From: Marek Szyprowski <m.szyprowski@samsung.com> To: linux-samsung-soc@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: m.szyprowski@samsung.com, kyungmin.park@samsung.com, kgene.kim@samsung.com, ben-linux@fluff.org Subject: [PATCH] ARM: S5PV210: Add SDHCI devices for GONI board Date: Fri, 23 Jul 2010 16:47:00 +0200 [thread overview] Message-ID: <1279896420-29642-1-git-send-email-m.szyprowski@samsung.com> (raw) This patch add support for SDHCI blocks on Samsung Goni board. The following host controllers are defined: 1. Internal MoviNAND device (permanently wired to the controller) 2. Internal WiFI SDIO device (card is activated by power regualor) 3. External MMC/SD socket (card detection is provided by external gpio interrupt) Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> --- arch/arm/mach-s5pv210/Kconfig | 4 +++ arch/arm/mach-s5pv210/mach-goni.c | 39 +++++++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig index c64dff1..13e0690 100644 --- a/arch/arm/mach-s5pv210/Kconfig +++ b/arch/arm/mach-s5pv210/Kconfig @@ -74,8 +74,12 @@ config MACH_GONI select CPU_S5PV210 select ARCH_SPARSEMEM_ENABLE select S5PV210_SETUP_FB_24BPP + select S5PV210_SETUP_SDHCI select S3C_DEV_FB select S5PC110_DEV_ONENAND + select S3C_DEV_HSMMC + select S3C_DEV_HSMMC1 + select S3C_DEV_HSMMC2 help Machine support for Samsung GONI board S5PC110(MCP) is one of package option of S5PV210 diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index 7b18505..e374b34 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -35,6 +35,7 @@ #include <plat/devs.h> #include <plat/cpu.h> #include <plat/fb.h> +#include <plat/sdhci.h> /* Following are default values for UCON, ULCON and UFCON UART registers */ #define S5PV210_UCON_DEFAULT (S3C2410_UCON_TXILEVEL | \ @@ -420,12 +421,47 @@ static void __init goni_pmic_init(void) s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP); } +/* MoviNAND */ +static struct s3c_sdhci_platdata goni_hsmmc0_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_PERMANENT, +}; + +/* Wireless LAN */ +static struct s3c_sdhci_platdata goni_hsmmc1_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_EXTERNAL, + /* ext_cd_{init,cleanup} callbacks will be added later */ +}; + +/* External Flash */ +#define GONI_EXT_FLASH_EN S5PV210_MP05(4) +#define GONI_EXT_FLASH_CD S5PV210_GPH3(4) +static struct s3c_sdhci_platdata goni_hsmmc2_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_GPIO, + .ext_cd_gpio = GONI_EXT_FLASH_CD, + .ext_cd_gpio_invert = 1, +}; + +static void goni_setup_sdhci(void) +{ + gpio_request(GONI_EXT_FLASH_EN, "FLASH_EN"); + gpio_direction_output(GONI_EXT_FLASH_EN, 1); + + s3c_sdhci0_set_platdata(&goni_hsmmc0_data); + s3c_sdhci1_set_platdata(&goni_hsmmc1_data); + s3c_sdhci2_set_platdata(&goni_hsmmc2_data); +}; static struct platform_device *goni_devices[] __initdata = { &s3c_device_fb, &s5pc110_device_onenand, &goni_i2c_gpio_pmic, &goni_device_gpiokeys, + &s3c_device_hsmmc0, + &s3c_device_hsmmc1, + &s3c_device_hsmmc2, }; static void __init goni_map_io(void) @@ -441,6 +477,9 @@ static void __init goni_machine_init(void) goni_pmic_init(); i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4, i2c_gpio_pmic_devs, ARRAY_SIZE(i2c_gpio_pmic_devs)); + /* SDHCI */ + goni_setup_sdhci(); + /* FB */ s3c_fb_set_platdata(&goni_lcd_pdata); -- 1.7.1.569.g6f426
WARNING: multiple messages have this Message-ID (diff)
