* [PATCH 1/1] ti-tisdk-setup: add recipe to install setup scripts
@ 2010-08-04 15:17 Chase Maupin
0 siblings, 0 replies; only message in thread
From: Chase Maupin @ 2010-08-04 15:17 UTC (permalink / raw)
To: openembedded-devel
* Added recipe that installs setup scripts for the development
host. i.e. configurating nfs and tftp.
* Adds script to setup u-boot environment variables.
Signed-off-by: Chase Maupin <chase.maupin@ti.com>
---
recipes/ti/ti-tisdk-setup.bb | 30 +++
.../am37x-evm/setup/setup-uboot-env.sh | 217 ++++++++++++++++++
.../dm365-evm/setup/setup-uboot-env.sh | 237 ++++++++++++++++++++
.../dm37x-evm/setup/setup-uboot-env.sh | 217 ++++++++++++++++++
.../omap3evm/setup/setup-uboot-env.sh | 217 ++++++++++++++++++
.../omapl138/setup/setup-uboot-env.sh | 213 ++++++++++++++++++
recipes/ti/ti-tisdk-setup/setup/common.sh | 9 +
.../ti/ti-tisdk-setup/setup/setup-host-check.sh | 13 +
recipes/ti/ti-tisdk-setup/setup/setup-minicom.sh | 51 +++++
.../ti-tisdk-setup/setup/setup-package-install.sh | 21 ++
.../ti/ti-tisdk-setup/setup/setup-targetfs-nfs.sh | 79 +++++++
recipes/ti/ti-tisdk-setup/setup/setup-tftp.sh | 81 +++++++
recipes/ti/ti-tisdk-setup/setup/setup.sh | 35 +++
13 files changed, 1420 insertions(+), 0 deletions(-)
create mode 100644 recipes/ti/ti-tisdk-setup.bb
create mode 100644 recipes/ti/ti-tisdk-setup/am37x-evm/setup/setup-uboot-env.sh
create mode 100644 recipes/ti/ti-tisdk-setup/dm365-evm/setup/setup-uboot-env.sh
create mode 100644 recipes/ti/ti-tisdk-setup/dm37x-evm/setup/setup-uboot-env.sh
create mode 100644 recipes/ti/ti-tisdk-setup/omap3evm/setup/setup-uboot-env.sh
create mode 100644 recipes/ti/ti-tisdk-setup/omapl138/setup/setup-uboot-env.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/common.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup-host-check.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup-minicom.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup-package-install.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup-targetfs-nfs.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup-tftp.sh
create mode 100644 recipes/ti/ti-tisdk-setup/setup/setup.sh
diff --git a/recipes/ti/ti-tisdk-setup.bb b/recipes/ti/ti-tisdk-setup.bb
new file mode 100644
index 0000000..6713ef1
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup.bb
@@ -0,0 +1,30 @@
+DESCRIPTION = "Package containing scripts to setup the development host and target board"
+LICENSE = "TI"
+
+COMPATIBLE_MACHINE = "(omap3evm|am37x-evm|dm37x-evm|dm365-evm|da830-omapl138-evm.conf)"
+
+require ti-paths.inc
+
+SRC_URI = "\
+ file://setup/setup.sh \
+ file://setup/common.sh \
+ file://setup/setup-host-check.sh \
+ file://setup/setup-minicom.sh \
+ file://setup/setup-package-install.sh \
+ file://setup/setup-targetfs-nfs.sh \
+ file://setup/setup-tftp.sh \
+ file://setup/setup-uboot-env.sh \
+"
+
+PR = "r11"
+
+do_install () {
+ install -d ${D}/${installdir}/bin
+ install -m 0755 ${WORKDIR}/setup/* ${D}/${installdir}/bin/
+ # Place the setup.sh script one directory higher
+ mv ${D}/${installdir}/bin/setup.sh ${D}/${installdir}/setup.sh
+}
+
+PACKAGE_ARCH = "${MACHINE_ARCH}"
+
+FILES_${PN} = "${installdir}/*"
diff --git a/recipes/ti/ti-tisdk-setup/am37x-evm/setup/setup-uboot-env.sh b/recipes/ti/ti-tisdk-setup/am37x-evm/setup/setup-uboot-env.sh
new file mode 100644
index 0000000..009928d
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/am37x-evm/setup/setup-uboot-env.sh
@@ -0,0 +1,217 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the u-boot variables for booting the EVM."
+
+ipdefault=`ifconfig | grep 'inet addr:'| grep -v '127.0.0.1' | cut -d: -f2 | awk '{ print $1 }'`
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+prompt="EVM #"
+
+echo "Autodetected the following ip address of your host, correct it if necessary"
+read -p "[ $ipdefault ] " ip
+echo
+
+if [ ! -n "$ip" ]; then
+ ip=$ipdefault
+fi
+
+if [ -f $cwd/../.targetfs ]; then
+ rootpath=`cat $cwd/../.targetfs`
+else
+ echo "Where is your target filesystem extracted?"
+ read -p "[ ${HOME}/targetfs ]" rootpath
+
+ if [ ! -n "$rootpath" ]; then
+ rootpath="${HOME}/targetfs"
+ fi
+ echo
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimagedefault=`basename $uimagesrc`
+
+baseargs="console=ttyS0,115200n8 rw mem=99M mpurate=1000"
+videoargs1="omap_vout.vid1_static_vrfb_alloc=y"
+videoargs2="omapfb.vrfb=y vram=20M omapfb.vram=0:20M"
+videoargs3="omapfb.mode=dvi:720x480MR-16@60"
+videoargs="$videoargs1 $videoargs2 $videoargs3"
+fssdargs="root=/dev/mmcblk0p2 rootfstype=ext3"
+fsnfsargs="root=/dev/nfs nfsroot=$ip:$rootpath"
+
+echo "Select Linux kernel location:"
+echo " 1: TFTP"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " kernel
+
+if [ ! -n "$kernel" ]; then
+ kernel="1"
+fi
+
+echo
+echo "Select root file system location:"
+echo " 1: NFS"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " fs
+
+if [ ! -n "$fs" ]; then
+ fs="1"
+fi
+
+if [ "$kernel" -eq "1" ]; then
+ echo
+ echo "Available kernel images in /tftproot:"
+ for file in /tftpboot/*; do
+ basefile=`basename $file`
+ echo " $basefile"
+ done
+ echo
+ echo "Which kernel image do you want to boot from TFTP?"
