PV210_SETUP_SDHCI
>  	select S3C_DEV_FB
>  	select S5PC110_DEV_ONENAND
> +	select S3C_DEV_HSMMC
> +	select S3C_DEV_HSMMC1
> +	select S3C_DEV_HSMMC2
>  	help
>  	  Machine support for the Samsung Aquila target based on S5PC110
> SoC
> 
> diff --git a/arch/arm/mach-s5pv210/mach-aquila.c
b/arch/arm/mach-s5pv210/mach-
> aquila.c
> index 0992618..a1f8d07 100644
> --- a/arch/arm/mach-s5pv210/mach-aquila.c
> +++ b/arch/arm/mach-s5pv210/mach-aquila.c
> @@ -35,6 +35,7 @@
>  #include <plat/devs.h>
>  #include <plat/cpu.h>
>  #include <plat/fb.h>
> +#include <plat/sdhci.h>
> 
>  /* Following are default values for UCON, ULCON and UFCON UART registers
*/
>  #define S5PV210_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
> @@ -440,11 +441,47 @@ static void __init aquila_pmic_init(void)
>  	s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP);
>  }
> 
> +/* MoviNAND */
> +static struct s3c_sdhci_platdata aquila_hsmmc0_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_PERMANENT,
> +};
> +
> +/* Wireless LAN */
> +static struct s3c_sdhci_platdata aquila_hsmmc1_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_EXTERNAL,
> +	/* ext_cd_{init,cleanup} callbacks will be added later */
> +};
> +
> +/* External Flash */
> +#define AQUILA_EXT_FLASH_EN	S5PV210_MP05(4)
> +#define AQUILA_EXT_FLASH_CD	S5PV210_GPH3(4)
> +static struct s3c_sdhci_platdata aquila_hsmmc2_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_GPIO,
> +	.ext_cd_gpio		= AQUILA_EXT_FLASH_CD,
> +	.ext_cd_gpio_invert	= 1,
> +};
> +
> +static void aquila_setup_sdhci(void)
> +{
> +	gpio_request(AQUILA_EXT_FLASH_EN, "FLASH_EN");
> +	gpio_direction_output(AQUILA_EXT_FLASH_EN, 1);
> +
> +	s3c_sdhci0_set_platdata(&aquila_hsmmc0_data);
> +	s3c_sdhci1_set_platdata(&aquila_hsmmc1_data);
> +	s3c_sdhci2_set_platdata(&aquila_hsmmc2_data);
> +};
> +
>  static struct platform_device *aquila_devices[] __initdata = {
>  	&aquila_i2c_gpio_pmic,
>  	&aquila_device_gpiokeys,
>  	&s3c_device_fb,
>  	&s5pc110_device_onenand,
> +	&s3c_device_hsmmc0,
> +	&s3c_device_hsmmc1,
> +	&s3c_device_hsmmc2,
>  };
> 
>  static void __init aquila_map_io(void)
> @@ -460,6 +497,8 @@ static void __init aquila_machine_init(void)
>  	aquila_pmic_init();
>  	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4,
> i2c_gpio_pmic_devs,
>  			ARRAY_SIZE(i2c_gpio_pmic_devs));
> +	/* SDHCI */
> +	aquila_setup_sdhci();
> 
>  	/* FB */
>  	s3c_fb_set_platdata(&aquila_lcd_pdata);
> --
Looks ok..will apply.

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

^ permalink raw reply	[flat|nested] 6+ messages in thread
* [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board
@ 2010-08-04 10:56   ` Kukjin Kim
  0 siblings, 0 replies; 6+ messages in thread
From: Kukjin Kim @ 2010-08-04 10:56 UTC (permalink / raw)
  To: linux-arm-kernel