From: m.szyprowski@samsung.com (Marek Szyprowski) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH] ARM: S5PV210: Add SDHCI devices for GONI board Date: Fri, 23 Jul 2010 16:47:00 +0200 [thread overview] Message-ID: <1279896420-29642-1-git-send-email-m.szyprowski@samsung.com> (raw) This patch add support for SDHCI blocks on Samsung Goni board. The following host controllers are defined: 1. Internal MoviNAND device (permanently wired to the controller) 2. Internal WiFI SDIO device (card is activated by power regualor) 3. External MMC/SD socket (card detection is provided by external gpio interrupt) Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> --- arch/arm/mach-s5pv210/Kconfig | 4 +++ arch/arm/mach-s5pv210/mach-goni.c | 39 +++++++++++++++++++++++++++++++++++++ 2 files changed, 43 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig index c64dff1..13e0690 100644 --- a/arch/arm/mach-s5pv210/Kconfig +++ b/arch/arm/mach-s5pv210/Kconfig @@ -74,8 +74,12 @@ config MACH_GONI select CPU_S5PV210 select ARCH_SPARSEMEM_ENABLE select S5PV210_SETUP_FB_24BPP + select S5PV210_SETUP_SDHCI select S3C_DEV_FB select S5PC110_DEV_ONENAND + select S3C_DEV_HSMMC + select S3C_DEV_HSMMC1 + select S3C_DEV_HSMMC2 help Machine support for Samsung GONI board S5PC110(MCP) is one of package option of S5PV210 diff --git a/arch/arm/mach-s5pv210/mach-goni.c b/arch/arm/mach-s5pv210/mach-goni.c index 7b18505..e374b34 100644 --- a/arch/arm/mach-s5pv210/mach-goni.c +++ b/arch/arm/mach-s5pv210/mach-goni.c @@ -35,6 +35,7 @@ #include <plat/devs.h> #include <plat/cpu.h> #include <plat/fb.h> +#include <plat/sdhci.h> /* Following are default values for UCON, ULCON and UFCON UART registers */ #define S5PV210_UCON_DEFAULT (S3C2410_UCON_TXILEVEL | \ @@ -420,12 +421,47 @@ static void __init goni_pmic_init(void) s3c_gpio_setpull(S5PV210_GPH2(6), S3C_GPIO_PULL_UP); } +/* MoviNAND */ +static struct s3c_sdhci_platdata goni_hsmmc0_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_PERMANENT, +}; + +/* Wireless LAN */ +static struct s3c_sdhci_platdata goni_hsmmc1_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_EXTERNAL, + /* ext_cd_{init,cleanup} callbacks will be added later */ +}; + +/* External Flash */ +#define GONI_EXT_FLASH_EN S5PV210_MP05(4) +#define GONI_EXT_FLASH_CD S5PV210_GPH3(4) +static struct s3c_sdhci_platdata goni_hsmmc2_data __initdata = { + .max_width = 4, + .cd_type = S3C_SDHCI_CD_GPIO, + .ext_cd_gpio = GONI_EXT_FLASH_CD, + .ext_cd_gpio_invert = 1, +}; + +static void goni_setup_sdhci(void) +{ + gpio_request(GONI_EXT_FLASH_EN, "FLASH_EN"); + gpio_direction_output(GONI_EXT_FLASH_EN, 1); + + s3c_sdhci0_set_platdata(&goni_hsmmc0_data); + s3c_sdhci1_set_platdata(&goni_hsmmc1_data); + s3c_sdhci2_set_platdata(&goni_hsmmc2_data); +}; static struct platform_device *goni_devices[] __initdata = { &s3c_device_fb, &s5pc110_device_onenand, &goni_i2c_gpio_pmic, &goni_device_gpiokeys, + &s3c_device_hsmmc0, + &s3c_device_hsmmc1, + &s3c_device_hsmmc2, }; static void __init goni_map_io(void) @@ -441,6 +477,9 @@ static void __init goni_machine_init(void) goni_pmic_init(); i2c_register_board_info(AP_I2C_GPIO_PMIC_BUS_4, i2c_gpio_pmic_devs, ARRAY_SIZE(i2c_gpio_pmic_devs)); + /* SDHCI */ + goni_setup_sdhci(); + /* FB */ s3c_fb_set_platdata(&goni_lcd_pdata); -- 1.7.1.569.g6f426
next reply other threads:[~2010-07-23 14:47 UTC|newest] Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top 2010-07-23 14:47 Marek Szyprowski [this message] 2010-07-23 14:47 ` [PATCH] ARM: S5PV210: Add SDHCI devices for GONI board Marek Szyprowski 2010-08-04 11:02 ` Kukjin Kim 2010-08-04 11:02 ` Kukjin Kim
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1279896420-29642-1-git-send-email-m.szyprowski@samsung.com \ --to=m.szyprowski@samsung.com \ --cc=ben-linux@fluff.org \ --cc=kgene.kim@samsung.com \ --cc=kyungmin.park@samsung.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-samsung-soc@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.