+ read -p "[ $uimagedefault ] " uimage
+
+ if [ ! -n "$uimage" ]; then
+ uimage=$uimagedefault
+ fi
+
+ bootcmd="setenv bootcmd 'dhcp;setenv serverip $ip;tftpboot;bootm'"
+ serverip="setenv serverip $ip"
+ bootfile="setenv bootfile $uimage"
+
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ cfg="uimage-tftp_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ cfg="uimage-tftp_fs-sd"
+ fi
+else
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-sd"
+ fi
+fi
+
+echo
+echo "Resulting u-boot variable settings:"
+echo
+echo "setenv bootdelay 4"
+echo "setenv baudrate 115200"
+echo $bootargs
+echo $bootcmd
+
+if [ -n "$serverip" ]; then
+ echo "setenv autoload no"
+ echo $serverip
+fi
+
+if [ -n "$bootfile" ]; then
+ echo $bootfile
+fi
+echo "--------------------------------------------------------------------------------"
+
+do_expect() {
+ echo "expect {" >> $3
+ check_status
+ echo " $1" >> $3
+ check_status
+ echo "}" >> $3
+ check_status
+ echo $2 >> $3
+ check_status
+ echo >> $3
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Would you like to create a minicom script with the above parameters (y/n)?"
+read -p "[ y ] " minicom
+echo
+
+if [ ! -n "$minicom" ]; then
+ minicom="y"
+fi
+
+if [ "$minicom" == "y" ]; then
+ minicomfile=setup_$platform_$cfg.minicom
+ minicomfilepath=$cwd/../$minicomfile
+
+ if [ -f $minicomfilepath ]; then
+ echo "Moving existing $minicomfile to $minicomfile.old"
+ mv $minicomfilepath $minicomfilepath.old
+ check_status
+ fi
+
+ timeout=300
+ echo "timeout $timeout" >> $minicomfilepath
+ echo "verbose on" >> $minicomfilepath
+ echo >> $minicomfilepath
+ do_expect "\"stop autoboot:\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootdelay 4\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv baudrate 115200\"" $minicomfilepath
+ do_expect "\"ENTER ...\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootargs \$\{bootargs\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootargs $baseargs \c\"" $minicomfilepath
+ echo "send \"$videoargs1 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs2 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs3 \c\"" >> $minicomfilepath
+# echo "send \"$videoargs4 \c\"" >> $minicomfilepath
+ if [ "$fs" -eq "1" ]; then
+ echo "send \"$fsnfsargs \c\"" >> $minicomfilepath
+ echo "send \"ip=dhcp\"" >> $minicomfilepath
+ else
+ echo "send \"$fssdargs \c\"" >> $minicomfilepath
+ echo "send \"ip=off\"" >> $minicomfilepath
+ fi
+ if [ "$kernel" -eq "1" ]; then
+ do_expect "\"$prompt\"" "send \"setenv autoload no\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldserverip \$\{serverip\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$serverip\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootfile \$\{bootfile\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootfile\"" $minicomfilepath
+ fi
+ do_expect "\"$prompt\"" "send \"setenv oldbootcmd \$\{bootcmd\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootcmd\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"saveenv\"" $minicomfilepath
+ do_expect "\"$prompt\"" "! killall -s SIGHUP minicom" $minicomfilepath
+
+ echo "Successfully wrote $minicomfile"
+ echo
+ echo "Would you like to run the setup script now (y/n)? This requires you to connect"
+ echo "the RS-232 cable between your host and EVM as well as your ethernet cable as"
+ echo "described in the Quick Start Guide. Once answering 'y' on the prompt below"
+ echo "you will have $timeout seconds to connect the board and power cycle it"
+ echo "before the setup times out"
+ echo
+ echo "After successfully executing this script, your EVM will be set up. You will be "
+ echo "able to connect to it by executing 'minicom -w' or if you prefer a windows host"
+ echo "you can set up Tera Term as explained in the Software Developer's Guide."
+ echo "If you connect minicom or Tera Term and power cycle the board Linux will boot."
+ echo
+ read -p "[ y ] " minicomsetup
+
+ if [ ! -n "$minicomsetup" ]; then
+ minicomsetup="y"
+ fi
+
+ if [ "$minicomsetup" == "y" ]; then
+ pushd $cwd/..
+ check_status
+ minicom -S $minicomfile
+ popd >> /dev/null
+ check_status
+
+ fi
+
+ echo "You can manually run minicom in the future with this setup script using: minicom -S $minicomfile"
+fi
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/dm365-evm/setup/setup-uboot-env.sh b/recipes/ti/ti-tisdk-setup/dm365-evm/setup/setup-uboot-env.sh
new file mode 100644
index 0000000..98089fc
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/dm365-evm/setup/setup-uboot-env.sh
@@ -0,0 +1,237 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the u-boot variables for booting the EVM."
+
+ipdefault=`ifconfig | grep 'inet addr:'| grep -v '127.0.0.1' | cut -d: -f2 | awk '{ print $1 }'`
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+prompt="EVM >"
+
+echo "Autodetected the following ip address of your host, correct it if necessary"
+read -p "[ $ipdefault ] " ip
+echo
+
+if [ ! -n "$ip" ]; then
+ ip=$ipdefault
+fi
+
+if [ -f $cwd/../.targetfs ]; then
+ rootpath=`cat $cwd/../.targetfs`
+else
+ echo "Where is your target filesystem extracted?"
