* [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection
@ 2010-08-20 2:38 Robert Nelson
2010-08-20 2:38 ` [PATCH v6 2/3] ARM: OMAP: Beagle: only Cx boards use pin 23 for write protect Robert Nelson
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Robert Nelson @ 2010-08-20 2:38 UTC (permalink / raw)
To: tony; +Cc: linux-omap, Robert Nelson, Jarkko Nikula
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
---
arch/arm/mach-omap2/board-omap3beagle.c | 88 +++++++++++++++++++++++++++++++
1 files changed, 88 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 87969c7..1aebb3f 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -50,6 +50,93 @@
#define NAND_BLOCK_SIZE SZ_128K
+/*
+ * OMAP3 Beagle revision
+ * Run time detection of Beagle revision is done by reading GPIO.
+ * GPIO ID -
+ * AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
+ * C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
+ * C4 = GPIO173, GPIO172, GPIO171: 1 0 1
+ * XM = GPIO173, GPIO172, GPIO171: 0 0 0
+ */
+enum {
+ OMAP3BEAGLE_BOARD_UNKN = 0,
+ OMAP3BEAGLE_BOARD_AXBX,
+ OMAP3BEAGLE_BOARD_C1_3,
+ OMAP3BEAGLE_BOARD_C4,
+ OMAP3BEAGLE_BOARD_XM,
+};
+
+static u8 omap3_beagle_version;
+
+static u8 omap3_beagle_get_rev(void)
+{
+ return omap3_beagle_version;
+}
+
+static void __init omap3_beagle_init_rev(void)
+{
+ int ret;
+ u16 beagle_rev = 0;
+
+ omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
+ omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
+
+ ret = gpio_request(171, "rev_id_0");
+ if (ret < 0)
+ goto fail0;
+
+ ret = gpio_request(172, "rev_id_1");
+ if (ret < 0)
+ goto fail1;
+
+ ret = gpio_request(173, "rev_id_2");
+ if (ret < 0)
+ goto fail2;
+
+ gpio_direction_input(171);
+ gpio_direction_input(172);
+ gpio_direction_input(173);
+
+ beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
+ | (gpio_get_value(173) << 2);
+
+ switch (beagle_rev) {
+ case 7:
+ printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
+ break;
+ case 6:
+ printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
+ break;
+ case 5:
+ printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
+ break;
+ case 0:
+ printk(KERN_INFO "OMAP3 Beagle Rev: xM\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
+ break;
+ default:
+ printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+ }
+
+ return;
+
+fail2:
+ gpio_free(172);
+fail1:
+ gpio_free(171);
+fail0:
+ printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+
+ return;
+}
+
static struct mtd_partition omap3beagle_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
{
@@ -464,6 +551,7 @@ static struct omap_musb_board_data musb_board_data = {
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
+ omap3_beagle_init_rev();
omap3_beagle_i2c_init();
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
--
1.7.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v6 2/3] ARM: OMAP: Beagle: only Cx boards use pin 23 for write protect
2010-08-20 2:38 [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Robert Nelson
@ 2010-08-20 2:38 ` Robert Nelson
2010-08-20 2:38 ` [PATCH v6 3/3] ARM: OMAP: Beagle: no gpio_wp pin connection on xM Robert Nelson
2010-08-20 12:03 ` [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Jarkko Nikula
2 siblings, 0 replies; 5+ messages in thread
From: Robert Nelson @ 2010-08-20 2:38 UTC (permalink / raw)
To: tony; +Cc: linux-omap, Robert Nelson
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
---
arch/arm/mach-omap2/board-omap3beagle.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 62d69a9..e9af4fd 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -274,7 +274,8 @@ static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- if (system_rev >= 0x20 && system_rev <= 0x34301000) {
+ if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
+ (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
mmc[0].gpio_wp = 23;
} else {
--
1.7.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v6 3/3] ARM: OMAP: Beagle: no gpio_wp pin connection on xM