Marek Szyprowski wrote:
> 
> This patch add support for SDHCI blocks on Samsung Aquila board. The
> following host controllers are defined:
> 1. Internal MoviNAND device (permanently wired to the controller)
> 2. Internal WiFI SDIO device (card is activated by power regualor)
> 3. External MMC/SD socket (card detection is provided by external
> gpio interrupt)
> 
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
>  arch/arm/mach-s5pv210/Kconfig       |    4 +++
>  arch/arm/mach-s5pv210/mach-aquila.c |   39
> +++++++++++++++++++++++++++++++++++
>  2 files changed, 43 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
> index 12a2c6b..c64dff1 100644
> --- a/arch/arm/mach-s5pv210/Kconfig
> +++ b/arch/arm/mach-s5pv210/Kconfig
> @@ -60,8 +60,12 @@ config MACH_AQUILA
>  	select CPU_S5PV210
>  	select ARCH_SPARSEMEM_ENABLE
>  	select S5PV210_SETUP_FB_24BPP
> +	select S5PV210_SETUP_SDHCI
>  	select S3C_DEV_FB
>  	select S5PC110_DEV_ONENAND
> +	select S3C_DEV_HSMMC
> +	select S3C_DEV_HSMMC1
> +	select S3C_DEV_HSMMC2
>  	help
>  	  Machine support for the Samsung Aquila target based on S5PC110
> SoC
> 
> diff --git a/arch/arm/mach-s5pv210/mach-aquila.c
b/arch/arm/mach-s5pv210/mach-
> aquila.c
> index 0992618..a1f8d07 100644
> --- a/arch/arm/mach-s5pv210/mach-aquila.c
> +++ b/arch/arm/mach-s5pv210/mach-aquila.c
> @@ -35,6 +35,7 @@
>  #include <plat/devs.h>
>  #include <plat/cpu.h>
>  #include <plat/fb.h>
> +#include <plat/sdhci.h>
> 
>  /* Following are default values for UCON, ULCON and UFCON UART registers
*/
>  #define S5PV210_UCON_DEFAULT	(S3C2410_UCON_TXILEVEL |	\
> @@ -440,11 +441,47 @@ static void __init aquila_pmic_init(void)
>  	s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP);
>  }
> 
> +/* MoviNAND */
> +static struct s3c_sdhci_platdata aquila_hsmmc0_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_PERMANENT,
> +};
> +
> +/* Wireless LAN */
> +static struct s3c_sdhci_platdata aquila_hsmmc1_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_EXTERNAL,
> +	/* ext_cd_{init,cleanup} callbacks will be added later */
> +};
> +
> +/* External Flash */
> +#define AQUILA_EXT_FLASH_EN	S5PV210_MP05(4)
> +#define AQUILA_EXT_FLASH_CD	S5PV210_GPH3(4)
> +static struct s3c_sdhci_platdata aquila_hsmmc2_data __initdata = {
> +	.max_width		= 4,
> +	.cd_type		= S3C_SDHCI_CD_GPIO,
> +	.ext_cd_gpio		= AQUILA_EXT_FLASH_CD,
> +	.ext_cd_gpio_invert	= 1,
> +};
> +
> +static void aquila_setup_sdhci(void)
> +{
> +	gpio_request(AQUILA_EXT_FLASH_EN, "FLASH_EN");
> +	gpio_direction_output(AQUILA_EXT_FLASH_EN, 1);
> +
> +	s3c_sdhci0_set_platdata(&aquila_hsmmc0_data);
> +	s3c_sdhci1_set_platdata(&aquila_hsmmc1_data);
> +	s3c_sdhci2_set_platdata(&aquila_hsmmc2_data);
> +};
> +
>  static struct platform_device *aquila_devices[] __initdata = {
>  	&aquila_i2c_gpio_pmic,
>  	&aquila_device_gpiokeys,
>  	&s3c_device_fb,
>  	&s5pc110_device_onenand,
> +	&s3c_device_hsmmc0,
> +	&s3c_device_hsmmc1,
> +	&s3c_device_hsmmc2,
>  };
> 
>  static void __init aquila_map_io(void)
> @@ -460,6 +497,8 @@ static void __init aquila_machine_init(void)
>  	aquila_pmic_init();
>  	i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4,
> i2c_gpio_pmic_devs,
>  			ARRAY_SIZE(i2c_gpio_pmic_devs));
> +	/* SDHCI */
> +	aquila_setup_sdhci();
> 
>  	/* FB */
>  	s3c_fb_set_platdata(&aquila_lcd_pdata);
> --
Looks ok..will apply.

Thanks.

Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.

^ permalink raw reply	[flat|nested] 6+ messages in thread
end of thread, other threads:[~2010-08-04 10:56 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-07-23 14:46 [PATCH] ARM: S5PV210: Add SDHCI devices for Aquila board Marek Szyprowski
2010-07-23 14:46 ` Marek Szyprowski
2010-07-28 15:03 ` nitin vishnoi
2010-07-28 15:03   ` nitin vishnoi
2010-08-04 10:56 ` Kukjin Kim
2010-08-04 10:56   ` Kukjin Kim

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.