+ read -p "[ ${HOME}/targetfs ]" rootpath
+
+ if [ ! -n "$rootpath" ]; then
+ rootpath="${HOME}/targetfs"
+ fi
+ echo
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimagedefault=`basename $uimagesrc`
+
+baseargs="console=ttyS0,115200n8 rw mem=59M"
+videoargs1="video=davincifb:vid0=OFF:vid1=OFF:osd0=720x576x16,4050K"
+videoargs2="dm365_imp.oper_mode=0 davinci_capture.device_type=4"
+videoargs3="davinci_display.cont2_bufsize=6291456"
+videoargs4="vpfe_capture.cont_bufoffset=6291456"
+videoargs5="vpfe_capture.cont_bufsize=6291456"
+videoargs6="davinci_enc_mngr.ch0_output=COMPONENT"
+videoargs7="davinci_enc_mngr.ch0_mode=480P-60"
+videoargs="$videoargs1 $videoargs2 $videoargs3 $videoargs4 $videoargs5 $videoargs6 $videoargs7"
+fssdargs="root=/dev/mmcblk0p2 rootwait"
+fsnfsargs="root=/dev/nfs nfsroot=$ip:$rootpath"
+
+#echo "Select UBL location:"
+#echo " 1: flash"
+#echo " 2: SD card"
+#echo
+#read -p "[ 1 ] " ubl
+
+#if [ ! -n "$ubl" ]; then
+# ubl="1"
+#fi
+
+echo "Select Linux kernel location:"
+echo " 1: TFTP"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " kernel
+
+if [ ! -n "$kernel" ]; then
+ kernel="1"
+fi
+
+echo
+echo "Select root file system location:"
+echo " 1: NFS"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " fs
+
+if [ ! -n "$fs" ]; then
+ fs="1"
+fi
+
+if [ "$kernel" -eq "1" ]; then
+ echo
+ echo "Available kernel images in /tftproot:"
+ for file in /tftpboot/*; do
+ basefile=`basename $file`
+ echo " $basefile"
+ done
+ echo
+ echo "Which kernel image do you want to boot from TFTP?"
+ read -p "[ $uimagedefault ] " uimage
+
+ if [ ! -n "$uimage" ]; then
+ uimage=$uimagedefault
+ fi
+
+ bootcmd="setenv bootcmd 'dhcp;setenv serverip $ip;tftpboot;bootm'"
+ serverip="setenv serverip $ip"
+ bootfile="setenv bootfile $uimage"
+
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ cfg="uimage-tftp_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ cfg="uimage-tftp_fs-sd"
+ fi
+else
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ bootcmd="setenv bootcmd 'bootm 0x80700000'"
+ cfg="uimage-sd_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ bootcmd="setenv bootcmd 'bootm 0x80700000'"
+ cfg="uimage-sd_fs-sd"
+ fi
+fi
+
+echo
+echo "Resulting u-boot variable settings:"
+echo
+echo "setenv bootdelay 4"
+echo "setenv baudrate 115200"
+echo $bootargs
+echo $bootcmd
+
+if [ -n "$serverip" ]; then
+ echo "setenv autoload no"
+ echo $serverip
+fi
+
+if [ -n "$bootfile" ]; then
+ echo $bootfile
+fi
+echo "--------------------------------------------------------------------------------"
+
+do_expect() {
+ echo "expect {" >> $3
+ check_status
+ echo " $1" >> $3
+ check_status
+ echo "}" >> $3
+ check_status
+ echo $2 >> $3
+ check_status
+ echo >> $3
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Would you like to create a minicom script with the above parameters (y/n)?"
+read -p "[ y ] " minicom
+echo
+
+if [ ! -n "$minicom" ]; then
+ minicom="y"
+fi
+
+if [ "$minicom" == "y" ]; then
+ minicomfile=setup_$platform_$cfg.minicom
+ minicomfilepath=$cwd/../$minicomfile
+
+ if [ -f $minicomfilepath ]; then
+ echo "Moving existing $minicomfile to $minicomfile.old"
+ mv $minicomfilepath $minicomfilepath.old
+ check_status
+ fi
+
+ timeout=300
+ echo "timeout $timeout" >> $minicomfilepath
+ echo "verbose on" >> $minicomfilepath
+ echo >> $minicomfilepath
+#if [ "$ubl" -eq "2" ]; then
+# do_expect "\"\ > \"" "send \"1\"" $minicomfilepath
+#fi
+ do_expect "\"stop autoboot:\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootdelay 4\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv baudrate 115200\"" $minicomfilepath
+ do_expect "\"ENTER ...\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootargs \$\{bootargs\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootargs $baseargs \c\"" $minicomfilepath
+ echo "send \"$videoargs1 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs2 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs3 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs4 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs5 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs6 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs7 \c\"" >> $minicomfilepath
+ if [ "$fs" -eq "1" ]; then
+ echo "send \"$fsnfsargs \c\"" >> $minicomfilepath
+ echo "send \"ip=dhcp\"" >> $minicomfilepath
+ else
+ echo "send \"$fssdargs \c\"" >> $minicomfilepath
+ echo "send \"ip=off\"" >> $minicomfilepath
+ fi
+ if [ "$kernel" -eq "1" ]; then
+ do_expect "\"$prompt\"" "send \"setenv autoload no\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldserverip \$\{serverip\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$serverip\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootfile \$\{bootfile\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootfile\"" $minicomfilepath
+ fi
+ do_expect "\"$prompt\"" "send \"setenv oldbootcmd \$\{bootcmd\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootcmd\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"saveenv\"" $minicomfilepath
+ do_expect "\"$prompt\"" "! killall -s SIGHUP minicom" $minicomfilepath
+
+ echo "Successfully wrote $minicomfile"
+ echo
+ echo "Would you like to run the setup script now (y/n)? This requires you to connect"
+ echo "the RS-232 cable between your host and EVM as well as your ethernet cable as"
+ echo "described in the Quick Start Guide. Once answering 'y' on the prompt below"
+ echo "you will have $timeout seconds to connect the board and power cycle it"
+ echo "before the setup times out"
+ echo
+ echo "After successfully executing this script, your EVM will be set up. You will be "
+ echo "able to connect to it by executing 'minicom -w' or if you prefer a windows host"
+ echo "you can set up Tera Term as explained in the Software Developer's Guide."
+ echo "If you connect minicom or Tera Term and power cycle the board Linux will boot."
+ echo
+ read -p "[ y ] " minicomsetup
+
+ if [ ! -n "$minicomsetup" ]; then
+ minicomsetup="y"
+ fi
+
+ if [ "$minicomsetup" == "y" ]; then
+ pushd $cwd/..