2010-08-20 2:38 [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Robert Nelson
2010-08-20 2:38 ` [PATCH v6 2/3] ARM: OMAP: Beagle: only Cx boards use pin 23 for write protect Robert Nelson
@ 2010-08-20 2:38 ` Robert Nelson
2010-08-20 12:03 ` [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Jarkko Nikula
2 siblings, 0 replies; 5+ messages in thread
From: Robert Nelson @ 2010-08-20 2:38 UTC (permalink / raw)
To: tony; +Cc: linux-omap, Robert Nelson
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
---
arch/arm/mach-omap2/board-omap3beagle.c | 4 +++-
1 files changed, 3 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index e9af4fd..1f455c3 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -274,7 +274,9 @@ static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
+ if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+ mmc[0].gpio_wp = -EINVAL;
+ } else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
mmc[0].gpio_wp = 23;
--
1.7.0.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection
2010-08-20 2:38 [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Robert Nelson
2010-08-20 2:38 ` [PATCH v6 2/3] ARM: OMAP: Beagle: only Cx boards use pin 23 for write protect Robert Nelson
2010-08-20 2:38 ` [PATCH v6 3/3] ARM: OMAP: Beagle: no gpio_wp pin connection on xM Robert Nelson
@ 2010-08-20 12:03 ` Jarkko Nikula
2010-09-23 17:26 ` Tony Lindgren
2 siblings, 1 reply; 5+ messages in thread
From: Jarkko Nikula @ 2010-08-20 12:03 UTC (permalink / raw)
To: Robert Nelson; +Cc: tony, linux-omap
On Thu, 19 Aug 2010 21:38:44 -0500
Robert Nelson <robertcnelson@gmail.com> wrote:
> Due to the omap3530 ES3.0 Silicon being used on both the
> B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
> routines to differentiate the Beagle Boards.
>
> However gpio pins 171,172,173 where setup for this prupose, so
> lets use them.
>
> Changes:
> for older U-Boot's, use omap_mux_init_gpio()
> keep Beagle Rev in board-omap3beagle.c
> gpio_free on gpio request failure
>
> Tested on Beagle Revisions: B5, C2, C4, and xMA
>
> Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> Cc: Jarkko Nikula <jhnikula@gmail.com>
> ---
To this set:
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection
2010-08-20 12:03 ` [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Jarkko Nikula
@ 2010-09-23 17:26 ` Tony Lindgren
0 siblings, 0 replies; 5+ messages in thread
From: Tony Lindgren @ 2010-09-23 17:26 UTC (permalink / raw)
To: Jarkko Nikula; +Cc: Robert Nelson, linux-omap
* Jarkko Nikula <jhnikula@gmail.com> [100820 04:55]:
> On Thu, 19 Aug 2010 21:38:44 -0500
> Robert Nelson <robertcnelson@gmail.com> wrote:
>
> > Due to the omap3530 ES3.0 Silicon being used on both the
> > B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
> > routines to differentiate the Beagle Boards.
> >
> > However gpio pins 171,172,173 where setup for this prupose, so
> > lets use them.
> >
> > Changes:
> > for older U-Boot's, use omap_mux_init_gpio()
> > keep Beagle Rev in board-omap3beagle.c
> > gpio_free on gpio request failure
> >
> > Tested on Beagle Revisions: B5, C2, C4, and xMA
> >
> > Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
> > Cc: Jarkko Nikula <jhnikula@gmail.com>
> > ---
>
> To this set:
>
> Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Adding all three.
Tony
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2010-09-23 17:26 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-08-20 2:38 [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Robert Nelson
2010-08-20 2:38 ` [PATCH v6 2/3] ARM: OMAP: Beagle: only Cx boards use pin 23 for write protect Robert Nelson
2010-08-20 2:38 ` [PATCH v6 3/3] ARM: OMAP: Beagle: no gpio_wp pin connection on xM Robert Nelson
2010-08-20 12:03 ` [PATCH v6 1/3] ARM: OMAP: Beagle: revision detection Jarkko Nikula
2010-09-23 17:26 ` Tony Lindgren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.