+ check_status
+ minicom -S $minicomfile
+ popd >> /dev/null
+ check_status
+
+ fi
+
+ echo "You can manually run minicom in the future with this setup script using: minicom -S $minicomfile"
+fi
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/dm37x-evm/setup/setup-uboot-env.sh b/recipes/ti/ti-tisdk-setup/dm37x-evm/setup/setup-uboot-env.sh
new file mode 100644
index 0000000..009928d
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/dm37x-evm/setup/setup-uboot-env.sh
@@ -0,0 +1,217 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the u-boot variables for booting the EVM."
+
+ipdefault=`ifconfig | grep 'inet addr:'| grep -v '127.0.0.1' | cut -d: -f2 | awk '{ print $1 }'`
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+prompt="EVM #"
+
+echo "Autodetected the following ip address of your host, correct it if necessary"
+read -p "[ $ipdefault ] " ip
+echo
+
+if [ ! -n "$ip" ]; then
+ ip=$ipdefault
+fi
+
+if [ -f $cwd/../.targetfs ]; then
+ rootpath=`cat $cwd/../.targetfs`
+else
+ echo "Where is your target filesystem extracted?"
+ read -p "[ ${HOME}/targetfs ]" rootpath
+
+ if [ ! -n "$rootpath" ]; then
+ rootpath="${HOME}/targetfs"
+ fi
+ echo
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimagedefault=`basename $uimagesrc`
+
+baseargs="console=ttyS0,115200n8 rw mem=99M mpurate=1000"
+videoargs1="omap_vout.vid1_static_vrfb_alloc=y"
+videoargs2="omapfb.vrfb=y vram=20M omapfb.vram=0:20M"
+videoargs3="omapfb.mode=dvi:720x480MR-16@60"
+videoargs="$videoargs1 $videoargs2 $videoargs3"
+fssdargs="root=/dev/mmcblk0p2 rootfstype=ext3"
+fsnfsargs="root=/dev/nfs nfsroot=$ip:$rootpath"
+
+echo "Select Linux kernel location:"
+echo " 1: TFTP"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " kernel
+
+if [ ! -n "$kernel" ]; then
+ kernel="1"
+fi
+
+echo
+echo "Select root file system location:"
+echo " 1: NFS"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " fs
+
+if [ ! -n "$fs" ]; then
+ fs="1"
+fi
+
+if [ "$kernel" -eq "1" ]; then
+ echo
+ echo "Available kernel images in /tftproot:"
+ for file in /tftpboot/*; do
+ basefile=`basename $file`
+ echo " $basefile"
+ done
+ echo
+ echo "Which kernel image do you want to boot from TFTP?"
+ read -p "[ $uimagedefault ] " uimage
+
+ if [ ! -n "$uimage" ]; then
+ uimage=$uimagedefault
+ fi
+
+ bootcmd="setenv bootcmd 'dhcp;setenv serverip $ip;tftpboot;bootm'"
+ serverip="setenv serverip $ip"
+ bootfile="setenv bootfile $uimage"
+
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ cfg="uimage-tftp_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ cfg="uimage-tftp_fs-sd"
+ fi
+else
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-sd"
+ fi
+fi
+
+echo
+echo "Resulting u-boot variable settings:"
+echo
+echo "setenv bootdelay 4"
+echo "setenv baudrate 115200"
+echo $bootargs
+echo $bootcmd
+
+if [ -n "$serverip" ]; then
+ echo "setenv autoload no"
+ echo $serverip
+fi
+
+if [ -n "$bootfile" ]; then
+ echo $bootfile
+fi
+echo "--------------------------------------------------------------------------------"
+
+do_expect() {
+ echo "expect {" >> $3
+ check_status
+ echo " $1" >> $3
+ check_status
+ echo "}" >> $3
+ check_status
+ echo $2 >> $3
+ check_status
+ echo >> $3
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Would you like to create a minicom script with the above parameters (y/n)?"
+read -p "[ y ] " minicom
+echo
+
+if [ ! -n "$minicom" ]; then
+ minicom="y"
+fi
+
+if [ "$minicom" == "y" ]; then
+ minicomfile=setup_$platform_$cfg.minicom
+ minicomfilepath=$cwd/../$minicomfile
+
+ if [ -f $minicomfilepath ]; then
+ echo "Moving existing $minicomfile to $minicomfile.old"
+ mv $minicomfilepath $minicomfilepath.old
+ check_status
+ fi
+
+ timeout=300
+ echo "timeout $timeout" >> $minicomfilepath
+ echo "verbose on" >> $minicomfilepath
+ echo >> $minicomfilepath
+ do_expect "\"stop autoboot:\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootdelay 4\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv baudrate 115200\"" $minicomfilepath
+ do_expect "\"ENTER ...\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootargs \$\{bootargs\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootargs $baseargs \c\"" $minicomfilepath
+ echo "send \"$videoargs1 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs2 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs3 \c\"" >> $minicomfilepath
+# echo "send \"$videoargs4 \c\"" >> $minicomfilepath
+ if [ "$fs" -eq "1" ]; then
+ echo "send \"$fsnfsargs \c\"" >> $minicomfilepath
+ echo "send \"ip=dhcp\"" >> $minicomfilepath
+ else
+ echo "send \"$fssdargs \c\"" >> $minicomfilepath
+ echo "send \"ip=off\"" >> $minicomfilepath
+ fi
+ if [ "$kernel" -eq "1" ]; then
+ do_expect "\"$prompt\"" "send \"setenv autoload no\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldserverip \$\{serverip\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$serverip\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootfile \$\{bootfile\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootfile\"" $minicomfilepath
+ fi
+ do_expect "\"$prompt\"" "send \"setenv oldbootcmd \$\{bootcmd\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootcmd\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"saveenv\"" $minicomfilepath
+ do_expect "\"$prompt\"" "! killall -s SIGHUP minicom" $minicomfilepath
+
+ echo "Successfully wrote $minicomfile"
+ echo
+ echo "Would you like to run the setup script now (y/n)? This requires you to connect"
+ echo "the RS-232 cable between your host and EVM as well as your ethernet cable as"
+ echo "described in the Quick Start Guide. Once answering 'y' on the prompt below"
+ echo "you will have $timeout seconds to connect the board and power cycle it"
+ echo "before the setup times out"
+ echo
+ echo "After successfully executing this script, your EVM will be set up. You will be "
+ echo "able to connect to it by executing 'minicom -w' or if you prefer a windows host"
+ echo "you can set up Tera Term as explained in the Software Developer's Guide."
+ echo "If you connect minicom or Tera Term and power cycle the board Linux will boot."
+ echo
+ read -p "[ y ] " minicomsetup
+
+ if [ ! -n "$minicomsetup" ]; then
+ minicomsetup="y"
+ fi
+
+ if [ "$minicomsetup" == "y" ]; then
+ pushd $cwd/..
+ check_status
+ minicom -S $minicomfile
+ popd >> /dev/null
+ check_status
+
+ fi
+
+ echo "You can manually run minicom in the future with this setup script using: minicom -S $minicomfile"
+fi
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/omap3evm/setup/setup-uboot-env.sh b/recipes/ti/ti-tisdk-setup/omap3evm/setup/setup-uboot-env.sh
new file mode 100644
index 0000000..0cbd7bb
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/omap3evm/setup/setup-uboot-env.sh
@@ -0,0 +1,217 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the u-boot variables for booting the EVM."
+
+ipdefault=`ifconfig | grep 'inet addr:'| grep -v '127.0.0.1' | cut -d: -f2 | awk '{ print $1 }'`
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+prompt="EVM #"
+
+echo "Autodetected the following ip address of your host, correct it if necessary"
+read -p "[ $ipdefault ] " ip
+echo
+
+if [ ! -n "$ip" ]; then
+ ip=$ipdefault
+fi
+
+if [ -f $cwd/../.targetfs ]; then
+ rootpath=`cat $cwd/../.targetfs`
+else
+ echo "Where is your target filesystem extracted?"
+ read -p "[ ${HOME}/targetfs ]" rootpath
+
+ if [ ! -n "$rootpath" ]; then
+ rootpath="${HOME}/targetfs"
+ fi
+ echo
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimagedefault=`basename $uimagesrc`
+
+baseargs="console=ttyS0,115200n8 rw mem=99M mpurate=720"
+videoargs1="omap_vout.vid1_static_vrfb_alloc=y"
+videoargs2="omapfb.vrfb=y vram=20M omapfb.vram=0:20M"
+videoargs3="omapfb.mode=dvi:720x480MR-16@60"
+videoargs="$videoargs1 $videoargs2 $videoargs3"
+fssdargs="root=/dev/mmcblk0p2 rootfstype=ext3"
+fsnfsargs="root=/dev/nfs nfsroot=$ip:$rootpath"
+
+echo "Select Linux kernel location:"
+echo " 1: TFTP"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " kernel
+
+if [ ! -n "$kernel" ]; then
+ kernel="1"
+fi
+
+echo
+echo "Select root file system location:"
+echo " 1: NFS"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " fs
+
+if [ ! -n "$fs" ]; then
+ fs="1"
+fi
+
+if [ "$kernel" -eq "1" ]; then
+ echo
+ echo "Available kernel images in /tftproot:"
+ for file in /tftpboot/*; do
+ basefile=`basename $file`
+ echo " $basefile"
+ done
+ echo
+ echo "Which kernel image do you want to boot from TFTP?"
+ read -p "[ $uimagedefault ] " uimage
+
+ if [ ! -n "$uimage" ]; then
+ uimage=$uimagedefault
+ fi
+
+ bootcmd="setenv bootcmd 'dhcp;setenv serverip $ip;tftpboot;bootm'"
+ serverip="setenv serverip $ip"
+ bootfile="setenv bootfile $uimage"
+
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ cfg="uimage-tftp_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ cfg="uimage-tftp_fs-sd"
+ fi
+else
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ bootcmd="setenv bootcmd 'mmc init;fatload mmc 0 0x82000000 uImage;bootm 0x82000000'"
+ cfg="uimage-sd_fs-sd"
+ fi
+fi
+
+echo
+echo "Resulting u-boot variable settings:"
+echo
+echo "setenv bootdelay 4"
+echo "setenv baudrate 115200"
+echo $bootargs
+echo $bootcmd
+
+if [ -n "$serverip" ]; then
+ echo "setenv autoload no"
+ echo $serverip
+fi
+
+if [ -n "$bootfile" ]; then
+ echo $bootfile
+fi
+echo "--------------------------------------------------------------------------------"
+
+do_expect() {
+ echo "expect {" >> $3
+ check_status
+ echo " $1" >> $3
+ check_status
+ echo "}" >> $3
+ check_status
+ echo $2 >> $3
+ check_status
+ echo >> $3
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Would you like to create a minicom script with the above parameters (y/n)?"
+read -p "[ y ] " minicom
+echo
+
+if [ ! -n "$minicom" ]; then
+ minicom="y"
+fi
+
+if [ "$minicom" == "y" ]; then
+ minicomfile=setup_$platform_$cfg.minicom
+ minicomfilepath=$cwd/../$minicomfile
+
+ if [ -f $minicomfilepath ]; then
+ echo "Moving existing $minicomfile to $minicomfile.old"
+ mv $minicomfilepath $minicomfilepath.old
+ check_status
+ fi
+
+ timeout=300
+ echo "timeout $timeout" >> $minicomfilepath
+ echo "verbose on" >> $minicomfilepath
+ echo >> $minicomfilepath
+ do_expect "\"stop autoboot:\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootdelay 4\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv baudrate 115200\"" $minicomfilepath
+ do_expect "\"ENTER ...\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootargs \$\{bootargs\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootargs $baseargs \c\"" $minicomfilepath
+ echo "send \"$videoargs1 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs2 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs3 \c\"" >> $minicomfilepath
+# echo "send \"$videoargs4 \c\"" >> $minicomfilepath
+ if [ "$fs" -eq "1" ]; then
+ echo "send \"$fsnfsargs \c\"" >> $minicomfilepath
+ echo "send \"ip=dhcp\"" >> $minicomfilepath
+ else
+ echo "send \"$fssdargs \c\"" >> $minicomfilepath
+ echo "send \"ip=off\"" >> $minicomfilepath
+ fi
+ if [ "$kernel" -eq "1" ]; then
+ do_expect "\"$prompt\"" "send \"setenv autoload no\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldserverip \$\{serverip\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$serverip\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootfile \$\{bootfile\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootfile\"" $minicomfilepath
+ fi
+ do_expect "\"$prompt\"" "send \"setenv oldbootcmd \$\{bootcmd\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootcmd\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"saveenv\"" $minicomfilepath
+ do_expect "\"$prompt\"" "! killall -s SIGHUP minicom" $minicomfilepath
+
+ echo "Successfully wrote $minicomfile"
+ echo
+ echo "Would you like to run the setup script now (y/n)? This requires you to connect"
+ echo "the RS-232 cable between your host and EVM as well as your ethernet cable as"
+ echo "described in the Quick Start Guide. Once answering 'y' on the prompt below"
+ echo "you will have $timeout seconds to connect the board and power cycle it"
+ echo "before the setup times out"
+ echo
+ echo "After successfully executing this script, your EVM will be set up. You will be "
+ echo "able to connect to it by executing 'minicom -w' or if you prefer a windows host"
+ echo "you can set up Tera Term as explained in the Software Developer's Guide."
+ echo "If you connect minicom or Tera Term and power cycle the board Linux will boot."
+ echo
+ read -p "[ y ] " minicomsetup
+
+ if [ ! -n "$minicomsetup" ]; then
+ minicomsetup="y"
+ fi
+
+ if [ "$minicomsetup" == "y" ]; then
+ pushd $cwd/..
+ check_status
+ minicom -S $minicomfile
+ popd >> /dev/null
+ check_status
+
+ fi
+
+ echo "You can manually run minicom in the future with this setup script using: minicom -S $minicomfile"
+fi
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/omapl138/setup/setup-uboot-env.sh b/recipes/ti/ti-tisdk-setup/omapl138/setup/setup-uboot-env.sh
new file mode 100644
index 0000000..f089880
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/omapl138/setup/setup-uboot-env.sh
@@ -0,0 +1,213 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the u-boot variables for booting the EVM."
+
+ipdefault=`ifconfig | grep 'inet addr:'| grep -v '127.0.0.1' | cut -d: -f2 | awk '{ print $1 }'`
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+prompt=" >"
+
+echo "Autodetected the following ip address of your host, correct it if necessary"
+read -p "[ $ipdefault ] " ip
+echo
+
+if [ ! -n "$ip" ]; then
+ ip=$ipdefault
+fi
+
+if [ -f $cwd/../.targetfs ]; then
+ rootpath=`cat $cwd/../.targetfs`
+else
+ echo "Where is your target filesystem extracted?"
+ read -p "[ ${HOME}/targetfs ]" rootpath
+
+ if [ ! -n "$rootpath" ]; then
+ rootpath="${HOME}/targetfs"
+ fi
+ echo
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimagedefault=`basename $uimagesrc`
+
+baseargs="console=ttyS2,115200n8 noinitrd rw mem=32M@0xc0000000"
+fssdargs="root=/dev/mmcblk0p2 rootfstype=ext3 rootwait"
+fsnfsargs="root=/dev/nfs nfsroot=$ip:$rootpath,nolock"
+
+echo "Select Linux kernel location:"
+echo " 1: TFTP"
+echo " 2: flash"
+echo
+read -p "[ 1 ] " kernel
+
+if [ ! -n "$kernel" ]; then
+ kernel="1"
+fi
+
+echo
+echo "Select root file system location:"
+echo " 1: NFS"
+echo " 2: SD card"
+echo
+read -p "[ 1 ] " fs
+
+if [ ! -n "$fs" ]; then
+ fs="1"
+fi
+
+if [ "$kernel" -eq "1" ]; then
+ echo
+ echo "Available kernel images in /tftproot:"
+ for file in /tftpboot/*; do
+ basefile=`basename $file`
+ echo " $basefile"
+ done
+ echo
+ echo "Which kernel image do you want to boot from TFTP?"
+ read -p "[ $uimagedefault ] " uimage
+
+ if [ ! -n "$uimage" ]; then
+ uimage=$uimagedefault
+ fi
+
+# bootcmd="setenv bootcmd 'dhcp;bootm'"
+ bootcmd="setenv bootcmd 'dhcp;setenv serverip $ip;tftpboot;bootm'"
+ serverip="setenv serverip $ip"
+ bootfile="setenv bootfile $uimage"
+
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ cfg="uimage-tftp_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ cfg="uimage-tftp_fs-sd"
+ fi
+else
+ if [ "$fs" -eq "1" ]; then
+ bootargs="setenv bootargs $baseargs $videoargs $fsnfsargs ip=dhcp"
+ bootcmd="setenv bootcmd 'sf probe 0; sf read 0xc0700000 0x80000 0x280000; bootm 0xc0700000'"
+ cfg="uimage-flash_fs-nfs"
+ else
+ bootargs="setenv bootargs $baseargs $videoargs $fssdargs ip=off"
+ bootcmd="setenv bootcmd 'sf probe 0; sf read 0xc0700000 0x80000 0x280000; bootm 0xc0700000'"
+ cfg="uimage-flash_fs-sd"
+ fi
+fi
+
+echo
+echo "Resulting u-boot variable settings:"
+echo
+echo "setenv bootdelay 4"
+echo "setenv baudrate 115200"
+echo $bootargs
+echo $bootcmd
+
+if [ -n "$serverip" ]; then
+ echo "setenv autoload no"
+ echo $serverip
+fi
+
+if [ -n "$bootfile" ]; then
+ echo $bootfile
+fi
+echo "--------------------------------------------------------------------------------"
+
+do_expect() {
+ echo "expect {" >> $3
+ check_status
+ echo " $1" >> $3
+ check_status
+ echo "}" >> $3
+ check_status
+ echo $2 >> $3
+ check_status
+ echo >> $3
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Would you like to create a minicom script with the above parameters (y/n)?"
+read -p "[ y ] " minicom
+echo
+
+if [ ! -n "$minicom" ]; then
+ minicom="y"
+fi
+
+if [ "$minicom" == "y" ]; then
+ minicomfile=setup_$platform_$cfg.minicom
+ minicomfilepath=$cwd/../$minicomfile
+
+ if [ -f $minicomfilepath ]; then
+ echo "Moving existing $minicomfile to $minicomfile.old"
+ mv $minicomfilepath $minicomfilepath.old
+ check_status
+ fi
+
+ timeout=300
+ echo "timeout $timeout" >> $minicomfilepath
+ echo "verbose on" >> $minicomfilepath
+ echo >> $minicomfilepath
+ do_expect "\"stop autoboot:\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootdelay 4\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv baudrate 115200\"" $minicomfilepath
+ do_expect "\"ENTER ...\"" "send \"\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldbootargs \$\{bootargs\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv bootargs $baseargs \c\"" $minicomfilepath
+ echo "send \"$videoargs1 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs2 \c\"" >> $minicomfilepath
+ echo "send \"$videoargs3 \c\"" >> $minicomfilepath
+ if [ "$fs" -eq "1" ]; then
+ echo "send \"$fsnfsargs \c\"" >> $minicomfilepath
+ echo "send \"ip=dhcp\"" >> $minicomfilepath
+ else
+ echo "send \"$fssdargs \c\"" >> $minicomfilepath
+ echo "send \"ip=off\"" >> $minicomfilepath
+ fi
+ if [ "$kernel" -eq "1" ]; then
+ do_expect "\"$prompt\"" "send \"setenv autoload no\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"setenv oldserverip \$\{serverip\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$serverip\"" $minicomfilepath
+# do_expect "\"$prompt\"" "send \"setenv oldbootfile \$\{bootfile\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootfile\"" $minicomfilepath
+ fi
+ do_expect "\"$prompt\"" "send \"setenv oldbootcmd \$\{bootcmd\}\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"$bootcmd\"" $minicomfilepath
+ do_expect "\"$prompt\"" "send \"saveenv\"" $minicomfilepath
+ do_expect "\"$prompt\"" "! killall -s SIGHUP minicom" $minicomfilepath
+
+ echo "Successfully wrote $minicomfile"
+ echo
+ echo "Would you like to run the setup script now (y/n)? This requires you to connect"
+ echo "the RS-232 cable between your host and EVM as well as your ethernet cable as"
+ echo "described in the Quick Start Guide. Once answering 'y' on the prompt below"
+ echo "you will have $timeout seconds to connect the board and power cycle it"
+ echo "before the setup times out."
+ echo
+ echo "After successfully executing this script, your EVM will be set up. You will be "
+ echo "able to connect to it by executing 'minicom -w' or if you prefer a windows host"
+ echo "you can set up Tera Term as explained in the Software Developer's Guide."
+ echo "If you connect minicom or Tera Term and power cycle the board Linux will boot."
+ echo
+ read -p "[ y ] " minicomsetup
+
+ if [ ! -n "$minicomsetup" ]; then
+ minicomsetup="y"
+ fi
+
+ if [ "$minicomsetup" == "y" ]; then
+ pushd $cwd/..
+ check_status
+ minicom -S $minicomfile
+ popd >> /dev/null
+ check_status
+
+ fi
+
+ echo "You can manually run minicom in the future with this setup script using: minicom -S $minicomfile"
+fi
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/setup/common.sh b/recipes/ti/ti-tisdk-setup/setup/common.sh
new file mode 100644
index 0000000..ccd5b47
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/common.sh
@@ -0,0 +1,9 @@
+#!/bin/sh
+
+check_status() {
+ ret=$?
+ if [ "$ret" -ne "0" ]; then
+ echo "Failed setup, aborting.."
+ exit 1
+ fi
+}
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup-host-check.sh b/recipes/ti/ti-tisdk-setup/setup/setup-host-check.sh
new file mode 100644
index 0000000..93352ed
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup-host-check.sh
@@ -0,0 +1,13 @@
+#!/bin/sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "Verifying Linux host distribution"
+host=`lsb_release -a 2>/dev/null | grep Codename: | awk {'print $2'}`
+if [ "$host" != "lucid" ]; then
+ echo "Unsupported host machine, only Ubuntu 10.04 LTS supported"
+ exit 1
+fi
+echo "Ubuntu 10.04 LTS found successfully, continuing.."
+echo "--------------------------------------------------------------------------------"
+echo
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup-minicom.sh b/recipes/ti/ti-tisdk-setup/setup/setup-minicom.sh
new file mode 100644
index 0000000..f5f4125
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup-minicom.sh
@@ -0,0 +1,51 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+portdefault="/dev/ttyS0"
+minicomcfg=${HOME}/.minirc.dfl
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up minicom (serial communication application) for"
+echo "DVSDK development"
+echo
+echo "Which serial port do you want to use with minicom?"
+read -p "[ $portdefault ] " port
+
+if [ ! -n "$port" ]; then
+ port=$portdefault
+fi
+
+if [ -f $minicomcfg ]; then
+ cp $minicomcfg $minicomcfg.old
+ echo
+ echo "Copied existing $minicomcfg to $minicomcfg.old"
+fi
+
+echo "pu port $port
+pu baudrate 115200
+pu bits 8
+pu parity N
+pu stopbits 1
+pu minit
+pu mreset
+pu mdialpre
+pu mdialsuf
+pu mdialpre2
+pu mdialsuf2
+pu mdialpre3
+pu mdialsuf3
+pu mconnect
+pu mnocon1 NO CARRIER
+pu mnocon2 BUSY
+pu mnocon3 NO DIALTONE
+pu mnocon4 VOICE
+pu rtscts No" | tee $minicomcfg > /dev/null
+check_status
+
+echo
+echo "Configuration saved to $minicomcfg. You can change it further from inside"
+echo "minicom, see the Software Development Guide for more information."
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup-package-install.sh b/recipes/ti/ti-tisdk-setup/setup/setup-package-install.sh
new file mode 100644
index 0000000..0011e08
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup-package-install.sh
@@ -0,0 +1,21 @@
+#!/bin/sh
+
+. `dirname $0`/common.sh
+
+cmd="sudo apt-get install xinetd tftpd nfs-kernel-server minicom build-essential libncurses5-dev"
+echo "--------------------------------------------------------------------------------"
+echo "This step will make sure you have the proper host support packages installed"
+echo "using the following command: $cmd"
+echo
+echo "Note! This command requires you to have administrator priviliges (sudo access) "
+echo "on your host."
+echo -n "Press return to continue"
+read
+
+echo
+$cmd
+check_status
+echo
+echo "Package verification and installation successfully completed"
+echo "--------------------------------------------------------------------------------"
+echo
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup-targetfs-nfs.sh b/recipes/ti/ti-tisdk-setup/setup/setup-targetfs-nfs.sh
new file mode 100644
index 0000000..f1873e7
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup-targetfs-nfs.sh
@@ -0,0 +1,79 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+dstdefault="${HOME}/targetfs"
+echo "--------------------------------------------------------------------------------"
+echo "In which directory do you want to keep your target filesystem?"
+read -p "[ $dstdefault ] " dst
+
+if [ ! -n "$dst" ]; then
+ dst=$dstdefault
+fi
+echo "--------------------------------------------------------------------------------"
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will extract the target filesystem to $dst"
+echo
+echo "Note! This command requires you to have administrator priviliges (sudo access) "
+echo "on your host."
+read -p "Press return to continue"
+
+if [ -d $dst ]; then
+ echo "$dst already exists, skipping extraction..."
+else
+ sudo mkdir -p $dst
+ check_status
+
+ fstar=`ls -1 $cwd/../filesystem/dvsdk*rootfs.tar.gz`
+ sudo tar xzf $fstar -C $dst
+ check_status
+fi
+echo $dst > $cwd/../.targetfs
+echo "--------------------------------------------------------------------------------"
+
+platform=`grep PLATFORM= $cwd/../Rules.make | cut -d= -f2`
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the DVSDK to install binaries in to:"
+echo " $dst/home/root/$platform"
+echo
+echo "The files will be available from /home/root/$platform on the target."
+echo
+echo "This setting can be changed later by editing Rules.make and changing the"
+echo "EXEC_DIR variable."
+echo
+read -p "Press return to continue"
+
+sed -i "s=EXEC_DIR\=.*$=EXEC_DIR\=$dst/home/root/$platform=g" $cwd/../Rules.make
+check_status
+
+echo "Rules.make edited successfully.."
+echo "--------------------------------------------------------------------------------"
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will export your target filesystem for NFS access."
+echo
+echo "Note! This command requires you to have administrator priviliges (sudo access) "
+echo "on your host."
+read -p "Press return to continue"
+
+grep $dst /etc/exports > /dev/null
+if [ "$?" -eq "0" ]; then
+ echo "$dst already NFS exported, skipping.."
+else
+ sudo chmod 666 /etc/exports
+ check_status
+ sudo echo "$dst *(rw,nohide,insecure,no_subtree_check,async,no_root_squash)" >> /etc/exports
+ check_status
+ sudo chmod 644 /etc/exports
+ check_status
+fi
+
+echo
+sudo /etc/init.d/nfs-kernel-server restart
+check_status
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup-tftp.sh b/recipes/ti/ti-tisdk-setup/setup/setup-tftp.sh
new file mode 100644
index 0000000..b597e37
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup-tftp.sh
@@ -0,0 +1,81 @@
+#!/bin/sh
+
+cwd=`dirname $0`
+. $cwd/common.sh
+
+tftpcfg=/etc/xinetd.d/tftp
+tftproot=/tftpboot
+
+tftp() {
+ echo "
+service tftp
+{
+protocol = udp
+port = 69
+socket_type = dgram
+wait = yes
+user = nobody
+server = /usr/sbin/in.tftpd
+server_args = $tftproot
+disable = no
+}
+" | sudo tee $tftpcfg > /dev/null
+ check_status
+ echo
+ echo "$tftpcfg successfully created"
+}
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "This step will set up the tftp server in the $tftproot directory."
+echo
+echo "Note! This command requires you to have administrator priviliges (sudo access) "
+echo "on your host."
+read -p "Press return to continue"
+
+if [ -d $tftproot ]; then
+ echo
+ echo "$tftproot already exists, not creating.."
+else
+ sudo mkdir -p $tftproot
+ check_status
+ sudo chmod 777 $tftproot
+ check_status
+ sudo chown nobody $tftproot
+ check_status
+fi
+
+uimagesrc=`ls -1 $cwd/../psp/prebuilt-images/uImage*.bin`
+uimage=`basename $uimagesrc`
+if [ -f $tftproot/$uimage ]; then
+ echo
+ echo "$tftproot/$uimage already exists, skipping copy.."
+else
+ sudo cp $uimagesrc $tftproot
+ check_status
+ echo
+ echo "Successfully copied $uimage to tftp root directory $tftproot"
+fi
+
+echo
+if [ -f $tftpcfg ]; then
+ echo "$tftpcfg already exists.."
+
+ grep "$tftproot" $tftpcfg > /dev/null
+ if [ "$?" -eq "0" ]; then
+ echo "$tftproot already exported for TFTP, skipping.."
+ else
+ echo "Copying old $tftpcfg to $tftpcfg.old"
+ sudo cp $tftpcfg $tftpcfg.old
+ check_status
+ tftp
+ fi
+else
+ tftp
+fi
+
+echo
+echo "Restarting tftp server"
+sudo /etc/init.d/xinetd stop
+sudo /etc/init.d/xinetd start
+echo "--------------------------------------------------------------------------------"
diff --git a/recipes/ti/ti-tisdk-setup/setup/setup.sh b/recipes/ti/ti-tisdk-setup/setup/setup.sh
new file mode 100644
index 0000000..3701287
--- /dev/null
+++ b/recipes/ti/ti-tisdk-setup/setup/setup.sh
@@ -0,0 +1,35 @@
+#!/bin/sh
+
+echo
+echo "--------------------------------------------------------------------------------"
+echo "DVSDK setup script"
+echo
+echo "This script will set up your development host for dvsdk development."
+echo "Parts of this script require administrator priviliges (sudo access)."
+echo "--------------------------------------------------------------------------------"
+
+cwd=`dirname $0`
+. $cwd/bin/common.sh
+
+$cwd/bin/setup-host-check.sh
+check_status
+
+$cwd/bin/setup-package-install.sh
+check_status
+
+$cwd/bin/setup-targetfs-nfs.sh
+check_status
+
+$cwd/bin/setup-tftp.sh
+check_status
+
+$cwd/bin/setup-minicom.sh
+check_status
+
+$cwd/bin/setup-uboot-env.sh
+check_status
+
+echo
+echo "DVSDK setup completed!"
+echo "Please continue reading the Software Developer's Guide for more information on"
+echo "how to develop software on the EVM"
--
1.7.0.4
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2010-08-04 15:22 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-08-04 15:17 [PATCH 1/1] ti-tisdk-setup: add recipe to install setup scripts Chase Maupin
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.